ROUGH TERRAIN CRANE DIMENSIONS

Transcription

1 GR-75XL-2 75 Ton Capacity (68. Metric Tons) HYDRAULC ROUGH TERRAN CRANE DMENSONS Note : Dimension is with boom angle at -1.6 degree. GENERAL DMENSONS (29.5 X 25 Tires) Feet Meters Turning radius 4 wheel steer 22'3-3/4" wheel steer 39' 1/2" 11.9 Tail swing of counterweight 13' 8-15/" 4.19 Specifications are subject to change without notice.

2 CRANE SPECFCATONS BOOM Five section full power synchronized telescoping boom, 36.1'~141.1' (11.m~43.m), of round box construction with six sheaves, 17-5/" (.44m) root diameter, at boom head. The synchronization system consists of two telescope cylinder an extension cable and retraction cable. Hydraulic cylinder fitted with holding valve. Two easily removable wire rope guards, rope dead end provided on both sides of boom head. Boom telescope sections are supported by wear pads both vertically and horizontally. Extension speed 15' in 128 seconds BOOM ELEVATON - By a double acting hydraulic cylinder wit holding valve. Elevation -1.6 o ~8.3 o, combination controls for hand or foot operation. Boom angle indicator. Automatic speed reduction and soft stop function. Boom raising speed 2 o to 6 o in 46 seconds. JB - two stage bi-fold lattice type, 3. o, 25 o or 45 o offset (tilt type) Single sheave, 15-5/8"(.396m) root diameter, at the head of both jib sections. Stored alongside base boom section. Jib length.2' (1.1m) or 58.1' (17.7m). Assistant cylinders for mounting and stowing, controlled at right side of superstructure. Self stowing jib mounting pins AUXLARY LFTNG SHEAVE (SNGLE TOP) Single sheave, 15-5/8"(.396m) root diameter. Mounted to main boom head for single line work (stowable ANT-TWO BLOCK - Pendant type over-winding cut ou device with audio-visual (FALURE lamp/buzzer) warning system SWNG Hydraulic axial piston motor through planetary swing speed reducer. Continuous 36 o full circle swing on ball bearing tur table at 2.4min -1 {rpm}. Equipped with manually locked/release swing brake. A 36 o positive swing lock for pick and carry and trave s, manually engaged in cab. Twin swing system: Free swing or lock swing controlled by selector switch on front console. HOST MAN HOST - Variable speed type with grooved drum driven b hydraulic axial piston motor through speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of auxiliary hoist. Equipped with cable follower and drum rotation indicator. DRUM - Grooved 15-3/4"(.4m) root diameter x 23-9/"(.599m wide. Wire rope: 771' of 3/4"diameter rope (235m of 19mm). Drum capacity: 1,74' (327.5m) 7 layers. Maximum single line pull: 1st layer,7 lbs (7,58kg). Maximum permissible line pull wire strength:15,6 lbs (7,85kg). AUXLARY HOST - Variable speed type with grooved drum drive by hydraulic axial piston motor through speed reducer. Power load lowering and raising. Equipped with automatic brake (neutral brake) and counterbalance valve. Controlled independently of main hoist. Equipped with cable follower and drum rotation indicator. WRE ROPE - Warrington seal wire, extra improved plow stee preformed, independent wire rope core, right regular lay. 3/4"(19 mm) 6X31 class HOOK BLOCKS 75 ton (68. metric ton) - 7 sheaves with swivel hook and safety latch. 6.2 ton (5.6 metric ton) - Weighted hook with swivel and safety latch. HYDRAULC SYSTEM PUMPS - Two variable piston pumps for crane functions Tandem gear pump for steering, swing and optional equipment. Powered by carrier engine. Pump disconnect for crane is engaged/ disengaged by rotary switch from operator's cab. CONTROL VALVES - Multiple valves actuated by pilot pressur with integral pressure relief valves RESERVOR gallon (84 lit.) capacity. External sight leve gauge. FLTRATON - BETA1=1 return filter, full flow with bypass protection, located inside of hydraulic reservoir. Accessible for easy replacement OL COOLER - Air cooled fan type CAB AND CONTROLS Both crane and drive operations can be performed from one cab mounted on rotating superstructure Left side, 1 man type, steel construction with sliding door access and safety glass windows opening at side. Door window is powered control. Windshield glass window and roof glass window are shatter-resistant. Tilt-telescoping steering wheel. Adjustable control lever stands for swing, boom hoist, boom telescoping, auxiliary hoist and main hoist. Control lever stands can change neutral positions and tilt for easy access to cab. 3 way adjustab operator's seat with high back, headrest and armrest. Engine throttle knob. Foot operated controls: boom elevatin boom telescoping, service brake and engine throttle. Hot water cab heater and air conditioning. Dash-mounted engine start/stop, monitor lamps, cigarette lighter, drive selector switch, parking brake switch, steering select switch, power window switch, pump engaged/disengag switch, swing brake switch, telescoping / auxiliary hoist select switch, outrigger controls, free swing / lock swing selector switch, eco switch and ashtray. nstruments - Torque converter oil temperature, engine water temperature, air pressure, fuel, speedometer, tachomete hour meter and odometer / tripmeter. Hydraulic oil pressure is monitored and displayed on the AML-C display panel. DRUM - Grooved 15-3/4"(.4m) root diameter x 23-9/"(.599m wide. Wire rope: 436' of 3/4"diameter rope (1m of 19mm). Drum capacity: 1,74' (327.5m) 7 layers. Maximum single line pull: 1st layer,7 lbs (7,58kg). Maximum permissible line pull wire strength:15,6 lbs (7,85kg). 2

