WORKING RANGE CHARTS TADANO MODEL TT-800XXL-4-80 TON CAPACITY. LIFTING CHARTS - Hydraulic Truck Cranes. Telescoping Mode II

Transcription

1 LFTNG CHARTS - Hydraulic Truck Cranes TADANO MODEL TT-8XXL-4-8 TON CAPACTY WORKNG RANGE CHARTS scoping Mode scoping Mode Lifting Height in feet Lifting Height in feet Load Radius from Axis of Rotation in Feet Load Radius from Axis of Rotation in Feet Boom Length in Feet (scoping Mode ) Boom Length in Feet (scoping Mode ) NOTE : 1.Boom and jib geometry shown are for unloaded condition and machine standing level on firm supporting surface. Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook. TT-8XXL-4 1

2 WEGHT REDUCTONS FOR AUXLARY LOAD HANDLNG EQUPMENT Load Handling Epuipment Main Hook Block(See Hook Block for actual weight) Aux.Hook(See Hook for actual weight)... (lbs.) (lbs.) #1 Lifting from Main Boom with Base and/or Jib stowed on base boom Singlestowedontopboom Single erected but not used 32.5'(9.9m)Base Jib erected but not used (lbs.) (lbs.) (lbs.) (lbs.) Boom Length 37.7' 51' 64.4' 91' 117.7' 131' 144.4' scoping Mode,, 2,1 14,1 13,3 8,5 8,1 6,5 6,6 5,1 4,8 4,8 32.5'(9.9m)Base Jib erected but not used +Aux.Hook on Jib Boom Length scoping Mode Boom Length scoping Mode 58.1'(17.7m)Base and Jib erected but not used +Aux.Hook on Jib Boom Length scoping Mode 25.6' Jib erected but not used 25.6' Jib stowed on 32.5'Base Jib (lbs.) 37.7' 51' 64.4' 91' 117.7' 131' 144.4',, 2,9 15, 14,3 9,5 8,8 7,2 7,3 5,8 5,4 5,4 (lbs.) 58.1'(17.7m)Base and Jib erected but not used 37.7' 51' 64.4' 91' 117.7' 131' 144.4',, 22,3 16,7 16,4 11,6 1,2 8,6 8,5 7, 6,3 6,2 (lbs.) 37.7' 51' 64.4' 91' 117.7' 131' 144.4',, 23,5 18, 18, 13,2 11,3 9,7 9,5 8, 7,2 6,9 Lifting from 32.5'(9.9m) Base Jib with Prohibited Prohibited Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 Fig.1 Fig.2 Fig.3 Fig.4 Fig.5 TT-8XXL-4 Note * Capacity deductions are for TADANO supplied epuipument only. * When liftiog from Jib,deduct total weight of all load handling devices reeved on Main Boom nose directly from Jib capacity. (#2) #1. Correct state of Jib, equipped or removed, should be inputted into the LOAD MOMENT NDCATOR(AML-L) by Jib state key switch. #2. The winch which is lifting load should be defined in the LOAD MOMENT NDCATOR(AML-L) by main winch/auxiliary winch selector switch. 2

3 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 15,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' 68 16, 74 13, , , 12' , , , , 15' 6 18, 68 13, , , 79 44, 79 3,8 2' 5 79, , , , 76 44, 76 3,8 8 3,8 8 17,6 25' 38 59, , 64 57, , 73 44, 73 3,8 77 3, , ,6 3' 21 43, , 58 4, , 69 39, 69 26,7 75 3, , , ,6 35' 39 31,4 53 3, ,,8 23, , , , ,6 4' 28 24, , , ,1 62 2,4 7 24,7 7 17, , ,6 45' 5 19,2 4 18,5 4 24, , , , ,4 7 17, ,6 5' 32 14,7 32 2, , , , , ,2 7 17,1 6' 46 12, , , , ,3 13,8 7' 36 8, ,4 52 9,8 52 9, ,1 61 1,5 8' 22 5,8 22 9, 46 7,1 46 8,4 52 8,6 56 7,7 9' 38 5, 38 7,2 46 6,4 51 5,7 1' 28 3,4 28 5,8 39 4,8 46 4,1 11' 13 2,2 13 4,5 31 3,6 39 2,8 12' 19 2,6 32 1,8 D o 19 o 32 o scoping conditions (%), 5 1 LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 15,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) B (35.87m) , , , , , ,2 11 2,2 11 4,5, A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) , ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED 15,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' , , , , 15' 6 9, , , , 79 44, 79 3,8 2' 5 52,4 62 5, , , 76 44, 76 3,8 8 3,8 8 17,6 25' 38, , , , ,7 73 3,8 77 3, , ,6 3' 21 23, , 58 21, , 69 24, , , 75 17, , ,6 35' 39 15, ,8 53 2,3 17,9 21, , , , ,6 4' 28 11, 47 1, , , ,1 7 14,9 7 17, , ,6 45' 5 7,8 4 7,1 4 12,2 59 1, , , ,3 7 13, ,3 5' 32 4,7 32 9,7 55 7, ,1 64 9, 64 11,7 68 1,6 7 9,7 6' 46 4, 46 7,3 59 5,4 59 8, 63 7, 6,1 7' 36 1,5 36 4,8 52 2,9 52 5,5 58 4,5 61 3,6 8' 22 3, 46 3,6 52 2,7 9' 38 2,2 D o 36 o o 52 o 38 o 52 o 61 o scoping conditions (%), , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, 15,7lbs COUNTERWEGHT, SPREAD 36 o ROTATON, FRONT JACK EXTENDED A 37.7' 51' 64.4' 64.4' 91' E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) , , , , ,4, TT-8XXL-4 A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) 3

