POWR-GARD Relay Testing Equipment PGT-0400 Series Ground-Fault Relay Test Unit PGT Ground-Fault Relay Test Unit
|
|
- Bennett Freeman
- 5 years ago
- Views:
Transcription
1 POWR-GARD Relay Testing Equipment Series Ground-Fault Relay Test Unit Ground-Fault Relay Test Unit AUGUST 7, 2009 REVISION 0 POWR-GARD GROUND-FAULT RELAY UNIT SERIES AMPERES THERMAL LIMIT USE SWITCHES LABELED AMPERES SET MAGNITUDE (0.5 A) OF OUTPUT CURRENT. USE SWITCHES LABELED SECONDS SET DURATION (0. s) OF OUTPUT CURRENT. PRESS INITIATE OUTPUT CURRENT. DISPLAY INDICATES MAGNITUDE OF OUTPUT CURRENT FOR DURATION OF OUTPUT. SET SWITCHES LABELED SECONDS 0.0 FOR MANUAL CONTROL OF OUTPUT DURATION. PUSH SWITCH OUTPUT ON OR OFF. AMPERES SECONDS Copyright 2009 by Littelfuse, Inc. All rights reserved. Publication: -M Document: P95-C Printed in Canada.
2 Page i TABLE OF CONTENTS Page Table of Contents... i List of Figures... i. GENERAL INDICATION.... THERMAL LIMIT INSTALLATION PROCEDURE TROUBLESHOOTING SPECIFICATIONS... 4 LIST OF FIGURES Page. Simplified Block Diagram Outline and Mounting Details Panel-Mounting Procedure Typical Connection Diagrams... DISCLAIMER Specifications are subject to change without notice. Littelfuse, Inc. is not liable for contingent or consequential damages, or for expenses sustained as a result of a malfunction, incorrect application, or incorrect adjustment. Pub. -M. August 7, Littelfuse POWR-GARD
3 Page. GENERAL The is an ac current source with a programmable output. The magnitude and duration of the output burst can be selected with front-panel thumbwheel switches so that ground-fault-relay coordination can be confirmed at the push of a button. The current output is transformer isolated from control power. A simplified block diagram of the is shown in Fig.. 2. INDICATION The two-digit LED display indicates the magnitude of the output current for the duration of the output burst. The center decimal point serves as a control power indicator. The decimal point on the right side of the display is used to indicate the thermal limit condition. 4. INSTALLATION outline and mounting details are shown in Fig. 2. Panel-mounting procedures are shown in Fig.. Connect 20-Vac supply voltage to and. Connect ground terminal to ground. Loop a test wire through the windows of the ground-fault CT's. Connect one end of the test wire to terminal OP and the other end to terminal OP2. For lead lengths under 40 ft, use 4 gauge wire. For lead lengths over 40 ft and less than 0 ft, use 2 gauge wire. If remote operation is required, connect a normally open contact across RMT and. Low-level contacts are recommended. Typical connection diagrams are shown in Fig. 4.. THERMAL LIMIT When the is used in the continuous output mode, the internal circuit temperature may reach the thermal limit temperature. To prevent damage to the the current output is disabled and the thermal limit indicator comes on. The output remains disabled until the temperature has fallen to a safe level at which time the thermal limit indicator turns off and the output is enabled. BUTN TIMER TIME ADJUST (0.0 SEC FOR CONTINUOUS) AC REFERENCE DERIVED FROM AC LINE INPUT AGC CURRENT LEVEL ADJUST + - OUTPUT DRIVE CIRCUITRY TRANSFORMER ISOLATION LOAD CONTROL FEEDBACK FIGURE. Simplified Block Diagram. Pub. -M. August 7, Littelfuse POWR-GARD
4 Page 2.4 (0.) 4.0 (4.09) 9.7 (.6) 9.7 (5.50).2 (0.2) POWR-GARD GROUND-FAULT RELAY UNIT SERIES F 22.7 (.7) 2.4 (.60) RMT OP OP2 AMPERES THERMAL LIMIT AMPERES SECONDS REAR VIEW PANEL THICKNESS.6 (0.06) 4. (0.9) SIDE VIEW FRONT VIEW 4. (0.56) 6.5 (2.50) M4 OR -2 TAP (NOTE 2) REAR PANEL OUTLINE SURFACE MOUNT 5.0 (0.20) 20.2 (.00) NOTES:. DIMENSIONS IN MILLIMETERS (INCHES). 2. MOUNTING SCREWS: M4 x OR -2 x BEZEL OUTLINE (0.) (0.) 2.5 (0.) 9.4 (.7) 9. (.67) 76.2 (.00) R=2.2 (0.09) R=4. (0.9) MAXIMUM 2.5 (0.).2.2 (0.2) (0.2) PANEL-MOUNT CUUT 95.0 (7.6) (0.25) (7.7) (0.25) 22.7 (.7) FIGURE 2. Outline and Mounting Details. Pub. -M. August 7, Littelfuse POWR-GARD
