EFFECT OFSHIMMING ON THE ROTORDYNAMIC FORCE COEFFICIENTS OF A BUMP TYPE FOIL BEARING TRC-B&C
|
|
- Lindsay Ward
- 5 years ago
- Views:
Transcription
1 TRC Project 32513/1519F3 EFFECT OFSHIMMING ON THE ROTORDYNAMIC FORCE COEFFICIENTS OF A BUMP TYPE FOIL BEARING TRC-B&C A Shimmed Bump Foil Bearing: Measurements of Drag Torque, Lift Off Speed, and Identification of Stiffness and Damping Coefficients Luis San Andrés Principal Investigator Joshua Norsworthy Graduate Research Assistant May 2014
2 Introduction Gas Foil Bearings Bump-type foil bearings (BFB) : a gas film in series with a compliant under-spring is a choise support for microturbomachinery (<400kW) Typically top foil, shaft or both oated to minimize wear & reduce friction Issues: Expensive highly engineered elements Nonlinear substructure: contributes to sub synchronous rotor whirl motions Thermal management advised LOW load capacity (compared to oil lubricated bearings) 2
3 Justification & Past Work Issue: BFB supported rotors often show large sub synchronous whirl motions. Kim and San Andrés (2009) Trib. Trans., Vol. 52 Sim et al. (2012) J.Tribol. Vol.134 Oil free turbocharger on shimmed foil bearings Sim et al. (2014) Proc. ASME Turbo Expo 2014 Three pad BFB Prior art: shimmed BFB increases the onset speed of rotor instability and reduces the amplitude of sub synchronous whirl motions Shimmed (mechanically preloaded) BFBs are a low cost way to ensure stable performance.
4 Test BFB and shims Shims have one surface with adhesive. Shims press some bumps closer to the rotor L=38.1 mm, arc=12 o, Thickness =30 µm,50 µm Shims placed 120 apart, stretch axially through bearing FB radial clearance, c nom =(D I -D s )/2= mm Other BFB dimensions. Add slide Bearing dimensions L= 38.1mm D = 36.5 mm L/D~ 1.03
5 Clearance of shimmed BFB t 1 2cnom 2 s Clearance profile: c( ) 1 cnom ts cos NS 1 p c nom : Nominal bearing clearance t S : Shim thickness N S : Number of shims θ : Angular coordinate θ p : Angular distance between consecutive shims θ 1 : Angular coordinate of the first shim The clearance of a shimmed bearing is periodic resembling a tri-lobe or three pad bearing. The bearing clearance reduces at shim locations.
6 Rotordynamic test rig Bearing TC cross-sectional view Max. operating speed: 80 krpm Turbocharger driven rotor Regulated air supply: 7.58 bar (110 psig) Test journal diameter:36.5 mm Journal press fitted on shaft stub turbocharger, Model T25, donated by Honeywell Turbo Technologies
7 Drag Torque Top shaft speed = 60 krpm Speed up to 60 krpm, steady state operation, and deceleration to rest. Lift off speed occurs at the lowest torque denoting airborne operation
8 Start up drag torque (dry friction) Peak startup torque Torque max variability : ±5 N-mm Bearing with 30 µm shims Bearing with 50 µm shims Bearing lift off speed Max. variability : ±2.5 krpm Bearing with 50µm shims Original bearing Original bearing Bearing with 30 µm shims f T RW Drag torque and rotor lift off speed increase with specific load Friction factor of shimmed BFBs increases with shim thickness and decreases with specific load
9 Breakaway friction factor Friction coefficient f = (Torque)/(Radius*Static load) f startup Original bearing fbreakaway=tbreakaway/rw Torque meter Torque to turn manually shaft inside bearing. Differences at W/LD~20 kpa are due to wear. Tests conducted after 200 cycles of rotor start and stop. Breakaway f agrees well with f from startup tests.
10 Airborne friction factor f ~ 0.1 f for the BFB with 30µm shims is equal to that of the original bearing. f for the BFB with 50 µm shims is 15% larger than f for the original bearing. f ~ 0.04 Friction factor decreases with specific load
11 Rotordynamic test rig Oil inlet TC center housing Eddy current sensor Static load Journal BEARING Air outlet Shaft stub Accelerometer Oil outlet Turbine Squirrel housing Thermocouple cage (Soft BEARING Static load elastic (force gauge) support) Stinger connection to shaker X Y Load sensor Accelerometer Shaft speed: 50 krpm (833 Hz) Displacement amplitude: 20 µm Vertical specific load W/LD:14.3 kpa Thermocouple 5 cm Test frequency range: up to 450 Hz Dynamic load: up to 250 N
12 Parameter Identification Apply: sine sweep load excitations ( Hz), amplitude controlled (20 µm). Measure: bearing absolute accelerations and displacements relative to journal System EOM CS K X S X S 2 K X X XX jcxx KXY jc x F M A XY j ( ) ( ) X( ) K y YX jcyx KYY jc YY ( ) F C Y S K Y S A Y Y M ( ) S ( ) 2 Y j Frequency domain analysis yields stiffness and damping coefficients
13 BFB stiffnesses, K Original bearing Bearing with 30 µm shims 14.3 kpa specific X Y Bearing with 50 µm shims W/LD=14.3 kpa Shaft speed 50 krpm (833 Hz) BFB direct stiffnesses increases with excitation frequency, not significantly affected by shims
14 BFB Damping, C Original bearing Bearing with 30 µm shims 14.3 kpa specific load X Y Bearing with 50 µm shims W/LD=14.3 kpa Shaft speed 50 krpm (833 Hz) Damping C XX, along static load (X) decreases with excitation frequency. Direct damping increases modestly for shimmed BFB.