4 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 7,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' , , , , 15' 6 15, , , , 79 44, 79 3,8 2' 5 77, , , , 76 44, 76 3,8 8 3,8 8 17,6 25' 38 51,7 55 5, , , 73 44, 73 3,8 77 3, , ,6 3' 21 36, , , , , ,7 75 3, , , ,6 35' 39 26, 53 25, ,5 28,8 23, , , , ,6 4' 28 19, , 47 24, ,4 62 2,4 7 23,9 7 17, , ,6 45' 5 15,3 4 14,6 4 2, , , , ,4 7 17, ,6 5' 32 11, , , , , , ,2 7 16,5 6' 46 9, ,9 59 1, , ,2 11,4 7' 36 6, 36 9,4 52 7,3 52 9,9 58 8,9 61 8,1 8' 22 3,6 22 6,9 46 4,9 46 7,4 52 6,4 56 5,6 9' 38 3,1 38 5,5 46 4,6 51 3,8 1' 28 1,7 28 4,1 39 3,1 46 2,4 11' 13 3, 31 2, D o 28 o o 31 o 46 o scoping conditions (%), , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, 7,7lbs COUNTERWEGHT, 36 o ROTATON, FRONT JACK EXTENDED A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) , , , , , ,1 11 3,, A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED 7,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' 65 17, , , , 15' 6 8, , , , 79 44, 79 3,8 2' 5 42, 62 4, , , 76 43,1 76 3,8 8 3,8 8 17,6 25' 38 26, , ,8 64 3, ,4 73 3, , , ,6 3' 21 17, , , , , ,8 75 2, , , ,6 35' 39 1,9 53 1, ,7 13,3 17, , , , ,6 4' 28 7,1 47 6, ,7 62 9, ,2 7 1,9 7 13, , ,7 45' 5 4,1 4 3,4 4 8,8 59 6,6 59 1,3 67 8, 67 1,9 7 9,8 72 8,8 5' 32 6,6 55 4,3 55 8,1 64 5,8 64 8,6 68 7,5 7 6,6 6' 46 4,8 59 5,4 63 4,3 7' 36 2,6 52 3,2 8' 46 1,6 D o 4 o o 55 o 36 o 64 o 46 o 63 o 7 o scoping conditions (%), , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, 7,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' E B (11.5m) B (15.56m) B (19.62m) , , ,, A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) TT-8XXL-4 4

5 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 3,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' , , , , 15' 6 13, , , , 79 44, 79 3,8 2' 5 74, ,2 69 7, , 76 44, 76 3,8 8 3,8 8 17,6 25' 38 47, , , , 73 44, 73 3,8 77 3, , ,6 3' 21, , 58 3, , , ,7 75 3, , , ,6 35' 39 23, , ,7 26,1 23, , , , ,6 4' 28 17, , ,6 62 2,2 62 2,4 7 21,6 7 17, , ,6 45' 5 13,4 4 12,6 4 18, , , , ,4 7 17, ,6 5' 32 9, , , , , 64 14, ,5 7 14,7 6' 46 7, ,4 59 9, ,8 63 1,7 9,9 7' 36 4,7 36 8,1 52 6, 52 8,6 58 7,5 61 6,7 8' 22 2,4 22 5,8 46 3,8 46 6,3 52 5,2 56 4,4 9' 38 4,5 46 3,6 1' 28 3,2 39 2,3 11' 13 2,2 D o 46 o o 39 o 56 o scoping conditions (%), , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, 3,7lbs COUNTERWEGHT, 36 o ROTATON, FRONT JACK EXTENDED A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) B (27.75m) B (35.87m) , , , , , , 11 2,2, A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED 3,7lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' 65 14, , , , 15' 6 71, ,5 73, , 79 44, 79 3,8 2' 5 36, ,1 69, , ,9 76 3,8 8 3,8 8 17,6 25' 38 22, ,3 64 2, , , , , , ,6 3' 21 14, , , , ,9 69 2, 75 17, , , ,6 35' 39 8,3 53 7, ,3 1,8 14, , , , ,3 4' 28 4,7 47 4, 47 9,6 62 7, ,1 7 8,7 7 11,8 73 1,5 74 9,5 45' 4 6,8 59 4,5 59 8,3 67 6, 67 8,9 7 7,8 72 6,8 5' 32 4,8 55 6,3 64 6,8 68 5,7 6' 46 3,3 59 3,9 7' 36 1,4 52 2, D o 47 o 32 o 59 o 36 o 67 o 52 o 68 o 72 o scoping conditions (%), , A 37.7' E B (11.5m) ,3, LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, 3,7lbs COUNTERWEGHT, 36 o ROTATON, FRONT JACK EXTENDED A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) TT-8XXL-4 5

