ECS Tuning 3095 Cleveland-Massillon Rd. Norton, Ohio Phone Fax Web
|
|
- Adam Craig
- 5 years ago
- Views:
Transcription
1
2 B7 A4 Gauge Pod Installation Instructions Safety first:. When working with your vehicles electrical system; always disconnect the battery! Avoid shorting any circuits, or probing around wires. Failure to follow these safety precautions, and all others, could result in irreversible damage to your vehicles electrical system, failure to start, fire, and/or personal injury. Before you undertake this installation, it is important that you read the following instructions! Listed below are the necessary tools and skills required to complete the job. If the installation of this product seems overwhelming, please contact a qualified installer in your area. Be aware that disconnecting your battery may require you to input your radio anti-theft code, so make sure you have it handy. Estimated Installation Time: 1-2 Hours Tools Required: Small Flat Head Screw Driver #2 Flat Head Screw Driver T-30 Torx T-25 Torx T-20 Torx 8mm Socket 10mm Socket 13mm Socket Socket Wrench Drill ¼ Inch Drill Bit 9/16 Inch Drill Bit Razor Blade Tape Work Light
3 Preparation: Park automobile on a level, suitable working area. Be sure to put the vehicle in park and/or engage the parking brake. Allow the engine time to cool to ambient temperatures to avoid the possibility of burns. Start the installation by removing the center vent assembly from the dashboard. Using a flat head screw driver, or plastic tool, carefully extract the center vent assembly and remove from vehicle.
4 With the vent assembly removed, remove the front trim ring. The front trim ring is easily removed by depressing several small tabs that hold it in place and pulling it off.
5 Remove the horizontal vent slats. Remove the vertical vent slats.
6 Drill two 9/16 holes in the bottom of the vent assembly. Place the two larger supplied grommets into these holes. The boost gauge harness will later route through these holes. ECS Tuning 1000 Seville Rd. Wadsworth Ohio, Phone Fax Web
7 Begin working inside the vehicle by first removing the fuse panel cover and lower dash panel on the driver s side of the vehicle. This can be done by removing the 8mm bolts holding it in place and applying firm pressure to pull the panel from the dashboard. Then, unclip the foot well light and OBD2 connector from the panel and set aside. ECS Tuning 1000 Seville Rd. Wadsworth Ohio, Phone Fax Web
8 Begin working inside the vehicle by first removing the fuse panel cover and lower dash panel on the driver s side of the vehicle. Disconnect the fuse panel by the two 8mm bolts. Disconnect the back of the fuse panel by the two clips on the side of the fuse block. ECS Tuning 1000 Seville Rd. Wadsworth Ohio, Phone Fax Web
9 Locate the solid black wire on the back of the fuse panel. This will be fuse #47 located on the other side of the fuse panel. Using a scotch lock provided in the kit attach the red wire from the gauge wiring harness. ECS Tuning 1000 Seville Rd. Wadsworth Ohio, Phone Fax Web
10 Locate the head light switch wire harness and disconnect it. Connect the green and black wire from the gauge harness to pin number 10 on the head light switch harness(brown wire). Connect the white wire to pin number 17 on the head light switch harness(gray wire with blue trace). This completes the wiring of the gauge. The routing of the wiring harness up to the gauge pod is discussed later in these instructions. ECS Tuning 1000 Seville Rd. Wadsworth Ohio, Phone Fax Web
11 Next, remove the engine cover under the hood. Locate the circled cap. Cut the OEM crimp clamp holding the cap on the intake manifold. Remove cap
12 Install the supplied ECS Billet Boost T as shown in the above picture with supplied piece of hose. Connect the Boost T to the boost line using a 2 piece of included vacuum line.
13 Route the boost line as demonstrated in the above picture. Drill a 1/4 hole in the circled grommet. Feed the boost line into the rain tray as shown. Next, start removing the T-30 Torx screws holding the Ecu lid down.the last screw is accessible, once the driver side windshield wiper arm has been removed.
