Winterizing Supplies & Procedure 1999 Maristar 210 VRS, LTR 330 hp, EFI, MPI
|
|
- Bennett Boyd
- 5 years ago
- Views:
Transcription
1 Winterizing Supplies & Procedure 1999 Maristar 210 VRS, LTR 330 hp, EFI, MPI SUPPLIES/PARTS/TOOLS Supplies: Sta-Bil Fuel stabilizer (1 oz/2.5 gals); 45 gal tank = 18 oz. +/- 6 qts. engine oil (Pennzoil Marine 15w40 or 20 w50, API Service SJ/CG4 Racing oil). Oil Filter (Pennzoil PZ3 or PF25, Napa Gold 1069). Fogging Oil (the kind that produces white/gray smoke) 5 qts transmission fluid (Pennzoil Type A Dexron II, III or Dexron/Mercon). Impeller-Indmar GM 351, Johnson 608 crank driven (DIM Website Item #0714) Corrosion Protectant Spray (Pennzoil Marine Z-M Corrosion Protectant, Marvel Mystery Oil, West Marine Engine Protectant) Optional: RV Antifreeze (50/50 propylene glycol - environmentally friendly antifreeze. Capacities: Oil with filter change: 5.5 quarts Transmission oil: 4.4 quarts Tools: 5 section of garden hose with shut-off ball-valve 7/8 wrench-remove knock sensor Screw driver-flat blade-remove hose clamps Impeller puller Shop or paper towels Oil vacuum extractor Misc. Parts List: 8 Spark Plugs (AC Delco MR43LTS); Gap 0.045, 1.1mm. Alternator Belt All 5.7 Liter except LS1 - Indmar Thermostat Raw water cooled - Indmar Teak Oil: Deks Olje (pronounced olay) #1 Matte Finish; Star Brite Golden Teak Oil Page 1 of 5
2 A. Engine Winterization Procedure. 1) Fuel Stabilizer. Add fuel stabilizer to fuel (do this first so fuel in fuel lines and carburetor is stabilized). 2) Prepare the raw water intake hose. a) Remove the two hose clamps on the hose that connects to the brass thru-hull intake and slide them back on the water intake hose. b) Position raw water intake hose and insert about 18 inches of the garden hose extension with shut-off ball valve which has been connected to water source. Insure shut-off valve is in the off position and turn on the water source. 3) Change engine oil. a) Open shut-off valve so water flows into the raw water intake hose (not much flow is required). b) Start the engine. c) Run engine to normal operating temperature for minimum of 15 minutes (140 to 160), this insures the Sta-Bil reaches all of the fuel lines, injectors, etc. DO NOT EXCEED IDLE ( rpm). d) Shut-off the engine and turn off water supply at shut-off ball valve. e) Drain engine oil (use oil vacuum pump, place oil extension hose out off rear bilge drain hole). f) Remove engine oil filter (use 1 gallon freezer zip lock bag so oil in oil filter drains into zip lock bag). g) Install new oil filter. Fill new oil filter with ½ with new oil, use finger in some oil to put a thin layer of oil on the o-ring on new filter and hand tighten plus ¼ of a turn. h) Add 4-5 quarts of new engine oil through the valve cover removable cap. Confirm proper oil level with dip stick. DO NOT OVERFILL. 4) Change Transmission fluid. a) Unscrew the red transmission fluid dip stick. b) Using vacuum pump, extract as much transmission fluid as possible. c) Note the amount of used transmission fluid removed and replace with exact amount (specs call for 4.4 quarts or 4.16 liters). Note color and odor of used transmission fluid (if dark brown/red or a nutty odor could mean overheat, water in transmission, leak in transmission cooler core, or other issues. d) Add new transmission fluid and replace transmission dip stick screw cap. Confirm proper transmission oil level with dip stick. DO NOT OVERFILL. Page 2 of 5
3 5) Engine Fogging. a) This will be the last time the engine is run. b) Open water flow by opening the shut-off ball valve. c) Start the engine and let it run at idle speed. d) Remove the flame arrestor by removing the large hose clamp at the end of the intake manifold. e) Begin squirting the fogging oil into the intake manifold throttle plate (small hole on plate) continuously until white/gray smoke comes out of the exhaust (for about 10 to 15 seconds or 1/3 of the can). The engine will run roughly but keep squirting till you see the smoke. f) Turn off engine and water supply. g) Check for oil leaks and check engine and transmission oil level at dip stick, adjust as necessary. h) Clean the flame arrestor with carb or parts cleaner, dry well and reinstall. 6) Draining the Manifolds. a) At the end of each exhaust manifold there is a 1 diameter hose which connects to a yellow quick disconnect. b) Disconnect the quick disconnect and allow the water to drain into the bilge and leave quick disconnect disconnected until summarization. 