6 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' , , , , 15' 6 1,9 68 1, , , 79 44, 79 3,8 2' 5 68,6 62, , , 76 44, 76 3,8 8 3,8 8 17,6 25' 38 43, ,7 64 4, , 73 44, 73 3,8 77 3, , ,6 3' 21 3, 48 28, , , , ,7 75 3, , , ,6 35' 39 2,8 53 2, 53 26,2 23,5 23, , , , ,6 4' 28 15, ,6 47 2, , 62 2,4 7 19,5 7 17, , ,6 45' 5 11,3 4 1,5 4 16, , , , ,4 7 17, 72 16,2 5' 32 7, ,1 55 1, , , , ,7 7 12,9 6' 46 6,3 46 9,9 59 7,6 59 1,3 63 9,2 8,4 7' 36 3,4 36 6,8 52 4,7 52 7,3 58 6,2 61 5,4 8' 22 4,7 46 5,2 52 4,2 9' 38 3,6 46 2,6 1' 28 2,4 11' 13 1,4 D o 36 o o 52 o 13 o 46 o 61 o scoping conditions (%), , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, lbs COUNTERWEGHT, 36 o ROTATON, FRONT JACK EXTENDED A 37.7' 51' 64.4' 64.4' 91' E B (11.5m) B (15.56m) B (19.62m) B (19.62m) B (27.75m) , , , , ,, A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED lbs COUNTERWEGHT, 36 o ROTATON A 37.7' 51' 64.4' 64.4' 91' 91' 117.7' 117.7' 131' 144.4' B C (11.5m) C (15.56m) C (19.62m) C (19.62m) C (27.75m) C (27.75m) C (35.87m) C (35.87m) C (39.93m) C (44.m) 1' , , , , 12' 65 12, , , , 15' 6 63,1 68 6, , , 79 44, 79 3,8 2' 5 32,1 62 3, , 69 36,4 76,1 76 3,8 8 3,8 8 17,6 25' 38 19, , , ,2 73 2, , , , ,6 3' 21 11,6 48 1,5 58 9, , , , , , , ,8 35' 39 5,6 53 4,7 53 1,8 8,1 12,3 72 9, , 75 11,7 76 1,7 4' 28 2,4 47 7,4 62 4,9 62 8,9 7 6,4 7 9,5 73 8,3 74 7,3 45' 4 4,9 59 6,4 67 7, 7 5,9 5' 32 3,1 55 4,6 64 5,2 6' 46 2, 59 2,6 D o 28 o 53 o 32 o 62 o 46 o 7 o 59 o 7 o 74 o scoping conditions (%), , A 37.7' E B (11.5m) ,4, LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, lbs COUNTERWEGHT, 36 o ROTATON, FRONT JACK EXTENDED A: Boom length in feet C: Loaded boom angle ( o ) E: Boom angle ( o ) B: Load radius in feet D: Minimum boom angle ( o ) for indicated length (no load) TT-8XXL-4 6

7 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MN EXTENDED 6' 9-7/8'' (2.8m) SPREAD, 36 o ROTATON, FRONT JACK EXTENDED Load Radius 37.7' (11.5m) Boom Counterweight in pounds in 15,7 7,7 3,7 Feet C C C C 1' 68 57, , , ,1 12' 65 41,5 65 3, , ,5 15' 6 27,5 6 19,2 6 15, 6 11,2 2' 5 15,4 5 9,6 5 6,7 5 4, 25' 38 8,9 38 4,4 38 2,2 3' 21 4,9 D o 38 o / o * 38 o / o * 5 o / o * scoping conditions (%),,,, C: Loaded boom angle ( o ) D: Minimum boom angle ( o ) for indicated length (no load) *: When Working Area is only Over Front and Over Rear. LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MN EXTENDED 6' 9-7/8'' (2.8m) SPREAD, FRONT JACK EXTENDED 36 o Rotation Over Front and Over Rear 37.7' (11.5m) Boom Boom Counterweight in pounds Angle 15,7 7,7 3,7 B B B B o , , , ,2,,,, B: Load radius in feet NOTE: - The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-L) is based on the standard number of parts of line listed in the chart. - Standard number of parts of line for each boom length should be according to the following table. Boom Length in Feet 37.7' 37.7' to 51' 51' to 64.4' 64.4' to 91' 91' to 144.4' Single top (meters) (11.5) (11.5 to 15.56) (15.56 to 19.62) (19.62 to 27.75) (27.75 to 44.) Jib Number of parts of line TT-8XXL-4 7

8 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 15,7lbs COUNTERWEGHT, 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib 25 o 3.5 o Tilt Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o.6 9, , ,1 8 o 4.6 5, , ,4 75 o 5.5 9, , ,3 75 o 6.6 5, , ,4 7 o. 9, , ,6 7 o , , ,4 65 o 8.1 7, , , 65 o , , ,1 6 o , , ,1 6 o , , ,9 55 o 15. 3, , ,6 55 o , , ,1 5 o , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o.2 6, ,7.9 3,7 75 o , 51. 1, , 75 o , , ,7 7 o , , ,4 7 o , , ,6 65 o.1 9, , ,7 65 o 8.2 6, , ,5 6 o , , ,2 6 o , , ,3 55 o 88. 6, , ,6 55 o 16. 4, , ,1 5 o 97. 4, , ,6 5 o , , ,9 45 o 16. 3, , ,5 45 o , , ,1 4 o , ,6 4 o , ,5 35 o , ,9 3 o , ,4 25 o 1. 1, 117.7' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 5.8 6, , ,7 7 o , , ,9 7 o.8 6, , ,6 65 o , , 8. 6,2 65 o 81. 5, , ,3 6 o , , ,7 6 o , , , 55 o , , ,2 55 o 16. 3, , ,8 5 o , 15. 4, ,5 5 o , , ,7 45 o 18. 4, , , 45 o , , ,5 4 o , ,6 4 o , ,3 35 o , ,3 35 o , , 3 o 13. 3,1 1. 3, 3 o , ,8 25 o , ,7 25 o , ,6 R: Load radius in feet W: Rated lifting capacity in pounds ON OUTRGGERS MD EXTENDED 15' 9'' (4.8m) SPREAD, FRONT JACK EXTENDED 15,7lbs COUNTERWEGHT, 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o.6 9, , ,1 8 o 4.6 5, , ,4 75 o , , ,1 75 o 6. 5, , ,4 7 o , , ,2 7 o , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o 45 o Tilt Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o.2 6, ,7.9 3,7 75 o , 51. 1, , 75 o , , ,7 7 o , , ,8 7 o , , ,6 65 o , , ,3 65 o , 95. 2, ,4 6 o , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 5.8 6, , ,7 7 o , , ,9 7 o.8 6, , ,6 65 o.1 6, , ,7 65 o 8. 4, , ,3 6 o , , , 6 o 92. 2, , ,3 55 o , , ,8 55 o 13. 1, , ,4 5 o , 13. 1, ,8 R: Load radius in feet 45 o 14. 1, , ,1 W: Rated lifting capacity in pounds TT-8XXL-4 8

