Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
|
|
- Ashlee Bradley
- 6 years ago
- Views:
Transcription
1 Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B6 A4 ( ) Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WAANTY OF MECHANTABILITY, FITNESS FO A PATICULA PUPOSE O ANY OTHE WAANTY IS MADE O TO BE IMPLIED WITH ESPECT TO THIS MATEIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.
2 VW MKVI Golf/GTI Vent Pod Vacuum/Boost Gauge Installation Kit Contents: vacuum/boost gauge with o-ring gauge power harness vacuum/boost sensor (transducer with integral harness) gauge vent pod vacuum tee moisture filter rigid plastic vacuum line rubber hose bullet connectors crimp clamps zip ties Tools crimping tool (end nippers) side cutters (diagonal cutters) non-marring trim removal tool electric drill with ½-inch drill bit ratchet with 8mm socket and short extension wire stripper/crimper common screwdriver X-ACTO knife (or similar) work light sharp hole punch Make the job easier and prevent damage to headliners and other interior trim with ECS Tuning Trim and Molding emoval Tool Sets: ES and ES The gauge in your kit is used for several applications. The box it comes in contains parts not used in this application (and not shown above), including a u-shaped mounting bracket, brass threaded attachment studs, two screws, a plastic vacuum tee, and insulated spade connectors. (Throw them in your tool box for another project.) Page - 2
3 crimper ECS Tuning Vent Pod Vacuum/Boost Gauge Kit Electrical Connections Your kit contains both bullet style and butt connectors. Use the bullet connectors to splice the gauge power harness into the light switch harness. Directions below show how to use the connectors. Using crimp connectors 1) Cut the headlight harness wire you want to tap into. emove enough insulation from both lengths of wire to expose a short length of wire (about 3/8-inch). 1 headlight harness wire 2 3 2) Insert the two lengths of bared wire into the female bullet connector. Insert the correct matching wire from the gauge harness into the male bullet connector. gauge power harness wire 3) Using a crimping tool, crimp the connector ends enough to squeeze the bare wire securely. Do not over-crimp, or you may damage the insulating collar. Note: Use a suitable wire stripper that will remove the insulation without cutting away wire strands. Use a crimping tool of the correct size, not side cutters or other pliers that may damage the insulation on the connectors. 4 4) Plug the two ends together. Make sure they are fully engaged. epeat this process on the remaining wires at the headlight harness. mm mm insul wire cutter non insul wire stripper See page 9 for a schematic showing component locations, electrical connections, and wire colors. Page - 3
4 Overview - How the tutorial is organized This tutorial is broken into two sections: 1) un the Vacuum Line - This section describes how to connect the vacuum tee at the intake manifold, and how to route the plastic vacuum line from the tee to the vacuum transducer inside the cabin. 2) Install the Vent Pod and Gauge - This section shows how to disassemble the dashboard vents, install the vent pod and vacuum/boost gauge, and splice the wiring. Section 1 - un the vacuum line to the transducer In this section we will connect the vacuum/boost sensing line to a vacuum source at the intake manifold, and then run the line through the firewall, into the cabin area beneath the dash. Use the schematic below to identify major component locations and hose routing. The photos on the following pages show how to: boost sensing transducer Insert the vacuum tee in the vacuum line at the intake manifold. Connect the tee to the long length of plastic line using a short length of braided vacuum hose. oute the plastic vacuum line from the engine compartment to the grommet in the firewall. oute the plastic vacuum line through the firewall grommet into the cabin, below the dashboard. Connect the moisture filter and vacuum/boost pressure transducer to the plastic vacuum line, using short lengths of braided vacuum hose. computer box hood release cable grommet wire harness to boost gauge moisture filter The vacuum tee, plastic line, clamps, and braided rubber hose are all included in your kit. Use the zip ties to secure all lines and hoses safely away from moving components, like pedals and the steering mechanism. Page - 4
5 Section 1 - un the Vacuum Line - Install the Transducer Step 1 - Under the hood- Install the vacuum tee. Open the hood. Locate the vacuum line located at the left rear of the intake manifold. (For reference, the hose is close to the coolant recovery bottle.) Cut the hose, as shown. Step 2 - Under the hood- Install the vacuum tee. Slide one crimp clamp over each length of hose and insert the vacuum tee between the hoses. When the tee is properly positioned, use the end nippers to crimp the clamps tight. (We prefer placing the small vacuum nipple in the tee at 12 o clock to allow any moisture in the hose to drain back to the manifold, making it less apt to freeze in cold weather.) Step 3 - Under the hood- emove the rain tray Pull the rubber weatherstrip from the front of the plastic rain tray cover. Then pull the rain tray up slightly and straight forward to remove it.