7) Draining the Engine Block. a) Keep the raw water intake hose disconnected from the raw water intake through hull connection until summarization. Put the two hose clamps in zip lock bag. b) Remove the raw water intake hose from the impeller. Put hose clamp in zip lock bag. c) Remove the water hose to the bottom of the transmission cooler and place hose clamp in zip lock bag for summarization. d) Remove the remaining water hose on the impeller housing and place hose clamp in zip lock bag for summarization. e) Check the screen on the bottom of the transmission cooler for debris. f) Remove the water hose from the water pump output hose by removing the hose clamp. Put hose clamp in zip lock bag. g) Disconnect the neutral safety switch (so engine will not start) and crank the engine over very quickly (less than 5 seconds). This will remove water from the upper engine cooling system and pumps. h) Drain the water from both sides of engine block, both exhaust manifolds. (i) Remove engine block petcock drain valve and let water drain into the bilge. (ii) Using a coat hanger, poke around and remove any obstruction in the block. Page 3 of 5
4 (iii)replace petcock drain valve (use anti-seize or wrap with teflon tape to make removal easier). (iv) Remove the knock sensor on the starboard side of the engine block by removing the electrical connector to the knock sensor, and then carefully remove the knock sensor with the 7/8 wrench and let the water drain out. (v) Using a coat hanger, poke around and remove any obstruction in the block. 8) Remove Impeller. a) Unscrew the four brass screws on the raw water impeller housing and remove brass cover plate and gasket. b) Remove the raw water pump impeller by using the impeller puller. c) Lightly use Vaseline on the impeller shaft. d) Place screws, gasket and plate and lube old impeller with Vaseline and place all in zip lock bag and the old impeller is now a spare. e) Don t install new impeller and gasket until summarization. At summarization, lube up the new impeller with dish soap to make it easy to install. 9) Drain Heater Core. a) Remove the 1 diameter hose (input hose to heater core) from the barbed fitting at the engine block (same side as oil filter). Close the valve. b) Remove the 1 diameter hose (output hose from heater core) from the water circulating pump. c) Blow air (about 10 psi) in the input hose and blow the water out of the heater core which should drain from the outlet hose into the bilge. d) Leave the hoses disconnected until summarization and put hose clamps into zip lock bag. 10) Antifreeze Procedure (Optional and during engine fogging (Step 5 above). a) Put 4 gallons of 50/50 propylene glycol (environmentally friendly, generally pink) antifreeze in a 5 gallon bucket. Disconnect exhaust hoses from manifolds and plug one of the manifolds with a stopper. Put a hose from the other into the bucket, and then put a hose from the bucket to the inlet of the transmission cooler. (you re basically creating a loop where the antifreeze is being recirculated from the bucket, into the engine, and back into the bucket). b) Run the engine until it gets to operating temperature ( F). Run a couple minutes at temp to ensure coolant gets through the engine and the thermostat is in the full open position (if less that 140, the thermostat will remain closed and antifreeze will not fill engine cooling system). c) Stop engine & reconnect exhaust hoses to exhaust manifolds, but leave the intake hose in the bucket. d) Follow engine fogging procedure. Start engine and run it until ~ 2 inches of antifreeze are left in the bucket. Page 4 of 5
5 11) Engine Protectant. a) Spray all susceptible engine parts with engine protectant (bare metal, electrical connections, etc ). 12) Misc. Stuff. a) Loosen alternator belt to relieve tension. b) Lubricate rudder zirk fittings (two on the rudder stuffing box) and steering linkages. c) Tie zip lock bag with all the part to steering wheel for summarization. d) Remove battery and trickle charge once a month. e) Wash and wax boat. f) Clean vinyl and apply 303. g) Put boat cover. h) Tape down the exhaust flaps (keep critters out). B. Trailer Winterization. 1) Top off master cylinder with brake fluid. 2) Spray corrosion protectant on disc brake rotors. 3) Flush brake fluid master cylinder and brake lines every 2-3 years. 4) Fill bearing buddy s with grease. 5) Jack trailer off ground using jack stands to relieve pressure on sidewalls of tires, if possible. If not, over inflate tire pressure by 25% (recommended at Page 5 of 5
Epic 21/22 X22 Winterizing Procedure
Epic 21/22 X22 Winterizing Procedure Here is a visual overview of the winterization topics that are outlined in the Epic owners manuals. Refer to your manual for all necessary procedures First, hardware
More informationService Bulletin Winter Storage. All Carbureted Engines. 1. Stabilize Fuel. 2. Change Engine Oil and Filter 3.
