Self-propelled hovercraft
|
|
- Priscilla King
- 5 years ago
- Views:
Transcription
1 Self-propelled hovercraft Materials: Styrofoam Meat Tray [0S].5v DC Motor Plastic Propeller (3-Blade, 3.5 dia) or similar AAA Cell Battery Holder (For Batteries) [] AAA Batteries [] 8 Lead Wires (Red/Black) [] 8.5 x Cardstock Sheet s: Double-Sided Tape, White Glue, Masking Tape Utility/X-Acto Knife Build time: Hour Model adapted from Fifteen Minute, Self-Propelled Hovercraft, posted by Dr. No, July 30, 006, on
2 Step : Make the Intake The science: As the propeller displaces the air that it s moving through, the intake redirects that air below the tray, creating the air cushion that makes the craft hover. The intake also supports the motor. 3 We ve attached a pattern for the intake see following page. Print the pattern onto 8.5 x cardstock. Using an X-Acto knife (or similar), cut out the intake: Cut along all solid gray lines and the four magenta lines. Fold along all blue dotted lines. Place a strip of adhesive double-stick tape on the tabs, and attach the tabs to the underside of the intake s back panel. Make sure to line up the tabs blue dotted lines with the edge of the back panel. Once everything is lined up correctly, the back panel will incline down at 45 degrees, and the side panels will be at 90-degree angles to the top of the intake.
3 INTAKE CUT-OUT Cut Along Solid Gray Lines Cut Through Magenta Lines Fold Along Blue Dotted Lines To fit standard 0S styrofoam meat tray DECK CUT-OUT Back Edge of Intake Back Edge of Intake CUT OUT AND REMOVE THIS AREA A A Front
4 Step : Make the Deck 3 4 We ve attached a pattern for the deck see preceding page. Using an utility/x-acto knife, cut out the deck. Cut out and remove the light gray square in the center of the deck. Using double-sided tape, attach the deck to the bottom of the styrofoam tray. Using a utility/x-acto knife, cut out and remove the styrofoam square below the opening in the deck.
5 Step 3: Attach the Intake! Apply double-sided tape/white glue to the deck inside all areas labeled either or A. Carefully align the /-inch intake flaps with the corresponding markings on the deck pattern and apply. The two triangle folds in front of the intake must be parallel to the opening as shown below.
6 Step 4: Motor/Prop Assembly 3 Attach the propeller to the motor shaft (wrap it in tape if it s too narrow). You may also fill the hole in the propeller with hot glue, allow the hot glue to cure, and drill a new hole that matches the diameter of the shaft. Center the motor and propeller on top of the intake. The propeller should be as close to the intake s opening (without touching the opening) as possible. Secure the motor across the intake with masking or other tape.
7 Step 5: Wire the Batteries! Wire the battery holder to the motor. Attach the positive lead (+) to the (+) side of the motor. Similarly, wire the negative lead (-) to the (-) side. DC Motors spin in either direction, depending on how the leads are connected. If you plan to solder the connections, first make sure that, when the propeller turns, air is flowing into the intake. Attach the battery holder to the deck with masking or other tape. Do this lightly. The performance of the hovercraft depends on having even weight distribution. You may want to relocate your battery holder to balance the craft after testing.
8 Step 6: Test The science: Hovercrafts are also known as Air Cushion Vehicles (ACVs). ACVs work because of lift. Attaining lift begins by forcing air into the intake and under the hovercraft where it is trapped by a skirt. When enough air is trapped under the craft, the pressure forces the vehicle off the ground. Once the hovercraft is off the ground, a small amount of air escapes continuously from beneath the skirt, and the vehicle floats on this cushion of air.!! TestinG: Turn on the batteries and...you re off! If the hovercraft seems to drag along one edge, try repositioning your battery pack to balance the weight of the vehicle. If the hovercraft turns dramatically, try repositioning the motor by turning it slightly away from the turn.
