O P E R A T O R S M A N U A L BOX BLADES BB5060 BB5048L BB5072 BB5060L BB5084 BB TITE (Rev. 10/14/2011)

Transcription

1 O P E R A T O R S M A N U A L BOX BLADES BB5060 BB5072 BB5048L BB5060L BB5084 BB5096 5TITE (Rev. 10/14/2011)

2 TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Frontier dealer. Read manual instructions and safety rules. Make sure all items on the Preparation Check List in the Operator s Manual are completed before releasing equipment to the owner. TO THE OWNER: Read this manual before operating your Frontier equipment. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustments and operating procedures before attempting to operate the equipment. Replacement manuals can be obtained from your selling dealer. The equipment you have purchased has been carefully engineered and manufactured to provide dependable and satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified. Please observe all safety information in this manual and safety decals on the equipment. For service, your authorized Frontier dealer has trained mechanics, genuine Frontier service parts, and the necessary tools and equipment to handle all of your service needs. Use only genuine Frontier service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces provided: Model Date of Purchase Serial Number: (see Safety Decal section for loaction) Provide this information to your dealer to obtain correct repair parts. Throughout this manual, the term IMPORTANT is used to indicate that failure to observe procedures can cause damage to equipment. The terms CAUTION, WARNING and DANGER are used in are used in conjunction with the Safety-Alert Symbol, (a triangle with an exclamation mark), to indicate the degree of hazard for items of personal safety. This is the safety alert symbol. it is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. WARNING CAUTION IMPORTANT NOTE Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury. Is used to address practices not related to personal injury. Indicates helpful information. 2 Introduction

3 TABLE OF CONTENTS INTRODUCTION... 2 GENERAL INFORMATION... 3 SPECIFICATIONS... 4 SAFETY RULES DEALER CHECK LISTS... 7 SAFETY DECALS OPERATION OWNER SERVICE PARTS LIST BOLT TORQUE CHART BOLT SIZE CHART & ABBREVIATIONS All information, illustrations and specifications in this manual are based on the latest information available at the time of publication. The right is reserved to make changes at any time without notice. This Operator s Manual should be regarded as part of the machine. Suppliers of both new and second-hand machines must make sure that this manual is provided with the machine. The purpose of this manual is to assist you in operating and maintaining your Box Blade. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. These instructions have been compiled from extensive field experience and engineering data. Some information may be general in nature, due to unknown and varying operating conditions. However, through experience and these instructions, you should be able to develop procedures suitable to your particular situation. GENERAL INFORMATION The illustrations and data used in this manual were current at the time of printing. However, due to possible inline production changes, your machine may vary slightly in detail. We reserve the right to redesign and change the machines as may be necessary without notification. Throughout this manual, references are made to right and left directions. These are determined by standing behind the tractor facing the direction of forward travel. General Information 3

4 Dimensions SPECIFICATIONS Model BB5060 BB5072 BB5084 BB5096 BB5048L BB5060L Working Width, in. (cm) 61.5 (156.21) 73.5 (186.69) 85.5 (217.17) 97.5 (247.65) 50 (127.0) 62 (157.48) Endplate thickness (.95) (.95) (.95) (.95) (.80) (.80) Moldboard thickness (.48) (.48) (.48) (.48) (.48) (.48) Weight Operating, lb (kg) 418 (189.60) 474 (215.0) 510 (231.33) 602 (273.06) 360 (163.29) 392 (177.81) Shipping per stand, lb (kg) 913 (414.50) 1025 (465.35) 1097 (498.04) 1281 (581.57) 797 (361.84) 861 (390.89) Tractor Requirements PTO hp (kw) 60 max 60 max 60 max 60 max 18 max 18 max Hitch Type Cat. 1 Cat. 1 Cat. 1 Cat. 1 Cat. 1 Cat. 1 imatch TM Compatibility Yes Yes Yes Yes Yes Yes Box Capacity, cu ft (m 3 ) (.38) (.45) (.53) (.60) (.30) (.38) Cutting Edge Reversible Yes Yes Yes Yes Yes Yes Quantity Size, in. (cm) x 6 (.95 x 15.24) Duty x 6 (.95 x 15.24) x 6 (.95 x 15.24) x 6 (.95 x 15.24) x 6 (.95 x 15.24) x 6 (.95 x 15.24) Type Standard Standard Standard Standard Economy Economy Scarifier Shank type Points 4 hole 0.75 x 2.50 x 16 Standard crimp on style 4 hole 0.75 x 2.50 x 16 Standard crimp on style 4 hole 0.75 x 2.50 x 16 Standard crimp on style 4 hole 0.75 x 2.50 x 16 Standard crimp on style 4 hole 0.75 x 2.50 x 16 Standard cripm on style 4 hole 0.75 x 2.50 x 16 Standard crimp on style Quantity Tubular scarifier beam size, in. (cm) Beam reinforcement bar size, in. (cm) Tailgate x 4 (.64 x 10.16) square tube (1.27) square bar stock x 4 (.64 x 10.16) square tube (1.27) square bar stock x 4 (.64 x 10.16) square tube (1.27) square bar stock x 4 (.64 x 10.16) square tube (1.27) square bar stock x 4 (.64 x 10.16) square tube N/A x 4 (.64 x 10.16) square tube Type Fixed Fixed Fixed Fixed Fixed Fixed Mast Type Welded Welded Welded Welded Bolt on Bolt on Shipping Configuration Setup Time Fully assembled & palletized Fully assembled & palletized Fully assembled & palletized Fully assembled & palletized Fully assembled & palletized N/A Fully assembled & palletized Labor hours Warranty Time period 1-year (excluding wear parts) 1-year (excluding wear parts) 1-year (excluding wear parts) 1-year (excluding wear parts) 1-year (excluding wear parts) 1-year (excluding wear parts) 4 Specifications