14 The last screw (T-30) is removed as demonstrated in the above picture. Using a ¼ inch drill bit, proceed to drill a hole in the side of the ecu compartment as shown in the above picture. The smaller supplied grommet goes here to prevent any water from entering the ecu compartment.
15 Route the boost line as shown down into the drivers compartment. Once the boost line has been routed to your satisfaction, reinstall the ecu, ecu compartment lid, and windshield wiper. phone Fax Web
16 Route the boost line down the inside of the fire wall as shown in the above picture. Continue routing the boost line towards the boost sensor.
17 Connect the end of the boost line to boost sensor. With the two supplied screws securely fasten the boost sensor underneath the dashboard out of the way of moving parts. Continue to rout the wire from the boost sensor to the gauge behind the vent. Phone Fax Web
18 Insert the boost gauge into the ECS vent pod, and connect the two plugs into the back of the gauge. Reinstall lower dash panel, insuring all wires and lines are out of the way of moving parts. Secure any loose wires or lines with included zip ties.
19 This completes the installation of the ECS Tuning vent gauge pod.
MKV Jetta OEM Fog Installation Instructions
Installation Procedures MKV Jetta OEM Fog This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the
More informationfor Audi B7/A4 ( ) Part Number ES8017 Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationForge 004 Dual Sprung Blow Off Valve Installation Instructions
Installation Procedures Forge 004 Dual Sprung Blow Off Valve This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationDODGE RAM 24V 5.9L CUMMINS
DODGE RAM 24V 5.9L CUMMINS DODGE RAM 24V 5.9L CUMMINS TABLE OF CONTENTS SECTION 1 Preparing the Installation 1 SECTION 2 Boost Gauge Installation 2 SECTION Pyrometer/EGT Gauge Installation 4 SECTION 4
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593109) for VW
More informationAccessory Fuse Block. Please read this entire manual before proceeding with installation.
Accessory Fuse Block Please read this entire manual before proceeding with installation. Kit Components: (1) Fuse Block Assembly (1) Harness (1) Positive power cable (1) Negative power cable (5) Pigtails
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B6 A4 (2002-2004) Proper service and repair procedures
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More informationECS R32 Exhaust Flap Manual Override Installation Instructions
Installation Procedures This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of
More informationIntake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter)
Intake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter) Year/Make/Model/Engine 2012-17 Ford Focus 2.0L Parts List 1- Intake tube 1- Heat shield, Side 1-
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationBremmen Automatic Headlight Conversion Kit Installation Instructions
Bremmen Automatic Headlight Conversion Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationMKVI Jetta Fog Light Kit
MKVI Jetta Fog Light Kit Part Number VW Jetta Fog Light Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More informationNissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
More informationVolkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions
Volkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More information2010+ VW Mk6 2.0T Vent Boost Gauge Kit INSTALLATION GUIDE
INSTALLATION GUIDE 2010+ VW Mk6 2.0T Vent Boost Gauge Kit Congratulations on your purchase of the AWE Tuning Vent Boost Gauge Kit for the 2010+ VW Mk6 2.0T. Exquisite build quality with industry leading
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationIT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.
Instructions for Universal Harness PRINT THESE INSTUCTIONS Gentex Mirror Installation Instructions Provided by www.rearviewautomirrors.com These instructions have been prepared to provide you with details
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 PILOT Publications No. AII 43339-47543 Issue Date JAN 2012 PARTS LIST Trailer Harness Kit P/N 08L91-SZA-100 Towing Kit P/N 08L92-SZA-100 Ball mount
More informationvacuum/boost vent mounted ES best viewed in Acrobat Reader This tutorial is provided as a courtesy by ECS Tuning.
vent mounted vacuum/boost ES2713030 This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-100 Application 2008 ACCORD 2-AND 4-DOOR Publications No. AII 35358 Issue Date AUG 2007 PARTS LIST Ambient Light Kit 2 Ambient lights Fuse label Washer
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39889 HITCH 2009 MDX Issue Date JULY 2008 PARTS LIST Trailer Hitch Kit P/N 08L92-STX-200 Trailer Harness Kit P/N 08L91-STX-200 Trailer
More informationES Installation Instructions. best viewed in Acrobat Reader. This tutorial is provided as a courtesy by ECS Tuning.
