PULVERIZERS 20A148 20A160 SU172 SU184 SU172BT SU184BT OPERATOR'S MANUAL MAN0130. Rev. 8/1/2013. Tested. Proven. Unbeatable.

Transcription

1 MAN0130 Rev. 8/1/2013 PULVERIZERS 20A148 20A160 SU172 SU184 SU172BT SU184BT Tested. Proven. Unbeatable. OPERATOR'S MANUAL

2 TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods dealer. Read manual instructions and safety rules. Make sure all items on the Dealer s Pre-Delivery and Delivery Check Lists in the Operator s Manual are completed before releasing equipment to the owner. The dealer must complete the online Product Registration form at the Woods Dealer Website which certifies that all Dealer Check List items have been completed. Dealers can register all Woods product at dealer.woodsequipment.com under Product Registration. Failure to register the product does not diminish customer s warranty rights. TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be obtained from your dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Observe all safety information in this manual and safety decals on the equipment. For service, your authorized Woods dealer has trained mechanics, genuine Woods service parts, and the necessary tools and equipment to handle all your needs. Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided: Model: Date of Purchase: Serial Number: (see Safety Decal section for location) Provide this information to your dealer to obtain correct repair parts. Throughout this manual, the term NOTICE is used to indicate that failure to observe can cause damage to equipment. The terms CAUTION, WARNING, and DANGER are used in conjunction with the Safety-Alert Symbol (a triangle with an exclamation mark) to indicate the degree of hazard for items of personal safety. 2 Introduction Gen l (Rev. 12/5/2011)

3 TABLE OF CONTENTS INTRODUCTION INSIDE FRONT COVER GENERAL INFORMATION SPECIFICATIONS SAFETY RULES SAFETY DECALS OPERATION OWNER SERVICE ASSEMBLY DEALER CHECK LISTS PARTS LISTS 20A148 & 20A160 PULVERIZERS SU172 & SU184 PULVERIZERS SU172BT & SU184BT PULVERIZERS SECOND ROLLER KITS (OPTIONAL) HITCH KIT FOR 20A148 (OPTIONAL) BOLT TORQUE CHART BOLT SIZE CHART & ABBREVIATIONS PRODUCT WARRANTY REPLACEMENT PARTS WARRANTY INSIDE BACK COVER! LEA EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. GENERAL INFORMATION The purpose of this manual is to assist you in operating and maintaining your Pulverizer. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation. (Rev. 4/29/2005) MAN0130 (8/24/01) The illustrations and data used in this manual were current at the time of printing. However, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification. Throughout this manual, references are made to right and left directions. These are determined by standing behind the tractor facing the direction of forward travel. Introduction 3

4 SPECIFICATIONS Specification 20A148 20A160 Working width 48" 60" Overall width 54" 66" Height to top of A-frame 36" 36" Depth, front to back 28-1/2" 28-1/2" Weight 480 lbs 550 lbs Roller diameter 6-5/8" O.D. 6-5/8" O.D. Roller pins 3/8" dia. x 1-1/8" long (hardened pins) 3/8" dia. x 1-1/8" long (hardened pins) Scarifier teeth Hardened 5/8" sq. Hardened 5/8" sq. Number of teeth 9 Front 8 Rear 11 Front 10 Rear Bearings 1" self-aligning 1" self-aligning Frame 10" wide flange H-beam (49 lbs-ft) 10" wide flange H-beam (49 lbs-ft) Tractor hitch requirement Category 1 Category 1 Tractor horsepower requirement 45 HP maximum 45 HP maximum 4 Introduction MAN0130 (8/24/01)

