RIKO PTO Skidding Winches with manual control. These have a pair of hand operated controls actuated by two long cords with T handles on the end.

Transcription

1

2 RIKO PTO Skidding Winches with manual control. These have a pair of hand operated controls actuated by two long cords with T handles on the end. This allows the operator to stand away from the winch or operate the winch from the tractor cab. One control is for the band brake and one operates the winch in. The range runs from 3 ton to 8.5 ton pull.

3 RIKO PTO Skidding Winches with hydraulic control. Instead of having cord operated hand controls, there is a hand held electro-hydraulic control unit. This has a long lead so the operator can stand away from the winch or operate the winch from the tractor cab. To further enhance ease of use, there is an optional radio remote control with multiple channels. There is a 6 channel unit or an 8 channel unit, which includes engine speed control for the tractor. Direct gear driven hydraulic pump. Slide up legs with spring locking pin. Optional: Hydraulic wire unwinding. Radio remote control. Standard: PTO shaft. Chain box. Axe holder. Top & Lower Pulley. Wander Lead. Tow hitch. Saw holder: 40H,50H,60H,80H.

4 Single Drum 6.5, 70, 8.5 & 9 ton. Double Drum 6.5 & 8.5 Ton. Double Drum 10 Ton Skid unit. Mounted in a Skidding Butt plate or mounted directly onto the front or rear of any tractor. Specialised guarding and Butt plates can be made to order. The drum winches use a hydraulic worm gear and multi clutch plates to ensure maximum winching power. On the double drum models, the two drums are independent, so you can winch out with one and in with the other.

5 Riko offers a wide range of log splitters for both domestic and professional users. The 7 ton models are available with 240vlt electric motor or petrol engine. The 9 ton comes as standard for use with the tractor hydraulics but can be supplied with a 240vlt electric motor or petrol engine kit with wheels. The kit sits under the splitter so raises the table height. The 10 ton has a 240vlt electric motor or petrol engine and is available with a fixed height table or adjustable height table. The 12 ton model comes as standard for use with the tractor hydraulics but can be supplied with a PTO kit, 240vlt electric motor, petrol engine or even a combination of power sources. As long as the wiring at the premises is of a suitable standard all 240vlt electric splitters can be plugged into a standard 13amp 3 pin plug. 12 Ton Domestic and Semi-professional Range 9 Ton 10 Ton 10 Ton 7 Ton RIKO TITANIUM VERTICAL SPLITTERS. Power options: Tractor hydraulics. Tractor PTO. 3 Phase Electric. Combination PTO & Electric. The larger Titanium range have splitting forces from 13 to 26 ton will take timber up to 115cm in length so there is a splitter for all types and sizes of timber. They have a variable height and removable table so you can split rings or billet long timber. There is also a timber lifter which means you can role larger timber onto the lifter, and the hydraulic splitting ram then provides the power to stand the large timber up ready for splitting under the knife. On all Titanium splitters the splitting knife can be stopped at any point without the ram retracting, then a simple push on the control handles and the ram retracts. There is also an adjustable stop so you can set the return stroke to stop at a given height. This greatly increases overall output when splitting short rings as you don t have to wait for the ram to travel its full stroke. Options include: 4 way knives. Axles for moving the larger splitters around a yard or estate. Hydraulic winch to drag timber across to the splitter.

6 RIKO Horizontal splitters are ideal for splitting long timber into billets. There are many ways of powering the splitters: tractor PTO, tractor hydraulics, 240vlt & 415vlt electric motors, petrol engine and even diesel engines or a combination of power sources. The horizontal models run from 14 tons up to 50 tons splitting force. Standard timber lengths are 110cm however, on request & depending on the model; this can be increased up to a maximum of 3 meters. 23 Ton 14 Ton 23 Ton 2.6 Metre Options: Drop on 4 & 6 way knives. Hydraulically adjustable 2-4 way knives. Hydraulic side loading. Hydraulic winch loading with or without remote control. Crane loading with or without remote control. RIKO PRO 33-43: ton. With side load, Hydraulic knife and folding table. RIKO Special build ton Horizontal Log Splitters. On the left is a 40 Ton PTO driven splitter with 2.6 meter split. Yard tow axle and Radio remote control Hydraulic 2-4 way knife.