15 BFB loss factor, Proportional structural damping model C K Viscous energy dissipation (E v ) = structural material energy dissipated (E m ) over entire duration of load excitation (t=0 - t end ) tend tend T T EV z C z dt EM dt z K z t0 t0 X Y 14.3 kpa specific load t0 t t0 BFB loss factor (γ~ ) is not affected by shim thickness or rotor speed t end end z T C z T zk z dt dt Loss Bearing Factor Configuration Original m 0 krpm shims m shims 0.39 Original m shims krpm 50 m 0.43 shims
16 TC vibration measurements Original bearing Bearing with 30 µm shims Rotor on shimmed BFB does not show sub synchronous vibrations Bearing with 50 µm shims
17 FB post test inspection
18 Conclusions Shimmed (50 μm) BFB shows LARGEST DRY friction coefficient (f ~ ) Once airborne, friction factor is small [ f < ]. BFB with 50 μm shims has 15% larger f than original BFB and BFB with 30 μm shims). Rotordynamic coefficients: shim thickness does not affect BFB stiffnesses; however, it increases the damping coefficients. Shim thickness does not change the BFB loss factor γ~ ?? TC rotor supported on shimmed BFB (50 m) demonstrates operation free of sub synchronous whirl. How? Yet unknown. MS thesis will provide rationale
19 Questions(?) 19
Structural and Rotordynamic Force Coefficients of a Shimmed Bump Foil Bearing: an Assessment of a Simple Engineering Practice
Proceedings of ASME Turbo Expo 2015: Turbine Technical Conference and Exposition, June 15-19, 2015, Montreal, Canada Paper GT2015-43734 Structural and Rotordynamic Force Coefficients of a Shimmed Bump
More informationMetal Mesh Foil Gas Bearings for Oil-Free Turbomachinery
12 th National Conference on Gas Lubrication, Dry Gas Seal and Micro Gravity in China May 218 Metal Mesh Foil Gas Bearings for Oil-Free Turbomachinery An introduction to Oil-Free MTM requirements and metal
More informationIdentification of Structural Stiffness and Material Loss Factor in a Shimmed (Generation One) Bump Type Foil Bearing
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group Identification of Structural Stiffness and Material Loss Factor in a Shimmed (Generation One) Bump Type
More informationFailure of a Test Rig Operating with Pressurized Gas Bearings: a Lesson on Humility
Proceedings of ASME Turbo Expo 2015: Turbine Technical Conference and Exposition, June 15-19, 2015, Montreal, Canada GT2015-42556 Failure of a Test Rig Operating with Pressurized Gas Bearings: a Lesson
More informationNOVEL CARBON-GRAPHITE GAS BEARINGS FOR TURBOMACHINERY
May 2018 NOVEL CARBON-GRAPHITE GAS BEARINGS FOR TURBOMACHINERY Luis San Andrés Mast-Childs Chair Professor Porous Type Gas Bearings Porous type gas bushing pads Porous type gas bearings (PTGB) have sub-micron
More informationEFFECT OF LUBRICANT SUPPLY PRESSURE ON SFD PERFORMANCE: ENDS SEALED WITH O-RINGS & PISTON RINGS
May 2017 Year V EFFECT OF LUBRICANT SUPPLY PRESSURE ON SFD PERFORMANCE: ENDS SEALED WITH O-RINGS & PISTON RINGS TRC-SFD-01-17 Bonjin Koo Leping Yu Graduate Research Assistants Luis San Andrés Mast-Childs
More informationMEASUREMENTS OF ROTORDYNAMIC ROTOR SUPPORTED ON METAL MESH
ASME Turbo Expo 213 GT213 June 3-7, 213, San Antonio, Texas, USA MEASUREMENTS OF ROTORDYNAMIC RESPONSE AND TEMPERATURES IN A ROTOR SUPPORTED ON METAL MESH FOIL BEARINGS Thomas Chirathadam Southwest Research
More informationMay 2015 IDENTIFICATION OF STRUCTURAL STIFFNESS AND MATERIAL LOSS FACTOR IN A LARGE DIAMETER METAL MESH FOIL BEARING. Luis San Andrés and Travis Cable
TRC Project 32513/1519N1 May 2015 IDENTIFICATION OF STRUCTURAL STIFFNESS AND MATERIAL LOSS FACTOR IN A LARGE DIAMETER METAL MESH FOIL BEARING Luis San Andrés and Travis Cable Justification Foil bearings
More informationMay 2017 Year III A TEST RIG FOR EVALUATION OF FOIL THRUST BEARINGS: DYNAMIC STIFFNESS OF A METAL MESH THRUST FOIL BEARING TRC-B&C
TRC Project 400124-00078 TRC-B&C-02-2017 May 2017 Year III A TEST RIG FOR EVALUATION OF FOIL THRUST BEARINGS: DYNAMIC STIFFNESS OF A METAL MESH THRUST FOIL BEARING Travis Cable Graduate Research Assistant
More informationAPPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE
Colloquium DYNAMICS OF MACHINES 2012 Prague, February 7 8, 2011 CzechNC APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE Jiří Šimek Abstract: New type of aerodynamic
More informationA Test Rig for Evaluation of Thrust Bearings and Face Seals