5 SPECIFICATIONS Specification SU172 SU172BT SU184 SU184BT Working width 72" 72" 84" 84" Overall width 78" 78" 90" 90" Height to top of A-frame 36" 36" 36" 36" Depth, front to back 30-1/2" 30-1/2" 30-1/2" 30-1/2" Weight 715 lbs 735 lbs 784 lbs 805 lbs Roller diameter 6-5/8" OD 6-5/8" OD 6-5/8" OD 6-5/8" OD Roller pins 3/8" dia. x 1-1/8" long (hardened pins) 3/8" dia. x 1-1/8" long (hardened pins) 3/8" dia. x 1-1/8" long (hardened pins) 3/8" dia. x 1-1/8" long (hardened pins) Scarifier teeth Hardened 5/8" sq. Hardened 1/2" x 2" x 13" reversible Hardened 5/8" sq. Hardened 1/2" x 2" x 13" reversible Number of teeth 14 Front 13 Rear 14 Front 13 Rear 16 Front 15 Rear 16 Front 15 Rear Bearings 1" self-aligning 1" self-aligning 1" self-aligning 1" self-aligning Frame 12" wide flange H-beam (53 lbs-ft) 12" wide flange H-beam (53 lbs-ft) 12" wide flange H-beam (53 lbs-ft) 12" wide flange H-beam (53 lbs-ft) Tractor hitch requirement Category 1 Category 1 Category 1 Category 1 Tractor horsepower requirement 65 HP maximum 65 HP maximum 65 HP maximum 65 HP maximum MAN0130 (8/24/01) Introduction 5

6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgement, and proper training of personnel involved in the operation, transport, maintenance, and storage of equipment. It has been said, The best safety device is an informed, careful operator. We ask you to be that kind of operator. TRAINING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call ) Failure to follow instructions or safety rules can result in serious injury or death. If you do not understand any part of this manual and need assistance, see your dealer. Know your controls and how to stop engine and attachment quickly in an emergency. Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions. Never allow children or untrained persons to operate equipment. PREPARATION Check that all hardware is properly installed. Always tighten to torque chart specifications unless instructed otherwise in this manual. Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Make sure attachment is properly secured, adjusted, and in good operating condition. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in locked up position at all times. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate. OPERATION Do not operate or transport equipment while under the influence of alcohol or drugs. Always comply with all state and local lighting and marking requirements. Operate only in daylight or good artificial light. Keep bystanders away from equipment. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in locked up position at all times. Never allow riders on power unit or attachment. Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. Look down and to the rear and make sure area is clear before operating in reverse. Use extreme care when working close to fences, ditches, other obstructions, or on hillsides. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. 6 Safety Landscape Misc. SR (Rev. 5/16/2003)

7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. TRANSPORTATION Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, front tractor wheels could raise up resulting in loss of steering. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate. Always comply with all state and local lighting and marking requirements. Never allow riders on power unit or attachment. Do not operate or transport on steep slopes. Do not operate or transport equipment while under the influence of alcohol or drugs. MAINTENANCE Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Make sure attachment is properly secured, adjusted, and in good operating condition. Before dismounting tractor or performing any service or maintenance, lower attachment to ground, turn off engine, set parking brake, operate valve levers to release any hydraulic pressure, and remove key. Do not modify or alter or permit anyone else to modify or alter the equipment or any of its components in any way. Never perform service or maintenance with engine running. Keep all persons away from operator control area while performing adjustments, service, or maintenance. Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service. Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.) STORAGE Block equipment securely for storage. Keep children and bystanders away from storage area. Landscape Misc. SR (Rev. 5/16/2003) Safety 7

8 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 3 2 MODEL NO. SERIAL NO. 5 Woods Equipment Company Oregon, Illinois, U.S.A. 1 1 Serial Number Plate ALL MODELS WARNING TO AVOID SERIOUS INJURY OR DEATH: Read Operator's Manual before operating, servicing or 5 repairing equipment. Follow all safety rules and instructions. (Manuals are available from dealer or call ) Operate from tractor seat only. Lower equipment to ground, stop engine, remove key and set brake before dismounting tractor. Never allow children or untrained persons to operate equipment. Never allow riders. Keep bystanders away from equipment during operation. Keep all shields in place and in good condition. Do not transport towed or semi-mounted units over 20 mph. FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN INJURY OR DEATH. 20A148 20A D 4 (CENTER) CD5935-Var WARNING FALLING OFF CAN RESULT IN BEING RUN OVER. Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in locked up position at all times. Buckle Up! Keep seat belt securely fastened. Allow no riders. RAISED IMPLEMENT CAN DROP AND CRUSH. Never go underneath raised implement which can drop from equipment or tractor 3-point hitch hydraulic leak down, hydraulic system failures, movement of control levers or mechanical linkage failures. Service work does not require going underneath implement. Read manual instructions. FALLING OFF OR GOING UNDERNEATH IMPLEMENT CAN RESULT IN SERIOUS INJURY OR DEATH C 8 Safety (Rev. 4/29/2005) MAN0130 (8/17/01)