9 Hovercraft Airflow Map Air pulled through the propeller and INTO the intake a escapes under the hovercraft, creating a cushion of air. The hovercraft floats on this cushion of air. Air pulled through the propeller and PAST the intake moves the hovercraft forward.
Bugatronics Kit Directions
Bugatronics Kit Directions The Bugatronics kit comes with everything you need to make a picture that teaches circuitry. The circuit pattern suggestion included in the kit is a parallel circuit but you
More informationDIY Bi-Metallic Strip
DIY Bi-Metallic Strip An introduction to the applications of thermal expansion and two-way switching. Written By: Mahaaveer BN 2018 Page 1 of 14 INTRODUCTION A bi-metallic strip is used to convert a temperature
More informationWARNING: CHOCKING HAZARD
Hover Racer WARNING: CHOCKING HAZARD - Small parts. Not for Children under 3 years. To Parents: Please read all instructions before giving guidance to your children. A. SAFETY MESSAGES 1. This kit is intended
More informationCircuit 1: Closed Circuit A closed circuit is a complete circuit that allows current to flow.
Paper Circuits Gather the following materials: Paper Circuit video tutorials 4 pieces of copper conductive tape (each will be cut into 18 pieces) 5 LEDs (3mm) 1 coin cell battery (3V) 1 binder clip (optional)
More informationFifteen Minute, Self-propelled Hovercraft
instructables Fifteen Minute, Self-propelled Hovercraft by Dr. No This instructable coves how to build a hovercraft out of a foam tray, cardboard, and some other household items. Step 1: Materials For
More informationThese instructions show how to build the Remote Controlled Fart machine Sound Kit.
Remote Controlled Fart Machine Assembly Instructions These instructions show how to build the Remote Controlled Fart machine Sound Kit. Tools Required Drill with 7/64, 3/16, and ¼ drill bits. Holt melt
More informationIn area - A -, a proper seal must be made against the top of the window glass.
Door window, adjusting Page 1 of 3 Audi > B3 > 1994-1998 Body Exterior, Interior 61 - Convertible top, checking and adjusting Door window, adjusting Sections C-C and D-D. Adjust door window so that window
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (DECK LID) ACCORD 4-DOOR AII 24063 Issue Date AUG 2002 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) ACCORD 4-DOOR AII 30276 Issue Date AUG 2005 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring (marked
More information1464. Interior Installation. Cover Rear Seat Support Cut the vinyl to approximately the size of the rear seat support.
Chapter 37 (Video Clip 37) - Interior Installation 1464. Interior Installation Cover Rear Seat Support 1465. Cut the vinyl to approximately the size of the rear seat support. 1466. Make a dry fit of the
More informationApplication Note. Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes
Application Note Atlas RS-3 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 digital sound decoder into an HO Atlas RS-3. Skill Level
More informationPAPER CRAFT. Assembly Instructions
PAPER CRAFT Assembly Instructions Thank you for downloading the "SR400"paper craft model. By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble
More informationBuilding a Wind Speed Indicator (anemometer) to use with the Sparkfun weather:bit module
Building a Wind Speed Indicator (anemometer) to use with the Sparkfun weather:bit module You can build your own wind speed indicator from items typically found around the house. Then you can connect it
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. UNDER 2007 CIVIC SI All 33529 Issue Date AUG 2006 PARTS LIST Rear under spoiler Clip Rubber washer 6 Flange bolts 6 Flange nuts TOOLS REQUIRED
More informationJames Aircraft. INDUCTION SYSTEM, CARBURETED Please read all instructions prior to starting
INDUCTION SYSTEM, CARBURETED Please read all instructions prior to starting Carbuetor / Injecter Kit Includes: Filter housing, saddle base, back plate, hinge section and transit duct. ADDITIONAL MATERIALS
More informationStep #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good t
