black light blue white N51003 red Nova Reproduction Convertible Top Boot

Transcription

1 Convertible Tops If you re looking for an authentic reproduction of the original convertible top then look no further! We offer only the highest quality reproduction on the market today! Your early Chevy II deserves only the finest top available which is manufactured with a heavy duty satin backed material produced in the original grain. Each reproduction convertible top is guaranteed against peeling, cracking or shrinking for 36 months. You can now obtain an original appearance for your early Chevy II/Nova and maintain originality by installing a Classic Industries reproduction convertible top. Available in black or white. Professional installation recommended Convertible Well Liner Excellent reproduction liner covering the section between the rear seat and trunk area. Used in section where convertible top folds down into well area. Produced from factory patterns using top grade heavyweight sateen backed vinyl material. Note: The sateen side faces away from the rear window when installed. N black ea Plastic Rear Window Assembly Replace your convertible rear plastic window with this reproduction which includes the outer matching vinyl. The rear plastic window assemblies are manufactured by the OEM GM supplier. This rear curtain assembly includes the original style marking: Regalite with a diamond outline and the production date of the window. Note: Window will contain current production date. Not the original production date of your vehicle. N white ea Convertible Top With Plastic Rear Window This rear curtain assembly includes the original style marking Regalite with a diamond outline and the production date of the window. If you want an original appearance along with factory quality this is the top you want! This original appearance convertible top will replace the original to exact factory specifications. Includes rear plastic window Note: Window will contain current production date. Not the original production date of your vehicle. N black ea N white ea Top Boot Storage Bag Protect your convertible top boot when it s off the car by using a sensible storage technique. The storage bag will help protect your vehicles top boot while being stored in the trunk or your garage. The bag is large enough to keep your top boot in fresh, usable condition. Available in black only. K ea Convertible Top Pads Replace your old top pads when replacing your convertible top. Each pad is original in appearance and quality. Includes cloth padding with cloth covering. Used as reinforcement between convertible top and top frame. K pr black bright red light blue aqua white saddle Body Components H N Nova Reproduction Convertible Top Boot Exact reproduction convertible top boot is manufactured using the exact factory patterns for a great fit! Each top boot is produced using the original correct grain vinyls. Includes a complete set of snaps for easy installation and special stiffeners which help maintain the original shape of the boot and give added support when in use. Each boot is manufactured with a thick foam backing which gives the boot padded support. Top boots are available in virtually every original factory interior color. N black ea N bright red ea N light blue ea N aqua ea N white ea N saddle ea N red ea N fawn ea OER Top Secret Top Care Formula OER Top Secret is a complete system for the care of canvas tops. It consists of a heavy-duty cleaner that safely removes the toughest soils and stains with an exclusive formula that will not harm automotive finishes. The canvas formula includes the top cleaner and our exclusive canvas UV protectant that repels water and stains. OER Top Secret Kit Canvas Formula K89457 cleaner and protectant kit OER Top Secret Components K oz. bottle top cleaner ea K oz. canvas protectant ea 206 Convertible Tops Toll Free Order Line red fawn

2 Convertible Top Parts Convertible Top Binding End Clip Reproduction of the top rear binding end clip for convertible models. These stainless steel covers finishes both ends of the rear window outer top bow binding trim strip required ea Convertible Top Molding Clips A reproduction of the clip that attaches the molding around the rear well section on Chevy II/ Nova convertible models. Note: 12 required per vehicle. Sold individually, or in a money saving kit of individually ea K kit of kit Motor Pump Assembly OE style replacement motor and pump assembly. Features original style and locations for electric and fluid connections. HK OE style ea Convertible Top Cylinder After years of use the original cylinders will wear out. Replace them with new, not rebuilt, replacements. Manufactured out of aluminum, the appearance is slightly different from the original, but it will function and operate exactly the same. Sold individually. Two cylinders are required per vehicle. HK235A ea Hydraulic Hose Set Finding original hose for your early Chevy II convertible is next to impossible. If you own a convertible model with a power top, this set is what you need to put it back to original working condition. Each set comes complete with the hoses which run from the pump assembly to the lift cylinders along with all the fittings necessary for installation. HK set CM2148 CM Convertible Top Latch Reproduction convertible top latch assemblies for Chevy II/Nova convertible models. These exact reproductions will install as original and are manufactured in the USA. Very high-quality and Officially Licensed by GM. CM LH ea CM RH ea CM2148A screws (4 req.) 1.99 ea Convertible Latch Knuckle Hook Reproduction of the hook used to hold down the convertible top. Screws directly into the convertible latch knuckle assembly. Sold individually. Two hooks required per vehicle ea Convertible Motor Grommet Reproduction rubber mounting/insulation grommet for Chevy II/Nova convertible models. Rubber grommet installs on the pump assembly and secures it to the vehicle, while creating a damper for noise and vibration when the pumo is in operation ea Convertible Top Hose Clip Reproduction convertible top hose retainer clip for Chevy II/Nova convertible models. This reproduction retainer holds the top hose to the body, keeping the hoses out of the way and allowing the hoses to move with the top cylinders. This prevents the hoses from pinching and interfering with the operation of the cylinders ea Convertible Top Cables Replace your stretched or broken convertible top hold down cables with these fine reproductions for Chevy II/Nova convertible models. Sold in pairs pr Top Cylinder and Hose Kit Reproduction convertible top cylinders and a set of hoses. Each item is also available separately. Buy the kit and save. R kit Convertible Top Latch Bushings This is a reproduction of the bushings that are in the convertible top latches on Chevy II/Nova convertibles. These are the bushings that act as guides for the convertible top when they go into the latch. Comes with retainers. CM2147A pr 3M Heavy Duty 20 Spray Adhesive 3M Heavy Duty 20 Spray Adhesive forms a powerful, permanent bond to wood, laminate, metal, plastic and more. Simply spray the adhesive on one or both surfaces, wait 15 seconds to 30 minutes, and press surfaces together to form a tight bond. Our self-contained, highly portable dispenser allows for a variable width lace spray pattern to help ensure precise placement Heavy Duty oz. can ea Body Components H Convertible Top Components 207

3 Bumpers & Components Front Bumper Reproduction chrome front bumper for Chevy II/Nova models. Replace the old damaged or pitted bumper with this all new reproduction. Each bumper features quality chrome-plating A OER Authorized ea B OER Premier ea Front Bumper Filler Panel Reproduction of the front bumper filler panel for Chevy II/Nova models, manufactured to exact specifications. C ea 1965 Front Bumper Reproduction chrome front bumper for 1965 Chevy II/Nova models. Replace the old damaged or pitted bumper with this all new reproduction. Each bumper features quality chrome-plating A 1965 OER Authorized ea B 1965 OER Premier ea Front Bumper Filler Panel Reproduction filler panel insert between the grill and bumper filler reinforcement above the front bumper on Chevy II/Nova models plastic ea Front Bumper Reproduction chrome front bumper for Chevy II/Nova models. Replace the old damaged or pitted bumper with this all new reproduction. Each bumper features quality chrome-plating A OER Authorized ea B OER Premier ea Front Bumper Filler Panel Reinforcement Reproduction front bumper filler panel reinforcement for models, manufactured to exact specifications. C ea Front Bumper Reproduction chrome front bumper for Chevy II/Nova models. Replace the old damaged or pitted bumper with this all new reproduction. Each bumper features quality chrome-plating A OER Authorized ea B OER Premier ea Rear Bumper Reproduction of the chrome rear bumper for Chevy II/Nova models. Each bumper is manufactured to exact factory specifications. Will replace the original exactly. Features a high-quality chrome finish A ea Body Components H A Front Bumper Reproduction chrome front bumper for Nova models. Replace the old damaged or pitted bumper with this all new reproduction. Each bumper features quality chrome-plating A OER Authorized ea B OER Premier ea Front Bumper Filler Panel Superb reproduction of the bumper filler panel for Chevy II/Nova models. Manufactured to exact specifications for a factory fit. C ea Rear Bumper Reproduction of the highly sought after Chevy II/Nova rear bumper. Features a high-quality chrome polished finish A OER Authorized ea B OER Premier ea Rear Bumper Reproduction of the highly sought after Nova rear bumper. Features a high-quality chrome polished finish A OER Authorized ea B OER Premier ea 208 Bumpers & Components Toll Free Order Line

4 Bumpers & Components RP5038 F13060 RP5045 RP5044 F13560 RP5037 RP Fiberglass Rear Bumper F14560 These fiberglass replacement bumpers offer the ultimate in lightweight durability while retaining an original appearance. Excellent for race car use. Note: Not for use with OEM brackets. Shipped double oversize. F ea F ea F ea RP5042 RP Bumper Filler Replacement fiberglass bumper fillers for Nova models. It is recommended you replace all pieces of the bumper filler for a better bumper fit. Note: *Shipped oversize. **Shipped double oversize. Front Bumper Fillers RP left ea RP center ea RP right ea RP left ea RP right ea Rear Bumper Fillers RP5037 ** 1974 complete ea RP left ea RP center ea * RP right ea Front Bumper Guards Reproduction of the front bumper guards for models. These feature a beautiful chrome finish and are manufactured to exact specifications for a perfect fit. Mounting hardware included. N pr F Fiberglass Front Bumper F13550 F14550 These fiberglass replacement bumpers offer the ultimate in lightweight durability while retaining an original appearance. Excellent for race car use Important: *Though originally designed for 1965 models, this bumper will fi t models. **For models must use park lamps # All bumpers are not for use with OEM brackets. F13050 * 1965 will fit ea F ea F14550 ** ea Front Bumper Guard Cushions Reproduction of the front bumper guard inserts that were factory installed on Nova models with bumper guards. These cushions will replace your originals exactly and add a new appearance to your original bumper guards pr Rear Bumper Guard Cushions Reproduction rear bumper guard inserts for Nova models with bumper guards. These cushions will replace your originals exactly and add a new appearance to your original bumper guards. K pr Body Components H Bumpers & Components 209

5 Bumper Brackets This reproduction body seal is manufactured to exact factory specs and includes correct confi guration allowing a perfect fi t for this sensitive area Front Outer Bumper Brackets Reproduction front outer bumper brackets for Chevy II/Nova models. Manufactured to original specifications, each bracket will install as original. Note: Mounting hardware available separately. P pr close up of correct confi guration for rear bumper to body seal Rear Bumper to Body Seal Excellent reproduction body seal strip used to seal and fill the area where the rear bumper meets the body. This often damaged or missing part should be replaced to keep any water or other elements out. K ea ea Front Inner Bumper Brackets Reproduction front inner bumper brackets for Chevy II/Nova models. Sold in pairs. P inner brackets pr Bumper Bolt Set NB6272 Replace worn out or rusted bumper bolts with these reproductions. Each set contains stainless steel bolts. GM front and rear bumper bolt set 2 sets req set GM bumper bracket mounting set 2 sets req set GM front and rear bumper bolt set set NB front and rear bumper bolt set set Front Bumper Brackets Reproduction front bumper brackets for Chevy II/Nova models. Sold in pairs. N pr Rear Bumper Brackets This is a top quality reproduction of the rear bumper brackets on Chevy II/ Nova. These stamped steel, EDP coated brackets feature precise bends and mounting holes, they will fit and function like new. P pr Body Components H Outer Front Bumper Brackets These brackets are just what you need to remount your Chevy II/Nova front bumper. They are manufactured to replace the originals exactly. Sold in pairs. N pr Front Bumper Brackets N2337 Reproduction front bumper brackets for Chevy II/Nova makes replacing your damaged bumper easy. Correct stamped steel brackets with all the proper mounting holes in correct locations. Each side consists of two brackets. Sold in pairs for each side. N LH 2 piece pr N RH 2 piece pr N LH and RH brackets 4 piece set kit Rear Bumper Bracket Bumper brackets bent or rusted? These are authentic looking reproductions of the rear bumper brackets for Chevy II/Nova. These stamped steel brackets have the correct contours and will mount your rear bumper in the correct location LH ea RH ea Rear Bumper Bracket Reproduction rear bumper brackets for Chevy II/Nova makes replacing your damaged bumper easy. Correct stamped steel brackets with all the proper mounting holes in correct locations LH ea RH ea 210 Bumper Brackets & Components Toll Free Order Line

6 License Components K License Plate Attachment Screw & Nut Kit Original type replacement screw and nut kits for the license plate bracket. The nylon nuts push into the bracket and screws secure the plate to the bracket. K piece 5 screws, 5 nuts kit K piece 2 screws, 2 nuts kit Rear License Lamp This reproduction license lamp assembly includes: bracket, lens and wiring. Assembled and ready to install. Fits all Chevy II/Nova except station wagon ea Rear License Bracket Correct reproduction rear license bracket. Installs on the rear and covers the gas cap. The license plate attaches to this bracket, also known as the gas tank fuel filler door ea B ea ea K132 B1019 A License Plate Rubber Bumper Reproduction rubber bumper originally installed on Nova models. This bumper will keep the plate bracket from rubbing against the body, causing damage. K piece set A piece set Chrome-Plated License Plate Bolt Set Dress-up your Nova with these one of a kind dressup bolt sets. The Chevrolet Bow Tie logo is stamped directly onto the head of these chrome-plated bolts D set WE310 head detail WE License Lamp Socket And Wiring Wiring is often overlooked as being the cause of a malfunctioning light bulb. Replace the corroded license plate lamp socket in your Nova with this original style reproduction socket. Includes enough wiring for easy splicing into the harness. WE ea WE ea Rear License Lamp Quality reproduction license lamp assembly for Nova models. Features the original markings for authenticity ea Rear License Plate Stoppers OER reproduction license plate stoppers for the rear license bracket on Nova pr License Plate Installation Nut Correct nuts used to attach the license plate to the bracket on models. A ea Rear License Lamp This reproduction license lamp assembly includes bracket, lens, and wiring. Assembled and ready to install. Fits all except station wagon. C ea License Lamp Gasket This reproduction gasket is important to keep rain or other elements from entering into the lens. W ea License Lamp Lens This is a reproduction of the license lamp lens on Chevy II/Nova models. Replace your broken or faded lens today. This lens is correct in every way and is easy to replace. CM ea ea License Lamp Gasket Correct reproduction gasket for Chevy II/ Nova. Fits between the license lamp lens and base. This reproduction gasket keeps the rain or other elements from entering into the lamp. K ea Body Components H License Plate Parts 211

