Replacing the fuel tank
|
|
- Kristopher Shields
- 5 years ago
- Views:
Transcription
1 Page 1 of 11 Replacing the fuel tank Special tools: Preparation Note! On cars up to chassis number the fuel filler pipe must be replaced when the fuel tank is replaced. Drain the fuel from the lines. See Draining the fuel system. Drain the fuel tank. See Draining the fuel tank. Removing the rear exhaust system Raise the car. both the rear wheels the front section of the exhaust system. Removing the heat deflector plate Remove the rear plastic nut from the lefthand wing liner. Drill out the pop rivets which hold the heat deflector plate at the rear subframe mounting and the exhaust system bracket. the plastic nuts holding the heat deflector plate the heat deflector plate. Exposing the fuel tank the plastic pipe with the largest connection to the carbon filter container. Position the pipe forwards towards the fuel tank the screws on the centre and left mountings of the heat deflector plate for the fuel tank the brake pipe from the clip in the front edge of the tank the fuel filter from the bracket the hose clamp from the fuel filler pipe and
2 Page 2 of 11 the hose clamp from the fuel filler pipe and the bleed pipe. Removing the brakes the mounting screws for the brake calliper. Hang the brake calliper in a suitable way the locating pins for the brake discs the brake discs. Hint: If necessary release the handbrake shoes. See Handbrake, brake shoes, replacing Removing the handbrake cable the return spring at the expander the expander. Lift the brake shoe slightly unhook the expander from the cable mounting. Remove the guide sleeve for the cable sleeve. Use a screwdriver. Pry carefully between the guide sleeve lug and the spindle. Remove the handbrake cable from the track rod and subframe. Bend the handbrake cables forward. Hang the handbrake cable from the front SIPS member. Lowering the fuel tank Position a lifting table under the fuel tank.
3 Page 3 of 11 Remove the tank retaining strap screws. Lower the fuel tank slightly. The ABS lines from the clips The fuel filler pipe and the bleed pipe from the fuel tank terminals. Lower the fuel tank slightly further. fuel lines the plastic pipe between the carbon filter container and the evaporative emission system (EVAP) valve from the upper side of the tank. Lower the tank completely. Note! Check that the lines and wiring are unimpeded during the rest of the lowering of the tank. Applies only to cars with chassis numbers below Replace the fuel filler pipe. See Replacing the fuel filler pipe (When replacing the fuel tank). Transferring components Removing the fuel tank pressure valve Disconnect the hose (hose clamp). the screw the valve. Removing the splash guard pipe Remove the splash guard pipe. Pull straight out.
4 Page 4 of 11 Removing the level sensor Lift the left level sensor. the connector the ejector. Grip the righthand level sensor / pump. Pinch the float to hold it in its lowest position. Carefully and slowly pull up the holder. Carefully work the holder out. Pull the hoses and the wiring out of the tank. Note! Take care with the fuel tank. Note! It is extremely important that the float arm is not broken or bent. Removing the tank retaining strap and heat deflector plate the screws (x 2) the tank retaining strap the screws (x 2) the heat deflector plate. Installing the tank retaining strap and heat deflector plate the heat deflector plate the 2 screws. Tighten to 5 Nm the tank retaining strap the 2 screws. Tighten to 10 Nm.
5 Page 5 of 11 Installing the level sensor Install the sealing ring. Route the cable harness / hoses from the right level sensor to the left side of the tank as illustrated. Hint: Use a welding rod bent into a curve with a hook at one end to pull the cable harness / hoses to the correct position. Note! It is very important for installing the level sensor that the cable harness / hoses are routed into the front section of the fuel tank. Install on the lefthand side: sealing cover the ejector the connectors the level sensor. Tighten to 60 Nm. (Use special tool ). Note! Ensure that the arrow is opposite the marking on the tank. Install on the righthand side: the level sensor. Tighten to 60 Nm. (Use special tool ). Ensure that the arrow is opposite the marking on the tank.
6 Page 6 of 11 Installing the splash guard pipe Install the splash guard pipe. Note! Ensure that the locating pin is correctly positioned for the groove in the tank. Installing the fuel tank pressure valve the valve the screw the hose (hose clamp). Installing the fuel tank Position the fuel tank on the lifting table. Raise the fuel tank to a suitable height so that the fuel lines and plastic pipes between the carbon filter container and the evaporative emission system (EVAP) valve can be positioned in their terminals on the upper side of the fuel tank. Connect the fuel lines to the right level sensor / pump as illustrated. Route the electrical wiring to the passenger compartment through the floor.
