EU DLX LED Tail-Light Kit Installation:
|
|
- Cathleen Charles
- 5 years ago
- Views:
Transcription
1 Page EU DLX LED Tail-Light Kit Installation: First we will remove the old original flasher module. The original flasher module will be located on the driver side of the car near the fire wall as shown on the following picture. The installation procedure is as follows: 1) Remove the existing flasher module 2) Connect the new flasher wires red and greed to the Mustang s wiring previously removed. 3) Connect the black ground wire from the new LED flasher module to a good chassis grounding point. Simply unsnap the cylinder shaped module and remove the push on connectors.these will be attached with a green wire and a orange/yellow wire. The LED flasher module has three color coded wire leads. Red, Green, and Black. Once you remove the old module install the new LED flasher module by simply plugging in the red wire to the Mustang s yellow-orange wire and the green wire to the Mustang s blue ( may be green on some cars ) wire. You now have only to attach the black wire to a convenient chassis ground point. A likely place to connect the black ground wire will be under a mounting screw on the dash or on any metal part screwed under the dash. Just make sure that there is a good electrical connection between the black wire and the cars chassis. GREEN RED Be sure and wrap each connector in electrical tape before final installation of the flasher module.
2 Page 2 A likely place to connect the black ground wire will be under a mounting screw on the dash or on any metal part screwed under the dash. Just make sure that there is a good electrical connection between the black wire and the cars chassis. MODULE INSTALLATION Now install the LED taillight modules. Each module is clearly marked R for right and L for left. Be careful to install only the Left module in the Left taillight and the Right module in the right taillight. Otherwise the sequence direction will not be correct though no harm would come to the modules themselves. You will follow the procedure below for installing each LED taillight module. 1) Unscrew the small #4 screw which holds the LED board assembly onto the 1157 lamp base. The base will now be free from the board for insertion into the socket. 2) Insert the base into the existing Mustang lamp socket. Carefully align the socket pins with the slot. NOTE that the pins are offset and can only go in one way! 3) Gently push the LED taillight module into the socket making sure that the alignment pins and the socket slots are properly aligned. 4) Now push in on the base and rotate to the right to lock in the base. which protrude from the housing about 1 inch use the shorter spacer. If the original lamp sockets have been replaced use the longer spacer. 6) Slip the spacer over the supplied 1 inch screw. Which has been passed through the board just as originally supplied. 7) Re-secure the board onto the base by screwing the screw into the tapped portion of the base standoff. Be sure and align the LED module to be straight. Also be sure and check for shorts between the board and the lamp housing. 5 A. Remove lens, frame, and incandescent bulb. B. Verify that the ignition is off and that the cars lights are OFF too 5) Pick one of the attached spacers depending on the socket you have in your car. If your car has the original Ford sockets 6
3 Page 3 Connecting Braking Sensor Wire ORANGE/BLUE RED Driving Lights BLACK From LED Module GREEN/ORANGE Step 1: You must attach a wire tap connector to the ORANGE/ BLUE wire connected to the lamp socket boot connector on one side of the car as shown above. You must also attach a wire tap connector to the GREEN/ORANGE wire connected to the lamp socket boot connector on the other side of the car. Step 2: Connect the Brake Sensor wire from each module by drilling a hole in each housing and routing the sensor wire so that it can plug into the corresponding sire tap connector on the opposite side of the car. Alternate wire routing ORANGE/BLUE Alternately to avoid drilling a hole in the lamp housing the Brake sensor wire from each LED module can be routed through the housing opening in the taillight panel. Be sure and add insulating tape around the edges of the housing opening to prevent the Brake sensor wire from being cut. BLACK From LED Module GREEN/ORANGE
4 Page 4 Installing the Taillights Critical! you must remove the harness boot from the taillight housing before installing your Mustang Project LED sequential taillights. Always remove the connector boot on cars equipped with this type of connector BEFORE inserting the taillight module. It is also a good idea to apply bulb grease on the boot and connector before reinstalling the boot. The socket must move in and out. Old or corroded sockets don t move properly which can cause connection problems with the taillight modules. Bulb grease or a lubricant like PB Blaster may be require to ensure free movement of the socket before taillight module installation.
