CITY OF LANCASTER SANITATION DEPARTMENT 2016 REAR LOAD PACKER TRUCK BID PACKET

Size: px

Start display at page:

Download "CITY OF LANCASTER SANITATION DEPARTMENT 2016 REAR LOAD PACKER TRUCK BID PACKET"

Nathaniel Lawrence
5 years ago
Views:

1 CITY OF LANCASTER SANITATION DEPARTMENT 2016 REAR LOAD PACKER TRUCK BID PACKET

2 ADDRESS TO SEND BIDS: BIDS MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE ENVELOPE AS FOLLOWS: AWARD OF CONTRACT SANITATION DEPARTMENT REAR LOAD PACKER TRUCK AND SENT TO: CITY OF LANCASTER SERVICE SAFETY DIRECTOR 104 EAST MAIN STREET, RM 102 LANCASTER, OH The Director of Public Safety and Service (the Director ) reserves the right to reject any or all bids. Bid price alone shall not be the determining factor in selecting the best bid, but rather the m erits and advantages to the City of Lancaster of each bid shall be taken into consideration in awarding the contract. BID DEADLINE Bids must be received no later than 11:00 a.m. on Thursday, June 9, 2016, at the above address. Bids received after this deadline will be returned, to the bidder, unopened. CONTACT PERSON BONDING Bill Burrows, Superintendent, Lancaster Sanitation Department Telephone: (740) Fax: (740) bburrows@ci.lancaster.oh.us All bidders shall furnish with its bid a bid bond or certified check in the sum of FIVE PERCENT (5%) of the total bid submitted, to the satisfaction of the Director on some solvent bank, as a guarantee that if the bid is accepted a contract will be entered into, and a TEN PERCENT (10%) performance bond for the total amount of the contract will be properly secured for the duration of the contract. INSTALLATION AND DELIVERY The one (1) 20 Yard load Packer Truck specifications listed he rein must be installed on a or newer Freightliner M2 106 conventional chassis ( see chassis specifications included). Bid must include all components necessary for one (1) complete 20 Yard rear load packer truck ready for intended use upon delivery REAR LOAD PACKER TRUCK DETAILED SPECIFICATIONS 2 Model Profile

3 S P E C I F I C A T I O N F o r Freightliner M2 106 CONVENTIONAL CHASSIS Price Level Data Version M2 PRL-72D (EFF:03/03/08) SPECPRO21 DATA RELEASE VER 004 Vehicle Configuration General Service Truck Service Engine 3 M2 106 CONVENTIONAL CHASSIS 5,170 2, MODEL YEAR SPECIFIED SET BACK AXLE - TRUCK STRAIGHT TRUCK PROVISION LH PRIMARY STEERING LOCATION TRUCK CONFIGURATION DOMICILED, USA 50 STATES (INCLUDING CALIFORNIA AND CARB OPT-IN STATES) REFUSE SERVICE SANITATION BUSINESS SEGMENT MOIST BULK COMMODITY TERRAIN/DUTY: 100% (ALL) OF THE TIME, IN TRANSIT, IS SPENT ON PAVED ROADS MAXIMUM 8% EXPECTED GRADE SMOOTH CONCRETE OR ASPHALT PAVEMENT - MOST SEVERE IN-TRANSIT (BETWEEN SITES) ROAD SURFACE MEDIUM TRUCK WARRANTY EXPECTED FRONT AXLE(S) LOAD : lbs EXPECTED REAR DRIVE AXLE(S) LOAD : lbs EXPECTED GROSS VEHICLE WEIGHT CAPACITY : lbs REFUSE, REAR PACKER BODY - UNLOADS IN A LANDFILL EXPECTED TRUCK BODY LENGTH : 0.0 ft EXPECTED BODY/PAYLOAD CG HEIGHT ABOVE FRAME "XX" INCHES : 32.0 CUM ISC RPM, 2200 GOV, RPM Electronic Parameters Engine Equipment ROAD SPEED LIMIT MPH : 68.0 VSS ANTI-TAMPERING - YES 2010 EPA/CARB EMISSION CERTIFICATION 2010 CARB EMISSION CERTIFICATION - CLEAN IDLE (INCLUDES 6 INCHX4 INCH LABEL ON LEFT SIDE OF HOOD) ENGINE MOUNTED OIL CHECK AND FILL ONE PIECE VALVE COVER