9 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! 5 WARNING ENTANGLEMENT AND FALLING HAZARD Do not stand on rollers while machine is in operation or parked. Failure to follow these instructions could result in serious injury or death SU172 SU184 4 CD5925-Var WARNING 5 CRUSHING AND PINCHING HAZARD Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts could be crushed or pinched between tractor and implement. Operate tractor controls from tractor seat only. Do not stand between tractor and implement when tractor is in gear. Make sure parking brake is engaged before going between tractor and implement. Stand clear of machine while in operation or when it is being raised or lowered. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH A SU172BT SU184BT 4 CD5935-Var BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through very small scratches or under edges of decals causing them to peel or come off. Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at or in the United States and Canada call (Rev. 4/29/2005) MAN0130 (8/17/01) Safety 9

10 OPERATION The operator is responsible for the safe operation of this pulverizer. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on pages 6 through 9. WARNING Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS systems in locked up position at all times. Never allow children or untrained persons to operate equipment. Keep bystanders away from equipment. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. CAUTION Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head. PRE-OPERATION CHECK LIST (OWNER'S RESPONSIBILITY) Review and follow all safety rules and safety decal instructions on pages 6 through 9. Check that equipment is properly and securely attached to tractor. Check that all safety decals are installed and in good condition. Replace if damaged. Do not allow riders. Check that all hardware is properly installed and secured. Check all lubrication points and grease as instructed in Lubrication Information, page 12. Make sure tractor ROPS or ROPS CAB and seat belt are in good condition. Keep seat belt securely fastened during operation. GENERAL INFORMATION The pulverizer is designed to immediately follow rough grading by a motor grader or bulldozer. The pulverizer is also an excellent companion tool to a rollover, box-type scraper or utility blade for the purpose of scarifying hard clay or loamy soils. The pulverizer may be used with either constant draft control or implement position control stops. Normally, it is better to use implement position control during the initial portion of the job, especially when the pulverizer is operated in reverse. When the finished grade becomes more established, switching to control draft will speed up the work. Experiment with both settings to determine the best method for your particular application. ATTACHING PULVERIZER TO TRACTOR 1. Place the pulverizer on a level, dry area, positioned behind the tractor. Connect pulverizer mounting pins to tractor lower arms. 2. Secure mounting pins to lift arms with 7/16 x 1-3/4" lynch pins. 3. Connect the tractor top link to the pulverizer upper mast. NOTE: Initial adjustment of the top link must be made on a level surface. 4. Rest scarifier teeth on the ground and level the pulverizer by extending or retracting the top link. 5. Carefully operate the pulverizer through the tractor s full lift range, making sure pulverizer does not come into contact with any tractor component. 6. Adjust top link if necessary. ADJUSTING TOP LINK Top link adjustment is critical to the pulverizer s performance. The unit can be pitched either forward or rearward, depending on the soil conditions and job requirements. You will need to experiment to determine the best setting for the job being performed. For normal conditions, the pulverizer should be adjusted in a level position. This is especially useful when finish leveling and back filling. When excessive debris or hard scarifying conditions exist, pitch the pulverizer forward to optimize performance. Pitching the pulverizer rearward will optimize roller action and assist in over-seeding applications. 10 Operation MAN0130 (Rev. 11/11/2005)

11 ADJUSTING ROLLER SPRING The roller springs are assembled loose at the factory for normal operating conditions. For abnormal operating conditions, you may want to make the adjustments in the chart below. Compressing springs 1 inch will put 100 pounds of pressure on the primary roller. Adjusting secondary roller springs 1/2 inch will put an additional 100 pounds of pressure on that roller. SCARIFIER TEETH SETTING The 8" scarifying teeth are set at the factory at 3-1/2" below the H-beam flange. Do not lower the spikes, this will result in additional strain and cause excess scarifying before leveling and grading. CONDITION Hard, tight clay Loamy, loose soil Loose, sandy soil ADJUSTMENT Additional spring tension No adjustment Run with no tension on roller OPERATING TIPS DIRECTION ACTION APPLICATION Forward Straight line General purpose pulverizing Long arcs Short, tight arcs For seeding, dressing out soil during final seedbed preparation, and stockpiling debris into a single pile For hard, tight clay conditions; centrifugal force applied to roller pins will allow faster pulverizing Reverse Clod breaking & pulverizing Improves clod breaking, especially with SU models Leveling Backfilling Scarifier teeth promote even, ideal seedbed Light backfilling around foundations and sidewalks PROCEDURE ACTION ADVANTAGE Grading Grade at 90 angles Helps eliminate swells and valleys. Establishes grade lines more quickly Humps Pull humps into low places close to the area being pulverized Saves time (Rev. 8/1/2013) MAN0130 (Rev. 11/11/2005) Operation 11