How to make a ROV! Step #1 From your spool of 18 gauge primary wire, cut between 11 and 21 three inch strips of wire. You will only need 11 for the ROV, but it is good to have extras. Using the wire cutter,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25877 PILOT Issue Date AUG 2003 Optional ATF and power steering coolers are required when installing the trailer hitch. 2 Spacers PARTS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CASSETTE PLAYER 2000 ACCORD (EX) 2- AND 4-DOOR All 20497 Issue Date JULY 1999 PARTS LIST Cassette Player Attachment Kit Except V6: P/N 08B12-S84-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory BACKUP S Application 2014 CR-V Publications No. AII 49959 Issue Date JULY 2013 PARTS LIST Right corner sensor clip (Black) Backup Sensor Attachment Kit P/N 08V67-T0A-100
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27955 SIDE 2005 CIVIC SI Issue Date AUG 2004 PARTS LIST Left side under spoiler Right side under spoiler 6 Plates 8 Clips Template INSTALLATION
More informationBuild your own THUNDERBIRD 2
PACK 01 STAGE PAGE 01 Nose assembly and Elevator Car rear wheels 3 02 Cockpit interior and Elevator Car 1 completion 7 03 Missile launcher and Thunderbird 4 11 04 Nose assembly and the Tracy brothers 15
More informationBruce s Science workbench
Baby Vandegraff Generator by Bruce Yeany 2001 https://www.youtube.com/watch?v=parq01q DKe4 http://www.instructables.com/id/van-de- Graaff-Electrostatic-High-Voltage- Generator/ https://www.youtube.com/watch?v=esz
More informationRe-Energy.ca - Solar Electricity - Build Your Own Solar Car
Backgrounder Build Your Own Solar Car Back to Page 1 Build It! These step-by-step instructions provide you with a plan for making a basic solar car. If you can think of ways to improve the design of your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 30518 KIT 2006 PILOT Issue Date NOV 2005 NOTE: Accessory ATF and power steering coolers are required when installing the trailer hitch.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 24081 ACCORD 2-DOOR Issue Date SEP 2002 PARTS LIST INSTALLATION NOTE: Rear under spoiler Be careful not to damage the rear bumper and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationMustang Shaker
2005-2009 Mustang Shaker CDC #110050 ( 05/ 06) or 0711-7000-01 ( 07/ 09) Component Check List: Quantity/Description Part # CDC Installer 1 - Engine Cover Assembly 114050 1 - Aluminum Shaker Scoop 183020
More informationFlyzone Spitfire FF to R/C Conversion Instructions
Flyzone Spitfire FF to R/C Conversion Instructions Hobbico Flyzone EP FF airplanes have been around for years, with exciting new models being added constantly. The recent interest shown by R/C modelers
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 40454 XM SATELLITE RADIO 2009 S2000 Issue Date AUG 2008 PARTS LIST Template XM Radio Unit Kit (sold separately): P/N 08A53-S2A-101 XM
More informationREV READ BEFORE INSTALLATION OF KIT:
REV. 05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691509 A7EDG-7820049-AAPLN EDGE BODY KIT- V6 B PCS & EXH TIPS 1 691256 A 7 E D G - 7 8 20049-BAPLN EDGE BODY KIT- V6 8PCS & EXH TIPS W/HITCH 1 691501
More informationInstruction Manual. Specification:
Instruction Manual L O W Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1790gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo W I N G KIT CONTENTS: We have
More informationTillotson Tc3A Carburator
Tillotson Tc3A Carburator 176 FUEL SYSTEMS - 5B-11 CENTER BOWL TYPE CARBURETOR Removal 1. Remove front cowl cover and wrap-around cowl. 2. Remove swivel link from lower carburetor. (Figure 2) 3. Loosen
More informationSHELF STAXX ACCESSORY INSTALLATION INSTRUCTIONS
The Narrow Depth Long Component Tray (Depth 3) is compatible with 100-grid Staxx kits. The Component Tray kits include mounting brackets, screws and nuts. One section of the component tray will have a
More informationPhysical Sciences (Energy and Matter) Objective: To determine what household items are good conductors of electricity. The purpose of this