5 Page Step Step 2 Step RMT 2 OP OP RMT OP OP RMT 9 OP 2 OP2 The may be panel mounted without disassembly. NOTE: Remove plug-in terminal block before installing through panel. FIGURE. Panel-Mounting Procedure. PGC-5000 SERIES NEUTRAL FROM POWER SOURCE LOAD PGR-50 SENSING RESISR TERMINAL N L N NGR REMOTE INPUT 9 OP OP2 2 5 RMT I R REMOTE 9 L N R2 PGR-4704 /N OP OP2 2 L N 5 RMT 4 5 S S2 NOTE: FOR DEVICES WITH LOWER TRIP LEVELS SUCH AS THE PGR-4704 USE THE CIRCUIT AT RIGHT. RESISRS R AND R2 WILL LOWER CURRENT OUTPUT OF THE % OF SETTING. R =, W, % R2=0.,W,% I = / SETTING FIGURE 4. Typical Connection Diagrams. Pub. -M. August 7, Littelfuse POWR-GARD
6 Page 4 5. PROCEDURE Set the required output current level 0.5 to A. The recommended test current is 20% of the ground-fault trip level of device being tested. Set the output duration 0. to s or 0.0 for push on, push off operation. Press the button. If the ground-fault fails to trip, increase either the current level or time duration, and repeat the test until a trip occurs. 6. TROUBLESHOOTING Problem: No current output when the button is pressed. Possible Causes: Loose output connections. Resistance of the output wire is too high. VA requirement of the load is too high. Current is set to less than 0.4 A. No control power. Exceeded thermal limit. Troubleshooting: Check the operation by connecting a short length of wire across the output terminals and pressing the button. If using a remote test switch, check remote switch operation and connection to the. 7. TECHNICAL SPECIFICATIONS Input Voltage...20 Vac, 60 Hz, 0 VA Output Current Setting A Output Duration Setting s or continuous Output Voltage Vac maximum Shipping Weight kg (4. lb) Dimensions: Height mm (.7 ) Width mm (4. ) Depth mm (5.62 ) Environment: Operating Temperature..-40 to 60 C Storage Temperature to 0 C Pub. -M. August 7, Littelfuse POWR-GARD
SE-400 MANUAL GROUND-FAULT-RELAY TEST UNIT
3714 Kinnear Place Saskatoon, SK Canada S7P 0A6 Ph: (306) 373-5505 Fx: (306) 374-2245 www.littelfuse.com/relayscontrols SE-400 MANUAL GROUND-FAULT-RELAY TEST UNIT Revision 1-A-072115 LITTELFUSE STARTCO
More informationSE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR
SE-125 MANUAL GROUND-FAULT GROUND-CHECK MONITOR FEBRUARY 14, 2001 REVISION 3 Publication: SE-125-M Document: S95-C125-00000 Printed in Canada. Copyright 2001 by Startco Engineering Ltd. All rights reserved.
More informationSE-100T MANUAL GROUND-FAULT-RELAY TESTER
3714 Kinnear Place Saskatoon, SK Canada S7P 0A6 Ph: (306) 373-5505 Fx: (306) 374-2245 www.littelfuse.com/relayscontrols SE-100T MAUAL GROUD-FAULT-RELAY TESTER REVISIO 5-A-120513 C HI LO RMT L1 L2 OUTPUT
More informationGENERATOR & SINGLE-FUNCTION PROTECTION
PGR-4300 Generator Ground-Fault Relay No CTs required Provides a simple method for tripping a groundfault condition on generators Use with 3- or 4-pole transfer switches Monitors neutral-to-ground integrity
More informationSE-3SCR-LM MANUAL MOTOR LOAD MANAGER
3714 Kinnear Place Saskatoon, SK Canada S7P 0A6 Ph: (306) 373-5505 Fx: (306) 374-2245 www.littelfuse.com/relayscontrols SE-3SCR-LM MANUAL MOTOR LOAD MANAGER MARCH 5, 2013 REVISION 4 MOTOR LOAD MANAGER
More informationMODEL 422 Submersible Pump Controller
MODEL 422 Submersible Pump Controller Monitors True Motor Power (volts x current x power factor) Detects Motor Overload or Underload Operates on 120 or 240VAC, Single-phase or 3-phase Built-in Trip and
More informationPhenix Technologies Inc. 75 Speicher Drive Accident, Maryland 21520
USER S MANUAL PORTABLE HIGH CURRENT TEST SET MODEL NUMBER HC2 Version 4.0 Phenix Technologies Inc. 75 Speicher Drive Accident, Maryland 21520 Copyright Phenix Technologies, Inc. Rev 11/20/2014 nab TABLE
More informationXS500 Load Bank. Read all instructions before using the load bank. Contents
XS500 Load Bank Read all instructions before using the load bank Contents Contents... 2 1) Receiving... 4 a. Load Bank... 4 b. Manual... 4 2) Specifications... 5 a. Mechanical... 5 i. Lifting... 5 ii.