7 Chevy II/Nova Grills 1962 Nova Standard Grill Reproduction of the 1962 Chevy II/Nova standard grill. Each grill features the correct end contours conforming to the headlamp bezels offering a clean fit and appearance. Note: Shipped oversize ea 1966 Nova Standard Grill Reproduction of the highly sought after 1966 Chevy II/Nova grill. Each grill features the correct end contours that conform to the headlamp bezels offering a clean fit. Note: Shipped oversize ea 1963 Nova Standard Grill Reproduction 1963 Chevy II/Nova standard grill. Each grill features the correct end contours conforming to the headlamp bezels offering a clean fit. This grill includes the upper brace and the vertical braces attached with the correct rivets. Note: Shipped oversize ea 1967 Nova Standard Grill Reproduction of the highly sought after 1967 Chevy II/Nova grill. Each grill features the correct end contours conforming to the headlamp bezels offering a clean fit and appearance. Note: Shipped oversize ea Polished Billet Aluminum Grill Add a little style to your Chevy II/Nova with these finely polished billet aluminum grills. Made with uncompromising standards and quality workmanship. Feature original style cut outs where necessary for hood latch or signal lamps. Note: Shipped oversize ea ea ea OE style ea without hood latch cutouts ea without hood latch and lamp cutouts ea ea Nova Standard Grill Reproductions of the Chevy II/Nova grill. This grill is meticulously manufactured to give an authentic and original appearance when installed. Note: Shipped oversize ea Nova SS Grill Reproductions of the Nova Super Sport grill. This grill is meticulously manufactured to give an authentic and original appearance when installed. Note: Shipped oversize ea Body Components H 1964 Nova Standard Grill Reproduction 1964 Chevy II/Nova standard grill. Each grill features the correct end contours conforming to the headlamp bezels offering a clean fit. Includes the upper brace and the vertical braces attached with the correct rivets. Note: Shipped oversize ea 1965 Standard Grill Reproduction of the 1965 Chevy II/Nova standard grill. Each grill features the correct end contours conforming to the headlamp bezels offering a clean fit and appearance. Note: Shipped oversize ea Standard Grill Reproductions of the Nova standard grill. This grill is meticulously manufactured to give an authentic and original appearance when installed. Note: Shipped oversize ea Nova SS Grill Reproduction Nova Super Sport grill which is meticulously manufactured to give an authentic and original appearance when installed. Note: Shipped oversize ea 212 Grills Toll Free Order Line

8 Chevy II/Nova Grills Nova SS Grill Quality reproduction of the SS grill for Nova Super Sport models. Painted black, the grill features the two horizontal bars in argent silver found on Super Sport model grills. Note: Shipped oversize. N ea 1966 Lower Grill Molding Reproduction lower grill molding for 1966 Chevy II/Nova models. N lower ea Nova Standard Grill Reproduction of the original grill for standard Nova models. This injection molded plastic grill is manufactured to factory specifications for a perfect fit and appearance. Note: Shipped oversize standard ea Highly Sought After Rally and SS Grill Designed to Replicate the Original in Every Detail! Grill Brackets OER reproduction grill mount brackets for Chevy II/Nova grills. Brackets are manufactured from stamped steel and EDP coated for rust prevention pc set pc set pc set pc set Grill Mounting Brackets Reproduction grill mount bracket set for 1966 Chevy II/Nova makes replacing your damaged grill easy. Correct stamped steel brackets with all the proper mounting holes in correct locations. A piece set Nova SS/Rally Grill OER reproduction of the rare and highly sought after Rally and SS grill to fit Nova models with Rally or SS option. Each grill is designed to mount on Nova models equipped with the Rally grill brackets. Black grills were original equipment on the 1976 SS Nova, but will also fit the Nova with Rally option. Injection molded, chrome-plated and then painted black in the diamond patterned center, the OER Rally/SS grill was designed to replicate the original in every detail. Includes hardware. Note: Shipped oversize SS black ea Rally chrome ea Grill Attaching Rivet with Nut Grill attaching rivet with nut for various applications where a rivet is needed. These have the look of a rivet with the ease of a bolt and nut. Available in silver zinc or black EDP coated. Individual silver zinc pr black EDP pr Set of silver zinc set black EDP set Upper Grill Reinforcement Reproduction upper grill reinforcement panel for Nova models. Manufactured to factory specifications featuring original style contours, pre-punched mounting holes and EDP coated for rust prevention ea Chrome Grill Guard Reproduction of the optional Chevy II/Nova grill guard. This reproduction is installed using existing bumper bolt holes. Beautiful reproduction of the original optional chrome grill guard. Note: Shipped oversize ea Grill Nut Replacement grill nut for Nova models. These are the correct style replacement grill attachment nut ea ea Nova Grill Support Bracket Reproduction grill support brackets for all Nova models. These stamped steel brackets attach to the radiator support and provide the grill with a mounting point on each end LH ea RH ea Body Components H Grills 213

9 Headlamp Bezels Chevy II/Nova Headlamp Bezel Exact reproduction aluminum headlamp bezels installed on Chevy II/Nova models. Manufactured to original GM specifications for a perfect fit and original appearance. Your choice of LH or RH bezels. We recommend replacing both bezels to get a matching original appearance LH ea RH ea 1968 Chevy II/Nova Headlamp Bezels Replace your original 1968 Chevy II/Nova headlamp bezels with this quality reproduction manufactured to exact factory specifications. Each bezel will install and fit as original bringing back a factory fresh appearance. Sold in pairs. Note: Each bezel features a chrome fi nish around the headlight and 7 horizontal chrome fi ns to mate with 7 chrome accents on grill as original for all standard Nova models. For SS models, refer to part # LH and RH pr SS LH and RH pr Manufactured with original GM Tooling! 1965 Chevy II/Nova Headlamp Bezel Exact reproduction headlamp bezels designed for 1965 Chevy II/Nova models. These aluminum headlamp bezels are manufactured to factory specifications for an original appearance and fit. 2 required per vehicle required ea 1966 Chevy II/Nova Headlamp Bezel OER manufactures this beautiful reproduction to exact factory specifications. Manufactured in brightly polished aluminum unlike other inferior reproductions. The headlamp bezels will fit either LH or RH sides. This is truly one of the most desirable parts for the 1966 Chevy II/Nova. Guaranteed to fit and look perfect required ea Nova Headlamp Bezel OER Premier and Restorer s Choice TM headlamp bezel for Nova models are die-cast to exact factory specifications for an authentic fit and original appearance. Headlamp Bezels chrome-plated, polished to perfection, then accented with black paint in all of the correct original locations. Each bezel mounts to the vehicle with phillips head screws (not included) to provide a finished appearance around the sealed beam headlamp. Hardware not included, sold separately (1 set attaches both bezels). Made in USA! Note: Not for use on 1969 models originally equipped with optional headlight washers. Original GM Tooling LH ea RH ea Restorer s Choice TM C LH and RH pr Standard Replacement C1671A LH and RH pr Hardware Set set required per car set Body Components H Chevy II/Nova Headlamp Bezel Replace your original headlamp bezels with these OER replacements manufactured from original GM tooling. Be sure to replace the headlamp bezel seals when replacing the bezels for a tight and secure fit LH ea RH ea K headlamp bezel seals pair pr Nova Headlamp Bezel OER reproduction headlamp bezels for Nova models. Each bezel is injection molded to exact specifications. Standard Models Silver LH ea RH ea Super Sport Models Black LH ea RH ea Rally Models Black LH ea RH ea Concours Models Chrome LH ea RH ea 214 Headlamp Bezels Toll Free Order Line

10 Headlamp Components N62102 K Headlamp Bucket Shields Replace your commonly rusted metal headlamp bucket shields with these excellent plastic reproductions. They can be painted any color to match your classic Chevy II/Nova. Note: Sold in pairs only. C LH and RH pr K892 N Headlamp Bucket Housing Reproduction headlamp bucket housings for 1966 models. These housings attach to the radiator support and hold the headlamp components in place. N LH ea N RH ea Headlamp Mounting Bucket Reproduction headlamp mounting buckets which are designed to secure the headlamp sealed beam in position. These buckets attach to the headlamp housing using adjustment screw and nut assemblies. Note: On applications the buckets are reversed K893 is LH and K892 is RH. K LH ea K RH ea K LH ea K RH ea Headlamp Filler Panels Reproduction headlamp filler panels (headlamp mudcaps). These reproductions will replace the original aluminum style filler panels which are commonly bent, N corroded or missing. Installs directly on either side of the radiator support assembly covering and protecting the area directly behind the headlamp assemblies. A LH and RH pr N Headlamp Bucket Housing Reproduction headlamp bucket housings for 1967 models. These housings attach to the radiator support and hold the headlamp components in place. N LH ea N RH ea G Headlamp Mounting Bucket These headlamp mounting buckets are designed to secure the headlamp sealed beam in position. These buckets attach to the headlamp housing using adjustment screw and nut assemblies LH or RH repro ea G LH or RH GM ea Fender Moldings Correct replacement moldings for headlamps. This molding attaches to the front fender surrounding the headlamp area. Manufactured in polished aluminum. Will fit correctly and add new life to your headlamp area. Also commonly known as the eyebrow molding. Sold in pairs only. Mounting hardware not included. Note: Eight 3/16"-24 nuts required for installation. K LH and RH pr Body Components H Headlamp Components 215

11 Headlamp Components Headlamp Bulb Replacement sealed headlamp bulbs Tungsten 7" round ea H Halogen 7" round ea H Halogen rectangular ea MX09137 MX09124 Diamond Cut Headlamp Unique looking halogen diamond cut headlamps for increased visibility, safety and a unique custom look. These headlamps install much like a standard sealed beam unit, but allow the use of an H4 Halogen bulb in your choice of color. The diamond cut reflector concentrates the beam on the road in front of you. Sold separately. For 2 headlamp system. Note: For your conversion, we recommend using our wiring harness upgrade kit sold separately. MX " round ea MX " x 6" rectangular ea 1149 CP " Crystal Headlamp Bulb w/auxiliary LEDs These crystal headlamps with auxiliary LEDs give your classic ride a modern look. The aluminum reflector is a reinforced, multi-faceted design for maximum vibration resistance. A HB2/ /55W 12V halogen bulb replaces H6017/H6024 bulbs to meet DOT/SAE standards, Choose from 10 or 34 LED auxiliary lighting. 10 LED Bulb CP amber LEDs ea 34 LED Bulb CP amber LEDs ea CP white LEDs ea profi le CP " High Power 11 LED Crystal Headlamp This 7" crystal headlamp uses eleven high power LED to improve visibility, providing a white light similar to daylight. An impact resistant polycarbonate lens provides unparalleled protection from road hazards, while the solid state design resists shock and vibration. Meets SAE/DOT FMVSS108 standards. CP ea chrome housing black housing Projector Style Headlamps Embody the classic look while substantially upgrading the quality and spread of light! The unique hi-low switch design provides a clean and safe light cutoff design, eliminating the issue of headlight dazing on the roads. Each unit features a 42mm Bi-Xenon projector (high and low beams) with adjustable light focus and flat light distribution to prevent blinding of oncoming traffic. Available with a traditional chrome housing or with a black housing and city light built into the unit. Bulbs and wiring included " round chrome housing pr " round black housing pr " x 6" chrome housing pr " x 6" black housing pr Chrome Headlamp Half Shields Keep your headlamps clean while adding a custom chrome appearance. The chrome headlamp shields attach to the upper portion of the headlamp and offer a custom look. For round 7-1/2" diameter headlamps. T pr Body Components H 1149 profi le 1179 profi le Halogen/Xenon Headlamp These conversion headlamps feature lead crystal lens with E mark certified precision optics, steel stamped reflector and self-sealing rubber boot to protect the optic unit from dust and moisture. They are equipped with halogen H4 60/55W or xenon hyper white bulbs, which are 50% brighter than standard halogen bulbs, for superior performance. Your choice of classic looking convex lens or more modern looking flat lens. Applications to fit four headlamp or two headlamp systems. 7" Classic Convex Lens High/Low Beam for 2 Headlamp System 1179 Halogen ea 1179X Xenon ea 7" Modern Style Flat Lens High/Low Beam for 2 Headlamp System 1149 Halogen ea 1149X Xenon ea profi le Tri-Bar Custom Headlamp Add a new look to your classic car with these custom headlamps. Manufactured with a metal housing and glass lens to meet high-quality standards. The 7" lamp features an inner one piece chrome glare shield with black chrome-plated center dot, and flat style lens. Dust boot and clear halogen bulb included with each lamp " flat glass ea un-lit lit-up LED Powered Headlamps Powerful LED CREE technology combined with Delta Tech s Prismatic lens and flawless parabola delivers unmatched power, clarity and near daylight illumination at 1900 Lumen at both high and low beam, while drawing only 2 amps per light. Each unit features an additional LED bulb that can be wired as a driving light, turn signal, park lamp or even as a mood light. Available in your choice of classic looking convex lens or modern style flat lens. Applications to fit two or four headlamp systems. 7" Classic Convex Lens High/Low Beam for 2 Headlamp System with amber blinker pr with white blinker pr 7" Modern Style Flat Lens High/Low Beam for 2 Headlamp System with amber blinker pr with white blinker pr 216 Headlamp Components Toll Free Order Line

12 Headlamp Components H4 Conversion Lamp Provide your new H4 s with maximum power and decrease the chance of overloading (and possibly melting) your thin stock wiring and headlamp connectors. Power will be drawn directly from your battery, eliminating voltage drops and ensuring headlight system reliability. Installs easily in minutes without any cutting or splicing. Simply plug into your factory headlight sockets, attach positive connectors to battery terminal and ground wires to the body of your vehicle. Two 30 amp relays provide added protection for your headlight switch and wiring harness. MX01132 for 2 headlamp system set Halogen Headlamp Harness To get maximum power from your LHH4 HID HeadLamp Bulbs HID headlamp bulbs are much brighter than conventional halogen bulbs, while providing tight light focus for better light distribution. They require 35 watts and use an external regulator, but will plug into the existing light plug. The H4 series bulb features a bright white HID low beam and a halogen high beam function. Important: Not for use on public roads. LHH4 H4 6000k white set headlights, it is recommended to have the shortest possible distance between the power source and the bulbs. Resistance in small gauge wire or in the switch will lower the output at the lamp. Our headlamp harnesses draw power directly from the battery, through a relay, to the headlamps, providing full power to your H4 conversion headlamps or Halogen sealed beams. They are made with TXL high temp wire, weather resistant 30 amp fuse, and two 40 amp weather resistant relays capable of handling up to 150 watts. With Two Headlamp System for 9004/9007 bulbs ea With Four Headlamp System for 9005/006 bulbs ea Relay and Fuse Assembly Protect your investment with this 5 prong 30 amp relay and 20 amp fuse set with 14 gauge wire leads relay/fuse ea Auxiliary Light Relay Set Install extra driving or fog lights easily and properly with our Auxiliary Light Relay Set. Switch can be wired to turn lights on per state law requirements: low beams and auxiliary lamps, high beams and auxiliary lamps, Auxiliary lamp operation only. Set includes: lighted switch, wiring harness, 30 amp relay and terminals set H4 Adapter Plug Set with Wires This plug is designed to adapt the factory 2 prong high beam headlamp plug to fit the upgraded halogen or xenon 3 prong bulbs adapter ea WE303 WE Headlamp Socket and Wiring A molded plastic socket used to connect the headlamp bulb. The socket has wire leads and connects the bulb to the power source. Fits Nova models. WE prong ea WE prong ea Plastic Wire Gutter This OER reproduction wire gutter is used to hold the engine harness as it passes against the firewall area and protects your wiring from falling into the distributor area. Each wire gutter is pre-cut to the original length assuring originality. Also includes pre-punched mounting holes for easy installation. This extremely durable item replaces your original painted over, heat warped, or missing wire gutter ea Headlamp Beam Adjusting Spring Adjusting spring for headlamps. These headlamp springs allow your headlight beams to pivot for the proper alignment LH or RH ea LH ea A OER Headlamp Retaining Ring Reproduction headlamp retaining ring for models. Replaces the original damaged retaining ring LH or RH ea LH or RH ea A screw 6 piece set G retaining screw-6 req 3.99 ea G8971 G7842 G Headlamp Retaining Ring The GM rings are of a current design and are used as a replacement part and may differ cosmetically from the originals. G LH or RH ea G retaining screw 8 req ea C1403 C Headlamp Adjusters The correct hardware will make your installation easier, and give your classic a finished look. We offer replacement headlamp adjuster sets for Chevy II/Nova models. All sets include adjusters for both right and left sides. C set C kit Body Components H Headlamp Components 217

