CXDH3 / CDH3 - Features

Transcription

1 CXDH / CDH - Features CXDH - roportional compensated bankable valves CDH - ON/OFF compensated bankable valves ankable proportional directional valves with signal locally compensated. CXDH/CDH series valves are used for controlling fluid direction and flow rate Load sensing system allow high efficiency and low energy consumption. Flow regulation is load indipendent. Electrical roportional or On/Off control Open center inlet module for fixed displacement pumps Closed center inlet module for variable displacement Load Sensing pumps Assemblable with Aron s bankable valves CD, CDC, CX Assemblable with revini Hydraulics HV valves (intermediate element required). Community design & Italian patent pending Introduction Hydraulic scheme CXDH: he flow rate controlled by the valve is a function of the supply current to the proportional control solenoid. CDH: he flow rate controlled by the valve is predefined by a calibrated hole screwed into the port A and/or. Flow regulation is load independent and is not affected by other operated function when pump has sufficient capacity. Load compensantion is achieved by a 2 way pressure compensator wich holds the pressure drop constant across the proportional spool. A A CXDH. proportional CDH. on/off Operating specifications Max. operating pressure ports /A/ 00 bar Max. operating pressure ports (Dynamic pressure allowed for 2 millions of cycles) 20 bar Max inlet flow 80 l/min (see characteristic curves) Regulated flow rate (A / ports) up to a l/min Relative duty cycle Continuous ype of protection (Hirschmann coil) I 6 Fluid viscosity mm²/s (46 cst recommended) Fluid temperature -20 C 7 C Ambient temperature -20 C 60 C ISO 4406:1999: class 19/17/14 roportional valves NAS 168: class 8 Max. contamination level with filter ß10 7 ISO 4406:1999: class 21/19/16 ON/OFF valves NAS 168: class 10 with filter ß2 7 Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified ARON electronic control units. IE/CXDH-CDH-INRO/001/2011 6

2 CXDH / CDH - Features ressure drop - FEH0.Q - Open center inlet module for fixed displacement pumps ( connected on inlet module). Inlet module ressure Drops* 0 2 Dp (bar) Q (l/min) * ressure drop can be reduced with special spring in the inlet module, when using differential pressure 4 bar in the compensated valves. I-Q curves CXDH (Curves acquired with REM card, opening stroke) 40 Differential ressure = 8 bar spool 0 Differential ressure = 4 bar spool Q (l/min) Q (l/min) D D I(%) I(%) Compensation curves - CXDH (curves acquired with FEH0.Q inlet module) 40 Differential ressure = 8 bar spool 0 Differential ressure = 4 bar spool Q (l/min) Q (l/min) D D (bar) (bar) o obtain a correct compensation the inlet flow must be 8% greater the sum of the regulated flow. he fluid used is a mineral based oil with a viscosity of 46 mm²/s at 40 C. he tests have been carried out at with a fluid of a 40 C. IE/CXDH-CDH-INRO/001/2011 7

3 9 CXDH / CDH - Features Overall dimensions and hydraulic circuits CXDH proportional valves with FEH0Q inlet module for Fixed Displacement pump 9 A 2 x M6-6H 12 2 x M6-6H fixing holes tighten the screws to a torque of 10 nm No elements A mm mm C mm D mm fixing feet available on request 1 G A A C D 9 A CXDH proportional valves with FEH0 inlet module for Variable Displacement Load Sensig pump 2 x M6-6H 12 2 x M6-6H fixing holes tighten the screws to a torque of 10 nm No elements A mm mm C mm D mm fixing feet available on request A A 7 A 2 A 10 C IE/CXDH-CDH-INRO/001/2011 8

4 CXDH / CDH - Features Composition Form CXDH valves can be assembled with CDH valves, and all the bankable line CDC, CD, CX (see page 2) Ref. ipo Description age 1 FEH0Q OEN CENER inlet module for fixed displacement pumps 40 FEH0 CLOSED CENER inlet module for variable displacement load sensing pumps 42 2 CXDH ROORIONAL compensated valves 44 CDH ON/OFF compensated valves 47 4 FUH Outlet module units 1 HSIF Interface with revini Hydraulics HV41 module 2 6 Mounting kit 7 Fixing feet 8 Connectors 4 9 s o obtain the best performances, we suggest to assemble the working sections with higher flow rate near the inlet module, leaving the ones with lower flow at the end of the assembled valve. How to order o order the assembly, specify the codes in progressive order (inlet, valves, outlet, mounting kit, feet). See example page 60. For any further special version not shown in this catalogue, please contact our echnical Departement. IE/CXDH-CDH-INRO/001/2011 9