More informationPORTABLE CURRENT SOURCE FOR CIRCUIT BREAKER AND MOTOR OVERLOAD TESTING INSTRUCTION MANUAL PI-250B. Release 1.0 April 5, 2013
PORTABLE CURRENT SOURCE FOR CIRCUIT BREAKER AND MOTOR OVERLOAD TESTING INSTRUCTION MANUAL PI-250B Release 1.0 April 5, 2013 Electrical Test Instruments, Inc. 1301 Avondale Road, Suite J New Windsor, MD
More informationApplication Engineering
Application Engineering February, 2009 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital Compressor
More informationADVANCED PID TROUBLESHOOTING
ADVANCED PID TROUBLESHOOTING August 29, 2016 A KEY POINT If the drive is telling you something via a Fault, then the problem is probably not the drive. The drive is recognizing a fault and telling you
More informationORDERING INFORMATION SPECIFICATIONS APPLICATION
ORDERING INFORMATION UNIVERSAL MODELS The ordering part number for the universal model is 82UNIVERSAL. The 82UNIVERSAL comes with remote flame sense active. For internal flame sense, the supplied universal
More informationApplication Engineering
Application Engineering March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the
More informationDEEP SEA ELECTRONICS PLC
DEEP SEA ELECTRONICS PLC 703 AUTOMATIC START MODULE OPERATING INSTRUCTIONS Author:- John Ruddock 703 Operating Instructions Issue Beta1 25/08/2003 2:45 PM JR - 1 - >
More informationREVISION HISTORY REVISION HISTORY
FILTER CONTROLLER REVISION HISTORY Filter Flush Controller forms part of the Netafim range of filtration controllers all designed to make filteration more reliable and economical.. Contact any of the Netafim
More informationINSTALLATION INSTRUCTIONS FOR SYMCOM'S MODEL 777-HVR-SP ELECTRONIC OVERLOAD RELAY
CONNECTIONS INSTALLATION INSTRUCTIONS FOR SYMCOM'S MODEL 777-HVR-SP ELECTRONIC OVERLOAD RELAY BE SURE POWER IS DISCONNECTED PRIOR TO INSTALLATION!! FOLLOW NATIONAL, STATE AND LOCAL CODES! READ THESE INSTRUCTIONS
More informationSURE-TRIP OEM RELACEMENT TRIP UNIT
RMS CURRENT MEASUREMENT with SURE-TRIP OEM RELACEMENT TRIP UNIT Update Circuit Breaker Solid State Controls with SURE-TRIP LOGIC The SURE-TRIP Solid State Tripping Systems Have Been Designed, Tested And
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE DEEP SEA ELECTRONICS PLC DSE704 AUTOSTART CONTROL MODULE OPERATING MANUAL 057-042 704 Operating Instructions Issue 2.1 18/06/2007 11:27:00 JR - 1 - Deep Sea Electronics Plc
More informationSE-703 MANUAL EARTH-LEAKAGE MONITOR
3714 Kinnear Place Saskatoon, Saskatchewan Canada S7P 0A6 Ph: (306) 373-5505 Fx: (306) 374-2245 www.startco.ca SE-703 MAUAL EARTH-LEAKAGE MOITOR April 2, 2012 REVISIO 9 Copyright 2012 by Littelfuse Startco
More informationMaintenance Manual 13 AMPERE POWER SUPPLY 19A704647P1-P3. Mobile Communications LBI-31801C
C Mobile Communications 13 AMPERE POWER SUPPLY 19A704647P1-P3 CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALI- FIED PERSONNEL ONLY. TO AVOID ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER
More informationLC BATTERY CHARGER OPERATION & MAINTENANCE GUIDE
LC BATTERY CHARGER OPERATION & MAINTENANCE GUIDE SENS part number: 101194 Document revision: D DCN number: 105128 Date: 3/23/2006 1840 Industrial Circle Longmont, CO 80501 Fax: 303-678-7504 Tel: 303-678-7500
More informationENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE. GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA , USA MEMBER
ENGINE GOVERNING SYSTEMS LSM672 LOAD SHARING MODULE MEMBER GOVERNORS AMERICA CORP. 720 Silver Street Agawam, MA 01001-2907, USA LSM672 LOAD SHARING MODULE PRODUCT TECHNICAL INFORMATION PTI 4000 AUGUST
More informationSingle or Double 240VAC motor control for domestic and industrial gates and doors.
