INTAKE SWAP INSTRUCTION MANUAL 1.Items to pick up before you begin:
|
|
- Ferdinand Morris
- 5 years ago
- Views:
Transcription
1 INTAKE SWAP INSTRUCTION MANUAL 1.Items to pick up before you begin: Someone to lend you a hand for about 10 minutes Intake gasket set that pertains to your year of engine Coil of your choice Spark plugs (Copper Accel U-groove is our preferred choice) Wires (5.8 wires also an option sometimes fit nicer and tighter) 5/16 fitting (Brass: barbed on one side / male threads on the other) A pack of JB Kwik weld (We prefer Kwik due to its set up time) Block off plate for mechanical fuel pump 5/16 Hard fuel line (20 spool) Flaring kit for fuel lines (if you don t already have one) 5/16 EFI rubber line (about 4 ) EFI Style hose clamps (Size 14-16) Fuel Filter (We prefer the Wix clear plastic ones over the expensive Mr. Gasket glass ones) Two fuse holders (you ll need a 15-amp and a 10-amp fuse also) DVOM (voltmeter) if you don t already own one 195 Thermostat Thermostat Gasket (AutoZone has a nice reusable one) Heat shrink but connectors, get a couple of each size. Harbor Freight s are the cheapest and the best) A package of different sized vacuum caps (we prefer Nylon colored ones, we have found they stand up better than rubber)
2 When your kit arrives please remove everything from boxes and confirm that nothing is damaged from shipping and handling. Use an air compressor and blow out all passages of the intake and throttle body!! 1. Disconnect Battery. 2.Tear Down 2. Rotate engine to TDC position. 3. Before removing the Distributor: One of our tricks for later dropping the new distributor in is to take a picture of the cap s orientation and then the rotor s orientation. 4. Remove the distributor and use a rag to plug hole to prevent contaminants from falling into the engine. 5. Drain Coolant (Don t drain oil yet, Coolant will fall into oil passages when pulling intake) 6. Remove ignition box located by driver side firewall (unplug, don t cut). Leave the wires that go to the Starter, Alternator, Air Conditioning, oil pressure and coolant sensor. Remove all remaining ignition wires from the engine.
3 7. Removing intake: a. Disconnect throttle cable or linkage. b. Disconnect fuel lines running to carburetor (These can be cut since new lines will need to be ran). c. Remove intake (Coolant will drain into oil system). 8. Remove Mechanical Fuel Pump and install a fuel pump block off plate. 9. Through the fuel pump passage: you must inspect timing chain (VERY IMPORTANT!! If not in spec, replace timing chain now). a. Pictured below is an out of spec timing chain that was very close to jumping teeth and engine destruction. 10. See pedal and cable modification instruction manual for style that applies to your kit and vehicle. This is easiest if done with the intake removed. 3.Intake Installation
4 1. Before you begin, do a final clean and inspections of intake to ensure it is clear of debris (we recommend blowing out with compressed air). On the engine use a razor blade to scrape all the mating surfaces, then use acetone to remove grease and residue. 2. Install intake with new gaskets and torque to spec a. This can be done full assembled (but is usually much easier if the fuel rails, injectors, and throttle body are removed). b. Using clean bearing grease: lightly coat all O-rings, threads, and barbed ends. c. Reinstall injectors, fuel rails, and throttle body. 3. Install fittings into fuel rails a. Install adapters on ends of fuel rails. The O-ring side goes on the rails x4 i. Part# EAR-AT985006ERL
5 b. Install both the -6AN to 3/8 90 barbed ends on rear of fuel rails pointed towards driver side hand tight i. Part# SUM B c. Install both -6AN to 3/8 150 barbed ends on front of fuel rails pointed towards center and down hand tight i. Part# SUM B d. Refer to orientation in picture below i. Front
6 ii. Rear e. Use 3/8 EFI hose to connect the front adapters together as seen in pictures (Be sure it will clear the distributer when installed). f. Use 3/8 EFI hose to connect the passenger side rear to the fuel pressure regulator. It can be mounted anywhere where convenient if needed. g. High Pressure or Feed line will be on the driver side rear with the barbed end. h. Low Pressure or Return line will come off the Regulator to return to tank s fill up tube. i. After this is all set-up and the orientation is good, tighten all the AN fittings and hose clamps. 4. Running Fuel Pump and High Pressure Feed Lines a. Mount the fuel pump as low on the frame and as close to the fuel tank as possible. i. Run a wire from where the old ignition box was down to the (+) prong of the fuel pump (We will hook this up later). ii. Clean a good spot on frame for the ground wire of the fuel pump.