5 Page 5 Trouble Shooting Guide: Remember... you are dealing with electrical components that are over 40 years old! Our NEW improved design works as follows: With brake applied and no turn signal active. Two inner sections light full bright red. With driving lights ON and no turn signal active. Two inner sections light to half bright red. With driving lights OFF and turn signal ON. Outer amber section blinks on/off for turn signal indicaiton. With driving lights ON and turn signal ON. Outer amber section blinks ON/OFF. Two inner sections stay lit to half bright red. With brake applied and turn signal ON. Two inner sections are steady bright red the outer amber section blinks. Note: A slight blip of the red lights will be seen when the driving lights are on and the turn signal is active. This is normal operation. If you have any problems with your installation please feel free to give us a call. You can also check our webpage at for updated Trouble Shooting Guides for all of our products. Most Taillight problems are due to faulty wiring or bad socket connections. Remember unless you have replaced the wiring or taillight sockets in your Mustang you are dealing with electrical components that are over 40 years old! Corrosion and rust can take their toll. If you have any troubles first re-install the standard incandescent lamps and ensure that the signals, brake, and light functions work properly. If you see any problem with the brake or signal light functionality using the incandescent lights your system will not work with the new Mustang Project LED taillight modules. Carefully check for bad or rusted sockets. If you see evidence of corrosion carefully clean the contacts and re-test. Old wiring can also be a source of problems. Look for broken or frayed insulation if you see intermittent functionality. Below is a list of trouble shooting keys: Problem: Lights flicker. Flickering lights are often caused by failing alternators or bad regulators. The alternator may still function well enough to marginally charge the battery but diode failure in the alternator can cause flickering taillights. It is also possible that the regulator is failing. The original Mustang electromechanical regulators are famous for unusually failures. Always replace your regulator with a Motorcraft direct replacement regulator available at most auto parts stores. If you suspect a regulator or alternator problem you need to replace these items before you car is stranded! Doing so will also prevent flickering of the LED taillights. Problem: Taillights don t sequence but do light if headlights are on. Most likely this is due to a bad socket. It can also be caused by incorrect installation of the Mustang Project flasher module or improper connection of the flasher module ground. Carefully clean the socket and use a mild sandpaper on the Taillight Module contacts to clean off any debris left by a dirty socket. Problem: Taillights sequence but taillights do not illuminate when headlamps are on. Most likely this is due to a bad socket. Carefully clean the socket and use a mild sandpaper on the Taillight Module contacts to clean off any debris left by a dirty socket. Problem: Taillights function abnormally in the rain. This is probably caused by water in the Taillight bucket. Check for evidence of water and repair any gasket leaks. The Mustang Project Taillight modules are coated to protect against water damage but they will not operate if too much water is allowed to cling to the circuit boards. Problem: Taillights don t fit properly into sockets. Review the socket section at the beginning of this instruction sheet for adjustment with misaligned sockets. Be careful to always ensure that you have removed the boot connector in the back of the light housing BEFORE inserting the taillight modules. Failure to do so can cause any or all of the above symptoms!
Components included in your kit:
Page 1 Components included in your kit: The LED flasher module will replace your existing flasher module. The left and right taillight modules will replace your existing All of the equipment illustrated
More informationMUSTANG PROJECT INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR MUSTANG
VOLUME 6 Price:$9.95 MUSTANG PROJECT A SafeCode Inc. Publication INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR 64.5-66 MUSTANG Convert from original 1964.5-66 Mustang style taillights
More informationComponents included in your kit:
Page 1 Components included in your kit: All of the equipment illustrated in this manual was proudly manufactured in the USA by Mustang Project a SafeCode Inc. enterprise. For accessories and spare parts
More informationMUSTANG PROJECT. INSTALLING THE Mustang Project LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK. Price:$9.
WWW.MUSTANGPROJECT.COM VOLUME 6 Price:$9.95 A SafeCode Inc. Publication INSTALLING THE Mustang Project 1996-2004 LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK Page 2 Read these instructions
More informationConvert from original 1969 Mustang style taillights to Shelby Style!
