Heavy & Ultra Heavy duty clutches for pile to pile and pile to sheet pile connections
|
|
- Julius Mitchell
- 6 years ago
- Views:
Transcription
1 SteelWall & Mill-Pro Heavy & Ultra Heavy duty clutches for pile to pile and pile to sheet pile connections April 3, 2014
2 Clutch History Traditional Larssen Clutch bars have been around as long as Larssen sheet piles The C9 Clutch bar is a well known proprietary product of Arcelor but there are also equivalent products such as the SteelWall L8 a 1000Kn/m rated clutch. SteelWall is a German Clutch bar specialist (Est. 1989). In 2006 SteelWall developed the 12mm LPB family of Heavy Clutches. Rated 50% higher than traditional C9 or L8 bars, the LPB fully integrates with AZ, Z & U section sheet piles and exceeds 1500Kn/m max tensile load. Installed base is ~100,000 linear meters and will exceed 250,000m by end of 2014 Pipe-Pipe-Combi wall creation with a single product
3 Comparing Clutches Rated Tensile Strength Comparison Clutch bars - Kn/m Max Tensile Load Kn/m mm Cold Rolled Clutch L8 (C9) Hot Rolled Clutch LPB 100/ LPB 100/ FD Three Point Clutch Standard Clutches Heavy Clutch Ultra Heavy Clutches Standard, Heavy & Ultra Heavy duty clutches
4 Traverse Shear Transfer in Clutched Pipe Walls Clutch to pipe with full penetration welds and fully coated
5 Gorodets Project at River Wolga, Russia 1500Kn/m rated LPB180 clutch bars Rock & Silt Geotech
6 Combi Walls LPB100/180 While hot rolled and extruded clutch bars are inherently strong, the SteelWall design also allows up to 25% roatation about the clutch axis affording the flexibility essential during driving allignment. The LPB 12mm sections are completely interconnectable with Larssen type Z & U sheet piles. Pile to Pile with 100, 180, 268mm spacing Pile to Larssen Z sheet Pile, (AZ, Arcelor, Hoesch) Pile to Larssen U Sheet piles LPB s Connect to themselves + AZ, Z & U Larssen sheets
7 LPB100-16, LPB180-16, LPB247 ~ 16mm 0.62 Variants include the LPB100, allowing closer pile to pile centres and the LPB247 to match Japanese fabricated Clutch spacings. The LPB100/ is a thicker section providing increased tensile load of >2000Kn/m (not interconnectable with sheet). Manufactured from Grade S355 steel (Min YP 350Mpa), the LPB100/180 is welded using full penetration welds. As with sheet pile, binding clutches allow the transfer of traverse shear stress between piles up to the clutch rating. All LPB series clutches are strong enough to correct pile twist during driving, acting as a guide for the adjacent pile being driven and are suitable for driving directly into rock - including substrate granite. Clutches can be coated to the same standard as the pile up to the interface which can be sealed with clutch sealant to provide a wateright joint. SteelWall connectors comply to EuroCode &10249
8 1500 & 2000Kn/m Rated Clutch Bars Independent testing The LPB100/180 a 12mm section rated for 1500Kn/m in tensile and travserse shear stress The LPB rated for 2000Kn/m maximum tensile strength with full penetration welds Larssen type connection interconnectable with AZ, Z & U Sheet Piles (Arcelor, Hoesch, TK) Can be fully coated externally and driven with pre applied sealant for a fully watertight joint Fully coated watertight high load clutch joints
9 FD180 3 Point Ball & Socket Clutches The FD180 is a Grade S355 12mm section ball & socket type joint. The three points of connection provide a huge increase in tensile load transfer - up to 3400Kn per m of clutch. FD180 It is not compitable with Larssen sections, however it is ideal for pile to pile clutching where geotech forces the piles to share loads across them The 12mm section minimises heat input during welding whilst increasing load bearing capability The FD180 must be installed in the correct orientation Ultimate tensile & shear capacity
10 3400Kn/m Rated Clutch Bar Independent testing The FD180 is rated for 3400Kn/m maximum tensile strength with full penetration welds Three point connection using a 12mm section in Grade 355Mpa provides incredible tensile strength and shear force transfer for pile to pile connections Can be fully coated externally and driven with pre applied sealant for a fully watertight joint 20m of clutch provides 68,000Kn of tensile strength
11 Clutched Pile Coating System Mill-Pro has developed an exceptional coating methodology for clutched piles. Utalising the Lonkey process, we apply & cure up to 4000m2/day of Ultra High build epoxy 1500um thick, to AS/NZS , then apply clutches and post coat the clutch area (~10% of the surface). Using the same 100% solids epoxy, clutches are fully cured in 3-5 hours This allows the pipes to be coated and handled immediatly eliminating coating damage 1500um ultra high build epoxy fully cured in 15 minutes
12 Clutched Pile Coating System The Longkey process applies FOUR 75% overlapping wet on wet coats of 100% solids UHB epoxy to a maximum DFT of 1500um. Hot applied to a hot substrate - Post heated to fully cure in 15 minutes. The result is ~ 40% increase in the typical mechanical propoerties of high build epoxies: (Adhesion, Cathodic disbondment, hardness, abrasion resistance, impact strength) Application is highly accurate with the nominated DFT controlled within +/-7% 1500um ultra high build epoxy fully cured in 15 minutes