6 Section 1 - un the Vacuum Line - Install the Transducer Step 4 - Under the hood- oute the plastic line Attach a short length of braided rubber hose to the vacuum tee nipple (tight fit, so push hard!). un the semi-rigid plastic vacuum line from the braided hose, across the front of the water tray to the rubber grommet located to the right of the battery. Push the line through the grommet. Then route the line back across the tray, in front of the battery, to the rubber firewall grommet located next to the brake booster. Use the zip ties in the kit to secure the plastic line at several locations. Leave a slight bend in the rubber braided hose at the vacuum tee to compensate for engine movement and vibration. Step 5 - Under the hood- Punch a hole in the firewall grommet Punch a small hole in the rubber grommet in the firewall (arrow), located between the brake vacuum booster and ECM. Page - 6
7 Section 1 - un the Vacuum Line - Install the Transducer Step 6 - Under the hood- Push line through grommet Push the plastic vacuum line through the small hole in the rubber grommet, into the cabin. Now it s time to move inside the cabin. Step 7 - Under the dash - emove fuse panel cover emove the underdash panel. Open the driver side door and pry off the fuse panel cover to expose the side dash panel attachment bolt (arrow). Use an 8mm socket and ratchet to remove the bolt. Step 8 - Under the dash - Drop underdash panel emove the two additional bolts from the underdash panel using the same 8mm socket and ratchet. Drop the panel down and unclip the purple data link connector and footwell lamp. No need to unplug them; just unclip both from the underdash panel and let them hang. Page - 7
8 ECS Tuning Vent Pod Vacuum/Boost Gauge Kit Section 1 - un the Vacuum Line - Install the Transducer Step 9 - Under the dash - Pull plastic line into cabin each up under the dash and pull the plastic vacuum line through the firewall grommet. oute the line toward the center console. Step 10 - Under the dash - Connect the transducer Inside the car, beneath the dash, use short lengths of the braided rubber vacuum hose to connect the plastic line to the moisture filter. Then use another short length of braided hose to connect the moisture filter to the transducer. Locate the lines and transducer near the center console, and secure them with zip ties. battery computer box boost sensing transducer wire harness to boost gauge moisture filter Page - 8
9 Section 2 - Install and Connect Vacuum/Boost Gauge It s time to install the vacuum boost gauge and make our electrical connections. The schematic below shows all component locations inside the car, and identifies the wire connections. brown light switch Vent Pod Vacuum Boost Gauge Wiring Connections and Component Locations Audi B6 A4 gauge power harness transducer harness black red gray/blue use alternate wiring for cars with auto headlight switch - see photos below black transducer red green white gauge power harness standard headlight switch electrical connector Special Note for Cars equipped with Auto Headlight Switch If your car has an Auto Headlight Switch, there is no keyed hot terminal (black wire) at the headlight harness connector. You ll need to pick up keyed voltage at the fuse box. To do so, install the fuse tap in your kit on the 15 amp fuse indicated in our photo. Attach the fuse tap to the fuse as shown and reinsert the fuse. Connect the red wire from the gauge harness to the fuse tap using the insulated terminal in the kit. Page - 9
10 Section 2 - Install and Connect Vacuum/Boost Gauge Step 1 - emove the dash vents Using a non-marring trim removal tool, pry the center vent assembly from the dash. Work your way around the perimeter to compress the spring clips as you pull the vent straight out. Step 2 - emove the vertical vents Pull the vent from the dash; flip it over and unplug the electrical connector. Step 3 - emove the Vent Cover Use a small common screwdriver to pry the tabs on the vent cover. Pry them loose one at a time until the cover pops off. Page - 10
11 Section 2 - Install and Connect Vacuum/Boost Gauge Step 4 - emove the louvers Pull the horizontal and vertical vent louvers from the left hand vent housing. Step 5 - Cut a notch in the vent flap Turn the assembly over. Use your X-ACTO knife to cut a square notch in the air control vent flap in the area highlighted in the photo. Step 6 - Drill a hole in the vent body Flip the vent housing over; drill a ½-inch hole in the location shown. Page - 11
