FRONT & REAR LOCK OPERATION & MAINTENANCE MANUAL

Transcription

1 Ram-Tilt Coupler Imagery does not reflect actual product size FRONT & REAR LOCK OPERATION & MAINTENANCE MANUAL 1

2 CONTENTS INTRODUCTION Owner Information 3 Warranty Registration 4 Key Features 5 Ram-Tilt Coupler Operation 6 To The Owner 7 SAFETY Safety Instructions 8 Safety Decals 9 Safety Identification Labels 10 W.L.L Working Load Limit 12 Safety Standards 14 Pre-start Check List 16 INSTALLATION PROCEDURE Installation 18 Plumbing Overview 19 Plumbing Circuit Diagram 20 Hydraulic Requirements & Plumbing 22 Smart Valve Installation 23 Operating & Attaching 24 Checking Attachments 26 MAINTENANCE General Maintenance 27 Cylinder Mount Nut Tightening Procedure 28 Daily Greasing 29 Suggested Greasing Products Hour Preventative Maintenance 31 Latch Inspections 33 Lifting Eye Inspection 35 Shackle Table 36 Maintenance & Repair Log 37 Parts Diagram 38 2

3 INTRODUCTION OWNER INFORMATION Thanks for choosing from JB Attachments range of Earthmoving products with the purchase of your new Ram-Tilt Coupler. This manual contains important information about the installation, maintenance and safe operation of the JB Ram-Tilt Coupler. You can assist in this proactive safety approach by ensuring that all persons involved with the fitting and operation of the Ram-Tilt Coupler, read and understand these basic safety features and instructions. JB reserves the right of modification as a result of further technical developments with regard to the information and illustrations cited in this manual JB and its suppliers have sole copyright of this manual The manual is intended solely for the use of the JB Ram-Tilt Coupler No part of this manual may be reprinted, translated or reproduced by any means without prior written permission from JB Attachments Utilisation for the purposes of competition is forbidden The JB Ram Tilt is designed for safe and dependable service if installed, maintained and operated correctly We request that time be devoted to the study of installation and maintenance requirements. Users are also expected to familiarise themselves with the correct operation and use of the Ram-Tilt Coupler and its advised safety procedures. IMPORTANT NOTE: To comply with Occupational Safety and Health requirements, a record must be made of all repairs, adjustments and regular maintenance events involving your Ram-Tilt Coupler. A Maintenance & Repair Log has been placed at the back of this manual for this purpose, please refer to page 38. 3

4 INTRODUCTION WARRANTY REGISTRATION Upon delivery of your JB Ram-Tilt Coupler please complete and return this form immediately to your local JB Attachments office. DATE OF DELIVERY: SERIAL NUMBER: I confirm that the operator of the relevant excavator has read and understands the Operating Instructions and Warranty Terms, which relate to JB Ram-Tilt Coupler. The Operator accepts that he/she is responsible for understanding safety and operation features of the JB Ram-Tilt Coupler. NAME: POSITlON: COMPANY: SIGNATURE: THE PURCHASER SHALL: Follow the recommended installation, testing and maintenance and operating procedures Comply with safety and training guidelines for use of equipment (not totally exclusive) Keep an accurate maintenance, operation, malfunction and repair log of equipment Ensure that the equipment is used for the purpose it was intended for 4

5 INTRODUCTION KEY FEATURES Hard Pins all around for excellent load bearing and wear resistance JB Smart Valve protects Ram-Tilt Coupler from high pressure spikes, allowing for precise control & improves holding force Low Profile results in maximisation of break out force, improved fuel economy and less strain on your machine Twin Displacement Cylinders Proven, simple robust design Individually Certified & Tested (CPENG) with full manufacturing record Compliant Front & Rear Locking slide to AS4772:2008 & ISO 13031: 2016 Integral pivot tube adds to pivoting mechanism strength 90 Degree Tilt allows tilting of Attachments 45 degrees each way, adding versatility to your attachments and your work environment 5