WWW.MUSTANGPROJECT.COM VOLUME 6 Price:$9.95 MUSTANG PROJECT A SafeCode Inc. Publication INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR 69 MUSTANG Convert from original 1969 Mustang
More informationSequential Tail Light System
Sequential Tail Light System Installation Instructions Notice: Our conversion systems are intended for 1965-70 Ford Mustangs only. This is not a replacement system for Shelby Mustangs or Mercury Cougars
More informationPantera Electronics LED Taillight Conversion Installation Manual
Pantera Electronics LED Taillight Conversion Installation Manual This LED signal lamp conversion was designed to replace the incandescent lamp 1157 with a Light Emitting Diode Array designed specifically
More informationPantera Electronics LED Taillight Installation Manual
Pantera Electronics LED Taillight Installation Manual (2nd Gen) This LED signal lamp conversion was designed to replace the incandescent lamp 1157 with a Light Emitting Diode Array designed specifically
More informationClassicLEDs LLC. Sequential LED System
ClassicLEDs LLC 1967 and 1968 Mustang Sequential LED System CLE30015S Thank you for your purchase. This is the latest design of our 1967 and 1968 Mustang sequential LED system. There have been several
More informationTROUBLE SHOOTING FOR NEGATIVE GROUND TRUCKS
TROUBLE SHOOTING GUIDE TROUBLE SHOOTING FOR NEGATIVE GROUND TRUCKS IMPORTANT CAUTIONS WHEN CHECKING SENSOR SYSTEM, DO NOT HAVE VEHICLE ENGINE RUNNING EXCEPT WHERE TOLD TO DO SO. Ensure that the electrical
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More informationTurn Signal / Horn Kit PN 7101 by All years Polaris RZR 1000 and RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED
All years Polaris RZR 1000 and 1000-4 2015 RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODEL POLARIS RZR 1000 AND 1000-4. ALSO THE 2015 POLARIS RZR
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationLiteDOT Installation Document
LiteDOT Installation Document This document designed to aid in installation of LiteDOT s on Jeep TJ models, other models are similar. NOTE: Installing LiteDOT s on a Jeep where the 2 necessary mounting
More informationFORD MUSTANG. Two Panel Sequential LED Tail Light Kit Installation Guide
1967-68 FORD MUSTANG Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationINSTALLATION AND INSTRUCTION MANUAL
INSTALLATION AND INSTRUCTION MANUAL and STAR SABRE ECE Compliant Plus Lightbars PLIT429ECE REV. C 3/31/14 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring,
More informationELECTRICAL DIAGNOSTICS & OPERATION
Operation Function: Provides power to the headlights, tail lights, hazard lights, work light and dash lights in different combinations depending upon the position the light switch is placed in. Operating
More informationHOW - TO WIRING & LIGHTING
HOW - TO WIRING & LIGHTING Tool And Material Checklist Test Light Service Manual Penetrating Oil Long-Nose Pliers T-Square or Right Angle Screwdriver Black Electrical Tape Fuses Fuse Puller Cloth or Paper
More informationFour Panel Sequential LED Tail Light Kit Installation Guide
1969 CHEVY CAMARO Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses,
More informationCHEVY CAMARO Four panel Sequential LED Taillight kit installation guide
1978-81 CHEVY CAMARO Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED harnesses, 48 4 LED
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationCHEVY NOVA w/reverse Four Panel Sequential LED Taillight Kit Installation Guide
1970-72 CHEVY NOVA w/reverse Four Panel Sequential LED Taillight Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 (5 pin) 1 passenger
More informationInstallation Instructions
patent pending Portable Proportional Braking System Installation Instructions Part number 9400 Towing and Suspension Solutions ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 800-669-9690 Fax 360-735-9300
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationLGT-312L E-Z-Go TXT Light Bar Bumper Kit Installation Instructions
LGT-312L E-Z-Go TXT 2014+ Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationGateway 505/605 Symptom Flow Chart Lift Interlock
An ISO 9001:2008 Registered Company Gateway 505/605 Symptom Flow Chart Lift Interlock Begin diagnosis by performing the system post installation instructions notating system operation while doing checks.