7 b. You can use your existing steel fuel lines after the fuel pump up to the 3/8 barbed fitting on the fuel rail. However, any and all rubber fuel lines must be replaced with EFI rated fuel line and only use EFI style hose clamps. c. Always install the fuel filters BEFORE the pump. i. If you have dual tanks refer to the dual tank instruction manual. d. We HIGHLY recommend that you use your bubble flare tool for all the hardline connections. 5. Running the Low Pressure Return line Do Not run the return line into the burp tube, it will making pumping gas next to impossible. a. For dual tanks refer to the dual tank instruction manual b. Before you begin, use a Sharpie and mark a good place to install the return line. You will want this about an inch up from where the Fill Tube s rubber stops. Then remove fill-up tube. Clean with water to ensure no gas vapors left in tube. c. Drill a pilot hole about where you have the Sharpie mark. Then drill the hole larger so that turning the brass barbed piece in is very difficult but possible. d. Clean the fill up tube out of any debris. e. Using your 5-16 brass fitting thread into hole carefully.
8 i. This is where you will use the JB KWIK weld to ensure that the fuel will not leak. 4.Perform Oil Change and Replace Coolant 1. There will be coolant in oil from removing old intake. The old oil helps flush all possible coolant out of the oil pan. Go ahead and do your oil change now. 2. Fill up your coolant system. 5.Distributor Installation 1. Clean distributor hole of debris (a clean shop rag works fine). 2. Install distributor in same orientation in which it was pulled off (refer to the pictures you took earlier). 3. Tighten down the hold down snug where you can still make adjustments later. 4. Don t install spark plug wires yet (they will just get in the way).
9 6.Installing Wiring Harness 1. PLEASE READ THIS SECTION SEVERAL TIMES, then begin. a. DO NOT hook up battery (+) (-) until instructed. These components are tough but are easily damaged by intermittent power, ground, or faulty tachometer. WE ARE NOT LIABLE FOR FRIED components due to improper power or ground. b. NEVER leave keys in ignition while connecting or disconnecting battery. c. NEVER use a tachometer that is not 100% confirmed reliable and functional. d. It Is HIGHLY recommended that you install a sufficient ground from engine to chassis and from engine to battery (Insufficient ground can lead to grounding through ECU and overloading it). e. When installing pigtails do not attempt to force them this can bend prongs and then your system will not perform as it should or at all (Some connectors are keyed differently but look very similar). 2. Installing wiring harness a. Start by placing the ECU on the driver side fender under the hood spring with the connector side facing the firewall b. Connecting the 60-pin connector to the ecu: i. Hand thread the 10mm bolt that holds in until hand tight (be gentle this should feed in nice and smooth). ii. Using a 10mm socket gently and slowly secure the connector (notice when it is seated and STOP!).
10 c. Fuses and relays will run towards the driver headlight and mount on the fender just after ECU, as pictured below. d. On the harness, the longest lead will be thin with two wires coming out. These are BATT (+) and BATT (-). i. Run these wires along the top of the firewall around to the passenger side. ii. DO NOT HOOK UP YET! (this is just for harness placement). e. If harness came in two separate parts, connect them now (Engine side and Chassis side). f. Start with the leg that is labeled with Injector #1 Injector#4 i. This side will be fed around the backside of the intake with Injector #1 coming closes to the front passenger side of engine. ii. Connect INJECTOR #1 INJECTOR #4 g. Hook up distributor pigtail towards the front of the engine. h. Connect Coolant Temp Sensor and Air Charge Temp i. Coolant Temp Sensor is located next to Injector #5 ii. Air Charge Temp is located at the center of the intake just in front of the throttle body. iii. WARNING! At a glance, these connectors look the same but are keyed in different ways.
11 i. Connect INJECTOR #5 INJECTOR #8 located on driver side of engine j. Connect Throttle Position Sensor located on the throttle body. k. Connect Idle Air Bypass. i. It is located at the back of throttle body. l. Connect Coil. i. We have marked + - for ease to use whatever application you prefer (Use supplied pink weatherproof butt connectors). m. Connect and mount MAP sensor i. Find a good place that both the connector and vacuum tube can be connected without stressing wires or rubber tube. n. Connect spark plug wires. i. Firing order 460/429 + FE motors ( ) ii. Firing order 400m/351m ( ) o. Oxygen Sensor i. We recommend placing O² Sensor from the closest exhaust port on the driver side. With long tube headers place it at the collector. You will need to weld in the provided Sensor Bung. ii. The Oxygen Sensor lead has a 4-wire set that is unloomed in the middle. This to offer ease of installation for the customer, this part of the harness can be shortened or lengthened depending on application iii. Use the supplied heat shrink but connectors, tape over each individually with electrical tape and use the provided cold shrink tape to protect harness.