5 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Safety is a primary concern in the design and manufacture of our products. Unfortunately, our efforts to provide safe equipment can be wiped out by an operator s single careless act. In addition to the design and configuration of equipment, hazard control and accident prevention are dependent upon the awareness, concern, judgment, and proper training of personnel involved in the operation, transport, maintenance and storage of equipment. It has been said The best safety device is an informed, careful operator. We ask you to be that kind of operator.!lea EL INSTRUCTIVO! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. TRAINING Safety instructions are important! Read all attachment and power unit manuals; follow all safety rules and safety decal information. (Replacement manuals and safety decals are available from your dealer.) Failure to follow instructions or safety rules can result in serious injury or death. If you do not understand any part of this manual and need assistance, see your dealer. Operators must be instructed in and be capable of the safe operation of the equipment, its attachments, and all controls. Do not allow anyone to operate this equipment without proper instructions. Never allow children or untrained persons to operate equipment. PREPARATION Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Make sure attachment is properly secured, adjusted, and in good operating condition. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate. TRANSPORTATION Always comply with all state and local lighting and marking requirements. Never allow riders on power unit or attachment. Do not operate or transport on steep slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Do not operate or transport equipment while under the influence of alcohol or drugs. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with a loader, front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate. (Safety Rules continued on next page) Safety 5

6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! (Safety Rules continued from previous page) OPERATION Always comply with all state and local lighting and marking requirements. Operate only in daylight or good artificial light. Keep bystanders away from equipment. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Never allow riders on power unit or attachment. Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine. Look down and to the rear and make sure area is clear before operating in reverse. Use extreme care when working close to fences, ditches, other obstructions, or on hillsides. Do not operate or transport on steep slopes. Do not stop, start, or change directions suddenly on slopes. Use extreme care and reduce ground speed on slopes and rough terrain. Watch for hidden hazards on the terrain during operation. Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. Before leaving operator s seat, lower lift arms and put attachment on the ground. Engage brake, stop engine, remove key, and remove seat belt. MAINTENANCE Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Make sure attachment is properly secured, adjusted, and in good operating condition. Before leaving operator s seat, lower lift arms and put attachment on the ground. Engage brake, stop engine, remove key, and remove seat belt. Never perform service or maintenance with engine running. Keep all persons away from operator control area while performing adjustments, service, or maintenance. Eye protection must be used when removing or installing scarifier shank clips. Tighten all bolts, nuts, and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service. STORAGE Block equipment securely for storage. Keep children and bystanders away from storage area. 6 Safety