Service Bulletin Volvo Penta of the Americas 1300 Volvo Penta Drive Chesapeake, Virginia 23320-9810 Distribution: M Date: 12-1996 Binder: C Group Number Version 17-3 5 02 Winter Storage All Gasoline Engines
More informationEdelbrock E-Force RPM Carburetor Supercharger C.I.D. Small-Block Chevy
Edelbrock E-Force RPM Carburetor Supercharger 302-400 C.I.D. Small-Block Chevy 1986 and Earlier Style Heads: 1513, 1514, 15131, 15133, 15141, 15143 E-Tec and Vortec Style Heads: 1515, 1516, 15151, 15153,
More informationStep 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
More informationCHEM-TEX POWER MAX 25 GOLD EDITION TRUCK MOUNT MANUAL
CHEM-TEX POWER MAX 25 GOLD EDITION TRUCK MOUNT MANUAL Congratulations On your purchase of a Power Max 25 Gold Edition Truck mount. The Power Max 25 Gold Edition are designed for the professional cleaning
More information***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe
***FOR COMPETITION USE ONLY as per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki Ultra 150 Triple Pipe Item Qty Part Number Part Description 1 1 COMASM0947 Ultra 150 PTO Chamber assembly
More informationHolley GM BBC Single-Plane EFI Intake Manifold Kits
Holley GM BBC Single-Plane EFI Intake Manifold Kits 300-561 Oval Port, 4150 Flange 300-562 Oval Port, 4500 Flange 300-563 Rectangular Port, 4150 Flange 300-564 Rectangular Port, 4500 Flange INSTALLATION
More informationInstallation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM
Installation Instructions for: TOYOTA 4.5L SUPERCHARGER SYSTEM 1995-1997 Land Cruiser * PREMIUM FUEL REQUIRED * Magnuson Products LLC 1990 Knoll Drive, Bldg A, Ventura, CA 93003 (805) 642-8833 phone *
More informationDisconnect the APP sensor harness connector. See Fig. 4. Remove the accelerator pedal mounting nuts. Remove the APP assembly.
ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION - 6.6L DIESEL... Page 1 of 41 FUEL SYSTEMS ACCELERATOR PEDAL POSITION SENSOR Removal & Installation Disconnect the APP sensor harness connector. See Fig.
More informationSection 10 Chapter 15
Section 10 Chapter 15 24 Valve, 8.3 Liter Engine Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New Holland warranty codes
More informationENGINE DEVELOPMENT INC.