12 Section 2 - Install and Connect Vacuum/Boost Gauge Step 7 - Pull the cables to the vent opening in the dash oute the gauge power cable and the transducer cable up through the left underdash area to the vent opening in the dash. Step 8 - Plug in the gauge Hold the vent housing up close to the vent opening and feed the two cables through the ½-inch hole drilled earlier. Pull both cables through the vent housing opening (arrows). Step 9 - Install the vent pod Hold the vent pod up to the opening. Feed the two cables through the round gauge hole, and let them hang. Page - 12
13 Section 2 - Install and Connect Vacuum/Boost Gauge Step 10 - Install the vent pod Insert one side of the vent pod into the vent hole. Align the small pins with the slots in the housing. Pivot the vent inward as you align the pins on with the slots in the opposite side opening. Step 11 - Install the vent pod With pins and slots aligned, press the vent inward until it snaps in place. Step 12 - Plug in the vent pod Lift up the vent housing and plug in the electrical connector removed back in step 2 of this section. Page - 13
14 Section 2 - Install and Connect Vacuum/Boost Gauge Step 13 - Plug in the vent pod Position the front trim bezel over the vent assembly, and press it inward until it snaps in place. Then press the complete assembly into the dash opening until it snaps in place. Step 14 - Connect the gauge Slide the o-ring in the kit over the gauge body, as shown. Plug in both electrical connectors. Step 15 - Install the gauge Align the gauge with the hole in the vent pod. Push in until the o-ring is no longer visible, and the gauge sits flat. This is a tight fit. You may want to apply a small amount of light lubrication to the o-ring to make it slide in more easily. Page - 14
15 Section 2 - Install and Connect Vacuum/Boost Gauge Step 16 - un the power wire Lower the steering wheel. oute the power wire from the over the top of the steering column toward the headlight switch. Step 17 - emove the light switch To remove the light switch from the dash, start with the light switch in the OFF position. Then push inward on the center knob and rotate it to the right until it stops. Pull straight out to remove the switch from the dash. Step 18 - emove the light switch Push the release tabs on the side of the housing and pull the electrical connector from the back of the switch. Page - 15
16 Section 2 - Install and Connect Vacuum/Boost Gauge Step 19 - Push the connector below the dash Push the electrical connector back through the headlight switch hole, and pull it out beneath the dash where you have more room to work. Using the directions on page 9, splice in all four wires from the gauge power harness to the correct wires at the headlight switch harness (or use the fuse tap for the red wire). oute the harness connector back through the switch hole in the dash. econnect the headlight switch and let it hang. Step 20 - einstall the light switch When wiring is complete, test gauge function and illumination. Key-on, the gauge dial should sweep to both extremes before settling back at zero. Step 21 - einstall the light switch With gauge operation verified, slide the light switch straight into the dash opening until it clicks in place. Page - 16
17 Finishing up Time to finish up: When you are sure the gauge is working properly, replace the underdash panel and fuse panel dash cover. Thanks! Thank you for purchasing the ECS Tuning Vent Pod Vacuum/Boost Gauge. We appreciate your business, and hope this installation guide has been helpful. Page - 17
for Audi B7/A4 ( ) Part Number ES8017 Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number for (2005-2008) Proper service and repair procedures are vital
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593109) for VW
More informationInstallation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW
More informationMKVI Jetta Fog Light Kit
MKVI Jetta Fog Light Kit Part Number VW Jetta Fog Light Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationvacuum/boost vent mounted ES best viewed in Acrobat Reader This tutorial is provided as a courtesy by ECS Tuning.