13 Side Marker Lamps CM4520 CM Front Marker Lens Gaskets Reproduction of the gaskets used to seal the side marker lamp and bezel to the body. Note: gaskets are for bezels without engine size designation. N front w/o engine size 3.99 pr CM4522 N Side Marker Lamp Kit Replace your front and rear side marker lamp assemblies with this easy to install kit which provides a set of side marker lamp assemblies. Each kit includes: four side marker lenses, two rear side marker lamp bezels and two reproduction front side marker bezels which feature the engine size. Note: The R5012 and R5012A include standard front chrome bezels which do not feature an engine size designation. N with kit N with kit N with kit N with kit N with kit R without engine size kit CM4523 CM Front Marker Lamp Bezels Reproduction of the chrome side marker bezels for the front fender. Bezel inserts directly over the lens assembly Note: 1 pair required per vehicle. CM pr CM pr CM pr CM pr CM pr Side Marker Lamp Gaskets Correct replacement gaskets for the rear side marker lamps. Will eliminate leakage due to rain, car washing or other elements. K rear pr Front Side Marker Bezel Gaskets Reproduction side marker bezel gaskets for Nova models. Mounts between the bezel and the body on the front side markers bezels with engine size designation. K pr Side Marker Lamp Gaskets Correct reproduction side marker gaskets for Nova models. These OEM style gaskets are stamped from rubber and include the correct contour. K replacement style (4) 3.99 set rubber style (4) set Body Components H N5026A 1969 Side Marker Lamp Kit Replace your front and rear side marker lamp assemblies with this easy to install kit which provides a set of side marker lamp assemblies. Each kit includes: four side marker lenses, two rear side marker lamp bezels and two reproduction front side marker bezels which feature the engine size. Note: The R5012 and R5012A include standard front chrome bezels which do not feature an engine size designation. N5022A 1969 with kit N5023A 1969 with kit N5024A 1969 with kit N5025A 1969 with kit N5026A 1969 with kit R5012A 1969 without engine size kit Side Marker Bezel Reproduction of the correct chrome side marker bezel for the front fender without an engine size. K ea WE Side Marker Lamp Socket Replacement side marker lamp socket with wire pigtail. Fits front or rear marker lamps on all Chevy II/ Nova models. WE reproduction ea G Delco ea 218 Side Marker Lamp Kits Toll Free Order Line

14 Side Marker Lamps medallion (lens and bezel sold separately) Custom Side Marker Medallions Laser cut from mirror polished stainless steel, these Bow Tie medallions mount with double sided tape between the side marker lens and the bezel for a cool, custom look. Includes medallions only. Two pair required per vehicle. Note: Bezel and lens not included pr Rear Side Marker Lenses Reproduction rear quarter panel side marker lamps. These lamps include a red lens assembly attached to the housing. Classic Industries maintains the highest standards of quality. Sold in pairs red pr 1969 Front Side Marker Lens Replacement front side marker with amber lens attached to the housing. This lens was used on several 1969 Chevrolet models. Note: Gaskets sold separately. CMA amber ea Front Side Marker Lens Reproduction side marker lamp originally installed on Nova models. Each lens features original markings when required. Note: Gaskets sold separately front ea 1968 Front Side Marker Lens Replacement front side marker with clear lens attached to the housing. This lens was used on several 1968 Chevrolet models. Note: Gaskets sold separately. K clear ea Side Marker Lamp Kit Replace your front and rear side marker lamp assemblies with this easy to install kit. Each kit includes: the lens and the housing, along with all four high polished chrome bezels. N kit Rear Side Marker Lens Reproduction side marker lamp originally installed on Nova models. Each lens features original markings when required. Note: Gaskets sold separately rear ea Rear Side Marker Lens Replacement side marker lens and housing for models. Note: Gaskets sold separately. K red ea Chrome Side Marker Bezel Correct chrome die-cast reproduction of the original front side marker bezel for use on Nova models front ea front ea rear ea medallion (lens and bezel sold separately) Custom Side Marker Medallions Laser cut from mirror polished stainless steel, each medallion mounts with double sided tape between the side marker lens and the bezel for a custom appearance. Medallions only. Two pair required per vehicle. Note: Bezel and lens not included pr Front Side Marker Lenses This is a correct reproduction for the front fenders. These side marker lamps include an amber lens assembly attached to the housing. Sold in pairs amber pr CP50029A CP50029D CP50029B CP50029E 3 LED Mini Clearance/Marker Light These 3 LED mini clearance/marker lights add a custom touch to your classic ride. Requires a 13/16" hole for installation. Note: Fabrication may be required for installation. CP50029A amber LEDs w/amber lens ea CP50029B red LEDs with red lens ea CP50029C amber LEDs with clear lens ea CP50029D red LEDs with clear lens ea CP50029E blue LEDs with clear lens ea CP50029F white LEDs with clear lens ea Side Marker Lamps. Bezels CP50029C CP50029F 219 Body Components H

15 Replacement Bulbs Bulb Kit for Emergency Use! Whether you re replacing your bulbs during a restoration or just want to be sure you re ready for any roadside emergencies that may come up, this handy kit takes all of the work out of searching around for the proper replacement miniature bulbs. It contains most every bulb you would need to replace all of your front parking lights, side markers, taillights, license lights, backup lights and turn signals. Gain peace of mind knowing that if you have a bulb go out while out on the road, you have plenty of spares to fit most any application. XX piece kit Turn Signal Indicator Dash Bulb Correct replacement bulb for the dash to indicate turn signals. Keep spare bulbs handy so your turn signals will always remain in good working order ea Side Marker Lamp Bulb Exact replacement bulbs for all Nova models. You choice of the front amber type bulb or the rear quarter panel bulb. Front 194A 1968 amber 1.99 ea clear ea Rear clear ea License Lamp Replacement Bulb B ea ea B ea ea ea LE194A LE11156A LE1157A LE3613W LE4414W SMD LED Light Bulbs Modernize the lighting equipment on your vehicle with these bright 6000k color temperature LED light bulb units. Manufactured to replace common bulbs on any vehicle with 12V capacity. LED bulbs not only react faster than traditional bulbs, but provide better light distribution. 194 Series Bulbs LE194W white pr LE194A amber pr LE194B blue pr LE194R red pr LE194G green pr 1156 Series Bulbs LE1156W white pr LE1156A amber pr 1157 Series Bulbs LE1157W white pr LE1157A amber pr LE1157R red pr Dome Lamp Bulbs LE3613W 3613 white pr LE4414W 4414 white pr Body Components H Rear Turn Signal Lamp Bulb Replacement bulb inserts in tail lamp assembly. The bulb indicates a LH or RH signal when the turn signal is activated ea Back-Up Lamp Replacement Bulb This bulb is for all back-up lamp assemblies ea Hood Lamp Replacement Bulb ea ea MX01106 MX01111 Ultra White Blue Bulbs Upgrade your lighting to Ultra White Blue Bulbs and enjoy a light that simulates daylight and reduces glare, fatigue and eye strain. Your vehicle will stand out in a crowd with the modern blue/white look of these bulbs. Available in a variety of bulb types and wattages to fit your specific needs. If you choose a bulb that is of a higher wattage than stock, we recommend installing our upgrade harness sold separately. Sold as a pair. 12 volt. MX01106 H4, 100/90W pr MX , 100W pr MX , 65W pr MX , 80W pr MX , 55W pr X Halogen/Xenon H4 Bulbs These Xenon gas filled bulbs are 50% brighter than halogen and offer a hyper white beam. They are a direct replacement for 5-3/4" or 7" headlights. Replacement Bulbs Halogen H /55w pr Xenon H X 60/55w pr X 100/80w pr /90w pr MX01200 MX01207 MX01213 MX01224 MX01220 MX01221 MX01222 MX01223 Colored Lamp Bulbs Have some fun, switch over to blue, green, red or purple bulbs for show use. Note: Using a bulb other than amber is not street legal, therefore, use colored bulbs for off-road or show use only. Tail/Stop Lamp 1157 XX201 clear pr MX01200 purple pr MX01201 amber pr MX01203 green pr MX01204 red ea Back-Up Lamp 1156 XX202 clear pr MX01209 purple pr MX01205 amber pr MX01207 green pr MX01208 red pr Instrument Lamp 194 XX203 clear pr MX01214 purple pr MX01211 blue pr MX01213 red pr License Plate Lamp 67 XX204 clear pr MX01224 purple pr MX01220 amber pr MX01221 blue pr MX01222 green pr MX01223 red pr 220 Replacement Bulbs Toll Free Order Line

16 Park Lamps A Park Lamp Assembly Reproduction park lamp assembly for 1962 Chevy II/ A26008 Nova models. Each park lamp includes the housing and lens LH ea RH ea Park Lamp Assembly Reproduction park lamp assembly for models. Each park lamp includes the housing, lens and wiring. Two required per vehicle. A LH ea A RH ea Park Lamp Assembly Reproduction park lamp assembly for models. Each park lamp includes the housing, lens and wiring. Two required per vehicle. A LH or RH ea Park Lamp Assembly Reproduction park lamp assembly for Chevy II/ Nova models. Each park lamp includes the housing and lens LH ea RH ea Park Lamp Assembly Reproduction amber park lamp assembly for Park Lamp Assembly Reproduction park lamp assembly for models. Nova models. Includes the housing, lens with original style Guide markings, socket with wiring pigtail and bulb. Fits LH or RH side, two required LH or RH ea Each park lamp includes the housing, lens and wiring. Two required per vehicle. A LH or RH ea A Park Lamp Assembly Reproduction park lamp assembly for 1965 models. Each park lamp includes the housing, lens and wiring. Two required per vehicle. A LH amber ea A RH amber ea 1970 Park Lamp Assembly Reproduction park lamp assembly for 1970 models. Each park lamp includes the housing, lens and wiring. Two required per vehicle. A LH or RH ea 1975 Nova Park Lamp Assembly OER reproduction park lamp assemblies for 1975 Nova models. The amber lens assembly is for standard Nova models and the clear lens assembly is for super sport and luxury models. Socket bulb and wiring not included. Fits LH or RH side two required per vehicle amber lens ea clear lens ea Body Components H Park Lamps 221

17 Park Lamps Body Components H Nova Rally Park Lamp Assembly Reproduction park lamp assembly for 1976 Nova SS and Nova Rally models equipped with diamond grill. Each park lamp assembly is reproduced in injection molded plastic to exact GM factory specifications with correct SAE and Guide markings for complete authenticity. Sold individually. 2 required per vehicle ea Park Lamp Assembly Manufactured by OER, these are officially licensed GM Restoration parts that install into the front grill area of 1976 and st design Nova models. Each lens features a painted white Bow Tie logo on the lens and correct stamped SAE, Guide and GM part number markings in the proper locations. Choose from the lens and housing assembly only or the full assembly which includes the lens, housing, bulb, socket with pigtail and hardware. Note: Not for use with Rally models. Lens and Housing Only LH ea RH ea Park Lamp Assembly Note: Not for use with Rally models. Socket wiring requires splicing into the factory wiring harness LH ea RH ea Park Lamp Assembly Manufactured by OER, these are officially licensed GM Restoration parts that install into the front grill area of nd design and 1978 Nova models. Each lens features a Bow Tie logo on the lens and correct stamped SAE, Guide and GM part number markings in the proper locations Choose from the lens and housing assembly only or the full assembly which includes the lens, housing, bulb, socket with pigtail and hardware. Note: Not for use with Rally models. Lens and Housing Only LH ea RH ea Park Lamp Assembly Note: Not for use with Rally models. Socket wiring requires splicing into the factory wiring harness LH ea RH ea 1962 Park Lamp Lenses Reproduction of the park lamp lenses for 1962 Chevy II/ Nova models. This reproduction features correct Guide markings as original. Sold in pairs. K pr Park Lamp Lenses Reproduction of the park lamp lenses for Chevy II/Nova models. This reproduction features correct Guide markings as original. Sold in pairs. K pr 1965 Park Lamp Lenses Reproduction of the park lamp lens for 1965 Chevy II/ Nova models. This reproduction is manufactured in the USA and features correct Guide markings as original. Sold in pairs. CMA pr Park Lamp Lenses Reproduction of the park lamp lens for Chevy II/ Nova models. This reproduction features correct Guide markings as original. Sold in pairs. K pr Park Lamp Lenses Reproduction of the park lamp lens for Chevy II/Nova models. This reproduction is manufactured in the USA and features correct Guide markings as original. Sold in pairs. CM pr 1970 Park Lamp Lenses Reproduction of the park lamp lens for 1970 Nova models. These reproductions are manufactured to factory specifications and feature correct Guide markings as original. Sold in pairs. CM3064A pr CM3064B 1970 Made in USA pr Park Lamp Lenses Reproduction of the park lamp lens for Nova models. This reproduction is manufactured in the USA and features correct Guide markings as original. Sold in pairs. CM Made in USA pr CM3061A pr Park Lamp Chrome Bezel Replace your dented and faded originals with these reproductions of the park lamp chrome bezels for Nova models. These bezels are manufactured to be just like original for a perfect fit. N required ea 222 Park Lamp Lenses. Bezels Toll Free Order Line

18 Park Lamps LED Park Lamps This is the latest in park lamp technology! These direct replacement LEDs for your factory park lamps exceed the requirements for brightness using very high intensity, wide angle LEDs. An exceptional way to increase visibility and add a cool aesthetic touch to your Nova! The LEDs are arranged to compliment the original lens facets and provide the best light output. Diffusion material is added for an even distribution of light and to help eliminate or minimize the spottiness that comes with LED lighting to give you a smoother, more natural look. Note: Lens and housing are not included set set set Park/Turn Signal Pigtail A molded plastic connector used to hold park/turn signal bulbs in their housing. The socket has lugs that lock into the lamp body and wiring to connect the bulb to the power source. Fits models. WE ea Park Lamp Lens Screws Correct replacement screw for models. Use two for each lens. C piece set set required ea K piece set set Park Lamp Bezel Moldings Reproduction of the park lamp bezels for models. Each bezel is manufactured in aluminum and designed to replace the original exactly. Sold in pairs. K LH and RH pr Park Lamp Wiring and Socket This reproduction socket is just what you need to get your Chevy II/Nova front lighting back in order. This wiring pigtail includes a correct socket park light socket ea Park Lamp Socket Boot This reproduction rubber park light socket boot helps to keep moisture and dirt out of your park lamp sockets. Correct for Chevy II/Nova models. N ea A11157 A Park/Turn Signal Pigtail A molded plastic connector used to hold park/turn signal bulbs in their housing. The socket has lugs that lock into the lamp body and wiring to connect the bulb to the power source. Fits models. A ea A ea Park Lamp Lens Gaskets Correct replacement gaskets for Chevy II/Nova models. Sold in pairs. W pr Park Lamp Lens Gaskets Correct replacement gaskets for Chevy II/Nova models. Sold in pairs. K pr Park Lamp Lens Gaskets Correct replacement gaskets for Chevy II/Nova models. Sold in pairs. W pr Park Lamp Lens Gaskets Correct replacement gaskets for Nova models. Sold in pairs. W pr Park Lamp Bezels Reproduction chrome park lamp bezels for models. Can also be used with 1962 models. K pr Vigilite Fiber Optic Lamp Bezel While most of today s vehicles have a lamp monitoring system, during the late 60 s and early 70 s Chevrolet offered this system as optional accessory. This system included a chrome bezel, which was attached to the top of each front fender. This chrome bezel housed a fiber optic cable with a lens that indicated whether or not your headlamps or turn signals were lit and operating properly. This ultra rare option was found on very few models. This is the outer chrome bezel assembly that was used with this system, which can be used on either fender. Note: The Vigilite system was also used on some other GM passenger cars, including Buicks and Olds. C ea Park Lamp/Turn Signal Bulb Replacement bulb for park lamp/turn signal assembly rear turn signal ea park lamp clear ea 1157A park lamp amber ea Park Lamps. Gaskets 223 Body Components H