6 INTRODUCTION RAM-TILT COUPLER OPERATION The patented JB Multi-Coupler system allows your Ram-Tilt Coupler to pick up a range of attachment pin centres with the same pin diameter.* The JB Multi Coupler contains a fully compliant Front & Rear locking mechanism. * Contact JB for pickup range Phase 1: With the slide fully extended, the front safety latch is open to pick up the front pin of attachment. Phase 2: Retracting the slide fully engages the front safety latch onto the front pin of attachment and the rear safety latch becomes open. Phase 3: With the rear pin of the attachment in contact with the coupler, fully extending the slide wedges the slide onto the rear pin and engages the rear safety latch. Oil is locked in the cylinder by the check valve. RAM-TILT COUPLER OPERATING PRINCIPLE The single acting displacement cylinder design incorporates smart valve technology which locks the position of the tilt hitch once it is at the required angle. Hydraulic oil is trapped in both cylinders and is only released should the external load on the hitch be greater than the safe operating pressure of the cylinder. Urethane absorbers at the base of each cylinder allow them to move through the tilting range. The urethane also absorbs any shock loading that the JB Ram-Tilt is subjected to, aiding its robust design. Ram-Tilt Coupler at horizontal position Ram Tilt at 45 degrees position 6

7 INTRODUCTION TO THE OWNER As the new owner and/or operator of the JB Ram-Tilt Coupler we would recommend that you take the time to read this Operation Manual carefully before commencing work. FOLLOW THE SAFETY INSTRUCTIONS: Carefully read all the safety information contained in this manual Make sure all warning signs are securely fitted, refer to pages 9 & 13 Immediately replace any signs which are missing or damaged Before starting work make sure you are familiar with the equipment, and where necessary with the machine and its control devices INFORMATION FOR THE USER: The user of the JB Attachments Ram-Tilt Coupler is obliged to ensure that the equipment is always in safe working order in accordance with accident prevention regulations, Occupational Safety and Health or any other official instructions. WARRANTY REGULATION: JB Attachments provides guarantees according to its sales and delivery conditions, extended to twelve months from delivery. The extended guarantee assumes proper operation and use as intended but will be nullified as a result of: Repairs or other intervention not undertaken by persons authorised by JB Attachments With use of accessories or replacement parts not approved by JB Attachments or which are not original replacement parts supplied by JB Attachments After the warranty period has expired, we further recommend the use of original replacement parts and manufacturer s replacement parts approved by JB Attachments. 7

8 SAFETY SAFETY INSTRUCTIONS This safety alert symbol indicates important safety messages in this manual. When you see this symbol carefully read the message that follows and be alerted to the possibility of personal injury or death. WARNING: Incorrect operation of this machine can cause injury or death. Before using this machine make sure that every operator: Is instructed in safe and proper use of the attachment Reads and understands the manual pertaining to the attachment Reads and understands all safety decals and tags on the machine Clears the area of all other persons Learns and practises safely using attachment controls in a safe, clear area before operating this machine on a job site It is your responsibility to observe pertinent laws and regulations and follow JB Attachments instructions for operation and maintenance. JB Attachments supplies a standard JB Ram-Tilt Coupler to fit JB Attachments approved Attachments. However, when fitting a non standard attachment check the operation fitting guide for the attachment s pin range and width to suit the JB Ram-Tilt Coupler. NOTE: The JB Ram-Tilt Coupler base has a maximum and minimum pin center travel range. Please refer to the attached badge on the JB Ram-Tilt Coupler for this information. 8

9 SAFETY SAFETY DECALS The JB Attachments Multi-Coupler operation instructions are to be fitted inside the cab in clear view of the operator to identify correct operation of our Attachments. 9

10 SAFETY SAFETY IDENTIFICATION LABELS The pin centre range displays the minimum and maximum travel distance for each slide hook on the Ram-Tilt Coupler. All Attachments must be within the parameters of these measurements identified on the label. The label also identifies the slide hook type. W.L.L The badge also displays the W.L.L and data information. Note: The W.L.L is also stamped on the Lifting Eye. All JB Ram Tilts have an identification label with the machine & model recorded. JB RAM-TILT COUPLER SAFE OPERATION 10

11 SAFETY Each JB Ram-Tilt Coupler will have numerous identification labels fitted as shown below: The slide has numbering to identify the type, model, pin size & grab range The hydraulic cylinder has a serial number stamped to identify its model for servicing 11

12 SAFETY W.L.L - WORKING LOAD LIMIT Your JB Ram-Tilt Coupler comes with an integrally designed Lifting Eye which has been individually pull tested & certified to meet and exceed current standards. W.L.L is both stamped on Ram-Tilt Coupler & pickup range tag Stamping shows unique certification number and the W.L.L e.g XXXX-XXX XXXXKG Lifting Eye 12