9 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 7,7lbs COUNTERWEGHT, 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o.6 9, , ,1 8 o 4.6 5, , ,4 75 o 5.5 9, , ,3 75 o 6.6 5, , ,4 7 o , , ,6 7 o , , ,4 65 o , , ,4 65 o , , ,1 6 o , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o.2 6, ,7.9 3,7 75 o , 51. 1, , 75 o , , ,7 7 o , , ,4 7 o , , ,6 65 o.1 9, , ,7 65 o 8.2 6, , ,5 6 o , , , 6 o , , ,3 55 o , , ,3 55 o 14. 2, , ,5 5 o 96. 3, , 16. 3, 45 o 15. 2, , , 117.7' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 5.8 6, , ,7 7 o , , ,9 7 o.8 6, , ,6 65 o , , 8. 6,2 65 o 81. 5, , ,3 6 o , , ,7 6 o , , , 55 o , , ,2 55 o 16. 3, , ,8 5 o , 15. 4, ,5 5 o , , ,7 45 o 17. 3, , ,7 45 o , , ,2 4 o , 12. 2,9 4 o , ,7 35 o , ,3 35 o , ,2 3 o , ,8 R: Load radius in feet 25 o , ,5 W: Rated lifting capacity in pounds TT-8XXL-4 ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED 3,7lbs COUNTERWEGHT, 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o.6 9, , ,1 8 o 4.6 5, , ,4 75 o 5.5 9, , ,3 75 o 6.6 5, , ,4 7 o , , ,6 7 o 78. 5, , ,4 65 o , , ,4 6 o , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o.2 6, ,7.9 3,7 75 o , 51. 1, , 75 o , , ,7 7 o , , ,4 7 o , , ,6 65 o , , ,7 65 o 8. 5, , ,5 6 o , , ,9 6 o , , ,9 55 o , , ,4 5 o , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt 8 o , , ,3 8 o , , ,7 75 o , , ,7 75 o 5.8 6, , ,7 7 o , , ,9 7 o.8 6, , ,6 65 o , , 8. 6,2 65 o 81. 5, , ,3 6 o , , ,7 6 o , , , 55 o , , ,9 55 o 16. 3, , ,8 5 o , , ,8 5 o , , ,2 45 o 16. 3, , ,9 45 o , , ,6 4 o , ,1 4 o ,1 35 o , ,6 R: Load radius in feet 3 o , ,2 W: Rated lifting capacity in pounds 9

10 TT-8XXL RATED LFTNG CAPACTES (N POUNDS) 8 o 75 o 7 o 65 o 8 o 75 o 7 o 65 o 6 o 55 o 8 o 75 o 7 o 65 o 6 o 55 o 5 o 45 o 4 o ON OUTRGGERS FULLY EXTENDED 23' 7-1/2'' (7.2m) SPREAD, FRONT JACK EXTENDED lbs COUNTERWEGHT, 36 o ROTATON 144.4' (44.m) Boom ' (9.9m) Jib 144.4' (44.m) Boom ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt.6 9, , ,1 8 o 4.6 5, , , , , ,3 75 o 6.6 5, , , , , ,8 7 o , , , , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 45 o 3.5 o Tilt 25 o Tilt Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt , , ,3 8 o.2 6, ,7.9 3, , 51. 1, , 75 o , , , , , ,4 7 o , , , , , , 65 o , , 14. 3, , , , 6 o 9.7 2, , , , , ' (35.87m) Boom (telescoping ) ' (9.9m) Jib 117.7' (35.87m) Boom (telescoping ) ' (17.7m) Jib 3.5 o Tilt 25 o Tilt 45 o Tilt 3.5 o Tilt 25 o Tilt 45 o Tilt , , ,3 8 o , , , , , ,7 75 o 5.8 6, , , , , ,9 7 o.8 6, , , , , 8. 6,2 65 o 81. 5, , , , , ,5 6 o , , , , , ,1 55 o 15. 2, , , , , 15. 3, 5 o , , , , , ,2 R: Load radius in feet , ,5 W: Rated lifting capacity in pounds WARNNG AND OPERATNG NSTRUCTONS FOR LFTNG CAPACTES GENERAL OPERATON 1. RATED LFTNG CAPACTES apply only to the machine as 1. Rated lifting capacities have been tested to and meet minimum originally manufactured and normally equipped by TADANO LTD. requirements of SAE J163-Cantilevered Boom Crane Modifications to the machine or use of optional equipment Structures Method of Test. other than that specified can result in a reduction of capacity. 2. Rated lifting capacities do not exceed 85% of the tipping load 2. Hydraulic cranes can be hazardous if improperly operated on outriggers fully extended as determined by SAE J765-Crane or maintained. Operation and maintenance of this machine must Stability Test Code. be in compliance with information in the Operation and Rated lifting capacities for partially extended outriggers are Maintenance Manual supplied with crane. f this manual determined by this formula, Rated Lifting Capacities is missing, order a replacement through the distributor. =(Tipping Load -.1 x Tip Reaction)/ The operator and other personnel associated with this machine 3. Rated lifting capacities above bold lines in the chart are based shall fully acquaint themselves with the latest American National on crane strength and those below, on its stability. They are American National Standards nstitute (ANS) safety standards based on actual load radius increased by boom deflection. for cranes. 4. The weight of handling device such as hook blocks, slings, etc., must be considered as part of the load and must be SET UP deducted from the lifting capacities. 1. Rated lifting capacities on the load chart are the maximum 5. Rated lifting capacities are based on freely suspended loads allowable crane capacities. They are based on the machine and make no allowance for such factors as the effect of wind, standing level on firm supporting surface under ideal job conditions. sudden stopping of loads, supporting surface conditions, Depending on the nature of the supporting surface, it may be operating speeds, side loads, etc. Side pull on the boom or jib is necessary to have structural supports under the outrigger extremely dangerous. floats to spread the loads to a larger surface. 6. Rated lifting capacities do not account for the effects of wind on 2. For outrigger operation, outriggers shall be properly extended a lifted load or boom. Rated lifting capacities and boom length shall with tires free of supporting surface before operating crane. be appropriately reduced, when wind velocity exceeds 2 mph The front jack must be properly extended. (9 m/sec.). 3. When operating crane on outriggers fully retracted, do not 7. Rated lifting capacities at load radius shall not be exceeded. exceed 71 o maximum boom angle. Loss of backward stability Do not tip the crane to determine allowable loads. will occur causing a backward tipping condition. 8. Do not operate at boom lengths, radii, or boom angle, where no capacities are shown. Crane may overturn without any load on the hook. TT-8XXL-4 1