3 Tadano electronic LOAD MOMENT NDCATOR system (AML-C) including: h Control lever lockout function h Boom position indicator h Outrigger state indicator h Boom angle / boom length / jib offset angle / jib length / load radius / rated lifting capacities / actual loads read out h Ratio of actual load moment to rated load moment indication h Automatic Speed Reduction and Soft Stop function on boom elevation and swing h Working condition register switch h Load radius / boom angle / tip height / swing range preset function h External warning lamp h Tare function h Fuel consumption monitor h Main hoist / auxiliarly hoist select h Drum rotation indicator (audible and visible type) main and auxiliary hoist TADANO AML-C monitors outrigger extended length and automatically programs the corresponding "RATED LFTNG CAPACTES" table Operator's right hand console includes transmission gear selector and sight level bubble. Upper console includes working light switch, roof washer and wiper switch emergency outrigger set up key switch, jib equipped/removed select switch, eco switch, boom emergency telescoping switch (2nd and 3rd/4th/top) and air conditioning control switch. Swing lock lever. NOTE: Each crane motion speed is based on unladen conditions. CARRER SPECFCATONS TYPE - Rear engine, left hand steering, driving axle 2-wa selected type by manual switch, 4x2 front drive, 4x4 front and rear drive. FRAME - High tensile steel, all welded mono-box constructio SUSPENSON - Front: Rigid mounted to frame. Rear: Pivo mounted with hydraulic lockout device. BRAKE SYSTEMS - Service: Air over hydraulic disc brakes o all 4 wheels. Parking/Emergency: Spring applied-air release brake acting on input shaft of front axle. Auxiliary: Electropneumatic operated exhaust brake TRANSMSSON - Electronically controlled full automati transmission. Torque converter driving full powershift with driving axle selector. 6 forward and 2 reverse speeds, consta TRES PR(OR) or PR(OR) mesh. 3 speeds - high range - 2 wheel drive; 4 wheel driv OUTRGGERS - Four hydraulic, beam and jack outriggers 3 speeds - low range - 4 wheel drive Vertical jack cylinders equipped with integral holding valve. Each outrigger beam and jack is controlled independently from cab. TRAVEL SPEED - 22 mph (36 km/h) Beams extend to 23' 11-3/8" (7.3 m) center-line and retract t within 1' 1-1/2" (3.315 m) overall width with floats. Outrigger AXLE - Front: Full floating type, steering and driving axle wi jack floats are attached thus eliminating the need of manuall planetary reduction. Rear: Full floating type, steering and driving attaching and detaching them. Controls and sight bubble located axle with planetary reduction and non-spin rear differential. in superstructure cab. Four outrigger extension lengths are provided with corresponding "RATED LFTNG CAPACTES" for STEERNG- Hydraulic power steering controlled by steerin crane duty in confined areas wheel. Four steering s available: 2 wheel front, 2 wheel Min. Extension 8' 1-5/"(2.7m) center to center rear, 4 wheel coordinated and 4 wheel crab. Mid. Extension 18' 1/2"(5.5m) center to center Mid. Extension 21' 11-3/4"(6.7m) center to center Max. Extension 23' 11-3/8"(7.3m) center to center Float size(diameter) 1' 11-5/8" (.6m) ENGNE Model Mitsubishi 6M6-TLA3B Radiator Fin and tube core, thermostat controlled Type Direct injection diese Fan, in.(mm) Suction type, 6-blade, 23.6 (6) dia. No. of cylinders 6 Starting 24 volt Combustion 4 cycle, turbo charged and after cooled Charging 24 volt system, negative ground BoreXStroke, in.(mm) X (118X115) Battery 2-12 amp. Hour Displacement, cu. in (liters) 46 (7.54) Compressor, air, CFM(l /min) 29 CFM () at 2,6rpm Air inlet heater 24 volt preheat Horsepower (kw) Gross 267 (2) at 2,6rpm Air cleaner Dry type, replaceable elemen Torque, Max. ft-lb (kgm) 579 (8) at 1,4rpm Oil filter Full flow with replaceable element Capacity, gal.(liters) Fuel filter Full flow with replaceable element Cooling water 3.4 (13) Fuel tank, gal.(liters) 79.2 (3), right side of carrier Lubrication (13-15) Cooling Liquid pressurized, recirculating by-pass Fuel 79.2 (3) 3

4 STANDARD EQUPMENT - Five section full power partially synchronized boom - ndependently controlled outriggers 36.1'~141.1' (11. m~43. m) - Four outrigger extension positions -.2' or 58.1' (1.1 m or 17.7 m) bi-fold lattice jib (tilt type) - Self-storing outrigger pads with 3.5 o, 25 o or 45 o pinned offsets and self storing pins - Mitsubishi 6M6-TLA3B turbo charged after cooled engine - Auxiliary lifting sheave (single top) stowable (267HP) with exhaust brake - Variable speed main hoist with grooved drum, cable follower - Electronic controlled automatic transmission driven and 771' of 3/4" cable. by torque converter - Variable speed auxiliary hoist with grooved drum, cable - 4 X 4 X 4 drive/steer follower and 436' of 3/4" cable. - Non-spin rear differential - Drum rotation indicator (audible,visible and thumper type) main - Automatic rear axle oscillation lockout system and auxiliary hoist PR (OR) tires or PR (OR) tires - Anti-Two block device (overwind cutout) - Disc brakes - Boom angle indicator - Fenders - Tadano electronic load moment indicator system (AML-C) - Air dryer - Outrigger extension length detector - Water separator with filter(high filtration) - Electronic crane monitoring system - Engine over-run alarm - Tadano twin swing system and 36 o positive swing lock - Back-up alarm - Self centering finger control levers with pilot control - Low oil pressure/high water temp. warning device (visual) - Control pedals for boom elevating and boom telescoping - Rear steer centering light - 3 way adjustable cloth seat with armrests, high back - Air cleaner dust indicator and seat belt - Full instrumentation package - Tilt-telescoping steering wheel - Complete highway light package - Tinted safety glass and sun visor - Tool storage compartment - Front windshield wiper and washer - Tire inflation kit - Roof window wiper and washer - 24 volt electric system - Power window (cab door) ton (5.6 metric ton) hook with swivel - Rear view mirrors (right and left side) - 75 ton (68. metric ton) - 7 sheave with swivel hook and - Mirror for main and auxiliary hoists safety latch for 3/4"(19mm) wire rope - Cigarette lighter and ashtray - Towing hooks-front and rear - Cab floor mat - Lifting eyes - Pump disconnect in operator's cab - Hook block tie down (front bumper) - Hydraulic oil cooler - Weighted hook storage compartment - Hot water cab heater and air conditioner - Halogen head lamp - Positive control - Telecommunications terminal (HELLO-NET Owner s Site) - Quick reeving type bi-fold jib - Fuel consumption monitor - Work lights OPTONAL EQUPMENT HOSTNG PERFORMANCE LNE SPEEDS AND PULLS DRUM WRE ROPE CAPACTES Layer Main or auxiliary hoist /4" (.4m) drum Main and auxiliary drum grooved lagging Wire Line speeds 1 Line pulls 3/4" (19mm) wire rope rope Available 2 Rope per layer Total wire rope layer F.P.M m/min Lbs. kgf Feet Meters Feet Meters 1st ,7 7, nd ,3 6, rd , 6, th , 5, th ,1 5, th ,3 5, th ,6 4, * Maximum permissible line pull may be affected by wire rope strength. Wire rope strength (6x31 class) = 15,6lbs(7,85kg) DRUM DMENSONS nch mm Root diameter 15-3/4" 4 1 Line speeds based only on hook block, not loaded. Length 23-9/" Developed by machinery with each layer of wire rope, but not based Flange diamete 27-3/8" 695 on rope strength or other limitation in machinery or equipment. 3 Seventh layer of wire rope are not recommended for hoisting operations. 4