TRC-B&C-02-2015 TRC Project 32513/1519F2 May 2015 Year II A Test Rig for Evaluation of Thrust Bearings and Face Seals Luis San Andrés, Michael Rohmer, Scott Wilkinson Justification Compressors, turbochargers,
More informationSOME INTERESTING ESTING FEATURES OF TURBOCHARGER ROTOR DYNAMICS
Colloquium DYNAMICS OF MACHINES 2013 Prague, February 5 6, 2013 CzechNC 1. I SOME INTERESTING ESTING FEATURES OF TURBOCHARGER ROTOR DYNAMICS Jiří Šimek Abstract: Turbochargers for combustion engines are
More informationMEASUREMENTS OF DRAG TORQUE AND LIFT OFF SPEED AND IDENTIFICATION OF STIFFNESS AND DAMPING IN A METAL MESH FOIL BEARING
MEASUREMENTS OF DRAG TORQUE AND LIFT OFF SPEED AND IDENTIFICATION OF STIFFNESS AND DAMPING IN A METAL MESH FOIL BEARING A Thesis by THOMAS ABRAHAM CHIRATHADAM Submitted to the Office of Graduate Studies
More informationMETAL MESH FOIL BEARINGS: PREDICTION AND MEASUREMENT OF STATIC AND DYNAMIC PERFORMANCE CHARACTERISTICS
METAL MESH FOIL BEARINGS: PREDICTION AND MEASUREMENT OF STATIC AND DYNAMIC PERFORMANCE CHARACTERISTICS A Dissertation by THOMAS ABRAHAM CHIRATHADAM Submitted to the Office of Graduate Studies of Texas
More informationMEASUREMENTS OF ROTORDYNAMIC RESPONSE IN A HIGH TEMPERATURE ROTOR SUPPORTED ON TWO METAL MESH FOIL BEARINGS
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group MEASUREMENTS OF ROTORDYNAMIC RESPONSE IN A HIGH TEMPERATURE ROTOR SUPPORTED ON TWO METAL MESH FOIL BEARINGS
More informationOn The Failure Of A Gas Foil Bearing: High Temperature Operation Without Cooling Flow
2013 ASME Turbo Expo Conference, June 3-7, 2013, San Antonio, TX On The Failure Of A Gas Foil Bearing: High Temperature Operation Without Cooling Flow Keun Ryu Assistant Professor Hanyang University Luis
More informationFurther Imbalance Response Measurements of Rotor Supported on Bump-Type Gas Foil Bearings: Operation to 50 krpm
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group Further Imbalance Response Measurements of Rotor Supported on Bump-Type Gas Foil Bearings: Operation to
More informationMeasurements of Drag Torque, Lift Off Speed and Identification of Structural Stiffness and Damping in a Metal Mesh Foil Bearing
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group Measurements of Drag Torque, Lift Off Speed and Identification of Structural Stiffness and Damping in a
More informationNotes 11. High Pressure Floating Ring Oil Seals
Notes 11. High Pressure Floating Ring Oil Seals Outer seal P a Outer seal land Oil supply (P S +P) Shaft Inner seal land Anti-rotation pin Seal loading spring Inner seal Process Gas (P S ) Fig. 1 Typical
More informationPNEUMATIC HIGH SPEED SPINDLE WITH AIR BEARINGS
PNEUMATIC HIGH SPEED SPINDLE WITH AIR BEARINGS Terenziano RAPARELLI, Federico COLOMBO and Rodrigo VILLAVICENCIO Department of Mechanics, Politecnico di Torino Corso Duca degli Abruzzi 24, Torino, 10129
More informationGas Bearings for Microturbomachinery Rotordynamic Performance & Stability
Turbomachinery Laboratory, Texas A&M University Mechanical Engineering Department Gas Bearings for Microturbomachinery Rotordynamic Performance & Stability Luis San Andrés Mast-Childs Professor ASME, STLE
More informationTest Results for Load-On-Pad and Load-Between- Pad Hybrid Flexure Pivot Tilting Pad Gas Bearings
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Test Results for Load-On-Pad and Load-Between- Pad Hybrid Flexure Pivot Tilting Pad Gas Bearings Research Progress Report
More informationIntroduction to rotordynamics and lubricated elements
August 2016 Introduction to rotordynamics and lubricated elements Dr. Luis San Andres Mast-Childs Chair Professor Turbomachinery Laboratory Texas A&M University Lsanandres@tamu.edu 1 Turbomachinery A turbomachinery
More informationAPPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE
Engineering MECHANICS, Vol. 19, 2012, No. 5, p. 359 368 359 APPLICATION OF A NEW TYPE OF AERODYNAMIC TILTING PAD JOURNAL BEARING IN POWER GYROSCOPE Jiří Šimek* New type of aerodynamic tilting pad journal
More informationExperimental Response of a Rotor Supported on Flexure Pivot Hydrostatic Pad Gas Bearings
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Experimental Response of a Rotor Supported on Flexure Pivot Hydrostatic Pad Gas Bearings Research Progress Report to the
More informationREVAMPING AND PRELIMINARY OPERATION OF A THRUST BEARING TEST RIG