COBO30 Double 240V Motor Drive Controller Features For 240Volt Motors Auto Closing Open Only Security Closing and Extended Lock Pulse (user selectable) Travel Timer Push Button Input Photo Cell Input Option
More informationSURE TRIP RETRO KITS
RMS CURRENT MEASUREMENT with SURE TRIP RETRO KITS Circuit Breaker Solid State Controls with SURE TRIP LOGIC The Sure Trip Solid State Tripping Systems Have Been Designed, Tested And Produced To all Applicable
More informationKD LV Motor Protection Relay
1. Protection Features KD LV Motor Protection Relay Overload (for both cyclic and sustained overload conditions) Locked rotor by vectorial stall Running stall / jam Single phasing / Unbalance Earth leakage
More informationOperations Manual. Zero Speed Switch Sensor Model ZS09P
Zero Speed Switch Sensor Model ZS09P The must be referred to for correct installation. Failure to comply with the shall void all warranties and liabilities. Overview The Phares Electronics Model ZS09P
More informationTABLE OF CONTENTS. 8.3 Online Sensor Specifications. Series TS (Models TS1, TSP, TSH, TSL,TSF, TSB1, TSB2) According to Electromatic factory procedure
8.3 Online Sensor Specifications Series TS (Models TS1, TSP, TSH, TSL,TSF, TSB1, TSB2) Calibration: Accuracy: Remainder of range and other calibration material Overload protection Measuring principle Measuring
More information825-P Modular Protection System for motors Specification Guide
Specification Guide 1.0 General 1.01 The motor protection relay shall have a current operating range of 0.5 and 5000 amperes. 1.02 The motor protection relay shall provide current measurement-based protection
More informationVA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service
VA-908x Series Electric Rotary Actuators for Two-Position and Modulating Service Installation Instructions VA-908x Code No. LIT-12011566 Issued August 24, 2009 Applications The VA-908x Series Electric
More informationRVS-AX Instruction Manual
RVS-AX Analog Soft Starter 8-170A, 220-600V Instruction Manual Ver. 10/11/2009 2 Table of Content RVS-AX Instruction Manual 1. TABLE OF CONTENT 1. Table of Content...2 2. Safety & Warnings...3 2.1 Safety...3
More informationUser s Manual. Automatic Switch-Mode Battery Charger
User s Manual Automatic Switch-Mode Battery Charger IMPORTANT Read, understand, and follow these safety rules and operating instructions before using this battery charger. Only authorized and trained service
More informationP445 Series Electronic Lube Oil Control
FANs 125, 121 s Section P Product/Technical Bulletin P445 Issue Date 0100 P445 Series Electronic Lube Oil The P445 Series Electronic Lube Oil is designed for use on refrigeration compressors equipped with
More informationINSTALLATION INSTRUCTIONS FOR Owner's Copy FILTERED AND REGULATED POWER SUPPLY VOLTS DC INPUT: Hz.
103158 March 9, 2011 FOR INDOOR USE ONLY Detex Corporation, 302 Detex Drive, New Braunfels, Texas 78130-3045 (830)629-2900 / 1-800-729-3839 / Fax (830)620-6711 E-MAIL: detex@detex.com INTERNET: www.detex.com
More informationSDM72 Start on Demand Modules
Capricorn Controls DA04SDM72-2 Revised Design Page 1 of 6 SDM72 Start on Demand Modules Genset Controls - Timers - Monitors - Trips - Battery Charging - Spares & Accessories - Custom Products Application
More informationInstallation and Maintenance Instructions. World Leader in Modular Torque Limiters. PTM-4 Load Monitor
World Leader in Modular Torque Limiters Installation and Maintenance Instructions PTM-4 Load Monitor 1304 Twin Oaks Street Wichita Falls, Texas 76302 (940) 723-7800 Fax: (940) 723-7888 E-mail: sales@brunelcorp.com
More informationmodel ps600 Address all communications and shipments to: FEDERAL SIGNAL CORPORATION
MODEL: PS600 HZ: 60 A model ps600 installation and service manual for federal model ps600 FEDERAL SIGNAL CORPORATION POWER SUPPLY VOLTS: SERIES: 120VAC FEDERAL SIGNAL CORPORATION UNIVERSITY PARK, IL. U.S.A.
More informationAVR Hybrid Universal Analog Digital Voltage Regulator Operation Manual
AVR 63-12 Hybrid Universal Analog Digital Voltage Regulator Operation Manual Self Excited Automatic Voltage Regulator For use in Brushless PMG and Auxiliary Winding 1. SUMMARY The AVR 63-12 is a totally
More informationData Bulletin. Ground-Censor Ground-Fault Protection System Type GC Class 931
Data Bulletin 0931DB0101 July 2001 Cedar Rapids, IA, USA Ground-Censor Ground-Fault Protection System Type GC Class 931 09313063 GT Sensor Shunt Trip of Circuit Interrupter Window Area for Conductors GC
More informationB BASIC HEAT TREATMENT CONSOLE
Maritime Stress PO Box 2898, 30 Estates Road Dartmouth, NS, B2W 4Y2, Canada Toll Free: 1-877-468-1781 Phone: (902) 468-7873 Fax: (902) 468-2304 Website: E-mail: info@maritimestress.com OPERATION MANUAL
More informationLA Motor Protection. A South African Company to be Proud of
LA Motor Protection Relay Physical Address: 298 Soutter Street, Pretoria West Tel: 083 454 6949, +27 12 327 1729 Fax: +27 (0)12 327 1733 Toll Assist: 0860 10 30 41 www.newelec.co.za sales@newelec.co.za
More informationUNIVERSAL PUSHBUTTON DIMMER ETD 2 (Rail mount version)
UNIVERSAL PUSHBUTTON DIMMER ETD 2 (Rail mount version) With central control inputs, front button and various operating modes and functions General purpose, user-friendly electronic pushbutton dimmer for
More informationXL1000 Load Bank. Read all instructions before using the load bank. Contents
XL1000 Load Bank Read all instructions before using the load bank Contents Contents... 2 1) Receiving... 4 a. Load Bank... 4 b. Manual... 4 2) Specifications... 5 a. Mechanical... 5 i. Lifting... 5 ii.