11 9. When boom length is between values listed, refer to the rated 2. For boom length less than 144.4' (44.m) and longer than lifting capacities of the next longer and next shorter booms for 117.7' (35.87m) with jib, rated lifting capacities are determined the same radius. The lesser of the two rated liftingcapacities by loaded boom angle only in the column headed "144.4' shall be used. (44.m) boom + jib". 1. When making lifts at a load radius not shown, use the next For boom length less than 117.7' (35.87m) with jib, rated lifting longer radius to determine allowable capacity. capacities are determined by loaded boom angle only in the 11. Load per line should not exceed 11, lbs. (5,kg) for column headed "117.7' (35.87m) boom + jib". For angles not main winch and auxiliary winch. shown, use the next lower loaded boom angle to determine 12. Check the actual number of parts of line with LOAD MOMENT allowable capacity. NDCATOR (AML-L) before operation. Maximum lifting 21. When lifting a load by using jib (aux. winch) and boom (main capacity is restricted by the number of parts of line of LOAD winch) simultaneously, do the following: MOMENT NDCATOR (AML-L). Limited capacity is as Enter the operation status as jib operation, not as boom determined from the formula, Single line pull for main winch operation. (11, lbs.) x number of parts of line. Before starting operation, make sure that mass of load is 13. The boom angle before loading should be greater to account within rated lifting capacity for jib. for deflection. For rated lifting capacities, the loaded boom 22. Before telescoping the boom, set the telescoping angle and the load radius is for reference only. selector switch to MODE or MODE with the boom 14. The 37.7' (11.5m) boom length capacities are based on boom fully retracted. A change of the telescoping is not fully retracted. f not fully retracted [less than 51'(15.56m) permissible when the boom has been partially or fully extended. boom length], use the rated lifting capacities for the 51' (15.56m) boom length. DEFNTONS 15. Extension or retraction of the boom with loads may be 1. Load Radius: Horizontal distance from a projection of the axis attempted within the limits of the RATED LFTNG CAPACTES. of rotation to supporting surface before loading to the center of The ability to telescope loads is limited by hydraulic pressure, the vertical hoist line or tackle with load applied. boom angle, boom length, crane maintenance, etc. 2. Loaded : The angle between the boom base 16. For lifting capacity of single top, reduce the rated lifting section and the horizontal, after lifting the rated lifting capacity capacities of relevant boom according to a weight reductions at the load radius. for auxiliary load handling equipment. Capacities of single top 3. Working Area: Area measured in a circular arc about the shall not exceed 11, lbs. (5,kg) including main hook. centerline of rotation. 17. When base jib or top jib or both jib removing, jib state switch 4. Freely Suspended Load: Load hanging free with no direct select removed. external force applied except by the hoist line. 18. When erecting and stowing jib, be sure to retain it by hand or by 5. Side Load: Horizontal side force applied to the lifted load either other means to prevent its free movement. on the ground or in the air. 19. Use "ANT-TWO BLOCK" disable switch when erecting and stowing jib and when stowing hook block. While the switch is pushed, the hoist does not stop, even when overwind condition occurs. WARNNG AND OPERATNG NSTRUCTONS FOR USNG THE LOAD MOMENT NDCATOR (AML-L) 1. When operating crane on outriggers: 4. The displayed values of LOAD MOMENT NDCATOR Set Stater switch to "ON" position. (AML-L) are based on freely suspended loads and make no Press the outrigger select key to register the allowance for such factors as the effect of wind, sudden outriggers condition with the LOAD MOMENT NDCATOR stopping of loads, supporting surface conditions, operating (AML-L). Press the register key. The outrigger status speed, side loads, etc. For safe operation, it is recommended symbol will change from flashing to a solid light. that lifted loads be appropriately reduced when extending Press the lift select key to select the lift and lowering the boom or swinging. status that corresponds to the actual boom configuration. 5. LOAD MOMENT NDCATOR (AML-L) is intended as an aid Each time the lift select key is pressed, the to the operator. Under no condition should it be relied upon status changes. Press the register key to register the to replace use of capacity charts and operating instructions. lift status with the LOAD MOMENT NDCATOR Relying solely upon the LOAD MOMENT NDCATOR (AML-L). The lift status symbol will change from (AML-L) in place of good operating practice can cause an flashing to a solid light. accident. The operator must exercise caution to assure When mounting and stowing the jib, select the jib set safety. status. (The jib state symbol will be flashing.) 2. The swing does not automatically stop if the crane become overloaded. 3. During crane operation, make sure that displays on the front panel of the LOAD MOMENT NDCATOR(AML-L) are in accordance with actual operating conditions. TT-8XXL-4 11