vent mounted vacuum/boost ES2713030 This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of
More informationInstallation. Instructions ES416. VW MKIV Golf/Jetta/GLI 337/20AE. to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems
Installation Instructions to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems This tutorial is provided as a courtesy by ECS Tuning. VW MKIV Golf/Jetta/GLI 337/20AE best viewed
More informationMKVI Jetta Fog Light Kit
MKVI Jetta Fog Light Kit Part Number VW Jetta Fog Light Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationAudi B6/B7 A4/S4/RS4 Refrigerated Glove Box Kit. Part Number ES This tutorial is provided as a courtesy by ECS Tuning.
Part Number Audi B6/B7 A4/S4/S4 efrigerated Glove Box Kit This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures Part Number for VW Passat B6 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures Part Number for VW MKVI Jetta GLI (model year 2012+) This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are
More informationZiza Interior Lighting Package Installation ES for BMW F10-5 Series (2011+)
Installation Procedures Ziza Interior Lighting Package Installation for BMW F10-5 Series (2011+) This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to
More informationInstallation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)
Page 1 This tutorial is provided as a courtesy by ECS Tuning. Service Procedure Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for BMW E90 Proper service and repair procedures are vital to the safe, reliable
More informationInstallation Instructions
Installation Instructions Table of Contents 2 - What Kit Do You Need? 3 - Old and New Blocks 4 - Installing the Bleeder Block 5 - Bleeding the System 6 - eaching the Block on MKIV 8 - eaching the Block
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for BMW E70 X5 (2007+) Proper service and repair procedures are vital to the safe,
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B5 A4 (sedan or Avant) (1996-2001) Audi B5 S4 (2000-2002) Proper service
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B7 A4/S4/S4 (2005-2009) Proper service and repair procedures are vital
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures Part Number for New Beetle Convertible This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for MKI TT (1998-2007) Proper service and repair procedures are vital to the safe,
More informationZiza Interior Lighting Package Installation Procedures
Ziza Interior Lighting Package Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Number for Audi B6 A4 (2002-2004) Audi B6 S4 (2004-2005) Proper service and repair procedures
More informationRS5mesh style Grille. Audi A5/S5. Installation Instructions. pre-facelift ES best viewed in Acrobat Reader
Audi A5/S5 pre-facelift RS5mesh style Grille Installation Instructions ES2627648 This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures
More informationES Installation Instructions. best viewed in Acrobat Reader. This tutorial is provided as a courtesy by ECS Tuning.
Installation Instructions This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures are vital to the safe, reliable operation of all engine
More informationUnder-Seat Storage Tray
Part Number ES6923 for VW MKV Golf/GTI and MKV Jetta/GLI/JSW Under-Seat Storage Tray This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures
More informationInstallation Procedures
Installation Procedures Ziza Interior Lighting Package Installation for BMW E46 Sedan This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe,
More informationMINI VIDI Integrated Digital Vent Gauge
R Installation Tutorial ES2718716 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as
More informationPorsche 996 Turbo Fuel Filter Replacement. Do-It-Yourself. This tutorial is provided as a courtesy by ECS Tuning.