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group REVAMPING AND PRELIMINARY OPERATION OF A THRUST BEARING TEST RIG Research Progress Report to TAMU Turbomachinery
More informationExperimental research on dynamic characteristics of gas bearing-rotor with different radial clearances
Experimental research on dynamic characteristics of gas bearing-rotor with different radial clearances Long Hao 1, Jinfu Yang 2, Dongjiang Han 3, Changliang Tang 4 Institute of Engineering Thermophysics,
More informationThermohydrodynamic Analysis of Bump Type Gas Foil Bearings: A Model Anchored to Test Data
June 211 - Update Thermohydrodynamic Analysis of Bump Type Gas Foil Bearings: A Model Anchored to Test Data Luis San Andrés Mast-Childs Professor Tae Ho Kim Post-Doc Research Associate Keun Ryu PhD Research
More informationDetermination of the Lift-Off Speed in Foil Bearings Using Various Measurement Methods
Mechanics and Mechanical Engineering Vol., No. (08) 45 44 c Lodz University of Technology Determination of the Lift-Off Speed in Foil Bearings Using Various Measurement Methods Pawe l Bagiński Grzegorz
More informationTilting Pad Journal Bearings
Tilting Pad Journal Bearings Types W140 and W141 Diameter Range 40 355 mm Standard GTW Tilting Pad Journal Bearings type W140 with 4-pads and W141 with 5-pads. These bearings are used in high speed machines,
More informationCHAPTER 1. Introduction and Literature Review
CHAPTER 1 Introduction and Literature Review 1.1 Introduction The Active Magnetic Bearing (AMB) is a device that uses electromagnetic forces to support a rotor without mechanical contact. The AMB offers
More informationMechanical Engineering Department Texas A&M University. 2004/2005 Research Progress Report Tribology Group. Year XIV
Mechanical Engineering Department Texas A&M University 2004/2005 Research Progress Report Tribology Group Year XIV 25 th Annual Turbomachinery Research Consortium Meeting May 2005 Luis San Andrés Leader
More informationDynamic Coefficients in Hydrodynamic Bearing Analysis Steven Pasternak C.O. Engineering Sleeve and Sleevoil Bearings 8/10/18 WP0281
Dynamic Coefficients in Hydrodynamic Bearing Analysis Steven Pasternak C.O. Engineering Sleeve and Sleevoil Bearings 8/10/18 WP0281 Hydrodynamic Bearing Basics Hydrodynamic journal bearings operate by
More informationMEASUREMENTS OF ROTORDYNAMIC PERFORMANCE IN A HOT ROTOR-GAS FOIL BEARING SYSTEM
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory MEASUREMENTS OF ROTORDYNAMIC PERFORMANCE IN A HOT ROTOR-GAS FOIL BEARING SYSTEM Research Progress Report to the Turbomachinery
More informationYear I. TRC-SEAL Luis San Andrés. Weilian Shan Graduate Research Assistant. May rd Turbomachinery Research Consortium Meeting
33 rd Turbomachinery Research Consortium Meeting Predictions vs. Test Results for Leakage and Force Coefficients of a Fully Partitioned Pocket Damper Seal and a Labyrinth Seal Limitations of the Current
More informationCurrent Developments in Gas Bearings for Microturbomachinery
Turbomachinery Laboratory, Texas A&M University Mechanical Engineering Department Current Developments in Gas Bearings for Microturbomachinery Luis San Andrés Mast-Childs Professor October 2007 CIBIM 8
More informationExperimental Response of a Rotor Supported on Rayleigh Step Gas Bearings
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Experimental Response of a Rotor Supported on Rayleigh Step Gas Bearings Research Progress Report to the Turbomachinery
More informationMEASUREMENTS OF LEAKAGE, POWER LOSS AND ROTORDYNAMIC FORCE COEFFICIENTS IN A HYBRID BRUSH SEAL
i MEASUREMENTS OF LEAKAGE, POWER LOSS AND ROTORDYNAMIC FORCE COEFFICIENTS IN A HYBRID BRUSH SEAL A Thesis by JOSE ENRIQUE BAKER Submitted to the Office of Graduate Studies of Texas A&M University in partial
More informationDynamic tests of SRIM fluid viscous dampers
Dynamic tests of SRIM fluid viscous dampers D. FENG & Y. SASAKI Fujita Corp., Tokyo, Japan. N. YAMAZAKI & M. ISHIYAMA Nippon Chuzo Co., Ltd., Kawasaki, Japan W. ZHU Shanghai Research Institute of Materials,
More informationON THE DETERMINATION OF BEARING SUPPORT PEDESTAL STIFFNESS USING SHAKER TESTING
ON THE DETERMINATION OF BEARING SUPPORT PEDESTAL STIFFNESS USING SHAKER TESTING R. Subbiah Siemens Energy, Inc., 4400 Alafaya trail, Orlando FL 32817 USA Abstract An approach that enables rotor dynamists
More informationROTORDYNAMIC PERFORMANCE OF A ROTOR SUPPORTED BY THREE PAD HYBRID AIR FOIL BEARING WITH CONTROLLED AIR INJECTION SANDESH GUDEMANE