12 TT-8XXL Axle weight distribution chart Pounds Kilograms GVW Front Rear GVW Front Rear Base machine with 15.7gal.(4L)fuel and spare tire no counterweight 89,25 42,15 47,1 4,485 19,122 21,363 Remove 1. Auxiliary hoist with 436' (1m) of 3/4" (19mm) -1, , , ton (5. metric ton) hook ball jib (25.6') Base jib (32.5') -1,92-2, Auxiliary lifting sheave Spare tire Add: 1. Counterweight 3,7lbs on upper 3,7-1,75 5,45 1, , Counterweight 3,7lbs + 4,lbs on upper 7,7-3,64 11,34 3,495-1,651 5, Counterweight 3,7lbs + 4,lbs + 8,lbs on upper 15,7-7,42 23,12 7,125-3,3 1, Counterweight 3,7lbs to carrier deck 3,7 2, ,68 1, Counterweight 3,7lbs + 4lbs to carrier deck 7,7 5,72 1,98 3,495 2, Counterweight 8,lbs to carrier deck 8, 5,95 2,5 3,63 2, Counterweight 3,7lbs on upper + 4,lbs to carrier 7,7 1,22 6,48 3, ,94 deck 8. Counterweight 3,7lbs + 4,lbs on upper + 8,lbs 15,7 2,3 13,4 7,125 1,46 6,79 to carrier deck Option: 1. Hot water cab heater and air conditioning in upper cab TT-8XXL-4 12

13 CRANE SPECFCATONS BOOM DRUM - Grooved 15-3/4"(.4m) root diameter x 22-3/4" Five section full power synchronized telescoping boom, (.578m) wide. Wire rope: 436' of 3/4"diameter rope (1m of 37' 8-11/16"~144' 4-1/4"(11.5m~44m), of round hexagonal box 19mm). Drum capacity: 1,96' (4m) 7 layers. Maximum line construction with 7-sheaves, 17-5/16" (.44m) root diameter, at pull (permissible): 15,2lbs. (6,88kg)*. Maximum line speed: boom head. The synchronization system consists of two double 585FPM (178m/min). acting telescope cylinders, two extension cables and retraction cable. Hydraulic cylinder fitted with holding valve. Two easily WRE ROPE - Warrington seal wire, extra improved plow steel, removable wire rope guards, rope dead end provided on both preformed, independent wire rope core, right regular lay. sides of boom head. 3/4"(19 mm) 6X37 class Boom telescope sections are supported by wear pads both vertically and horizontally. Two boom telescoping s available. HOOK BLOCKS Extension speed 16' 7-1/2" in 145 seconds. 5.5 ton (5. metric ton) - Weighted hook with swivel and safety latch, for 3/4"(19mm) wire rope. BOOM ELEVATON - By a double acting hydraulic cylinder with holding valve. Elevation -2 o ~8 o, combination controls for HYDRAULC SYSTEM hand or foot operation. Boom angle indicator. Automatic speed reduction and soft stop function. PUMPS - Two variable piston pumps for crane functions. Elevation speed -2 o ~8 o in 77 seconds. Tandem gear pump for swing and optional equipment. Powered by carrier engine. Pump disconnect for crane is JB - Two stage bi-fold lattice type with 3.5 o, 25 o or 45 o offset engaged/ disengaged by rocker switch from carrier cab. (tilt type). Single sheave, 15-5/8"(.396m) root diameter, at the head of both jib sections. Stored alongside base boom section. CONTROL VALVES - Multiple valves actuated by pilot Jib length is 32.5' (9.9m) or 58.1' (17.7m). Assist cylinders for pressure with integral pressure relief valves. mounting and stowing are controlled at right side of superstructure. Self stowing jib mounting pins. RESERVOR gallon (7 lit.) capacity. External sight level gauge. AUXLARY LFTNG SHEAVE (SNGLE TOP) Single sheave, 15-5/8"(.396m) root diameter. Mounted to main FLTRATON - 26 micron return filter, full flow with bypass boom head for single line work (stowable). protection, located inside of hydraulic reservoir. Accessible for easy replacement. ANT-TWO BLOCK - Pendant type over-winding cut out device with audio-visual (FALURE lamp/buzzer) warning OL COOLER - Air cooled fan type. system. COUNTERWEGHT SWNG Hydraulically assembled/disassembled counterweight pinned Hydraulic axial piston motor driven through planetary swing to superstructure frame. speed reducer. Continuous 36 o full circle swing on ball bearing Three piece : 3,7lbs. (1,678kg) turntable at 1.7rpm. Equipped with manually locked/released 4,lbs. (1,814kg) swing brake. 36 o positive swing lock. Twin swing System: Free 8,lbs. (3,628kg) swing or lock swing controlled by selector switch on front console. Automatic speed reduction and soft stop function. CAB AND CONTROLS HOST MAN HOST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of main hoist. Equipped with cable follower and drum rotation indicator. DRUM - Grooved 15-3/4"(.4m) root diameter x 22-3/4" (.578m) wide. Wire rope: 797' of 3/4"diameter rope (243m of 19mm). Drum capacity: 1,96' (4m) 7 layers. Maximum line pull (permissible): 15,2lbs. (6,88kg)*. Maximum line speed: 585FPM (178m/min). AUXLARY HOST - Variable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of main hoist. Equipped with cable follower and drum rotation indicator. Left side, 1 man type, steel construction with sliding door access and tinted safety glass windows opening at side. Door window is powered control. Windshield glass and roof window glass are shatter-resistant. Adjustable control lever stands for swing, boom hoist, boom telescoping, auxiliary hoist and main hoist. Control lever stands can change neutral positions and tilt for easy access into cab. 3 way adjustable operator's seat with high back, headrest and armrest. Engine throttle knob. Foot operated controls: boom hoist, boom telescoping and engine throttle. Each outrigger beam and jack is controlled independently. Hot water cab heater and air conditioning (OPTONAL). Dash-mounted engine start/stop, monitor lamps, cigarette lighter, ashtray, telescoping / switch, boom telescoping/ auxiliary hoist control selector switch, low noise switch, windshield washer and wiper switch, power window switch, swing brake switch, telescoping / auxiliary winch select switch, swing stop cancel switch, slow elevation stop cancel switch and free swing / lock swing selector switch. nstruments - Hydraulic oil pressure is monitored and displayed on the AML-L display panel. TT-8XXL-4 13