2003 Ford Expedition 4.6L& 5.4L We encourage you to read this manual thoroughly before you begin work, and perform the following: 1. A quick parts check to make certain your kit is complete. If you discover
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More information7649A FUEL INJECTOR CLEANING SPECIALTY TOOLS USER MANUAL & REPLACEMENT PARTS LIST
7649A FUEL INJECTOR CLEANING SPECIALTY TOOLS USER MANUAL & REPLACEMENT PARTS LIST Safety Precautions WARNING: The following safety precautions must be carefully observed to reduce the risk of fire and
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications........................... 1B-1 Special Tools........................... 1B-2 Mercury/Quicksilver Lubricants
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More informationM-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS
!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. WARNING: CUSTOM CALIBRATION REQUIRED! CALIBRATION NOT INCLUDED! KIT CONTENTS: 1) Intake Manifold Assembly 2) Assembly
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More information1996 Aerostar/Ranger/Explorer
Page 1 of 11 Section 03-01B: Engine, 3.0L V-6 IN-VEHICLE SERVICE 1996 Aerostar and Ranger Vehicles Workshop Manual Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fan Clutch Holding
More informationENGINE COOLING GROUP CONTENTS RADIATOR GENERAL DESCRIPTION SPECIAL TOOLS THERMOSTAT
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOLS 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-4 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE 14-17 ENGINE
More informationLML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
More informationThermo-Bob 3 Installation Manual: KLR650E (2008 and newer)
Thermo-Bob 3 Installation Manual: KLR650E (2008 and newer) Thank you for purchasing the Thermo-Bob 3 radiator bypass system for the KLR650. Since the KLR already has a doohickey, it seemed that this thingamabob
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
TEST AND ADJUSTMENT Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking (Minimum).......................... 28 kpa (4 psi) Oil Pressure.....................................
More informationSection 10 Chapter 17
Section 10 Chapter 17 24 Valve, 8.3 Liter Engine Air Intake System Note: All coding used in the 8.3 Liter and 9 Liter engine manuals are Cummins engine codes. These engine codes have no meaning to New
More informationFord Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
More informationGas Engine overheat diagnosis
Gas Engine overheat diagnosis Introduction... 2 Six Step Troubleshooting Method... 3 Diagnostic Tips... 4 Clear Hose Testing Equipment... 5 Clear Hose Setup (Pump)... 6 Clear Hose Setup (Engine)... 7 Gauge
More informationParsun Portable 4-Stroke Outboard Motor Winterize or Storing DIY Service Guide
Parsun Portable 4-Stroke Outboard Motor Winterize or Storing DIY Service Guide To help keep your engine in tip-top condition for years to come, it is important that you winterize your outboard for off-season
More information*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki STX-R Triple Pipe
*** FOR COMPETITION USE ONLY per US EPA regulations *** Factory Pipe Bill of Materials Kawasaki STX-R Triple Pipe Item Qty Part Number Part Description 1 1 COMASM0935 STX-R PTO Chamber assembly 2 1 COMASM0936
More informationWEIAND X-CELerator Intake Manifold P/N 7516
WEIAND X-CELerator Intake Manifold P/N 7516 351C FORD, 2V CYLINDER HEADS INSTALLATION INSTRUCTIONS APPLICATIONS: The P/N 7516 X-CELerator intake manifold is designed for square-bore carburetor applications
More informationSPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS SPECIFICATIONS ENGINE FD620D, K SERIES
ENGINE FD620D, K SERIES SPECIFICATIONS SPECIFICATIONS TEST AND ADJUSTMENT SPECIFICATIONS Engine Oil Pressure Sensor Activates............................... 98 kpa (14.2 psi) Oil Pressure While Cranking
More informationHI-FLOW FUEL RAIL. Installation Instructions for: Part Numbers , ,
HI-FLOW FUEL RAIL Installation Instructions for: Part Numbers 25-100, 25-103, 25-112 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
More informationInstallation Manual v1.0: The Torque Pro Propane Injection System GM. Please read all instructions before installation.
PRO66-INST Installation Manual v1.0: The Torque Pro Propane Injection System GM Please read all instructions before installation. Thank you for purchasing the ATS Torque Pro Propane Injection System. This
More informationENGINE AND EMISSION CONTROL
17-1 GROUP 17 ENGINE AND EMISSION CONTROL CONTENTS ENGINE CONTROL........... 17-3 GENERAL INFORMATION....... 17-3 SERVICE SPECIFICATIONS..... 17-3 ON-VEHICLE SERVICE.......... 17-3 ACCELERATOR CABLE CHECK
More informationM-9424-M50CJ INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationEngine Removal / Installation Sea-Doo 800 RFI
Step 1 Battery and Seat Brace Removal Step 2 Intake Removal 2.1 (Below) Disconnect the head temp sensor wire, head cooling lines, and the lines to the rave valves. 2.4 (Below)Remove the four bolts securing
More informationWEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL
WEIAND INTAKE MANIFOLD P/N 7550 SMALL BLOCK CHEVROLET 3x2 BBL INTAKE MANIFOLD INSTALLATION INSTRUCTIONS 199R10703 APPLICATIONS: The P/N 7550 WEIAND intake manifold is designed for Holley 3x2 BBL, model
More informationGROUP CONTENTS GENERAL DESCRIPTION RADIATOR SPECIAL TOOL THERMOSTAT ENGINE COOLING DIAGNOSIS...