Installation Instructions This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of all engine
More informationINSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT
INSTALLATION INSTRUCTIONS BILLET FUEL RAIL KIT MITSUBISHI LANCER EVOLUTION X Document# 19-0067 Support: info@radiumauto.com WARNING: DON'T SMOKE OR WORK WITH OPEN SPARKS WHILE WORKING ON THE FUEL SYSTEM
More informationAudi B5 A4/S4 B6 A4 APR Performance Chip Tune ECU Removal and Installation
Audi B5 A4/S4 B6 A4 APR Performance Chip Tune ECU Removal and Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2009 PILOT Publications No. AII 39422 Issue Date MAY 2008 PARTS LIST Trailer Harness Kit P/N 08L91-SZA-100 Sold Separately Trailer socket harness Control
More informationTools you will need: Screwdrivers, Metric Sockets, Hook and Loop Tape or Zip Ties, Shop Light, Wire cutters, Wire crimping tool
Overview: This guide provides instruction for installing Adventure Wagon s Auxiliary Battery Tray and the charging bundle. Package Contents: Adventure Wagon Battery Tray includes the tray plus mounting
More informationThis harness kit includes: Civic harness (2003 to 2005) Installing the Hybrid ReVolt Universal grid charger in a First Gen Civic ( )
Installing the Hybrid ReVolt Universal grid charger in a First Gen Civic (2003-2005) This harness kit includes: Civic harness (2003 to 2005) (a) 1 HV warning label (c) 1 charger connector cover (e) 4 #6
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SECURITY SYSTEM P/N 08E49-SDA-100 ACCORD 2- AND 4-DOOR AII 30666 Issue Date AUG 2005 PARTS LIST Hood switch harness Illustration of the
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE ENGINE STARTER SYSTEM Application 2010 CIVIC 4-DOOR Publications No. AII 42460 Issue Date AUG 2009 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationRecommended tools: Estimated install time: Parts list:
Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi A4/S4. While the install is fairly straight forward, please review these instructions carefully before attempting
More informationRaxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler)
Raxiom Factory GPS Rear Back-up Camera Kit (07-17 Wrangler) Installation Time: 2.5-3Hrs Tools Required: 7mm Socket & Driver 10mm Socket 10mm Open end wrench Knife / Razor blade Zip-ties Wire Cutters Needle
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. Remote Engine Starter Attachment Kit P/N 08E92-SNA-100B
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REMOTE ENGINE STARTER SYSTEM 2008 CIVIC 2-DOOR AII 38215 Issue Date OCT 2007 PARTS LIST Remote Engine Starter Unit Kit P/N 08E91-E22-100B
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TK6-100 Application 2013 FIT Publications No. AII 13198 Issue Date JULY 2012 PARTS LIST Ambient light kit 2 Ambient lights 6 Wire ties Fuse label 2 Grommets
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08E10-TA0-110A Application 2012 ACCORD 2- AND 4-DOOR Publications No. AII 46501 Issue Date AUG 2011 PARTS LIST Ambient Light Kit Fuse label 2 Ambient lights Washer
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS
GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS PART NUMBERS: APPLICABLE MODELS: 0000-89-G14A (PORT) Electrochromic Mirror Kit w/ Compass/Temp/HomeLink 2004 Mazda 3 0000-8C-G14A (PDC) KIT CONTENTS: ITEM
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC All 30175-31616 2 AND 4-DOOR P/N 08E10-SNA-100 Issue Date DEC 2005 NOTE: The interior illumination lights cannot be installed on 2-door
More information05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050
05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050 Note: Read installation instructions before starting. Component Check List: Quantity/Description Part# CDC Installer 2 - Squirter Nozzles 115063
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 PILOT Publications No. AII 43339 Issue Date MARCH 2010 PARTS LIST Trailer Harness Kit P/N 08L91-SZA-100 Towing Kit P/N 08L92-SZA-100 Ball mount Trailer
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationGentex Homelink Installation Instructions
Gentex Homelink Installation Instructions Kit Contents: Item Qty Part Description 1 Number GENK-41 NVS Homelink Mirror GENK-42 NVS Homelink w/mood lights 1 of the GENK-45 NVS Homelink w/compass following