5 FEH0Q OEN CENER INLE MODULE FOR FIXED DISLACEMEN UMS Open center inlet module units for fixed displacement pumps with pressure relief valve and electrical venting valve Module units FEH0.Q provide a pressure compensator for fixed displacement pump, a pressure relief valve with adjustable pressure setting ranges CM-MC/MS and an electrical venting valve CR04. It includes a pressure compensated load sensing signal bleed to minimize system losses even at high operating pressures. Signal bleed can be closed in case it not required. Cast iron zinc plated body. HYDRAULIC SYMOL 1 G Connector to be ordered separately, see page 4. ORDERING CODE FEH0 Q C * * ** 1 Inlet module units with pressure relief valve Electrical venting valve ressure compensator element Size orts G1/2 Adjustment: C = Grub screw Setting ranges: 1 = 90 bar 2 = bar = >10 bar Voltage venting valve (1): L = 12 Vdc M = 24 Vdc N = 48 Vdc 0 = Without electrical venting valve (plugged) Variants (1-2): S1 = No variants SV = Viton Y = ush button emergency () S = Rotary emergency () AJ = AM Junior connection 22W (see page ) CX = Deutsch connect. bidirectional diode (see page ) Serial No. FEAURES [bar] Max. operating pressure 00 bar Setting ranges for pressure relief valve Spring 1: 90 bar Spring 2: bar Spring : >10 bar Max. flow 80 l/min (see charateristic curves) Fluid viscosity mm²/s Max bleed flow 0. l/min Fluid temperature -2 C 7 C Ambient temperature -2 C 60 C Max. contamination level (filter ß2 7) Weight Max. excitation frequency Duty cycle ype of protection (in relation to the connection used) ISO 4406:1999: class 21/19/16 NAS 168: class kg 2 Hz I6 o obtain a correct compensation the inlet flow must be 8% greater the sum of the regulated flows CHARACERISIC CURVE Inlet module ressure Drops (1) s technical data, see page ) Voltage codes are not stamped on the plate, their are readable on the coils (2) Connector to be ordered separately, see page 4; Other variants available on request. () Emergency (see page Q [l/min] IE/FEH0Q001/001/

6 FEH0Q OVERALL DIMENSIONS 8 4 (8) 2 x M6-6H (8.2) G1/2" 4 x M6-6H Ø (10.) (70) (1) 9 70 holes for optional fixing feets predisposition to plug load sensing bleed G standard emergency 60 2 x O-RING Sh 1 x O-RING Sh 1 VARIANS S Emergency rotary Y Emergency with push button AJ AM Junior CX Deutsch with diode, Corsa (Stroke) 8 max Ø20 Ø10 29, IE/FEH0Q001/001/

7 FEH0 CLOSED CENER INLE MODULE FOR VARIALE DISLACEMEN LOAD SENSING UMS Closed center inlet module units for variable displacement Load Sensing pumps with pressure relief valve Module units FEH0. for variable displacement Load Sensing pump provide a pressure relief valve CM0 with adjustable pressure setting ranges and a pressure compensated load sensing signal bleed to minimize system losses even at high operating pressures. Signal bleed can be closed in case it is not required. Cast iron zinc plated body. HYDRAULIC SYMOL ORDERING CODE FEH0 * * ** 1 Inlet module units with pressure relief valve With signal Size orts G1/2 Adjustment: M = lastic knob C = Grub screw Setting ranges: 1 = max 0 bar 2 = max 140 bar = max 0 bar Variants: 00 = No variants V1 = Viton Serial No. FEAURES Max. operating pressure 00 bar Setting ranges for pressure relief valve Spring 1: max 0 bar Spring 2: max 140 bar Spring : max 0 bar Max. Flow 80 l/min (see charateristic curves) Fluid viscosity mm²/s Fluid temperature -2 7 C Ambient temperature -2 C 60 C Max. contamination level (filter ß2 7) Weight RESSURE RELIEF VALVE CURVES ISO 4406:1999: class 21/19/16 NAS 168: class kg [bar] ressure Flow Q [l/min] 2 1 [bar] Minimun setting pressure Q [l/min] IE/FEH0001/001/