14 Tadano electronic LOAD MOMENT NDCATOR system (AML-L) including: Control lever lockout function with audible and visual pre-warning. Boom position indicator Outrigger state indicator Boom angle / boom length / jib offset angle / load radius / rated lifting capacities / actual loads read out Ratio of actual load moment to rated load moment indication Automatic Speed Reduction and Soft Stop function on boom elevation and swing (swing range restricted only) Working condition register switch Load radius / boom angle / tip height / swing range preset function External warning lamp CARRER SPECFCATONS MANUFACTURER / MODEL - FAUN GmbH / KF7-4 TYPE - Left hand steering, 8x4 FRAME - High tensile steel, all welded mono-box construction. TADANO AML-L monitors outrigger extended length and automatically programs the corresponding "RATED LFTNG CAPACTES" table. boom emergency /,,top boom emergency telescoping switch. Correct jib status select switch. Upper console includes working light switch, roof washer and wiper switch, oil cooler switch, emergency outrigger set up key switch and air conditioning control switch (optional). Swing lock lever. NOTE:Each crane motion speed is based on unladen conditions. BRAKE SYSTEMS - Service: Full air brakes with multi-protection valve and auto slack adjuster on all wheels. Dual air line system, internal expanding leading and trailing shoe type with Anti-lock Braking System (ABS). Parking / Emergency: Spring loaded brake on rear 4-wheels controlled by knob of spring brake valve. Auxiliary: Exhaust brake (JAKE BRAKE by Cummins) TRANSMSSON - ZF AS Tronic 12AS231 TRES - Front: 445/65R22.5 Single Rear: 315/8R22.5 Dual Automatically shifting transmission system with the possibility of Spare: 445/65R22.5 SingleX1 semi-automatic operation. 12 forward and 2 reverse speeds. OUTRGGERS - Four hydraulic, beam and jack outriggers. Gear Traveling speeds in mph (km/h) Vertical jack cylinders equipped with integral holding valve. Each 1st (-6.3) outrigger beam and jack is controlled independently from either 4.97 (8.) side of carrier. Beams extend to 23' 7-1/2" (7.2 m) center-line and 6.46 (1.4) retract to within 8' 6" (2.59 m) overall width. Equipped with four 8.32 (13.4) 1' 7-11/16" (.5m) dia. stowable plastic floats. Controls and sight 5th 1.5 (16.9) bubble located on both side of carrier. Three outrigger extension 6th (21.7) lengths are provided with corresponding "RATED LFTNG 7th (28.6) CAPACTES" for crane duty in confined areas. 8th (36.8) Min. extension 6' 9-7/8"(2.8m) center to center 9th (47.4) Mid. extension 15' 9"(4.8m) center to center 1th (6.8) Max. extension 23' 7-1/2"(7.2m) center to center 11th (77.2) 12th (99.) 1st Reveres 4.23 (6.8) FRONT JACK - A fifth hydraulically operated outrigger jack is Reveres 5.41 (8.7) mounted to the front carrier frame providing 36 o lifting capacities. Hydraulic cylinder equipped with integral holding valve and 1' 3-11/16" AXLES - Front: Full floating type, steering axles. (.4m) dia. steel float. Rear: Full floating type, driving axles with inter-wheel differential lock. CARRER CAB - One man full with cab of composite structure (steel sheet metal and fiberglass), windshield of laminated safety glass with STEERNG - Dual-circuit hydraulic and mechanical steering windshield wiper and washer, sliding side windows of hardened glass. of both front axles with hydraulic power booster. Emergency Driver seat adjustable and air-suspended with headrests and 3 point steering pump mounted on axle reduction gear. Tilt telescoping safety belts. 2 rear-view mirrors (electrically adjustable), 1 wide angle steering wheel. mirror and additional curb mirror, all mirrors heated. Engine dependent warm-water heater with defroster nozzles for windshield and cab floor. SUSPENSON - Front: Load sharing type with leaf springs. nstrumentation includes speedometer, tachograph, rpm counter with Rear: Solid mounted tandem with equalizer beam and torque rods. hour meter, fuel level gauge, air pressure gauge and engine warning lamp, oil pressure control lamp. ENGNE (EPA Tier 2) Model Cummins QSM11 Radiator Fin and tube core, thermostat controlled No. of cylinders 6 Fan, in.(mm) Hydraulic driven fan, 29.5 (75) dia. Combustion 4 cycle, turbo charged and inter cooled Starting 24 volt, 7.5 kw BoreXStroke, in.(mm) 4.9' X 5.8' (125X147) Charging 24 volt system, negative ground Displacement, cu. in (liters) (1.8) Battery 24 Volt DC system with 2 batteries Air inlet heater 24 volt preheat Compressor, air, CFM(l /min) 13.4 CFM (38) at 2,1rpm Air cleaner Dry type, replaceable element Horsepower, hp (kw) 385 (287) at 1,8rpm Oil filter Full flow and bypass with replaceable element Torque, Max. ft-lb (N-m) 1,31 (1,776) at 1,4rpm Fuel filter Spin-on type Capacity, gal.(liters) Fuel tank, gal.(liters) 15.6 (4), right side of carrier Cooling water 3.4 (13) Cooling Liquid pressurized, recirculating by-pass Lubrication 9.5 (36) Engine brake Jake brake TT-8XXL-4 14