Objective: To determine what household items are good conductors of electricity. The purpose of this investigation is to demonstrate an understanding of simple closed circuits as well as evaluate the electrical
More informationApplication Note. Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes
Application Note Bachmann F40PH Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 Digital Sound Decoder into a Bachmann HO F40PH. Skill
More informationHP ENTERPRISE 600 M651/M680 SERIES TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
HP ENTERPRISE 600 M651/M680 SERIES TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS HP 652A TONER CARTRIDGE RREMANUFACTURING THE HP COLOR ENTERPRISE 600 M651/M680 SERIES TONER CARTRIDGES By Mike Josiah and
More information2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill 1-3/4" Hole saw 2" Hole saw
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Roll Bar (Mm5RB-20.1 to -20.6) Recommended Center punch 1/8" pilot drill
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 33322-36889 UNDER 2007 TL Issue Date MAY 2007 PARTS LIST Front under spoiler Left bracket (Marked L ) Right bracket (Marked R ) 8 Self-tapping
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SPOILER (LOW) 2005 ACCORD 4-DOOR AII 27503 Issue Date AUG 2004 PARTS LIST Trunk spoiler Right trunk spring (marked green) Left trunk spring
More informationINSTALLATION INSTRUCTIONS
Accessory Application Publications No. INSTALLATION INSTRUCTIONS SIDE S 2013 TSX BII 13496 Issue Date SEP 2012 PARTS LIST 4 Screws Left side under spoiler Right side under spoiler 2 Clamps TOOLS AND SUPPLIES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory REAR SPOILER Application 2011 CR-Z MUGEN Publications No. AII 45919 Issue Date APRIL 2011 PARTS LIST Right wing bracket Rear wing Left wing bracket Right wing base Right
More informationINSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT
INSTALLATION AND OWNER S MANUAL Side Illumination Lights Z5150 for use with K 1200 LT Read these instructions carefully and thoroughly before beginning work. Before installing the accessory, carefully
More informationStep 1 : Starting the installation
Installation Instructions for GM Remote Start w/ INTSL Interface Pre-wired Review the remote start installation manual for safety instructions! Overview Your kit consists of two modules a remote start
More informationTable of Contents. Tail Wheel Assembly Installation.. page 01. Stabilizer Installation.. page 02. Fin Installation.. page 03
Table of Contents Tail Wheel Assembly Installation.. page 01 Stabilizer Installation.. page 02 Fin Installation.. page 03 Elevator and Rudder Hinge Installation.. page 04 Rudder Controls.. page 05 Elevator
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW AII 27366 ODYSSEY Issue Date P/N 08R12-SHJ-100 SEP 2004 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the left speaker
More informationInstallation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si
Page 1 Installation Manual TWM Performance Shift Boot 2006 and up Honda Civic Si Begin the installation by parking on a flat surface, as you may have to engage and disengage the hand brake and shift from
More informationKinetic Contraptions. Build a Hovercraft, Airboat, and More with a Hobby Motor. Curt Gabrielson
Kinetic Contraptions Build a Hovercraft, Airboat, and More with a Hobby Motor Curt Gabrielson Contents Acknowledgments ix Introduction 1 Getting Started 5 Safety 9 Basic Circuitry 11 Mounting the Motor
More informationCervini's Functional Ram Air Kit (05-09) - Installation Instructions
Cervini's Functional Ram Air Kit (05-09) - Installation Instructions The below installation instructions work for the following products: Cervini's Functional Ram Air Kit for 05-09 Ram Air Hood Cervini's
More informationALMOST READY TO FLY. Wing Span in cm. 2
ASSEMBLY MANUAL ALMOST READY TO FLY MS:X9 Specifications Wing Span --------------------------61.4 in ---------------------------156cm. 2 Wing Area --------------------------606.1 sq.in ------------------
More informationOnwards and Upwards, Your near space guide. Figure 1. We don t need wheels where we re going.