ROTORDYNAMIC PERFORMANCE OF A ROTOR SUPPORTED BY THREE PAD HYBRID AIR FOIL BEARING WITH CONTROLLED AIR INJECTION by SANDESH GUDEMANE Presented to the Faculty of the Graduate School of The University of
More informationMICRO TURBOMACHINERY Applications
Turbomachinery Laboratory, Texas A&M University Mechanical Engineering Department MICRO TURBOMACHINERY Applications Luis San Andrés Mast-Childs Professor August 2010 http://rotorlab.tamu.edu MICROTURBOMACHINERY
More informationSimulation and Analysis of Vehicle Suspension System for Different Road Profile
Simulation and Analysis of Vehicle Suspension System for Different Road Profile P.Senthil kumar 1 K.Sivakumar 2 R.Kalidas 3 1 Assistant professor, 2 Professor & Head, 3 Student Department of Mechanical
More informationHYBRID GAS BEARINGS WITH CONTROLLED SUPPLY PRESSURE TO ELIMINATE ROTOR VIBRATIONS WHILE CROSSING SYSTEM CRITICAL SPEEDS
HYBRID GAS BEARINGS WITH CONTROLLED SUPPLY PRESSURE TO ELIMINATE ROTOR VIBRATIONS WHILE CROSSING SYSTEM CRITICAL SPEEDS A Thesis by KEUN RYU Submitted to the Office of Graduate Studies of Texas A&M University
More informationResearch on vibration reduction of multiple parallel gear shafts with ISFD
Research on vibration reduction of multiple parallel gear shafts with ISFD Kaihua Lu 1, Lidong He 2, Wei Yan 3 Beijing Key Laboratory of Health Monitoring and Self-Recovery for High-End Mechanical Equipment,
More informationThrowback Thursday :: Bently Nevada Dual Probe Versus Shaft Rider
Throwback Thursday :: Bently Nevada Dual Probe Versus Shaft Rider Date : February 12, 2015 Bently Nevada has a rich history of machinery condition monitoring experience and has always placed a high priority
More information0 INTRODUCTION TO FLUID FILM BEARINGS AND SEALS
Notes 0 INTRODUCTION TO FLUID FILM BEARINGS AND SEALS A turbomachinery is a rotating structure where the load and/or the driver handle a process fluid from which power is extracted or delivered to. Examples
More informationCase study on Carbon Fiber spring suspension for FORD ENDEVOUR THUNDER+
Case study on Fiber spring suspension for FORD ENDEVOUR THUNDER+ Krishna Balamurali (M.S Automotive Engineering) Principal Engineer, NV Dynamnics Abstract: Most of the SUV s (sports utility vehicles) available
More informationMARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS
POLISH MARITIME RESEARCH Special Issue 2018 S2 (98) 2018 Vol. 25; pp. 30-34 10.2478/pomr-2018-0070 MARINE FOUR-STROKE DIESEL ENGINE CRANKSHAFT MAIN BEARING OIL FILM LUBRICATION CHARACTERISTIC ANALYSIS
More informationCustomer Application Examples
Customer Application Examples The New, Powerful Gearwheel Module 1 SIMPACK Usermeeting 2006 Baden-Baden 21. 22. March 2006 The New, Powerful Gearwheel Module L. Mauer INTEC GmbH Wessling Customer Application
More informationTHE APPLICATION OF WHOLE ENGINE FINITE ELEMENT MODEL ON CRITICAL SPEED ANALYSIS FOR THE COMMERCIAL AERO-ENGINE ROTOR
THE APPLICATION OF WHOLE ENGINE FINITE ELEMENT MODEL ON CRITICAL SPEED ANALYSIS FOR THE COMMERCIAL AERO-ENGINE ROTOR Huiying Song, Shaohui Wang, Kai Sun and Shoufeng Hu AVIC Commercial Aircraft Engine
More informationInvestigations of Oil Free Support Systems to Improve the Reliability of ORC Hermetic High Speed Turbomachinery
Mechanics and Mechanical Engineering Vol. 15, No. 3 (2011) 355 365 c Technical University of Lodz Investigations of Oil Free Support Systems to Improve the Reliability of ORC Hermetic High Speed Turbomachinery
More informationMotor Technologies Motor Sizing 101
Motor Technologies Motor Sizing 101 TN-2003 REV 161221 PURPOSE This technical note addresses basic motor sizing with simple calculations that can be done to generally size any motor application. It will
More informationDesign and Test of Transonic Compressor Rotor with Tandem Cascade
Proceedings of the International Gas Turbine Congress 2003 Tokyo November 2-7, 2003 IGTC2003Tokyo TS-108 Design and Test of Transonic Compressor Rotor with Tandem Cascade Yusuke SAKAI, Akinori MATSUOKA,
More informationTechnology Readiness of 5 th and 6 th Generation Compliant Foil Bearing for 10 MWE S CO 2 Turbomachinery Systems
Technology Readiness of 5 th and 6 th Generation Compliant Foil Bearing for 10 MWE S CO 2 Turbomachinery Systems H. Heshmat, J. F. Walton and J. L. Cordova The 6 th International Supercritical CO 2 Power
More informationOBSERVATIONS ABOUT ROTATING AND RECIPROCATING EQUIPMENT