Do-It-Yourself 2001-2005 Porsche 996 Turbo Fuel Filter eplacement This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of
More informationES6065 VW Golf/Jetta MKV and MKVI 2.0T Noise Pipe Bypass Duct Installation. Installation Procedures. Part Numbers: ES
Page 1 Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. Part Numbers: ES250690 ES6065 VW Golf/Jetta MKV and MKVI 2.0T Noise Pipe Bypass Duct Installation Proper service and
More informationInstallation Procedures
Installation Procedures Ziza Interior Lighting Package Installation for BMW E38 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationZiza Interior Lighting Package Installation Procedures
R Ziza Interior Lighting Package Installation Procedures Part Number for VW MKVI Jetta Sedan (S, SE, and SEL Trim) This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures
More informationInstallation Procedures
Installation Procedures This tutorial is provided as a courtesy by ECS Tuning. VW MKVI Jetta Seat Tray Installation Proper service and repair procedures are vital to the safe, reliable operation of all
More informationECS R32 Exhaust Flap Manual Override Installation Instructions
Installation Procedures This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of
More informationMKV Jetta OEM Fog Installation Instructions
Installation Procedures MKV Jetta OEM Fog This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the
More informationZiza Interior Lighting Package Installation ES
Installation Procedures for BMW E90 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as
More informationZiza Interior Lighting Package Installation ES
Installation Procedures for Audi B6 A4/S4 Sedan LED Interior Light Kit This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationZiza Interior Lighting Package Installation ES
Installation Procedures Ziza Interior Lighting Package Installation for BMW E70 X5 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationZiza Interior Lighting Package Installation ES
Installation Procedures Ziza Interior Lighting Package Installation for BMW E92 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable
More informationAudi A3 2.0 T FSI Fuel Pump
Installation Procedures Audi A3 2.0 T FSI Fuel Pump Cam Follower Replacement Kit ES2609354 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe,
More informationAudi A3 8P RS4-Style Grille
Audi A3 8P RS4-Style Grille Installation Tutorial ES2717887 ES2717886 1 However you choose to lift the car into the air, always ensure the car is secured properly and that the parking brake is engaged.
More informationInstallation Procedures
Installation Procedures Part Number for Audi B6 A4/S4 Audi B7 A4/S4 Audi C5 A6 Audi C6 A6 Heavy Duty Snub Mount Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair
More information2010+ VW Mk6 2.0T Vent Boost Gauge Kit INSTALLATION GUIDE
INSTALLATION GUIDE 2010+ VW Mk6 2.0T Vent Boost Gauge Kit Congratulations on your purchase of the AWE Tuning Vent Boost Gauge Kit for the 2010+ VW Mk6 2.0T. Exquisite build quality with industry leading
More informationForge 004 Dual Sprung Blow Off Valve Installation Instructions
Installation Procedures Forge 004 Dual Sprung Blow Off Valve This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationRS4 Style Grille. Installation. Audi B8 A4/S4 ES ES This tutorial is provided as a courtesy by ECS Tuning.
RS4 Style Grille Audi 2013+ B8 A4/S4 Installation ES2627562 ES2627563 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationAudi A4 1.8T Ultimate Timing Belt Kit Installation ES#8146
This is a supplement to the Audi 1.8T Ultimate Timing Belt Installation tutorial. Information in this document assists you in removing the front bumper/fascia and radiator support to gain access to the
More informationVolkswagen MKVI 2.0T ECS Tuning Kohlefaser Luft-Technik System. Installation Tutorial ES ES
Volkswagen MKVI 2.0T ECS Tuning Kohlefaser Luft-Technik System Installation Tutorial ES2712727 ES2739920 Required Tools: Flex Driver For Screw Type Hose Clamps* Phillips Screwdriver Torx T25 bit Torx T30
More informationVolkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions
Volkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationAudi B9 A4 & S4 Carbon Fiber Steering Wheel Trim Installation Instructions
Audi B9 A4 & S4 Carbon Fiber Steering Wheel Trim Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationMercedes-Benz S203 Interior Lighting Kit Installation Guide
Mercedes-Benz S203 Interior Lighting Kit Installation Guide ES2731764 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation
More informationAudi C6 A6 RS-style Grille Installation Tutorial
Audi C6 A6 RS-style Grille Installation Tutorial Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing
More informationBremmen Automatic Headlight Conversion Kit Installation Instructions
Bremmen Automatic Headlight Conversion Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationfor Audi B6 A4/S4 Installation Procedures Front Wheel Bearing Replacement This tutorial is provided as a courtesy by ECS Tuning.