More informationBulletin 825 SMM Smart Motor Manager
Bulletin 825 SMM Smart Motor Manager Your order must include: Cat. no. of the Smart Motor Manager selected with supply Voltage Suffix Code, Cat. no. of Converter Module selected, and, If required, Cat.
More informationRU BMS Power Supply and Battery Management System Owners Guide
RU2-4012- BMS Power Supply and Battery Management System Owners Guide (These instructions are intended for use by a technician familiar with electronic products) RU2-4012- BMS is a continuous duty power
More informationSA Power Networks Commissioning Witnessing Checklist
SA Power Networks Commissioning Witnessing Checklist CUSTOMER NAME: SOLAR PV APPROVED CAPACITY: BATTERY APPROVED CAPACITY: kw (AC) kw (AC) OPERATING PHILOSOPHY: MAXIMUM EXPORT: Non-Export/Export kw (AC)
More informationXCITE Owner s Manual. Reso-not TM Damping System XCITE 1502C HYDRAULIC POWER SUPPLY
Reso-not TM Damping System XCITE Owner s Manual 1502C HYDRAULIC POWER SUPPLY Xcite Systems Corporation 675 Cincinnati RDS Batavia - 1 Pike Cincinnati, Ohio 45245 Tel: (239) 980-9093 Fax: (239) 985-0074
More informationATyS d M Remotely operated Transfer Switching Equipment from 40 to 160 A
ATyS d M Remotely operated Transfer Switching Equipment Transfer switches new The solution for > Applications with an external ATS/AMF controller > Building Management Systems (BMS) atys-md_002_b_1_cat
More informationSetPoint 501 and 501s Controllers Installation and Operation Manual
SetPoint 501 and 501s Controllers and Operation Manual SetPoint 501s SetPoint 501 Setpoint 501 and 501s Controllers and Operation Manual is published by Uponor Wirsbo, Inc. 5925 148th Street West Apple
More informationREVISED ATM72 Auto Transfer Module
Capricorn Controls DA01ATM1-1 Data & Application Note Page 1 of 8 REVISED - - - ATM72 Auto Transfer Module Genset Controls - Timers - Monitors - Trips - Battery Charging - Spares & Accessories - Custom
More informationMANUAL ELECTRIC FIRE PUMP CONTROLLERS METRON SERIES M450
MANUAL ELECTRIC FIRE PUMP CONTROLLERS METRON SERIES M450 TABLE OF CONTENTS PART I GENERAL DESCRIPTION... PAGE 2 PART II FUNCTIONS... PAGE 2 PART III INSTALLATION... PAGE 3 PART IV INITIAL INSTALLATION
More informationSCR Power Controllers
SCR Power Controllers Instruction Manual SCR POWER CONTROLLERS TABLE OF CONTENTS General Description and Specifications...1 Firing Modes....2 Installation and Wiring...4 Operation...9 Troubleshooting...15
More informationDEEP SEA ELECTRONICS PLC
COMPLEX SOLUTIONS MADE SIMPLE. DEEP SEA ELECTRONICS PLC DSE5110 AUTOSTART CONTROL MODULE OPERATING MANUAL Deep Sea Electronics Plc Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44
More informationMODEL A96 SERIES. 130Vdc Switchmode Utility Rectifier / Battery Charger. Used with LaMarche Power Cage ECN/DATE
MODEL A96 SERIES 130Vdc Switchmode Utility Rectifier / Battery Charger Used with LaMarche Power Cage CPN112138 ECN/DATE ISSUE DATE: ECN 17010-12/05 106 BRADROCK DRIVE DES PLAINES, IL. 60018-1967 (847)
More informationSECTION MICROPROCESSOR TRIP UNITS FOR LV CIRCUIT BREAKERS. This section is organized as indicated below. Select desired Paragraphs.