12 OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. WARNING NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Service work does not require going underneath. Read Operator's Manual for service instructions or have service performed by a qualified dealer. Keep all persons away from operator control area while performing adjustments, service, or maintenance. WARNING Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt. CAUTION Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head. LUBRICATION INFORMATION The roller bearings are self-aligning, dust-proof ball bearings. Use any good grade of multi-purpose grease and lubricate as needed. Figure 1 shows lubrication locations and frequency. Harsh conditions may require more frequent lubrication. CD5925-Var 8 (BOTH SIDES) Figure 1. Lubrication Points 12 Owner Service MAN0130 (Rev. 11/11/2005)

13 CLEANING After Each Use Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine. Inspect machine and replace worn or damaged parts. Replace any safety decals that are missing or not readable. Periodically or Before Extended Storage Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine. Remove the remainder using a low-pressure water spray. 1. Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface. 2. Be careful when spraying near chipped or scratched paint as water spray can lift paint. 3. If a pressure washer is used, follow the advice of the pressure washer manufacturer. Inspect machine and replace worn or damaged parts. Sand down scratches and the edges of areas of missing paint and coat with spray paint of matching color (purchase from your dealer). Replace any safety decals that are missing or not readable (supplied free by your dealer). See Safety Decals section for location drawing. NOTES MAN0130 (Rev. 11/11/2005) Owner Service 13

14 ASSEMBLY SECOND ROLLER KIT (OPTIONAL) 1. From right and left roller hinges, remove 5/8" cap screw (15), lock washer (17), and hex nut (16). 2. Roll the roller kit forward until right and left roller arms (4, 5 - not shown) from base unit are inserted into right and left roller hinges (2, 3 - not shown). 3. Align holes and reinstall cap screw, lock washer, and hex nut in each side. 1. Remove sleeve, nut, washers and bolt from the lower hole in the upper third point area. Re-install in the upper hole, Figure 4. Torque to 297 lbs-ft (403 N-m) Roller hinge, right 4. Roller kit arm, right 15. 5/8 NC x 2-1/4 Cap screw 16. 5/8 NC Hex nut 17. 5/8 Heavy lock washer Figure 2. Roller Kit Installation (Right side shown) HITCH KIT (OPTIONAL) NOTE: Only fits 20A148 pulverizers made after serial number This hitch kit allows higher 3- point hitch lift height on sub-compact tractors. 4, 5, 6 Figure 4. Upper Hitch Hardware Installation 2. Remove hitch pins from the pulverizer. 3. Place the slot of the hitch plate over the I-beam with the bend toward the inside. 4. Secure into position using cap screw (4), lock washer (5), and hex nut (6). The head of the cap screw must be on the inside of the A-frame. 5. Insert hitch pin into lower holes. 6. Torque hardware to 474 lbs-ft (642 N-m). 7. Repeat for opposite side. 1 SLOT Top link sleeve & hardware 2. Hitch plate, right 3. Hitch plate, left 3 4, 5, /8 NC x 2-1/2 Cap screw GR5 5. 7/8 Lock washer 6. 7/8 NC Hex nut CD6550-var Figure 5. Hitch Plate Installation (Right side shown) 2 Figure 3. Hitch Kit Installation - 20A148 Only (Rev. 4/29/2005) 14 Assembly WPMAN0130 (8/24/01)