13 SAFETY The Certified Lifting Eye must be used accordingly to the following guidelines: Only use the Lifting Eye at the rear of the Ram-Tilt Coupler for lifting Do not lift with bucket or any other attachment fitted to the Ram-Tilt Coupler Ensure that the load to be lifted does not exceed the rated W.L.L of the Ram-Tilt Coupler & Lifting Eye The Lifting Eye is to be used with a certified lifting shackle with the same or greater safe working load Lifting must be carried out with the Ram-Tilt Coupler in a vertical position so that the load can hang free without contacting the Ram-Tilt Coupler body Lifting Eye must be visually inspected daily for defects and wear The below sticker MUST be permanently fixed to the operators cab in a clearly visible location 13

14 SAFETY SAFETY STANDARDS The standards and Occupational Safety and Health Guidelines for the JB Ram-Tilt Coupler are as follows: AS Standards Australia. Australian standard for - Earthmoving Machinery Multi- Couplers (couplers) for excavators and backhoe loaders - AS section C AS Cranes (Including hoists and winches) Part 5: Mobile vehicle loading cranes European Standard EN474-5; Section /2 and 3 ISO 13031: 2016 Earthmoving Machinery Standard Operating Guidelines for Plant and Machinery We request that time be devoted to the study of installation and maintenance requirements. Users are also expected to familiarise themselves with the correct operation and use of the Ram-Tilt Coupler and its advised safety procedures. ASSOCIATED STANDARDS: AS 2954 Earthmoving Equipment - Rated Loads and Volumetric ratings AS 2954 Earthmoving Equipment - Tests and Measurements AS 2954 Earthmoving Equipment - Instrumentation and Control AS 2954 Earthmoving Equipment - Operation and Maintenance AS 2954 Earthmoving Equipment - Safety 14

15 SAFETY Only the following competent persons may work independently with any of type of JB Earthmoving Attachments. Operators must possess the following: Over 18 years of age Highly competent Are physically and intellectually able Have been instructed in the general regulations concerning operational safety and particularly accident prevention Have been instructed in assembly, operation and maintenance of earth moving machinery and using the JB Ram-Tilt Coupler system. They must understand these operating instructions and have proven to the contractor that they are capable of operating such machinery Ensure that only authorised personnel work with the JB Ram-Tilt Coupler system NOTE: For JB Attachments products supplied to or manufactured in countries other than New Zealand and Australia, the rules for prevention of accidents and safely regulations for the respective country must be strictly adhered to. 15

16 SAFETY PRE-START CHECK LIST Location: Date: Ref no: Hazards Identified: Work Equipment Lifting Devices Ergonomics Entanglement Crushing Access / egress Slip, trip and fall Plant Movement Warning Devices on Equipment Noise Vibration Fumes Environmental People Affected YES NO N/A Involved in activity Close to activity Everyone on site Members of the Public Expected Precautions YES NO N/A Has the operator been adequately trained on the use of the Ram-Tilt Coupler in general? Is the operator competent in using the specific attachment on the machine? Is there a system for checking that the attachment pins are in place on the Ram-Tilt Coupler prior to work start everytime a different attachment is fitted? Is the operator aware that they must not operate the machine unless they are satisfied that the Ram-Tilt Coupler is secured in place? Does the view of the operator from inside the Cab allow them to visually see that the Ram-Tilt Coupler is secured in place? Does the Ram-Tilt Coupler have the approved labels stating and referring to attachment specifications? Is there a risk assessment for the bucket detachment? Is there a checklist of daily and weekly inspections? Is there cab instructions for the Ram-Tilt Coupler? Personal Protective Equipment (PPE) Hard Hat High Visibility Vest Safety Boots Gloves Ear Protection Safety Glasses Other Management Assessed By: Name: Date: Reported To: Name: Date 16

17 SAFETY Operator s Name: JB Attachments Hitch #: JB Attachments Model: Date: In Cab Ram Tilt Operating Controls (Alarm, warning light, switch) Operating Instructions (labels) Operating Manual M O N T U E W E D T H U F R I S A T S U N Hydraulic System Wear or damage to hoses or fittings Security of hoses Hydraulic oil leaks Ram-Tilt Coupler Damage to the Ram-Tilt Coupler latch Correct functioning of safety latch device, rear slide hook and cylinder Build up of dirt and debris from around safety latch Build up of dirt and debris from rear slide hook Wear on the attachment body and Lifting Eye Wear on slide hook Wear and damage to bucket / attachment pins and retainers Security of mounting pins, locking bolts and nuts Is the attachment safe to use? YES or NO Lubrication Greasing in accordance with JB s instructions Operator Signature Manager Signature 17