8 FEH0 OVERALL DIMENSIONS N 2 M6 12. Ø1 2.8 G1/2" G1/2" N 4 M Ø C = Adjustment with grub screw M = Adjustment with plastic knob holes for optional fixing feets 2 x O-RING Sh 1 x O-RING Sh G1/4" IE/FEH0001/001/2011 4

9 CXDH ROORIONAL COMENSAED VALVES Stackable proportional directional valves with signal locally compensated CXDH..A../CXDH..C.. series valves are used for controlling fluid direction and flow rate as a function of the supply current to the proportional control solenoid. Flow regulation is load indipendent. Load compensantionis achieved by a 2 way pressure compensator wich holds, the pressure drop constants across the proportional spool. Cast iron zinc plated body. Community design patent pending HYDRAULIC SYMOL A A A A ORDERING CODE CXDH * * ** N * * * ** 1 roportional compensated bankable valve Size A = Single solenoid C = Double solenoid ody type: A = orts G/8 parallel G= Interface for modular valves ype of spool (1) 0 = Symmetrical flow path control Flow rating * p 8bar p 4bar D 8 l/min l/min 2 16 l/min 12 l/min 22 l/min 18 l/min 4 l/min 28 l/min Differential pressure Dp 8 = Dp 8 bar 4 = Dp 4 bar Max. current at solenoid (2): E = 2. A (9 Vdc) - Special coil F = 1.76 A (12 Vdc) G = 0.88 A (24 Vdc) Variants (): S1 = No variant LF = Emergency control lever (see page 0) For body type G order LR variant (emergency lever 180 rotated) SV = Viton ES = Emergency button (4) 2= Rotary emergency (4) R = Rotary emergency 180 (4) AJ = AM Junior coil (see page 9) CZ = Deutsch D04-2 coil (see page 9) Serial No. (1) Available spool 01 A and ports are not sealed: fluid can escape from line (see hydraulic scheme). (2) s technical data, see page 9 Voltage codes are not stamped on the plate, their are readable on the coils () Connector to be ordered separately, see page 4; Other variants available on request. (4) Emergency see page0 CXDH..A.A.0.. CXDH..A.G.0.. * CXDH..C.A.0.. CXDH..C.G.0...* * hanks to the design of the modular body (type G), an anti-shock modular valve can works same with CXDH valve energized or de-energized (see hydraulic symbol) FEAURES Max. operating pressure 00 bar Max. operating pressure ports (ressure dynamic allowed for 2 millions of cycles) 20 bar Regulated flow rate (A / ports) up to l/min Relative duty cycle Continuous ype of protection (Hirschmann coil) I 6 Fluid viscosity mm²/s Fluid temperature -20 C 7 C Ambient temperature -20 C 60 C Max. contamination level (filter ß10 7) ISO 4406:1999: class 19/17/14 NAS 168: class 8 Weight with single solenoid Weight with double solenoid 2.8 kg 2.77 kg 24Vdc Current supply WM (pulse width modulation) Max. current solenoid 2. A 1.76 A 0.88 A Solenoid coil resistance at 2 C (77 F) 2.2 Ohm 4.0 Ohm 16.0 Ohm WM or superimposed dither frequency 10 Hz Response time 0 100% 100% 0 2 ms ms 40 ms ms 8 ms ms Frequency response -db (input signal 0% ±2% Vmax) 22 Hz 22 Hz 12 Hz Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified ARON electronic control units. erformance data carried out using the specified Aron power amplifier SE..AN... serie 1 - EUROCARD format (input voltage = 24V). Accessories REM.S.RA.*.*. REM.D.RA.*.*. Card type control for single and double solenoid CE.S... Electronic amplifier plug version for signle solenoid MAV Electronic module for integrate control of proportional valves and ON/OFF JMEI0M Joystick with standard handle JMIU0M70018 Joystick erson present handle Modular valves CM (page 1) and CMM (page ) IE/CXDH001/001/

10 CXDH CXDH... - CHARACERISIC CURVES I-Q curves - (Curves acquired with REM card, opening stroke) Compensation curves (curves acquired with FEH0.Q inlet module) Differential ressure p = 8 bar Differential ressure p = 4 bar Differential ressure p = 8 bar Differential ressure p = 4 bar Q [l/min] D Q [l/min] D Q [l/min] D Q [l/min] D I [%] I[%] p [bar] p [bar] he fluid used is a mineral based oil with a viscosity of 46 mm²/s at 40 C. he tests have been carried out at with a fluid of a 40 C. OVERALL DIMENSIONS ody type A orts G/8 arallel O-RING 2018/ Sh O-RING 207/2-012 N2 90Sh FORI Ø 6. 4 HOLES = 69. = 229. = = G/8" (*) 0. s can be rotated by 180 Fittings, max. tightening torque 60 Nm IE/CXDH001/001/2011 4