More informationPN R CHEVY CAMARO w/reverse Two panel Sequential LED Taillight kit installation guide. Kit Contents:
Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2 LED extension
More informationPlus SABRE LIGHTBARS
INSTALLATION AND INSTRUCTION MANUAL Plus SABRE LIGHTBARS Models 5364LED, 5462LED, 5464LED and 5564LED PLIT445 REV. D 2/2/18 Keep any radio frequency sensitive equipment at least 20 from the bar and power
More information2016 HONDA 1000 Pioneer PN 3102 Turn signal / horn kit rev nc
2016 Honda 1000 Pioneer STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR 2016 HONDA 1000 PIONEER IF YOUR MACHINE IS NOT THIS MODEL DO NOT PROCEED. THIS KIT DOES NOT WORK ON THE PIONEER 500 nor 700 S. Contact
More informationStay-IN-Play with Panic Stop Braking
INSTALLATION INSTRUCTIONS TOWED VEHICLE BRAKING SYSTEM Stay-IN-Play with Panic Stop Braking SMI Manufacturing, Inc. P.O. Box 14040 Evansville, IN 47728 1-800-893-3763 www.smibrake.com SIP0906 Model SIP0603
More informationATTENTION. Custom Dynamics UTV Turn Signal Kit Installation Instructions
Custom Dynamics UTV Kit Installation Instructions We thank you for purchasing the Custom Dynamics UTV LED Kit. Our products utilize the latest technology and high quality components to ensure you the most
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................................. 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION
More informationM GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET
Please contact the Ford Racing Techline for the most current instruction information @ (800) FORD-788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! OVERVIEW: The following
More informationPONTIAC FIREBIRD
1974-78 PONTIAC FIREBIRD Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 LED panel mount kits 6 rubber grommets 1 power wire 1 pigtail harness Kit 1 crimp terminal
More informationUNIVERSAL ELECTRA-STEER FOR 2 COLUMN 220w Plain w Polished w Plain w Polished
UNIVERSAL ELECTRA-STEER FOR 2 COLUMN 220w Plain 8052810 220w Polished 8052610 360w Plain 8052780 360w Polished 8052760 Full refund will NOT be granted to any kits that are damaged, scratched, or altered
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationLate Model Corvair LED Tail Light Conversion Kit
Late Model Corvair LED Tail Light Conversion Kit There are just a few things that require close attention when installing these LED tail light conversion units. Other than basic hand tools and soldering
More informationMAVERICK, PINTO. Two Panel Sequential LED Tail Light Kit Installation Guide
1970-77 MAVERICK, 71-76 PINTO Two Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side
More informationATTENTION. Custom Dynamics Smart Triple Play Installation Instructions. Package Contents: - Smart Triple Play Module (1) - Instructions
Custom Dynamics Smart Triple Play Installation Instructions We thank you for purchasing the Custom Dynamics Smart Triple Play. Our products utilize the latest technology and high quality components to
More informationWolverine Turn Signal / Horn Kit 2102
All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your
More informationSmall knife. Remove black panel shown. Save 6 retaining pins for re-install later.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver PB-3425 Parts Bag 1 Ratchet & Socket set OR Ford OEM Switch (if you 1 Adjustable
More informationOLDSMOBILE CUTLASS
1971-72 OLDSMOBILE CUTLASS Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 1 Connector/Wire Kit 1 Grommet/Boot Kit 1 Power wire 2 Pigtail Harness Kits 1 Crimp terminal
More informationOptional Wiring. This section deals with some of the optional wiring that may be needed depending on how you choose to construct your car.
CHAPTER 23 Optional Wiring This section deals with some of the optional wiring that may be needed depending on how you choose to construct your car. OEM Tail light connections to Fiero harness The following
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationInstallation Instructions. QuickSilver Shifter. Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683
Installation Instructions QuickSilver Shifter Fits: GM, Ford, Chrysler Transmissions See Application Guide for Specific Applications Part # 80683 WORK SAFELY! For maximum safety, perform this installation
More informationOwner s Manual Electronic Harness Controller P/N ASM4250
Owner s Manual Electronic Harness Controller P/N ASM4250 Thunder Heart Performance Corporation MANUAL P/N EI4250 120 Industrial Drive Revision 6/3/04 White House, TN 37188 www.thunder-heart.com TABLE
More informationTwo panel Sequential LED Taillight kit installation guide
1970 CHEVELLE Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 2 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationPowerLevel s e r i e s
Owner s Manual Hydraulic Leveling CONTENTS Introduction Operation Control Panel Automatic Leveling Manual Leveling Retracting Jacks Remote Operation Care & Maintenance Troubleshooting Error Codes 1 2 2
More informationSequential Turn Signals TCSF-03 Installation Instructions FOR ONLINE INSTRUCTIONS VISIT OUR WEBSITE AT
Sequential Turn Signals TCSF-03 Installation Instructions FOR ONLINE INSTRUCTIONS VISIT OUR WEBSITE AT WWW.FOXTHUNDERCATS.COM/ELECTRONIXX Thank you for your purchase of the TCSF-03 Sequential Turn Signal
More informationGENERAL <ELECTRICAL>
00E-1 GROUP 00E GENERAL CONTENTS HARNESS CONNECTOR INSPECTION................... 00E-2............. 00E-6................. 00E-6 TROUBLESHOOTING STEPS.......... 00E-6 INFORMATION FOR DIAGNOSIS.......