5 GR-75XL WORKNG RANGE CHART 5

6 GR-75XL WORKNG RANGE CHART 6

7 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' 141.1' B C (11m) C (15m) C C C C C C C C C C C (39m) C (43m) 8' 72 ###### 77 9, 1' 68 ###### 75 9, 79 7, ,1 12' 64 ###### 72 9, 77 7, , , ,1 15' 59 98, 68 9, 73 7, , , , , ,5 2' 48 75, , , , , , , , , ,7 25' 6, 54 59, , , , , , , , , , , , 3' 46 45, , 58 44, , ,2 7 38, , , , , , , 79 19,8 35' 36, , ,3 6 34,6 6 32,4 34,7 25,9 7 3,6 7 23, ,6 73 2,1 75 2, ,5 4' 21 26, ,3 45 3, , , , , ,7 67 2,9 7 24,9 7 18, , ,2 45' 38 19, ,6 5 21,3 5 24, ,2 58 2, , , , ,4 7 17,7 74,9 5' 29 15,9 28 2, ,3 45 2, , , 6 18,7 6 17, , , ,1 71,5 55' 13 11, , 38 14, , , 49 17, , ,5 62, 62 14, 15,6 69,1 6' 31 11, , 45 12, , , , 58 13, , , ,9 65' 22 9, , 4 1,5 4 13, , 49 12, , ,6 6 12, ,9 7' 34 8, ,5 45 9, ,6 52 9,8 52 1,6 57 1,9 62 1,3 75' 26 7,5 26 1,1 4 8, 4 1,3 48 8,4 48 9,7 54 9,5 59 8,8 8' 15 6,3 18 9, 35 6,8 35 9,1 44 7,2 45 9, 51 8,3 57 7,7 85' 29 5,8 29 8, 4 6,2 41 8,1 48 7,2 54 6,6 9' 21 5, 21 7,2 36 5,3 36 7,2 45 6,3 51 5,7 95' 31 4,5 31 6,4 41 5,6 48 4,9 1' 25 3,9 25 5,8 37 4,9 45 4,3 15' 3,3 5,2 4,3 42 3,7 11' 27 3,8 38 3,1 115' 21 3,3 34 2,6 12' 8 2,9 3 2,2 125' 24 1,8 13' 17 1,5 135' 14' D Telescoping conditions (%) 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' 141.1' C B (11m) B (15m) B B B B B B B B B B B (39m) B (43m) 28.9' 26, 42.',8 55.4' 1,8 55.4' 13,7 68.6' 7,9 68.6' 1,1 81.7' 6, 81.7' 8,4 94.2' 4,4 94.5' 6,6 17.' 3,1 17.' 4, ' 2, ' 1,1,, A :Boom length in feet B :Load radius in feet C :Loaded boom angle ( o ) D :Minimum boom angle ( o ) for indicated length (no load) NOTE The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-C) is based on the standard number of parts of line listed in the chart. Standard number of parts of line for each boom length should be according to the following table. Boom length in feet 36.1' 36.1' to 49.2' 49.2' to 62.3' (meters) (11m) (11m to 15m) (15m to 19m) Telescoping, 62.3' to 141.1' (19m to 43m), Single top Jib, Number of parts of line

8 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 36 o ROTATON 141.1' (43.m) Boom +.2' (1.1m) Jib 141.1' (43.m) Boom ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 9,3 48.6' 8,8 55.4' 7, ' 5,7 65.6' 5,2 76.8' 3, ' 9,3 51.8' 8,5 58.4' 7, ' 5,7 69.2' 5, 8.1' 3, ' 9,3 54.8' 8,2 61.' 7, ' 5,7 72.5' 4,9.3' 3, ' 9,3 58.1' 8, 64.3' 6, ' 5,7 75.8' 4,7 86.' 3, ' 9,3 61.' 7,8.9' 6, ' 5,7 79.1' 4,6 89.2' 3, ' 9,3 64.' 7,5 69.9' 6, ' 5,7 82.3' 4,4 92.2' 3, ' 9,1 69.9' 7,2 75.1' 6, ' 5,7 88.9' 4,1 97.8' 3, ' 8,2 78.4' 6,7.3' 5, ' 5,6 98.8' 3,8.' 3, ' 7,8 84.' 6,4 87.6' 5, ' 5,3 15.' 3, ' 3, 65.7' 7,2 91.9' 6, 95.1' 5, ' 4, ' 3, ' 2, ' 6,7 96.8' 5,8 99.7' 5, ' 4, ' 3, ' 2, ' 5,8 13.7' 5,2.3' 4, ' 3,9 127.' 3, 13.9' 2, ' 5,1 17.9' 4,6 11.6' 4, ' 3, ' 2, ' 2,6 55.3' 4, ' 3,8 1.1' 3, ' 2, ' 2, ' 2, ' 3, ' 3, ' 3, ' 2, ' 1, ' 1, ' 2,9 124.' 2,7 125.' 2, ' 1, ' 1, ' 1, ' 2, ' 2, ' 2, ' 1, ' 1, ' 1, ' 2, 132.5' 1,9 1.2' 1, ' 1, ' 1, ' 1, ' 1,3 14.7' 1, ' 1, ' 1, ON OUTRGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 36 o ROTATON 128.'(39.m) Boom(telescoping ) +.2' (1.1m) Jib 128.'(39.m) Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset 8 3.8' 1,1 44.' 9,5 51.5' 7, ' 6,2 6.7' 5,5 72.5' 4, ' 1,1 46.9' 9,2 54.1' 7, ' 6,2 64.' 5,3 75.1' 3, ' 1,1 49.5' 8,9 56.8' 7, ' 6,2 67.3' 5,1 78.1' 3, ' 1,1 52.5' 8,6 59.4' 7, ' 6,2 7.2' 4,9 8.7' 3, ' 1,1 55.1' 8,4 61.7' 7, ' 6,2 73.5' 4,8.3' 3, ' 1,1 58.1' 8,2 64.' 6, ' 6,2 76.1' 4,6 86.' 3, ' 1, 63.3' 7,7 68.9' 6, ' 6,2 82.3' 4,3 91.2' 3, ' 9,1 7.9' 7,1 76.4' 6, ' 6, 91.2' 3,9 98.8' 3, ' 8,6 76.1' 6,8 8.7' 5, ' 5,5 96.5' 3,7 13.7' 3, ' 7,9.3' 6,3 87.3' 5, ' 4,9 14.7' 3,4 11.6' 2, ' 7,6 87.9' 6, 91.5' 5, ' 4,6 19.6' 3, ' 2, ' 6,7 94.5' 5,6 97.8' 5, ' 4, ' 3, 122.7' 2, ' 6,2 99.1' 5,4 11.7' 4, ' 3, ' 2, ' 2, ' 5,5 15.3' 4,9 17.6' 4, ' 3, ' 2,8 1.5' 2, ' 5,1 18.9' 4,7 11.9' 4, ' 3,4 1.9' 2, ' 2, ' 4, ' 4,3 1.1' 4, ' 3,1 14.4' 2,5 143.' 2, ' 4, ' 3, ' 3, ' 2, ' 2, ' 2, ' 3,7 123.' 3, ' 3, ' 2, ' 2, 149.9' 1, ' 3,3 126.' 3, ' 2, ' 1, ' 2,9 13.2' 2, ' 1, ' 1, ' 2, ' 2, ' 1, ' 1, ' 2, ' 2, ' 1,2 2.7' 1, ' 2, ' 1, ' 1,1 5.' ' 1, ' 1, ' 1, ' 1, ' 1, ' 1, ON OUTRGGERS FULLY EXTENDED 23' 11-3/8"(7.3m) SPREAD 36 o ROTATON 114.8'(35m) Boom(telescoping ) +.2' (1.1m) Jib 114.8'(35m)Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 12,3 4.4' 11,3 47.6' 8, ' 7,1 56.8' 6,2 68.9' 4, ' 12,3 42.7' 1,4 49.5' 8, ' 7,1 59.4' 5,6 71.2' 4,2 78.8' 12,3 45.6' 1,4 52.2' 8, ' 7,1 62.7' 5,6 73.8' 4, ' 12,3 48.2' 1,4 54.8' 8, ' 7,1 65.6' 5,6 76.8' 4, ' 12,3 5.5' 1,1 56.8' 8, ' 7,1 68.6' 5,5 79.1' 4, ' 12,3 53.1' 9,9 59.1' 7, ' 7,1 71.2' 5,4 81.7' 4, ' 12,3 58.1' 9,3 63.6' 7, ' 7,1 76.8' 5, 86.3' 4, ' 11,4 65.' 8,6 7.2' 7, ' 7,1 84.6' 4,7 93.2' 3, ' 1,8 69.6' 8,2 74.1' 6, ' 6,8 89.9' 4,5 97.8' 3, ' 1,1 76.1' 7,7 8.4' 6, ' 6,1 97.8' 4,2 14.' 3, ' 9,6 8.4' 7,3 84.3' 6, ' 5,7 12.' 4, 18.3' 3, ' 9, 86.6' 6,9 89.9' 6, ' 5,2 18.9' 3, ' 3, ' 8,3 9.6' 6,7 93.5' 6, ' 4, ' 3, ' 3, ' 7, 95.8' 6,2 98.8' 5,8 55.' 4, ' 3,4 123.' 3, ' 6,3 99.4' 5,6 11.7' 5, ' 4, ' 3, ' 3, ' 5,3 14.7' 4,8.3' 4, ' 3, ' 3,1 13.9' 2, ' 4,8 17.6' 4,3 18.9' 4, ' 3, ' 2,7 1.5' 2,5 45.' 4, ' 3, ' 3, ' 2, ' 2, ' 2, ' 3, ' 3, ' 2,3 14.4' 2, ' 3, ' 3, ' 1, ' 1, ' 2, ' 2, ' 1,7 147.' 1, ' 2,5 125.' 2, ' 1,4 15.6' 1, ' 2,3 127.' 2, ' 1, ' 1, ' 2, 129.9' 1, ' 1, ' 1,6 1.9' 1,5 C :Loaded boom angle ( o ) ' 1,3 R :Load radius in feet ' 1,1 W :Rated lifting capacity in pounds 8