7 Page 7 of 11 Lift the fuel tank up completely. Ensure that no lines or wiring are trapped. Install the fuel filler pipe and the bleed pipe on the fuel tank at the same time. Twist the hose clamps so that they can be easily tightened later. Note! Always use new hose clamps. Install the ABS wiring in its clips. Tighten the tank retaining strap screws. Tighten to 25 Nm. Install the fuel filter and console. Tighten to 25 Nm. Installing the brakes the handbrake cable along the heat shields the screws in the centre and front mountings for the heat shield. the handbrake cables on the wheel units the handbrake cable mountings in the subframe. (25 Nm ) the mounting for the handbrake cable on the track rods. Press the guide sleeves for the handbrake cables into place on the wheel units. Hint: Lubricate the Orings on the guide sleeves. Use lubricant or silicon grease. the expander on the cable. Press the
8 Page 8 of 11 mounting together to lock the cable in the expander the expander between the brake shoes the return spring. Check the function. the brake disc and the locating pin. Tighten to 10 Nm the brake calliper. Use new screws. Tighten to 60 Nm. Note! If necessary, adjust the handbrake. See Handbrake, brake shoes, replacing Install the plastic pipe from the fuel tank with the large connector on the carbon filter container. Note! A click should be heard when the connector is pressed into place. Installing the heat deflector plate Position the heat deflector plate over the rear silencer. Install the plastic nuts and the rear pop rivet. Install the pop rivets on the rear mounting of the subframe. Install the rear wheels. See Installing wheels. Installing exhaust system Install the exhaust system. Use a new flange gasket. Tighten the screws. Tighten to 25 Nm.
9 Page 9 of 11 Finishing the 23 connectors on the right side and the 2 connectors on the left side the cover over the level sensors. Check that the wiring is correctly located in the groove in the rubber gaskets around the hole in the floor insulation panel the backrest. Replacing the carbon filter container Removing the heat deflector plate Remove the exhaust system (from the threeway catalytic converter (TWC) and downstream) as illustrated. Remove the left rear wheel. Remove the rear plastic nut from the plastic fender liner. Drill out the two blind rivets holding the heat deflector plate at the rear subframe mounting and the third rivet on the rear bracket for the exhaust system. Use a 5 mm drill bit Remove the plastic nuts and the heat deflector plate. Removing the carbon filter container
10 Page 10 of 11 Disconnect the thick plastic pipe. Press the pipe towards the carbon filter container. Press in the two catches. Disconnect the thin plastic pipe. Press in the catches. These are positioned forward towards the fuel tank. Pull off the pipe. Disconnect the plastic pipe from the clip. Remove the rubber hose from the carbon filter container and the tie strap. Remove the clamp holding the rubber hose (onboard vapor recovery (ORVR) fuel tanks only). Remove the shutoff valve from the bracket. Pull the shutoff valve straight up (ORVR fuel tanks only). Remove the two screws that secure the bracket. Pull the bracket and the carbon filter container down. Disconnect the carbon filter container from the bracket. Installing the carbon filter container Install the carbon filter container on the bracket. Tighten the screw. Tighten to 10 Nm. Place the bracket and carbon filter container against the subframe. (ORVR fuel tanks only) Press the shutoff valve into place on the bracket. Install a new hose clamp on the rubber hose. Install the rubber hose on the carbon filter container and the tie strap. Install the two screws that secure the bracket. Tighten to 25 Nm. Install the thin plastic pipe in the clip on the carbon filter container. A click should be heard. Installing the heat deflector plate Install the heat deflector plate and the plastic nuts the pop rivets. Install one rivet at the bracket for the exhaust system and two rivets on the rear mounting for the subframe the left rear wheel.
11 Page 11 of 11 Install the exhaust system. Use a new gasket. Tighten the nuts. Tighten to 25 Nm. Tighten the screws. Tighten to 25 Nm. Replacing the shutoff valve for the carbon filter container Replacing the shutoff valve for the carbon filter container Removing the shutoff valve Remove the carbon filter container according to Replacing the carbon filter container. Disconnect the connector, clamps and hoses from the EVAP canister shutoff valve. Remove the EVAP canister shutoff valve. Installing the shutoff valve Install the clamps and hoses on the shutoff valve. Check that the hoses are correctly positioned and are not twisted or kinked. Connect the connector. Press the quickrelease connector together until a clicking sound is heard. Install the carbon filter container according to Replacing the carbon filter container.