The robotic hovercraft is a nearly frictionless robotic platform. A robotic hovercraft, or HoverBot, travels almost without friction because it does away with one of the greatest sources of drag, spinning
More information1) PROBLEM STATEMENT :
TABLE OF CONTENT: 1) PROBLEM STATEMENT 2) HOVER THEORY 3) ELEMENTS OF A HOVERCRAFT 4) DESIGN CONSEDERATIONS 5) ELECTRONIC EQUIPMENT 6) HOVERCRAFT BUILD 7) TROUBLESHOOTING 1) PROBLEM STATEMENT : To design
More informationBuild Manual. Vector & Xtra Slick
Build Manual Vector & Xtra Slick Warning information this is not a toy! Read and understand entire manual before assembling model Do not overlook the warnings and instructions enclosed or those provide
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B. Display bracket.
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2006 PILOT All 30502 Issue Date SEP 2005 PARTS LIST Attachment Kit(sold separately): P/N 08B23-S9V-100B Display
More information1 Engine nacelle kit with outrigger for A 10 and similar models 7249 /52 1 Taper collet, 3.17 mm bore, 2 locking screws and cap nut 7249 /69
Instructions for Order no. 249/51 The impeller unit was developed by our team of experienced model flyers for semiscale electric-powered model jets. The result is that the is designed specifically to cater
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. THIRD-ROW P/N 08R12-SHJ-100 2008 ODYSSEY AII 38141 Issue Date OCT 2007 PARTS LIST Left rear sunshade Driver s Side 1. Remove the spare tire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25852 PILOT Issue Date AUG 2003 PARTS LIST INSTALLATION NOTE: Door visor (Front left) These instructions show the left door visors being
More informationI n s t r u c t i o n M a n u a l. Instruction Manual SPECIFICATION
I n s t r u c t i o n M a n u a l Instruction Manual SPECIFICATION - Wingspan: 3200mm (125,9 in) - Length: 1650mm (64,9 in) - Flying weight: 3000gr 3200gr - Wing area: 64.5 dm2 - Wing loading: 46g/dm2
More informationA S S E M B L Y G U I D E
MODEL SOLAR ELECTRIC POWER BOAT PLUGGING into the sun! SEND US YOUR COMMENTS A S S E M B L Y G U I D E Flexible solar cell turns sunlight into electricity resulting in a forwards force on the boat allowing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2004 S2000 AII 26323-31611 Issue Date DEC 2005 PARTS LIST Rear defroster switch Hardtop 3-Pin subharness (If equipped, not used) 4-Pin subharness
More information2005+ Drag Race Roll Bar (Mm5RB-20)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com 2005+ Drag Race Roll Bar (Mm5RB-20) Note that the NHRA DOES allow the door bars
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26031 2004 ODYSSEY Issue Date AUG 2003 NOTE: You cannot install the subwoofer in a vehicle equipped with both an under seat Navigation
More information2005+ Mustang Trunk Lid Release and Trunk Lights Installation
There is no warranty expressed or implied by this document, you follow these instructions at your own risk. These instructions worked for me, but your experience may vary. The final product of these instructions
More informationRoadComfort TM. Installation Manual Vibration Massage & Heat
RoadComfort TM Vibration Massage & Heat Installation Manual 1-562-447-1780 WWW.RELAXOR.COM Table of Contents I Required tools II System Configuration III Motor Placement Bottom IV Motor Placement Back
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HITCH Application 2012 CROSSTOUR Publications No. AII 46198 Issue Date JULY 2011 PARTS LIST Trailer Hitch Kit P/N 08L92-TP6-101 Upper spacer A (5 mm) (Some are not used.)