18 INSTALLATION PROCEDURE INSTALLATION Align JB Ram-Tilt Coupler to the rear link and insert the original hard pin. Fit shims and O-ring seals as required. CHECK PINS ARE ORIGINAL EQUIPMENT MANUFACTURERS PINS Align JB Ram-Tilt Coupler to the dipper arm and insert the original hard pin. Fit shims and O-Ring seals as required. Fit locking bolts and nuts to each pin to secure pins. 18

19 INSTALLATION PROCEDURE PLUMBING OVERVIEW JB recommends using a reversing manifold block mounted to the dipper arm for plumbing the Ram-Tilt Coupler to the machine. This should be carried out by a professional and experienced hydraulics installer. Hoses to machine Reversing Block Connecting hoses to Smart Valve Calibre Smart Valve WHEN PLUMBING RAM-TILT COUPLER TO MACHINE Disconnect battery prior to any welding. Failure to do so can result in damage to the machines electronics Protect hydraulic cylinder rods from weld spatter Check for tolerance between latch & machine Ensure that the connecting hoses will not be pinched or damaged through the entire crowd linkage movement 19

20 INSTALLATION PROCEDURE PLUMBING CIRCUIT DIAGRAM 20

21 INSTALLATION PROCEDURE ITEM DESCRIPTION COMMENTS 1 Oil Reservoir - 2 Pump Must have min 3000 PSI & 50LPM **DO NOT USE PILOT PUMP** 3 Check Valve - 4 Coupler Cylinder Control Valve Can be OEM supply or Hydraulics installer supply 5 Pressure reducing **Must set between PSI** catridge 6 Single Acting Solenoid - Control Valve 7 Connect Solenoid to - Coupler/Buzzer Alarm 8 Tilt Cylinder Control Valve Can be OEM supply Hydraulics or installer supply 9 Calibre Smart Valve JB Supply 10 Operational Flow See table for sizing Control Orifice 11 JB Tilt Cylinder - 12 Coupler Cylnder Manifold - 13 Pilot Operated Sun CKCB-XCN Check Valve 14 Coupler Cylinder - 21

22 INSTALLATION PROCEDURE HYDRAULIC REQUIREMENTS & PLUMBING COUPLER CIRCUIT REQUIREMENTS Operating Pressure Hose Size PSI 1/4 Maximum TILT CIRCUIT REQUIREMENTS JB Machine Tonnage Unit 6T 8T 14T 20T 35T 45T Rod Size mm Stroke mm Displacement L Rotation Time * S Suggested Oil Flow L/min Operating Pressure PSI Port Connections (JB Supplied) Circuit Relief Pressure Hose/Tube Size (Minimum) 7/16 JIC Male PSI * Full 90 degree rotation i.e. stop to stop /16 JIC Male /16 JIC Male /16 JIC Male /16 JIC Male /16 JIC Male Inch 1/4 1/4 1/4 1/4 1/4 1/4 22

23 INSTALLATION PROCEDURE SMART VALVE INSTALLATION Smart Valve: The connection hoses connect to the JB Smart Valve located on the Ram-Tilt Coupler as shown: Quick Hitch (to machine) Quick Hitch (to machine) Tilt Cylinder Valve (to machine) Tilt Cylinder Valve (to machine) Quick Hitch (to cylinder) Quick Hitch (to cylinder) Quick Hitch (to machine) 23

24 INSTALLATION PROCEDURE OPERATING & ATTACHING Following the installation of the JB Ram-Tilt Coupler onto the machine, consult with the hydraulic installer as to the correct control operation of the Multi-Coupler and tilting cylinder circuits. Depending on installer and the method used, controls can vary and it is important that the operator clearly understands how each circuit is operated Fully extend slide and ensure that front safety latch is fully open. Line up Attachment and engage front pin. Fully retract slide and ensure that front safety latch is engaged over front pin Crowd the Ram-Tilt Coupler into the Attachment so that the rear pin makes contact. Fully extend slide to lock onto rear pin. Check that both front and rear safety latches are engaged. To Release Attachment: 1. Place Attachment on flat ground 2. Retract slide and crowd out of rear pin 3. Extend slide to release front safety latch 4. Lift Ram-Tilt Coupler away from Attachment 24