Installation instructions, accessories - Fuel driven heater 912-D
XC90 Section Group Weight(Kg/Pounds) Year Month 8 87 2002 10 XC90 2003 D5244T, XC90 2004 D5244T, XC90 2005 D5244T AW50/51 AWD, XC90 2006 D5244T, XC90 2006 D5244T AW50/51 AWD D5244T R8703687 Page 1 of 20
More informationRemoving/installing final drive
1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm
More informationFuel pump unit, changing
1(11) Fuel pump unit, changing Special tools: 981 2270, 981 2273, 981 2282, 998 5972, 999 5484, 999 5485, 999 5561, 999 5666, 999 5673 Safety See first Safety regulations for handling fuel. Preparation
More informationFUEL PUMP UNIT, REPLACEMENT. Special tools: , , , , , , , ,
FUEL PUMP UNIT, REPLACEMENT Special tools: 981 2270, 981 2273, 981 2282, 998 5972, 999 5484, 999 5485, 999 5561, 999 5666, 999 5673 Safety See first: Safety regulations for handling fuel See: Service Precautions
More informationPage 1 of 10 43: Transmission, automatic, B5254T2, AW50/51 AWD V70 XC (01-) / XC70 (-07), 2004, B5254T2, AW50/51 AWD, L.H.D, YV1SZ59H241147306, 147306 15/10/2011 PRINT 43: Transmission, automatic, B5254T2,
More information900 Installation instructions. SCdefault
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationFront seats. Special tools and equipment. VAS 5094 airbag adapter. Connecting page 72-9.
Page 1 of 23 72-1 Front seats Special tools and equipment VAS 5094 airbag adapter Connecting page 72-9. Page 2 of 23 72-2 Front seats, removing and installing WARNING! Before starting work on seats, connect
More informationInstallation instructions, accessories RTI S80
Installation instructions, accessories Instruction No 8685714 Version 1.0 5 Part. No. RTI S80 Volvo Car Corporation RTI S80-8685714 - V1.0 Page 1 / 25 Equipment A0000161 A0000162 A0801178 D8802049 Page
More informationInstallation instructions, accessories - Electric engine block heater
S60 / V70 (00-08) / S80 (-06) / V70 XC (01-) / XC70 (-07) / XC90 Section Group Weight Year Month (Kg/Pounds) 8 876 2/4.4 2006 09 S60 2001 D5244T, S60 2002 D5244T, S60 2002 D5244T2, S60 2003 D5244T, S60
More informationReplacing the sump. Copyright 2004 Volvo Car Corporation. All rights reserved.
"VCC139128 EN 20100619" 1(6) Replacing the sump Special tools: 951 1205, 999 5460, 999 5716, 999 5717 Note! As the illustrations in this service information are used for different model years and / or
More informationShock absorber front, replacing. Spring/shock absorber rear, replacing
"VCC146099 EN 20090331" 1(12) Shock absorber front, replacing Special tools: 999 5407 Removing the shock absorber Spring/shock absorber rear, replacing Remove and disassemble the spring strut. See Spring
More informationInstallation instructions, accessories. Electric engine block heater, 230V, 5 cyl diesel
Installation instructions, accessories Instruction No 30795311 Version 1.2 Part. No. 31373138 Electric engine block heater, 230V, 5 cyl diesel IMG-256423 Volvo Car Corporation Electric engine block heater,
More informationInstallation instructions, accessories. Subwoofer
Installation instructions, accessories Instruction No 9162298 Version 1.0 5 Part. No. Subwoofer Volvo Car Corporation Subwoofer - 9162298 - V1.0 Page 1 / 24 Equipment A0000162 A0801178 A0000161 R8802817
More informationInstallation instructions, accessories. Body kit
Installation instructions, accessories Instruction No 31265373 Version 1.1 5 Part. No. Body kit IMG-256263 Volvo Car Corporation Body kit - 31265373 - V1.1 Page 1 / 42 Equipment A0000162 A0000163 IMG-239664
More information1999 Volvo V70 AWD ENGINE PERFORMANCE Removal & Installation - Except S40 & V40
Removal (S70, V70 AWD & V70 XC) 1. Drain fuel tank. See DRAINING FUEL TANK (C70, S70 & V70). Drain fuel system. 2. Remove front and rear cargo compartment floor. Unplug ABS sensor and fuel gauge connectors.