14-1 GROUP 14 CONTENTS GENERAL DESCRIPTION 14-2 SPECIAL TOOL 14-2 ENGINE COOLING DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES 14-4 ON-VEHICLE SERVICE
More informationRobert A. Reck II 3411 Saddle Drive Hayward, CA Phone
Robert A. Reck II 3411 Saddle Drive Hayward, CA. 94541 Phone 510-7279424 Chevrolet Blazer C/K ½ Ton - 4 Wheel Drive Utility 5.7/Liter Vin # 1GNEK18K7 PJ342553 New w/700 miles 05/15/93 13,500-10/01/93 air
More information96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions
96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove
More informationFREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
More information2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
More informationGENERAL INFORMATION 1 B MAINTENANCE
GENERAL INFORMATION 1 B MAINTENANCE Table of Contents Page Maintenance Schedules................... 1B-1 Maintenance Intervals.................. 1B-1 Scheduled Maintenance That Can Be Performed By Owner/Operator.........
More informationWEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P SMALL BLOCK CHEVROLET
APPLICATIONS: WEIAND STREET WARRIOR INTAKE MANIFOLD P/N s 8125, 8125P, 8126, & 8126P 262-400 SMALL BLOCK CHEVROLET INSTALLATION INSTRUCTIONS The P/N 8125 & 8126 WEIAND STREET WARRIOR series intake manifolds
More informationCoolant Temperature Switch; Black with Round Top and 4 Pin Connector $ $ Fuel Injector Insulator; O-Ring; Green
AC & Heater Control Valve; Mono Valve Solenoid Repair Kit 3065 1 $ 40.24 $ 40.24 Distributor Cap 03227 1 $ 88.73 $ 88.73 Distributor Rotor 04177 1 $ 19.86 $ 19.86 Vacuum Line, Transparent/Yellow, 1.0 X
More informationOwner smanual. Banks TorqueTube System. Jeep 2.5L 4-Cylinder '91-02 Wrangler. with Installation Instructions THIS MANUAL IS FOR USE WITH SYSTEM 51316
with Installation Instructions Owner smanual Banks TorqueTube System Jeep 2.5L 4-Cylinder '91-02 Wrangler THIS MANUAL IS FOR USE WITH SYSTEM 51316 Gale Banks Engineering 546 Duggan Avenue Azusa, CA 91702
More informationFUEL SYSTEM PRECAUTION FU 1
2GR-FE EL EL SYSTEM EL SYSTEM PRECAUTION 1 1. EXPRESSIONS OF IGNITION SWITCH (a) The type of the ignition switch used on this model differs according to the specifications of the vehicle. The expressions
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationOwner smanual. Banks torquetube System. Jeep 4.0L I-6 models including: Wrangler Cherokee Grand Cherokee Comanche
Owner smanual with Installation Instructions Banks torquetube System Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS MANUAL IS FOR USE WITH SYSTEM
More information2015 WRX Engine Oil Cooler
2015 WRX Engine Oil Cooler 2014-04-24 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More informationPOST-REBUILD PREPARATIONS AND START-UP PROCEDURE FOR INDIAN WARRIOR
POST-REBUILD PREPARATIONS AND START-UP PROCEDURE FOR INDIAN WARRIOR This procedure assumes the engine and gearbox are assembled properly and with assembly lube, installed in the bike frame, the electrical
More informationWJ JACUZZI ENERGIZER PARTS LIST
WJ JACUZZI ENERGIZER PARTS LIST BAG KIT QTY PART # DESCRIPTION ITEM CK. 1 B-1007 THRUST BEARING 8 F20LW LOCKWASHER, 5/16 8 F21CS HEX HEAD CAP SCREW, 5/16-18 X 1-1/4 1 K-4007 SHIM KIT W / 3 EXTRA.060 SHIMS
More informationOwner smanual. Banks TorqueTube System With Optional Headpipe Assembly
Owner smanual with Installation Instructions Banks TorqueTube System With Optional Headpipe Assembly Jeep 4.0L I-6 models including: 91-99 Wrangler 91-99 Cherokee 93-98 Grand Cherokee 91-92 Comanche THIS
More informationFuel Pressure Regulator Kit PART# - RY12040-RRFPR-6S5