13 Clutched Pile Coating System CROSS SECTION WITH CLUTCH AREA PRIMED Pipes are coated using the Longkey process Blasted Strip is primed after masking removed to protect blasted area before clutch welding. In a separate operation clutches blasted externally to AS SA2.5 50um and primed with Sigma weld 165 CLUTCH FITTED & WELDED Pipes are is held in a Jig, Clutches are tacked in place to ensure alignment, Existing coating is protected using covers built into the Jigs and on the pipes themselves The Clutch is welded with full penetration fillet welds on each side. Pile is rotated and action is repeated on the other side of the pile CLUTCHED PILE PREPARED NDE of the weld, area mechanically abraded to SSPC- SP11 or pencil blasted to AS Existing epoxy edges are feathered as a key for the manual clutch coating to The Inside of the clutch has a stripe coat of Sigma Shield 880 applied by brush to prevent bleeding during shipping and storage, Clutches cannot be not fully coated inside COATING REINSTATED Clutches and primed area coated with the required DFT of 880XS hot applied Cold cured 100% solids epoxy Operation by hand in a temperature controlled environment Coating is final inspected & holiday tested Piles are protected with dunnage for transport & slung for load out Piles & clutches are fully coated & protected
14 Clutched Pile Coating System The result is a fully coated clutched pile ready to drive 1500um ultra high build epoxy fully cured in 15 minutes
15 Fabricated clutch connectors L sections are tack welded on one side into place, a partial or full penetration weld is applied from the outside. A corrosponding Internal backing weld is not possible due to size constriant L section fold out when load is applied is the typical failure mode, limiting shear transfer Post grouting of the L&T to prevent water inflows is typically highly unsucessful Full penetration welds and coating are simply not possible on the inside of L sections L sections tend to fold out when load is applied No weld or coating inside the clutch, tidal through flow
16 Fabricated clutch connectors Typical T created using 2 x 8mm G250Mpa flat bars Typically in L&T clutching the desired size or grade sections are not available, so they are fabricated from flat bar creating up to 12 welds per joint Not ideal for immersed sea walls where coating is not possible and tidal flow constantly brings freshly oxygnated water into the clutch. Rolled L&T sections are typically not available in size or grade
17 Pile Ovality Ovality can increase from 0.5% upto 3% due to full penetration clutch welding. Excessive ovality can cause major pile allignment problems during pile driving and in the driving gates. DSAW Helically formed (Spiral) pipe has typical ovality of ~0.5% of Diameter. Ovality resulting from heat input is a function of length of weld, weld size & type, pile diameter, pipe thickness (D/t ratio) Ovality increases through the axis the clutches are fitted, causing pile driving alignment issues On L8 (C9) type clutches, full penetration welds are not possible due to the radii involved. Staggered alternate fillet welds in 500mm long runs from oposing ends helps to reduce heat input. LPB & FD clutch bars can be welded using full penetration welds but L&T s cannot. Minimise heat input to avoid ovality issues
18
BEARINGS The lower bearing assemble is constructed to allow continuous operation when fully submerged in wastewater.
GENERAL SPECIFICATION INTENT The equipment to be supplied by manufacturer includes the screw pumps, support for the drive unit, profile plates, motors, gearboxes, couplings, guards, upper and lower bearing
More informationMATERIALS FOR SALE OR RENT YOUR PARTNER IN INFRASTRUCTURE
YOUR PARTNER MATERIALS FOR SALE OR RENT IN INFRASTRUCTURE About Infrasteel InfraSteel is a large supplier of steel products from Europe and beyond. Customers can rely on our support for both large and
More informationTapecoat. Application Guideline
Tapecoat Application Guideline Hot Applied Tapes 1.0 SCOPE This document contains general instructions and recommended practices for the application of the TC 20 hot applied tape coating system. For assistance
More informationROLL-UP COVERS Special Products
SURE-SPRING (Patented) The P.E.I. Patented design known as SURE-SPRING represent the most advanced level of technical innovation in the field of roll-up covers. The spring mechanism design takes into account
More informationPiling Product Guide Edition. Servicesteel.org
Piling Product Guide 2017 Edition Strong Foundations Starith Service Steel Service Steel Supplies All Your Foundation Products You Are Our Number One Priority From industry leading steel sheet piling to
More informationtwo component high build polyamine adduct cured coaltar epoxy primer/ coating
5 pages Revision of September 2004 DESCRIPTION two component high build polyamine adduct cured coaltar epoxy primer/ coating PRINCIPAL CHARACTERISTICS outstanding sea water resistance (outside hull and
More informationPRODUCT DATA SHEET SP-1386
DESCRIPTION: ADVANTAGES: SP-1386 is a hybrid two-component elastomeric polyurethane coating designed for long-term corrosion protection of steel and concrete substrates. SP-1386 is available in Spray Grade
More informationBRISTLE BLASTING SURFACE PREPARATION METHOD FOR MAINTENANCE. Neil Wilds
Paper No. 09004 2009 BRISTLE BLASTING SURFACE PREPARATION METHOD FOR MAINTENANCE Neil Wilds International Paint Ltd., Protective Coatings Stoneygate Lane, Gateshead Tyne and Wear, NE10 0JY United Kingdom
More information3.1 Available sections, terms of delivery
3.1 Interlocks LARSSEN section Interlock design conforming to DIN EN 10248-2 and E 67 of EAU 2004 LARSSEN 43, 430 HOESCH section (LARSSEN interlock) Interlock design conforming to DIN EN 10248-2 and E
More informationROLL-UP COVERS Standard products
A ROLL-UP COVERS Standard products P.E.I. Roll-up Covers are normally equipped with our patented system of multiple springs. This offers countless advantages: Reliability Compact size Extremely high speeds
More informationTrutek TCM 385RE - Pure Epoxy 3:1
Features and Benefits Version 23/12/2013 High bond strength with High load resistance Used with all grades of threaded rod and rebar in accordance with TR029 Ideal for deep embedment installations Used
More informationWXGUARD WIND SEGMENTED LIGHTNING DIVERTER STRIPS INSTALLATION GUIDE.