More informationPage 1 of 11 43: Transmission, automatic, B5244T3, AW55-50/51SN V70 (00-08), 2003, B5244T3, AW55-50/51SN, L.H.D, YV1SW58D132320765, 320765 29/3/2014 PRINT 43: Transmission, automatic, B5244T3, AW55-50/51SN
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationSCdefault. 900 Installation instructions. Accessories Part No. Group Date Instruction Part No. Replaces :40-05 Sep
SCdefault 900 Installation instructions SITdefault Parking assistance (SPA) MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationReplacing Steering Gear. Special Tools
Replacing Steering Gear Special Tools 999 5716 999 5259 999 5460 Note! Ensure that the front wheels are pointing straight ahead. Also lock the steering wheel with the steering lock before detaching tie
More information1 of 21 9/30/2011 3:16 PM
Engine Block Heater, Service and Repair, Removal and Replacement: Ele... 1 of 21 9/30/2011 3:16 PM 2005 Volvo S60 L5-2.5L Turbo VIN 59 B5254T2 Engine Block Heater Service and Repair, Removal and Replacement:
More informationSaab 9-3 CV M04-, 4D/5D M06-
SCdefault 900 Installation instructions SITdefault MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Sports chassis Accessories Part No. Group Date Instruction Part
More informationInstallation instructions, accessories. Electric engine block heater, connector outlet, 4-cyl
Installation instructions, accessories Instruction No 31359444 Version 1.2 5 Part. No. 31359438 Electric engine block heater, connector outlet, 4-cyl IMG-247665 Volvo Car Corporation Electric engine block
More informationDraining the fuel system
1(6) Draining the fuel system Special tools: 981 2270, 981 2273, 981 2282, 999 5480, 999 5484 Safety See Safety regulations for handling fuel. Engagement Remove the cover on the valve which is positioned
More informationCylinder head/gasket, replacing
1(16) Cylinder head/gasket, replacing Special tools: 951 2666, 951 2767, 999 5450, 999 5452, 999 5454, 999 5670, 999 5718, 999 5719, 999 5750, 999 5972 Removing the cylinder head gasket Note! As the illustrations
More information393: Multimedia system for the rear seat Multimedia system for the rear seat
393: Multimedia system for the rear seat S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 393: Multimedia system for the rear seat Multimedia system for the rear seat
More information2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing
1 of 25 8/18/2011 6:10 PM 2004 Volvo C70 L5-2.4L Turbo VIN 63 B5244T7 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head/Gasket, Replacing Cylinder head/gasket, replacement
More informationInstallation instructions, accessories - Rear Seat Entertainment
XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 2004 10 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008 Replaces issue: 2003 12 J3904620 Page 1 of 18 Required tools A0000162 A0000163
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Sports chassis MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationFront bumper (Audi RS6)
63-1 Front bumper (Audi RS6) Assembly overview 1 - Air inlet grille To remove pull grille forward 2 - Air inlet grille To remove pull grille forward 3 - Screw 2.5 Nm 3x 4 - Bumper cover Together with impact
More informationFuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)
Page 1 of 49 20-6 Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine) Note: VAG1921 spring clamp pliers are recommended for installation Always replace
More informationTiming Belt: Service and Repair
Timing Belt: Service and Repair REPLACING TIMING BELT/IDLER PULLEY/BELT TENSIONER B 52X4 S Removing timing belt Remove components Caution! Note! Remove the ignition key from the ignition switch before
More informationSpring strut and spring front, replacing
"VCC128825 EN 20090329" 1(7) Spring strut and spring front, replacing Special tools: 951 2911, 951 2914, 951 2915, 951 2564, 999 5500, 999 5576, 999 5758 Removing the spring strut Note! From model year
More informationINSTALLATION INSTRUCTIONS
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0390C APPLICATION: 1999-2003 E39 M5 PARTS LIST 1 Left Aluminum Intake Tube 1 Air Pump Bracket (A) 1 Right Aluminum Intake Tube 1 Air Pump Bracket
More informationRepair manual for Exchanging locking mechanism sensor JSK37C
Repair manual for Exchanging locking mechanism sensor JSK37C JSK_12_48 ZDE 199 7 12 7/213 1 Foreword Table of contents Page Sensor-enabled fifth wheel couplings are parts that must comply with very high
More informationCoolant Pump, Remove and Install (Z 22 SE)
Page 1 of 10 Coolant Pump, Remove and Install (Z 22 SE) Remove 1. Open the bonnet. 2. Disconnect the battery. 3. Open the rear engine cover (1). 4. Detach the rear engine cover. 6 bolts (2) and (3) 5.