9 GR-75XL RATED LFTNG CAPACTES (N POUNDS) A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' 141.1' B C (11m) C (15m) C C C C C C C C C C C (39m) C (43m) 8' 72 ###### 77 9, 1' 68 ###### 75 9, 79 7, ,1 12' 64 ###### 72 9, 77 7, , , ,1 15' 58 94,8 68 9, 73 7, , , , , ,5 2' 48 72, , , , , , , , , ,7 25' 54, , , , , , , , , , , , , 3' 47 36, ,3 58 4, , ,2 7 38, ,5 73 3, , , , , 79 19,8 35' 36 26, ,7 52 3,8 6 27,3 6 31,3 28,2 25,9 7 28,9 7 23, ,6 73 2,1 75 2, ,5 4' 22 2, , ,3 55 2, , , , ,5 2, , 7 18, , ,2 45' 38 15, 37 19,6 5,4 5 2, ,3 58 2, , , , , ,5 73,4 5' 28 11,7 27, ,1 45, ,9 54,9 6 14,5 6 17, , ,6 68, ,5 55' 11 9,1 1 13,4 38 1, , 49 11, , , , , , 65 13, ,9 6' 31 8, ,8 45 9, ,1 52 9, ,3 58 1, , ,5 1,8 65' 21 6,7 21 1,1 39 7,6 39 1,4 49 8,1 49 1,6 55 8,5 55 1,7 6 9,8 64 9, 7' 34 6,2 34 8,9 45 6,7 45 9,1 52 7,1 52 9,2 57 8,4 62 7,6 75' 26 5, 26 7,7 4 5,6 4 7,9 48 5,9 48 8, 54 7,2 59 6,4 8' 15 4, 15 6,7 35 4,5 35 6,9 44 4,9 44 7, 51 6,2 56 5,4 85' 29 3,7 29 6, 4 4,1 4 6,1 48 5,3 53 4,5 9' 21 2,9 21 5,2 36 3,3 36 5,3 44 4,5 5 3,8 95' 31 2,6 3 4,6 4 3,8 47 3,1 1' 24 2, 24 4, 36 3,2 44 2,5 15' 15 1,5 15 3,5 32 2,7 41 2, 11' 27 2,2 38 1,5 115' 2 1,8 12' 8 1,5 125' 13' 135' 14' D Telescoping conditions (%) 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 21' 11-3/4"(6.7m) SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' C B (11m) B (15m) B B B B B B B B B B B (39m) 28.9' 26, 42.3',1 55.4' 9, 55.1' 13,2 68.6' 5,7 68.6' 9, 81.7' 3,7 81.7' 6,4 94.5' 2,4 94.2' 4,6 17.' 1,3 17.' 3, ' 1,5, A :Boom length in feet B :Load radius in feet C :Loaded boom angle ( o ) D :Minimum boom angle ( o ) for indicated length (no load) ON OUTRGGERS MD EXTENDED 21' 11-3/4"(6.7m) SPREAD 36 o ROTATON NOTE The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-C) is based on the standard number of parts of line listed in the chart. Standard number of parts of line for each boom length should be according to the following table. Boom length in feet 36.1' 36.1' to 49.2' 49.2' to 62.3' (meters) (11m) (11m to 15m) (15m to 19m) Telescoping, 62.3' to 141.1' (19m to 43m), Single top Jib, Number of parts of line