25 INSTALLATION PROCEDURE WARNING! Check all Attachments are fitting correctly. The safety latch is designed to work in closed position on the front pin. If the safety latch is not closed when attached to any attachment, check the rear jaw on the Ram-Tilt Coupler is fitting. If uncertain DO NOT USE THIS ATTACHMENT - call your local JB Attachments dealer for assistance. Advise manufacturer of which attachment is not fitting and arrange modification before it is used. To ensure the Ram-Tilt Coupler has engaged securely to pins on Attachment: Visually check the safety latch is engaged on the pin Test before operating through applying pressure to Attachment by rotating against the ground and away from machine Do not proceed with work unless the safety latch is in closed position on the front pin If the safety latch on the front pin is open DO NOT OPERATE MACHINE SAFETY LATCHES IN CLOSED POSITION 25

26 INSTALLATION PROCEDURE CHECKING ATTACHMENTS WARNING: Check pin centres of JB Ram-Tilt Coupler for all Attachments Label will indicate pin center range minimum - maximum A) Check that each individual Attachment s pin-center fits the Ram-Tilt Coupler to confirm the range on the label B) Check the inner width of the Ram-Tilt Coupler. Width must be wider than the Ram-Tilt base Spacers can be fitted to either the base of the Ram-Tilt Coupler or between the inner side of the ears and the bosses of Attachment. It is especially advisable to fit spacers in the case of heavier applications, particularly on machines that are 14 ton and above. DANGER: DO NOT USE ANY ATTACHMENT WITH THE SAFETY LATCH UP 26

27 MAINTENANCE GENERAL MAINTENANCE DAILY CHECKS 1) Complete Ram-Tilt Coupler Pre-start Checklist - refer to pages ) Grease Ram-Tilt Coupler regularly - refer to page 29 It is important that all parts are greased 3) Check Lifting Eye for damage. If in doubt do not continue use - refer to page 35 4) Check dirt build up in rear safety latch WARNING - Maintenance Work Maintenance work must be completed by competent personnel or assistance from JB Attachments. WARNING - Ram-Tilt Coupler Condition A defective Ram-Tilt Coupler could injure you or others. Do not operate a Ram-Tilt Coupler if it is defective, please contact JB Attachments immediately. Replacement Parts We recommend that you fit genuine replacement parts. You will need to quote the Ram-Tilt Coupler serial number stamped on the Ram-Tilt Coupler. data plate when ordering replacement parts. Refer to page 37 for Parts Diagram information. 27

28 MAINTENANCE CYLINDER MOUNT NUT TIGHTENING PROCEDURE WHILE RAM-TILT COUPLER IS IN THE HORIZONTAL POSITION TIGHTEN NYLOCK NUTS ON BOTH CYLINDERS UNTIL THERE IS NO GAP BETWEEN NUT, STEEL WASHER, URETHANE WASHER & CYLINDER CAGE. ***DO NOT FORCIBLY TIGHTEN OR URETHANE WASHER WILL EXTRUDE*** WHEN HITCH IS TILTED IT IS CORRECT TO HAVE A LARGE GAP APPEAR BETWEEN NYLOCK NUT & WASHERS. DIMPLE ON PIN IDENTIFIES GREASE EXIT POINT MUST FACE UPWARDS OFFSET GREASE POINT ON PIN IDENTIFIES GREASE EXIT POINTS MUST FACE UPWARDS ATMOSPHERE GREASE FILLED VOID LIP SEAL INSTALLED BACK TO FRONT I.E. NUMBERING FACING INWARDS & LIP OUTWARDS. SO GREASE WILL BLOW SEAL OPEN & GREASE TO WASTE WHILE KEEPING DIRT OUT HARD PIN PIN HARD BUSH SECTION SHOWING TYPICAL PIN & HARD BUSH SEALING ARRANGEMENT 28

29 MAINTENANCE DAILY GREASING It is recommended that the JB Ram-Tilt Coupler is thoroughly greased ONCE DAILY for all 8 grease points OR every 2 hours if operating under water. This will help pro-long the service life of & help maintain smooth operation of the Attachment. Grease points shown are below. 1 2 & & 7 8 It is essential that this log is filled in at the time of carrying out maintenance or repair on the JB Ram-Tilt Coupler In the unfortunate event of an accident, this log may be vital evidence as to compliance with Occupational Safety and Health requirements Work carried out on this JB Ram-Tilt Coupler must only be by an authorised person 29