11 CXDH CXDH... - OVERALL DIMENSIONS ody type G Interface for modular valves O-RING 2018/ Sh 4 x O-RING 207/2-012 N2 90Sh HOLES Ø x Ø x M 1 O-RING 207/2-012 N2 90Sh IE/CXDH001/001/

12 CDH ON/OFF COMENSAED VALVES ON/OFF Compensated Valves Stackable ON/OFF directional valves with signal locally compensated. CDH..*.E series valves are used for controlling fluid direction and flow rate. he flow rate controlled by the valve is predefined by a holed calibrated washer screwed into the port A and/or. Flow regulation is load independent. Load compensantion is achieved by a 2 way pressure compensator wich holds, the pressure drop constants across the proportional spool. Cast iron zinc plated body. Connector to be ordered separately, see page 4. ORDERING CODE HYDRAULIC SYMOL CDH On/Off compensated bankable valve A * Size ody type: A = orts G/8 parallel Ø... Ø... E Electrical operator ** Spool (see table 1) * ** ** * * ** 1 Mounting (see table 2) Holed washer on port A (see table ) Holed washer on port (see table ) Omit if equal to screw on port A Differential pressure Dp 8 = Dp 8 bar 4 = Dp 4 bar Voltage (see table 4) Variants (see table ) Serial No. FEAURES Max. operating pressure ports /A/ 00 bar Max. operating pressure ports (ressure dynamic allowed for 2 millions of cycles) 20 bar Max flow See table Max excitation frequency Hz Duty cycle ype of protection (Hirschmann coil) I 6 Fluid viscosity mm²/s Fluid temperature -2 C 7 C Ambient temperature -2 C 60 C Max. contamination level (filter ß2 7) ISO 4406:1999: class 21/19/16 NAS 168: class 10 Weight with single solenoid Weight with double solenoid 2.8 kg 2.77 kg General flow tolerance ±10% Operating specifications are valid for fluid with 46 mm²/s viscosity at 40 C, using the specified ARON electronic control units. IE/CDH001/001/

13 CDH ORDERING CODE ab.1 - Spool wo solenoids, spring centred C Mounting Code A a A O b Covering ransient position 01 a b + (2) 02 a b 0 a b 04 (1) a b (2) One solenoid, side A E Mounting A Code a A O Covering ransient position 01 a + (2) ab. - Holed washer on port A / Code Flow (l/min) Dp = 8 bar Dp = 4 bar no screw Other flow rates available on request A Interchangeable screw into fittings ports 02 a 0 a 04 (1) a 1 a 16 a (2) One solenoid, side F Mounting A Code O b Covering ransient position 01 b 02 b 0 b 04 (1) b 1 b 16 b (2) (2) ab.4 - s D1 voltage (7) Max. winding temperature Code Voltage (Ambient temperature 2 C) Rated power W 20 C (Ohm) ±10% L 12 Vdc 110 C M 24 Vdc 110 C V () 28 Vdc 110 C N () 48 Vdc 110 C Z (4) 102 Vdc 110 C 0 40 () 110 Vdc 110 C 0 87 X () 20 Vdc 110 C 0 17 W (6) Without coils ab. - Variants (7-8) Code Variant S1 No variant SV Viton LF Emergency control lever (see page 0) LR Emergency control lever180 rotated (vedi pagina 0) ES Emergency button (vedi pagina 0) 2 (9) Rotary emergency button (vedi pagina 0) R (9) Rotary emergency b. 180 (vedi pagina 0) AJ (10) AM Junior connection (vedi pagina 7) AD (10) AM Junior and integr diode (vedi pagina 7) SL (10) with flying leads 17 mm (vedi pagina 7) CZ (10) with Deutsch D04-2 (vedi pagina 8) ab.2 - Mounting Code C E F G (1) H (1) A a A O b A a A O A O b A A O b A a O Symbol (1) Specials with price increasing (2) On spool 01 and 04 A and ports are not sealed: fluid can escape from line (see hydraulic scheme). () Special voltage (4) With rectifier: 11 VAC/0Hz VAC/60Hz () With rectifier: 20 VAC/0Hz VAC/60Hz (6) erformance are guaranteed only using valves completed with F coil (7) Connector to be ordered separately, see page 4; s technical data, see page 7-8; (8) Other variants available on request. All the variants are considered without connectors. (9) ightening torque max. 6 9 Nm (CH n. 22) (10) Available in 12V or 24V DC voltage only. IE/CDH001/001/