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Engine block heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationInstallation instructions, accessories. Parking assistance, rear
Installation instructions, accessories Instruction No 31330676 Version 1.4 Part. No. 30758088, 9487266, 30786087, 31359215 Parking assistance, rear Volvo Car Corporation Parking assistance, rear- 31330676
More informationOil trap electrically heated, replacing
1(5) Oil trap electrically heated, replacing Removing Note! As the illustrations in the information are used for different model years and/or models, some variation may occur. However, the essential information
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
More informationSide panel, replacing
"VCC147307 EN 20110211" 1(23) Side panel, replacing As the illustrations in this service information are used for different model years and / or models, some variation may occur. However, the essential
More informationALLDATA Online Jaguar Vanden Plas V8-3996cc 4.0L DOHC (AJ27) SFI - Fuel...
Page 1 of 7 Removal NOTE: This removal/installation procedure is applicable to all tank assembly variants. 1. Remove the battery. Refer to 'Battery, Service and Repair.' See: Starting and Charging\Battery\Service
More informationBody, front. Lock carrier with attachments, removing and installing
Page 1 of 19 50-1 Body, front Lock carrier with attachments, removing and installing 1 - Hex bolt (6x) 45 Nm (33 ft lb) 2 - Hex bolt 45 Nm (33 ft lb) 3 - Hex bolt (4x) 10 Nm (7 ft lb) 4 - Hex bolts (2x)
More informationInstallation instructions, accessories - Bluetooth, Mute kit XC / Volvo Car Corporation Göteborg, Sweden
XC90 Section Group Weight(Kg/Pounds) Year Month 3 393 0.5/1.1 2006 11 XC90 2003, XC90 2004, XC90 2005, XC90 2006, XC90 2007, XC90 2008, XC90 2009, XC90 2010 Page 1 of 15 Required tools A0000162 IMG-242205
More informationInstallation instructions, accessories. Satellite radio, Sirius
Installation instructions, accessories Instruction No 31201184 Version 1.3 5 Part. No. 31296261, 31359449 Satellite radio, Sirius IMG-246543 Volvo Car Corporation Satellite radio, Sirius- 31201184 - V1.3
More informationInstallation instructions, accessories. Multimedia monitor with DVD, Dual screen. Multimedia monitor with DVD, Dual screen V1.
Installation instructions, accessories Instruction No 30756560 Version 1.2 5 Part. No. 30756177 Multimedia monitor with DVD, Dual screen Volvo Car Corporation Multimedia monitor with DVD, Dual screen-
More informationWiper arm and wiper motor, headlamp, replacing
"VCC137971 EN 20110112" file://c:\info\vv132007\ie\en\31\vcc137971.htm Page 1 of 2 Wiper arm and wiper motor, headlamp, replacing Removal Preparations Switch off the ignition. Headlamp wiper arm Lift up
More information99-04 GT. Hellion Power Systems Mustang GT Kit Instructions
Hellion Power Systems 99-04 Mustang GT Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationTransmission, removing and
Page 1 of 20 34-18 Transmission, removing and installing Removing Special tools and equipment 3282 transmission support 3282/10 adjustment plate 3337 ring spanner 7-piece set VAG1383A engine/transmission
More informationInstallation instructions, accessories - Volvo Navigation System, widescreen
S60 Section Group Weight(Kg/Pounds) Year Month 3 39 2001 04 S60 2001, S60 2002 Page 1 of 21 Page 2 of 21 Required tools A0000162 A0000161 A0801178 M8802509 M3903563 Page 3 of 21 M3903565 M8503983 Page
More informationInstallation instructions, accessories
Volvo Car Corporation Göteborg, Sweden Installation instructions, accessories S60/V70 (00-)/V70XC (01-)/S80/XC90 Section Group Weight (Kg/Pounds) Year Month 8 89 2002 06 Tow bar wiring, 13-pin M3702161
More information394: Handsfree, Bluetooth Handsfree, Bluetooth