7 For more than 30 years Split-Fire Sales has been the leading manufacturer of wood splitters in Canada. They are manufactured in Norwich, Ontario, Canada using state of the art manufacturing and components. All Split-Fire wood splitters feature the hallmark 2-way splitting action on both the forward and reverse stroke, doubling productivity. This is a vastly different concept compared to single stroke machines using a flat push plate and wedge. This design allows operators to split wood both ways, increasing output by up to 35%. Split-Fire log splitters are available with 16, 20 and 32 ton splitting force. Standard models are tractor linkage mounted and use the tractor hydraulics. There are optional PTO, Electric motor and Petrol engine models. There is also an optional timber lifter, four way knife and axle kits for yard to or highway towing with IVA approval. 1) With Split-Fire the log is always stationary whilst being split. The log is held centrally on the splitting beam whilst the knife splits the log. 2) The split log can then be rotated 90 degrees so one split half is lying on top of the other split half. The knife then splits the log the second time on the return stroke. 3) The unique end stop actually grips the log and allows the log to open up as the knife splits the log. This design helps prevent wat we call kick outs which is when the log flies off the splitter 4) There are Split-Fire models that have a single two sided knife. However there are also models that have an interchangeable single and four-way two sided knifes. WHY BUY SPLIT-FIRE: Splits on outstroke and return stroke increasing output by up to 35% and keeps the log in the same place. Unique Anti Kick-Out log grip design helps stop logs flying off as they split. Central Log holding bars help locate & hold the timber in the centre of the splitter ready for splitting. Two large side wings create a large work area & ensure the logs stay in the splitting zone before, during and after splitting. Optional Timber lifter for lifting large timber up to the splitting / work zone. Standard Tractor hydraulic model can be upgraded to PTO, Electric motor, petrol engine and towable with or without IVA.

8 Riko vertical trailed splitters have been designed specifically for the user that needs a mobile splitter for working in various locations. The most popular model is the petrol engine UF14BMF with removable table. Its low overall height & under 750Kg weight means the splitter is ideal for tree surgeons and hire shops. Options include a slide over 4 way knife. RikoTitanium BMF Riko horizontal trailed splitters are designed for high volume production of logs and billets. Available from 14, 18 and up to 23 ton splitting forces. They all come as standard with a solid yard tow axle and splitting length of 1.1 metre, however the 18 ton can be ordered with a splitting length of up to 2 meter and the 23 ton up to 2.5 meter. There are various options such as a drop on 4 way knife or hydraulic 4 way knife, timber loader and all models are available with an upgrade to road tow with fully approved IVA. On the Right is our 15 ton Speedy 550C log splitter with PTO drive. It has been designed to be towed behind small compact tractors that do not have the linkage lift capacity or oil flow to operate a log sized log splitter. The splitting length is 550cm and it comes as standard with a height adjustable four way knife. Hydraulic adjustable knife is an option. If you don t have a tractor the Speedy 550 can be supplied with a petrol engine. It is also available with an upgrade to road tow with fully approved IVA. On the left is a 14 ton 1.1 meter stroke with 8.5hp petrol engine, along with single hydraulic pump and yard tow axle. To make the machine stable when working there is a removable leg at the knife end, and a wind down leg at the engine end. The draw bar has been removed for the picture. On all Riko Horizontal splitters the splitting knife can be stopped at any point without the ram retracting, then a simple push on the control handles and the ram retracts. There is an optional adjustable stop so you can set the return stroke to stop at a given point. This greatly increases overall output when splitting short lengths as you don t have to wait for the ram to travel its full stroke.

9 Small cone splitters are not a new thing, however large hydraulic drive cone splitters are. They can be fitted on any type of crane, handler or excavator for billeting long timber or breaking down large diameter timber into billets for processing or further splitting. Fitted to the leg of a forwarder, long timber can be split down as the trailer is loaded to maximise the volume loaded onto the trailer. They are also ideal for braking down ugly timber or roots into smaller parts to feed into a grinder or chipper. Extracting big roots often requires a big machine, but using a cone splitter on a small excavator, the roots can be broken up whilst in the ground, enabling the small machine to then hook them out. M1 Roli for Ton excavators etc.