More informationLokar Cable Operated Sensor Kit Installation Instructions For Ford C4 and C6
Lokar Cable Operated Sensor Kit Installation Instructions For Ford C4 and C6 Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Lokar Cable Operated
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS [1] Description: Tow Hitch Wire Harness Kit [2] Application: Nissan Rogue Note: Tow Harness application is limited to specific vehicle option packages that include tow harness
More information2005 and 09 Mustang install instructions Sequential / Chase Unit Partial Plug-N-Play Kit Meter4it Eng. Updated: 3/28/09
Updated: 3/28/09 Verify content of kit: 1- Unit with wiring harness 1- Red power wire with 15 amp fuse 1- Color instruction 2- Velcro for mounting 1-Driver taillight harness 1- Passenger taillight harness
More informationInstallation Manual: Honda CRV Power Lift Gate System
Installation Manual: Honda CRV Power Lift Gate System Page 1 of 18 NOTE: Installation Precaution 1. It is recommended to have this product installed by a professional to avoid damage caused by improper
More informationMaintenance notice proceeding
Maintenance notice proceeding When check, remove and replace car body electric relating parts, please pay attention to the proceedings below. 1. Lighting There is sealed gas in halogen bulb, so please
More informationROADMASTER, Inc NE 127th Ave. Vancouver, WA Fax roadmasterinc.com ROADMASTER, Inc.
ROADMASTER, Inc. 6110 NE 127th Ave. Vancouver, WA 98682 800-669-9690 Fax 360-735-9300 roadmasterinc.com 2008-2017 ROADMASTER, Inc. All rights reserved. 853600-05 11/17 Read all instructions before installing
More informationMercedes W123 Turn Signal Bulb, Front
Mercedes W123 Turn Signal Bulb, Front Replacement No one likes to make enemies, but driving without signaling is a quick way to do that. How frustrating is it to try to signal only to fail to due to a
More informationPN PONTIAC FIREBIRD. Kit Contents: Four Panel Sequential LED Tail Light Kit Installation Guide
1969 PONTIAC FIREBIRD Four Panel Sequential LED Tail Light Kit Installation Guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire 2 pigtail harness kits 2 crimp terminal kits PN 1100569 1969
More informationDESCRIPTION & OPERATION
DESCRIPTION & OPERATION 1991-92 ACCESSORIES & EQUIPMENT Anti-Theft System - Cherokee Passive anti-theft system is designed to prevent vehicle theft. The Security Alarm Module (SAM) is a logic controlled
More informationDIAGNOSTIC TROUBLESHOOTING INDEX
DIAGNOSTIC TROUBLESHOOTING INDEX Curtis Industries, LLC. 111 Higgins Street Worcester, MA 01606 Telephone: (508) 853-2200 Fax: (800) 876-9104 www.snoproplows.com TROUBLESHOOTING INDEX - BY PROBLEM Section
More informationInstallation Guide and User s Manual
Installation Guide and User s Manual Version 1 Table of Contents 1. Introduction...1 1.1 Notes and warnings...1 2. Installation/Setup...2 2.1 LCD monitor...2 2.2 Monitor inputs...2 3. Monitor wiring harness...3
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More information#1 PROVIDER OF HID KITS.
Please read the reference handbook carefully before removing original car lighting from the vehicle. Please read through the entire handbook carefully before installing the HID system. Following this guide
More informationTOYOTA YARIS KEYLESS ENTRY SYSTEM
TOYOTA YARIS 2011 - KEYLESS ENTRY SYSTEM Part Number: 00016-32901 Accessory Code: KE1 Conflicts Not for installation in vehicles equipped with factory installed keyless entry. Kit Contents Item # Quantity
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Model: 8510 & 8510TK Ford E Series Van 1994 2002 with stock power mirrors Tools required for the installation are: 7/16 socket, T20 screwdriver or 8mm socket, screwdriver, phillips
More informationGIVE ME A BRAKE Light Kit 2005 / 2006 MINI Cooper/Cooper S Brake Light Modification
Page 1 of 6 GIVE ME A BRAKE Light Kit 2005 / 2006 MINI Cooper/Cooper S Brake Light Modification ****Pages 1 and 2 apply only to non-convertible MINI s**** ****for convertibles please go to page 5**** This
More informationILISC515-A Shift Interlock (Manual Lift Door) Ford Transit
An ISO 9001:2008 Registered Company ILISC515-A Shift Interlock (Manual Lift Door) 2015-2018 Ford Transit Introduction The ILISC515-A is a microprocessor driven system for controlling wheelchair lift operation.
