Powered Hoists. Catalog 1150 July Hoists - Powered Phone: Web: hubbellpowersystems.

Transcription

1 Powered Hoists Catalog 1150 Page 1151

2 1,000-lb. & 3,000-lb. Load Ratings 12V, 115V, 230V, Hydraulic, Gasoline Powerful design for tough jobs. Improved design features a multiple-planetary drive/backstop clutch assembled on the center shaft of a steel gearcase with full-length internal teeth. This design handles more rugged jobs, extends service life and reduces maintenance. Hoi s t s - Powered For improved load control, steel capstan drum features nickel-plated rope surface, larger radius at load-line wrap Optional Rope Lock At left: Automatically supports and rope hook. Position fall line so it will not pullover end load when fall line is released, until operator resumes of drum. If rope comes off end of drum and hook catches hoisting. At right: The release lanyard permits lowering or it, stop hoist, secure load and correct rope position on lifting load with precise control over speed and distance. drum. 1,000-lb. Hoists and Accessories... Pages TABLE OF CONTENTS 3,000-lb. Hoists and Accessories... Pages Versatile to various applications Lightweight, powerful portable hoists move heavyweight and difficult-access tasks, including: Setting utility poles Cell tower erection Pulling wheeled equipment over obstacles Raising transformers (even over fences in back lots) Hoisting heavy insulators Stringing and tensioning conductors Pulling indoor and underground cable Highly-accurate controls allow loads to be moved a fraction of an inch Note: Always use at least as many wraps of rope on the drum to lower a load as required to lift that load Mechanical Advantage of Series 90 Hoists Simple technique eases all loads Graph and diagram at right show capstan principle in action Operator effort remains low for typical loads simply by adding wraps on capstan drum Little effort is required, any crew member can run hoist Example: 4 wraps of rope = 1:44 ratio. That is, 1 lb. pull on Fall Line develops 44 lb. lift on Load Line. Therefore, 20 lb. of pull develops 880 lb. of lift. Page 1152

3 Electric Drive 1,000-lb. Load Rating 12-Volt DC Power Hoist with 25' #2 Cu Cable, four Terminals, Relay, Foot Switch C /2 lb. (25.7 kg.) 115-Volt AC includes Power Hoist and Foot Control Switch only C Volt AC includes Power Hoist and Foot Control C Electrical source requirements A m pe r e s VDC Unit Load pounds 49 lb. (22.2 kg.) 49 1 /2 lb. (22.5 kg.) Hydraulic Drive includes Power Hoist only; To order Foot Control Switch, see page C /2 lb. (12.9 kg.) Gasoline Drive includes Power Hoist and Foot Throttle Control only; Recommended bracket: C , see next page. C V Unit 46 lb. (20.9 kg.) 230V Unit Load pounds 9.5" H 17"L 7" W Four 3 8" mounting bolts furnished with each unit. Mounting flange provides eight 3 8" tapped holes on 5 5 8" bolt circle. Hydraulic-drive hoist does not include foot control switch. Gasoline unit features 35 cubic-centimeter 4-cycle engine. Series 90 Hoist Rope Speed for 1,000 lb. load Source Required to meet Rope Speed Rate 12-Volt DC 22 feet per minute 90 amperes motor current 115-Volt AC 40 feet per minute 14 amperes motor current 230-Volt AC 21 feet per minute 7 amperes motor current Hydraulic 93 feet per minute 8 gal. per min. & 1,000psi Gasoline 40 feet per minute Engine speed: 7,000rpm Operating speed at full rating For continuous lift or pull at maximum rating (1,000 lb.) with a 20% duty cycle, table at left highlights information for each power-drive type: Rate of lift or pull (rope speed) Power output needed (source, minimum) Recommended rope for capstan hoists Poly-Dacron or Composite Fiber Braided (consists of polyester fibers) shown in CHANCE Catalog Section Page 1153

4 Options and Components for 1,000-lb.-rated hoists All-Purpose Bracket For 1,000-lb. Series 90 hoists Includes two E P chain clamps for poles, angles, and beams C lb. (12 kg.) Wheel handles on chain binders make tightening easy. All-Purpose Bracket C Bolt-Down Bracket For 1,000-lb. Series 90 hoists Same as above, except does not include chain clamps E P 9 lb. (4.1 kg.) Hoi s t s - Powered To fit angle steel and beams, furnished bolts pin the clamps to form a 90 attachment shoulder. 1,000-lb. Bolt-Down Bracket E P Capstan Drum For 1,000-lb. Series 90 hoists Replacement, does not include mounting bolt or washer E P 7 lb. (3.2 kg.) To fit poles up to 23" in diameter, chain clamps pivot to automatically adjust. 1,000-lb. Capstan Drum E P Universal Bracket Recommended for gasoline 1,000-lb. hoist Also fits other 1,000-lb. Series 90 & earlier 750-lb. hoists Bolts down or uses two C Chain Clamps (below) for mounting on poles, angles and beams C Universal Bracket C Recommended for Gasoline hoist 13 lb. (5.9 kg.) Page 1154