Installation Procedures Front Wheel Bearing eplacement for This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FUEL SURGE TANK INSTALL KIT Honda S2000 Document# 19-0063 Support: info@radiumauto.com WARNING: DO NOT SMOKE WHILE WORKING ON FUEL SYSTEMS. KEEP SPARKS AND OPEN FLAMES AWAY FROM
More informationAudi B8 A4/5, S4/5 and RS5 Coilover Installation Instructions
Audi B8 A4/5, S4/5 and RS5 Coilover Installation Instructions This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all
More informationZiza Audi A3 8V Sedan Interior lighting Kit. Installation Tutorial ES
Ziza Audi A3 8V Sedan Interior lighting Kit Installation Tutorial ES2739194 General Tips When prying down on the assemblies to remove them, pry on the notched end of the lens. Insert the narrow tool tip
More informationECS Tuning 3095 Cleveland-Massillon Rd. Norton, Ohio Phone Fax Web
B7 A4 Gauge Pod Installation Instructions Safety first:. When working with your vehicles electrical system; always disconnect the battery! Avoid shorting any circuits, or probing around wires. Failure
More informationAudi Mk1 TT Vent Boost Gauge Kit
2000-05 Audi Mk1 TT Vent Boost Gauge Kit Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi TT. While the install is fairly straight forward, please review these
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More informationAudi B6/B7 A4/S4 Rear Wheel Bearing Service Kit
Audi B6/B7 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More informationAudi Q5/SQ5 Ziza LED Interior Lighting Kit Installation Instructions
Audi Q5/SQ5 Ziza LED Interior Lighting Kit Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationAudi A Timing Belt. Installation
Audi A3 2.0T Timing Belt Installation ES2538517 Audi A3 2.0 Timing Belt Installation This tutorial is provided as a courtesy by ECS Tuning. best viewed in Acrobat Reader Proper service and repair procedures
More informationRecommended tools: Estimated install time: Parts list:
Congratulations on your purchase of the A.W.E. Tuning Center Vent Boost Gauge for your Audi A4/S4. While the install is fairly straight forward, please review these instructions carefully before attempting
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationAudi B5 A4/S4 Rear Wheel Bearing Service Kit
Audi B5 A4/S4 Installation Tutorial ES2561175 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More information1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION
by Randy Irwin 1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 30 years. He is a wizard at creating,
More informationVolkswagen MKV/VI R32/Golf/Golf R Hatch Pop Kit
Volkswagen MKV/VI R32/Golf/Golf R Hatch Pop Kit Installation Tutorial MKV R32/Golf ES#1895197 MKVI Golf/Golf R ES#2083320 This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair
More informationVolkswagen MKIV 1.8T/2.0L/VR6 XAS Cold Air Intake System Installation
Volkswagen MKIV 1.8T/2.0L/VR6 XAS Cold Air Intake System Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationAudi B5 A4/S4 B6 A4 APR Performance Chip Tune ECU Removal and Installation
Audi B5 A4/S4 B6 A4 APR Performance Chip Tune ECU Removal and Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
More informationDODGE RAM 24V 5.9L CUMMINS
DODGE RAM 24V 5.9L CUMMINS DODGE RAM 24V 5.9L CUMMINS TABLE OF CONTENTS SECTION 1 Preparing the Installation 1 SECTION 2 Boost Gauge Installation 2 SECTION Pyrometer/EGT Gauge Installation 4 SECTION 4
More informationInstallation of Auto Meter Cobalt Boost/Vacuum Gauge:
Installation of Auto Meter Cobalt Boost/Vacuum Gauge: Fitment: All 79-14 models. This installation was completed on a 2004 Mustang GT, and should be identical for all 1999-2004 model Mustangs. Time needed:
More information1. Disconnect the battery. This is important! This will prevent air bag deployment.