12 p. Ignition Module installation i. If ignition module is attached to distributor, attach this now if you haven t already. ii. If ignition module is separate, this MUST be mounted to a metal surface because it is grounded through its mount (We recommend using 2 self-tapping screws, and clean around these screw holes to bare metal). iii. There should now only be 5 wires left not hooked up iv. Wait to hook these five wires up until later 1. ACC (+) KEY POWER ON 2. BATT (+) 3. BATT (-) 4. TACHOMETER 5. And the fuel pump wire that was ran earlier v. Besides these five wires make sure all the other pigtails are plugged into their sensors and that all fuel fittings are tight. q. With the harness still completely unplugged from any power or ground, hook up the battery. 6. Time to find where to hook up the last five wires 1. Grab your helper and your DVOM (voltmeter) a. If your installation is in an old Ford: Locate the old ignition module plug that looks like the female side of an old-style household extension cord (Pictured
13 below). Go ahead and cut the two wires and wire strip off ¼. i. Locate the wire that shows 0 volts but has full power when the key is on and also while cranking the engine. 1. Have your helper jump in and make sure the vehicle is in park or neutral and wheels chocked. 2. While you are reading the power at that wire, have them turn the key to on (note the voltage). Then have them crank the engine to ensure it still has at least 10+V while the engine is cranking. 3. If you have found the correct wire disconnect the battery positive and negative. Leave disconnected until the end of this section. 4. Install supplied Y-shaped connector (pictured below). Cap the other wire that you cut. 5. The 1 st butt connector is where you will hook up the ACC (+) / Key Power On wire that is red with a black stripe. In the 2 nd install a
14 fuse holder and hook your fuel pump (+) wire to it. Install a 10-amp fuse. ii. If your vehicle doesn t have a wire in the engine bay that supplies the correct power, you will need to find one coming from the ignition switch. b. TACHOMETER i. If running an aftermarket tachometer that is 100% confirmed good hook this wire up to the tachometer wire coming from the harness (it is green with a black stripe). ii. If your install is in a vehicle with a factory tachometer, you will need to find out if it takes the same signal as an aftermarket tachometer. c. BATT (+) i. Install the second fuse holder (install 15amp fuse) to either the positive terminal or the hot side of the solenoid. Then connect the yellow battery (+) wire up to the fuse holder. d. BATT (-) i. THIS MUST BE GROUNDED TO THE BATTERY 1. Cannot be grounded to frame or body 2. Now that all the wires are securely ran go ahead and hook up the battery. Prime fuel pump and check for leaks a. Key the vehicle on ensure that the fuel pump is turning on (Wait and let it prime up the fuel system). b. Do this cycle a few times to make sure no fuel is leaking anywhere and to make sure the fuel rails are primed for initial start-up 3. Initial Start-Up
15 a. Pull out the TIMING PLUG located right next to the ignition module b. Start engine c. Use timing light to set distributer to 10 BTDC d. Return plug to TIMING PLUG 4. Before your drive a. The ECU needs to learn and adapt to your specific engine (which it will fully do over the first couple days). b. Before you drive, let the engine run to full operating temp. c. Remove the Timing Plug again and set the timing between BTDC this time (10 BTDC was factory spec, but we all run ours at with no problems or issues). d. Before you drive the vehicle give the engine a few short wide-open throttle taps. Also, go through the RPM ranges a bit. 5. Test Driving a. In the first few miles drive conservatively (the ECU is still learning the engine). b. Short bursts of wide open throttle are ok. c. Try to avoid any long duration wide-open throttles or extended under-load scenarios. At for the first 100 miles (don t go pulling a trailer or driving up a mountain). We love to get pictures and reviews to put up on our website. It lets people know all the benefits of our
16 EFI kits. It makes us proud to see them on the road, doing tractor pulls, in the water, running snow cats, launching airplanes, and running equipment. So please send us some pictures and talk about your experience with our kits. From all of us here a 460 EFI Guys we hope you enjoy your EFI system
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED
BMW 2002 M42 Swap Notes-THIS IS NOT FINISHED This document is to help those that want to install an m42 into a BMW 2002. It is based around an e30 engine, trans, and wiring. You can use the e36 block/head/wiring
DrVanos.com Stage II Installation Instructions. Tool rental is available with the purchase of a vanos kit *See website for more info*
DrVanos.com Stage II Installation Instructions Special Tools Needed: Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
FULL LENGTH HEADERS/ CATTED HEAD PIPES
INSTALLATION INSTRUCTIONS INS232 2016-2018 CAMARO 6.2L V8 FULL LENGTH HEADERS/ CATTED HEAD PIPES Part #4044 and 40440 Special Tools required: 10mm, 12mm, 13mm, 15mm Socket and Wrenches, Pliers, Saw, Welder
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc.