OBSERVATIONS ABOUT ROTATING AND RECIPROCATING EQUIPMENT Brian Howes Beta Machinery Analysis, Calgary, AB, Canada, T3C 0J7 ABSTRACT This paper discusses several small issues that have occurred in the last
More informationGEARBOX NOISE AND VIBRATION INFLUENCE OF BEARING PRELOAD
GEARBOX NOISE AND VIBRATION INFLUENCE OF BEARING PRELOAD Mats Åkerblom * and Ulf Sellgren *KTH Dep. of Machine Design SE-100 44 Stockholm Sweden *Volvo CE Component Division, SE-631 85 Eskilstuna, Sweden,
More informationROTATING MACHINERY DYNAMICS
Pepperdam Industrial Park Phone 800-343-0803 7261 Investment Drive Fax 843-552-4790 N. Charleston, SC 29418 www.wheeler-ind.com ROTATING MACHINERY DYNAMICS SOFTWARE MODULE LIST Fluid Film Bearings Featuring
More informationGallery of Charts Created by XLRotor
Gallery of Charts Created by XLRotor What follows are samples of the charts created automatically by XLRotor. The formats for each chart are copied from templates in a file named XLRGRPH.XLS located in
More informationFSI and Modal Analysis of Elastic Ring Squeeze Film Damper for Small Gas Turbine Engines
FSI and Modal Analysis of Elastic Ring Squeeze Film Damper for Small Gas Turbine Engines Thennavarajan Subramanian 1*, Jeyaraj P 2, Manikandan L P 3, S S Kulkarni 4, Soumendu Jana 5 Technical Officer,
More informatione-boosters, turbine generators, and turbocharger technology
e-boosters, turbine generators, and turbocharger technology About Aeristech High-performance electric machines Electric/aero integration and optimisation Power electronics design and prototyping Rotordynamics
More informationPrototyping of Radial and Thrust Air Bearing for Micro Gas Turbine
Proceedings of the International Gas Turbine Congress 2003 Tokyo November 2-7, 2003 DRAFT IGTC2003Tokyo TS-019 Prototyping of Radial and Thrust Air Bearing for Micro Gas Turbine Susumu KITAZAWA, Shigehiko
More informationXLTRC 2 TURBOMACHINERY RESEARCH CONSORTIUM ROTORDYNAMICS SOFTWARE SUITE
XLTRC 2 TURBOMACHINERY RESEARCH CONSORTIUM ROTORDYNAMICS SOFTWARE SUITE WHAT IS XLTRC2? XLTRC2 is a suite of very fast, accurate and experimentally verified, and user- friendly codes for executing a complete
More informationEDDY CURRENT DAMPER SIMULATION AND MODELING. Scott Starin, Jeff Neumeister
EDDY CURRENT DAMPER SIMULATION AND MODELING Scott Starin, Jeff Neumeister CDA InterCorp 450 Goolsby Boulevard, Deerfield, Florida 33442-3019, USA Telephone: (+001) 954.698.6000 / Fax: (+001) 954.698.6011
More informationDynamic Responses of Rotor Drops onto Auxiliary Bearing with the Support of Metal Rubber Ring
Send Orders for Reprints to reprints@benthamscience.ae The Open Mechanical Engineering Journal, 215, 9, 157-161 157 Open Access Dynamic Responses of Rotor Drops onto Auxiliary Bearing with the Support
More informationStorvik HAL Compactor
Storvik HAL Compactor Gunnar T. Gravem 1, Amund Bjerkholt 2, Dag Herman Andersen 3 1. Position, Senior Vice President, Storvik AS, Sunndalsoera, Norway 2. Position, Managing Director, Heggset Engineering
More informationMagnetic Bearings for Supercritical CO2 Turbomachinery
The 6 th International Supercritical CO 2 Power Cycles Symposium March 27-29, 2018, Pittsburgh, Pennsylvania Magnetic Bearings for Supercritical CO2 Turbomachinery Richard Shultz Chief Engineer Waukesha
More informationFlywheel Energy Storage System with AMB s and Hybrid Backup Bearings
Flywheel Energy Storage System with AMB s and Hybrid Backup Bearings Patrick McMullen and Vinh Vuong Lawrence Hawkins Vycon Inc. Calnetix Inc. 1288 Moore Street 1288 Moore Street Cerritos, CA 973, USA
More informationCornering & Traction Test Rig MTS Flat-Trac IV CT plus
Testing Facilities Cornering & Traction Test Rig MTS Flat-Trac IV CT plus s steady-state force and moment measurement dynamic force and moment measurement slip angel sweeps tests tractive tests sinusoidal
More informationPrediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM
Prediction of Thermal Deflection at Spindle Nose-tool Holder Interface in HSM V Prabhu Raja, J Kanchana, K Ramachandra, P Radhakrishnan PSG College of Technology, Coimbatore - 641004 Abstract Loss of machining
More informationImprovements for Ver November 23, 2017
Dyrobes Rotordynamics Software dyrobes.com Improvements for Ver 20.00 November 23, 2017 Add new features in BePerf for fixed-lobe and tilting pad journal bearing design: 1) Parametric study 2) Design Comparison.