10 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 21' 11-3/4"(6.7m) SPREAD 36 o ROTATON 141.1' (43.m) Boom +.2' (1.1m) Jib 141.1' (43.m) Boom ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 9,3 48.6' 8,8 55.4' 7, ' 5,7 65.6' 5,2 76.8' 3, ' 9,3 51.8' 8,5 58.4' 7, ' 5,7 69.2' 5, 8.1' 3, ' 9,3 54.8' 8,2 61.' 7, ' 5,7 72.5' 4,9.3' 3, ' 9,3 58.1' 8, 64.3' 6, ' 5,7 75.8' 4,7 86.' 3, ' 9,3 61.' 7,8.9' 6, ' 5,7 79.1' 4,6 89.2' 3, ' 9,3 64.' 7,5 69.9' 6, ' 5,7 82.3' 4,4 92.2' 3, ' 9,1 69.9' 7,2 75.1' 6, ' 5,7 88.9' 4,1 97.8' 3, ' 8,2 78.4' 6,7.3' 5, ' 5,6 98.8' 3,8.' 3, ' 7,8 84.' 6,4 87.6' 5, ' 5,3 15.' 3, ' 3, ' 6,1 9.9' 5,2 94.5' 4, ' 4, ' 3, ' 2, ' 5,2 95.5' 4,5 98.8' 4, ' 3, ' 2,6 123.' 2, ' 4, 12.' 3,5 15.' 3, ' 2,5 125.' 1, ' 1, ' 3,3.3' 2,9 18.9' 2, ' 2, 129.3' 1,5 1.5' 1, ' 2, ' 2, ' 2, ' 1, ' 1, 139.4' ' 2, 1.8' 1, ' 1, ' ' 1, ' 1, ' 1, ' 1, ' ' 9 ON OUTRGGERS MD EXTENDED 21' 11-3/4"(6.7m) SPREAD 36 o ROTATON 128.'(39.m) Boom(telescoping ) +.2' (1.1m) Jib 128.'(39.m) Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset 8 3.8' 1,1 44.' 9,5 51.5' 7, ' 6,2 6.7' 5,5 72.5' 4, ' 1,1 46.9' 9,2 54.1' 7, ' 6,2 64.' 5,3 75.1' 3, ' 1,1 49.5' 8,9 56.8' 7, ' 6,2 67.3' 5,1 78.1' 3, ' 1,1 52.5' 8,6 59.4' 7, ' 6,2 7.2' 4,9 8.7' 3, ' 1,1 55.1' 8,4 61.7' 7, ' 6,2 73.5' 4,8.3' 3, ' 1,1 58.1' 8,2 64.' 6, ' 6,2 76.1' 4,6 86.' 3, ' 1, 63.3' 7,7 68.9' 6, ' 6,2 82.3' 4,3 91.2' 3, ' 9,1 7.9' 7,1 76.4' 6, ' 6, 91.2' 3,9 98.8' 3, ' 8,6 76.1' 6,8 8.7' 5, ' 5,5 96.5' 3,7 13.7' 3, ' 7,9.3' 6,3 87.3' 5, ' 4,9 14.7' 3,4 11.6' 2, ' 7,4 87.9' 6, 91.5' 5, ' 4,6 19.6' 3, ' 2, ' 6, 94.5' 5,2 97.8' 4, ' 4, ' 3, 122.7' 2, ' 5,2 98.4' 4,6 11.4' 4, ' 3, ' 2, ' 2, ' 4,3 14.3' 3,8 17.' 3, ' 2, ' 2, ' 2, ' 3,7 17.9' 3,3 11.6' 3, ' 2, ' 1, ' 1,7 5.3' 3, 113.5' 2, ' 2, ' 1, ' 1, ' 1, ' 2,6 1.8' 2, ' 2, ' 1, ' 1, ' 1, ' 2, ' 1,9 123.' 1, ' 1, 147.3' ' 1,8 125.' 1, ' ' 1, ' 1, ' 1, ' 1, ' ' 9 ON OUTRGGERS MD EXTENDED 21' 11-3/4"(6.7m) SPREAD 36 o ROTATON 114.8'(35m) Boom(telescoping ) +.2' (1.1m) Jib 114.8'(35m)Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 12,3 4.4' 11,3 47.6' 8, ' 7,1 56.8' 6,2 68.9' 4, ' 12,3 42.7' 1,4 49.5' 8, ' 7,1 59.4' 5,6 71.2' 4,2 78.8' 12,3 45.6' 1,4 52.2' 8, ' 7,1 62.7' 5,6 73.8' 4, ' 12,3 48.2' 1,4 54.8' 8, ' 7,1 65.6' 5,6 76.8' 4, ' 12,3 5.5' 1,1 56.8' 8, ' 7,1 68.6' 5,5 79.1' 4, ' 12,3 53.1' 9,9 59.1' 7, ' 7,1 71.2' 5,4 81.7' 4, ' 12,3 58.1' 9,3 63.6' 7, ' 7,1 76.8' 5, 86.3' 4, ' 11,4 65.' 8,6 7.2' 7, ' 7,1 84.6' 4,7 93.2' 3, ' 1,8 69.6' 8,2 74.1' 6, ' 6,8 89.9' 4,5 97.8' 3,6 65.9' 9,8 76.1' 7,7 8.4' 6, ' 6,1 97.8' 4,2 14.' 3, ' 8,5 8.4' 7,1 84.3' 6, ' 5,7 12.' 4, 18.3' 3, ' 6,8 86.' 5,9 89.6' 5, ' 4,7 18.9' 3, ' 3, ' 6, 89.6' 5,2 92.8' 4, ' 4, 112.9' 3, ' 2, ' 4,9 95.1' 4,2 98.1' 4, ' 3, ' 2, ' 2, ' 4,2 98.8' 3,7 11.' 3, ' 2, ' 2,2 126.' 1, ' 3,4 13.7' 3, 15.6' 2, ' 2, ' 1,7 13.2' 1, ' 3, 17.' 2,6 18.3' 2, ' 1, ' 1,4 1.5' 1, ' 2, ' 2, ' 2, ' 1, ' 1, 137.5' ' 2, 114.2' 1, ' ' 1, ' 1, ' 1, ' 1, ' 1, 124.3' 1, C :Loaded boom angle ( o ) R :Load radius in feet W :Rated lifting capacity in pounds 1

11 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 18' 1/2"(5.5m) SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' 141.1' B C (11m) C (15m) C C C C C C C C C C C (39m) C (43m) 8' 72 ###### 77 9, 1' 68 ###### 75 9, 79 7, ,1 12' 64 ###### 72 9, 77 7, , , ,1 15' 58 87, 68 86,5 73 7, , , , , ,5 2' 48 61, 62 6, 69 59, , , , , , , ,7 25' 38, , , , , , , , , , , , , 3' 46 26, ,7 58 3, , , , , , , , , , 79 19,8 35' 35 19, 52 18, ,3 6 2,2 6 24, 21,2 24,4 7 21,9 7 23, ,3 73 2,1 75 2, ,5 4' 21 14, , , , ,9 62, ,3 17, 19,6 7 17,4 7 18, , ,2 45' 38 1, ,6 5 11,7 5 15, , , , , ,8 67,1 7 15, ,2 5' 29 7, ,8 45 9, ,4 54 1, 54 12,8 6 1,6 6 13, , , , ,7 55' 12 5,6 11 9,7 38 7, 38 1,3 49 7,8 49 1,6 56 8,5 56 1,9 61 9, 61 11,1 65 1,3 68 9,6 6' 31 5,3 31 8,6 45 6,2 44 8,9 52 6,8 52 9,2 58 7,2 58 9,3 62 8,5 7,8 65' 22 3,9 21 7,2 39 4,8 39 7,5 48 5,4 48 7,7 55 5,8 55 7,9 6 7,1 63 6,4 7' 34 3,6 34 6,3 45 4,2 45 6,5 52 4,7 52 6,7 57 5,9 61 5,2 75' 26 2,7 25 5,3 39 3,2 39 5,5 48 3,7 48 5,7 54 4,9 58 4,2 8' 15 1,9 15 4,5 34 2,4 34 4,7 44 2,8 44 4,8 5 4, 56 3,4 85' 28 1,7 29 3,9 4 2,1 4 4,1 47 3,3 53 2,6 9' 21 3,3 36 1,5 36 3,4 44 2,6 5 2, 95' 3 2,9 4 2,1 47 1,4 1' 24 2,4 36 1,6 15' 15 2, 11' 115' 12' 125' 13' 135' 14' D Telescoping conditions (%) 2nd boom 3rd boom 4th boom Top boom, , LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MD EXTENDED 18' 1/2"(5.5m) SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) C B (11m) B (15m) B B B B B B B B 28.9' 25,8 42.3' 12,6 55.4' 5,5 55.4' 9,7 71.9' 3,1 68.6' 6,4 81.7' 1,8 81.7' 4,2 94.5' 17.' 2,9 1,3, A :Boom length in feet B :Load radius in feet C :Loaded boom angle ( o ) D :Minimum boom angle ( o ) for indicated length (no load) NOTE The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-C) is based on the standard number of parts of line listed in the chart. Standard number of parts of line for each boom length should be according to the following table. Boom length in feet 36.1' 36.1' to 49.2' 49.2' to 62.3' (meters) (11m) (11m to 15m) (15m to 19m) Telescoping, 62.3' to 141.1' (19m to 43m), Single top Jib, Number of parts of line