SECTION 16904 MICROPROCESSOR TRIP UNITS FOR LV CIRCUIT BREAKERS PART 2 PRODUCTS 01 MANUFACTURERS A. B. C. Eaton * * The listing of specific manufacturers above does not imply acceptance of their products
More informationOPEN/CLOSE SERVICE ELECTRIC ACTUATORS OPERATION AND MAINTENANCE MANUAL COMMERCIAL AND INDUSTRIAL VALVES AND AUTOMATION
SERIES 1000-X OPEN/CLOSE SERVICE ELECTRIC ACTUATORS OPERATION AND MAINTENANCE MANUAL COMMERCIAL AND INDUSTRIAL VALVES AND AUTOMATION Publication S1000X-110 VER0215-1 For information on this product and
More informationLine Gard. Underwriters Laboratories (UL) Applicable Code Notation
Underwriters Laboratories (UL) UL 50E Enclosures for Electrical Equipment, Environmental Considerations 1.1 This standard applies to enclosures for electrical equipment intended to be installed and used
More information5. OVERCURRENT RELEASE (OCR)
5. OVERCURRENT RELEASE (OCR) Options available for the type AR ACBs include a highly reliable, multi-functional overcurrent release (OCR) with a built-in 8- bit microprocessor. This OCR is supplied with
More informationInstallation & Operation Manual. Electrak 10 Series / Electromechanical Linear Actuator
www..com Installation & Operation Manual Electrak 10 Series / Electromechanical Linear Actuator INTRODUCTION Thomson has many years of experience designing and manufacturing linear actuators for a wide
More informationABB Softstarter Benefits Charnchanok Thongprad
ABB Softstarter Benefits Charnchanok Thongprad tomation Technology Products AB Control - 1 - - Why Softstarters? Benefits for the Electrical network Reduces voltage drops on networks Minimizes starting
More informationTransmission Switching
General Application Southern States supplies a wide offering of Transmission Switching solutions in response to an increasing need for improved system reliability and reduced installation times. This range
More informationMU MMMREV.2 09/01 UNI EN ISO ELECTRONIC POWER FACTOR REGULATOR type QR INSTRUCTION MANUAL PAG. 7
MU 03.04.MMMREV.2 09/01 UNI EN ISO 9001 ELECTRONIC POWER FACTOR REGULATOR type QR INSTRUCTION MANUAL PAG. 7 ENGLISH 1. GENERAL 2. INSTALLATION MECHANICAL FIXING ELECTRICAL CONNECTIONS HOW TO CHOOSE the
More informationTypes of Motor Starters There are several types of motor starters. However, the two most basic types of these electrical devices are:
Introduction Motor starters are one of the major inventions for motor control applications. As the name suggests, a starter is an electrical device which controls the electrical power for starting a motor.
More informationTable Of Contents. Motor Selection Guide Installation Instructions Operators 20-32
Table Of Contents Motor Selection Guide 2-12 - Shades, Shutters and Doors - Retractable Awnings Installation Instructions 13-1 - Operator Adaptors - Operator Limit Adjustment - Wiring Considerations -
More informationCat/DCG-6D1I/07-08/03/Ver 1 Page 2/10
Cat/DCG-6D1I/07-08/03/Ver 1 Page 2/10 Index 1.1 Introduction 1.2 Salient Feature of the DGC-6D 1.2.1 Protection & Supervision 1.2.2 Measurement & Display 1.2.3 LED Indications 1.2.4 Timer 1.3 Function
More informationADVR-12. Hybrid Universal Analog Digital Voltage Regulator Operation Manual
ADVR-12 Hybrid Universal Analog Digital Voltage Regulator Operation Manual Adapter plugs for Digital Regulator Self Excited Automatic Voltage Regulator For use in Brushless PMG and Auxiliary Winding 4501
More informationFigure 1. Type CWP-1 Ground Relay (Front View) Figure 2. Type CWP-1 Ground Relay (Rear View) E
Figure 1. Type CWP-1 Ground Relay (Front View) Figure 2. Type CWP-1 Ground Relay (Rear View) 41-242.5E 2 Typical 60 Hertz time product curves for the type CWP-1 relay are shown in Figure 4 with 100 volts
More informationNIGHT-LITE PRO II. Electrical System Troubleshooting Guide and Procedures
NIGHT-LITE PRO II Electrical System Troubleshooting Guide and Procedures Allmand Bros. Inc. PO Box 888 1502 W. 4 th Ave. Holdrege NE 68949 USA 308-995-4495 Phone 800-562-1373 Toll-Free www.allmand.com
More informationLESTRONIC II BATTERY CHARGER BUILT-IN OR PORTABLE CHARGERS
LESTRONIC II BATTERY CHARGER BUILT-IN OR PORTABLE CHARGERS PLEASE SAVE THESE IMPORTANT SAFETY AND OPERATING INSTRUCTIONS For correct operation of the equipment, it is important to read and be familiar
More informationInstallation and Construction Notes for EVSE4
Installation and Construction Notes for EVSE4 You need to read and understand this if you want to build an EVSE that will be safe and need to pass a building inspectors review. Before beginning this process
More information5. OVERCURRENT RELEASE (OCR)
5. OVERCURRENT RELEASE (OCR) Options available for the type AR ACBs include a highly reliable, multi-functional overcurrent release (OCR) with a built-in 8- bit microprocessor. This OCR is supplied with
More informationAQUASTAR C6. (Comfort 6000) Next Generation Auto Backwash Valve System. (selectable time-pressure or remote cycle start)
AQUASTAR C6 (Comfort 6000) Next Generation Auto Backwash Valve System (selectable time-pressure or remote cycle start) SIDE MOUNTED AND TOP MOUNTED VALVES WITH QUICK INSTALL ELECTRIC ACTUATORS FOR PIPE
More information1 AMP CURRENT SOURCE
1 AMP CURRENT SOURCE CS-2000-U CS-2000-E USER MANUAL BC BIOMEDICAL CS-2000 SERIES TABLE OF CONTENTS WARNINGS, CAUTIONS, NOTICES... ii DESCRIPTION... 1 LAYOUT... 2 OPERATION... 4 TESTING... 6 MANUAL REVISIONS...