WXGUARD WIND SEGMENTED LIGHTNING DIVERTER STRIPS INSTALLATION GUIDE www.wxguardwind.com Shine Wire Products, Inc. 25 Print Works Drive Adams, MA 01220 1-800-543-5151 www.shinewire.com WXGuard is the new
More informationROLL-UP COVERS. Special Product: SURE-SPRING.
Special Product: SURE-SPRING The P.E.I. Patented design known as SURE-SPRING represent the most advanced level of technical innovation in the field of roll-up covers. The spring mechanism design takes
More informationMAE 322 Machine Design Shafts -3. Dr. Hodge Jenkins Mercer University
MAE 322 Machine Design Shafts -3 Dr. Hodge Jenkins Mercer University Setscrews Setscrews resist axial and rotational motion They apply a compressive force to create friction The tip of the set screw may
More informationSurface Preparation and Application of Ronass Pipe Shield 1319
Surface Preparation and Application of Ronass Pipe Shield 1319 RONASS TECHNICAL SUPPORT TEAM WWW.RONASS.COM SUPPORT@RONASS.COM PROTECTIVE COATINGS MARINE COATINGS DECORATIVE COATINGS Introduction Ronass
More informationUniflex-stow remote valve operating systems
Flexible shaft system 1 INTRODUCTION The purpose is to provide the user with basic information for the specification, installation, operation, maintenance, repair and parts identification of the Uniflex-stow
More informationNAVSEA REVIEWED ASTM F-718. SeaVoyage Copper Free Antifoulant; N51R301 Red, N51B301 Black, N51L301 Blue
ASTM F-718 The Sherwin Williams Company SeaVoyage Copper Free Antifoulant PRODUCT DESIGNATIONS SeaVoyage Copper Free Antifoulant; N51R301 Red, N51B301 Black, N51L301 Blue MIL-PRF-24647 If this product
More informationArcelorMittal Europe - Long products Sections and Merchant Bars HISTAR. Innovative high strength steels for economical steel structures
ArcelorMittal Europe - Long products Sections and Merchant Bars HISTAR Innovative high strength steels for economical steel structures Shanghai World Finance Center, P.R. China Innovative high strength
More informationNAVSEA REVIEWED ASTM F-718. If this product is to be applied as part of a coating system, all components of the system must be as listed on the QPL.
ASTM F-718 The Sherwin-Williams Company SeaGuard 5000 HS PRODUCT DESIGNATION Part A: N11-350 base color series Part B: N11V350 hardener MIL-PRF-23236 MIL-PRF-24647 If this product is to be applied as part
More informationNAVSEA REVIEWED ASTM F-718. Chesterton ARC 855N, Ceramic Filled Epoxy Coating
ASTM F-718 ARC Composite Technology Chesterton ARC 855N, Ceramic Filled Epoxy Coating MIL-PRF-32171 If this product is to be applied as part of a coating system, all components of the system must be as
More informationCOMPFIRE. Reaction Frame. Camera 3. Macalloy Bars. Camera 2. Link Bar. Support Beam. Oven Bar. Camera 1. Jack Bar.
Reaction Frame Macalloy Bars Camera 3 Support Beam α Oven Bar Camera 2 Link Bar Camera 1 Tested Connection Jack Bar Electrical Furnace Reaction Frame Load Jack 22 September 2010 1 Oven Bar Link Bar View
More informationPB-170B - Hydraulic NC Pressbrake 176T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge
PB-170B - Hydraulic NC Pressbrake 176T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge Ex GST Inc GST $40,950.00 $45,045.00 ORDER CODE: S909 MODEL: Control Unit (Type): PB-170B Estun
More informationHVS S 15kV Class
Product HVS-3-1580S 15kV Class Transition Splice for 3/C to 3/C Extruded Dielectric (Poly/EPR) Power Cables Raychem Corporation Electrical Products 8000 Purfoy Road Fuquay-Varina, NC 27526 PII-54864, Rev
More information...our linkages, your solution. Rod Ends
...our linkages, your solution Technical Information Introduction All of our rod ends incorporate either a plain spherical bearing, ball bearing, or roller bearing. Below is an overview of each type. Plain
More informationA Quick reference guide to the installation of Uniflex. Oldham Seals Group. Uniflex installation Guide
A Quick reference guide to the installation of Uniflex. Oldham Seals Group Uniflex installation Guide Uniflex Guide From Oldham Seals Group Introduction: Uniflex systems provide a means of remote Valve
More informationBoat Hull, Propeller and Top-Side Protection
TM Boat Hull, Propeller and Top-Side Protection Increased performance Reduced maintenance Non-Toxic Nano-technology cathodic protection WORK or PLEASURE COMMERCIAL or SPORT PROTECTION AND PERFORMANCE IS
More informationInterspec. Technical Specification. Scripps Institute of Oceanography. Melville. California- San Francisco, U.S.A. 19-Nov-2013.