12 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON OUTRGGERS MD EXTENDED 18' 1/2"(5.5m) SPREAD 36 o ROTATON 141.1' (43.m) Boom +.2' (1.1m) Jib 141.1' (43.m) Boom ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 9,3 48.6' 8,8 55.4' 7, ' 5,7 65.6' 5,2 76.8' 3, ' 9,3 51.8' 8,5 58.4' 7, ' 5,7 69.2' 5, 8.1' 3, ' 9,3 54.8' 8,2 61.' 7, ' 5,7 72.5' 4,9.3' 3, ' 9,3 58.1' 8, 64.3' 6, ' 5,7 75.8' 4,7 86.' 3, ' 9,3 61.' 7,8.9' 6, ' 5,7 79.1' 4,6 89.2' 3, ' 9,3 64.' 7,5 69.9' 6, ' 5,7 82.3' 4,4 92.2' 3, ' 8,3 69.6' 6,9 74.8' 6, ' 5,4 88.9' 4,1 97.8' 3,4 7.3' 6,2 76.8' 5,3 81.7' 4, ' 3,9 96.8' 3, 15.3' 2, ' 5,1 81.7' 4,4 86.3' 4, ' 3,1 12.' 2,4 19.6' 2, ' 3,8 9.9' 3,3 92.8' 3, ' 2,1 19.6' 1,6 1.5' 1, ' 3, 93.5' 2,7 97.1' 2, ' 1, ' 1, ' 1, ' 2,1 1.4' 1,9 13.7' 1, ' 1, ' 1,6 15.' 1,4 17.6' 1, ' 9 ON OUTRGGERS MD EXTENDED 18' 1/2"(5.5m) SPREAD 36 o ROTATON 128.'(39.m) Boom(telescoping ) +.2' (1.1m) Jib 128.'(39.m) Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset 8 3.8' 1,1 44.' 9,5 51.5' 7, ' 6,2 6.7' 5,5 72.5' 4, ' 1,1 46.9' 9,2 54.1' 7, ' 6,2 64.' 5,3 75.1' 3, ' 1,1 49.5' 8,9 56.8' 7, ' 6,2 67.3' 5,1 78.1' 3, ' 1,1 52.5' 8,6 59.4' 7, ' 6,2 7.2' 4,9 8.7' 3, ' 1,1 55.1' 8,4 61.7' 7, ' 6,2 73.5' 4,8.3' 3, ' 1,1 58.1' 8,2 64.' 6, ' 6,2 76.1' 4,6 86.' 3, ' 1, 63.3' 7,7 68.9' 6, ' 6,2 82.3' 4,3 91.2' 3, ' 9,1 7.9' 7,1 76.4' 6, ' 6, 91.2' 3,9 98.8' 3, ' 7,7 75.8' 6,4 8.7' 5, ' 5,1 96.5' 3,7 13.7' 3, ' 6, 82.3' 5,1 86.6' 4, ' 3,9 14.' 3,1 11.2' 2, ' 5,1 86.6' 4,4 9.6' 4, ' 3,3 18.6' 2, ' 2, ' 4, 92.8' 3,4 96.5' 3, ' 2, ' 1, ' 1, ' 3,3 96.8' 2,9 1.4' 2, ' 2, 119.8' 1,5 125.' 1, ' 2,5 12.7' 2,2.' 2, ' 1, ' 1, ' 2,1.6' 1,8 19.3' 1, ' 1, 5 15.' 1, ' 1, ' 1, ' 1, ' 1, 117.5' 9 ON OUTRGGERS MD EXTENDED 18' 1/2"(5.5m) SPREAD 36 o ROTATON 114.8'(35m) Boom(telescoping ) +.2' (1.1m) Jib 114.8'(35m)Boom(telescoping ) ' (17.7m) Jib C 3.5 o offset 25 o offset 45 o offset C 3.5 o offset 25 o offset 45 o offset ' 12,3 4.4' 11,3 47.6' 8, ' 7,1 56.8' 6,2 68.9' 4, ' 12,3 42.7' 1,4 49.5' 8, ' 7,1 59.4' 5,6 71.2' 4,2 78.8' 12,3 45.6' 1,4 52.2' 8, ' 7,1 62.7' 5,6 73.8' 4, ' 12,3 48.2' 1,4 54.8' 8, ' 7,1 65.6' 5,6 76.8' 4, ' 12,3 5.5' 1,1 56.8' 8, ' 7,1 68.6' 5,5 79.1' 4, ' 12,3 53.1' 9,9 59.1' 7, ' 7,1 71.2' 5,4 81.7' 4, ' 12,3 58.1' 9,3 63.6' 7, ' 7,1 76.8' 5, 86.3' 4, ' 1,7 65.' 8,5 7.2' 7, ' 7,1 84.6' 4,7 93.2' 3, ' 9, 69.2' 7,3 74.1' 6, ' 6, 89.9' 4,5 97.8' 3, ' 6,9 75.1' 5,8 79.4' 5, ' 4,7 96.5' 3,5 13.3' 3, ' 5,9 79.1' 4,9.3' 4, ' 3,9 1.7' 2,9 17.3' 2, ' 4,5 85.' 3,9 88.6' 3, ' 2,9 17.3' 2, ' 1, ' 3,8 88.6' 3,3 92.2' 3, ' 2, ' 1,8 1.8' 1, ' 2,9 94.2' 2,5 97.1' 2, ' 1, ' 1,2 122.' 1, ' 2,4 97.8' 2,1 1.4' 1, ' 1, ' 1,7 12.7' 1,5 15.' 1, ' 1,3.' 1,1 17.9' 1,1 C :Loaded boom angle ( o ) R :Load radius in feet W :Rated lifting capacity in pounds 12