19 Tail Lamps N Tail Lamp Assembly Reproduction tail lamp assembly for Chevy II/ Nova models except station wagon. This assembly includes: the bezel, back-up lens, tail lamp lens, gaskets, cross bracket and mounting screws. Pre-assembled and ready for installation. Two required per vehicle. Note: Not for station wagons ea K Tail Lamp Lenses Reproduction tail lamp lenses for models. The sets include: the red tail lamp lens, white backup lens and reflector lens. 2 sets are required per vehicle. Note: Will not fi t station wagon models. CMA with markings set K w/o markings set Tail Lamp Assembly OER reproduction tail lamp assembly for all Chevy II/Nova models. This assembly includes: the bezel, back-up lens, tail lamp lens, gaskets, cross bracket and mounting screws. Fits all models including station wagons. Assembly LH or RH ea Tail Lenses LH or RH ea required ea Tail Lamp Assembly Reproduction tail light assembly for Nova models. Each tail lamp assembly includes: the tail lamp lens, tail lamp bezel and gasket. Assembly N LH std model ea N RH std model ea Lenses LH std model ea RH std model ea Bezels LH std model ea RH std model ea Housings LH std model ea RH std model ea Body Components H N Tail Lamp Lenses Reproduction tail lamp lens for 1965 Chevy II/Nova models. These lenses have all of the correct Guide and SAE markings for an authentic appearance. A except wagon pr N station wagon pr 1965 Back-Up Lamp Lenses Reproduction back-up lens for 1965 Chevy II/ Nova models. Features correct markings. Not for station wagons. A except wagon pr Back-Up Lamp Lens Correct reproduction of the original back-up lenses for Chevy II and Nova models. Correct in every detail! K pair pr K Tail Lamp Assembly Reproduction tail lamp assembly for Chevy II/ Nova models. Each tail lamp assembly includes the correct lenses with Guide markings as original. Assemblies include the correct aluminum bezel and gasket. Assembly A LH ea A RH ea LH ea RH ea A LH ea A RH ea Lenses K pair pr N LH ea N RH ea LH ea RH ea Tail Lamp Reproduction tail light lenses, housings and gaskets for Nova models. The lenses feature the original Guide markings. Lenses LH ea RH ea Housings LH ea RH ea Gaskets pair pr W Tail Lamp Bezel to Body Gaskets Reproduction gaskets used to seal the tail lamp bezel to the body. W except wagon set W4155A 1965 except wagon set station wagon pr Tail Lamp Bezel to Body Gaskets Molded gaskets used to seal the tail lamp bezel to the body. These heavyweight reproductions will help prevent water or other elements from entering the trunk area pr pr pr N std models pr 224 Tail Lamps Toll Free Order Line

20 Tail Lamps Tail Lamp Filler Plate Gaskets This molded rubber seal attaches between the body and the filler plate that is below the tail lamps on all Nova station wagon models. Sold in pairs station wagon pr Tail Lamp Bulb Replacement tail lamp bulb for all Chevy II/ Nova models ea A11157 A11154 WE Stop, Tail and Turn Pigtail A molded plastic connector used to hold stop/tail/turn light bulbs in their housing. The socket has lugs that lock into the lamp body and wiring to connect the bulb to the power source. A ea A degree ea WE degree ea WE307 WE334 W Tail Lamp Lens Gaskets Replacement gaskets for Chevy II/Nova models. Each gasket inserts between the lens assembly and the bezel. Sold in pairs. W lens gaskets pr W lens gaskets exc. wgn 4.99 pr W lens gaskets pr W pr W pr W pr OER pr WE Back-Up Lamp Pigtail A molded plastic connector used to hold Halogen type bulbs in their backup lamp shell. The socket has lugs that lock into the lamp body and wiring to connect the bulb to the power source. WE ea WE ea WE ea Brake Light Relay When upgrading tail lights to the new higher wattage halogens, always use a relay. The Painless set gives you everything you need to protect your wiring and switches set The TattleTale Pulsing Brake Light Feel safer with the TattleTale pulsing brake light system! Designed to get attention, an inertia switch (which is adjustable by you, using supplied installation bracket) detects panic stop situations and re-routes the brake signal through an electronic pulsator. Under normal braking situations the brake lights react normally, but when hard braking occurs, the lights pulse rapidly, alerting other drivers of a panic stop. This system is great for 3rd brake lights and is for use with systems up to 60 watts (5 amps). Simple and easy-to-install. Includes installation instructions. T ea FB1055B FB1056P FB1056B FB1055N Billet Tail Lamp Assembly These billet tail lamp assemblies fit and Chevy II/Nova models. Bezels are machined from the finest quality 6061-T6 aluminum and feature high-quality lenses. Available in natural billet, polished or black anodized. Fits factory lamp location, comes with lenses, and LED upgrade. Note: You can not run these without the included LED upgrade. FB1055P polished aluminum pr FB1055B anodized black pr FB1055N natural aluminum pr FB1056P polished aluminum pr FB1056B anodized black pr FB1056N natural aluminum pr C LED Tail Lamp Lens Make a bold statement with this hot reproduction tail lamp lens and backup lens, both with LED circuit board to give your Chevy II/Nova an original but brighter look. The tail lamp lens comes equipped with super bright LEDs, and both feature fully sealed epoxy coated electronics. Note: Not for station wagon models. C tail lamp ea C back-up lamp ea tail lamp ea back-up lamp ea Arrows demonstrate the fl ow of light for the set, from the center of the vehicle or from the center of the lens. C Multi-Pattern LED Tail Lamp Panels Animate your tail lamps and make your Nova stand out! These LED panels feature a self-contained microprocessor and circuitry to enable multiple sequential lighting patterns. Make the light pattern flow at various speeds from the center of the vehicle outwards, from the center of the lens outwards, and more! Each set offers four different patterns. Made in USA. Important: The examples shown above are only two of the four patterns available on each panel set. All panels require a low current LED fl asher flowing patterns set flowing patterns set F LED flasher ea LED Tail Lamp Lens Assembly Make a bold statement with this hot reproduction tail lamp lens, with LED circuit board to give your Chevy II/Nova an original but brighter look. The tail lamp lens comes equipped with 36 super bright LEDs that are fully sealed with an epoxy coating. This lens eliminates the backup lamps. Two required per vehicle ea Body Components H Tail Lamps. Gaskets 225

21 LED Tail Lamp Conversion Dakota Digitaligital CL6037 example of a tail lamp lens example of a tail lamp lens LED Tail Lamp Conversion Make a bold statement with this hot LED tail lamp conversion for models. This conversion with special circuitry provides maximum brightness so your car will be safer and look better. These conversions will fit into your existing tail lamp housings and can use your existing wire harness for quick and easy installation. Tail lamp lenses and housings are not included and can be purchased separately if necessary. Note: This is the tail lamp circuit boards only. DD set example of a 1965 tail lamp lens Dakota Digitaligital CL6044 DD150 Dakota Digitaligital LED Tail Lamp Conversion Make a bold statement with this hot LED tail lamp conversion for models. This conversion with special circuitry provides maximum brightness so your car will be safer and look better. These conversions will fit into your existing tail lamp housings and allow you to use your existing wire harness for quick and easy installation. Tail lamp lenses and housings are not included and are available for purchase separately. Note: This is the tail lamp circuit boards only. DD set DD set Body Components H 1965 LED Tail Lamp Conversion Make a bold statement with this hot LED tail lamp conversion for 1965 models. This conversion with special circuitry provides maximum brightness so your car will be safer and look better. These conversions will fit into your existing tail lamp housings and can use your existing wire harness for quick and easy installation. Tail lamp lenses and housings are not included and can be purchased separately if necessary. Note: This is the tail lamp circuit boards only. DD set example of a tail lamp lens Dakota Digitaligital LED Tail Lamp Conversion Make a bold statement with this hot LED tail lamp conversion for models. This conversion with special circuitry provides maximum brightness so your car will be safer and look better. These conversions will fit into your existing tail lamp housings and can use your existing wire harness for quick and easy installation. Will work on Nova and Nova wagons. Tail lamp lenses and housings are not included and can be purchased separately if necessary. Note: This is the tail lamp circuit boards only. DD set Dakota Digitaligital LED Tail Lamp Conversion Make a bold statement with this hot LED tail lamp conversion for models. This conversion with special circuitry provides maximum brightness so your car will be safer and look better. These conversions will fit into your existing tail lamp housings and can use your existing wire harness for quick and easy installation. Tail lamp lenses and housings are not included and can be purchased separately if necessary. Note: This is the tail lamp circuit boards only. DD set Sequential LED Tail Lamps This is the latest in tail lamp technology! These LED replacements for your factory tail lamps fit perfectly behind your factory lens and bezel, and are far quicker responding and much brighter than DOT requirements! These sets use very high intensity, wide angle LEDs for an exceptional way to increase visibility and add an extra aesthetic touch to your Nova. They provide two modes of operation, standard or sequential. The sequential mode gives you a unique cascading affect that will really get you noticed! Changing modes is as easy as flipping a switch on the back of the circuit board. Every light circuit board is specifically designed to use the maximum area of the housing. The LEDs are arranged to compliment the original lens facets and provide the best light output. Diffusion material is added for an even distribution of light and to minimize the spottiness associated with LED lighting for a smoother, more natural look. These are to be spliced into the rear wire harness. Includes everything needed for a perfect installation. Each set will convert both LH and RH tail lamps. Tail lamp lenses and housings are not included and can be purchased separately if necessary. Note: This is the tail lamp circuit boards only set set 226 LED Tail Lamps Toll Free Order Line CM LED Tail Lamp Upgrade Update your Chevy II/Nova s tail lights with new LED technology. LEDs are far brighter than incandescent bulbs, light up in less than.05 seconds, use less energy and last much, much longer. Since they are brighter, illuminate instantly and are visible from farther away, LED tail lamps are not only a significant safety upgrade for your car, but also give your car a clean, modern look when the brake lamps are lit. These LED circuit boards are easy-to-install. Simply splice into the factory wire harness and the LED arrays fit neatly beneath the stock lens, providing a stock look when the tail lamps are off. Because this upgrade is invisible, it appeals to owners of both modified and restored cars. Each set includes: two LED arrays, electrical harnesses, connectors and all necessary brackets and mounting hardware. CL set CL set CM set example of a tail lamp lens example of a tail lamp lens

22 Important Information Before Attempting To Install Sheet Metal! Regarding Minor Imperfections in Panels: The sheet metal you receive may have scratches, dings, small dents and other minor imperfections which are considered normal sheet metal characteristics due to the nature of the product. These minor imperfections will be easily corrected during the filling, priming and sanding phase of your sheet metal installation. Classic Industries does not consider dings, scratches, minor dents or other imperfections on the sheet metal to be defects in the panel nor are they considered damaged. All sheet metal panels will require some sort of preparation and manipulation during installation. Every panel that we sell is inspected and then carefully packaged to protect against damage that may occur during transit. Test Fit All Panels Prior to Paint and Installation: Classic Industries recommends test fitting all sheet metal panels prior to final paint and installation. Minor modifications including elongating mounting holes, adding additional shims, etc. are normal and may be necessary when installing sheet metal. It is important to note that hard driving conditions, like racing, can twist bodies and frames out of original tolerances. Poor body work from previous collisions can cause problems with the body structure that the panels are attached to. Some vehicles were manufactured with a unitized body (no frame) thus causing even the most minor accident to twist the body creating a situation that would cause sheet metal panel misalignments. Take into consideration that tolerances on classic vehicles are not nearly as exact as they are on modern vehicles. This is primarily due to the hand fitting of panels at the factory on most antique and classic cars as opposed to the robotics used in today s modern factories. All of these factors will affect the way your new reproduction sheet metal will install and fit on the car. There is really no such thing as a direct fit body panel when it comes to older vehicles. Returns and Defects: Prior to returning any defective body panel or sheet metal item to Classic Industries, please contact our customer service department. Classic Industries will not replace a panel, nor will we be responsible for freight on returns should it be deemed that the panel is not defective. See policies for more information. For Best Results, Hire a Professional to Install the Panels: Classic Industries recommends that you hire a professional paint and body technician that has the skills, knowledge and experience necessary to install the new panels on your vehicle. A professional body technician will be able to prepare the panels for installation and repair any imperfections. When Welding Sheet Metal Products... Save time when replacing sheet metal by using Classic Industries new, innovative Weld-Thru TM primed sheet metal products. Our all new coating process is designed to eliminate the unnecessary process of grinding or sanding the EDP coating off to ensure a solid and rust free weld. This Weld-Thru TM primer requires minimal preparation and eliminates corrosion problems between overlapped panels and layered spot welds. It also minimizes heat zone problems, reduces panel distortion, and allows better penetration into the dense replacement steel to compensate for the older metal s impurities. Look for the Weld-Thru TM logo when purchasing sheet metal products to save time during installation of weld-on sheet metal repair panels. Some Guidelines on EDP Coating Many sheet metal products are delivered with a black electrophoretically deposited coating (EDP, or E-coat) for superior long-term corrosion protection, while others use a similar lacquer-based coating designed to provide protection for storage and shipping. Before panel installation, Classic Industries recommends applying lacquer thinner with a shop towel to determine the type of coating. If the coating is removed by lacquer thinner, then it should be completely stripped from the product before any primer or paint is applied. If the lacquer thinner does not remove the EDP coating, it can simply be prepped, primed and painted without stripping. Classic Industries The Restorer s Choice Count on the Classic Industries Restorer s Choice TM symbol whenever purchasing reproduction parts and accessories. You can be sure that each and every product displaying this symbol is manufactured correctly to exact specifications and fits the way the factory intended. Products denoted throughout the catalog with this symbol are officially approved by Classic Industries as a genuine restoration product. Look for the Restorer s Choice TM logo. The Classic Industries symbol is your assurance of quality. Made in USA Look for the Made in USA logo for products that are proudly manufactured in the United States. Sheet Metal Information 227 Body Components H