APPLICATION(S): Yamaha FX-SHO, FZR & FZS Fuel Pressure Regulator Kit PART# - RY12040-RRFPR-6S5 We strongly recommend the use of a service manual to familiarize yourself with the various components and
More informationPhone Fax
Directions for Installation of ECS Paxton Supercharger Kit Disconnect battery Remove stock serpentine belt Remove stock belt tensioner, save the 2 bolts for later use on supercharger bracket Remove alternator
More informationSECTION 4 - FUEL/LUBRICATION/COOLING
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning
More informationCorrado Club of Canada. VR6 Engine FAQ. By: Dennis
Corrado Club of Canada VR6 Engine FAQ By: Dennis I thought I would snap a few pics of the engine compartment on my 1994 VR6 Corrado. First, this is the updated engine management system so it does have
More informationTS-L 1000 (98MCC-1998) Page 1 of 69 BILGE PUMP ASSEMBLY
1998 TS-L 1000 (98MCC-1998) Page 1 of 69 BILGE PUMP ASSEMBLY 1998 TS-L 1000 (98MCC-1998) Page 2 of 69 BILGE PUMP ASSEMBLY 1 0673-377 1 Fitting, Outlet - Bilge 2 0612-456 2 Seal, Fitting 3 0623-753 2 /P
More informationINTAKE SWAP INSTRUCTION MANUAL 1.Items to pick up before you begin:
INTAKE SWAP INSTRUCTION MANUAL 1.Items to pick up before you begin: Someone to lend you a hand for about 10 minutes Intake gasket set that pertains to your year of engine Coil of your choice Spark plugs
More informationENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT...
14-1 GROUP 14 CONTENTS GENERAL INFORMATION 14-2 SERVICE SPECIFICATIONS 14-2 COOLANT 14-3 SEALANT 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES
More informationENGINE COOLING SYSTEM
B ENGINE A SECTION ENGINE COOLING SYSTEM CO C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 Precautions for Liquid Gasket...
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More informationInstant Chat off the main page of Or simply call our tech team at
Subaru WRX/STI Air Oil Separator for Front Mounted Intercooler Setups 2013-02- 22 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons
More informationIMCO SCX SERIES INFORMATION, OPERATION & MAINTAINANCE
IMCO SCX SERIES INFORMATION, OPERATION & MAINTAINANCE Warning! Warning! Warning! Danger! Warning! 1. SCX & SCX4 Drives will not fit on a standard gimbal helmet, IMCO HELMET: #05-8025 Black or #05-8027
More informationA SYSTEMATIC SEQUENCE FOR PM INSPECTIONS
A SYSTEMATIC SEQUENCE FOR PM INSPECTIONS TYPE OF INSPECTION UNDER THE HOOD GASOLINE AND DIESEL 1 Fuel, oil, exhaust leaks - inspect 2 Oil and fuel lines inspect for kinks and wear 3 Automatic transmission
More informationEdelbrock Enforcer EFI Supercharger C.I.D. Small-Block Chevy
Photo may not represent actual product. 302-400 C.I.D. Small-Block Chevy 1986 and Earlier Style Heads: 1520, 1521, 15201, 15211, 15203, 15213 E-Tec and Vortec Style Heads: 1522, 1523, 15221, 15231, 15223,
More informationEXHAUST GAS RECIRCULATION (EGR) SYSTEM (4A FE)
ENGINE EG121 EXHAUST GAS RECIRCULATION (EGR) SYSTEM (4AFE) EGR SYSTEM INSPECTION 1. INSPECT AND CLEAN FILTER IN EGR VACUUM MODULATOR (a) Remove the cap and filter. (b) Check the filter for contamination
More informationProperty of American Airlines
MH Utility Vehicle Section 3 SECTION 3: SPECIFICATIONS AND CAPABILITIES A. DIMENSIONS 1. Length, Excluding Coupler... 153 inches (389 cm) 2. Width, Overall... 78 inches (198 cm) 3. Height, Overall... 78
More information2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
More informationENGINE AND EMISSION CONTROL
-1 ENGINE CONTROL.......... GENERAL INFORMATION...... SERVICE SPECIFICATIONS..... ON-VEHICLE SERVICE......... ACCELERATOR CABLE CHECK AND ADJUSTMENT.................... ACCELERATOR CABLE AND PEDAL......................