14 CDH OVERALL DIMENSIONS O-RING 2018/ Sh O-RING 207/2-012 N2 90Sh G /4" = 229. = Fittings, max. tightening torque 60 Nm IE/CDH001/001/

15 CXDH / CDH (variants) LF AND lr variants - Emergency control lever LF VARIAN LF variant 18. he emergency control lever for solenoid valves by Aron, represents a develop in terms of safety and flexibility among applied hydraulic components. hanks to his flexibility, the component was designed to be inserted between the valve body and the spool, providing total interchangeability between the different types of solenoid body valves manufactured by Aron. he component is available for both ON/OFF directional control and proportional valves (*). As an emergency lever applied to solenoid valves, the control can be used as a safety device in conformity with the industry standards, also playing an useful role in the event of power cuts. he control can be used in agricultural and mobile fields; the manual action can be used to carry out periodic maintenance work on mobile components of the vehicle, in perfectly safe working conditions LR VARIAN 46 HYDRAULIC SYMOL Spool 01 available on request Max operating pressure port Mounting type Spools type dynamic static 160 bar 210 bar C - F - H assembly example with LF variant * Max flow of proportional valves can be reduced compared to versions without emergency control lever when electrical operated. Max flow of proportional valves lever operated is increased compared to the max flow given when valves are electrical operated. OHER VARIANS ES Manual emergency 2 Rotary emergency R Rotary emergency 180 max 66 max Ø Ø AJ AM Junior AD AM Junior + Diode CZ Deutsch D04-2 SL Flying leads RS lastic coil , Emergency 2 and, tightening torque max. 6 9 Nm (CH n. 22) IE/CXDH-CDH-VAR/001/2011 0

16 FUH OULE MODULE UNIS Outlet module units Outlet module with port G1/2 threaded. Cast iron zinc plated body. HYDRAULIC SYMOL ORDERING CODE FEAURES FUH 00 1 Outlet module unit Size ort size: = G/4 00 = No variants Serial No. Max. operating pressure Max. Flow 00 bar 80 l/min Hydraulic fluids Mineral oils DIN 124 Fluid viscosity Fluid temperature mm²/s -2 7 C Ambient temperature -2 C 60 C Max. contamination level (filter ß2 7) Weight ISO 4406:1999: class 21/19/16 NAS 168: class kg OVERALL DIMENSIONS 4 x Ø x M6-6H G/4" 2 x M6-6H IE/FUH001/001/2011 1

17 HSIF Interface with revini Hydraulics HV41 module Interface between HV41 and CXDH / CDH he HSIF.. interface hydraulically connects the elements of proportional valves CXDH or ON/OFF valves CDH with the elements of proportional valve HV 41. his type of combination is highly appreciated in those cases involving great differences in flow between the controlled actuators. he HSIF module must be inserted into the proportional valve configuration between the last HV41 working section and the first CXDH/CDH working section. Up to eight elements of the HV41 and eight elements of the CXDH or CDH can be installed. he HSIF interface replace the inlet module for CXDH/CDH. Cast iron zinc plated body. HYDRAULIC SYMOL Lato/Side CXDH ORDERING CODE HSIF00 Interface 1 Lato/Side HV HV ype (HV 41) Identifying code FEAURES Max. operating pressure Max. Flow Fluid viscosity Fluid temperature 00 bar 80 l/min mm²/s -2 7 C Ambient temperature -2 C 60 C Max. contamination level (filter ß2 7) Weight ISO 4406:1999: class 21/19/16 NAS 168: class 10.8 kg OVERALL DIMENSIONS n. 2 M8-6H 1 O-Ring 2018/ Sh O-Ring 207/2-012 N2 90Sh O-Ring 207/2-012 N2 90Sh n. 4 M8-6H cavity for csrv or hesc. please see brevini hydraulics catalogue IE/HSIF00/001/2011 2