7 DEALER PREPARATION CHECK LIST Frontier BB50 SERIES BOX BLADES THIS CHECKLIST IS TO REMAIN IN OWNER S MANUAL It is the responsibility of the dealer to complete the procedures listed below, then review this checklist with the customer upon the delivery or the sale of this implement. PRE-DELIVERY CHECK LIST (DEALER'S RESPONSIBILITY) Inspect the equipment thoroughly to be certain it is set up properly before delivering it to the customer. The following check list is a reminder of points to inspect. Check off each item if it is found satisfactory or after proper adjustment is made. Check that all safety decals are installed and in good condition. Replace if damaged. Check all bolts to be sure they are tight. Check that all cotter pins and safety pins are properly installed. DELIVERY CHECK LIST (DEALER S RESPONSIBILITY) Show customer the safe, proper procedures to be used when mounting, dismounting, and storing equipment. For mounted units, add wheel weights, ballast in front tires, and/or front tractor weight to enhance front end stability. A minimum 20% of tractor and equipment gross weight must be on front tractor wheels. When adding weight to attain 20% of tractor and equipment weight on front tractor wheels, you must not exceed the ROPS weight certification. Weigh the tractor and equipment. Do not estimate! Show customer how to make adjustments. Present Operator s Manual and request that customer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed. Point out the safety decals. Explain their meaning and the need to keep them in place and in good condition. Emphasize the increased safety hazards when instructions are not followed. Explain to customer the potential crushing hazards of going underneath raised equipment. Instruct customer that service work does not require going underneath unit and never to do so. Dealer Check List 7

8 SAFETY and INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 5 Replace Immediately if Damaged! 6 8 Back View Front View FALLING OFF 1 AVOID INJURY 2 CRUSHING & PINCHING 5 RED REFLECTOR 1.25 X 7.25 (2 Needed) RED REFLECTOR USE FOR MODEL BB5096 ONLY 5TITE AMBER REFLECTOR (1 Needed) AMBER REFLECTOR USE FOR MODEL BB5096 ONLY 4 SERIAL NUMBER 7 FRONTIER LOGO 5HDBB5000 5HDBB6000 Warning Label Sheet Part Number 5TITE (Contains Label #s 1, 2, 3, & 7) 5HDBB MODEL NUMBER 5HDBB Safety and Instruction Decals

9 SAFETY and INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! 6 Replace Immediately if Damaged! Back View FALLING OFF 4 SERIAL NUMBER 5 FRONTIER LOGO 1 AVOID INJURY 5BB4000 5BB CRUSHING & PINCHING 6 MODEL NUMBER Warning Label Sheet Part Number 5TITE (Contains Label #s 1, 2, 3, & 5) Safety and Instruction Decals 9

10 OPERATION The operator is responsible for the safe operation of this equipment. The operator must be properly trained. Operators should be familiar with the equipment, the tractor, and all safety practices before starting operation. Read the safety rules and safety decals on pages page 5 through page 9. The box blades are designed for a wide range of applications: scarifying, scraping, leveling, grading, and backfilling. WARNING CONNECTING BOX BLADE TO TRACTOR Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in locked up position at all times. Never allow children or untrained persons to operate equipment. Keep bystanders away from equipment. Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts. CAUTION Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation. Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. PRE-OPERATION CHECK LIST (OWNER S RESPONSIBILITY) Review and follow all safety rules and safety decal instructions on page 5 through page 9. Check that equipment is properly and securely attached to tractor. Check that all safety decals are installed and in good condition. Replace if damaged. Check that all hardware is properly installed and secured. Do not allow riders. Make sure tractor ROPS or ROPS CAB and seat belt are in good condition. Keep seat belt securely fastened during operation Category I Lift Pin 2. Lynch Pin Figure 1 - Connecting Box Blade to Tractor The box blade is compatible with Category 1, 3-point tractors equipped with side swing-type lower lift arms. 1. To avoid interference with the box blade, adjust tractor drawbar to the shortest and highest position. 2. Attach the tractor s lower lift arms to the box blade and secure in place with Category 1 lift pin (1) and lynch pin (2). 3. Attach the tractor s top link to the top of the box blade s mast and secure with the heavy-duty top link pin and retaining pin supplied with the top link. NOTICE The 3/4 bolt and sleeve in the lower hole provide the attachment point for a Category 1 quick coupler or imatch. Do not remove this bolt and sleeve when operating the blade. 10 Operation