More informationPrerequisites: Shop Manual (recommended) pages 3-9 through 3-13.
Prerequisites: Order your gaskets average about $25.00 bucks X 2 so $50.00 4NK-11193-00-00 Obtain a shim kit (Should have several 265 and 270s) (Some dealers will exchange) Obtain a Valve Bucket Tool YM-33961
More informationCLEANERS AND DEGREASERS LUBRICANTS
CLEANERS AND DEGREASERS ENGINE CLEANER AND DEGREASER Solvent-based formula Quickly dissolves grease, oil and tar from engines and equipment Spray on, rinse off with water SP4220 20 oz. can Net wt. 14.5
More informationIMPORTANT INFORMATION
Table of Contents IMPORTANT INFORMATION Section 1B - Maintenance MAINTENANCE 1 B Specifications................................ 1B-1 Special Tools................................ 1B-2 Quicksilver Lubricant/Sealant..................
More information5-2 FUEL SYSTEM AND THROTTLE BODY FUEL SYSTEM FUEL DELIVERY SYSTEM The fuel delivery system consists of the fuel tank, fuel pump, fuel filters, fuel f
FUEL SYSTEM AND THROTTLE BODY 5-1 FUEL SYSTEM AND THROTTLE BODY I CONTENTS FUEL SYSTEM 5-2 FUEL DELIVERY SYSTEM 5-2 FUEL PUMP 5-3 FUEL PRESSURE REGULATOR 5-4 FUEL INJECTOR 5-4 FUEL PUMP CONTROL SYSTEM
More informationTECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:
TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: 2007 2008 IS 350: 2006 2008 I. OPERATION FLOWCHART Verify Vehicle Eligibility 1. Check the VIN range. 2.
More informationAEROMOTIVE Part # Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14137 04-06 Subaru STI Fuel Rail Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend
More informationAEROMOTIVE Part # Subaru Fuel Rails for Top Feed Injectors WRX & STI INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 14135 Subaru Fuel Rails for Top Feed Injectors 02-14 WRX & 07-14 STI INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems
More informationEngine Removal / Installation Yamaha 650 / 701X
Step 1 Battery Removal 2.1 (Below) Remove the flame arrestor screen. 2.3 (Below) Loosen the gas tank cap to relieve pressure. Be sure the fuel switch is turned to the OFF position, and be aware of any
More informationOil Cooler Thermostat for GM LS Series Engines, Rear Sump
Oil Cooler Thermostat for GM LS Series Engines, Rear Sump Part No. EGM-112 Made in USA IMPORTANT: Please read these instructions in their entirety prior to installation. Rev 180412 Applications 1997+ aluminum
More informationCome Experience The Allen Gwynn Difference
Come Experience The Allen Gwynn Difference No Fluff, No Fancy, No Gimmicks We service all GM makes & models regardless of where you purchased your vehicle Factory-trained Technicians for all GM cars ASE-Certified
More information14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE
14-6 RADIATOR CAP DRAIN PLUG ENGINE COOLING ON-VEHICLE SERVICE When removing the radiator cap, use care to avoid contact with hot coolant or steam Place a shop towel over the cap and turn the cap counterclockwise
More informationAEROMOTIVE Part # & ½ L DOHC Return Style Fuel System Kit INSTALLATION INSTRUCTIONS
AEROMOTIVE Part # 17145 & 17146 98 ½-04 4.6L DOHC Return Style Fuel System Kit INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair
More informationENGINE COOLING GROUP CONTENTS GENERAL INFORMATION SERVICE SPECIFICATIONS COOLANT SEALANT THERMOSTAT...