15 DEALER CHECK LISTS The Pulverizer is completely assembled at the factory for your convenience. Before delivering it to the customer, complete the following check lists. PRE-DELIVERY CHECK LIST (DEALER S RESPONSIBILITY) Inspect the equipment thoroughly before delivering it to the customer: Check that all safety decals are installed and in good condition. Replace if damaged. Check all bolts to be sure they are properly torqued. Check that all cotter pins and safety pins are properly installed. Replace if damaged. DELIVERY CHECK LIST (DEALER S RESPONSIBILITY) Present Operator's Manual and request that customer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed. Show customer how to make adjustments. Instruct customer how to lubricate and explain importance of lubrication. Show customer the safe, proper procedures to be used when mounting, dismounting, and storing equipment. Explain to customer the potential crushing hazards of going underneath raised equipment. Instruct customer that service work does not require going underneath unit and never to do so. Add wheel weights, ballast in front tires, and/or front tractor weight to enhance front end stability. A minimum 20% of tractor and equipment gross weight must be on the front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. Do not estimate! (Rev. 4/29/2005) MAN0130 (8/24/01) Dealer Check Lists 15

16 20A148 & 20A160 PULVERIZERS 24 SAFETY DECAL SET 25 COMPLETE DECAL SET CD5931A REF PART QTY DESCRIPTION 1 ** 1 20A160 H-BEAM -or- 1 ** 1 20A148 H-BEAM ROLLER 60" -or ROLLER 48" ROLLER ARM RETAINER ROLLER ARM RIGHT ROLLER ARM LEFT * 2 WASHER, 3/8 FLAT NUT, JAM 3/4 NC 9 20A111 2 SPRING STUD (LONG) 10 20A125 2 SPRING (LONG) 11 20A " BEARING W/HOUSING PIN, CLEVIS 3/8 X 2-1/ * 6 3/8 X 2 SPIROL PIN * 8 NUT, HEX 3/8 NC PLTD * 8 WASHER, 3/8 LOCK * 8 HHCS, 3/8 NC X 1-1/2 GR5 17 SU105 2 CAT 1 DRAWBAR PIN WITH LYNCH PIN * 2 3/16 X 1 COTTER PIN 20 20A122 AR 8" SPIKE 21 20A108 AR U-BOLT, ZINC REF PART QTY DESCRIPTION * AR WASHER, 7/16 STD D LOCK AR NUT, HEX 7/16 NF DECAL SET, SAFETY DECAL SET COMPLETE 26a SLEEVE -.81 X 1.25 X b * 1 HHCS, 3/4 NC X 4 GR5 26c 1257 * 2 WASHER, 3/4 FLAT 26d 2371 * 1 NUT, LOCK 3/4 NC NS PIN REPLACEMENT SET * Standard hardware; obtain locally ** Not serviced separately NS Not shown AR As required 7 4 (Rev. 11/11/2005) 16 Parts MAN0130 (8/17/01)

17 SU172 & SU184 PULVERIZERS 24 SAFETY DECAL SET 1 25 COMPLETE DECAL SET CD5933A REF PART QTY DESCRIPTION 1 ** 1 84" BEAM SU -or- 1 ** 1 72" BEAM SU ROLLER 84" -or ROLLER 72" ROLLER ARM RETAINER ROLLER ARM RT ROLLER ARM LT * 2 WASHER, 3/8 FLAT NUT, JAM 3/4 NC 9 20A111 2 SPRING STUD (LONG) 10 20A125 2 SPRING (LONG) 11 20A " BEARING W/HOUSING PIN, CLEVIS 3/8 X 2-1/ * 6 3/8 X 2 SPIROL PIN * 8 NUT, HEX 3/8 NC PLTD * 8 WASHER, 3/8 LOCK * 8 HHCS, 3/8 NC X 1-1/2 GR5 17 SU105 2 CAT 1 DRAWBAR PIN WITH LYNCH PIN * 2 3/16 x 1 COTTER PIN 20 20A122 AR 8" SPIKE REF PART QTY DESCRIPTION 21 20A108 AR U-BOLT, ZINC * AR WASHER, 7/16 STD D LOCK AR NUT, HEX 7/16 NF DECAL SET, SAFETY DECAL SET COMPLETE 26a SLEEVE -.81 X 1.25 X b * 1 HHCS, 3/4 NC X 4 GR5 26c 1257 * 2 WASHER, 3/4 FLAT 26d 2371 * 1 NUT, LOCK 3/4 NC NS PIN REPLACEMENT SET * Standard hardware; obtain locally ** Not serviced separately NS Not shown AR As required (Rev. 11/11/2005) MAN0130 (8/17/01) Parts 17