30 MAINTENANCE SUGGESTED GREASING PRODUCTS SUGGESTED REQUIREMENTS: NLGI Grade 2 Lithium Complex Base Better ones contain 3-5% Moly (MoS2/ Molybdenum Disulfide) additive Base Oil 40 degrees C exceeds 300 cst Exceeds 28kg on Timken OK load test Contains high tack/ adhesive qualities/ Resists water washout SUGGESTED PRODUCTS: Moreys BigFoot EP2 Moreys Moly Complex EP2 Moreys Super Red Premium Waterproof Cat Ultra 3Moly Grease NGI2 Trans Diesel Super Red Lith Tac EP2 Shell Gadus S3 V460D Mobil Grease XHP 462 Moly Any Mobil XHP 460 Grease Gulf Western Red Lith Tac GENERAL NOTE: Reccomended greases are generally hard to pump because of their high viscosity. A quality 10000psi gun will give guaranteed results. 30

31 MAINTENANCE 500 HOUR PREVENTATIVE MAINTENANCE VISUAL STRESS POINTS CHECK: Visually check the entire Ram Tilt, including the slide, for any cracks, damage and excessive wear. The image below highlights major stress areas which particular attention should be given during checks. Should you find any cracks, damage or excessive wear, contact JB Attachments immediately. Cage Ear to baseplate at front Lifting Eye Front jaw and safety latch region Hook region on slide Body where rear attachment pin interfaces 31

32 MAINTENANCE The slide hook will have free movement when new. To gauge the wear of the cast body and slide hook place an allen key as in image 1 to test the space between the slide hook and cast body. Please see the table below to verify the maximum wear of the cast body. GUIDELINE FOR MAXIMUM WEAR 6,8,14 T 5mm 20,35,45 T 7mm The slide should sit below the bearing surface of the rear attachment pin no less than 3mm The maximum permissible wear of the bearing surface where the rear pin wedges against is 3mm 3 3 If the Ram-Tilt Coupler body becomes worn or damaged in this area contact your local JB Attachments branch or authorised service centre immediately. 32

33 MAINTENANCE LATCH INSPECTIONS Manual Inspection of both the Front & Rear Latch is to be carried out to ensure safety latch movement is within acceptable safety tolerances as specified below. This is in addition to daily visual check of safety latch and usual wear-and-tear assessments. This Maximum Opening Distance should be compared to the Safe Allowable Variation Table. If the Maximum Opening Distance is LESS than the Maximum Allowable Opening Distance for the Multi-Coupler model, it is safe to use. FRONT LATCH Must fully RETRACT slide to lock safety latch Must LIFT UP latch & measure gap in between Use a ruler to measure the distance between the bottom of the jaw to the tip of the Safety Latch whilst pulled up with hand Maximum Opening Distance Safe Allowable Variation Table LIFT UP Model Attachment Pin Diameter (mm) Maximum Opening (mm) JB JB JB JB JB JB JB JB JB JB JB JB If the Maximum Opening Distance is greater than the Maximum Allowable Opening value for that JB Multi-Coupler model. Please contact JB Attachments service department for advice. 33

34 MAINTENANCE REAR LATCH Must fully EXTEND slide to lock safety latch Must PULL DOWN latch & measure gap in between Use a ruler to measure the distance between the bottom of the jaw to the tip of the safety latch whilst pulled up with hand Maximum Opening Distance Safe Allowable Variation Table Model Attachment Pin Diameter (mm) Maximum Opening (mm) JB JB JB JB JB JB JB JB JB JB JB

35 MAINTENANCE LIFTING EYE INSPECTION WARNING: The Lifting Eye requires visual inspection monthly. Model Minimum Lifting Eye Width (mm) A Minimum Lifting Eye Width (mm) B Minimum Distance to Edge (mm) C Maximum Lifting Eye Hole (mm) D JB JB JB JB JB JB Visual check for cracking or deformation 2. Check for wear on the above chart 3. Damage to outer surface (A, B, C, D) must be with in the tolerances in above chart 4. If the Lifting Eye has exceeded recommended ratings - immediately stop using Attachment Should you find any deformation & cracks anywhere on the Lifting Eye, please get in touch with JB Attachments immediately. 35

36 MAINTENANCE SHACKLE TABLE Model # W.L.L Pin Diameter Width Standard JB AS AS RR-C RR-C-271 JB AS AS RR-C RR-C-271 JB AS AS RR-C RR-C-271 JB AS AS RR-C-271 JB AS RR-C-271 JB RR-C

37 MAINTENANCE MAINTENANCE & REPAIR LOG DATE FAULT REPAIR BY WHOM 37

38 MAINTENANCE PARTS DIAGRAM 38

39 MAINTENANCE LATCH SAFETY 39

40 JB Attachments Australia 59 Magnesium Drive, Crestmead, Australia 4132 Ph: Web: JB Attachments New Zealand 49 McLaughlins Road, Wiri, Auckland 2104 Ph: Web: 40