23 Reproduction Hoods Steel Hood All steel reproduction of the hood for Chevy II/Nova models. Each hood is manufactured to exact factory specifications for an authentic appearance and fit. Finished in EDP coating for rust protection. Ready to prep and paint! ea " Cowl Induction Steel Hood Installs and fits exactly like original except features a 2" raised cowl section. The hood offers the appearance of an early muscle style hood. Each hood is nonfunctional but looks great! Finished in EDP coating for rust protection. Ready to prep and paint! C " rise ea N " rise ea " Cowl Induction Steel Hood Installs and fits exactly like original and features a raised cowl section. The hood offers the appearance of an early muscle style hood. Each hood is nonfunctional but looks great! Finished in EDP coating for rust protection. Ready to prep and paint! C " rise ea Standard Steel Hood All steel reproduction Chevy II/Nova hood. Each hood is manufactured to exact factory specifications for an authentic appearance and fit. Finished in black primer coating for rust protection. Ready for prep and paint! ea " Cowl Induction Steel Hood Reproduction cowl induction style hood for Chevy II/Nova models with a 4" rise for a custom, high-performance look. Each hood is produced using highquality, EDP coated steel and made to original specifications. Features correct under hood bracing and is ready to prep, paint and install C " rise ea Body Components H Steel Hood All steel reproduction hood for Chevy II/Nova models. Manufactured in stamped steel to factory specifications for an authentic fit and appearance and is EDP coated to prevent rust. Features correct underhood bracing and comes ready to prep, paint and install. Will install with factory or reproduction hinges and latch ea " Cowl Induction Steel Hood Installs and fits exactly like original and features a raised cowl section. The hood offers the appearance of an early muscle style hood. Each hood is nonfunctional but looks great! Finished in EDP coating for rust protection. Ready to prep and paint! C " rise ea 228 Steel Hoods Toll Free Order Line

24 Composite Hoods Harwood Pro-Touring Fiberglass Hood Give your Nova the Pro-Touring F13100 look with this fine fiberglass hood from Harwood. This Pro-Touring hood has a 2-1/2" bump and features a fully finished underside and includes a custom trim bezel for the air inlet. The air inlet comes closed from the factory but can be cut open for a functional ram air effect. The hood utilizes the factory hinges and latches. B bolt-on type ea N14660 F Fiberglass Hood Fiberglass replacement hoods for Chevy II/Nova models. Lightweight and sturdy in construction. Important: *Low tension hood springs are required for this hood. F stock hood (hood pin style) ea N14660 * stinger hood (bolt on style) ea F stock hood (hood pin style) ea F stock hood with cowl panel (hood pin style) ea Standard Carbon Fiber Hood Molded using an original factory hood, this carbon fiber hood looks great on any pro-touring or custom build. Available in a variety of materials and in satin or gloss finishes to suit any taste or budget. Hood pins recommended. C68078CG Gloss Finish C68077FG C.F. with fiberglass understructure ea C68077CG % carbon fiber ea C68077DG % dry carbon ea C68078FG C.F. with fiberglass understructure ea C68078CG % carbon fiber ea C68078DG % dry carbon ea Satin Finish C68077FS C.F. with fiberglass understructure ea C68077CS % carbon fiber ea C68077SG % dry carbon ea C68078FS C.F. with fiberglass understructure ea C68078CS % carbon fiber ea C68078SG % dry carbon ea B Cowl Induction Fiberglass Hood These fiberglass cowl induction hoods from Hardwood Industries will either meet or exceed your expectations for looks, clearance, or weight restrictions. Available in pin-on or bolt-on variations. Bolt-on hoods require part number B210 medium tension springs not the low tension springs. Important: *F14105 hood has a cowl panel integrated into the hood. Deletes factory cowl panel and windshield wipers. Hood Pin Style F " cowl induction ea F " cowl induction ea F " cowl induction ea F " cowl induction ea F " cowl induction ea F " cowl induction ea F14105 * " cowl induction with integrated cowl panel ea F " cowl induction ea Bolt-on Style B " cowl induction ea B " cowl induction ea B " cowl induction ea B " cowl induction ea Carbon Fiber Cowl Induction Hood Lighten your load and add some pro-touring style with this carbon fiber cowl induction style hood. Designed as a direct bolt-on, this hood will install as original and deliver great looks as part of any pro touring or custom build. Available in a variety of materials and satin or gloss finishes to suit any taste or budget. Hood pins recommended. C68079CG Gloss Finish C68079FG carb fib with fiberglass under structure ea C68079CG % carbon fiber ea C68079DG % dry carbon ea Satin Finish C68079FS carb fib with fiberglass under structure ea C68079CS % carbon fiber ea C68079SG % dry carbon ea Cowl Induction Hood Screen This is a really cool idea for cowl induction hoods. You can now cover the opening in the back of the hood on your non-functional cowl hood with this made in the USA stamped steel screen. This screen can be chromed, powder coated or painted to match your vehicle s color. Installs easily without removing the hood. Includes mounting screws ea Body Components H Composite hoods 229

25 Fiberglass Hood Scoops HA1103 HA1107 HA1111 HA1112 HA1114 HA1116 HA1124 HA1126 HA1128 Body Components H HA4103 HA4104 Harwood Fiberglass Cowl Hood Scoop These hood scoops are designed to provide extra clearance underhood and reduce weight while providing a highperformance look. Available in a flanged style that can be bonded or riveted on, and also a limited selection of bolt-on styles. Note: Shipped oversize. *Shipped double oversize. Part # Style Length Width Height Notes Price HA1103 flange 43" x 28" x 2.5" trim to length for desired fit ea HA1107 flange 43" x 28" x 4" trim to length for desired fit ea HA1111 flange 53" x 28" x 2" trim to length for desired fit ea HA1112 flange 54" x 28" x 3.5" trim to length for desired fit ea HA1114 flange 53.5" x 31" x 4" trim to length for desired fit ea HA1116 flange 49" x 28" x 6" trim to length for desired fit ea HA1124 flange 53.5" x 28" x 4" smooth top - trim to length for desired fit ea HA1126 * flange 57" x 28" x 6" smooth top - trim to length for desired fit ea HA1128 flange 54" x 28" x 8" smooth top - trim to length for desired fit ea HA4103 * bolt-on 43" x 29.5" x 2.5" rivet-on ea HA4104 bolt-on 43" x 29.5" x 4" rivet-on ea HA1117 flange 53.5" x 27" x 7.5 flange ea HA hood Scoops Toll Free Order Line

26 Fiberglass Hood Scoops HA3164 HA4162 HA3161 HA3165 HA4163 HA3166 HA3182 HA4164 HA3163 HA3168 HA3183 HA4166 HA1999 HA2000 HA2001 HA1996 Harwood Fiberglass Aero Hood Scoop These hood scoops are designed to provide maximum air flow and a lightweight advantage while providing a look that will fit in with the sleekest of all-out performance machines. Available in a flanged style that can be bonded or riveted on, and also a limited selection of bolt-on styles. A selection of scoop plugs are also available. Note: Larger scoops are shipped oversize. Part # Type Style L W H OAL Notes Use Plug # Price HA3161 Aero Pro I flange 36" x 17" x 11" 48" open back HA ea HA3163 Aero Mini II flange 30" x 15" x 7" 31.5" closed back HA ea HA3164 Aero II flange 29" x 17" x 9.5" 35" closed back HA ea HA3165 Aero Mod I flange 43" x 17.5" x 8.5" 48" closed back HA ea HA3166 Aero III flange 29" x 17" x 7.5" 35" closed back HA ea HA3168 Aero Pro III flange 37" x 20" x 11" 48" open back HA ea HA3182 Tri Aero flange 40" x 14" x 13" 51" open back HA ea HA3183 Tri Aero Mini flange 30" x 14" x 11" 33.5" closed back HA ea HA4162 Aero Mini I bolt-on 30" x 14.5" x 9" 32" incl gskt & hdwr HA ea HA4163 Aero Mini II bolt-on 30" x 15" x 7" 31.5" incl gskt & hdwr HA ea HA4164 Aero II bolt-on 29" x 17" x 9.5" 35" incl gskt & hdwr HA ea HA4166 Aero III bolt-on 29" x 17" x 7.5" 35" incl gskt & hdwr HA ea HA1996 scoop plug use with HA3182, HA ea HA1999 scoop plug use with HA ea HA2000 scoop plug use with HA3160, HA3161, HA3164, HA3165, HA3166, HA4164, HA ea HA2001 scoop plug use with HA3162, HA3163, HA4162, HA ea Body Components H Hood Scoops 231

27 Hood Accessories Fiberglass Hood Scoop Give your hood a touch of high-performance styling inspired by the scoops found on the famous Camaro IROC-Z for a sleek performance look. Manufactured in fiberglass rather than ABS plastic. This scoop measures: 50-1/2" long, 24-3/4" wide and 3" tall. PT ea Universal L-88 Style Hood Scoop Give your car some high-performance styling with this universal fit L-88 style hood scoop. Patterned after the famed L-88 hood originally found on Corvettes with the L-88 engine, this scoop is manufactured in high grade fiberglass rather than ABS plastic. This scoop measures: 45-1/2" long, 26" wide and is 3-1/2" tall. PT ea louver with bezel detail Super Sport Hood Louvers OER reproduction hood louvers for Nova Super Sport models. Each cast hood louver is painted black and features bright chrome accents with necessary mounting hardware and chrome bezels included. Purchase the kit and save or just the individual components needed for your restoration. Hood Louver Kit K kit Individual Components hood louvers pr louver bezels LH or RH ea louver gaskets 2 required ea Hood Louver Bracket This top quality reproduction is a must when restoring your Nova Super Sport back to its original condition. This stamped steel bracket mounts the SS hood louvers to the underside of your hood. Sold in pairs SS pr K Hood Hinge Springs Add a custom touch to your hood hinges with these brightly polished stainless steel hinge springs for models. Each spring is manufactured to fit and function like the original unit, while giving your underhood area the finishing touch. Manufactured to operate original or reproduction steel hoods only pr pr pr pr Body Components H Universal Hood Scoop Add a subtle performance look by adding this cowl style hood scoop to the hood of your car. This universal style hood scoop is manufactured in fiberglass for added durability. Measures: 31-1/2" long, 26" wide and 1-3/4" tall. Note: Shipped oversize. PT ea K Hood Louver Gaskets These gaskets are designed to prevent moisture from being trapped under the hood louver, potentially causing deterioration of the paint surface or the metal hood surface beneath the louver. Choose the original style adhesive backed sponge foam in roll form or replacement style molded gasket. K molded gasket pair pr OER strip gasket 2 required ea Hood Springs Never have to use a prop rod on your trick looking fiberglass hood again. These low tension springs will allow you to retain the original workings of your hood. For cowl induction hood B200 low tension pr B210 med tension pr Hood Hinge Springs Replace your old worn out springs with these reproductions ea ea ea AK120B Hood Hinge Bolts Original HEX head style bolts available in polished chrome or polished stainless steel. For use on all Chevrolet hood hinges. Set of 8. AK120A chrome set AK120B stainless set Hinge Bolts Reproduction stainless steel hood hinge bolts for Nova models. Black oxide or plain stainless finish. Black Oxide Coated set set Plain Stainless Steel set set 232 Hood Accessories Toll Free Order Line

28 Hood Accessories Billet Nova Hood Hinges Replace your original stamped steel hood hinges with these beautiful billet aluminum hinges with gas struts. No modifications needed for installation bolts right in! Hinges are made from the finest quality T6 aluminum and use weatherproof bearings and stainless steel hardware to ensure proper operation in any climate. Hinges come with black carbon steel struts and all required mounting hardware. Available in polished, black anodized or natural finish. Polished FB1051PF FB1052PF FB1053PF Black FB1051BF FB1052BF FB1053BF Natural FB1051NF FB1052NF FB1053NF Polished FB1051PS FB1052PS FB1053PS Black FB1051BS FB1052BS FB1053BS Natural FB1051NS FB1052NS FB1053NS FB1052NF Fiberglass Hood FB1051BS set set set set set set set set set Steel Hood set set set set set set set set set Hood Hinge Original factory replacement or our superb quality reproduction hood hinges! Reproductions are manufactured from OE materials using new tooling. Hood hinge spring not included. Important: The hinges for 1962 and nd design used an 18 coil spring, and are currently not available. Note: *For use with 27 coil spring 1st and 3rd design * LH ea * RH ea LH GM ea RH GM ea LH reproduction ea RH reproduction ea LH reproduction ea RH reproduction ea CB60112 natural black gray CB Ringbrothers Billet Hood Hinges CNC-machined from solid 6061-T6 billet aluminum, these hinges are a direct replacement piece with no modifications necessary and feature ball bearing pivot joints and gas shocks either as a solid frame hinge or the new high tech air frame. Installation hardware and instructions included. Available in natural, black or gray anodized aluminum finishes and for steel or fiberglass hoods. Solid Arm Style Natural Aluminum CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Anodized Black CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Anodized Gray CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Air Frame Style Natural Aluminum CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Anodized Black CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Anodized Gray CB steel hood pr CB fiberglass hood pr CB steel hood pr CB fiberglass hood pr Replacement Hood Shocks Black Only Billet Hinge Shocks - Steel Hood CB pr Billet Hinge Shocks - Fiberglass Hood CB pr Hood Release Cable Premium hood release comes complete with a machined billet aluminum handle assembly and cables. The cables are HR1100 cut-to-fit, designed with a specially extruded liner for extended life of the cable, aluminum fittings and stainless steel inner wire. These hood release cables include aluminum firewall fittings and cable stop. The outer housing is 18" inside the vehicle and 6' under the hood. The inner wire is 9' long. Available in a black or stainless steel housing with a beautiful billet cutout handle. Important: Requires cable operated latch. HR1100 stainless steel housing ea HR1100B black housing ea B Adjustable Hood Prop Constructed of high-quality aluminum and stainless steel, these adjustable hood props offer great looks as well as functionality on your ride. When the hood is raised, the hood prop will automatically lock itself into position. A quick release allows the hood to be opened to its max for easy engine access. A three position and a six position option allows the hood to be set at various levels. Each level of the six position prop increases the opening of the hood by approximately 6". Each level of the three level prop increases the opening of the hood by approximately 12". They also works great for cooling your engine in the staging lanes position aluminum ea position aluminum ea B 3 position black ea B 6 position black ea Hood Lamp to Hood Bumper Reproduction rubber bumper. For Chevy II models. This bumper was installed as the underhood lamp to hood bumper ea K Hood Rubber Bumpers The rubber stoppers on your hood can become worn out, deteriorated, or simply lost. These reproduction stoppers will help your hoods appearance as well as provide a secure fit when closing the hood hood bumpers (round) pr side bumpers (4) set K side bumpers (2) pr K hood side panel ea A /8" front bumpers 4.99 ea FB1057A Stainless Steel Hood Adjuster Custom replacement billet stainless steel hood adjusters come with rubber bumpers and are sold individually. Available in 1/4"-20, 5/16"-18 and 7/16"-14. FB1057A 1/4" ea FB1057B 5/16" ea FB1057C 7/16" ea Hood Accessories 233 Body Components H