More informationEvaluating and Correcting Subsynchronous Vibration in Vertical Pumps
Dyrobes Rotordynamics Software https://dyrobes.com Evaluating and Correcting Subsynchronous Vibration in Vertical Pumps Abstract By Malcolm E. Leader, P.E. Applied Machinery Dynamics Co. Kelly J. Conner
More informationCOMPARISON OF LEAKAGE BETWEEN A
Texas A&M University Mechanical Engineering Department Turbomachinery Laboratory Tribology Group COMPARISON OF LEAKAGE BETWEEN A LABYRINTH SEAL AND AN ALL-METAL COMPLIANT GAS SEAL AT HIGH TEMPERATURE Research
More information719. Diagnostic research of rotor systems with variable inertia moment
719. Diagnostic research of rotor systems with variable inertia moment Valentinas Kartašovas 1, Vytautas Barzdaitis 2, Pranas Mažeika 3, Marius Vasylius 4 1, 2 Kaunas University of Technology, Mickevičiaus
More informationINSTABILITY OF A FLEXIBLE ROTOR PARTIALLY FILLED WITH FLUID
INSTABILITY OF A FLEXIBLE ROTOR PARTIALLY FILLED WITH FLUID Zhu Changsheng College of Electrical Engineering Zhejiang University, Hangzhou, 310027, Zhejiang, P. R. of China E-mail: cszhu@hotmail.com Tel:
More informationSelected operational Problems of high-speed Rotors supported by Gas Foil Bearings
DOI: 10.24352/UB.OVGU-2017-109 TECHNISCHE MECHANIK, 37, 2-5, (2017), 339-346 submitted: July 4, 2017 Selected operational Problems of high-speed Rotors supported by Gas Foil Bearings G. Żywica, P. Bagiński,
More informationThe Effect of Friction between a Cylindrical Guide and Magnetic Tape on Lateral Tape Motion
The Effect of Friction between a Cylindrical Guide and Magnetic Tape on Lateral Tape Motion B. and F. E. Talke Center for Magnetic Recording Research University of California, San Diego 95 Gilman Drive
More informationRotor Dynamics as a Tool for Solving Vibration Problems Malcolm E. Leader, P.E. Applied Machinery Dynamics Company
Rotor Dynamics as a Tool for Solving Vibration Problems Malcolm E. Leader, P.E. Applied Machinery Dynamics Company Introduction This paper continues the series begun in 2001 for the Vibration Institute
More informationAERODYNAMIC SUPPORT OF A BIG INDUSTRIAL TURBOBLOWER ROTOR
AERODYNAMIC SUPPORT OF A BIG INDUSTRIAL TURBOBLOWER ROTOR Šimek, J. Kozánek, J. Šafr, M.* Abstract: Aerodynamic bearing support for the rotor of a 100 kw input industrial turboblower with operational speed
More informationACOCAR active suspension
ACOCAR active suspension Bert Vandersmissen Vehicle Dynamics Expo Stuttgart, 07/05/2008 Contents Introduction Active suspension hardware Quarter car test rig Skyhook quarter car control Experimental skyhook
More informationContact Elimination in Mechanical Face Seals Using Active Control
Contact Elimination in Mechanical Face Seals Using Active Control Joshua Dayan *, Min Zou and Itzhak Green The George W. Woodruff School of Mechanical Engineering Georgia Institute of Technology Atlanta,
More informationCONTENTS. 5 BALANCING OF MACHINERY Scope Introduction Balancing Machines Balancing Procedures
CONTENTS 1 OVERVIEW.....................................................................1-1 1.1 Introduction.................................................................1-1 1.2 Organization.................................................................1-1
More informationRelevant friction effects on walking machines
Relevant friction effects on walking machines Elena Garcia and Pablo Gonzalez-de-Santos Industrial Automation Institute (CSIC) 28500 Madrid, Spain email: egarcia@iai.csic.es Key words: Legged robots, friction
More informationIJTC STABILITY ANALYSIS OF A HIGH SPEED AUTOMOTIVE TURBOCHARGER. Dyrobes Rotordynamics Software
Dyrobes Rotordynamics Software http://dyrobes.com Proceedings of IJTC26 STLE/ASME international Joint Tribology Conference October 22-25, 26, San Antonio, TX, USA STABILITY ANALYSIS OF A HIGH SPEED AUTOMOTIVE
More informationECE 325 Electric Energy System Components 6 Three Phase Induction Motors. Instructor: Kai Sun Fall 2016
ECE 325 Electric Energy System Components 6 Three Phase Induction Motors Instructor: Kai Sun Fall 2016 1 Content (Materials are from Chapters 13-15) Components and basic principles Selection and application
More informationExternally Pressurized Bearings and Machinery Diagnostics
D23 Externally Pressurized MD.qxd 9/1/22 11:17 AM Page 499 499 Chapter 23 Externally Pressurized Bearings and Machinery Diagnostics IN PREVIOUS SECTIONS OF THIS BOOK, we have discussed machinery diagnostics