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationLokar Cable Operated Sensor Kit Installation Instructions
Lokar Cable Operated Sensor Kit Installation Instructions For GM TH350, TH400, TH200, 200-4R, 700-R4, 4L60 (and 4L60E, 4L80E with Long Selector Shaft) Building American Quality With A Lifetime Warranty!
More informationPN CHEVY TRI-FIVE. Kit Contents: Four panel Sequential LED Taillight kit installation guide
Four panel Sequential LED Taillight kit installation guide Kit Contents: 2 tail light LED panels 2 tail light turn signal LED panels 1 rubber boot/sleeve kit 1 power wire with t-tap 1 driver side LED harness,
More informationBUICK SKYLARK/GS
Sequential LED Tail Light Kit Installation Guide 1970-72 BUICK SKYLARK/GS PN 1101170 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed GM product Note The LED boards are
More informationInstallation Instructions
Installation Instructions These instructions cover the following kits: 64-66 Mustang Sequential Turn Signal LED kit 67-68 Mustang Sequential Turn Signal LED kit Kit Contents 2 x LED Tail Light Panels 2
More informationU L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M
S m a r t e r Q u i e t e r M o r e A c c u r a t e U L T I M A T E R A D A R / L A S E R D E F E N S E S Y S T E M Installation Manual PASSPORT 9500ci Comes Complete Front Radar Receiver Miniature weatherproof
More informationPN DODGE CORONET Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR BLACK. THANK YOU FOR CHOOSING KϋRYAKYN!
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE, USE,
More informationS1 Sequential. T56 Magnum. Sequential shifter. Contents and assembly instructions
S1 Sequential Sequential shifter T56 Magnum Contents and assembly instructions Parts List Sequential shifter x1 Base plate x1 Base spacer x1 Drill Square x1 Shaft fitting x1 Square washer x1 8mm Aluminium
More informationBOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications
An ISO 9001:2008 Registered Company BOM507-BC Black Out Module 2017 Ford F250-F550 Contact InterMotive for additional applications Introduction The BOM507-BC module has the ability to eliminate all exterior
More informationFord Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List:
2013-2014 Ford Mustang GT-Style Fog Light Kit Parts List: Quantity: Tool List: Fog light (Left& Right) 2 Flat head & Phillips screwdriver Upper grille with surround 1 Ratchet & Socket set OR Lower grille
More informationKATDASH Slash 6. This unit will fit all /6 instrument pods and 1977 /7s with an AMBER turn signal at the bottom center of the dash board.
KATDASH Slash 6 This unit will fit all /6 instrument pods and 1977 /7s with an AMBER turn signal at the bottom center of the dash board. To install the unit, you simply remove your original bulb carrier
More informationNissan Rogue. Installation Manual: Nissan Rogue. Power Lift Gate System. NOTE: Not for Rogue Sport Models. Page 1 of 13
Nissan Rogue Installation Manual: Nissan Rogue Power Lift Gate System NOTE: Not for Rogue Sport Models Page 1 of 13 NOTE: Installation Precaution 1. It is recommended to have this product installed by
More information* * APPLICABLE MODELS: 2016 > CX-3
PART NUMBER: 0000 8C S01(DIO) / 0000 89 S07(PIO) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0688-000* APPLICABLE MODELS: 2016 > CX-3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart
More informationMODEL DL35-CV LED REAR DECK LIGHT
TM MODEL DL35-CV LED REAR DECK LIGHT PLITSTR374 REV. A 8/4/06 Please Note: These instructions are provided as a general guideline only. Specific mounting, wiring, and/or weather-sealing may be necessary
More information4. Remove (4) 10mm and (1) 7mm bolt that holds fascia at front corners, on each side
2010 Camaro LS3 1. Disconnect battery ground 2. Remove front wheels 3. Remove (5) push pins and (5) #20 torx screws on inner front wheel well liners and remove liners on each side 4. Remove (4) 10mm and
More informationSequential LED Tail Light Kit Installation Guide PN