18 SU172BT & SU184BT PULVERIZERS 24 SAFETY DECAL SET 25 COMPLETE DECAL SET CD5932A REF PART QTY DESCRIPTION 1 ** 1 84" BEAM SU BT -or- 1 ** 1 72" BEAM SU BT ROLLER 84" -or ROLLER 72" ROLLER ARM RETAINER ROLLER ARM RIGHT ROLLER ARM LEFT * 2 WASHER, 3/8 FLAT NUT, JAM 3/4 NC 9 20A111 2 SPRING STUD (LONG) 10 20A125 2 SPRING (LONG) 11 20A " BEARING W/HOUSING PIN, CLEVIS 3/8 X 2-1/ * 6 3/8 X 2 SPIROL PIN * 8 NUT, HEX 3/8 NC PLTD * 8 WASHER, 3/8 LOCK * 8 HHCS, 3/8 NC X 1-1/2 GR5 17 SU105 2 CAT 1 DRAWBAR PIN WITH LYNCH PIN * 2 3/16 X 1 COTTER PIN AR BIG TOOTH REF PART QTY DESCRIPTION 21 20A108 AR U-BOLT, ZINC * AR WASHER, 7/16 STD D LOCK AR NUT, HEX 7/16 NF DECAL SET, SAFETY DECAL SET COMPLETE 26a SLEEVE -.81 X 1.25 X b * 1 HHCS, 3/4 NC X 4 GR5 26c 1257 * 2 WASHER, 3/4 FLAT 26d 2371 * 1 NUT, LOCK 3/4 NC NS PIN REPLACEMENT SET * Standard hardware; obtain locally ** Not serviced separately NS Not shown AR As required (Rev. 11/11/2005) 18 Parts MAN0130 (8/17/01)

19 , , & SECOND ROLLER KITS (OPTIONAL) CD5934 REF PART QTY DESCRIPTION ROLLER 48" -or ROLLER 60" -or ROLLER 72" -or ROLLER 84" ROLLER HINGE RIGHT ROLLER HINGE LEFT ROLLER KIT ARM RIGHT ROLLER KIT ARM LEFT NUT, JAM 3/4 NC 7 20A920 2 BEARING * 2 HHCS, 3/8 NC X 2 GR PIN, CLEVIS 5/8 X 1-3/ * 8 NUT, HEX 3/8 NC PLTD * 8 WASHER, 3/8 LOCK * 8 HHCS, 3/8 NC X 1-1/2 GR5 13 SU228 2 SPRING STUD REAR REF PART QTY DESCRIPTION 14 SU229 2 SPRING REAR (SHORT) * 4 HHCS, 5/8 NC X 2-1/ * 4 NUT, HEX 5/8 NC PLATED * 4 WASHER, 5/8 HEAVY LOCK * 4 WASHER, 3/8 FLAT * 2 NUT, LOCK 3/8 NC * 2 WASHER, 5/8 STD SAE FLAT * 2 3/16 X 1 COTTER PIN * 2 3/8 X 2 SPIROL PIN NS PIN REPLACEMENT SET * Standard hardware; obtain locally ** Not serviced separately NS Not shown HITCH KIT (OPTIONAL) REF PART QTY DESCRIPTION A HITCH KIT, COMPLETE 1 1 TOP LINK SLEEVE & HARDWARE 2 ** 1 HITCH PLATE, BOLT-ON RH 3 ** 1 HITCH PLATE, BOLT-ON LH 4 * 2 HHCS, 7/8 NC X 2-1/2 GR5 5 * 2 WASHER, 7/8 LOCK 6 * 2 NUT, 7/8 NC HEX 1 Only for 20A148 Model after SN Allows higher 3-point hitch lift height on sub-compact tractors. * Standard hardware; obtain locally ** Not sold separately Pulverizer parts - not included in hitch kit (Rev. 4/29/2005) MAN0130 (8/17/01) 2 CD6550A 3 4, 5, & 6 Parts 19