15 STANDARD EQUPMENT FOR CRANE FOR CARRER - 5-section full power synchronized boom 37.7'~144.4' (11.5 m~44 m) - Cummins QSM11 turbo charged and inter cooled engine '~58.1' (9.9 m~17.7 m) two stage bi-fold lattice jib (tilt type) with Jake brake. with 3.5 o, 25 o or 45 o pinned offsets and self storing pins. - Ether injector - Auxiliary lifting sheave (single top) stowable - ZF AS-tronic automatic transmission, 12 forward and 2 reverse speeds. - Variable speed main hoist with grooved drum, cable follower - Front and spare tires : 445/65R22.5 Rear tires : 315/8R22.5 and 797' of 3/4" cable. - nter wheel differential lock - Variable speed auxiliary hoist with grooved drum, cable - Anti-lock Braking System (ABS) follower and 436' of 3/4" cable. - Towing hooks (Front and rear, eye type) - Drum rotation indicator (thumper type) main and auxiliary hoist - Carrier mounted storage box - Anti-Two block device (overwind cutout) - Trailer coupling device - Boom angle indicator - Air dryer and air cleaner dust indicator - Tadano electronic load moment indicator system (AML-L) - ZF - Servocom dual-circuit hydraulic steering system with emergency - Outrigger extension length detector steering pump - Electronic crane monitoring system - Front jack (Fifth jack) - 2 boom telescoping s - Aluminum fenders - Tadano twin swing system and 36 o positive swing lock - Windshield of laminated safety glass - Self centering finger control levers with pilot control - Side windows of hardened glass - Control pedals for boom hoist and boom telescoping - Windshield wiper and washer - 3 way adjustable cloth seat with armrests, high back and seat belt. - Roof hatch and Sun visor - Tinted safety glass and sun visor - Emergency hammer - Front windshield wiper and washer - Hot water cab heater with defroster - Roof window wiper and washer - Tilt telescoping steering wheel - Power window (cab door) - 3 way adjustable air suspension seat with 3 point type seat belt - Rear view mirrors (right and left side) - Speedometer, Odometer, Tachometer, Hourmeter and Tachograph - Mirror for main and auxiliary hoists - Air pressure gauge - Cigarette lighter - Engine temperature indicator - Electric fan in cab - Low coolant level warning lamp. - Cab floor mat - Fuel level indicator and lockable fuel tank cap - Hook block tie down front bumper - Gearbox display (ZF T/M indicator) with Gearbox malfunction buzzer - Non-slip paint - Engine over-run buzzer - Counterweight position indicator - Swing brake pressure drop buzzer for dolly - 3,7lbs, 4,lbs and 8,lbs three piece removable counterweight - Rotary beacon - Hydraulic circuit for dolly (Elevation, swing and swing brake) - Electric horn - Outrigger controls and sight bubble located in superstructure cab - High-beam light - Low noise - Front and rear fog lights - 3 working lights - Hazard warning system ton (5. metric ton) hook with swivel and safety latch - Back-up alarm and light - Hydraulic oil cooler - Electricarry adjustable and heated rear view mirror - FM/AM radio - Tire inflation kit - Cab floor mat - Ashtray and cigarette lighter - Extended exhaust pipe - Electical and pneumatic quick connections on rear bumper for boom - dolly lights and brakes. - Weighted hook storage compartment OPTONAL EQUPMENT - Hot water cab heater and air conditioner (Upper cab) - Main hook block HOSTNG SPECFCATONS LNE SPEEDS AND PULLS DRUM WRE ROPE CAPACTES Layer Speed Main or auxiliary hoist - 15'-3/4" (.4m) drum Main and auxiliary drum grooved lagging Wire Line speeds 2 Line pulls 3/4" (19mm) wire rope Available 1 Permissible 4 rope Rope per layer Total wire rope F.P.M m/min Lbs. kgf Lbs. kgf layer Feet Meters Feet Meters 1st High ,2 8,26 15,2 6, High ,7 7,57 13,9 6, High ,4 6,99 12,8 5, High ,3 6,49 11,9 5, th High ,4 6,6 11,1 5, th High ,5 5,68 1,4 4, th 3 High ,8 5,35 9,8 4, , Developed by machinery with each layer of wire rope, but not based DRUM DMENSONS on rope strength or other limitation in machinery or equipment. nch mm Line speeds based only on hook block, not loaded. Root diameter 15-3/4" 4 Seventh layer of wire rope is not recommended for hoisting operations. Length 22-3/4" 578 Permissible line pull may be affected by wire rope strength. Flange diameter 27-3/8" 695 TT-8XXL-4 15

16 13 o DMENSONS (R412) TAL SWNG 13'6-1/4" 8'6"(259) 1' 7-11/16" (5) 23' 7-1/2" 15' 9" 6' 9-7/8" (MAX.72) (MD.48) MN.37'8-11/16"~MAX.144'4-1/4"(115~44) 19'8-3/16"(6) 6'13/16"(185) 11'1-7/8"(363) 2 o 6'3-15/16"(193) 13'8-1/2"(418) 4'6-9/16"(1387) 1'3/16" (31) 2'4"(712) OFF SET 2'7-7/16"(8) 1'5-15/16"(32) 9'2-3/16"(28) 19'4-13/16"(5915) 14'9-1/2"(451) 4'8-3/4"(1443) 8'5-9/16"(258) 46'3-1/16"(141) GENERAL DMENSONS Tire : 445/65R22.5(Front) 315/8R22.5(Rear) Feet Meters Turning radius Front tire (curb to curb) 4' 8" 12.4 Over jib 48' 7" '11-7/8"(2132) 8' 6"(259) TT-8XXL-4 16