Sequential LED Tail Light Kit Installation Guide 1969 DODGE DART PN 1200469 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed MOPAR product Note The LED boards are shipped
More information1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide
1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED
More informationPN EL CAMINO w/reverse Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1978-81 EL CAMINO w/reverse Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness, 48 2
More informationINSTALLATION. Note: Not all of the included parts will be used during this installation. -cont.-
Driving Lights for Road Glide 5007 Fits: 98-up Road Glide PartS Included 1 Right Light Assembly 1 Left Light Assembly 1 Right Mounting Bracket 1 Left Mounting Bracket 1 Hardware Kit Including: 2 Narrow
More informationINSTALLATION. DRIVING LIGHTS for FLHT/FLHX/FLHR 5005
DRIVING LIGHTS for FLHT/FLHX/FLHR 5005 PARTS INCLUDED 1 Right Driving Light Assembly 1 Left Driving Light Assembly 1 Right Driving Light Bracket 1 Left Driving Light Bracket 4 Driving Light Bracket Plugs
More informationB U I C K G R A N D N A T I O N A L S E Q U E N T I A L L E D T A I L L I G H T K I T P N INSTALLATION GUIDE
B U I C G R A N D N A T I O N A L S E Q U E N T I A L L E D T A I L L I G T I T P N 1 1 0 0 8 8 6 INSTALLATION GUIDE Please refer to Invoice for full warranty information. Digi-Tails is not a licensed
More informationINSTALLATION INSTRUCTIONS For 2007 and newer Jeep Wrangler JK
7 LED sealed beam headlamp with switchback Halos and DRL INSTALLATION INSTRUCTIONS For 2007 and newer Jeep Wrangler JK SB7250XX-BLK, SB7250XX-CHR, SB7050BA-BLK, SB7060XX-BLK, SB7060XX-CHR, SB7160XX-CHR,
More informationReplacing gauge lamps with LED's
Replacing gauge lamps with LED's To pull the gauges just to replace a small bulb is quite a nuisance and the existing bulbs are not all that bright and easily blow. It is thus worthwhile replacing them
More informationINSTALLATION MANUAL SPECTRUM BRAKE CONTROL
INSTALLATION MANUAL 51170 SPECTRUM BRAKE CONTROL TABLE OF CONTENTS Controls & Components Tools List Before You Begin Wiring Wiring Diagram Mounting the LED Display Rotary Knob Wiring the Plug Connector
More informationIMPORTANT! Remote Control Instructions
Remote Control Instructions FOR New Tarp Remote Control Installation Use these in place of the rocker switch and solenoid section of instructions in your roll tarp owner s manual. FOR Existing Electric
More informationTOYOTA SCION XB 2005 LSD INSTALLATION
TOYOTA SCION XB 2005 LSD INSTALLATION 50056005 TOYOTA SCION XB 07/07 1 Date 07/24/2007 50056005 TOYOTA SCION XB 07/07 2 INSTALLATION INTRODUCTION 1. REMOVING THE FENDER AND DOORS FROM THE A-PILLAR AND
More information1968 PLYMOUTH ROAD RUNNER
Sequential LED Tail Light Kit Installation Guide 1968 PLYMOUTH ROAD RUNNER PN 1200568 Please refer to Invoice for full warranty information DIGI-TAILS is not a licensed MOPAR product Note The LED boards
More informationAdjustable Light Kits E-Z-Go TXT All Models Installation Instructions
Adjustable Light Kits E-Z-Go TXT All Models 1996-2013 Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and negative
More informationM14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS
M14 AUTOMOTIVE SPARK PLUGS AND WIRES CONVERSION KIT INSTALLATION INSTRUCTIONS (It is highly recommended you read the instructions completely before beginning) 1. Be sure the magneto switches are turned
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Tow Hitch Wire Harness Kit Quest (2011) 999T8 NW000 Installation of this accessory requires installation of
More informationBody Electrical System
Body Electrical System GENERAL....BE -2 MULTI FUNCTION SWITCH...BE -8 HORN...BE -11 FUSES AND RELAYS...BE -12 INDICATORS AND GAUGES...BE -19 LIGHTING SYSTEM...BE -24 DAYTIME RUNNING LIGHTS...BE -30 BE-2
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Handle Camera Mirror Display 2004-2014 Ford F-150 and 2008-2015 Ford Super Duty (Kit part numbers 9002-9521) Kit Contents: Mirror Tailgate Handle with camera and harness Interior
More information