10 Riko logging saws come in three models the LIGHT, PRO and the PRO-PLUS. The circular saw blades are 700mm diameter and Tungsten tipped for long life. For easy moving wheels and handle/s are standard on all models. For extra safety all models are fitted with a log grip. The Pro models have a trough extension and a fixed log length cut indicator. The Pro-Plus model has an adjustable log length cut indicator. Safety cut system so you cannot cut without one hand being on the trough handle, combined with the log grip this gives total two handed use. The LIGHT is 240vlt whilst the PRO and PRO-PLUS models are available as PTO, 240vlt or 3 phase electric or with a petrol engine. The PRO-PLUS Petrol engine model is also available as a road tow with full IVA approval. LIGHT PRO PRO-PLUS PRO-PLUS PETROL ROAD TOW PRO-PLUS PETROL BAND SAWS. Riko band saws come in four different sizes. They can be powered from the tractor PTO or from single or 3 phase electric. There is also the option for PTO and electric power. There is a choice of blades and guide rollers for precision cutting. The optional log trough makes the band saw truly versatile. LOG GRIP. The optional log rough converts your band saw into a log saw.

11 RIKO combination saw and elevator model has a variable height telescopic conveyor that is driven hydraulically from the tractors own spool valve, or from the built-in optional PTO hydraulic pack. A 3 phase and petrol engine version is also available. The petrol engine version can have a yard tow axle kit added. In all cases, a pair of extending, height adjustable legs support the conveyor when it is extended. The whole machine folds up for easy transport & storage. Shown at maximum working height The petrol powered saw and conveyor can also have a solid axle and tow bar fitted for yard towing or road towing behind a tractor. A high speed road tow version is available with full IVA approval. The Riko ranges of conveyors are available to suit logs or chip and pellets. The standard models are for logs and can be used alongside log splitters, logging saws, band saws etc. The professional models have a choice of belt widths of 250mm or 400mm and are available in 4 and 5 meter lengths. Longer length non telescopic models can be ordered. They are all variable height and come with wheels and a drawbar. They can be powered by electric, hydraulic or petrol engines. The Pro models come in a crate for partial home assembly.

12 Designed and built for working on the mountains of Europe, Alpine tractors are perfectly suited to work in all aspects of forestry, woodlands and ground care. Their low centre of gravity provides vastly improved stability over a conventional tractor. Unlike conventional tractors with a rigid chassis and a pivoting front axle, the Alpine tractor chassis oscillates just behind the front axle. This ensures both front and rear axles follow the contours of the ground, maintaining traction and stability in the most arduous of conditions. With the engine positioned in front of the front axle, the wheelbase is shorter than a conventional tractor, improving the turning radius. It acts as a counter balance to the rear linkage, thus providing excellent lifting capacity and towing ability for their size and weight. And with engine sizes from 22hp up to 97hp, Alpine tractors are packed with power.

13 RIKO COMBY Processors are a basic machine consisting of a tungsten tipped saw blade and 15 ton horizontal log splitter. They can also be ordered with a telescopic conveyor. There are 2 models to choose from, the COMBY PRO-2010 TSC and the COMBY PRO-PLUS TSC 4/5. The Comby range is designed to provide a low cost, but very efficient processor with a very respectable 15 tons splitting force. They are ideally suited to processing hedgerow timber that is often in short lengths, twisted and knotty, hence the 15 ton splitter. On all models the saw blade is driven by the PTO shaft, which also drives a hydraulic pump and tank to power the splitter. On the Pro the conveyor uses a single acting flow and return from the tractor but there is an upgrade kit so everything runs of the PTO drive. This kit is standard on the Pro-Plus so even if it s an old tractor with a PTO but no hydraulics it can still run the Pro or Pro-Plus. The Comby Processor Range is available with a solid axle and draw bar for towing around the estate or yard with a tractor or other suitable vehicle. They are not available as a high speed road tow version.

14 Riko believe that the Farmi WP30-36 Firewood Processors are the fastest and best value processor, of its size, on the market. Where else can you buy a 14 diameter cut road tow firewood processor? Fully manual controls with no electronics. 36cm diameter cut but has a larger throat so handles twisted and distorted timber. Unique walking floor feeds the timber and holds the timber during cutting. It feeds cuts and splits in two movements rather than three movements, so a quicker cycle time. Slewing output elevators as standard. Standard PTO machine can have a petrol engine, electric motor, and road tow axle added at any time. Duun Firewood Processors are one of Norway s bestselling ranges. All have chainsaw cut and conveyor infeed and outfeed. Standard models are PTO powered, 3 phase models are available. There are 3 models to choose from: DUVM320, 32cm cut & 5.6 ton split. DUVM370X, 37cm cut & 8.5 ton split. Joystick control of feed, cut and split. Hydraulic knife adjustment and manual slewing conveyor. DUVM420X, 42cm cut and 11 ton split. Hydraulic log grip. Joystick control of feed, cut and split. Hydraulic knife adjustment. Manual slewing conveyor. There is a manual timber rack for all models and a timber rack with hydraulic roller feed for the 370X and 420X. The 420X can also be fitted with a sawdust conveyor. DUVM370X - 420X DUVM370X - 420X DUVM370X - 420X DUVM320