4 4 SIDE OF HOOD AIR INTAKE WITH FIREWALL MOUNTED DONALDSON AIR CLEANER LN 12V 160 AMP LONG BRUSH 2180 PAD 10 MOUNT ALTERNATOR WITHOUT LAMP DRIVER (2) ALLIANCE MODEL 1131, GROUP 31, VOLT MAINTENANCE FREE 1850 CCA THREADED STUD BATTERIES BATTERY BOX FRAME MOUNTED SINGLE BATTERY BOX FRAME MOUNTED LH SIDE UNDER CAB FRAME GROUND RETURN FOR BATTERY CABLES NON-POLISHED BATTERY BOX COVER BATTERY SHUTOFF SWITCH(ES) IN CAB 8 MOUNTED OUTBOARD OF DRIVER SEAT CUMMINS 18.7 CFM COMPRESSOR WITH INTERNAL SAFETY VALVE STEEL AIR COMPRESSOR DISCHARGE LINE WITH INTEGRAL QUICK CONNECT SYSTEM CHARGING VALVE ELECTRONIC ENGINE INTEGRAL WARNING AND DERATE PROTECTION SYSTEM RH INBOARD FRAME MOUNTED HORIZONTAL AFTERTREATMENT DEVICE WITH RH CAB MOUNTED VERTICAL TAILPIPE ROUTED UNDER FRAME ENGINE AFTERTREATMENT DEVICE, AUTOMATIC OVER THE ROAD REGENERATION AND DASH MOUNTED REGENERATION REQUEST SWITCH 11 FOOT 06 INCH (138 INCH+0/-5 INCH) EXHAUST SYSTEM HEIGHT RH CURVED VERTICAL TAILPIPE B- PILLAR MOUNTED ROUTED UNDER FRAME STAINLESS STEEL AFTERTREATMENT DEVICE/MUFFLER/TAILPIPE SHIELD HORTON DRIVEMASTER ON/OFF FAN DRIVE AUTOMATIC FAN CONTROL WITHOUT DASH SWITCH, NON ENGINE MOUNTED CUMMINS SPIN ON FUEL FILTER COMBINATION FULL FLOW/BYPASS OIL FILTER 1100 SQUARE INCH ALUMINUM RADIATOR 20 ANTIFREEZE TO -34F, ETHYLENE GLYCOL PRE-CHARGED SCA HEAVY DUTY COOLANT GATES BLUE STRIPE COOLANT HOSES CONSTANT TENSION HOSE CLAMPS FOR COOLANT HOSES LOWER RADIATOR GUARD PHILLIPS-TEMRO 1000 WATT/115 VOLT BLOCK HEATER