More informationSelf-Testing Industrial Series
Series: AS-I (Maint.-Free) Self-Testing Industrial Series Emergency Lighting Equipment Instructions for INSTALLATION OPERATION SERVICE SPECIFICATIONS 1300650 1300654 1300666 1300754 1300823 1300886 Hubbell
More informationTOTALINE PROTECTION CONTROLS
TOTALINE PROTECTION CONTROLS SOLID STATE HEAD PRESSURE CONTROL WITH OPTIONAL HEAT PUMP OVERRIDE Head Pressure Controls Temperature sensitive fan motor control which regulates head pressure at low ambients
More informationNet Metering Interconnection Requirements
Net Metering Interconnection Requirements Customer Generation Capacity Not Exceeding 100 kw Date: 2017-07-01 Version: 1 Revision History Date Rev. Description July 1, 2017 1 Initial Release Newfoundland
More informationSingle Pole Circuit Protectors 55. Multi-Pole Circuit Protectors 56. Configurations 58. Operating Characteristics 59.
Single Pole Circuit Protectors 55 Multi-Pole Circuit Protectors 56 Configurations 58 Operating Characteristics 59 Delay Curves 60 Specifications 61 Decision Tables 62 SINGLE POLE CIRCUIT PROTECTORS The
More informationWorld Leaders in Diesel Fuel Injection Test Equipment. IFT-c. Injector Function Tester Controller. Operating and Servicing Manual
World Leaders in Diesel Fuel Injection Test Equipment. IFT-c Injector Function Tester Controller Operating and Servicing Manual HL048 (EN) Issue 4, H1852, August 2011 HARTRIDGE LIMITED IFT-c Operating
More informationFC/FCA 12, 24, 32 & 48 VOLT, 6 & 10 AMP BATTERY CHARGER OPERATION & MAINTENANCE GUIDE
FC/FCA 12, 24, 32 & 48 VOLT, 6 & 10 AMP BATTERY CHARGER OPERATION & MAINTENANCE GUIDE SENS part number: 101037 Document revision: A Engineering change number: 105073 Date: 1/13/2006 1840 Industrial Circle
More informationProtection for 2500KVA High Tension Transformer Ankita S.Kulkarni 1, Priyanka S.Dhayarkar 2, Harsha H.Ambure 3, Ashwini S.Shinde 4
Protection for 2500KVA High Tension Transformer Ankita S.Kulkarni 1, Priyanka S.Dhayarkar 2, Harsha H.Ambure 3, Ashwini S.Shinde 4 Graduate Student, Dept. of E&TC, Pimpri Chinchwad College of Engineering,
More informationCBS 212/CBS 212A CURRENT BOOST SYSTEM
CURRENT BOOST SYSTEM APPLICATION AND FEATURES this page APPLICATION: The CBS 212 and CBS 212A Current Boost Systems are solid-state excitation support devices designed to supply 20 Amps for 10 seconds
More informationTransfer Switch TS-50. Owner s Manual
Transfer Switch TS-50 Owner s Manual Table of Contents Introduction 2 Installation 2 Operational Testing 7 Troubleshooting 7 Hi-Pot Testing 8 Generator Note 9 Medical Appliances 10 Caution 10 Disclaimer
More informationALIEM USER MANUAL R. Bocconi. REV. DATE Checked and Approved R. T.
ALIEM USER MANUAL 2 19-04-2018 R. Bocconi REV. DATE Checked and Approved R. T. PAGE INTENTIONALLY LEFT BLANK 2 ALIEM 1000 USER'S MANUAL Version 2 dated 19-04-2018 1 INTRODUCTION ALIEM 1000 is an emergency
More informationBE SURE POWER IS DISCONNECTED PRIOR TO INSALLATION! FOLLOW NATIONAL, STATE, AND LOCAL CODES! READ THESE INSTRUCTIONS ENTIRELY BEFORE INSTALLATION!
INSTALLATION INSTRUCTIONS FOR SYMCOM S MOTORSAVER MODEL 460 BE SURE POWER IS DISCONNECTED PRIOR TO INSALLATION! FOLLOW NATIONAL, STATE, AND LOCAL CODES! READ THESE INSTRUCTIONS ENTIRELY BEFORE INSTALLATION!