Thank you for purchasing the Dezod Motorsports Return Fuel System for your Scion tc. We took much pride in putting together a fuel system that would deliver a maximum amount of fuel as simply as possible
PIMP Ford 5.0 Harness Installation Manual. Part Number: PM-75
PIMP Ford 5.0 Harness Installation Manual Part Number: PM-75 Ron Francis Wiring 200 Keystone Rd Suite 1 Chester, PA 19013 800-292-1940 www.ronfrancis.com Pre-Installation Notes: This system is designed
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+)
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit For R56, R58, R59, R60 with Refresh Engines (2011+) Before You Start Please read instructions completely before installing. These
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours
Ford Racing Performance Improvement Intake Manifold (96-04 GT) Time Necessary: Approximately 4 hours Tools Required: Ratchet and socket set Torque wrench Large adjustable wrench Needle nose pliers A dozen
C40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
PRXB EXHAUST BRAKE MAXIMUM EXHAUST FLOW DESIGN
MAXIMUM EXHAUST FLOW DESIGN PRXB EXHAUST BRAKE C44072/C44073/C44074/C44075/C44076 APPLICATION: 994-2002 DODGE RAM TRUCKS W/5.9L CUMMINS DIESEL ENGINES WITH MANUAL & AUTOMATIC TRANSMISSIONS STOCK DODGE
Special Tools Needed: DrVanos.com Stage I Installation Instructions Camshaft locking tool TDC Crank pin Sprocket turning tool Tool rental is available with the purchase of a vanos kit *See website for
Ford Racing 4.6L 3V Crate Engine Control Pack
Ford Racing 4.6L 3V Crate Engine Control Pack Installation Time: 3-6 hours on a Foxbody Mustang Tools Required: Basic English and Metric Socket and Wrench Set Flat and Phillips Screwdrivers Torx bits Hammer
72 Mustang Mach 1 tachometer cluster and gauge conversion
72 Mustang Mach 1 tachometer cluster and gauge conversion Dated: 02-17-2009 (drafted by a Chevy person working on his first Ford -not good-) Revised: 11-05-2010 The following information pertains to how
C WD 2 WHEEL LOW KIT FOR DODGE RAM 4WD VEHICLES
C18056-4WD 2 WHEEL LOW KIT FOR 1994-2002 DODGE RAM 4WD VEHICLES Pacbrake s 4WD 2 Wheel Low Kit allows the vehicle operator to engage the transfer case into 4WD low range without engaging the front wheel
M-Tuned reroute kit XX
M-Tuned reroute kit 14-161XX Manufactured and designed by: *Professional Installation Recommended but not required 1) Disconnect the negative terminal from the battery in the trunk. 2) Drain the coolant
X-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
HOWELL INSTALLATION MANUAL. Throttle Body Fuel Injection Harness
HOWELL ENGINE DEVELOPMENTS, INC. FUEL INJECTION APPLICATIONS INSTALLATION MANUAL Throttle Body Fuel Injection Harness Howell Engine Developments, Inc. 6201 Industrial Way Marine City, MI 48039 Phone: 810-765-5100
Remove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
Part Number: TDZ-75SD / BRONCO-75SD
Ford 5.0 EFI Harness Installation Manual For Classic Fords & Mustangs and Early Broncos Part Number: TDZ-75SD / BRONCO-75SD Ron Francis Wiring & The Detail Zone 200 Keystone Rd. Chester, PA 19013 800-292-1940
84-86 Ford SVO Mustang AC Installation Guide
84-86 Ford SVO Mustang AC Installation Guide This installation guide is for the AC installation kit from Late Model Restoration. The Vendor is Hose Wizards that manufactures this great kit that provides
Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
WARNINGs! Read all instructions before starting installation of this product! Installing the improper FASS Pump can cause severe engine damage.
WARNINGs! Read all instructions before starting installation of this product! Installing the improper FASS Pump can cause severe engine damage. FASS Recommended Application T F17 150G Powerstroke (6.7L)
AMS F1-I INTAKE MANIFOLD
AMS F1-I INTAKE MANIFOLD The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will never compromise
Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 6.7L
04/05/2012 Dodge 2010-2011 6.7L Twin CP3 701-900-2356-INST Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2010-2011 Dodge 6.7L Figure 1 - Full Kit Photo 29 Figure 2 - Hardware Kit (800) 949-60002
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod
Connecting the rear fog light on the A4 Jetta, while keeping the 5 Light Mod DISCLAIMER: I'm human and make mistakes. If you spot one in this how to, tell me and I'll fix it This was done on my 99.5 Jetta.
SLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
MSD 7AL-3, Ignition Control PN 7230
MSD 7AL-3, Ignition Control PN 7230 Important: Read the instructions before attempting the installation. Parts Included: 1-7AL-3, PN 7230 1 - Parts bag (wires and connectors) 4 - RPM Modules 3000, 7000,
C FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
Slingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
BBK Intake Manifold Kit ( L) - Installation Instructions
BBK Intake Manifold Kit (86-93 5.0L) - Installation Instructions The below installation instructions work for the following products: BBK Intake Manifold Kit (86-93 5.0L) Please read through the instructions
Property of American Airlines
Gen. II Ford 300 Install 1775 N. Lapeer Rd. Unit B Oxford, MI 48371 248-393-1621 TABLE OF CONTENTS 1. Kit Contents....3 2. Installation Instructions.. 4 3. Component Description.....10 4. Final Checks....12
TROUBLESHOOTING FOR EFI ELECTRONIC CIRCUIT WITH VOLT/OHMMETER
FI118 TROUBLESHOOTING FOR EFI ELECTRONIC CIRCUIT WITH VOLT/OHMMETER HINT: Because the following troubleshooting procedures are designed for inspection of each separate system, the actual troubleshooting
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS
CHALLENGER TWIN TURBO SYSTEM INSTALLATION INSTRUCTIONS 1 Verify contents of kits with supplied packing list 1) Unhook the battery. 2) Remove wheel wells & front fascia of vehicle. 3) Remove the catalytic
Step 6: Remove and save the MAP sensor for later use. Step 7: Remove the passenger side intercooler pipe and the EGR intake manifold.
LBZ Twin kit Install Step 1: Disconnect both batteries. Step 2: Drain coolant and oil also remove passenger side inner fender. Step 3: Remove intake box and piping. (Remove and save the MAF sensor in the
#TL T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS
#TL100069 2.0T EA888 GEN 3 FUELING SYSTEM/ INSTALLATION INSTRUCTIONS Notes: These instructions were written for a North American specification MkVII GTI. Other models, like the Golf R, are similar. When
Turner M50 Manifold Adapter Install. April 26, 2012
April 26, 2012 Models: 1996-99 E36 328i/M3; 1997-98 E39 528i, 1997-98 Z3 2.8, 1998-2000 MZ3 S52 Product(s): Turner M50 Manifold Adapter Kit Subject: Installation Guidelines and Tips This guide will aid
H - TESTS W/O CODES INTRODUCTION SYMPTOMS
H - TESTS W/O CODES 1995 Volvo 850 1995 ENGINE PERFORMANCE Volvo - Trouble Shooting - No Codes 850 INTRODUCTION Before diagnosing symptoms or intermittent faults, perform steps in the F - BASIC TESTING
Electromotive Tec GT Installation Supplement for the Porsche
Electromotive Tec GT Installation Supplement for the Porsche 928 1987-95 Copyright 2009 928 Motorsports, LLC. all rights reserved Toll-Free Tech Hot Line: 877-FOR-928M 877-367-9286 Please do not copy this
Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
YOU WILL BLOW YOUR MOTOR UP IF YOU MOUNT A SUPERCHARGER TO THIS KIT AND DRIVE AWAY WITHOUT INTEGRATING A RELIABLE TUNING METHOD!!!!!!