20 BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96. A SAE SERIES TORQUE CHART SAE Grade 2 (No Dashes) SAE Bolt Head Identification SAE Grade 5 (3 Radial Dashes) SAE Grade 8 (6 Radial Dashes) A MARKING ON HEAD Diameter Wrench SAE 2 SAE 5 SAE 8 (Inches) Size lbs-ft N-m lbs-ft N-m lbs-ft N-m 1/4" 7/16" /16" 1/2" /8" 9/16" /16" 5/8" /2" 3/4" /16" 13/16" /8" 15/16" /4" 1-1/8" /8" 1-5/16" " 1-1/2" A METRIC SERIES TORQUE CHART Coarse Thread 8.8 Metric Grade 8.8 Metric Bolt Head Identification Fine Thread Metric Grade 10.9 A Marking on Head Marking on Head A Diameter & Diameter & Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9 Thread Pitch Wrench Thread Pitch (Millimeters) Size N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft (Millimeters) 6 x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x Typical Washer Installations Bolt Lock Washer Flat Washer 8/9/00 20 Appendix Bolt Torque & Size Charts (Rev. 3/28/2007)

21 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 3/8 1/2 5/8 3/4 7/8 IN MM Metric Bolt Thread Sizes 8MM 10MM 12MM 14MM 16MM 18MM AG... Agriculture ASABE... American Society of Agricultural & Biological Engineers (formerly ASAE) ASAE... American Society of Agricultural Engineers ATF... Automatic Transmission Fluid BSPP...British Standard Pipe Parallel BSPTM...British Standard Pipe Tapered Male CV...Constant Velocity CCW... Counter-Clockwise CW... Clockwise F... Female FT... Full Thread GA... Gauge GR (5, etc.)... Grade (5, etc.) HHCS...Hex Head Cap Screw HT... Heat-Treated JIC...Joint Industry Council 37 Degree Flare LH...Left Hand LT... Left m... Meter mm...millimeter M... Male ABBREVIATIONS MPa...Mega Pascal N...Newton NC...National Coarse NF...National Fine NPSM...National Pipe Straight Mechanical NPT... National Pipe Tapered NPT SWF...National Pipe Tapered Swivel Female ORBM... O-Ring Boss - Male P...Pitch PBY... Power-Beyond psi...pounds per Square Inch PTO... Power Take Off QD...Quick Disconnect RH...Right Hand ROPS... Roll-Over Protective Structure RPM...Revolutions Per Minute RT... Right SAE...Society of Automotive Engineers UNC...Unified Coarse UNF...Unified Fine UNS...Unified Special Bolt Torque & Size Charts (Rev. 3/28/2007) Appendix 21

22 Please Enter Information Below and Save for Future Reference. WARRANTY All Models Except Mow n Machine TM Zero-Turn Mowers Date Purchased: From (Dealer): Model Number: Serial Number: Woods Equipment Company ( WOODS ) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser. The warranty periods for specific parts or conditions are listed below: Part or Condition Warranted Gearbox components Blade spindles Rust-through Model Number All units invoiced after 4/30/2012 BW1260, BW1620, BW1800, BW1260X, BW1800X, BW2400 BW240HD, BW180HD, BW180HB, BW126HB, BW126XHD, BW180XHD BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X, DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240, BW126X, BW180X PHD25, PHD35, PHD65, PHD95, DS96, DS120, RCC42, RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, S30CD BW15LH, TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204 RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44, HC48, HC54, HC60, HC72 RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204 BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB, BW180HD, BW1260, BW1800, BW240, BW240HD, DS1260, DSO1260, DS1440, TS1680 Duration (from date of delivery to the original purchaser) 6 years 3 years (1 year if used in rental or commercial applications) 3 years 10 years Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other than those obtainable through WOODS. This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty. WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers. WOODS obligation under this Warranty is limited to, at WOODS option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss. This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts. No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regarding warranty service and locations may be obtained by contacting: Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois USA tel fax F-3079 (Rev. 3/2/2012)

23 WARRANTY (Replacement Parts For All Models Except Mow n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company ( WOODS ) warrants this product to be free from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the product to the original purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a period of 12 months. Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty. WOODS obligation under this Warranty is limited to, at WOODS option, the repair or replacement, free of charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss. This Warranty is subject to any existing conditions of supply which may directly affect WOODS ability to obtain materials or manufacture replacement parts. No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty. Answers to any questions regarding warranty service and locations may be obtained by contacting: Woods Equipment A Blount International Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois tel fax woodsequipment.com 2013 Woods Equipment Company. All rights reserved. Woods and the Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice. F-8494 (Rev. 2/5/2013)

24 PART NO. MAN0130 Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000 Oregon, Illinois tel fax Woods Equipment Company. All rights reserved. WOODS, the Woods logo, Gill, and "Tested. Proven. Unbeatable." are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.