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII 42587 Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170
More informationJitterbug. Project description. Activity 1 Create a Design brief that would best fit this project description
Jitterbug Name Class Teacher Project description Simple DC motor spins a eccentric Cam with the weight offset to one side creating an up/down rapid vibrating movement. This vibration is then conveyed to
More informationAthearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD CF7 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD CF7. Skill Level 2: The entire
More informationRe-Stuffing the Multi-Capacitor Can in 600 Series Zenith Trans-Oceanics
Re-Stuffing the Multi-Capacitor Can in 600 Series Zenith Trans-Oceanics 2014 by Ed Morris 600 Series Zenith Trans-Oceanic radios have a four section multi-capacitor can located behind the dial face. When
More information2010 Mustang V6 Shaker CDC #
- - Incomplete 2010 Mustang V6 Shaker CDC # 1011-7002-01 Component Check List: Quantity/Description Part # Engine Cover Assembly 1011-6000-01 1 Engine Cover w/ Upper Air Tube 0511-2100-01 1 Aluminum Shaker
More informationBMW Z4 - By: Eigenes Bild (CC-BY-SA)
Instructions to transfer the hydro pump on a BMW Z4 (E85) to the trunk (AKA boot) and replace the hydraulic hinges and hydraulic hoses if necessary. Graciously provided by Chuck B in Illinois. BMW Z4 -
More informationAthearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes
Athearn RTR EMD GP35 Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-AT1000 into an Athearn HO Ready-To-Roll EMD GP35. Skill Level 2: The
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM (EXCEPT LX) 2006 ODYSSEY All 30392 Issue Date AUG 2005 PARTS LIST XM Radio Attachment (sold separately): P/N 08B15-SHJ-100
More informationIMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! TOOLS REQUIRED
IMPORTANT: PLEASE KEEP THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE! 2014-15 Toyota Tundra Mesh Grille Upper Insert - Fits ALL model Tundras with chrome or painted factory grille surround Black Mesh Part
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory DECK LID SPOILER Application 2014 RLX Publications No. BII 13399 Issue Date JAN 2013 PARTS LIST Trunk spoiler Left trunk spring (marked yellow) Right trunk spring (marked
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory SPOILER (LOW) P/N 08F10-TA0-100 Application 2009 ACCORD 4-DOOR Publications No. AII 40062 Issue Date JULY 2008 PARTS LIST Trunk spoiler Right trunk spring (marked red)
More informationGiving your Tiger a Cool Gulp of Fresh Air with Functional Ram Air
Giving your Tiger a Cool Gulp of Fresh Air with Functional Ram Air We have all heard that the LAT-79 option fiberglass hood was intended as a competition option to improve the performance of the Tiger
More informationTrainer Assembly Manual
Trainer Assembly Manual www.pilot-rc.com -Pilot Trainer- 1 -Pilot Trainer- 2 -Pilot Trainer- 3 -Preliminary i wing & stab assembly- 1-) Locate both Plywood wing joiners (Large and small one) 2-) Insert
More informationCHAPTER 15 FURNISHINGS. Section Title Page
CHAPTER 15 FURNISHINGS Section Title Page 15.000 Description..................................... 15.1 15.100 Seat Harnesses................................... 15.3 15.110 Four-Point Harness Assembly.................
More informationX-Type w/ non-premium sound amplifier installation instructions
X-Type w/ non-premium sound amplifier installation instructions 1. Pull radio from dash (see Radio Removal Instructions ) 2. Disconnect wiring harness from back of radio by pushing in tab on plug and pulling
More informationRevised 10/23/2015 Page 2 of 10
1.Remove the gauge, side panels, hood and headlight. Remove the air box from the throttle bodies then remove the seat and gas tank. 2.Carefully remove temp sensor from air box using a small pick or screw
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2011 CIVIC 4-DOOR Si Publications No. AII 44423 Issue Date AUG 2010 PARTS LIST Template Front under spoiler TOOLS AND SUPPLIES REQUIRED 4 Self-tapping screws
More informationKeeping You Cool Under Pressure
Installation Instruction for 92-93 GM 6.5L Turbo Diesel Series 3500-4 Wheel Drive Pickup and Series 1500, 2500, 3500 4 Wheel Drive Suburban Intercooler System (Part No. 2-436) TOOLS REQUIRED: 1.) Normal
More informationApplication Note. Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes
Application Note Athearn Genesis SD70MAC Tsunami Digital Sound Decoder Installation Notes Overview This application note describes how to install a TSU-GN1000 digital sound decoder into an Athearn Genesis
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 3RD ROW P/N 08R12-SHJ-100 2006 ODYSSEY AII 30563-31117 Issue Date OCT 2005 PARTS LIST Left side rear sunshade Driver s Side 1. Remove the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More informationPRELIMINARY INSTALLATION INSTRUCTIONS. PARTS LIST Left front trim piece
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece
More information1:6 BLACK BRANT II. c o s m o d r o m e r o c k e t r y
c o s m o d r o m e r o c k e t r y 1:6 BLACK BRANT II This kit is capable of use with high thrust motors. It is therefore strongly recommended that epoxy be used throughout the construction of this kit.