Where legislation does not explicitly restrict or limit the use of lead containing coatings it is the responsibility of the client to inform International Paint in writing of their specific requirements
More informationNOVAGUARD 810. PRODUCT DATA SHEET December 11, 2014 (Revision of April 1, 2014) DESCRIPTION
DESCRIPTION Two-component, solvent-free, amine rapid-cured novolac phenolic epoxy coating PRINCIPAL CHARACTERISTICS One-coat tank coating system Excellent resistance to crude oil up to 90 C (194 F) Suitable
More informationSEVENTH EDITION HOT ROLLED AND STRUCTURAL STEEL PRODUCTS
SEVENTH EDITION HOT ROLLED AND STRUCTURAL STEEL PRODUCTS HOT ROLLED AND STRUCTURAL STEEL PRODUCTS CONTENTS INTRODUCTION 1 TEST CERTIFICATES AND 2 CERTIFICATES OF COMPLIANCE BUILD WITH STANDARDS AND ACRS
More informationTechnical Data Sheet. Humidur ME Product Description. Manufacturer s Information
Technical Data Sheet Humidur ME Product Description Humidur ME is a 2-component solvent-free modified polyamine cured epoxy system offering the following benefits: Long term protection in highly corrosive
More informationIntroduction. What is Powercore? Powercore Welding Rod is an " Electro-fusion System" used for joining all types of thermoplastic parts together.
Introduction What is Powercore? Powercore Welding Rod is an " Electro-fusion System" used for joining all types of thermoplastic parts together. Powercore Welding Rod, is a flexible thermoplastic rod approximately
More informationPB-135B - Hydraulic NC Pressbrake 135T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge - Includes Safety Light Guarding
PB-135B - Hydraulic NC Pressbrake 135T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge - Includes Safety Light Guarding On Sale Ex GST Inc GST $39,500.00 $45,425.00 $38,500.00 $44,275.00
More informationDesign principles and Assumptions
Design principles and Assumptions The design and use of concrete slabs that utilise ARMOURDECK 300 in composite construction may be carried out using either: the relevant Australian and international Standards
More informationPB-70B - Hydraulic NC Pressbrake 70T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge - Includes Safety Light Guarding
PB-70B - Hydraulic NC Pressbrake 70T x 3200mm Estun NC-E21 Control 2-Axis with Hardened Ballscrew Backgauge - Includes Safety Light Guarding Ex GST Inc GST $29,400.00 $32,340.00 $27,950.00 $30,745.00 Special
More informationSeries 500. Liquid Level Transmitters. Instruction Manual
Series 500 Liquid Level Transmitters Instruction Manual Contents Section Content Page 1 Introduction 1.1 General Overview 3 1.2 Mounting Options 3 2 Installation Notes 2.1 Transmitters 4 2.1.1 Model 510
More information3M Scotchkote Liquid Epoxy Coating 323+
Application Guide August 2017 1 of 12 Plural Component Spray Application: 1.0 Scope 1.1 This guide defines the application requirements of Scotchkote coating 323+ applied to steel substrates for buried
More informationApplication Guide for MasterSeal Sealants MasterSeal NP 430 MasterSeal CR 195
Application Guide for MasterSeal Sealants MasterSeal NP 430 MasterSeal CR 195 April 2018 Page 1 of 11 JOINT DESIGN The number of joints and the joint width should be designed for a maximum of ±25% movement.
More informationCERTIFICATE OF ACCREDITATION
CERTIFICATE OF ACCREDITATION ANSI-ASQ National Accreditation Board 500 Montgomery Street, Suite 625, Alexandria, VA 22314, 877-344-3044 This is to certify that Charter Coating Service (2000) Ltd. Suite
More informationNODIA AND COMPANY. Model Test Paper - I GATE Machine Design. Copyright By Publishers
No part of this publication may be reproduced or distributed in any form or any means, electronic, mechanical, photocopying, or otherwise without the prior permission of the author. Model Test Paper -
More informationSURE-SPRING SURE-SPRING, HP VERSION. ROLL-UP COVERS Special products. 18
SURE-SPRING The P.E.I. Patented design known as SURE-SPRING represent the most advanced level of technical innovation in the field of roll-up covers. (Patented) Suitable for HIGH SPEED operation The multiple
More informationTrelleborg en g INeereD SYSTeMS Marine Fenders
Marine Fenders Why Trelleborg Fenders? There is a simple reason to use our fenders: it is just too expensive not to do so. Every modern marina, port or harbour invests in the protection of their structures
More informationMIL-STD-883G METHOD LEAD INTEGRITY
LEAD INTEGRITY 1. PURPOSE. This method provides various tests for determining the integrity of microelectronic device leads (terminals), welds, and seals. Test condition A provides for straight tensile
More informationElcometer 506 Pull- Off Adhesion Gauge. elcometer.com 1
Elcometer 506 Pull- Off Adhesion Gauge elcometer.com 1 Elcometer 506 STANDARDS: ASTM D4541, ASTM D7234, AS/NZS 1580.408.5, BS 1881-207, DIN 1048-2, EN 12636, EN 13144, EN 1542, EN 24624, ISO 16276-1, ISO
More informationBEST PRACTICES REPORT. Tank Car Lessee PROJECT OVERVIEW: Industrial Customer: A chemical company.