More informationSYMBOL LEGEND DANGER WARNING NOTE THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN
SYMBOL LEGEND DANGER THIS INDICATES DANGER TO THE LIFE AND HEALTH OF THE USER IS APPROPRIATE PRECAUTIONS ARE NOT TAKEN WARNING THIS WARNS THAT MATERIALS MAY BE DAMAGED IF APPROPRIATE PRECAUTIONS ARE NOT
More informationOTEC Transfer switch open transition
Specification sheet OTEC Transfer switch open transition 40 1200 amp Description OTEC transfer switches are designed for operation and switching of electrical loads between primary power and Standby generator
More informationZone Selective Interlock Module. For GE Circuit Breakers
GE Zone Selective Interlock Module For GE Circuit Breakers Table of Contents 1. Introduction... 4 What is Zone-Selective Interlocking (ZSI)?...4 What is a Zone-Selective Interlock Module?...4 2. Description...
More informationSECTION MOTOR CONTROL
SECTION 26 24 19 MOTOR CONTROL PART 1 - GENERAL 1.1 SECTION INCLUDES A. Manual motor starters B. Magnetic motor starters C. Combination magnetic motor starters D. Solid-state reduced voltage motor starters
More informationIOA Expansion Cabinet. Dual Line Cords Upgrade Instructions
IOA Expansion Cabinet Dual Line Cords Upgrade Instructions Notice The information contained in this document is subject to change without notice. STRATUS COMPUTER INC. MAKES NO WARRANTY OF ANY KIND WITH
More informationTDX - Taco Duplex Starter with
Energy Management TDX - Taco Duplex Starter with Smartstart The TDX extends the life of your pumps by alternating control. It comes standard with underload protection, a enhanced class 10 electronic overload
More informationMBS AG. CTB Plug-in current transformer MBS AG. Dimensions: General technical specifications:
CTB 31.35 Plug-in current transformer Dimensions: Primary conductor 1: 30x10 mm Primary conductor 2: 25x12 mm Primary conductor 3: 20x20 mm Round conductor: 26 mm Transformer width: 60 mm Transformer height:
More informationMedium Voltage Fuses
2,400-38,000 VAC General Information Current-limiting E and rated fuses are equipped with a mechanical indicator or striker pin that protrudes through the fuse cap upon operation of the fuse. This provides
More informationType DTH 31, 32 DTTM 11, 12 High Speed Biased Differential Relays
Type DTH 31, 32 DTTM 11, 12 High Speed Biased Differential Relays Type DTH 31, 32 DTTM 11, 12 High Speed Biased Differential Relays DTH relay withdrawn from case Features l High speed. l Low burden. l
More informationDART Charger Product Description, Information and Specification
g Digital Energy DART Charger Product Description, Information and Specification Document Number : PRPI-029 Version : 1.00 Revision : 2 Date : 03.02.11 Classification: NOTICE OF COPYRIGHT & PROPRIETARY
More informationMODEL UC 14YFA. Hitachi. Power Tools TECHNICAL DATA AND SERVICE MANUAL CHARGER UC 14YFA SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
MODEL UC 14YFA Hitachi Power Tools CHARGER UC 14YFA TECHNICAL DATA AND SERVICE MANUAL U LIST No. F888 Aug. 2003 SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT CONTENTS Page 1. PRODUCT NAME...1
More informationATyS S - ATyS d S Remotely operated Transfer Switching Equipment from 40 to 125 A
Transfer switches The solution for > Genset < 90 kva > Heating systems > Climate control > Ventilation systems > Telecommunications atys-s_018_a Strong points Function products are 4 pole remotely operated
More informationCat. No. I526-E1-1 USER S MANUAL 3G3IV-PLKEB2 /4. Braking Resistor Units 3G3IV-PCDBR2 B/4 B. Braking Units
Cat. No. I526-E1-1 USER S MANUAL 3G3IV-PLKEB2 /4 Braking Resistor Units 3G3IV-PCDBR2 B/4 B Braking Units Thank you for choosing an OMRON Braking Resistor Unit and Braking Unit. Proper use and handling
More informationElectronic Service Manuals
Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this document. Should you have detailed questions
More informationOPERATING INSTRUCTION: DGC-6D/6D1I
OPERATING INSTRUCTION: DGC-6D/6D1I GCB Auto Man Stop Fail - PROCOM Pvt Ltd MRM PROCOM Plot No. : 20-21, Industrial Estate, Sector - 59, Phase-II, Faridabad (Haryana) Ph.: 0129-4700400(10 Lines) Email:
More informationGrounding Of Standby & Emergency Power Systems
July / August 2007 ELECTRICAL LINE 53 Grounding Of Standby & Emergency Power Systems By Andrew Cochran Power continuity is essential in many industrial and commercial installations where a trip out due
More informationPower Switching Devices
Watlow has manufactured solid state power controllers for over forty years. Watlow s is a microprocessor-based product that features application flexibility unmatched by any other silicon controlled rectifier
More information