11 ADJUSTING TOP LINK The box blade is leveled by adjusting the length of the tractor s top link. Shortening the top link will deepen the scarifier tooth penetration. Lengthening the top link will provide better scraping and leveling action. Experience will allow the operator to determine the best setting for the application being done. SCARIFYING 1. Place the scarifier shanks in position with the points facing toward the tractor. 2. Lock into position with the lock keys provided. The lower shank position provides the greatest ground penetration. 3. Lower the box blade and drive the tractor ahead to begin the scarifying operation. 4. Adjust the depth of the scarifier by tilting the unit with the tractor top link. Shortening the top link will provide deeper and more aggressive operation. SCRAPING 1. Raise or remove the scarifier shanks. Lower the box blade and drive forward to move material. 2. Adjust the depth of the blade by tilting the unit with the tractor top link. Shortening the top link when scraping will transfer more weight on the front of the blade and will raise the cutting blade to provide a more shallow cut. NOTE: When the top link is adjusted properly, the bowl of the blade should fill easily and material can be pulled to a desired location. 3. To change the level of the blade, shorten or lengthen the tractor lift arm tilt link to provide the correct slope. 4. Spread material by gradually raising the box blade as the tractor moves forward. NOTE: Top link adjustment for loose or previously scarified material will differ from adjustment for hard or compacted material. OPERATION BACKFILLING 1. Raise or remove scarifier shanks. 2. Lower the blade to the ground and back up into the fill material. 3. Shorten the top link to raise the cutting blade and control how much the blade digs in. LEVELING 1. Raise or remove scarifier shanks. 2. Shorten the top link so the cutting edge clears the ground. 3. Drive forward with the box blade in this position and loose material will be leveled. CLEANING After Each Use Remove large debris such as clumps of dirt, grass, crop residue, etc. from machine. Inspect machine and replace worn or damaged parts. Replace any safety decals that are missing or not readable. Periodically or Before Extended Storage Clean large debris such as clumps of dirt, grass, crop residue, etc. from machine. Remove the remainder using a low-pressure water spray. 1. Be careful when spraying near scratched or torn safety decals or near edges of decals as water spray can peel decal off surface. 2. Be careful when spraying near chipped or scratched paint as water spray can lift paint. 3. If a pressure washer is used, follow the advice of the pressure washer manufacturer. Inspect machine and replace worn or damaged parts. Sand down scratches and the edges of areas of missing paint and coat with spray paint of matching color (purchase from your dealer). Replace any safety decals that are missing or not readable (supplied free by your dealer). See Safety Decals section for location drawing. Operation 11

12 STORAGE OPERATION WARNING Block equipment securely for storage (see Figure 2). Keep children and bystanders away from storage area. WARNING OWNER SERVICE The information in this section is written for operators who possess basic mechanical skills. If you need help, your dealer has trained service technicians available. For your protection, read and follow the safety information in this manual. NEVER GO UNDERNEATH EQUIPMENT. Never place any part of the body underneath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak-down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpectedly and cause severe injury or death. Service work does not require going underneath. Read Operator s Manual for service instructions or have service performed by a qualified dealer. Keep all persons away from operator control area while performing adjustments, service, or maintenance. Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pressure, set parking brake, stop engine, remove key, and unfasten seat belt. BLOCKING UP BOX BLADE NOTE: To service the box blade when attached to the tractor, it must be blocked up off the ground. 1. Place two 4 x 4 blocks under each side frame of the box blade as shown in Figure Lower the box blade to rest securely on the blocks. 3. Do not block the machine any higher than needed for removing the shanks or cutting edge. CAUTION Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate. Figure 2 - Box Blade Blocked Up 12 Operation / Owner Service

13 REMOVING SCARIFIER SHANKS Scarifier shanks have four operating positions in the blade. They may be removed if scarifying action is not needed. 1. Block up machine by placing two 4 x 4 (10 x 10 cm) blocks under each side-frame of the box blade (see Figure 2). 2. Lower the box blade to rest securely on the blocks. NOTE: Do not block the machine any higher than necessary to remove the shanks or cutting edge. 3. Remove clip pin (1) and and remove L pin (2). 4. Remove or adjust hole placement in shank (3) and replace L pin (2) and clip pin (1). 2 OWNER SERVICE REPLACING CUTTING EDGE All box blade models use two 3/8 x 6 (9.53 x 152 mm) cutting edges. They are interchangeable and reversible. To service the box blade when attached to the tractor, it must be blocked up off the ground. 1. Place two 4 x 4 (10 x 10 cm) blocks under each side-frame of the box blade (see Figure 2). 2. Lower the box blade to rest securely on the blocks. NOTE: Do not block the machine any higher than necessary to remove the shanks or cutting edge. 3. Refer to parts drawings, pages 14 through 15. Remove the bolt set (6-5TITE511163; 5-5TITE511163) from blade. Turn cutting edge over and use new edge, or replace it if both edges have been used. 4. Attach cutting edge to box blade and secure with plow bolts and hex nuts previously removed. Torque plow bolts to specifications given in Bolt Torque Chart, page Figure 3 - Scarifier Shanks Owner Service 13