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39890 2009 MDX Issue Date JULY 2008 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-STX-200A Self-tapping screw, 5 x 16 mm 12 Wire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationLethal Performance Dual FPDM Harness Kit Installation
Lethal Performance Dual FPDM Harness Kit Installation The Lethal Performance Dual FPDM Harness Kit is a plug-and-play modification. Depending on whether you are using the Lethal Performance wire upgrade
More information6945 (12v) 6944 (24V) installation instructions
6945 (12v) 6944 (24V) installation instructions included: tools needed: Cordless drill Breezeeasy Fan Mounting brackets 1/4 Drill Bit 10mm Socket Hardware Pack 10mm Wrench Fuse Assembly Wire Stripper Crimper
More information05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050
CD4II3BC 05 09 Mustang Squirter Nozzle Relocation Kit CDC #112050 Note: Read installation instructions before starting. Component Check List: Quantity/Description Part# CDC Installer 2 - Squirter Nozzles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 37978 XM RADIO SYSTEM 2008 CIVIC HYBRID Issue Date SEP 2007 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SNA-100B 7 Wire
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationInstallation instructions, accessories. Electric engine block heater, connector outlet, 4-cyl
Installation instructions, accessories Instruction No 31359444 Version 1.2 5 Part. No. 31359438 Electric engine block heater, connector outlet, 4-cyl IMG-247665 Volvo Car Corporation Electric engine block
More information2015 Mustang Lightbar (All Models) CDC#
2015 Mustang Lightbar (All Models) CDC# 1511-7000-01 Components: 1 CDC Lightbar Note: READ instructions before starting installation!!! CDC Part# Driver side bracket 0511-6001-05 Passenger side bracket
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AUTOMATIC AII 27160 2005 CR-V Issue Date ATTACHMENT KIT SEP 2004 PARTS LIST Automatic Day/Night Mirror Attachment Kit (sold separately)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TP6-100 Application 2010 ACCORD CROSSTOUR Publications No. AII 41935 Issue Date NOV 2009 PARTS LIST TOOLS AND SUPPLIES REQUIRED Ambient Light Kit Ambient
More information2.0 FSI Quick Spool Crank Pulley Installation Instructions
Installation Procedures 2.0 FSI Quick Spool Crank Pulley This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2011 PILOT Publications No. AII 43298 Issue Date MARCH 2010 PARTS LIST Back-up Sensor Attachment Kit P/N 08V67-SZA-100A Back-up sensor harness Fuse label
More informationVolvo P1 Air Intake. ELEVATE Turbo Intake Pipe. MAF Sensor. Inlet Manifold. Air Filter Housing. ECU Cover
Volvo P1 Air Intake Tools needed: 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 8mm Combination Wrench and/or Socket with Ratchet 10mm Combination Wrench and/or Socket
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit was designed for a standard single pump Radium Engineering
More informationSCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4
Section I Installation Preparation 2.4L I-4 Part Number(s): PTR03-52110 Kit Contents Item # Quantity Description Reqd. 1 1 TRD Inlet Tube 2 1 TRD Upper Air Box with HC Trap 3 1 Hump Hose Coupler 4 1 Hump
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 30230 2006 RSX P/N 08U96-S6M-200 Issue Date JULY 2005 PARTS LIST Cigarette lighter 3. Turn the two knobs counterclockwise, and remove
More informationSAFETY. Read and understand all safety precautions and instructions before installing this product.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. 2010 CIVIC All 42479 2- AND 4-DOOR P/N 08E10-SNA-110 Issue Date AUG 2009 NOTE: The interior illumination lights cannot be installed on 2-door
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25877 PILOT Issue Date AUG 2003 Optional ATF and power steering coolers are required when installing the trailer hitch. 2 Spacers PARTS
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationAudi B6/B7 A4/S4/RS4 Refrigerated Glove Box Kit. Part Number ES This tutorial is provided as a courtesy by ECS Tuning.