5 Transmission BLACK PLASTIC ENGINE HEATER RECEPTACLE MOUNTED UNDER LH DOOR ALUMINUM FLYWHEEL HOUSING ELECTRIC GRID AIR INTAKE WARMER 10 DELCO 12V 38MT HD STARTER WITH INTEGRATED MAGNETIC SWITCH ALLISON 3500 RDS AUTOMATIC TRANSMISSION WITH PTO PROVISION Transmission Equipment WTEC CALIBRATION - 6 SPEED RDS WITH AUTO NEUTRAL (PACKAGE 168) VEHICLE INTERFACE WIRING AND PDM WITH BODY BUILDER CONNECTOR, BACK OF CAB ELECTRONIC TRANSMISSION CUSTOMER ACCESS CONNECTOR MOUNTED BACK OF CAB CHELSEA 277 SERIES CUSTOMER INSTALLED PTO PTO MOUNTING, LH SIDE OF MAIN TRANSMISSION MAGNETIC PLUGS, ENGINE DRAIN, TRANSMISSION DRAIN, AXLE(S) FILL AND DRAIN PUSH BUTTON ELECTRONIC SHIFT CONTROL, DASH MOUNTED TRANSMISSION PROGNOSTICS - DISABLED(N/A) WATER TO OIL TRANSMISSION COOLER, IN RADIATOR END TANK TRANSMISSION OIL CHECK AND FILL WITH ELECTRONIC OIL LEVEL CHECK SYNTHETIC TRANSMISSION FLUID (TES- 295 COMPLIANT) Axle and Equipment MFS A 16,000# FL1 SINGLE FRONT 290 AXLE MERITOR 16.5X6 Q+ CAST SPIDER CAM 100 FRONT BRAKES, DOUBLE ANCHOR, FABRICATED SHOES NON-ASBESTOS FRONT BRAKE LINING CONMET CAST IRON FRONT BRAKE DRUMS FRONT BRAKE DUST SHIELDS 5 CHICAGO RAWHIDE SCOTSEAL PLUS XL FRONT OIL SEALS VENTED FRONT HUB CAPS - OIL STANDARD SPINDLE NUTS FOR ALL AXLES MERITOR AUTOMATIC FRONT SLACK ADJUSTERS TRW TAS-85 POWER STEERING 50 POWER STEERING PUMP

6 Suspension 2 QUART SEE THROUGH POWER STEERING RESERVOIR SYNTHETIC 75W-90 FRONT HUBS LUBE 12,000# TAPERLEAF FRONT SUSPENSION 40 MAINTENANCE FREE RUBBER BUSHINGS - FRONT SUSPENSION FRONT SHOCK ABSORBERS 30 Axle and Equipment Suspension Brake System RS ,000# U-SERIES SINGLE REAR 460 AXLE 5.86 REAR AXLE RATIO IRON REAR AXLE CARRIER WITH STANDARD AXLE HOUSING 17N MERITOR MAIN DRIVELINE WITH FULL ROUND YOKES DRIVER CONTROLLED TRACTION 20 DIFFERENTIAL - SINGLE REAR AXLE (1) DIFFERENTIAL LOCK CONTROL VALVE FOR SINGLE DRIVE AXLE BLINKING LAMP WITH EACH MODE SWITCH, DIFFERENTIAL UNLOCK WITH IGNITION OFF, ACTIVE MERITOR 16.5X7 "P" CAM REAR BRAKES, 50 DOUBLE ANCHOR, CAST SHOES NON-ASBESTOS REAR BRAKE LINING CAM BRAKE AUXILIARY SUPPORT BRACKETS WEBB CAST IRON REAR BRAKE DRUMS REAR BRAKE DUST SHIELDS 5 REAR OIL SEALS HALDEX GOLDSEAL LONGSTROKE 1- DRIVE AXLE SPRING PARKING CHAMBERS GUNITE AUTOMATIC REAR SLACK ADJUSTERS PETROLEUM BASED SAE 80/90 REAR AXLE LUBE REYCO 102CC 31,000# REAR SUSPENSION SPRING SUSPENSION " AXLE SPACER STANDARD U-BOLT PAD AIR BRAKE PACKAGE WABCO 4S/4M ABS WITHOUT TRACTION CONTROL REINFORCED NYLON, FABRIC BRAID AND WIRE BRAID CHASSIS AIR LINES FIBER BRAID PARKING BRAKE HOSE STANDARD BRAKE SYSTEM VALVES RELAY VALVE WITH 5-8 PSI CRACK PRESSURE, NO REAR PROPORTIONING VALVE 6