NANO-CLEAR INDUSTRIAL FLUOROPOLYMER COATING WATER FOR TANK FEATURE CAR CENTER PROTECTION BAND After NCI Tank Car Lessee Industrial Customer: A chemical company. Project: Top coat the center band of tank
More informationNAVSEA REVIEWED ASTM F-718. Intershield 300HS, High-Solids Abrasion- Resistant Aluminum Pure Epoxy Anticorrosive
ASTM F-718 International Paint LLC Intershield 300HS, High-Solids Abrasion- Resistant Aluminum Pure Epoxy Anticorrosive PRODUCT DESIGNATIONS Part A: ENA380 Bronze or ENA381 Aluminum (Gray) Part B: ENA383
More informationPSPC Guideline & its effect
1 Guideline & its effect 2007. 10. 19. Guideline 2 Content 3 History & Progress Inspector Primary Surface Preparation Edge grinding Steel preparation Secondary Surface Preparation Surface Preparation after
More informationNAVSEA REVIEWED ASTM F-718. Part A: B62L230 OAP Blue, B62W230 White, B62RW230 Red Oxide, B62AW230 Haze Gray
ASTM F-718 The Sherwin Williams Company Fast Clad ER PRODUCT DESIGNATIONS Part A: B62L230 OAP Blue, B62W230 White, B62RW230 Red Oxide, B62AW230 Haze Gray Part B: B62V230 Clear, B62GV230 Light Green, B62AV230
More informationUK PG 6/23(92) Appendix 3: max g/l (approx. 3.6 lb/us gal) 5.7 m²/l for 100 µm (229 ft²/us gal for 4.0 mils)
DESCRIPTION Universal epoxy anticorrosive primer, based upon pure epoxy technology PRINCIPAL CHARACTERISTICS Universal epoxy primer system suitable for Ballast Tanks, Decks, Topside, Superstructure, Hull
More informationROOFING SOLUTIONS DESIGN GUIDE PURLINS AND GIRTS DESIGN GUIDE PURLINS AND GIRTS S&T029N
DESIGN GUIDE PURLINS AND GIRTS ROOFING SOLUTIONS DESIGN GUIDE PURLINS AND GIRTS S&T029N JUL 2015 CONTENTS INTRODUCTION 2 Acknowledgements 2 Disclaimer 2 Product Technical Statement 3 Producer Statement
More informationAlligatoring Pronounced wide cracking over the surface of a coating, which has the appearance of alligator hide.
OQ Task Name Task 7.1 Perform Visual Inspection of Atmospheric Coatings 1.0 Task Description This task consists of the visual inspection of pertains to above-ground normally exposed pipeline components
More informationEKSPAN - K SERIES BEARINGS - BS 5400
EKSPAN - K SERIES BEARINGS - BS 5400 EKSPAN Other design standards Description Bearing types K series bearings are available in three types - Typical 31K details Attachment Support and Installation 30K
More informationNAVSEA REVIEWED ASTM F-718. If this product is to be applied as part of a coating system, all components of the system must be as listed on the QPL.
ASTM F-718 International Paint LLC Intertuf 6, Two Pack Anticorrosive Epoxy Primer PRODUCT DESIGNATIONS Part A: KH Series Part B: KHA6 MIL-PRF-336 MIL-PRF-67 If this product is to be applied as part of
More informationVARIABLE SPRING SUPPORTS BV35, BV70, BV140, BV210
SUPPORTS 35, 70, 140, 210 GENERAL Variable spring supports are used for supporting pipework, vessels, columns and pipe connections to large tanks, that are subject to thermal movement and/or subsidence.
More informationGearbox Installation Manual
Gearbox Installation Manual Rotork Gears IW, MOW, MTW, IB and IS ranges (Electronic copy available on www.rotork.com)! This manual contains important safety information. Please ensure it is thoroughly
More informationBosch Seat Motor _spec_sheet_-_Bosch_FRC_motor_6_004_.pdf. FRC_Bosch_motor_V2_6_004_RA3_ zip
Bosch Seat Motor Specification Sheet 2016-12-21_spec_sheet_-_Bosch_FRC_motor_6_004_.pdf CAD File FRC_Bosch_motor_V2_6_004_RA3_194-06.zip Motor Mounting & Shaft Support: Suggested Motor relies on two solid
More informationSheet 1 Variable loading
Sheet 1 Variable loading 1. Estimate S e for the following materials: a. AISI 1020 CD steel. b. AISI 1080 HR steel. c. 2024 T3 aluminum. d. AISI 4340 steel heat-treated to a tensile strength of 1700 MPa.