Part Number Audi B6/B7 A4/S4/S4 efrigerated Glove Box Kit This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor
More informationR53 BOOST GAUGE INSTALL
R53 BOOST GAUGE INSTALL 052009 Thank you for purchasing the ALTA Performance gauge pod. Installation should only be performed by persons experienced in the proper operation of Mini electrical and body
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REMOTE CONTROL Application 2008 CR-V Publications No. AII 35843-38422 Issue Date DEC 2007 PARTS LIST Caution label Remote Engine Starter Kit P/N 08E91-E22-100B Transmitter
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationAudi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions
Audi B8 19Z Caliper 380mm Rotor Front Big Brake Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2013 MDX Publications No. BII 13442 Issue Date JULY 2012 PARTS LIST Receiver cover Trailer hitch Hitch pin Left bracket Hitch pin clip Trailer Harness
More informationFocus ST Carbon Fiber Intake
791400 - Focus ST Carbon Fiber Intake 791400 COBB Focus ST Carbon Fiber Intake Congratulations on your purchase of the COBB Tuning Carbon Fiber Intake System! The following instructions will assist you
More informationSCION tc FOG LIGHT. Part Number: STC-312 / STC-812
SCION tc 2011-2013 FOG LIGHT Part Number: STC-312 / STC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness
More informationPart Number: TAV-713 TOYOTA AVALON LED DRL
Part Number: TAV-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion pad 6 1 Switch 7 2 Drill Jigs Hardware Bag Contents
More informationINSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT
INSTALLATION INSTRUCTIONS AIR/OIL SEPARATOR KIT 2015+ SUBARU WRX (LHD ONLY) Document: 19-0136 Support: info@radiumauto.com This document covers the installation of the Radium brake master cylinder brace
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM P/N 08E60-SLN-100 2007 FIT AII 31719 Issue Date MAR 2006 PARTS LIST Fuse label B Keyless entry harness User s information Fuse label
More informationHayes TrailTrac Kit Installation Guidelines Polaris Rush / Pro-R / Indy
Models: 2010-2014 Polaris Rush / Pro-R / Indy Packing List 1 Electronic Control Unit (ECU) 1 ECU Velcro, 3 inch 1 Switch face plate 1 Switch face plate adhesive 1 Switch 1 Wiring harness 1 Fully pre-filled
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALLATION KIT 1999-2006 BMW E46 COUPE Document# 19-0056 Support: info@radiumauto.com Note: This kit wasn t designed for a FST-R, but can be accomplished. 1.
More informationOEM Cruise Control Installation in GMC/Chevy NBS trucks
OEM Cruise Control Installation in 99-02 GMC/Chevy NBS trucks May 2008 ~ Rampage_Rick Having just installed factory cruise control in my 00 Sierra, I thought I d share the fun. I followed the steps outlined
More informationM7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301
M7 R52S & R53 Cold Air Intake Installation Guide 53-3M7301 M7 Speed engineers and manufactures the highest quality MINI COOPER accessories and performance parts available anywhere on Planet Earth! Please
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. (Trunk Mount) 2009 CIVIC 4-DOOR AII 40184 Issue Date AUG 2008 PARTS LIST 8 Cushion tapes Changer Attachment (Sold Separately) P/N 08B26-SNA-101
More informationfile://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...
Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:
More informationWeistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
More informationJames Barone Racing Focus ST Transmission Mount Installation Instructions
Page1 James Barone Racing 2013+ Focus ST Transmission Mount Installation Instructions What you will need: Jack and jack stands. (Jack stands are preferred) o Ramps will work but, the job will be much more
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08E10-TK8-100 Application 2011 ODYSSEY Publications No. AII 43904 Issue Date SEP 2010 PARTS LIST 2 Ambient lights Illustration of the Ambient Lights Installed
More information