7 MERITOR WABCO SYSTEM SAVER 1200 HEATED AIR DRYER WITH PRESSURE CONTROL VALVE STEEL AIR BRAKE RESERVOIRS MOUNTED INSIDE RAIL STANDARD AIR SYSTEM PRESSURE PROTECTION SYSTEM PULL CABLE ON WET TANK, PETCOCK DRAIN VALVES ON ALL OTHER AIR TANKS 20 Wheelbase & Frame 5675MM (223") WHEELBASE 11/32"X3-1/2"X10-15/16" STEEL FRAME (8.73MMX277.8MM/.344"X10.94") 120KSI 2275MM (90") REAR FRAME OVERHANG FRAME OVERHANG RANGE: 81 INCH TO 90 INCH SQUARE END OF FRAME STANDARD WEIGHT ENGINE CROSSMEMBER STANDARD REARMOST CROSSMEMBER STANDARD SUSPENSION CROSSMEMBER Chassis Equipment Fuel Tanks Tires THREE-PIECE 14" PAINTED STEEL BUMPER 20 WITH COLLAPSIBLE ENDS FRONT TOW HOOKS - FRAME MOUNTED 15 BUMPER MOUNTING FOR SINGLE LICENSE PLATE CLEAR FRAME RAILS FROM BACK OF CAB TO FRONT REAR SUSPENSION BRACKET, BOTH RAILS INSIDE/OUTBOARD AND BELOW HUCK-SPIN ROUND COLLAR CHASSIS FASTENERS 40 GALLON/151 LITER RECTANGULAR ALUMINUM FUEL TANK - RH 40 GALLON/151 LITER RECTANGULAR ALUMINUM FUEL TANK - LH RECTANGULAR FUEL TANK(S) PLAIN ALUMINUM/PAINTED STEEL FUEL/HYDRAULIC TANK(S) WITH PAINTED BANDS FUEL TANK(S) FORWARD FUEL TANK CAP(S) ALLIANCE FUEL FILTER/WATER SEPARATOR EQUIFLO INBOARD FUEL SYSTEM REINFORCED NYLON FUEL HOSE 11R PLY RADIAL FRONT TIRES

8 Hubs Wheels Cab Exterior MICHELIN XZA3 11R PLY RADIAL FRONT TIRES 11r PLY RADIAL REAR TIRES MICHELIN XDY-11r PLY RADIAL REAR TIRES 24 CONMET PRE-SET BEARING IRON FRONT HUBS WEBB IRON REAR HUBS 70 ACCURIDE X HUB PILOT 10-HAND HSLA STEEL DISC FRONT WHEELS ACCURIDE X HUB PILOT 5-HAND STEEL DISC REAR WHEELS 106" BBC FLAT ROOF ALUMINUM CONVENTIONAL CAB AIR CAB MOUNTS 2-1/2" FENDER EXTENSIONS 10 LH AND RH GRAB HANDLES HOOD MOUNTED CHROMED PLASTIC GRILLE CHROMED HOOD MOUNTED AIR INTAKE GRILLE FIBERGLASS HOOD TUNNEL/FIREWALL LINER SINGLE 11 INCH ROUND AIR HORN UNDER 4 DECK SINGLE ELECTRIC HORN SINGLE HORN SHIELD DOOR LOCKS AND IGNITION SWITCH KEYED THE SAME REAR LICENSE PLATE MOUNT END OF FRAME INTEGRAL HEADLIGHT/MARKER ASSEMBLY WITH CHROME BEZEL (5) AMBER MARKER LIGHTS OMIT STOP/TAIL/BACKUP LIGHTS AND PROVIDE WIRING WITH SEPARATE STOP/TURN WIRES TO 4' BEYOND END OF FRAME STANDARD FRONT TURN SIGNAL LAMPS DUAL WEST COAST BRIGHT FINISH HEATED MIRRORS DOOR MOUNTED MIRRORS 102" EQUIPMENT WIDTH LH AND RH 8" BRIGHT FINISH CONVEX MIRRORS MOUNTED UNDER PRIMARY MIRRORS STANDARD SIDE/REAR REFLECTORS 63 INCHX14 INCH TINTED REAR WINDOW TINTED DOOR GLASS LH AND RH WITH TINTED NON-OPERATING WING WINDOWS