15 The Riko Titan Firewood Processor is PTO powered as standard and an be ordered with 3 phase and PTO. There are no electronic controls on the Titan 40-20, all the controls are directly operated joystick and single lever hydraulic spool valves. The Titan cuts up to 40cm diameter timber using a belt driven, hydraulic operated, Tungsten tipped circular saw blade. Once cut the log drops onto a holding plate that then tips the log into the splitting. This almost eliminates the problem of logs dropping into the splitting chamber the wrong way. Once in the splitting trough the log is pushed with a force of 20 tons through the hydraulic height adjustable window knife. There is a choice of 2/4, 2/6, 2/8 or 2/12 way window knives. Manual hydraulic controls, ne electronics. Cuts timber up to 40cm diameter with Tungsten tipped saw blade. 20 ton splitting force. Window splitting blade with choice of 2/4, 2/6, 2/8 or 2/12 way knives. Hydraulic roller in-feed and slewing output elevator. Optional hydraulic timber lifter and timber rack.

16 The Renewable Heat Incentive (RHI) requires Firewood to be dried to below specific moisture contents. For Kiln dried Firewood it is<20% moisture content and for naturally dried it is <25% moisture content. The better the air circulation the quicker the Firewood will season. Billets win hands down over logs, even if the logs are loose, bagged or boxed. Billets are far easier to handle, stack and store. They season quicker and give you the benefit of being able to cut any length log from the seasoned Billet so you are not limited to pre-set log lengths associated with a traditional Processor. The design of the Riko Billet Processors ensures simplicity of use whilst maintaining operator safety. It is as simple as it is ingenious: there are tubular compartments built into a rotating drum, the billet lengths are simply dropped into each chamber as it rotates. As the drum rotates each billet is cut drops down a preset amount so that each cut produces a log the same length. The Tungsten tipped circular saw blade then cuts the Billet and the cut log is discharged into the area above the conveyor belt. As the drum continues to rotate the next Billet is cut and each Billet drops down further ready to be cut on the next rotation. This process continues as the drum rotates and it is simply a case of placing another Billet in the tubular compartments as the drum continues to rotate. The Riko Billet Processors ensures:- The fastest natural method of achieving seasoned wood fuel. Tungsten tipped saw & Log grip Forward / stop / reverse drum control Wide and deep Billet compartments There are three main models of Rotary Billet Rotomat: The Pro-Plus Drum saw with four Billet tubes, the Rotomat 4 with four Billet tubes and Rotomat 5 with 5 Billet tubes. All can be powered by a tractor PTO or by a 3 phase electric motor and can be ordered with or without the telescopic conveyor. The Rotomat 4 can also be ordered as a road tow with petrol engine. The R5 takes Billets up to 120cm long & cuts logs to 20/25/33/50cm. With a maximum of 72 cuts per minute the R5 can process up to 15 cm/h of Billets. The R4 takes Billets up to 100cm long & cuts logs to 20/25/28/33cm. With a maximum of 68 cuts per minute the R4 can process up to 10 cm/h of Billets. The Pro-Plus drum saw cuts logs to a length of 25cm to 50cm. Depending on type of wood etc. the manufacturer claim an out put of up to 11 tons per hour.