5 Options and Components (continued) for 1,000-lb.-rated hoists Chain Clamp for Series 90 hoists One per Cat. No.; for All-Purpose or Bolt-Down Brackets E P Chain Clamp E P (Chains are 72" long.) 6 lb. (2.7 kg.) Chain Clamp for Universal Brackets only One per Cat. No., two required for C Bracket C /8 lb. (3.2 kg.) Chain Clamp C (Chains are 85" long.) Rope Lock Device for Series 90 hoists Includes mounting bolts and washers 2 lb. (0.9 kg.) Hoi s t s - Powered C Rope Lock Device C Must be ordered as a separate item. Includes 2 mounting bolts, washers and release lanyard. Accepts 1 2, 5 8 and 3 4 rope. Foot Controls for Series 90 hoists for 12-Volt DC drive C /2 lb. (1.6 kg.) for 115- and 230-Volt AC drive C T Foot Control with Guard P PK Foot Guard Kit for Hydraulic drive C lb. (1.8 kg.) 8 lb. (3.6 kg.) 4 lb. (1.8 kg.) C C lb. (10.9 kg.) Hydraulic Foot Control C Foot Guard Kit P PK Foot Control with Guard Kit P PK Page 1155

6 Swivel-Base Truck Mount for 12V, 115V & Hydraulic 1,000-lb. Sets at angles needed for variety of jobs Turntable design permits proper alignment without repositioning service vehicle Heavy-gauge steel base bolts directly to truck body wherever convenient Bracket can be pinned at 15-degree interval around circular base for: stringing, tensioning, and sagging conductors; pulling in cable; hoisting equipment; setting poles; and pulling vehicles! WARNING This is not a personnel lifting device. A label on the unit warns against lifting people or loads directly above people. To store hoist on C-bracket, simply remove four bolts. The C-bracket also can be bolted down for fixed-angle. Hoi s t s - Powered Utilize truck as portable power source Only 12V, 115V, 230V and Hydraulic 1,000-lb.-rated hoists are recommended for truck mounting See page 1153 to order Swivel Bracket C Swivel Bracket only C lb. (8.1 kg.) Swivel-Base Truck Mount T C-Bracket C Swivel Base Truck Mount (Assembled Swivel Bracket and C-Bracket at right) C-Bracket only complete with mounting bolts C lb. (2.3 kg.) T lb. (10.4 kg.) Weather Shield for 12-Volt DC hoist only complete with band clamp C lb. (0.5 kg.) Page 1156

7 Hitch-Receiver Mount for Swivel-Base Mount for 12V, 115V, 230V & Hydraulic 1,000-lb. Quick and convenient, fits 2 -square towing receivers Faster than any other method, job-ready mount puts capstan hoist in right position for pulling, stringing, and lifting jobs With hoist stored on it, mount s square tube simply inserts and pins in any 2 -square receiver of a Class III or IV towing hitch Specially designed for swivel-base mount T Hitch-receiver Mount features hole pattern specifically designed to fit Swivel-Base Mount T (for more details see page 1156) Swivel mount s turntable design permits proper alignment without repositioning service vehicle Swivel mount permits pinning bracket at every 15-degree interval around circular base for: stringing, tensioning, and sagging conductors; pulling in cable; hoisting equipment; setting poles; and pulling vehicles Utilize truck as portable power source Hitch-Receiver Mount is rated at 1,000 lb. to correspond with ratings of capstan hoists for which it is intended Only 12V, 115V and Hydraulic 1,000-lb.-rated hoists are recommended for truck mounting See page 1153 to order Description Weight T Hitch Mount for Capstan Hoist 21 lb. (9.5 kg.) PSC Hitch Mount with Swivel Base 62 lb. (28.1kg.) 1,000 lb. rating Hitch-Receiver Mount T as furnished PSC (Hitch Mount Bracket T with Swivel Base T ) Page 1157

8 MATERIAL HANDLER SPECIAL APPLICATION For AC, Hydraulic & Gasoline 1,000-lb. (Order hoists on page 1153) Application and Operation Portable system sets up fast where large vehiclemounted equipment is impractical Lifts tools, apparatus, sets poles, and moves materials in warehouse or store yard Automatically takes up rope on reel and keeps line out of dirt Mounts to wood, concrete, or steel poles and angle-member structures with one bracket and two chain clamps Operator can keep all activity in view while controlling lift with tension-adjustment knob and hoist s foot control Material Handler chassis only C Must order separately: C Bracket, for poles, beams or angles (page 1154) Two C Chain Clamps (page 1155) Poly-dacron or Polyester Braided Rope (Cat. Sect. 1250) 38 lb. (17.2 kg.) C H Take-Up Reel with handle (shown above; Capacity: 600 ft. x 1 2 " rope or 1,500 ft. x 3 8 " rope; Weight: 20 lb. / 9 kg.) Capstan Drum Tension Control Knob Level Wind Guide Rope Reel Idler Pulley Snatch Block Load Idler arm stores simply by moving wingbolt to another hole. Page 1158