NOTICE This supercharger mounting kit is sold with NO supercharger head unit and is intended for use with Vortech supercharger head units exclusively. DO NOT attempt to adapt any other manufacturer s supercharger
PRXB EXHAUST BRAKE HIGH PERFORMANCE
HIGH PERFORMANCE PRXB EXHAUST BRAKE C44059, C4406, C44063, C44065 APPLICATION 994-2002 DODGE RAM AUTOMATIC TRUCKS EQUIPPED WITH 47RE TRANSMISSIONS WITH 5.9L, 24 VALVE CUMMINS DIESEL ENGINES GETTING STARTED
IAG Air / Oil Separator (AOS) For STi
IAG Air / Oil Separator (AOS) For 2008-14 STi Part# IAG-ENG-7000 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors Sockets: 10mm, 12mm 13mm Wrenches: 10mm,
2015+ HELLCAT 6.2L HEMI System vehicle specific plate system xx
These installation instructions will guide you through installing the Nitrous Outlet 2015+ Hellcat 6.2L Hemi Vehicle Specific Plate System on your vehicle. Before you get started, remember to never use
Retro it Steering Column
Retro it Steering Column INSTALLATION INSTRUCTIONS for 1976-86 CJ5 & CJ7 FOR PART NUMBER S: 1520800010, 1520800020, 1520800051, 1526800010, 1526800020, 1526800051 S I NCE 1986 Instruction # 8000000010
APIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS
APIKOL AAN INTAKE MANIFOLD INSTALLATION INSTRUCTIONS Estimated Installation Time: Approximately 2 hours Parts that will need to be modified/removed (Details provided later in the instructions): Intercooler
INSTALLATION INSTRUCTIONS
1. Note: It is recommended this install be done with a minimal amount of fuel in the tank. This will reduce fuel spills and make installation easier and safer. Draining the tank is recommended. INSTALLATION
Installation Manual v2.2: Twin CP3 Fuel Injection Kit Dodge 5.9L
12/13/11 ATS Twin CP3 Kit 701-900-2272-INST Installation Manual v2.2: Twin CP3 Fuel Injection Kit 2003-2004 Dodge 5.9L Figure 1 - Full Kit Photo 26 Figure 2 - Hardware Kit 1 Please read all instructions
Revised 10/23/2015 Page 2 of 10
1.Remove the gauge, side panels, hood and headlight. Remove the air box from the throttle bodies then remove the seat and gas tank. 2.Carefully remove temp sensor from air box using a small pick or screw
HOWELL INSTALLATION MANUAL. Tuned Port Or LT-1 Fuel Injection Harness ( )
HOWELL ENGINE DEVELOPMENTS, INC. FUEL INJECTION APPLICATIONS INSTALLATION MANUAL Tuned Port Or LT-1 Fuel Injection Harness (1985-1992) Howell Engine Developments, Inc. 6201 Industrial Way Marine City,
Installation Manual v1.0: Twin CP3 Fuel Injection Kit Dodge 5.9L
Installation Manual v1.0: Twin CP3 Fuel Injection Kit 2004.5-2007 Dodge 5.9L Figure 1 - Full Kit Photo 25 Figure 2 - Hardware Kit Please read all instructions before installation. This kit is not emissions
INSTALLATION AND USER MANUAL
INSTALLATION AND USER MANUAL SDKIT-730 & SDKIT-734 100% Bolt-On 150 PSI Train Horn System for 2011-2015 F-250 & F-350 Super Duty P/N SDKIT-730 P/N SDKIT-734 Thank you for purchasing a Kleinn Air Horns
Shotgun Single Barrel HPFP install guide
Shotgun Single Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Single Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
How to stick a 3.4L engine into your Boxster.
How to stick a 3.4L engine into your Boxster. When I purchased my 99 Boxster in January, it was already equipped with a TPC supercharger setup. While fun and a great improvement over the rather anemic
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part# 69-0717 AIR IT UP 4 Tire On Board Installed Air Delivery System with Rear Mounted Controller (Requires External Air Source) For the most up-to-date instructions please visit
Rostra Electronic Cruise Control Install On a Stratoliner or Roadliner
Rostra Electronic Cruise Control Install On a Stratoliner or Roadliner MATERIALS LIST: 1 - Rostra Part # 250-1223 (www.brandondist.com/products/cruise1223.htm) 1 - Signal Splitter part # 250-4369 1 - Engagement
Water Temperature. GM LS Engine Gauges Installation Guide
2650-1563-00 GM LS Engine Gauges Installation Guide Water Temperature For water temperature, there is a port located on the right side (passenger side) of the engine, in the cylinder head, past the last
L Intake Manifold Part #
86-93 5.0L Intake Manifold Part #5001-5002 I N S T A L L A T I O N I N S T R U C T I O N S Supplied Materials Bottom cover, Upper manifold, Lower manifold, Plenum cover plate, 1501 Throttle body (comes
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit
2017+ L5P Duramax 3 ½ Down Pipe & EGR Fix Kit Covers installation of PN s: WCF100630, WCF100829 Note: This Kit is for off road competition use only! Off Road Competition Use Tuning & Exhaust System is
ESS INSTALL. The donor car /6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9
ESS INSTALL The donor car.. 1997 540/6 Cosmos Black/Sand UUC Short Shifter Brembo cross drilled rotors Phillips Nav System 16:9 The install went in several stages. Disconnect the battery Stage 1 Remove
(905)
(905)953-9260 Marc@M-Tuned.com Coolant Reroute Kit *Professional Installation Recommended but not required 1) Disconnect Negative Terminal from Battery in trunk. 2) Drain Coolant from your cooling system.
FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How
1 of 29 10/12/2011 5:05 PM FREE $15 Gift Card for every $100 spent on Ship To Home orders. Find Out How Ford Ranger/Explorer/Mountaineer 1991-1999 Intake Manifold REMOVAL & INSTALLATION Print The engines
Install a starter Relay to cure the Le Sharo s non starting condition
Install a starter Relay to cure the Le Sharo s non starting condition Inspired by Moljinar from VW Vortex Forum Adapted by Jacques Pagé from Yahoo LESHARO OWNERS Group Most starters use an electromagnetic
Fuel Delivery Requirements
held Controller the Go EFI System creates a base fuel MAP to get the engine running. Then the self tuning programming will fine tune the MAP to produce optimum power and performance. Through the use of
On all settings above 100 horsepower the following precautions should be observed:
ELECTRONIC FUEL INJECTED 5.0 COYOTE PLATE SYSTEM INSTALLATION INSTRUCTIONS Congratulations on the purchase of your Nitrous Express Coyote Plate system. Nitrous Express utilizes only the highest quality
WARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
M-TUNED COOLANT RE-ROUTE KIT
M-TUNED COOLANT RE-ROUTE KIT Part # MC-RR-216, MC-RR-218 Applications: 90-93 Miata 1.6L B6 94-97 Miata 1.8L BP More detailed instructions: http://www.etdracing.com/m-tuned/reroute.pdf 1) Disconnect Negative
Procharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
Shotgun Double Barrel HPFP install guide
Shotgun Double Barrel HPFP install guide Thank you for your purchase of the VTT Shotgun Double Barrel HPFP upgrade! First thing to do when you open your box is to make sure all parts are in their respective
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit
Thank you for purchasing the Craven Speed FlexPod Complete Gauge Pod Kit Before You Start Please read instructions completely before installing. These instructions contain the information required to install
Installation Instructions
2011-2013 LML DURAMAX COMPOUND-ADD 2011-2015 LML A Duramax TURBO KIT Add INSTALL A Turbo INSTRUCTIONS Compound Kit Installation Instructions 1-800-955-0476 - www.industrialinjection.com - info@industrialinjection.com
KIT CONTENTS. Multimeter or test light Wire crimpers or soldering equipment. Wire terminals & connectors 10A inline fuse
RUSSELL FORD 5.0L COMPLETE EFI PLUMBING KIT INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new complete fuel system kit. If you have any questions, please call
ADM Performance 6079 Mapleshade Lane Dallas, Texas (214)
1) Disconnect Battery Ground 2) Raise front end of Vehicle FAN INSTALL INSTRUCTIONS 3) Remove lower Radiator hose and drain coolant into a pan. (you will reuse coolant later) 4) Remove Air Intake piping
Installation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
FI AirGap intake installation instructions
Updated March 2016 FI AirGap intake installation instructions Please read and understand all of the instructions and check to make sure that all of the parts (shown on last page) are present before you
Accel 300+ Ignition Control System (84-95) - Installation Instructions
Accel 300+ Ignition Control System (84-95) - Installation Instructions The below installation instructions work for the following products: Accel 300+ Ignition Control System (84-95) Please read through
Weistec M156/M159 ENGINE
Weistec M156/M159 ENGINE Oil / Air Separator System Installation Guide 2007-2011 S63 AMG 2007-2011 ML63 AMG 2007 R63 AMG 2007-2008 CLK63 AMG 2008 CLK63 Black Series 2007-2011 CLS63 AMG 2008-Present C63
LML 3 Y-Bridge Kit or High Flow Intake Bundle Package
2011-2016 LML 3 Y-Bridge Kit or High Flow Intake Bundle Package Covers installation of PN s: WCF100607, WCF100691, WCF100716, & WCF100353 Note: This Kit is for off road competition use only! Overview-
9415 W. Ridge Rd. Elsie, MI
9415 W. Ridge Rd. Elsie, MI 48831 248-393-1621 989-862-4163 TBI INSTALLATION INSTRUCTIONS Congratulations on the purchase of your Affordable Fuel Injection TBI system. We are confident that this purchase
INSTRUCTIONS. EZ-EFI FK In-Tank Fuel Kit
1 INSTRUCTIONS EZ-EFI 30401-FK In-Tank Fuel Kit Thank you for choosing FAST products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,
Installing Ignition Coil relay
Installing Ignition Coil relay Above is a schematic diagram of the coil relay modification. All it really does is, it uses the existing 12 Volt positive that normally powers the coils, to power a relay,
Small knife. Remove black panel shown. Save 6 retaining pins for re-install later.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver PB-3425 Parts Bag 1 Ratchet & Socket set OR Ford OEM Switch (if you 1 Adjustable
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #
2006 Honda Civic SI Supercharger Kit Installation Instruction Kit #350-091 3239 MONIER CIRCLE, STE.5 RANCHO CORDOVA, CA 95742 916.635.4550 FAX 916.635.4632 www.ct-engineering.com INS-157 VERSION: 3.25.2009
CLASSIC UPDATE WIRING KIT
by Randy Irwin 1955-57 CLASSIC UPDATE WIRING KIT Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 25 years. He is a wizard at creating, making and modifying custom
Nissan GTR Alpha Fuel System
Nissan GTR Alpha Fuel System Instructions V5 The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs
WEBER CARBURETOR TROUBLESHOOTING GUIDE
This guide is to help pinpoint problems by diagnosing engine symptoms associated with specific vehicle operating conditions. The chart will guide you step by step to help correct these problems. For successful
Always wear safety glasses when working on your vehicle.