17 One of the fastest ways to dry timber is to cut it into one meter lengths and then split into billets. The Billet Bundler is designed to enable you to create 1 cubic meter bundles that can easily be handled and stacked in much the same way as large round bales. Individual 1 meter cut lengths of timber are placed onto the carrier frame. Once full, the bundle is held secure by nylon straps that are tensioned and then secured using a hand held tensioning ratchet and tool. Once secure, the bundle can be manually tipped onto the ground. The standard Billet Bundler mounts on the tractors 3 point linkage and is manually tipped once loaded. There is a hydraulic tipping option and a front loader mounting option. South East (Head Office). Inverallen Yard, Forge Road, Kingsley, Hampshire, GU35 9LW Telephone: enquiries@riko-uk.com North East. Unit 10, Spruce & Hawe yard, Blind Lane, Near Tockwith, YO26 7QJ Tel: enquiries@riko-uk.com South Wales. Mountain View, Cold Blow, Narberth, Pembrokeshire, SA67 8RR Tel: enquiries@riko-uk.com : North Wales. Nant Mostyn, Cyffylliog, Ruthin, Denbighshire, LL25 2DP Tel: enquiries@riko-uk.com

18 Riko Forest-master forestry mulching flails are a heavy forestry mower with cage rotor with hammer blades that can swing back into the rotor when the hit obstacles that cannot be mulched. Due to there low weight of Kg they are ideally suited for use with Alpine Tractors. They are used for mowing or pulverising bushes and young trees. Ideally suited for working between young plantation, preparing and maintaining towing paths or forest rides, fire-corridors, mowing and pulverising before replanting or for cultivating fallow areas. The Forest-master can be ordered for use used / mounted in both directions, forwards or backwards. It comes in 3 widths. 110cm, 150cm or 180cm cutting widths. Cuts material up to 10cm diameter with swinging hammers.. Manual side shift with optional hydraulic side shift. Optional tree pushers, rear closing hood Optional hydraulic timber lifter and timber rack.

19 The Scorpion 1300F and 1800F both fit front end loaders and have a hydraulic rotator. They are fitted with a 12vlt diverter valve so require only one DA hydraulic service. The Scorpion 1300F fits on the three point linkage on tractors 30-70hp. The larger Scorpion 1800F is for 70HP+ tractors and also fits front loaders etc. When they are fitted on the rear linkage both can be supplied with a radio remote controlled winch for pulling inaccessible timber to the grab. The largest 3 point linkage skidders are the Scorpion PRO models. The have extending booms that can slew sideways for increased ease of access and flexibility when loading. There are mechanical and hydraulic slewing / extending options and the PRO3 comes with its own spool valve There are five models of Riko timber grabs and they are suitable for large front loaders or telescopic handlers. With the relevant brackets, they can fit all makes of loaders and handlers: 1) Forest blade with hydraulic top beak. 2) Pallet forks with adjustable tines and single removable hydraulic top beak. 3) Timber grab with twin beak. 4) Clearing grab with multi tines. 5) Scorpion 1300F Timber grab and rotator

20 Riko timber grabs can be fitted to cranes, backhoes, excavators etc. There are two types: the Standard and the Combi, which is ideal for clearing loose scrub / brash material etc. There are various models and sizes available, the smallest has a maximum opening of 70 cm from tip to tip and comes complete with continuous rotator. There are then 3 ranges, one for forestry cranes, one for 3 to 12 ton excavators and one for 12 to 25 ton excavators. Maximum tip to tip opening is from 1 meter up to 2 meters. The Riko range of Rotators is suitable for all makes of timber grabs, processors / felling heads and harvester heads. Loadings are from 1000 Kg up to Kg STANDARD COMBI & BM (Combi has extra bolt on tines) Model Weight A B C D E F G JLGRAB & Rotator tba tba tba tba tba 250 TECTHL30 Grab TETCTHLS30 Grab UFGR1100 PRO TETCHLS30 Combi TECTP120 Grab TECTP120 Combi UFGR1300 PRO UFGR1500 PRO UFGR1500 BM TECTP155 Grab UFGR AHTG28ST AHTG42ST COBUCKET50L NA NA 605 NA 396 COBUCKET60L NA NA 605 NA 496 CO-ROTATOR tba 1 ton rotator plus UFGR30PF tba 3 ton rotator plus 4 bolt flange adaptor UGFR465 tba 4.5 ton rotator with 4 bolt fixing UFGR603DSB tba 6 ton rotator with 6 bolt fixing