394: Handsfree, Bluetooth S80 (07-), 2008, B8444S, TF-80SC AWD, L.H.D, YV1AH852881073834, 073834 4/1/2013 PRINT 394: Handsfree, Bluetooth Handsfree, Bluetooth Installation instruction: 31310098 INTRODUCTION
More informationSaab 9-5 B205, B235, B308
SCdefault 9-5 Installation instructions SITdefault Engine/cabin heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More information50 DISASSEMBLY AND ASSEM- REMOVE AND INSTALL AdBlue/DEF TANK ASSEMBLY
REMOVE AND INSTALL AdBlue/DEF TANK ASSEM 20. After removing drain plug (20), draining amount increases or decreases in approximately 10 seconds. Change tool A to tool D at the timing of decreasing. Insert
More informationEngine, removing and installing
Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers
More informationEngine Removal/Installation
Engine Removal/Installation Make sure jacks and safety stands are placed properly and hoist brackets are attached to correct positions on the engine. (See Section 1). Apply parking brake and block rear
More informationTechnical data. Part Thread (mm) Nm ±10% Tolerance Sidestand
section 3 - Torque settings Frame torque settings Sidestand Stand sensor bolt 5 Pre-applied threadlocker Stand plate fixing screw M10x25 43 Pre-applied threadlocker Side stand fastening pin Side stand
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL SENSOR
More informationParts Manual Rev. A Z 246 /
115 97 16-27 Rev. A Parts Manual Z 246 / 967 844501-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of
More informationLI-ION BATTERY UPFIT KIT
LI-ION BATTERY UPFIT KIT P/N 2881852 APPLICATION E2, E4, E6, and el XD BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationLIBERTY PORTABLE RESTROOM ASSEMBLY INSTRUCTIONS
LIBERTY PORTABLE RESTROOM ASSEMBLY INSTRUCTIONS PN 18041 /REV C 2-10-04 Parts List PN 18041-REV C page 2 INTRODUCTION Satellite portable restrooms must be assembled according to approved assembly procedures.
More informationCylinder head, removing and
Page 1 of 35 15-2 Cylinder head, removing and installing Note: Replace cylinder head bolts. Always replace self-locking nuts, bolts as well as gaskets and O-rings. After installing a replacement cylinder
More informationFUEL SYSTEM SECTION FL CONTENTS B ENGINE FL-1
FUEL SYSTEM B ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Battery Service... 2 PREPARATION... 3 Commercial Service Tools... 3 FUEL SYSTEM... 4 Checking Fuel Lines...
More informationFUEL SYSTEM SECTION CONTENTS B ENGINE FL-1
B ENGINE A SECTION FUEL SYSTEM FL C D CONTENTS E PRECAUTIONS... 2 Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT BELT PRE-TEN- SIONER... 2 PREPARATION... 3 Special Service Tools...
More informationOil pan, oil strainer and valve body, removing and installing
Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace
More information03-04 Mach 1. Hellion Power Systems Mach 1 Kit Instructions
Hellion Power Systems 03-04 Mach 1 Kit Instructions Part 1 Hellion recommends that the front suspension system be installed either by trained professionals or by 5.Remove rack bolts K-Member Installation
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY PFP:17042 Removal and Installation EBS00M47 1. Lock ring 2. Fuel level sensor, fuel filter, and fuel pump assembly FL-6 3. Fuel level sensor,
More informationLuggage System Fitting Instructions - Sprint ST
WARNING: Always have Triumph approved parts, accessories and conversions fitted by a trained technician of an authorised Triumph dealer. The fitting of parts, accessories and conversions by a technician
More informationFUEL SYSTEM SECTION FL CONTENTS B ENGINE FL-1
B ENGINE SECTION FL A FUEL SYSTEM FL C D CONTENTS E PREPARATION... 2 Special Service Tools... 2 Commercial Service Tool... 2 FUEL SYSTEM... 3 Checking Fuel Lines... 3 General Precautions... 3 FUEL LEVEL
More informationDESCRIPTION Acura TSX SUSPENSION Front - TSX. NOTE: For system description and component location, see Fig. 1.