14 PARTS c 5 A-FRAME HITCH & BB5060, BB5072, BB5084, BB5096 PARTS LIST Item Number Part Number Description 1 5TITE Box Blade Top Link Bushing w/hardware 2 5TITE /8 x 6 Category 1 Roll Pin w/lynch Pin 3 5TITE /2 x 4 L Pin w/clip Pin (2 pk) 4 5TITE Cutting Edge 4a 5TITE Cutting Edge 4b 5TITE Cutting Edge 4c 5TITE Cutting Edge 5 5TITE Hole Shank 6 5TITE Bolt Set for the Cutting Edge (6 pk) 7 5TITE Manual Tube Holder w/hardware 14 Parts

15 PARTS a 3 A-FRAME HITCH & BB5048L, BB5060L PARTS LIST Item Number Part Number Description 1 TIFC Category 1 Lift Pin 2 5TITE Cutting Edge 2a 5TITE Cutting Edge 3 5TITE Hole Shank 4 5TITE /2 x 4 L Pin w/clip Pin (2 pk) 5 5TITE Bolt Set for Cutting Edge Mounting (6 pk) 6 5TITE Vertical Brace Lift Arm (2 pk) 7 5TITE Angle Brace Back Strap (2 pk) 8 5TITE Lift Arm Spacer w/hardware 9 5TITE Angle Brace Back Strap Hardware Pack (2 pk) 10 5TITE Manual Tube Holder w/hardware Parts 15

16 BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. All torque values are given to specifications used on hardware defined by SAE J1701 & J1701M JUL96. A SAE Series Torque Chart SAE Grade 2 No Dashes SAE Bolt Head Identification SAE Grade 5 (3 Radial Dashes) SAE Grade 8 (6 Radial Dashes) A Diameter (inches) Wrench Size MARKING ON HEAD SAE 2 SAE 5 SAE 8 lbs-ft N-m lbs-ft N-m lbs-ft N-m 1/4 7/ /16 1/ /8 9/ /16 5/ /2 3/ /16 13/ /8 15/ /4 1-1/ /8 1-5/ / A METRIC Series Torque Chart Metric Bolt Head 8.8 Identification 10.9 Metric Grade 8.8 Metric Grade 10.9 A Diameter & Thread Pitch (Millimeters) Wrench Size COARSE THREAD MARKING ON HEAD 16 Bolt Torque Chart FINE THREAD MARKING ON HEAD Metric 8.8 Metric 10.9 Metric 8.8 Metric 10.9 N-m lbs-ft N-m lbs-ft N-m lbs-ft N-m lbs-ft Diameter & Thread Pitch (Millimeters) 6 x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x x mm x 2.0 A

17 SAE Bolt Thread Sizes BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. METRIC BOLT THREAD SIZES 8MM 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG...Agriculture MPa...Mega Pascal ASABE... American Society of Agricultural & N...Newton Biological Engineers (formerly ASAE) NC...National Coarse ASAE...American Society of Agricultural Engineers NF...National Fine ATF... Automatic Transmission Fluid NPSM...National Pipe Straight Mechanical BSPP...British Standard Pipe Parallel NPT... National Pipe Tapered BSPTM...British Standard Pipe Tapered Male NPT SWF... National Pipe Tapered Swivel Female CV...Constant Velocity ORBM... O-Ring Boss - Male CCW... Counter-Clockwise P...Pitch CW... Clockwise PBY... Power-Beyond F... Female psi...pounds per Square Inch FT... Full Thread PTO... Power Take Off GA... Gauge QD...Quick Disconnect GR (5, etc.)...grade (5, etc.) RH...Right Hand HHCS...Hex Head Cap Screw ROPS... Roll-Over Protective Structure HT... Heat-Treated RPM... Revolutions Per Minute JIC...Joint Industry Council 37 Degree Flare RT... Right LH...Left Hand SAE...Society of Automotive Engineers LT... Left UNC...Unified Coarse m...meter UNF...Unified Fine mm...millimeter UNS...Unified Special M... Male Bolt Size Chart 17

18 18 Notes NOTES

19 NOTES Notes 19

20 PART NUMBER 5TITE511191