9 Cab Interior MANUAL DOOR WINDOW REGULATORS TINTED WINDSHIELD 8 LITER WINDSHIELD WASHER RESERVOIR WITHOUT FLUID LEVEL INDICATOR OPAL GRAY VINYL INTERIOR MOLDED PLASTIC DOOR PANEL MOLDED PLASTIC DOOR PANEL GRAY VINYL MATS WITH INSULATION FORWARD ROOF MOUNTED CONSOLE WITH UPPER STORAGE COMPARTMENTS WITHOUT NETTING IN DASH STORAGE BIN (2) CUP HOLDERS LH AND RH DASH GRAY/CHARCOAL FLAT DASH HEATER, DEFROSTER AND AIR CONDITIONER STANDARD HVAC DUCTING MAIN HVAC CONTROLS WITH RECIRCULATION SWITCH STANDARD HEATER PLUMBING SANDEN HEAVY DUTY AIR CONDITIONER COMPRESSOR BINARY CONTROL, R-134A CAB INSULATION SOLID-STATE CIRCUIT PROTECTION AND FUSES 12V NEGATIVE GROUND ELECTRICAL SYSTEM DOME LIGHT WITH 3-WAY SWITCH ACTIVATED BY LH DOOR(S) CAB DOOR LATCHES WITH MANUAL DOOR LOCKS BOSTROM TALLADEGA 910 HIGH BACK AIR SUSPENSION DRIVER SEAT 2 MAN TOOL BOX MID BACK NON SUSPENSION PASSENGER SEAT LH AND RH INTEGRAL DOOR PANEL ARMRESTS BLACK CORDURA PLUS CLOTH DRIVER SEAT COVER BLACK CORDURA PLUS CLOTH PASSENGER SEAT COVER 3 POINT DRIVER AND PASSENGER AND 2 POINT CENTER FRONT SEAT BELT RETRACTORS FIXED STEERING COLUMN 4-SPOKE 18" (450MM) STEERING WHEEL DRIVER AND PASSENGER INTERIOR SUN VISORS Instruments & Controls ENGINE REMOTE INTERFACE WITH PARK BRAKE AND NEUTRAL INTERLOCKS BLACK GAUGE BEZELS GRAY DRIVER INSTRUMENT PANEL

10 GRAY CENTER INSTRUMENT PANEL LOW AIR PRESSURE LIGHT AND BUZZER 2" PRIMARY AND SECONDARY AIR PRESSURE GAUGES ENGINE COMPARTMENT MOUNTED AIR RESTRICTION INDICATOR WITH GRADUATIONS, WITH WARNING LIGHT IN DASH ELECTRONIC CRUISE CONTROL WITH SWITCHES IN LH SWITCH PANEL KEY OPERATED IGNITION SWITCH AND INTEGRAL START POSITION; 4 POSITION OFF/RUN/START/ACCESSORY ODOMETER/TRIP/HOUR/DIAGNOSTIC/VOL TAGE DISPLAY: 1X7 CHARACTER, 26 WARNING LAMPS, DATA LINKED, ICU3 DIAGNOSTIC INTERFACE CONNECTOR, 9 PIN, SAE J1587/1708/1939, LOCATED BELOW DASH 2" ELECTRIC FUEL GAUGE ENGINE REMOTE INTERFACE WITH PRESET FAST IDLE ENGINE REMOTE INTERFACE AT BACK OF CAB ELECTRICAL ENGINE COOLANT TEMPERATURE GAUGE 2" TRANSMISSION OIL TEMPERATURE GAUGE ENGINE AND TRIP HOUR METERS INTEGRAL WITHIN DRIVER DISPLAY ELECTRIC ENGINE OIL PRESSURE GAUGE AM/FM/WB/CD/MP3 PREMIUM RADIO 10 DASH MOUNTED RADIO (2) RADIO SPEAKERS IN CAB MULTI-BAND AM/FM/WB/CB LH MIRROR MOUNTED ANTENNA SYSTEM ELECTRONIC MPH SPEEDOMETER WITH SECONDARY KPH SCALE, WITHOUT ODOMETER ELECTRONIC 3000 RPM TACHOMETER IGNITION SWITCH CONTROLLED ENGINE STOP NO TRAILER HAND CONTROL BRAKE VALVE DIGITAL VOLTAGE DISPLAY INTEGRAL WITH DRIVER DISPLAY SINGLE ELECTRIC WINDSHIELD WIPER MOTOR WITH DELAY MARKER LIGHT SWITCH INTEGRAL WITH HEADLIGHT SWITCH ONE VALVE PARK BRAKE SYSTEM WITH DASH VALVE CONTROL AUTONEUTRAL AND WARNING INDICATOR SELF CANCELING TURN SIGNAL SWITCH WITH DIMMER, WASHER/WIPER AND HAZARD IN HANDLE 2 10