PARTS PACKING LIST Evaporator assembly Drain tube Plastic air plug Hardware package 11040 3601 W. Clarendon Phoenix, Arizona 85019 (602) 233-0090 800-648-4475 www.ackits.com 2003-4 Jeep Wrangler EVAPORATOR
More informationAudi B7 A4 2.oT Lightweight Flywheel. Installation Tutorial ES
Audi B7 A4 2.oT Lightweight Flywheel Installation Tutorial ES2739501 Project Preparation Safety Leave the car in neutral. Park the vehicle in a safe, well lit, level area. Open the hood and place protective
More informationVW MK7 Golf/GTI/R/SportWagen S2T Aluminum Paddle Shifter Set Installation Instructions
VW MK7 Golf/GTI/R/SportWagen S2T Aluminum Paddle Shifter Set Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the
More informationSALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT
= SALEEN SPEEDLAB BOOST AND WATER TEMPERATURE GAUGE POD KIT INSTALLATION MANUAL: 2005-09 Mustang 4.6L 3V P/N: 10-8002-C12000B KIT P/N: 10-2903-B11511* Saleen Performance, Inc. 1225 East Maple Rd. Troy,
More informationSTREET SH ELD. Skill Level 1 - Easy. Audi B8 Tunnel Street Shield Installation Instructions - ES Basic Skills Required
Audi B8 Tunnel Street Shield Installation Instructions - ES3610307 Skill Level 1 - Easy Basic Skills Required STREET SH ELD Proper service and repair procedures are vital to the safe, reliable operation
More informationPHASE 3 POWERSPORTS AUDIO KIT RZR POLARIS. pg 2 Disassembly, Wire and Amplifier Plate Installation. pg 9 Glovebox Subwoofer Installation
POLARIS RZR PHASE 3 POWERSPORTS AUDIO KIT pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25 MRB3 and Dash Kit Installation
More informationBMW N54 Kohlefaser Luft-Technik Twin Cone Intake Installation
BMW N54 Kohlefaser Luft-Technik Twin Cone Intake Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those
More information#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
More informationNissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
More informationRZ3-5K Polaris RZR XP 1000 & 900 Kicker 5 Speaker Audio Kit
PO H PWER PO 5 O KIT I E D U A S A TS S I R LA R Z R R O SP pg 2 pg 9 pg 13 pg 25 pg 29 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationRZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit
RZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationpg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation
RZ3-5KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers
More informationVolkswagen MKVI GTI Carbon Fiber Front Diffuser Installation Instructions
Volkswagen MKVI GTI Carbon Fiber Front Diffuser Installation Instructions Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationDetroit Speed, Inc. Selecta-Speed Wiper Kit Corvette P/N:
Detroit Speed, Inc. Selecta-Speed Wiper Kit 1968-72 Corvette P/N: 121621 A downpour of rain will no longer hinder your ability to clearly see the road. The Detroit Speed Selecta-Speed Wiper Kit provides
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationThank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit Before You Start Please read instructions completely before installing. These instructions contain the information required to install
More informationITEM QTY CHECK PART NUMBER DESCRIPTION
PART #90542A Boost Gauge Package, SLP, 2005-2013 Corvette PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationTrail Rocker Installation Instructions
Trail Rocker Installation Instructions Manual #90580 For Installing Painless Part Numbers: 57000 and 57001 Painless Performance Products recommends you, the installer, read this installation manual from
More informationRZ3-3A Polaris RZR XP 1000 & 900 SSV Works 3 Speaker Audio Kit
RZ3-3A Polaris RZR XP 1000 & 900 SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationTrack Rocker Installation Instructions
Track Rocker Installation Instructions Customizable Track Rocker Control System For Installing Painless Part Number: 58100 Track Rocker Relay Center Manual #90641 Painless Performance Products recommends
More informationDetroit Speed, Inc. Electric Headlight Door Kit Corvette P/N: &
Detroit Speed, Inc. Electric Headlight Door Kit 1968-82 Corvette P/N: 122006 & 122007 The Detroit Speed Inc. Electric Headlight Door Kit replaces the stock vacuum actuated system on all 1968-82 Corvettes.
More informationITEM QTY CHECK PART NUMBER DESCRIPTION. NOTE: This package does not include any accessories for gauge installation
PART #90540A Gauge Pod Only Package, SLP, 2005-2013 Corvette PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationGMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control
U 17 December 2014 (1036606) 2006-07 GMC Duramax (LBZ) High Idle Kit (I-00318) 1 GMC Duramax (LBZ) High Idle Kit Note: Only for automatic transmissions with cruise control 1036606 2006-2007 GMC Duramax
More information2.0 FSI Quick Spool Crank Pulley Installation Instructions
Installation Procedures 2.0 FSI Quick Spool Crank Pulley This tutorial is provided as a courtesy by. Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles
More information