29 Hood Accessories Hood Latch Assembly Reproduction hood latch assembly for Chevy II/Nova models. These latch assemblies are manufactured to exact factory specifications to ensure perfect fit and function ea ea Hood Latch Pilot Bolt Reproduction hood latch pilot bolt for Chevy II/Nova. Will replace the original pilot bolt as shown. The hood latch pop-up spring surrounds this bolt ea Hood Pop-Up Spring Reproduction hood pop-up spring for Chevy II/Nova. Available in black /4" ea CB40046 CB40047 Billet Hood Pins Machined from 6061-T6 billet aluminum, these hood pins feature a base that screws into core support for easy installation and includes stainless steel locking pin for secure closure. Installation hardware and instructions included. Sold in pairs, available in natural, black and gray finish. CB40046 natural pr CB40047 black pr Body Components H A Billet Hood Safety Latch Direct replacement billet hood safety latch assemblies made from a solid piece of 6061-T6 aluminum and 304 stainless steel. Hood latch comes with a billet aluminum base plate, pilot bolt and retaining cup and pop-up spring (some applications). Stainless steel fasteners and billet aluminum finishing washers also included. Offered in black, polished or satin finishes Nova A black ea A polished ea A satin ea Nova A black ea A polished ea A satin ea Nova A black ea A polished ea A satin ea Hood Safety Latch Reproduction hood safety A Hood Safety Latch Reproduction hood safety latch for Nova models. Manufactured to factory specifications for proper fitment and function. Comes EDP coated for rust prevention ea ea latch for Nova models. This bracket and pilot bolt are mounted to the underside of the hood and act as a guide for the latch mechanism ea Stainless Hood Latch Pilot Bolt Add a custom touch to your hood latch with this brightly polished stainless steel pilot bolt for Nova models. Each bolt is manufactured to fit and function like the original unit, while giving your under hood area the finishing touch. Made in USA ea Billet Hood Latch Bolt This hood latch bolt is machined from stainless steel and dresses up an often forgotten area of your engine bay. Includes nut and washer, but does not include hood latch or spring. D set Stainless Pilot Bolt Add a custom touch to your hood latch with this brightly polished stainless steel pilot bolt for models. Each assembly is manufactured to fit and function like the original unit, while giving your underhood area the finishing touch. Made in USA ea Hood Latch Catch Support The hood latch catch support is located between the grill and radiator support. The hood latch assembly bolts to the upper portion of the support and is stabilized by the support. This support also helps to strengthen the entire front section of the vehicle. This roughly triangular part duplicates the original exactly, both aesthetically and functionally. Produced in correct gauge metal and comes finished in black. Note: * support also fi ts, installs and functions on 1968 models but differs in appearance from original equipment ea ea * ea Flip Over Style Hood Pin Set Each set uses two piece flip over pins which flip over stud and lock into place. Over center action eliminates possibility of pin falling out. Includes lanyards. This set is a reproduction of the rare, dealer installed optional hood pins. Hood pins are necessary for the attachment of fiberglass or lift off hoods and may be installed for extra security on factory hoods. Note: Though intended for use on models, it may however be used on all years. T set Universal Simulated Hood Pins Get the look of billet hood pins without having to drill holes in your expensive hood. Machined billet plate from 6061-T6 aircraft aluminum, stainless steel pins, screws and cables. Installs in minutes with no tools, just peel and stick. Available in classic or striker design. 24" cables sold separately. Note: These are non-functioning hood pins. Hood Pins 25109P classic polished set 25109B classic black set 25110P striker polished set 25110B striker black set Cables Only 25113R 24" long red pr 25113B 24" long black pr 25113C 24" long clear (silver) pr 234 Hood accessories Toll Free Order Line P HP B Hotchkis Custom Hood Pins These Hotchkis custom universal hood pins add a high tech aerospace look to your car. They offer lightweight durable construction, easy installation, secure hood closure and killer good looks. H1760 universal set polished gloss black chrome plated Billet Aluminum Hood Pin Set These U.S. made, 6061-T6 aluminum hood pin and scuff plate sets will help your car stand out in a crowd and complement any style hood. The billet scuff plates are available in your choice of machined, polished, or powder coated black finish. All hood pin sets include 6" aluminum pins and stainless steel hardware, so you ll never have to worry about rust. HP5001 machined finish set HP5002 polished finish set HP5003 gloss black powder coated set HP5005 chrome-plated set

30 Hood Accessories Underhood Lamp Under hood lamp for Nova models. Reproductions are manufactured to factory specifications including correct color wiring and terminal ends. NV ea K Hood Insulation Reproduction hood insulation for Chevy II/ Nova hoods. Each hood insulation is manufactured in a heat resistant material which will help to extend the life span of the paint on your hood and helps dissipate heat from your engine compartment. Note: This is a glue on style insulator. Clips not required. K set K set K set STEP 1 Hood Damper Pads/Heat Shield Custom Underhood/Trunk Mirrors Make a statement and beautify your engine and trunk compartments with these awesome looking custom cut mirror sets. These mirrors are made of 1/8" thick lightweight and heat resistant plastic that are professionally designed to fit perfectly to your factory hood and trunk lid. Mirror sets can be purchased for under the hood only, under the trunk lid only, or in a money saving hood and trunk set. All mirror sets include silicone, caulking gun, masking tape, 4 oz. cleaner, towel and instructions. Hood Mirrors set set set set set Trunk Mirrors set set set set set Complete Mirror Sets set set set set set Jute Padding Insulation This insulation is just what you need to completely insulate the interior of your vehicle against cold or heat. Developed from 99.5% pure industrial grade aluminum, the insulation gives 97% reflectivity against heat radiation. Jute padding will insulate your interior for noise while helping to maintain an even temperature. Use on firewalls, floor pans, trunks, doors, and roof panels or other areas of the vehicle. CMD1003 4' x 2" x 6' ea Hood Insulation Retainer Reproduction hood insulation retainers are just what your Nova needs! Keep your original hood insulation where it belongs... attached to the hood. These retainers are service replacements for most models. They may differ cosmetically from the original retainer but will fit and function properly. Sold Individually. Use as required. A ea DM11905 DM11102 Dynamat Universal Hood Insulation Dynamat hoodliners will protect your car s paint and reduce irritating underhood noise. Made from 3/4" acoustic sound soaker foam with a reinforced, aluminized skin that is oil and water resistant. The hoodliner has a high tack pressure sensitive adhesive for easy peel and stick application. For those who prefer black, there is also Dynaliner, which boasts the highest heat blocking properties available in a single layer synthetic foam. Dynaliner is available in 1/4" and 1/2" thick. Use the thickest one your space will allow. All hood insulation sheets measure 32" x 54". Hoodliner DM /4" ea Dynaliner DM /4" ea DM /2" ea 01 SS 396 STEP 2 High Temp ABS Finishing Panel Logo Design Options 02 SS SS Nova Script 05 Nova Script w/ss 06 Bow Tie w/chevy II Quiet Ride AcoustiHOOD Insulator & Cover Kit Pre-cut, ready-to-install insulation panels, and cover! AcoustiHOOD insulator and cover kits by Quiet Ride are designed to help stop the vibration of the hood skin, thus reducing the transfer of air-born noise into the passenger cabin by 20-25%, or 3 decibels. It also covers the hood structure with a high temperature ABS panel to finish off the engine bay. These panels will regularly tolerate temperatures up to 250 F. Important: Does not fi t cowl hoods. For best results & air fl ow, maintain at least one inch or more of clearance between the surface of the hood cover and the engine components. Hood not included and is available separately.kit also includes a drill stop sleeve & drilling instructions in case drilling is required. Quiet Ride Solutions attempts to use existing hood pad mounting holes. Drilling may be required if never equipped. For non metallic hoods (such as fi berglass or carbon fi ber), hood magnets will be used to retain the hood cover, and will need to be glued into place. Note: Please specify 2 digit logo code when ordering. Shipped double oversize and ground only (no air shipments) due to aerosol spray adhesive. A specify logo kit A without logo kit A specify logo kit A without logo kit A specify logo kit A without logo kit A specify kit A without logo kit Body Components H Hood accessories 235

31 Reproduction Fenders Nova Fender Reproduction fenders are an excellent way of replacing your rusted or damaged factory originals. Each reproduction fender will install correctly and is manufactured to original specifications. The fenders are finished in a semi-flat black EDP coated finish completely ready to paint to your desired color LH ea RH ea A Nova Fender Reproduction fenders for Chevy II/Nova models. Available in your choice of our Restorer s Choice TM panel, Officially Licensed by GM, manufactured in OE gauge steel featuring all original contours and details or our standard replacement for the car builder on a budget. Fenders come finished in semi-flat black EDP coating to prevent rust and are ready to prep and paint to your desired color. Restorer s Choice TM B LH ea B RH ea B LH ea B RH ea Standard Replacement A LH ea A RH ea A LH ea A RH ea 1966 Nova Fender The fenders are finished in a semi-flat black primer and are ready to paint to your desired color. Quality reproduction fenders are just what your Chevy II/Nova needs for a true, original appearance. If you re going to replace your fenders, you ll want to be sure the quality is 1st rate LH ea RH ea Inner Fender Panel HS325 Now you can install new inner fender panels to complete your Nova subframe installation. They are stamped so that they will bolt directly to the fenders, core support and frame rails, and include hood hinge mounting plates, firewall seals, and hardware. They can also can be used where a Mustang II IFS suspension has been installed on stock frame rails. Note: Shipped oversize. HS pr HS pr Body Components H 1967 Nova Fender Each reproduction fender will install as original and is produced with high grade factory gauge steel. The fenders are finished in a semi-flat black primer and are ready to paint to your desired color. Quality reproduction fenders are just what your Chevy II/Nova needs for a true, original appearance. If you re going to replace your fenders, you ll want to be sure the quality is 1st rate LH ea RH ea Inner Front Fender Panel Reproduction inner front fender panels with lower frame rails. Features provisions for the upper and lower suspension arms, shock tower mounts and hood hinges. These panels also feature holes stamped in the correct locations for mounting the fender and mounting various engine compartment items. Panels are EDP coated for rust prevention and have all the correct ribbing and reinforcements as original. Important: For factory type front suspension only LH ea RH ea 236 Fenders Toll Free Order Line

32 Fender Components PDN97L PDN97R N Inner Fender Well Each fender well is manufactured with OEM thickness steel just like original. Each panel will fit and install correctly allowing the rusted or damaged panel to be replaced. These reproductions also include an EDP coating that helps eliminate rust and allows the panel to be installed immediately. N LH ea N RH ea Fender Apron Reproduction passenger side fender apron for all Chevy II/Nova models. This panel installs on the front side of the inner fender panel and acts as the mounting point for the battery tray. Comes EDP coated for rust prevention RH ea PDN100L PDN100R Fender Patch Panel A correctly stamped front fender patch panel which installs on the rear lower fender area. Each panel will replace the rear lower section of this commonly rusted rear area without replacing the entire fender Models PDN97L LH 13" H x 18" L ea PDN97R RH 13" H x 18" L ea Models LH 11-1/2" H x 15-1/2" L ea RH 11-1/2" H x 15-1/2" L ea Models PDN100L LH 13-1/2" H x 16" L ea PDN100R RH 13-1/2" H x 16" L ea Front Fender Ornament Reproduction fender ornament for Nova models with Exterior Decor Package (ZJ5). Fits LH or RH fender. C required ea C2363 C Fender Skirt to Firewall Brace Reproduction skirt braces that mounts to the rear inner side fender, dash panel bracket and the firewall brace. C LH ea C RH ea 14713W 14712W C69541L C69541R D Front Frame Inner Fenders Detroit Speed s Chevy II inner fenders are designed to fit Chevy II models equipped with a DSE Chevy II Front Frame. They completely hide the front frame downbars resulting in a neat and clean underhood appearance. The inner fenders are stamped from 18 gauge steel and are made in the USA. D pr D pr Lower Fender Extension Braces The fender extensions require special stamped steel braces to connect the extensions to the fenders. Some applications include mounting bolts for fast installation. Sold in pairs without hardware pr includes hardware pr stainless w/o hdware pr includes hardware pr Outer Cowl Side Panel Replace your rusted or damaged cowl side panels with these quality reproductions. These panels are installed behind the fenders at the sides of the firewall. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated ea RH EDP coated ea 14713W LH Weld-Thru TM ea 14712W RH Weld-Thru TM ea C69541L LH uncoated ea C69541R RH uncoated ea Body Components H Fender Components 237

33 Body Panels Fiberglass Front End This fiberglass front end assembly is designed to fit 1966 and 1967 Chevy II/Nova models. Includes: the front fenders, grill, headlamp section, lower front valance and bumper assembly. This form of construction completes a solid belly pan look and offers extreme rigidity. Perfect for strip or show. Important: Although originally designed for a 1967 model, the front end will also fi t a 1966 Nova and 1967 models featured different grill and headlamp styles. This item does not include the hood panel (sold separately). Not intended for street use. F front end less hood ea C Upper Inner Cowl Panel Reproduction of the upper inner cowl panel for Nova models. Features factory style contours, pre-punched holes, correctly made openings and mounting points for the windshield wiper motor. With AC EDP coated ea Without AC C11020A EDP coated ea C uncoated Made in USA ea Fiberglass Front End This fiberglass front end assembly is designed to fit 1968 through 1972 Chevy II/Nova models. This front end (less hood) includes front fenders, grill, headlamp section, lower front valance and bumper assembly. This form of construction completes a solid belly pan look and offers extreme rigidity. Perfect for strip or show. Although originally designed for a model, the front end will also fit a 1973 or 74 Nova models featured different grill and headlamp styles. Important: This does not include the hood panel (sold separately). Not intended for street use. F front end less hood ea Cowl Top Vent Grill Panel Reproduction cowl top vent grill panel for Nova models. Manufactured to factory specifications featuring correct contours, original style mounting points and EDP coated for rust prevention ea ea C Vent Delete Carbon Fiber Cowl Panel Take some weight off your front end with this bolt-on panel. This panel installs behind the hood at the base of the windshield. The cowl vents and recesses have been filled for smooth look. Available in your choice of satin or glossy finish. Either choice offers both a great look and significant weight reduction. Note: Shipped oversize. C gloss finish ea C68080S satin finish ea Body Components H Front End Doghouse Assembly Reproduction of the commonly rusted front end assembly for Nova models. Manufactured to factory specifications this assembly features correct contours, and includes the radiator support, inner fenders, shock towers and all factory bracing. Comes coated in Weld-Thru TM primer. Special order ea Inner Cowl Panel Reproduction inner cowl panel for all Nova models. Manufactured from heavy steel gauge, features correct contours and is EDP coated for rust prevention ea 238 Body Panels Toll Free Order Line

34 Body Panels 16101W Lower Cowl Panel Reproduction lower cowl panel for Chevy II/Nova. This panel is welded-in below the cowl top vent grill panel. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Cowl Panel EDP coated ea 16101W Weld-Thru TM ea Cowl Shoulder Panel LH Weld-Thru TM ea RH Weld-Thru TM ea 16104W Coupe Inner Roof Panel Braces If you re replacing your entire roof of your Nova coupe, you ll need this set of reinforcements to complete the job correctly. Stamped from correct gauge steel and designed to fit and install as original. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated set 16104W Weld-Thru TM set 53-3/4" W Front Pillar Drip Rail Support These supports are essential when installing a roof panel because they reinforce the front pillar section of the roof. Installs on the front pillar section of the roof panel and extends downward vertically between the roof panel and fender. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated ea RH EDP coated ea 16107W LH Weld-Thru TM ea 16108W RH Weld-Thru TM ea " Chevy II/Nova Roof Panel Coupe Roof Panel Rear Drip Rail Supports Exact reproduction pillar drip rail supports. Installs on the rear pillar section of the roof panel and extends down vertically between the roof panel and trunk. These components are crucial when installing a roof panel because they provide critical support to the rear pillar section. Sold in pairs. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated pr TM 16106W Weld-Thru pr underside view Replace the dented, rusted or otherwise damaged original roof panel on your Chevy II/Nova hardtop with this stamped reproduction. Each panel is manufactured to exact factory specifications. Important: Roof drip rail and window molding channel not included ea Roof Panel Reproduction roof panel for Nova models. Manufactured to factory specifications from new steel tooling, featuring original style contours, correct gauge sheet metal and EDP coated for rust prevention ea 16106W Plugweld Pliers These plugweld pliers make plug welding fast and easy. The unique copper alloy backing plate will not stick to welds! Unique design allows you to clamp panels at a precise spot and still allow for welding. Panels won t separate and weld will not stick to the copper pad. Copper alloy pad prevents burn through, allows higher welding temperature and better penetration. S ea S23231 replacement copper swivel pad ea S20017 S20015 S20016 Seam Buster These heavy-duty chisels allow you to easily separate spot welded or bonded panels. Save up to 15 minutes per panel replacement. Great for quarter panels, rocker panels and other pinch welded areas. Sharpened on two edges, the sharp end allows for penetration between panels and the side edge allows for side impact to drive the panels apart without damage. Made of super tough alloy steel. Cushioned handle absorbs shock. S20015 straight ea S degree angle ea S20017 for use with air hammers ea Body Panels 239 Body Components H