11 Design INTEGRAL ELECTRONIC TURN SIGNAL FLASHER WITH HAZARD LAMPS OVERRIDING STOP LAMPS Color PAINT: ONE SOLID COLOR CAB COLOR A: N0006EA WHITE ELITE SS BLACK, HIGH SOLIDS POLYURETHANE CHASSIS PAINT ACCURIDE PKWHT21 POWDER WHITE (N0006EA) FRONT WHEELS/RIMS ACCURIDE PKWHT21 POWDER WHITE (N0006EA) REAR WHEELS/RIMS BUMPER PAINT: FP24812 ARGENT SILVER DUPONT FLEX 11

20 YARD STANDARD REAR LOADER B O D Y S P E C I F I C A T I O N S Floor: 3/16 AR200 (one piece) Floor Braces (width): 3/16 GRD 50 high strength Steel Floor Braces (length): C8 x 11.

12 20 YARD STANDARD REAR LOADER B O D Y S P E C I F I C A T I O N S Floor: 3/16 AR200 (one piece) Floor Braces (width): 3/16 GRD 50 high strength Steel Floor Braces (length): C8 x 11.5 Channel Floor Shelf: 5/16 AR200 Side Wall, Section: 1/8 AR500 Side Wall, Section: 10 Gauge AR200 Side Post: 3/16 GRD 50 high strength Steel Roof: 10 Gauge AR200 : 3/16 GRD 50 high strength Steel (weldment) Access Door: 23 ½ x 29 ½ (located streetside) Body Bolsters: 10 Gauge GRD 50 high strength Steel H O P P E R S P E C I F I C A T I O N S 3.0 Cubic Yard Tailgate Capacity 55 ½ Hopper Opening Height 80 Hopper Width 50 Hopper Tailgate Seal Height Hopper Braces and Support: 3/16 GRD 50 high strength Steel Upper Braces and Support: 11 Gauge GRD 50 high strength Steel (formed channel) Floor: ¼ AR200 Loading Edge: ¼ GRD 50 high strength Steel Sides (bottom half): 3/16 AR200 Sides (top half): 11 Gauge GRD 50 high strength Steel Tracks: ¼ GRD 50 high strength Steel Wear Strips: ½ x Steel S L I D E S P E C I F I C A T I O N S Face: 3/16 GRD 50 high strength Steel Side Plates: ½ GRD 50 high strength Steel Braces: 3/16 GRD 50 high strength Steel Slide Shoes: A500 GRD B Rectangular Tubing with (2) 4 x 14 lower and (2) 4 x 14 upper high performance self-lubricating polymer pads P A C K I N G P A N E L Face Plate: ¼ AR200 Cylinder Supports: ½ GRD 50 high strength steel plate Braces: ¼ GRD 50 high strength Steel Ribs: 3/8 GRD 50 high strength Steel Packer Edge Strip: ¾ GRD 50 high strength Steel Packer Bearing: 3 ½ ID Bronze Bushings E J E C T O R