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
H - TESTS W/O CODES Nissan 240SX INTRODUCTION TROUBLE SHOOTING SYMPTOMS DIAGNOSIS WILL NOT START
H - TESTS W/O CODES 1990 Nissan 240SX 1990 ENGINE PERFORMANCE Trouble Shooting - No Codes Nissan; 240SX, Axxess, Maxima, Pathfinder, Pickup, Pulsar, Sentra, Van, INTRODUCTION Before diagnosing symptoms
SDS Continental O-200 Installation Manual Aug. 4/17
SDS Continental O-200 Installation Manual Aug. 4/17 This manual covers the steps to install the SDS EM-5 fuel injection and ignition system components on O-200 engines. Hall Sensor and Bracket Install
05-08 GT. Hellion Power Systems Mustang Kit Instructions
Hellion Power Systems 05-08 Mustang Kit Instructions 1. Disconnect Battery 2. Drain Radiator, keep fluid for re-installation. 3. Remove air box and inlethoses. 6. Next, underneath, punch oil pan for turbo
DirectMount EXHAUST BRAKES
DirectMount EXHAUST BRAKES APPLICATION: Fixed Orifice and PRXB Exhaust Brakes 2003 2005 Dodge Trucks with 3.5" & 4" Exhaust and 47RE & 48RE Automatic Transmissions Only Vehicles with an existing air compressor
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Part# 22-7810 Add On Kit for Your ADS System Contents: Complete Install Kit for Your ARB CKMTA12V Compressor For the most up-to-date instructions please visit www.updownair.com
SAISBM V36W Installation Instructions
The Original Secondary Air Injection System Bypass Kit SAISBM V36W Installation Instructions All Applicable Toyota/Lexus Vehicles Introduction: The Secondary Air Injection System (SAIS) bypass module is
Installation Manual for the Pantera Ignition Switch Bypass
Installation Manual for the Pantera Ignition Switch Bypass This Ignition Switch Bypass solves the Pantera owners problem of replacing the ignition switch that is expensive and difficult to source. The
INSTRUCTION MANUAL CHEVROLET APPLICATIONS
INSTRUCTION MANUAL FOR CHEVROLET APPLICATIONS (including LT-1) www.accel-ignition.com Installation Manual For The ACCEL Digital Fuel Injection Engine Management System Prior to starting the installation
ARC4000e 4 wheel compressor system w / 4 way Ride Pro controller
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 on the internet: www.ridetech.com ARC4000e 4 wheel compressor system w / 4 way Ride Pro controller 1 ARC5001 Compressor 1 CON6000
QUICKSTART MANUAL SNIPER EFI INSTALLATION INSTRUCTIONS
550-510, 550-511, & 550-516 QUICKSTART MANUAL SNIPER EFI INSTALLATION INSTRUCTIONS Congratulations on your purchase of a new Sniper EFI Throttle Body System built by craftsmen to exacting standards in
TOP FEED FUEL RAIL KIT for WRX
TOP FEED FUEL RAIL KIT for 2002-14 WRX Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
Retrofit Steering Column
Retrofit Steering Column INSTALLATION INSTRUCTIONS for 1970-75 Camaro FOR PART NUMBER S: 1620860010, 1620860020, 1620860051, 1626860010, 1626860020, 1626860051 S INCE 1986 www.ididitinc.com 610 S. Maumee
INSTALL MANUAL D o d g e 1 2 v 6 B T A PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
PN#1045310 12V Dodge Twin Turbo Kit (I-00273) 1 INSTALL MANUAL BD Twin Turbo Kit 1994-1 9 9 8 D o d g e 1 2 v 6 B T A Part# 1045310 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION. * Picture as shown
TELORVEK TPI WIRING INSTRUCTIONS FOR TH-90 (95 CK TRUCK) 4.3,5.0,5.7,7.4 TBI Fuel Injection System W/4L60-E or 4L80-E Transmission
Page #1 TELORVEK TPI WIRING INSTRUCTIONS FOR TH-90 (95 CK TRUCK) 4.3,5.0,5.7,7.4 TBI Fuel Injection System W/4L60-E or 4L80-E Transmission Thank you for purchasing the absolute finest of wiring kits for