13 GR-75XL RATED LFTNG CAPACTES (N POUNDS) A 36.1' 49.2' 62.3' (19m) 75.5' (23m) 88.6' (27m) 11.7' (31m) 114.8' (35m) 128.' 141.1' B C (11m) C (15m) C C C C C C C C C C C (39m) C (43m) 8' 72 ###### 77 9, 1' 68 79, 74 77,3 79 7, ,1 12' 64 55, , , , , ,1 15' 58 37, , 73 35,2 73 4, , , , 79 37,5 2' 47 21, ,1 69 2, , , , , , , ,3 25' 32 14, 54 13, , , , , , , , ,3 77, , ,5 3' 46 8,6 58 8, ,3 64 9, ,9 69 1, ,2 72 1, , , , , ,9 35' 35 5,4 51 4,9 51 9, 59 6,3 59 9,6 65 7,2 65 9,9 69 7,7 69 1,1 72 8,1 72 1,3 74 9,4 76 8,7 4' 21 3,1 45 2,6 45 6,6 55 4, 55 7,2 61 4,9 61 7,6 5,4 7,8 69 5,8 69 7,9 71 7,1 74 6,3 45' 37 4,8 5 2,2 5 5,4 58 3,1 57 5,7 63 3,7 62 6, 4,1 6,1 69 5,3 72 4,6 5' 28 3,4 44 3,9 53 1,7 53 4,3 59 2,3 59 4,6 63 2,7 63 4,7 67 3,9 69 3,2 55' 11 2,3 38 2,8 49 3,2 55 3,4 6 1,6 6 3,6 64 2,8 67 2,1 6' 31 1,9 44 2,2 52 2,5 57 2,6 61 1,9 65' 38 1,5 48 1,7 54 1,9 7' 75' 8' 85' 9' 95' 1' 15' 11' 115' 12' 125' 13' 135' 14' D Telescoping conditions (%) 2nd boom 3rd boom 4th boom Top boom ON OUTRGGERS MN EXTENDED 8' 1-5/"(2.7m) SPREAD 36 o ROTATON,, LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON OUTRGGERS MN EXTENDED 8' 1-5/"(2.7m)SPREAD 36 o ROTATON A 36.1' 49.2' 62.3' (19m) C B (11m) B (15m) B 28.9' 9,9 42.' 2, 55.4' 2,2, A :Boom length in feet B :Load radius in feet C :Loaded boom angle ( o ) D :Minimum boom angle ( o ) for indicated length (no load) NOTE The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-C) is based on the standard number of parts of line listed in the chart. Standard number of parts of line for each boom length should be according to the following table. Boom length in feet 36.1' 36.1' to 49.2' 49.2' to 62.3' (meters) (11m) (11m to 15m) (15m to 19m) Telescoping, 62.3' to 141.1' (19m to 43m), Single top Jib, Number of parts of line

14 WARNNG AND OPERATNG NSTRUCTONS FOR LFTNG CAPACTES GENERAL 1. RATED LFTNG CAPACTES apply only to the machine as 9. When boom length is between values listed, refer to the originally manufactured and normally equipped by TADANO rated lifting capacities of the next longer and next shorter LTD. Modifications to the machine or use of optional booms for the same radius. The lesser of the two rated lifting equipment other than that specified can result in a reduction capacities shall be used. of capacity. 1. When making lifts at a load radius not shown, use the next 2. Hydraulic cranes can be hazardous if improperly longer radius to determine allowable capacity. operated or maintained. Operation and maintenance of this 11. Load per line should not exceed 12,3 lbs. (5,6kg) for machine must be in compliance with information in the main hoist and auxiliary hoist. Operation and Maintenance Manual supplied with 12. Check the actual number of parts of line with LOAD MOMENT the crane. f this manual is missing, order a replacement NDCATOR (AML-C) before operation. Maximum lifting through the distributor. capacity is restricted by the number of parts of line of LOAD 3. The operator and other personnel associated with this MOMENT NDCATOR (AML-C). Limited capacity is as machine shall fully acquaint themselves with the latest determined from the formula, Single line pull for main hoist American National Standards nstitute (ANS) safety 12,3 lbs.(5,6kg) x number of parts of line. standards for cranes. 13. The boom angle before loading should be greater to account for deflection. For rated lifting capacities, the loaded boom SET UP angle and the load radius is for reference only. 1. Rated lifting capacities on the load chart are the maximum 14. The 36.1' (11.m) boom length capacities are based on boom allowable crane capacities. They are based on the machine fully retracted. f not fully retracted [less than 49'(15.m) standing level on firm supporting surface under ideal job boom length], use the rated lifting capacities for the 49' (15.m) conditions. Depending on the nature of the supporting boom length. surface, it may be necessary to have structural supports 15. Extension or retraction of the boom with loads may be under the outrigger floats or tires to spread the loads to a attempted within the limits of the RATED LFTNG CAPACTES. larger surface. The ability to telescope loads is limited by hydraulic pressure, 2. For outrigger operation, outriggers shall be properly extended boom angle, boom length, crane maintenance, etc. with tires free of supporting surface before operating crane.. For lifting capacity of single top, reduce the rated lifting capacities of relevant boom according to a weight reductions OPERATON for auxiliary load handling equipment. Capacities of single top 1. Rated lifting capacities have been tested to and meet shall not exceed 12,3 lbs. (5,6kg) including main hook. minimum requirements of SAE J3-Cantilevered Boom 17. When base jib or top jib or both jib removing, jib state switch Crane Structures Method of Test. select removed. 2. Rated lifting capacities do not exceed 85 % of the tipping 18. When erecting and stowing jib, be sure to retain it by hand or by load on outriggers fully extended as determined by SAE other means to prevent its free movement. J765-Crane Stability Test Code. 19. Use "ANT-TWO BLOCK" disable switch when erecting and Rated lifting capacities for partially extended outriggers are stowing jib and when stowing hook block. While the switch is determined from the formula, Rated Lifting Capacities pushed, the hoist does not stop, even when overwind condition =(Tipping Load -.1 x Tip Reaction)/1.25. occurs. 3. Rated lifting capacities above bold lines in the chart are 2. For boom length with.2' (1.1m) jib, rated lifting capacities are based on crane strength and those below, on its stability. determined by loaded boom angle only in the column headed They are based on actual load radius increased by boom "141.1' (43.m) boom +.2' (1.1m) jib". deflection. For boom length with 58.1' (17.7 m) jib, rated lifting capacities 4. The weight of handling device such as hook blocks, slings, are determined by loaded boom angle only in the column etc., must be considered as part of the load and must be headed "141.1' (43.m) boom ' (17.7m) jib". deducted from the lifting capacities. For angles not shown, use the next lower loaded boom angle 5. Rated lifting capacities are based on freely suspended loads to determine allowable capacity. and make no allowance for such factors as the effect of wind, 21. When lifting a load by using jib (aux. winch) and boom (main sudden stopping of loads, supporting surface conditions, hoist) simultaneously, do the following: inflation of tires, operating speeds, side loads, etc. Side pull h Enter the operation status as jib operation, not as boom on the boom or jib is extremely dangerous. operation. 6. Rated lifting capacities do not account for wind on lifted load h Before starting operation, make sure that mass of load is or boom. We recommend against working under the condition within rated lifting capacity for jib. that the load is out of control due to a strong wind.during boom lift, consider that the rated lifting capacity is reduced by DEFNTONS 5% when the wind speed is 2mph(9m/s) to 27mph(12m/s); 1. Load Radius: Horizontal distance from a projection of the axis reduced by 7% when the wind speed is 27mph(12m/s) to of rotation to supporting surface before loading to the center of 31mph(14m/s).f the wind speed is 31mph(14m/s) or over, the vertical hoist line or tackle with load applied. stop operation. During jib lift, stop operation if the wind speed 2. Loaded Boom Angle: The angle between the boom base is 2mph(9m/s) section and the horizontal, after lifting the rated lifting capacity 7. Rated lifting capacities at load radius shall not be exceeded. at the load radius. Do not tip the crane to determine allowable loads. 3. Working Area: Area measured in a circular arc about the 8. Do not operate at boom lengths, radii, or boom angle, where centerline of rotation. no capacities are shown. Crane may overturn without any 4. Freely Suspended Load: Load hanging free with no direct load on the hook. external force applied except by the hoist line. 5. Side Load: Horizontal side force applied to the lifted load either on the ground or in the air. 14