More information60 Drive Design & Maintenance Manual FRICTION BELT DRIVES. Max. Bore Pulley F J K L M N Outside Code Dia (P) Grooves No. Metric Inch Type Dia (O)
Catalogue Pitch No. of Bush Max. Bore Pulley F J K L M N Outside Code Dia (P) Grooves No. Metric Inch Type Dia (O) 031Z0041 56 1 1008 25 1 9 49 28 13 22 60 Z0042 56 2 1108 28 1 1 /8 9 49 35 27 22 60 031Z0051
More informationUSV Ultra Shear Viscometer
USV Ultra Shear Viscometer A computer controlled instrument capable of fully automatic viscosity measurements at 10,000,000 reciprocal seconds Viscosity measurement background Accurate measurement of dynamic
More informationElcometer 506 Pull- Off Adhesion Gauge. Product Brochure/Flyer. 506 PAT Adhesion Tester
Product Brochure/Flyer Elcometer 506 Pull- Off Adhesion Gauge elcometer.com 1 Copyright 2016 Burwell Technologies For more information: 1300 287 935 / mail@burwell.com.au / www.burwell.com.au Elcometer
More informationNOVAGUARD 890. PRODUCT DATA SHEET January 21, 2015 (Revision of December 12, 2014) DESCRIPTION
DESCRIPTION Two-component, solvent-free, amine-cured novolac phenolic epoxy coating PRINCIPAL CHARACTERISTICS One-coat tank coating system Excellent resistance to crude oil up to 120 C (250 F) Suitable
More informationPipe fittings MUST be installed by a certified welder only. +GF+ SIGNET will not assume liability of any kind for improper fitting installations.
+GF+ SIGNET 0 High Performance Flow Sensor (English) -0.090- F-/99 English SAFETY INSTRUCTIONS. Do not remove from pressurized lines.. Do not exceed maximum temperature/pressure specifications.. Do not
More informationBRIDGEMONT BMS. The new force in weighbridge design
BRIDGEMONT BMS The new force in weighbridge design BridgeMont BMS The Avery Weigh-Tronix BridgeMont series is a new generation in weighbridge design. As the market leader in the UK, US and Canada, BridgeMont
More informationPVC PRESSURE PIPE SYSTEMS AS/NZS 4441, 4765, 1477 Potable water, non-potable water pressure applications
PVC PRESSURE PIPE SYSTEMS AS/NZS 4441, 4765, 1477 Potable water, non-potable water pressure applications JAN 2017 1 CONTENTS MATERIAL & DESIGN 3 PVC-O PRESSURE PIPE SERIES 2 5 PVC-M PRESSURE PIPE SERIES
More informationDOLLY PREPARATION FOR PULL-OFF ADHESION TESTING
DOLLY PREPARATION FOR PULL-OFF ADHESION TESTING INFO Abstract This articles focuses on the dolly preparation process and its importance in maximizing repeatability by ensuring a strong bond at the dolly-adhesive
More informationVW Surface-Mount Strain Gauge
VW Surface-Mount Strain Gauge 52650399 Copyright 2003 Slope Indicator Company. All Rights Reserved. This equipment should be installed, maintained, and operated by technically qualified personnel. Any
More informationMARINE SYSTEMS FOR DECKS SYSTEM. a six page issue January 2010 revision of May Application areas: all decks on ships, interior and exterior
Application areas: all decks on ships, interior and exterior Contains following specifications: a six page issue revision of May 2008 Specification 1: multi-purpose epoxy coating system Specification 2:
More informationSignet 2517 Brass Paddlewheel Flow Sensor * *
Signet 2517 Brass Paddlewheel Flow Sensor -250.090 English -2517.090 Rev. F 11/06 English SAFETY INSTRUCTIONS 1. Do not remove from pressurized lines. 2. Do not exceed maximum temperature/pressure specifi
More informationPipe fi ttings MUST be installed by a certifi ed welder only. Signet will not assume liability of any kind for improper fi tting installations.
Signet 50 High Performance Flow Sensor English *3-50.090* 3-50.090 C 05/06 English SAFETY INSTRUCTIONS 1. Do not remove from pressurized lines.. Do not exceed maximum temperature/pressure specifi cations.