More informationBalancing with the presence of a rub
Balancing with the presence of a rub Nicolas Péton 1 1 GE Measurement & Control, 14 rue de la Haltinière, CS 10356, 44303 Nantes, Cedex 3, France Abstract During commissioning of a cogeneration plant the
More information1838. Experimental investigation of rotordynamic coefficients for the labyrinth seals with and without shunt injection
1838. Experimental investigation of rotordynamic coefficients for the labyrinth seals with and without shunt injection Dan Sun 1, Shuang Wang 2, Yanting Ai 3, Hailun Zhou 4, Keming Wang 5 Liaoning Key
More informationTechnology Presentation Level 2 Turbo Molecular Vacuum Pump
Magnetal has patented solutions for unique passive magnetic bearings that enables and improves high speed operation Technology Presentation Level 2 Turbo Molecular Vacuum Pump 2009-09 09-0202 Magnetal
More informationA Different Perspective of Synchronous Thermal Instability of Rotating Equipment (STIR) Yve Zhao Staff Machinery Engineer 3/15/2017
A Different Perspective of Synchronous Thermal Instability of Rotating Equipment (STIR) Yve Zhao Staff Machinery Engineer 3/15/2017 Introduction As compression technology development is driven by the market
More informationTHE INFLUENCE OF THE WHEEL CONICITY ON THE HUNTING MOTION CRITICAL SPEED OF THE HIGH SPEED RAILWAY WHEELSET WITH ELASTIC JOINTS
THE INFLUENCE OF THE WHEEL CONICITY ON THE HUNTING MOTION CRITICAL SPEED OF THE HIGH SPEED RAILWAY WHEELSET WITH ELASTIC JOINTS DANIEL BALDOVIN 1, SIMONA BALDOVIN 2 Abstract. The axle hunting is a coupled
More informationTURBOGENERATOR DYNAMIC ANALYSIS TO IDENTIFY CRITICAL SPEED AND VIBRATION SEVERITY
U.P.B. Sci. Bull., Series D, Vol. 77, Iss. 3, 2015 ISSN 1454-2358 TURBOGENERATOR DYNAMIC ANALYSIS TO IDENTIFY CRITICAL SPEED AND VIBRATION SEVERITY Claudiu BISU 1, Florian ISTRATE 2, Marin ANICA 3 Vibration
More informationVibration damping precision couplings
Vibration damping precision couplings In light of the advantages of elasticity, strength, resilience, and damping effects, elastomer materials are now being used in most areas of mechanical engineering.
More informationI. Tire Heat Generation and Transfer:
Caleb Holloway - Owner calebh@izzeracing.com +1 (443) 765 7685 I. Tire Heat Generation and Transfer: It is important to first understand how heat is generated within a tire and how that heat is transferred
More informationMeasuring the performance of a novel fluid film bearing supporting a rotor on a stationary shaft, by non-contacting means
143 Measuring the performance of a novel fluid film bearing supporting a rotor on a stationary shaft, by non-contacting means J K Martin Department of Environmental and Mechanical Engineering, The Open
More informationMEASUREMENTS VERSUS PREDICTIONS FOR A HYBRID (HYDROSTATIC PLUS HYDRODYNAMIC) THRUST BEARING FOR A RANGE OF ORIFICE DIAMETERS.
MEASUREMENTS VERSUS PREDICTIONS FOR A HYBRID (HYDROSTATIC PLUS HYDRODYNAMIC) THRUST BEARING FOR A RANGE OF ORIFICE DIAMETERS A Thesis by PAUL ROBERT ESSER Submitted to the Office of Graduate Studies of
More informationCHAPTER 6 MECHANICAL SHOCK TESTS ON DIP-PCB ASSEMBLY
135 CHAPTER 6 MECHANICAL SHOCK TESTS ON DIP-PCB ASSEMBLY 6.1 INTRODUCTION Shock is often defined as a rapid transfer of energy to a mechanical system, which results in a significant increase in the stress,
More informationStability Analysis of a Turbocharger for Marine Diesel Engine Service. Master of Science in Mechanical Engineering
Stability Analysis of a Turbocharger for Marine Diesel Engine Service by Michael S. Adams Thesis submitted to the Faculty of the Virginia Polytechnic Institute and State University in partial fulfillment
More informationConstructive Influences of the Energy Recovery System in the Vehicle Dampers
Constructive Influences of the Energy Recovery System in the Vehicle Dampers Vlad Serbanescu, Horia Abaitancei, Gheorghe-Alexandru Radu, Sebastian Radu Transilvania University Brasov B-dul Eroilor nr.
More informationDYNAMIC ANALYSIS OF A TURBOCHARGER IN FLOATING BUSHING BEARINGS
Dyrobes Rotoynamics Software https://dyrobes.com ISCORMA-3, Cleveland, Ohio, 19-23 September 2005 DYNAMIC ANALYSIS OF A TURBOCHARGER IN FLOATING BUSHING BEARINGS Edgar J. Gunter RODYN VIBRATION ANALYSIS,
More information