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. All 40290 BODY SIDE 2009 RIDGELINE Issue Date AUG 2008 PARTS LIST INSTALLATION NOTE: Be careful not to damage the body paint finish. Left
More informationFlyzone P-40 FF to R/C Conversion Instructions
Flyzone P-40 FF to R/C Conversion Instructions Hobbico Flyzone EP FF airplanes have been around for years, with exciting new models being added constantly. The recent interest shown by R/C modelers in
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REAR VIEW CAMERA ATTACHMENT PILOT AII 23620 Issue Date MAY 2002 PARTS LIST Attachment Kit : P/N 08B21-S9V-100 Control unit harness Rear
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. in- ENTERTAINMENT SYSTEM 2004 TSX BII 24811 Issue Date APRIL 2003 PARTS LIST Attachment Kit P/N 08B23-SDA-101A Monitor bracket harness FM
More informationDoor panel insert trim replacement Volvo V70
Door panel insert trim replacement 1998-2000 Volvo V70 Tools needed: Torx Driver T25, Putty Knife, Bone Tool (optional), Heat gun or Dremel cutting tool, wire brush (or use a plastic tile and grout brush),
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application CR-V Publications No. AII 12065 Issue Date DEC 2011 PARTS LIST Left front body side molding Right front body side molding TOOL AND SUPPLIES REQUIRED Masking
More informationSunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais
SunFlower Helicopter Rocket LUNAR Build Session: 9/25/08 By Tom Desmarais Contents of Kit: A. 3 1/16 x1 x11 basswood rotors B. 3 1/16 x2 x2 basswood fins C. 3 1/16 x5/16 x1/2 basswood hold spacer D. 3
More informationQTY 3D PN. FCS PART NUMBER DESCRIPTION
Rev.05-08 QTY 3D PN. FCS PART NUMBER DESCRIPTION 1 691224 A6ZEP-17B635-AAPLN MKZ FRONT AIR DAM 1 691202 A6ZEP-5410154-AAPLN MKZ SIDE SKIRT RH 1 691203 A6ZEP-5410155-AAPLN MKZ SIDE SKIRT LH 1 691225 A6ZEP-17E957-AAPLN
More information2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH
2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH The Watson Racing Battery Relocation Kit is NOT designed to protect you in the case of an accident, and therefore is INTENDED
More informationInstallation instructions, accessories - Rear Seat Entertainment
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 2004 10 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008 Replaces issue: 2003 12 J3904620 Page 1 of 18 Required tools A0000162 A0000163
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S 1998 CIVIC 2/3/4-DOOR All 18767 Issue Date SEP 1997 PARTS LIST Fog Light Kit: P/N 08V31-S01-100 Right fog light (marked R ) Fuse label
More informationRockyHydro. System Assembly Info Packet
RockyHydro System Assembly Info Packet RockyHydro sells a wide degree of micro-hydro components for various kits. Our customers enjoy the benefit of being able to carefully match a turbine and generator
More information4TH GEN SEATS IN A 3RD GEN TRUCK
4TH GEN SEATS IN A 3RD GEN TRUCK by Flopster843 02 Oct 2016 If you drive a 3rd generation Dodge Ram truck, I am sure you have discovered that the OEM seats are not the greatest (Figure 1.) They are extremely
More information