More informationEngineering Specifications
Engineering Specifications Centerlign Weigh Modules The portions of this specification that have been left blank ( ) should be filled with information about the specific application. Information for the
More informationHYDRAULIC HAMMERS. To drive concrete piles, casings and sheet piles
HYDRAULIC HAMMERS To drive concrete piles, casings and sheet piles Hydraulic hammers are complementary to Vibrodrivers for certain applications. PTC hydraulic power packs with open loop circuit are designed
More informationAdhesion Tester Data Sheet / Instructions
Paint Test Equipment Adhesion Tester Data Sheet / Instructions Adhesion Tester Information ISO 4624: Paints and varnishes. Pull-off test for adhesion. ISO 16276-1: Corrosion protection of steel structures
More informationPRODUCT DATA SHEET SikaCor HM Mastic
PRODUCT DATA SHEET Adhesion layer epoxy based PRODUCT DESCRIPTION USES PROPERTIES SikaCor HM Mastic is a total solid 2pack coating system based on epoxy resin. Solvent free referring to Protective Coatings
More informationCV/LF and CV/CF. TICO Structural Bearings
CV/LF and CV/CF TICO Structural Bearings TICO CV/LF and TICO CV/CF Isolation of vibrations from one part of a building to another is as equally important as isolating the whole building itself. Indeed,
More informationVC Series. Volume Control Dampers M A N U F A C T U R E R S O F A I R, F I R E A N D S M O K E C O N T R O L P R O D U C T S
V41706 VC Series Volume Control Dampers Roll formed steel blades with three material options DW144 compliant Flanged models with 65mm deep mechanically fixed casings Rectangular spigotted models with 85mm
More informationIntelligent CST Drive System
Intelligent CST Drive System The Drive for Productivity With constant pressure for greater productivity, improving the performance of longwall systems remains a key goal for mine operators. At Caterpillar,
More information3M XYZ / Isotropic Electrically Conductive Adhesive Transfer Tape 9709S / 9709 SL
Technical Data October, 2009 3M XYZ / Isotropic Electrically Conductive Adhesive Transfer Tape 9709S / 9709 SL Product Description 3M Electrically Conductive Adhesive Transfer Tape 9709S is a pressure
More informationNAVSEA REVIEWED ASTM F-718. Part A: MS-200 / MS209R D. Gray / MS207R Green / MS205R Red / MS201R White / MS203R Yellow / MS218H Part B
ASTM F-718 ITW Engineered Polymers, American Safety Technologies (AST) MS-200 Acrylic Epoxy Color Topping PRODUCT DESIGNATIONS Part A: MS-200 / MS209R D. Gray / MS207R Green / MS205R Red / MS201R White
More informationMEDIUM DURABILITY MEDIUM DURABILITY
PPI NBR: 63001-012M-B (REV 01) DATE: September 07, 2004 MEDIUM DURABILITY PRESERVATION PROCESS INSTRUCTION (PPI) for VENT PLENUMS, DUCTS AND TRUNKS to be used in conjunction with CORE PPI 63101-000 with
More informationSIGMACOVER 805. PRODUCT DATA SHEET December 12, 2014 (Revision of April 1, 2013) DESCRIPTION
DESCRIPTION Two-component, high solids polyamine adduct cured epoxy coating PRINCIPAL CHARACTERISTICS Can be used directly to metal Very good surface wetting Excellent corrosion resistance Outstanding
More informationAPEM SERIES - POTENTIOMETER JOYSTICKS TWO STANDARD MOUNTING OPTIONS LOW CURRENT DRAIN IP65 ABOVE PANEL.
R 2.65 51.20 18.20 1.85 R 3.00 17.50 dia APEM R 4.50 28.75 3.60 4000 SERIES - POTENTIOMETER JOYSTICKS TWO STANDARD MOUNTING OPTIONS LOW CURRENT DRAIN IP65 ABOVE PANEL VARIETY OF POTENTIOMETER OPTIONS ROBUST,
More informationJF375E JF300E JMN150E. Load Time T load (hrs) Range Data. Maximum Fixture Thickness. Drill Hole Diam.
Product Information The Epoxy 2 Part injection resin is suitable for use in solid concrete, solid brickwork and natural stone. It can be used for installing threaded studs, rebar or internal threaded sockets.
More information48.5 B3 Mega POMMIER. Booms 24 to 48.5m
48.5 B3 Mega POMMIER Booms 24 to 48.5m POMMIER Today s alternative for farmers considering a lighter, stronger and wider boom option. One of the many benefits of POMMIER aluminium booms over steel is the
More informationPosiTest. Pull-Off Adhesion Tester. INSTRUCTION MANUAL v PosiTest AT-M (manual) PosiTest AT-A (automatic)
PosiTest Pull-Off Adhesion Tester INSTRUCTION MANUAL v. 4.0 PosiTest AT-M (manual) PosiTest AT-A (automatic) Introduction The portable, hand-operated PosiTest Pull-Off Adhesion Tester measures the force
More informationElbow ball check valves PRODUCT CATALOG
Elbow ball check valves PRODUCT CATAOG Version 01.16 Technical data Range of available diameters: 32 300. Pressure rated to PN 1.6 MPa (all valves are tested to PN 1.0 MPa leak test / PN 1.6 MPa hydrostatic
More informationCOMPFIRE SCFT-FP_20_55_ November 2010 Fin Plate Connection to Square Concrete-Filled Tube Test Result
Reaction Frame Macalloy Bars Camera 3 Support Beam α Oven Bar Camera 2 Link Bar Camera 1 Tested Connection Jack Bar Electrical Furnace Reaction Frame Load Jack 16 November 2010 1 Oven Bar Link Bar View
More informationHeavy-Duty Rod Ends - Male with integral spherical plain bearing
Heavy-Duty Rod Ends - Male with integral spherical plain bearing 65700 Order No. Thread (hand) d 1 l 1 d 2 d 3 d 4 l 2 l 3 X g H7 65700.W0005 Right 5 33 M 5 11,11 18 20 9 14 65700.W0006 Right 6 36 M 6
More informationOEM APPROVED AND USED
OEM APPROVED AND USED Pro Form's Pliogrip Truck Line epoxy and urethane adhesives are part of a complete system designed for the most demanding bonding applications in the truck refinish industry. www.proformproducts.com
More informationNAVSEA REVIEWED ASTM F-718. Interbond 998, Two-pack Anticorrosive High Solids Epoxy Deck Primer
ASTM F-718 International Paint LLC Interbond 998, Two-pack Anticorrosive High Solids Epoxy Deck Primer PRODUCT DESIGNATIONS Part A: KRA922/KRA924/KRA925/KRA92 Part B: KRA923 MIL-PRF-24667 If this product
More informationA flexible solution for a tough problem: What are the solutions available for conveyor belt repair?