35 Vinyl Tops & Body Panels Nova/Chevy II Vinyl Top Reproduction vinyl tops for Chevy II/Nova models are manufactured using the finest quality Levant grain vinyls for the ultimate in originality. The seams are sewn with dacron bonded thread and then dielectrically heat sealed as original for a truly authentic appearance. There are two types of seams were used for certain years; 1) Heatsealed seams which are stitched seams then folded over (stitching is not exposed) 2) French stitched seams which are double stitched on the top (stitched seams are exposed). French seams go down the center of the roof and the heat sealed seams go along the sides. Replacing your original vinyl top will make your Nova look showroom new once again. Classic Industries recommends professional installation for best results. Important: Each vinyl top is pre-cut for the rear window and pillar post areas. All models used moldings to fi nish the lower rear edge of the vinyl top and will need to be cut and trimmed to fi t the specifi c vinyl top moldings for each year. Be sure to check the design and placement of the moldings before trimming and gluing the top to ensure accuracy. Note: Tops are full tops, must be trimmed to fi t for vehicles with half tops. Can be used on hatchback models B Nova Concourse 1966 Nova black white dark green buckskin 1969 Nova 2 Door Hardtop XB black two heat sealed seams ea XB white two heat sealed seams ea XB dark green two heat sealed seams ea XB buckskin two heat sealed seams ea N black two heat sealed seams ea N white two heat sealed seams ea XB dark green two heat sealed seams ea XB buckskin two heat sealed seams ea 2 Door and 4 Door Sedans Including Concourse and Hatchbacks XB black two heat sealed seams ea XB white two heat sealed seams ea XB dark green two heat sealed seams ea XB buckskin two heat sealed seams ea N black two heat sealed seams ea N white two heat sealed seams ea N dark green two heat sealed seams ea N buckskin two heat sealed seams ea N black French center seam ea N white French center seam ea N buckskin French center seam ea Door Shell When replacing the outer sheet metal panel alone on your Chevy II/Nova isn t enough, these reproduction door shells are just what you need. Window regulator, handles, hardware, latches, etc., are not included and must be purchased separately or transferred over from the original door. Hardtop LH ea RH ea B LH ea B RH ea B LH ea B RH ea 2 Door Sedan LH ea RH ea LH ea RH ea Body Components H mounts on the lower sail panel Vinyl Top Moldings A top quality reproduction of the vinyl top moldings used on Nova that featured a vinyl covered roof. This is a four piece set of moldings that run from the bottom edge of the quarter window to the bottom edge of the rear window. They are used to finish off the edge of the vinyl top set Outer Door Skin These replacement steel door panels will enable you to replace your damaged or rusted out door skin with a long lasting durable replacement. Each panel has been reproduced to exact specifications and will fit the door frame perfectly LH 2 door coupe ea RH 2 door coupe ea 240 Vinyl Tops. Body Panels Toll Free Order Line

36 Body Panels L 2 door Outer Door Skin These replacement steel door panels will enable you to replace your damaged or rusted out door skin with a long lasting durable replacement. Each panel has been reproduced to exact specifications and will fit the door frame perfectly LH 2 door coupe ea RH 2 door coupe ea L Outer Rocker Panel Reproduction outer rocker panel skin designed to replace the rusted or damaged original. Available for 2 or 4 door models. These are outer sections only. Note: *Shipped oversize L LH 2 dr 49-1/2"L ea R RH 2 dr 49-1/2"L ea L * LH 4 dr ea R * RH 4 dr ea 4 door Outer Rocker Panel Reproduction of the outer rocker panels fit directly below the door area and between the wheel wells. Note: Shipped double oversize S78002L LH 2 door ea S78002R RH 2 door ea S78004L LH 4 door ea S78004R RH 4 door ea Outer Door Skin These replacement steel door panels will enable you to replace your damaged or rusted out door skin with a long lasting durable replacement. Each panel has been reproduced to exact specifications and will fit the door frame perfectly LH 2 door ea RH 2 door ea F Fiberglass Door These fiberglass door shells will enable you to replace your damaged or rusted door with long lasting durable fiberglass replacements. OEM style hinge and latch mounting pads are reinforced and accept OEM hardware for easy installation. The full inner panel must be trimmed out to gain access inside the door. Available for 2 door models. For use with lexan window and hardware only (not included). Note: * shipped oversize. ** panels require truck freight delivery. F13010 * LH ea F13011 * RH ea F14010 ** LH ea F14011 ** RH ea R Lower Outer Door Skin Patch Panel Replace the rusted out lower section of the outer door skin with this 7" high patch panel. Eliminates the need to replace the entire panel. For Nova only L LH ea R RH ea Full Outer Rocker Panel These OE style full outer rocker panels will replace rusted or damaged original panels on your Chevy II/Nova LH 2 door ea RH 2 door ea N14662W Complete Rocker Panel Replace the rusted out rocker panels with these reproduction rocker panels for Chevy II/ Nova models. These include the inner and outer portions. Measures 77" in length. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. N LH EDP coated ea N RH EDP coated ea N14661W LH Weld-Thru TM ea N14662W RH Weld-Thru TM ea Inner Rocker Panel Reproduction inner rocker panels for Nova models. Mounts behind the outer rocker to form the complete rocker panel LH ea RH ea Inner Rocker Panel Stamped steel reproduction inner rocker panels for Nova models. Installs under the doors behind the outer rocker panel and between the wheel wells. Includes the lower kick panel area as shown LH ea RH ea Rear Rocker Panel Flaps Replace the often missing or disintegrating rear rocker panel flaps on your Nova with these high-quality reproductions. These flaps prevent road splash and debris from entering the car and blocking the rocker panel drain area. Each flap mounts on the rear side of the inner rocker panel. KW pr K7926 K Rocker Reinforcement Panel Replace the commonly rusted rocker reinforcement panel on your Nova with this quality reproduction. This panel mounts between the inner rocker panel and the front wheel well near the kick panel area. For hardtop models or convertibles. K LH ea K RH ea Quickly Remove And/Or Install Vehicle Doors! EZ Rest Door Hanger The EZ Rest Door Hanger enables a single person to quickly remove and/or install vehicle doors. The padded, removable side rails and plastic, ribbed base inserts allow for accurate positioning of the door. The easy on/off design quickly adapts to most floor jacks with a removable saddle and 30mm (1.18") diameter saddle hole. Note: Floor jack is not included. S ea Body Components H Body Panels 241

37 Body Panel Hardware X9858 Cleco Sheet Metal Fastener Set This Cleco sheet metal fastener set contains everything you need to secure sheet metal panels during the fit and alignment stage. The pliers can be used with all standard spring loaded fasteners and clamps. The complete kit contains: one pair of Cleco pliers, twenty-five 1/8" Kwik-Lok clecos and four side grip fastener clamps. Also available are individual components so you can add to your kit as necessary. X9858 complete 29 piece kit kit X9859 individual clecos 1/8" ea X9860 individual clecos 3/16" ea X9862 side grip fastener clmps 3/4" x 1" 4.99 ea X9863 cleco pliers ea Glass Fiber Rust Remover Before touching up paint, you first must remove all rust, wax, and dirt or the rust will return and the paint won t adhere. This unique tool will scrub away all dirt, rust and wax. The results are touch up paint adheres, seals and blends smoothly into the rest of the paint. E ea F Front End Alignment Shim Reproduction front end alignment shims for Nova models. Unlike generic shims, these offer an original appearance. With the proper shims, you can adjust your front end and not lose judging points at a car show. We offer two sizes and most vehicles use a total of six shims: four 1/8" and two 1/16". However, this is only a guideline as some cars use more shims than others. Sold individually. Use as needed. F /16" ea F /8" ea N Front End Fastener Hardware Set Includes all the correct fasteners used in assembling the entire front end sheet metal. This set replaces rusted, incorrect or missing pieces. Includes: washer head point cap screws, plastic clip nuts, etc. This set is a must if you are replacing your front end sheet metal. The original hardware will probably need to be replaced. Take advantage of this set for everything you need! Note: Does not include grill installation hardware. N set N set Vise Grip Flange Pliers Preparing panels with an offset flange will produce a clean, flush fit. Work on up to 18 gauge sheet metal without removing panels from the car. The added feature of Vise-Grip locking pliers allows for better leverage. Available with your choice of 1/2" wide non-slip jaw or wider 1" clamping surface /2" wide jaw ea X9853 1" wide jaw ea J-Nut Assembly Reproduction J-nut that was used for the installation of many products on the front end of various GM models from Sold individually or in a money saving kit of /16"-18 thread ea K piece kit kit Front End 5/16" Pointed Indented Head Bolts Correct black oxide bolts used for mounting radiator supports, fender to radiator support braces and hood latch support assemblies. The bolts are 5/16". K set Body Components H Pull Rod Set If you don t have to replace expensive sheet metal, why do it! Repair your damaged metal with this easy to use set. This set includes: 4 pull rods with formed shank, 2 pick pulls with straight shank, straight edge, and HS split point drill bit. S set X /16"-18 Hex Head Bolt Reproduction of the hex washer head bolts that were used for the installation of many products on the front end of various GM models from Sold individually or in a money saving kit of 10. Individual /4" length ea /16" length ea X /4" length ea Kit of 10 K1551 3/4" length kit K /16" length kit K /4" length kit FK Underhood and Trunk Fastener Set If you are looking for a bolt set for under the hood and the trunk area then this is it! The only complete set available for your Nova. Includes: fender bolts and U-nuts, hood hinge bolts, wheel well bolts and U-nuts, radiator bolts, trunk lid bolts, hood latch, horn bolts, motor grounding screw, AC heater housing screws, master cylinder nuts, tail light nuts, windshield washer bottle, grill screws and nuts and more! FK piece set FK piece set 242 Body Panel Hardware Toll Free Order Line

38 Body Panel Hardware The Benefi ts of Stainless Steel With an Original Look! SK Exterior Screw Set Replace the essential screws and fasteners necessary for the grill, headlight bezels, outer mirrors, parking lamp lens and bezels, quarter panel moldings, tail light lens and windshield moldings. Each set contains the correct amount of screws needed to replace the essential items found on the outer body. Sets vary from year to year on screw count and only include those screws that are visible from the outside. SK piece set SK piece set SK piece set SK piece Chevy II set SK piece set SK piece set SK piece set SK piece set SK piece set Body Dent Remover Pulls dented sheet metal back into place. Drill a hole in the deepest part of the dent and insert hook or selfthreading screw tips. Tap lightly with the 2-1/2 lb slide hammer to remove dent. 13" long shaft permits high pulling force. Slide hammer has 1/2"-13 UNC thread. Caution: Wear safety glasses. X set X hook and screw package ea X nose nut ea Double-End Spotweld Cutter Double-end spotweld cutters makes removing body panels fast and easy. Their hollow design cuts around the spotweld so weld hardness does not affect tool sharpness. When one end becomes dull, simply unscrew the cutter and flip it over using the new teeth on the other end. An adjustable depth rod sets the tool so only the outer panel is cut, leaving the underlying panel undamaged. Arbor with Cutter ea Replacement Cutters piece set Replacement Arbor ea Replacement Pilot piece set Door Aligning Bar Finally, a convenient door aligning tool that will fit in your tool drawer! Features a hex stub to use with a breaker bar and socket for additional leverage. S ea Body Bolt Set Tired of endless searching for the correct fasteners? Growing weary of buffing, sanding and painting rusty old fasteners? Put an end to all of that with our complete stainless steel fastener sets. These sets contain individually packaged and labeled stainless steel component sets to eliminate any guesswork in assembling your restoration project. Our original style indented hex body sets come with black stainless where appropriate to retain a factory original appearance while giving you the rust free benefits of stainless steel Body Bolt Set Sets for models contain the fasteners you need to assemble your bumpers, door hinges, door latch, door jambs, front and inner fenders, hood hinges, hood latch, hood catch, hood stops, radiator support, crossmember, shock towers, battery box, trunk hinges, trunk latch, trunk catch, tail lamps, master cylinder, windshield washer tank, interior trim screws and more set Body Bolt Set Sets for models contain the fasteners you need to assemble your bumpers, door hinges, door latch, door jambs, front and inner fenders, hood hinges, hood latch, hood catch, hood stops, radiator support, front seat mount, master cylinder, shock towers, battery box, trunk hinges, tail lamps, master cylinder, interior trim screws and more set Body Bolt Set Sets for models contain the fasteners you need to assemble your bumpers, door hinges, door jambs, front and inner fenders, hood hinges, hood latches, hood catch, radiator support, battery box, horn, front seat mount, trunk hinges, trunk latch, trunk catch, license plate and bracket, gas tank, interior trim and more! set Body Bolt Set Sets for models contain the fasteners you need to assemble your bumpers, door latches, front fenders, grill, headlamp bezels, hood hinges, hood latch, hood catch, radiator support, battery box, master cylinder, seat mounts, trunk hinges, trunk latch, trunk catch, interior trim screws and more! set T2300M (7 piece) soft med. heavy T2302 Soft Duty Delicate prying or wedging Med. Duty Sturdy prying or wedging Heavy-Duty Very strong and durable Prying and Scraping Tools Available in 3 different fiberglass reinforced plastics, the soft duty tools are good for jobs where a minimum amount of force is needed to remove objects. The medium duty tools are better for the objects that require a little more force to remove, and the heavy-duty tools are for the objects that are real stubborn and just do not want to be separated from their current position. All these tools are strong enough to pry yet soft enough to do interior and exterior automotive jobs without the damage that metal tools can do. 7 Piece Prying and Wedging Tools T2300S soft duty set T2300M medium duty set T2300H heavy-duty set 4 Piece Scraper Tools T2301S soft duty set T2301M medium duty set T2301H heavy-duty set Metric Gap Gauge T mm ea Fastener Set These are the only fastener sets available for your Nova. They include fasteners for: back-up lamps, battery tray, bumpers, bumper brackets, bumper guards, bumper filler panel, cowl panel, door latches, fenders, fender braces, fender splash shields, fender extensions, grill, grill brackets, grill moldings, headlamp adjusters, headlamp bezels, headlamp housings, header panel, hood, hood hinges, hood catch and lock plate, hood catch support, hood moldings, license plate brackets, marker lamps, nameplates, parking lamps, tail lamps, trunk latch and striker, trunk lid, valance panel, wheelhouses, wheelhouse brackets, all related spring nuts and more! N items set N items set N items set N items set N items set N items set N items set N items set Body Components H Body Panel Hardware 243