13 Upper Vertical Face: 11 Gauge GRD 50 high strength Steel Lower Sloped Face: 10 Gauge A569 HR Steel Braces: C4 x 5.4 Structural Channel with ¼ welded structure Slide Blocks: UHMW Plastic (4 pieces per side) Track Guides: ¼ GRD 50 high strength Steel Gussets: ¼ GRD 50 high strength Steel Ejector Cylinder center mounted with a 45 degree welded mount assembly with 1 sides and 3/8 base fully welded to floor of body H Y D R A U L I C S Pump Make/Model: Commercial Intertech (front mount model: P75, transmission mount model: P365) Pump Size: P75 1 ¾, P365 2 x 2 Pump Flow: RPM Control Valves: Commercial Intertech VA35, MRV Setting 2700 psi Oil Reservoir: Oil Reservoir: Filter: Parker 40 CN Suction Strainer: 100 mesh stainless steel with magnets C Y L I N D E R S Ejector Cylinder: Ejector Cylinder: Sweep Cylinder: 4 bore x 3 cylinder size x 23 stroke Slide Cylinder: 4½ bore x 3½ cylinder size x 32 ½ stroke Tailgate Cylinder: 2.88 bore x 2 ½ cylinder size x 38 stroke H A R D W A R E Weather Pak Connector Deutsch Connectors Aeroquip Hoses and Fittings Hydra-Zorb and Stauff Clamps lights, signal lights, and back-up lights are 4 Truk-Lite brand with Bowman brand fasteners W A R R A N T I E S Cylinders: 5 year limited warranty from date of delivery Hydraulic Pump and Valves: 2 years from date of delivery Packer Unit: 6 months from date of delivery P A I N T I N G Packer and components steel shot blasted prior to priming with high solids epoxy primer. Finish Coat Akzo Coating's Sikkens high solids acrylic urethane. Solid white standard.

14 Options Included in Price: Trapezoidal Lights 12,000# Reeving Cylinder Container Guides and Latches Mud Flaps of Drives Bayne BTL 208 Cart Lifter Hopper Work Lights (2) AM/FM Radio Air Conditioner Hopper, Shelf and Sidewall Liner 3/16 AR200 Fire Extinguisher & Bracket Paint Body: White Paint Cab: White Side Door Ladder w/shutdown LITERATURE Must include full set of operation, maintenance and parts manuals. Electrical schematics for packer body.

15 BID PROPOSAL I/WE, THE BELOW SIGNED BIDDER, HEREBY PROPOSE TO FURNISH THE SPECIFIED ARTICLE(S), AT THE PRICE(S) AND TERMS STATED HEREIN, SUBJECT TO ALL INSTRUCTIONS, CONDITIONS, SPECIFICATIONS, AND ATTACHMENTS HERETO. I/WE HAVE READ ALL ATTACHMENTS INCLUDING THE SPECIFICATIONS AND FULLY UNDERSTAND WHAT IS REQUIRED. PRICES ARE TO BE QUOTED F.O.B.: CITY OF LANCASTER SANITATION DEPARTMENT 743 SOUTH EWING STREET LANCASTER, OHIO QTY UNIT ITEM DESCRIPTION Total Price for Both 1 EA YD REARLOAD PACKER TRUCKS $ TOTAL PRICE IN WRITING: DELIVERY WITHIN: CALENDAR DAYS AFTER RECEIPT OF ORDER. NAME OF COMPANY/BIDDER: ADDRESS OF COMPANY/BIDDER: AUTHORIZED SIGNATURE: X (Signature must be in writing in other than black ink) TITLE: DATE: THESE SPECIFICATIONS ARE MEANT TO BE DESCRIPTIVE AND IN NO WAY RESTRICTIVE. ANY AND ALL EXCEPTIONS MUST BE NOTED.

NELSON COUNTY FISCAL COURT

NELSON COUNTY FISCAL COURT Specifications/Bid Forms FOR 25 CUBIC YARD REAR PACKER,REAR EJECTION, GARBAGE TRUCK DATE: 08/2017 ADVERTISEMENT FOR BIDS The Nelson County Fiscal Court will accept sealed bids