14-1 GROUP 14 CONTENTS GENERAL INFORMATION 14-2 SERVICE SPECIFICATIONS 14-2 COOLANT 14-3 SEALANT 14-3 DIAGNOSIS 14-3 INTRODUCTION 14-3 TROUBLESHOOTING STRATEGY 14-3 SYMPTOM CHART 14-3 SYMPTOM PROCEDURES
More informationMerCruiser & Mercury Diesel Logbook R02
MerCruiser & Mercury Diesel Logbook 90-889160R02 04/2015 IMPORTANT Maintenance must be completed by a Mercury Marine/Brunswick Marine in EMEA authorized dealer. At the completion of any maintenance check-up
More informationCrawford Performance Top Mount Air/Oil Separator Version 2 (S0714-1)
Crawford Performance Top Mount Air/Oil Separator 02-07 Version 2 (S0714-1) Parts List Part Number Quantity Description Sent Received S0707-1 1 TMIC Air/Oil Separator V2 F0365 1 Crank Case Breather Connector
More informationInstallation Instructions Part Number
Installation Instructions Part Number 84152143 Thank you for choosing Chevrolet Performance as your high performance source. Chevrolet is committed to providing proven, innovative performance technology
More informationWEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
More information1988 Ford F-350 PICKUP
1988 Ford F-350 PICKUP Submodel: Engine Type: V8 Liters: 7.5 Fuel Delivery: FI Fuel: GAS 1987 93 4.9L Engine The intake and exhaust manifolds on these engines are known as combination manifolds and are
More informationDisconnect the breather tube from the air cleaner outlet duct.
Disconnect the breather tube from the air cleaner outlet duct. Disconnect the IAT sensor harness connector. Remove the air cleaner outlet duct retaining wingnut. Separate the air cleaner outlet duct from
More informationFULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L
2018-01-15 FORD F150 ECOBOOST 3.5L FULL BORE PERFORMANCE MANIFOLD SET (PART #500101X) 1 FULL BORE PERFORMANCE EXHAUST MANIFOLDS F-150 ECOBOOST 3.5L INSTALLATION INSTRUCTIONS 2011-2012 FORD F150 3.5L ECOBOOST
More informationWRX/STI Engine Oil Cooler
2002-14 WRX/STI Engine Oil Cooler 2014-04-21 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationVW (Engine Code CJAA/CBEA) 2.0 Liter TDI Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service
VW (Engine Code CJAA/CBEA) 2.0 Liter TDI Diesel EGR Cleaning Instructions Always wear gloves and safety glasses when performing this service EGR System Consists of: 1 Hot side EGR valve (no EGR cooler),
More informationCummins 6.7 Litre 2500/3500 Diesel EGR System. Always wear gloves and safety glasses when performing this service
Cummins 6.7 Litre 2500/3500 Diesel EGR System Always wear gloves and safety glasses when performing this service EGR System Consists of: Cold side EGR valve (after EGR cooler) controls exhaust gases for
More informationBMW/Isuzu 3.0 Liter Diesel EGR Cleaning Instructions
BMW/Isuzu 3.0 Liter Diesel EGR Cleaning Instructions EGR System Consists of: 2 Cold side EGR valves (after EGR coolers), high pressure loop and a low pressure loop which controls exhaust gases for proper
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST
1/6/04 1501 Industrial Way N., Toms River, NJ 08755 732-349-2109 Fax:732-244-0867 MODERATE - Installation requires metric tools and possibly cutting and drilling. The ability to closely follow instructions
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More informationIN-VEHICLE SERVICE. Engine Components
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk31a14.htm~gen~ref.htm Page 1 of 10 Section 03-01A: Engine, 2.3L I-4 IN-VEHICLE SERVICE 1997 Ranger Workshop Manual Engine Components The views shown
More informationCAUTIONS AND WARNINGS
FIREWALL FORWARD FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More information