18 Mounting kit Kit composed by No. 4 rods and No. 8 stud nuts Nuts tightening torque: 10Nm Elements CDC CD CX Intlet module FE / FE02 FE10 FE10 Code Length Length Length Code Code (mm) (mm) (mm) No 2 V V V No V V V No 4 V V V No V V V No 6 V V V No 7 V V V No 8 V V V Outlet module FU Kit composed by No. 4 rods and No. 4 stud nuts Nuts tightening torque: 10Nm Fixing feet Elements CXDH CDH CDC (*) CD (*) CX (*) Intlet module FEH0Q / FEH0 / HSIF Length Code (mm) No 1 V No 2 V No V No 4 V No V No 6 V No 7 V No 8 V Outlet module FUH * only valves with line: CDC/CD body L-M ; CX body L 1 Ref. Code Intlet module Outlet module Descriprion 1 V FE / FE02 FE10 / FE10 FU Kit supplied with the valves, composed by: - No. 2 feet 2 Screw tightening torque: 10Nm 2 V (*) FEH0Q FEH0 FUH Kit supplied on request (**) composed by: - No. 2 feet - No. 4 screws - No. 4 washers * Fixing feet can not be used with HSIF interface module unit. ** If the kit is not required, the valve can be fixed by the fixing holes on the bottom faces of the inlet and outlet modules (see drawing on page 8) Feet mounting example Intel module FE10, outlet module FU, mounting on OOM position (standard mounting) Intel module FE10, outlet module FU, mounting on O position (to be specify) Intel module FEH0Q, outlet module FUH, mounting on OOM position (standard mounting) Intel module FEH0Q, outlet module FUH, mounting on O position (to be specify) IE/CD-CX_MOUNINGKI/001/2011

19 Connectors Connectors for control valves in accordance with DIN 460 / ISO Connector rotection level ype Cable gland Code lack color G09 V M 42 Standard I6 Grey color G09 V lack color G11 V Grey color G11 V VAC/VDC G09 V Ø 6 8 mm (G09) Ø 8 10 mm (G11) Lens cover with pilot light (*) I6 24 VAC/VDC G09 V VAC/VDC G09 V VAC/VDC G09 V Screw tightening torque: 60Ncm Connector rotection level ype Cable gland Code M 42 With rectifier (*) Inlet voltage VAC Outlet voltage 9 20 VDC I6 lack color G09 V Grey color G09 V VAC G09 V Ø 6 8 mm (G09) Lens cover with pilot light and rectifier (*) Inlet voltage VAC Outlet voltage 9 20 VDC I6 24 VAC G09 V VAC G09 V VAC G09 V VAC G09 V Screw tightening torque: 60Ncm M Connector rotection level ype Cable gland Code With protection level I67 I67 lack color V Grey color V Ø 4 7 mm Screw tightening torque: 60Ncm Electrical features of connectors Ø 6 8 mm (G09) Ø 8 10 mm (G11) I6 Seal Guarnizione Seal I67 Seal Cable gland 19 Ø 4 7 mm Cable gland Description I6 I67 AC rated voltage DC rated voltage in conctat rated flow in conctat max. flow Max. 20 V Max. 00 V 10A 16A Max. 20 V Max. 00 V 10A 16A Max. section cable 1. mm² 1. mm² Cable gland G09 - M16x1, Cable gland G11 - G 1/2 - M20x1, rotection level Insulation class Operating temperature Ø cable 6 8 mm Ø cable 8 10 mm I6 EN6029 VDE /89-40 C 90 C Ø cable 4 7 mm I67 EN6029 VDE /89-20 C 80 C he degrees of protection indicate is guaranteed only if the connectors were properly mounted with his original seals. (*) Don t use for proportional versions IE/CD-CX_CONNECORS/001/2011 4

20 s 18W COI ype of protection I 6 Number of cycle 18000/h Supply tolerance ±10% Ambient -0 C 60 C Duty cycle Insulation class wire Weight F kg Ø ISO 4400 (DIN 460) SANDARD Hirschmann ISO 4400 DIN460 Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 1 C 18 W 7.7 W M M 24 VDC 1 C 18 W 1 W M N 48 VDC 1 C 18 W 116 W M VDC 1 C 18 W 27 W M Z 102 VDC 120 C 18 W 78 W M X 20 VDC 120 C 18 W 2627 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C DEUSCH and bidirectional integrated diode (CX variant) Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 1 C 18 W 7.7 W M M 24 VDC 1 C 18 W 1 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C 22W COI ype of protection I 6 Number of cycle 18000/h Supply tolerance ±10% Ambient temperature -0 C 60 C Duty cycle Insulation class wire Weight H 0.2 kg AM Junior (AJ variant) Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 1 C 22 W 6. W M M 24 VDC 1 C 22 W 2.6 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C IE/CD-CX_COI/001/2011