2004 SUSPENSION Front - TSX DESCRIPTION NOTE: For system description and component location, see Fig. 1. Fig. 1: Identifying Front Suspension Components Wednesday, March 12, 2008 8:30:45 8:30:55 PM Page
More informationSCdefault. 900 Installation instructions
SCdefault 900 Installation instructions SITdefault Airbag replacement harness MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction
More informationDrive shaft left-hand side, replace
"VCC126387 EN 20090226" file://c:\info\vv132007\ie\en\30\vcc126387.htm Page 1 of 13 Drive shaft lefthand side, replace Special tools: 9995681 Removal Removing the drive shaft nut the hub cap the drive
More informationParts Manual PZ Please read the operator manual carefully and make sure you understand the instructions before using the machine.
Parts Manual PZ 60 967 045601-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. When you need spare parts or support in service questions,
More informationB5 A4 1.8t Front Mount Intercooler Install Instructions
B5 A4 1.8t Front Mount Intercooler Install Instructions Only work underneath your vehicle after properly supporting it with adequate jack stands on a flat surface. NEVER work under a vehicle only supported
More informationIntake manifold / gasket, replacing
Page 1 of 9 Intake manifold / gasket, replacing Special tools: 999 5723, 951 2666 Preparation Disconnect the battery negative lead. First read Note when disconnecting/connecting the battery lead. Drain
More informationMONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTALLATIONS DE MONTAGE
SCdefault 9-5 Monteringsanvisning SITdefault Engine/cabin heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTALLATIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationPARTS LIST WRANGLER 1710AB, 2010AB 120V AND 240V, TYPE F PLUG
PARTS LIST WRANGLER 1710AB, 2010AB 120V AND 240V, TYPE F PLUG CONTROL PANEL ASSEMBLY 101 1394151 ROUND POWER SWITCH 1 102 0693141 RUBBER SWITCH BOOT 2 103 9122465.516 I.D. X.813 O.D. X.027/.030 THICK FLAT
More information96-04 tt. Hellion Power Systems Mustang Twin Turbo Kit Instructions
96-04 tt Hellion Power Systems 1996-2004 Mustang Twin Turbo Kit Instructions 1. Disconnect battery and elevate front end of car on either Jack stands or a lift if available 2.Lock steering wheel and remove
More information99125B - Series N Brush Lift Assembly Model :99125B 20" EZ Floorkeeper (w/ 4-6 V Batteries) - Series N
995B - Series N Brush Lift Assembly Model :995B 0" EZ Floorkeeper (w/ - V Batteries) - Series N Page- 5 7 9 0 5 7 9 5 7 9 0 5 7 9 0 070 RETAINING RING PIN 9 WASHER 907 WELDMENT BRUSH LIFT PEDAL 900 PEDAL
More informationP/N Instr Rev Page 1 of 11
BRAKE AND CLUTCH KIT P/N 2883864 IMPORTANT Due to the technical nature of this kit, Indian Motorcycle insists this installation be performed by a certified Indian Motorcycle Technician. APPLICATION Verify
More informationSaab 9-5 B205, B Installation instructions MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE.
SCdefault 9-5 Installation instructions SITdefault Parking heater MONTERINGSANVISNING INSTALLATION INSTRUCTIONS MONTAGEANLEITUNG INSTRUCTIONS DE MONTAGE Accessories Part No. Group Date Instruction Part
More informationInstallation Instructions MX-5 Dual Air Horns
440 Rutherford St. P.O. Box 847 Goleta, CA 93117 1-800-667-7872 FAX 805-692-2525 www.mossmotors.com Tools required: Phillips screwdriver, 8mm, 10mm and 21mm sockets, 8mm and 10mm combination wrenches,
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W
B&W Trailer Hitches 6 Hawaii Rd / PO Box 86 Humboldt, KS 66748 P:60.473664 F:60.869.903 Turnoverball Gooseneck Hitch Installation Instructions MODEL 08
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove
More informationGearbox sectional drawing
Gearbox sectional drawing BMW Grafik Design MT- KL39000 3.5 3.6 3 4 77 3 4 77 3473 3 4 7 3 4 7 3 4 73 KL300 Replacing the shaft sealing rings in the gearbox housing and gearbox cover All shaft sealing