A flexible solution for a tough problem: What are the solutions available for conveyor belt repair? http://files.belzona.com/mrktg/picture conveyor belt repair.zip Conveyor belts are an integral part and
More informationTank Armor ADVANCED LINING PROTECTION
Tank Armor ADVANCED LINING PROTECTION Vessels holding hazardous materials require a highperformance lining to protect the structure and its contents. Fighting corrosion from the inside out, Tnemec s Tank
More informationISO INTERNATIONAL STANDARD
INTERNATIONAL STANDARD ISO 18752 First edition 2006-07-15 Rubber hoses and hose assemblies Wire- or textile-reinforced single-pressure types for hydraulic applications Specification Tuyaux et flexibles
More informationProduct Brochure For K058. Description. Features. Auckland: (09)
HG-3206 & PB-135B - Hydraulic NC Guillotine & NC Pressbrake Package Deal Guillotine - 3200 x 6mm, Pressbrake 3200mm x 135 Ton Ezy-Set NC-89 & Estun NC-E21 Controls Package Deal Ex GST Inc GST $65,900.00
More informationc/ Required pre-requisite procedure(s): PREP Rev.01 Pre-painted or Primed Aluminum cleaning Procedure
a/title : Application Process for D200 on Pre-painted or Primed Aluminum b/ Description : This document explains the process of applying AquaSurTech D200 to pre-painted or primed aluminum using HVLP or
More informationCATALOGUE MEDIUM TO HEAVY DUTY IDLER
CATALOGUE MEDIUM TO HEAVY DUTY IDLER Sandvik Materials Handling PULLEYS, IDLERS AND MATERIALS HANDLING SYSTEMS INDEX 3 ROLL INLINE CARRY & IMPACT PAGE 3 3 ROLL INLINE PLAIN P/A TRAINER PAGE 5 SINGLE ROLL
More informationConveyor Belt Maintenance
Conveyor Belt Maintenance Conveyor belt maintenance not only includes proper care of the belt itself but also includes care and maintenance of the frame and accessories. The first step in the process is
More informationCORROSION PROTECTION CORROSION PROTECTION FEATURING RUST MORT RUST SEAL RUST TRAP RUST SHIELD RUST PREVENTER CAVITY WAX UNDERCOATINGS COMPARISON CHART
CP 0317 CORROSION PROTECTION CORROSION PROTECTION FEATURING RUST MORT RUST SEAL RUST TRAP RUST SHIELD RUST PREVENTER CAVITY WAX UNDERCOATINGS COMPARISON CHART RUST MORT WHEN TO USE IT: For the conversion
More informationWater Supply and Sewerage Approved Products Manual - February 2006
Water Supply and Sewerage Approved Products Manual - February 2006 Gravity Sewerage Products Vitrified Clay Pipeline System Section SGPS 02 Last updated Jan 2007 CONTENTS A SGPS 02-S1 PIPES TO EN 295 A
More informationNAVSEA REVIEWED ASTM F-718. Part A: 600D02 (Gray); 600D30 (Light Gray); and 600T04 (Buff) Part B: 610C02
Randolph Products ASTM F-718 Randogrip Metal Primer PRODUCT DESIGNATIONS Part A: 600D02 (Gray); 600D30 (Light Gray); and 600T04 (Buff) Part B: 610C02 MIL-PRF-24667 If this product is to be applied as part
More informationDirective 1999/13/EC, SED: max g/kg max g/l (approx. 2.6 lb/us gal) 6.6 m²/l for 100 µm (265 ft²/us gal for 4.
DESCRIPTION Two-component, high-build, amine adduct-cured novolac phenolic epoxy holding primer PRINCIPAL CHARACTERISTICS Primer coat in the PHENGUARD tank coating system Excellent resistance to a wide
More informationPH SERIES PH1000F-2000F SERIES. Heavy-duty rigid and foldable power harrows
KUBOTA PH POWER HARROWS PH1000-3000 SERIES PH1000F-2000F SERIES Heavy-duty rigid and foldable power harrows HEAVY-DUTY RIGID AND FOLDABL 2 Heavy-Duty Technology for Tough Conditions To meet the ever increasing
More information