21 Ø14.1 min ISO 4400 (DIN 460) I s 27W COI - A09 ype of protection I 6 Number of cycle 18000/h Supply tolerance ±10% Ambient temperature -0 C 60 C Duty cycle Insulation class wire Weight H 0.21 kg SANDARD Hirschmann ISO 4400 DIN460 (H connection) Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 12 C 27 W. W M M 24 VDC 12 C 27 W 21. W M N 48 VDC 12 C 27 W 8. W M Z 102 VDC 12 C 27 W 92 W M VDC 12 C 27 W 448 W M X 20 VDC 12 C 27 W 177 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C = 20 = 10 F WIRES and integrated bidirectional DIODE (F/I connection - FL/LD variant) obina Wires Max winding Rated Resistance Spare Codice ensione (mm) temperature (1) power ±7% (2) code L 12 VDC F = C 27 W. W M M 24 VDC F = C 27 W 21. W M L 12 VDC I = C 27 W. W M M 24 VDC I = C 27 W 21. W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C AM Junior (A connection - AJ variant) Code Max winding temperature (1) Rated power Resistance ±7% (2) Spare code Voltage L 12 VDC 12 C 27 W. W M M 24 VDC 12 C 27 W 21. W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C DEUSCH + bidirectional DIODE - D04-2 (D connection - CX variant) Code Max winding temperature (1) Rated power Resistance ±7% (2) Spare code Voltage L 12 VDC 12 C 27 W. W M M 24 VDC 12 C 27 W 21. W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C IE/CD-CX_COI/001/2011 6

22 s 0 W COI - D1 ype of protection I 66 Number of cycle 18000/h Supply tolerance ±10% Ambient temperature -0 C 60 C Duty cycle Insulation class wire Weight H 0.4 kg SANDARD Hirschmann ISO 4400 DIN Ø 4 4 *** VDC Ø 2 Ø Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M V 28 VDC 110 C 0 W 2.6 W M N 48 VDC 110 C 0 W 7.2 W M Z 102 VDC 110 C 0 W 40 W M VDC 110 C 0 W 87 W M X 20 VDC 110 C 0 W 178 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C Ø 4 4 *** VDC Ø 2 Ø WIRES 17 mm (SL variant) Code Max winding temperature (1) Rated power Resistance ±7% (2) Spare code Voltage L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C Ø 4 4 *** VDC Ø 2 Ø AM Junior (AJ variant) Code Max winding temperature (1) Rated power Resistance ±7% (2) Spare code Voltage L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C *** VDC AM Junior + idirectional DIODE (AD variant) Ø 4 4 Ø 2 Ø Code Max winding temperature (1) Rated power Resistance ±7% (2) Spare code Voltage L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C IE/CD-CX_COI/001/2011 7

23 s 0 W COI - D1 ype of protection I 66 Number of cycle 18000/h Supply tolerance ±10% Ambient temperature -0 C 60 C Duty cycle Insulation class wire Weight H 0.4 kg Ø 4 4 *** VDC Ø 2 Ø DEUSCH D04-2 (CZ variant) Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C LASIC body (RS variant) () Ø Ø 27 Max winding Rated Resistance Spare Code Voltage temperature (1) power ±7% (2) code L 12 VDC 110 C 0 W 4.8 W M M 24 VDC 110 C 0 W 18.8 W M V 28 VDC 110 C 0 W 2.6 W M VDC 110 C 0 W 87 W M (1) Ambient temperature 2 C - (2) Ambient temperature 20 C IE/CD-CX_COI/001/2011 8

24 s D1 COI - (for proportional valves) ype of protection I 66 Number of cycle 18000/h Supply tolerance ±10% Ambient temperature -0 C 60 C Duty cycle Insulation class wire Weight H 0.4 kg Ø 4 4 *** VDC Ø 2 Ø SANDARD Hirschmann ISO 4400 DIN460 Max winding Resistance Current Code Voltage temperature (1) ±7% (2) E 9 VDC 12 C 2. A 2.2 W F 12 VDC 12 C 1.76 A 4 W G 24 VDC 12 C 0.88 A 16 W (1) Ambient temperature 2 C - (2) Ambient temperature 20 C Ø 4 4 *** VDC Ø 2 Ø AM Junior (AJ variant) Max winding Resistance Current Code Voltage temperature (1) ±7% (2) E 9 VDC 12 C 2. A 2.2 W F 12 VDC 12 C 1.76 A 4 W G 24 VDC 12 C 0.88 A 16 W (1) Ambient temperature 2 C - (2) Ambient temperature 20 C Ø 4 4 *** VDC Ø 2 Ø DEUSCH D04-2 (CZ variant) Max winding Resistance Current Code Voltage temperature (1) ±7% (2) E 9 VDC 12 C 2. A 2.2 W F 12 VDC 12 C 1.76 A 4 W G 24 VDC 12 C 0.88 A 16 W (1) Ambient temperature 2 C - (2) Ambient temperature 20 C IE/CD-CX_COI/001/2011 9