15 GR-75XL RATED LFTNG CAPACTES (N POUNDS) ON RUBBER A Stationary Creep Over Front 36 o Rotation Over Front 36.1' 62.3' 88.6' 36.1' 62.3' 88.6' 36.1' 62.3' 88.6' B C (11m) C (19m) C (27m) C (11m) C (19m) C (27m) C (11m) C (19m) C (27m) 1' 68 65, 68 41, 68 51, 12' 64 6, 64 29, 64 44, 15' 59 5, 73 35, 58 2, 73 22, 58 36, 73 35, 2' 48 34, 69 35, 47 12, 68 14, 72 1, 48 27, 68 28, 25' 32 23, 63 25, 73 22, 7,5 63 9,5 69 7, 32 21, 63 22, 73 22, 3' 58 18, 69 19, 58 6,5 65 5, 58 17, 69 18, 35' 51 14, 65 15, 51 4,5 61 3, , 65 14, 4' 45 11, 62 12, 46 3, 57 2,3 45 1, 61 11, 45' 38 8, 58 9,5 37 7,5 57 9, 5' 28 6, 54 7,5 28 5,5 53 7, 55' 11 4,5 49 6, 11 4, 49 5,5 6' 44 5, 44 4,5 65' 39 4, 39 3,5 7' 3, 2,5 D Telescoping conditions (%),,, 2nd boom 3rd boom 4th boom Top boom LFTNG CAPACTES AT ZERO DEGREE BOOM ANGLE ON RUBBER OPERATON A Stationary Creep Over Front 36 o Rotation Over Front 36.1' 62.3' 88.6' 36.1' 36.1' 62.3' 88.6' C B (11m) B (19m) B (27m) B (11m) B (11m) B (19m) B (27m) 28.9' 17,6 55.4' 4,4 81.7' ' 5,1 28.9' 17,2 55.4' 4, 81.7' 7 A :Boom length in feet B :Load radius in feet C :Loaded boom angle ( o ) D :Minimum boom angle ( o ) for indicated length (no load) NOTE: The lifting capacity data stored in the LOAD MOMENT NDCATOR (AML-C) is based on the standard number of parts of line listed in the chart. Standard number of parts of line for rubber operation should be according to the following table. Boom length in feet 36.1' 36.1' to 88.6' Single top (meters) (11m) (11m to 27m) Jib Number of parts of line WARNNG AND OPERATNG NSTRUCTONS FOR ON RUBBER LFTNG CAPACTES 1. Rated lifting capacities on rubber are in pounds and do not exceed 6. Over front operation shall be performed within two degrees in front of 75 % of tipping loads as determined by SAE J765-Crane Stability chassis. Test Code. 7. On rubber lifting with "jib" is not permitted. Maximum permissible 2. Rated lifting capacities shown in the chart are based on condition boom length is 88.6 ft. (27.m). that crane is set on firm level surfaces with axle oscillation lockout 8. When making lift on rubber stationary, set parking brake. applied. Those above bold lines are based on tire capacity and 9. For creep operation, boom must be centered over front of machine, those below, on crane stability. They are based on actual load swing lock engaged, and load restrained from swinging. Travel slowly radius increased by tire deformation and boom deflection. and keep the lifted load as close to the ground as possible, and 3. f the axle oscillation lockout cylinders contain air, the axle will not especially avoid any abrupt steering, accelerating or braking. be locked completely and rated lifting capacities may not be 1. Do not operate the crane while carrying the load. obtainable. Bleed the cylinders according to the operation safety 11. Creep is motion for crane not to travel more than 2 ft. (6 m) in any and maintenance manual. 3 minute period and to travel at the speed of less than 1 mph 4. Rated lifting capacities are based on proper tire inflation, capacity (1.6km/h). and condition. Damaged tires are hazardous to safe operation of 12. For creep operation, choose the drive and proper gear crane. according to the road or working condition. 5. Tires shall be inflated to correct air pressure. Tires Air Pressure PR 6 psi (4.2 kgf/cm2) PR 64 psi (4.5 kgf/cm2) 15

16 WARNNG AND OPERATNG NSTRUCTONS FOR USNG THE LOAD MOMENT NDCATOR (AML-C) 1. When operating crane on outriggers: h When a load is lifted in the front position and then swung h Set P.T.O. switch to "ON". to the side area, make sure the value of the LOAD h Press the outrigger select key to register for the MOMENT NDCATOR(AML-C) is below the 36 o lifting outrigger operation. Press the register key, then the outrigger capacity. indicative symbol changes from flashing to a solid light. (2) For creep operation. h Press the lift select key to select the lift status that h The creep capacities are attainable only when boom is corresponds to the actual boom configuration. in the straight forward position of chassis and the over Each time the lift select key is pressed, the status changes. front position symbol is on. f boom is not in the straight Press the register key to register the lift status, then the lift forward position of chassis, never lift load. indicative symbol changes from flashing to a solid light. 3. A swing does not automatically stop even if the crane h when mounting and stowing jib, select the jib set status. becomes overloaded. (the jib state indicative symbol will be flashing.) 4. During crane operation, make sure that the displays on front 2. When operating crane on rubber: panel are in accordance with actual operating conditions. h Set P.T.O. switch to "ON". 5. The displayed values of LOAD MOMENT NDCATOR h Press the outrigger select key. The on-tire (AML-C) are based on freely suspended loads and make no indicative symbol comes on. Each time the outrigger allowance for such factors as the effect of wind, sudden select key is pressed the status changes. Select the creep stopping of loads, supporting surface conditions, inflation of operation, the on-tire indicative symbol flicker. tire, operating speed, side loads, etc. h Press the lift select key to register the boom or single top For safe operation, it is recommended when extending and lift. lowering boom or swinging, lifting loads shall be However, pay attention to the following. appropriately reduced. (1) For stationary operation. 6. LOAD MOMENT NDCATOR (AML-C) is intended as an aid h The front capacities are attainable only when the over front to the operator. Under no condition should it be relied upon position symbol comes on. When the boom is more than to replace use of capacity charts and operating instruction. 2 degrees from centered over front of chassis, 36 o Sole reliance upon LOAD MOMENT NDCATOR (AML-C) capacities are in effect. aids in place of good operating practice can cause an accident. The operator must exercise caution to assure safety. GR-75XL Axle weight distribution chart Base machine Remove: ton(5.6metric ton) hook ball 2. 75ton(68metric ton) hook block 3. Top jib 4. Base jib 5. Auxiliary lifting sheave 6. Removable Counterweihgt (with Auxiliary Hoist&wire) Pounds Kilograms GVW Front Rear GVW Front Rear 97,62 49,65 47,97 44,28 22,52 21, ,3-2,31 1, , ,91-3,27 1, , ,5 5,51-18,1-5,67 2,498-8,8 TADANO AMERCA CORPORATON 4242 West Greens Road. Houston, Taxas, 77 U.S.A. PHONE: (281) FAX: (281) Form No. TAC-GR75XL