21 Felling Heads are suitable for tractor mounted cranes, forwarders, dedicated harvesters and excavators. The smallest Felling head is the UFRK250 which weighs 220Kg and the grab opens to 100cm tip to tip. It will cut 25cm in softwood and 20cm in hardwood. The UFRK250 can be fitted to a rotator or directly to the hitch of a 360 excavator. The largest Felling Head APPTC300 which weighs 770Kg and is for fitting to large 360 excavators directly or with a work and gear rotator. It can be fitted with a 300mm blade which will cut 30cm, or a 400mm blade which will cut 38cm. The grab opens to 139cm tip to tip. APPTC300 UFRK250 Riko Harvesting Heads. There are models suitable for tractor mounted cranes, forwarders, dedicated harvesters and excavators. They fell the tree and then using a stoke action de-limb and cut the timber to length. The range starts with the S23 which weighs 230 Kg, the largest weighs 380Kg and has additional Grip rollers that double the speed of the stroke and therefore doubles the output speed. S23C now available with Bluetooth device which measures the length of the log and automatically cuts the tree. RIKO S23 Felling & S23 Logging head. Fells like the RS25 and has an optional adaptation for the blade that splits the log in half when it is cut to length. The S23 weighs 230Kg and is suitable for forestry cranes and 5-8 ton 360 excavators. If the forestry crane is roof mounted or mounted on a Jake plate there is an option bag carrier for the tractor linkage or you can log into a suitable bulk trailer or vehicle. A key feature of the S23 is that it only uses the grab outlets on the rotator and no electrics.

22 The Riko Kinetic 8 X 8 is a low impact forwarder. The Kinetic has been designed as a serious, high output, professional machine for low impact work by forestry owners and contractors. The standard build includes crane, grab, rotator and the hydraulic extending chassis to reduce the length for transport to 5187mm from the working length of 5787mm. The weight is around 2100Kg with a carrying capacity of 3000Kg. The load area is hydraulically extending, which allows you to optimise the bunk area to suit for the timber length being loaded. It is powered by a 26hp 3 cylinder Diesel engine, with smooth and quite low fuel cost and longevity. The transmission is a mechanical gearbox with four forward and one reverse driving, a Vario transmission for clutch-less drive from stationary to full speed in each gear. The operator has full control of steering and forward / reverse drive whilst seated in the crane operating position. 8 equal size wheels mean you can fit four band tracks for a super low footprint. Some similar machines have single front wheels and four rear wheels meaning you can only fit band tracks on the rear wheels.

23 Riko trailers are designed to be low impact, easily transportable and have a capacity from 1000Kg to 5000Kg, with a choice of cranes from 3.2 to 4.8 meters. There are two designs, one with a single central beam and the stronger Ladder chassis models that have the advantage of being able to fold in half so the trailer and tractor can be transported on a road trailer etc. The cranes can be mounted on the trailer or on the tractor 3 point linkage. They are the perfect match for ATV s, compact tractors and of course, our Alpine tractors. The petrol power pack sits on the front rack of the ATV or can be built into the trailer. Options include: radio remote winch, clam shell grab, post hole auger and there are even demountable tipping bodies. 3 ton ladder chassis trailer, 3.2 crane, 50HP Alpine 3.2 crane linkage mounted on 50HP Alpine Single beam trailers, 1.5 ton & 3.3m crane, 3 ton & 4.7m crane, 5 ton & 4.8m crane No tractor? No Problem! The 1.5 ton trailer is available with 5 wheel drive and its own power pack + all the normal options. Hydraulic assist drive Hydraulic drive with band track Boom mounted winch. (Optional remote control) Easy & affordable extraction with the Riko Logging Arch. The optional rear Bogey keeps the whole tree clean.

24 The Riko range of larger trailers are designed to be exceedingly strong and user friendly. With trailer load capacities from 5000Kg to 14000Kg, and a choice of cranes from 3.8 meters to 8.6 meters, they are built for serious professional use. Standard Trailer models are: COT5: 5 ton single beam chassis. ON7: 7 ton single beam chassis. ON10: 10 ton with ladder chassis. ON12: 12 ton with ladder chassis ON14: 14 ton with ladder chassis Standard Crane models are: CO meter maximum reach. ON meter maximum reach. ON67S 6.7 meter maximum reach. ON meter maximum reach. ON meter maximum reach. ON meter maximum reach. Standard equipment T models: Brakes on two axles (not COT5 or ON7). Lights. Pivoting bolsters. Adjustable bunks. Steering drawbar (not COT5 or ON7). Optional equipment: Floatation tyres Steering drawbar for ON7 Brakes on 4 wheels. Hyd 2WD on the ON14. PTO pump and tank. Chassis extensions. Bolster extensions. Various tyre options. Control valve options. Interchangeable bodies