More informationDifferential Assembly Remove and Install ( ) Remove. Rear Axle. Special Tools. Workshop Equipment Transmission jack Angle gauge
Differential Assembly Remove and Install (5 54 0) Special Tools 540-540 Angle gauge Workshop Equipment Transmission jack Materials High-temperature grease WSD-MC37-A Remove. Remove the rear part of the
More informationSlave Cylinder Weep Hole Drilling Procedure
Slave Cylinder Weep Hole Drilling Procedure Tools Required: T20 Torx Driver T25 Torx Driver T25 Torx Bit with ¼ Ratchet Wrench 4mm Hex Key (Allen wrench) 5mm Hex Key 6mm Hex Key 8mm Hex Key 12mm Hex Key
More informationClimate control components in passenger compartment, servicing
Page 1 of 34 87-120 Climate control components in passenger compartment, servicing Component electrical testing page 01-115. A/C control head -E87-, removing and installing Notes: Always check DTC memory
More informationCROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT
PAGE 1 OF 6 AFFECTED S: OVERVIEW CROWN VICTORIA POLICE INTERCEPTOR (CVPI) PACKAGE OPTIONAL UPGRADE KIT CERTAIN 1992 THROUGH 2003 MODEL YEAR CROWN VICTORIA POLICE INTERCEPTOR (CVPI) S CURRENTLY IN POLICE
More informationFuel Supply Component Description
1999 Chevrolet/Geo Tahoe - 4WD Fuel Supply Component Description FIGURE Central SFI Fuel System with Fuel Pressure Gauge(c) (1) Fuel Inlet (2) Bleed Hose (3) J 34730-1A Fuel Pressure Gage Assembly (4)
More informationPart # Lincoln Level 2 Air Suspension Package
350 S. St. Charles St. Jasper, In. 47546 Ph. 812.482.2932 Fax 812.634.6632 www.ridetech.com Part # 12060299 64-69 Lincoln Level 2 Air Suspension Package Front Components: 1 12060999 CoolRide Kit 1 12060601
More informationInstallation instructions, accessories - Bluetooth, swan neck microphone
S80 (-06) / V70 XC (01-) / XC70 (-07) / S60 / V70 (00-08) / XC90 / S40 (04-) / V50 / C70 (06-) / S80 (07-) / C30 / V70 (08-) / XC70 (08-) Section Group Weight Year Month (Kg/Pounds) 3 394 0.5/1 2006 10
More informationParts Manual Rev. B RZT48 /
115 91 36-2 Rev. B Parts Manual RZT48 / 96 62001-00 Please read the operator manual carefully and make sure you understand the instructions before using the machine. Gasoline containing a maximum of 10%
More information1501 Industrial Way N., Toms River, NJ Fax: PACKING LIST INSTALLATION INSTRUCTIONS
PART NO. 24050 2004 GTO Line Lock PACKING LIST Item # Check Quantity Part Number Description 1 1 020758100 Solenoid 2 1 020758601 Solenoid to Proportioning Valve Brake Line 3 1 020330601 12mm Bubble Flare
More informationFE 35, 40, 55, EC Every time you open the housing, clean the motor with a soft brush.
FE 35, 40, 55, EC 70 1 Service Manual FE 35, FE 40, FE 55 Electric Trimmers, EC 70 Electric Edger As the design concept of the FE 35 and FE 40 trimmers is almost identical, the descriptions and servicing
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationKIT CONTINUES ON NEXT PAGE
1 Copyright This document contains technical information the property of FORD RANGER 2011-PRESENT - ALL MODELS 145lt REPLACEMENT TANK LONG RANGE FUEL TANK PARTS LIST AND FITTING INSTRUCTIONS PART NUMBER:
More informationSLP Camaro ZL1 STAGE 3 (650 HP)
SLP - 2012 Camaro ZL1 STAGE 3 (650 HP) PART #26002 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION 1. 1
More informationWRANGLER 1708AB, 2008AB
WRANGLER 1708AB, 2008AB WIRING DIAGRAM ITEM PART NO. DESCRIPTION QTY. 1 1393251 WIRE ASSEMBLY - CIRCUIT BREAKER TO BRUSH SWITCH 1 2 1393261 WIRE ASSEMBLY - CIRCUIT BREAKER TO VACUUM SWITCH 1 3 1393271
More informationTorque settings Torque settings. Frame torque settings. Note
3 - Torque settings Frame torque settings Part Thread (mm) Nm ±10% Tolerance Side stand Stand sensor screw M6x1 5 LOCK 2 Stand plate fixing screw M10x1.5 43 LOCK 2 Side stand fastening pin M8x1.25 Side
More informationServicing front brakes
46-1 Servicing front brakes C54 brake caliper, servicing Special tools and workshop equipment required VAG 1331 Torque wrench (or equivalent) VAG 1410 Torque wrench (or equivalent) VAG 1869/2 Brake pedal
More information