25 How to order EXAMLE WIH NO COMENSAED VALVES FE101C002 - CXQCIDFS12-4 x CDCAE0C12 - FU V * Inlet module unit with pressure relief valve Size ort G/8 Adjustment pressure with grub screw Setting range: 20 bar No variant Serial No. 2 Open loop proportional compensated flow regulator Size way compensation with secondary line Flow rates 2 l/min With decompression 1.76A (12 VDC) No variant Serial No. 2 No. 4 directional control bankable valves Size arallel body ports G/8 Electrical operator Spool 0 Mounting C double solenoid 12 VDC No variant Serial No. 2 Otulet module unit Size ort size G/8 No variant Serial No. 2 Mounting kit for bankable valves and inlet module unit FE10 * It is not need to specify the fixing kit, standard supplied + connector to be ordered separately: 8 x V No. 8 black color EXAMLE WIH COMENSAED VALVES FEH0QCMS11 - CXDHCA0N48GS11-2 x CDHAE0C104MS11 - FUH001 - V V Open center inlet module for fixed displacement pumps Electrical venting valve ressure compensator element orts G1/2 Adjustment pressure with grub screw Setting range: >10 bar Voltage venting valve 24 VDC No variant Serial No. 1 roportional compensated valve Size Double solenoid arallel body ports G/8 Spool 0 Symmetrical flow path control Flow rating l/min Differential pressure 8 bar 24 VDC (0.88A) No variant Serial No. 1 No. 2 ON/OFF compensated valve Size arallel body ports G/8 Electrical operator Spool 0 Double solenoid Holed washer on port A/ 1. l/min Differential pressure 4 bar 24 VDC No variant Serial No. 1 Outlet module unit Size ort size G/4 No variant Serial No. 1 Mounting kit for bankable valves and inlet module unit FEH0Q Fixing feet kit for inlet module FEH0Q and outlet module FUH + connector to be ordered separately: 1 x V x V No. 1 grey color No. 6 black color EXAMLE WIH COMENSAED AND NO COMENSAED VALVES FEH0C x CXDHCA0N4GS11-2 x CDLE0CMS12 - FUH001 - V V Closed center inlet module for variable displacement load sensing pumps signal Size orts G1/2 Adjustment pressure with grub screw Setting range: 140 bar No variant Serial No. 1 No. 2 proportional compensated valves Size Double solenoid arallel body ports G/8 Spool 0 Symmetrical flow path control Flow rating 18 l/min Differential pressure 4 bar 0.88A (24 VDC) No variant Serial No. 1 N. 2 directional control valves Size arallel body ports G/8 version Electrical operator Spool 0 mounting C Double solenoid 24 VDC No variant Serial No. 2 Outlet module unit Size ort size G/4 No variant Serial No. 1 Mounting kit for 4 bankable valves and inlet module unit FEH0 Fixing feet kit for inlet module FEH0 and outlet module FUH + connector to be ordered separately: 4 x V x V No. 4 grey color No. 4 black color IE/CD-CX_ ORDER/001/

26 Electromagnetic compatibility ELECROMAGNEIC COMAIILIY EMC (2004/108 EC) he RODUCS NO CONAINING ELECRONIC OARDS INSIDE for the actuation of the hydraulic control (as a pure example our AD, AD, modules MHF - MHOF) are defined passive from the electrical point of view, as driven by an external power/command unit. hese products therefore don t fall directly within the field of application of the aforementioned directive and therefore are not subject to the relevant certification and CE marking by revini Fluid ower S.p.a. It will be instead the external power/command unit, chosen by the Customer according to his needs and not included in the hydraulic system supplied by revini Fluid ower S.p.a., who must be certified according with the directive and depending on the environment where it will be used (industrial, mobile, home). IE/CD-CX_ EMC/001/