9 3,000-lb. Load Rating 12V, 115V Hydraulic, Gasoline A m pe V Unit Electrical source requirements Electric Drive 115-Volt AC includes Power Hoist and Foot Control Switch only C Hydraulic Drive includes Power Hoist only; To order Foot Control Switch, see page With Bayonet for Collapsible Reel by others or Removable Capstan Drum C NOTE: Includes Power Hoist only. To order Foot Control Switch, see page Weight Hydraulic C lb. (20 kg.) 58 lb. (26.3 kg.) Weight Hydraulic Bayonet C lb. (16.4 kg.) Hydraulic Reversible C lb. (45.4 kg.) r e s Load pounds Components Four ½ mounting bolts furnished with each unit Mounting flange provides eight ½ tapped holes on 5-5/8 bolt circle Recommended rope for use with capstan hoists are Poly-Dacron or Composite Fiber Braided (consists of polyester fibers) as shown in CHANCE Catalog Section 1250 Series 90 3,000-lb. Hoist Rope Speed for 3,000 lb. load Source Required to meet Rope Speed Rate 115-Volt AC 12 feet per minute 14 amperes motor current Hydraulic 30 feet per minute 8 gal. per min. & 1,000psi Gasoline 11 feet per minute Engine speed: 7,000rpm Operating speed at full rating For continuous lift or pull at maximum rating (3,000 lb.) with a 20% duty cycle, table at left highlights information for each power-drive type: Rate of lift or pull (rope speed) Power output needed (source, minimum) With Bayonet for Collapsible Reel by others or Removable Capstan Drum C ordered separately, page Gasoline Drive 18" W NOTE: Includes Power Hoist and Bolt-Down Bracket. To order Foot Control Switch, see page includes Power Hoist and Foot Throttle Control only Gasoline unit features 35 cubic-centimeter 4-cycle engine. C "L 58 lb. (26.3 kg.) 10" H Recommended rope for capstan hoists Poly-Dacron or Composite Fiber Braided (consists of polyester fibers shown in CHANCE Catalog Section 1250 Page 1159

10 Options and Components for 3,000-lb.-Rated Hoists All-Purpose Bracket For 3,000-lb. Series 90 hoists Includes two E P chain clamps for poles, angles, and beams C lb. (14.5 kg.) All-Purpose Bracket C Wheel handles on chain binders make tightening easy. Bolt-Down Bracket For 3,000-lb. Series 90 hoists Same as above, except does not include chain clamps E P 14 lb. (6.4 kg.) To fit angle steel and beams, furnished bolts pin the clamps to form a 90 attachment shoulder. 3,000-lb. Bolt-Down Bracket E P Capstan Drum For 3,000-lb. Series 90 hoists Replacement, does not include mounting bolt or washer E P 11 lb. (5 kg.) 3,000-lb. Capstan Drum E P Page 1160

11 Options and Components (continued) for 3,000-lb.-rated hoists " Bayonet Adapter retrofits on 3,000-lb. standard Hydraulic hoist for collapsible reel or C drum C lb. (2.2 kg.) Bayonet Adapter C " Capstan Drum Removable for 3,000-lb. hoist w/bayonet; " dia. x " length; on and off w/out tools C lb. (5.4 kg.) Removable Capstan Drum C Chain Clamp One per Two required for All-Purpose or Bolt-Down Brackets E P Rope Lock Device for Series 90 hoists Includes mounting bolts and washers C Foot Controls for 115-Volt AC drive C T Foot Control with Guard P PK Foot Guard Kit for Hydraulic drive C for Gasoline drive T for Series 90 hoists 6 lb. (2.7 kg.) 2 lb. (0.9 kg.) for Series 90 hoists 4 lb. (1.8 kg.) 8 lb. (3.6 kg.) 4 lb. (1.8 kg.) 24 lb. (10.9 kg.) 2 lb. (0.9 kg.) Chain Clamp E P (Chains are 72" long.) Rope Lock Device C Must be ordered as a separate item. Includes 2 mounting bolts, washers and release lanyard. Accepts 1 2, 5 8 and 3 4 rope. Foot Guard Kit P PK Foot Control with Guard Kit P PK C Hydraulic Foot Control C Page 1161

12 210 N. Allen St. Centralia, MO (573) NOTICE: For the latest revision of our Catalog and Literature, click here or visit our web site: NOTE: Hubbell has a policy of continuous product improvement. Please visit hubbellpowersystems.com to confirm current design specifications. Copyright 2018 Hubbell Incorporated NEVER COMPROMISE JULY 2018 Page 1162 Catalog 1150