39 Door Hinges & Hardware (sold individually) Upper Door Hinge Reproduction door hinge designed and manufactured for the ChevyII/Nova. Each hinge will fit exactly as original. Each hinge includes four bolt holes for installation as original LH or RH ea LH ea RH ea Door Alignment Wedges The door alignment wedges are necessary to help keep the doors from sagging due to fatigue in the door frame structure which could cause damage to the weatherstrips and body. The door mounted wedge will contact with the door frame wedge to maintain proper alignment. CM set K hardtop set K Door Hinge Bolt Set Reproduction bolt sets are for 2 upper or 2 lower door hinges including both door side and body side bolts upper or lower set K upper set K lower set Door Hinge Replacement Pin Correct replacement door hinge pin to repair broken hinges without the high cost of replacing the entire hinge. A front upper ea G front upper & lower 2.99 ea A door ea Door Hinge Bushing Correct replacement bushings for Chevy II/ Nova models smooth o.d ea A splined o.d ea G9682 A Door Hinge Bolt These replacement bolts are the correct length and are identical to the original in size and grade. Upper/Lower Hinge to Body A /16"-18 x 1" (3/8"o.d.).99 ea Upper Hinge to Body and Door G /16"-18 x 1-1/4" ea Body Components H Lower Door Hinge High quality reproduction door hinges for Chevy II/Nova. Each hinge is ready to bolt on LH ea RH ea LH ea RH ea Door Spring Tool Compresses spring for easy safe removal. Slides safely over spring. Constructed of heat treated, high carbon steel. Great for all GM models. S ea Lower Door Hinge Roller Detent These detent roller repair sets are an economical and simple repair alternative to expensive replacements. Instructions included. K LH and RH set Door Hinge Repair Set Repair broken door hinges with this unique set that contains 4 proper hardened shouldered pivot pins and 8 bronze bushings. Will repair all 4 upper and lower hinges. K set HC241 HC241A Lower Door Hinge Arm Replace this often worn out or broken arm on the lower door hinge. The detent roller rides on cutout notches on the steel arm. The door hinge detent spring also attaches into this arm. 1 required per hinge. Attachment rivet sold separately HC door hinge arm ea HC241A rivet ea Door Hinge Adjuster Tool You can now easily adjust the hinges without the aggravation of trying to align by eyesight with this handy tool. Specifically designed to help adjust the hinges so they help to align the door. Y ea 244 Door Hinges. Hinge Repair Kits Toll Free Order Line

40 Door Latches & Hardware Chevy II/Nova Door Latch Assembly OER reproduction of the door latch assembly for Chevy II/Nova models! Replacing the latch can help the door to operate smoothly and correctly the way the factory intended LH ea RH ea LH 2 door ea RH 2 door ea LH ea RH ea Door Latch Screw Set Door latch screw set for Chevy II/Nova models. Fits and functions as original. CX /4"-20 x 3/8" set Door Relay Mechanism Reproduction door relay mechanism for 1967 models. Each relay will replace the original exactly LH ea RH ea Firewall Relay Cover Reproduction rubber firewall relay cover for Chevy II/Nova models. This cover was originally equipped on convertibles and models equipped with power accessories. F ea Door Lock Striker Plates Reproduction door striker plates for Chevy II/Nova models. Worn striker plates can interfere with the correct operation of our door. Fits front and rear doors for 2 and 4 door models pr Stainless Steel Door Lock Strikers These are a custom stainless steel versions of the door lock strikers that mount in the door jamb area of the quarter panel. These billet striker bolts are 7/16" x 14 and will fit most GM applications MD stainless steel pr MD polished pr CB44102 MD Billet Door Strikers These custom billet aluminum and stainless steel door lock strikers mount in the door jamb area of the quarter panel and keep the door securely closed. Each striker plate is machined from 6061-T6 billet aluminum and features a striker turned from 304 stainless steel for durability. 7/16"-14 thread pitch, 1" thread length, 1-1/4" striker length. Sold in pairs. Available in natural, black or gray finishes. CB natural pr CB black pr Door Striker Bolt Washer Reproduction door striker bolt washer manufactured in die-stamped steel and finished in clear zinc coating. Used to correctly position the door striker bolt for proper alignment with the door latch assembly. Use as required. Note: * Pt # threads on. The other 3 slide on mm thick ea mm thick ea * 3.50mm thick (threaded) ea mm thick ea Door Striker Washers Reproduction of the door striker washers for models. These are the correct plastic washers installed behind the striker to allow you to adjust the striker without marring the paint. Sold in pairs. F pr Power Window Relay Replace your inoperative power window relay and bring your factory power windows back to working order. These are reproduction power window relays used by GM on most models equipped with optional power windows. 30 amp pwr window ea pwr tailgate ea pwr windows/locks ea CX Window Switch Assembly Refresh your interior by replacing your peeling or inoperative window switch with an original GM or reproduction switch. Choose from a one button switch that mounted on the passenger or rear doors, 2 button switch which mounted on the driver door or a 4 button switch that operated all windows. Note: Reproduction style window switches may differ cosmetically, but will fi t and function as original. The one button style switch will work on the passenger side but must be modifi ed by trimming back the length on the pin. 1 Button reproduction ea reproduction ea G GM ea 2 Button CX repro. LH ea repro. LH ea 4 Button reprod. LH ea Rear Window Switch Retainer Clip Correct clip which holds the window switch to the door panel use as needed ea Body Components H Door Latch. Window Switches 245

41 Door Lock/Window Motors CL1127 CL Door Lock Pawl Reproduction lever that mounts at the end of the door lock cylinder allowing the door latch assembly to be activated when the key is turned. CL LH ea CL RH ea CL LH ea CL RH ea 1968 Inner Door Lock Rod Reproduction of the inner door lock rod for 1968 Chevy II/ Nova models. This rod attaches to the door latch and is used to unlock the door from the inside. This is the upper vertical rod threaded at one end where the door lock knob screws onto. For use on the driver or passenger door. Sold individually. 2 required ea Front Window Guide Reproduction front window guide for Chevy II/ Nova models. N front ea Door Window Roller OER reproduction front door window roller for Nova models. C ea W Power Window Motor These remanufactured power window motors have been reengineered for a better than new performance. Each motor is remanufactured and then sealed with a higher than OE quality gasket to protect the motor from the elements. Each unit is supplied without the window lift gear. We recommend replacing the gear with our W300 gear sold separately. Power Window Motors without Gear W LH front ea W RH front ea W LH rear ea W RH rear ea W LH ea W RH ea Window Lift Gear W LH or RH ea G Door Inside Locking Rod Clip This clip is used to hold the door lock knob rod assembly to the lower rod assembly which pivots up and down when the door lock knob is raised or lowered. Clip used to hold the inner locking rod to the inner door frame panel. This clip will help to eliminate rattling which occurs from a damaged or missing clip. G ea ea K Door Bumpers Replace worn out door bumpers with these correct reproductions door requires 2 each upper and lower bumpers piece set K piece set upper 4 required 1.99 ea Door Push Button Lock Spring Reproduction door handle push button lock spring for all Nova models. Designed to meet OE specifications exactly LH ea RH ea Body Components H Door Latch Rod Clip 2 piece door latch rod retaining clip set. These clips secure the door release rod to the inner door skin piece pr Door Lock Rod Retaining Clip Reproduction of the clip that retains the two inner door lock rods. This nylon clip joins the horizontal rod from the door latch with the vertical rod that the door lock knob screws on to. Sold individually. One required per door. Fits into a 17/64" hole and secures a 5/32" rod. K ea C Lower Window Track This is a reproduction of the lower frame portion of the front door where the door glass installs. The door window glass rests on this lower window track. Available for LH or RH door. C LH 2 door ea C RH 2 door ea Window Guide Roller Nut Tool This OER manufactured tool is designed to easily remove the guide plate nut on door or quarter window glass. Fits most models T ea Door Lock Cylinder Retainer If you re replacing your door lock cylinder it may be necessary to replace the retainer. This retainer holds the lock cylinder in the correct position ea Outer Door Lock Cylinder Gasket Correct replacement door lock gasket for Chevy II/Nova models. This gasket prevents your lock cylinder from making contact with the paint. We recommend replacing your original gaskets when replacing your locks. Sold individually. Use as required. K ea 246 Door Lock. Window Motors Toll Free Order Line

42 Door Components R5050 R Outer Door Handle Push Button This set includes the LH and RH door handle push button assemblies. These high polished chrome buttons include: the chrome thumb knob, attachment rods, tension springs, o-ring gaskets and button retainers for easier installation. Note: On some models the push button retainer fl ange may require minor trimming in order to fi t correctly on the inner retainer at the back of the outer door handle. This was due to minor variances between GM divisional suppliers. Outer Door Handle R set R set R set Door Handle Push Button 0-Ring ea CB70001 CB70002 CB Outer Door Handles 2 Door Handle to Body Gaskets Door Handle Set Replace your original pitted or worn-out outer door handles with these sets. Includes the necessary components to replace your outer door handles, door handle gaskets and o-rings. Give your restoration the look it deserves with this comprehensive set! Each handle is manufactured to exact factory specifications and includes highly polished triple chrome-plating for a dazzling appearance. R or 4 door front set CM door rear only set R or 4 door front set CM door rear only set R5001B door set CM door front only set CM door rear only set G Outer Chrome Door Handle Replace your outer door handles with these original GM replacements. Each handle is chrome-plated as original and will fit your door exactly the way the factory intended! These factory original outer handles will fit all Chevy II/Nova models. Door Handle G RH ea Door Handle Gaskets K with lock cylinder gaskets set R without lock cylinder gaskets set R5001B Ringbrothers Billet Door Handles Add some stylistic flair to your exterior door handles with a pair of high tech billet 2 Push Buttons 2 Push Button O-Rings door handles. CNC-machined from solid 6061-T6 billet aluminum. Installation hardware and instructions included. Available as one or two piece handles in various colors. Two piece handles are available fully polished or two tone polished inner with removable matte outer. Note: The downward angle/mounting area of the handles differ between models. Slight modifi cation may be necessary. Two Piece Door Handles CB polished/polished pr CB polished/matte pr CB black//matte black pr GSE2100A GSE2100B Lokar 12V Exterior Door Handles Elevate your car s style with these electronic exterior door handles from Lokar! Each billet door handle utilizes a weatherproof 12 volt pressure pad switch to supply power to an electronically actuated door latch (door popper). Its two piece design and available 0 degree or 10 degree mounting surface allows the insert to be removed, and door handle positioned for ultimate customization. The XL design provides 7/8" of clearance between the door and the switch, allowing for easier mounting and less modifications to the door. Made in the USA from 6061-T6 billet aluminum. Important: Requires electronic door latch actuators, not included. Note: *Installation requires hand pocket for clearance. GSE2100A* brushed pr GSE2100B* polished pr GSE2101A* brushed 10 degree pr GSE2101B* polished 10 degree pr GSE2102A brushed XL pr GSE2102B polished XL pr GSE2103A brushed 10 degree XL pr GSE2103B polished 10 degree XL pr Body Components H Door Handle Components 247

43 Lock Cylinders & Components TK157 TK135 Body Components H TK112A TK109A Lock Cylinder Sets Ignition Locks Replace your ignition lock cylinder with a correct replacement available with original style or reproduction late model keys for X-Body models. TK octagon key ea TK original key ea TK octagon key ea TK158A 1965 original key ea TK late model key ea TK100A original key ea TK late model key ea TK101A 1968 original key ea TK late model key ea TK late model key ea Door Locks Includes: both LH and RH door lock cylinders and 2 keys. Replace your original lock assemblies with these reproductions. Each lock cylinder is coded to the keys that are provided with the kit. TK late model key pr TK109B original key pr TK109A original key pr TK Ignition and Door Lock Sets Includes: ignition cylinder lock and 2 door lock cylinders with 2 keys. All of the locks in this set are coded to work with the same pre-cut key. TK late model key set TK142A octagon key set TK143A 1965 original key set TK late model key set TK104A original key set TK late model key set TK105A 1968 original key set TK late model key set Trunk Locks Includes: correct coded trunk lock cylinder assembly with 2 pre-cut matching keys. Eliminates the need to take your original keys to a locksmith for coding. TK112A original key ea TK late model key ea TK112B 1968 original key ea Door Lock Cylinder Original service replacement cylinders for Nova models. These cylinders are uncoded and must be taken to a locksmith with your original key and coded to your existing key. G ea Trunk Lock Cylinder Kit Each cylinder is uncoded so that your original key can be used. Simply have a locksmith code the cylinder to your existing key. G wagon, electric ea G uncoded ea Trunk Lock Gasket Replace your original lock cylinder gaskets with high-quality K941 reproductions. Helps eliminate water from entering the trunk area as well as preventing the lock cylinder assembly from damaging the paint. K ea K ea Trunk Lock Retainer Replace this often lost or broken item with a quality reproduction. Trunk lock retainers are now available for Chevy II/ N3120 Nova models. N ea N ea N ea 248 Door Components Toll Free Order Line TK266 TK Door and Trunk Lock Sets Includes: correct replacement for doors and trunk lock. Includes cylinder assemblies and 2 keys. All of the locks in this kit are coded to work with the same pre-cut key. Comes in a complete set so you can change your door and trunk locks and have one key for both. TK late model key set TK135A original key set TK late model key set Ignition, Door & Trunk Lock Complete set designed to replace your ignition, door and trunk lock assemblies. Each set is supplied with coded cylinders and 2 pre-cut keys which will fit the new door, ignition and trunk lock cylinders. TK original key set TK original key set TK original key set Ignition, Door, Glove Box & Trunk Complete set designed to replace your ignition, door, glove box and trunk lock assemblies. Each set is supplied with coded cylinders and 2 pre-cut keys which will fit the new door, ignition, glove box and trunk lock cylinders. TK original key set TK original key set TK original key set TK original key set TK original key set Door, Glove Box & Trunk This set includes the correct replacement lock assemblies for the glove box, trunk and doors. Replace your original lock cylinders with a matched set! This set provides the coded lock assemblies along with 2 pre-cut keys to bring your locks back to original condition. TK late model key set TK170A original key set TK late model key set TK128A original key set TK155A 1968 original key set TK late model key set Glove Box & Trunk Lock Sets Includes: glove box lock cylinder and trunk lock cylinder with 2 pre-cut keys. All of the locks in this set are coded to work with the same pre-cut key. TK164A original key set TK late model key set TK121A original key set TK late model key set TK late model key set G Trunk Lock Handle Shaft Correct replacement of the trunk lock cylinder to latch torque rod. This rod extends from the outer trunk lock cylinder to the inner latch assembly and allows the lock to engage when the key is turned. CL ea Key Cover Each slip-on plastic key cover is produced to the exact configuration of the GM square or oval keys Available in black only square key cover 1.79 ea oval key cover ea

44 Door Components Briggs and Stratton Style Key We offer these original Briggs and Stratton type GM keys which are not pre-cut and may be purchased for the indicated years listed. Simply take these keys and your original keys to a locksmith or key shop, present your old key and have a new key cut to fit K109 K111 your lock cylinder. K ignition A ea K trunk B ea K ignition A ea K trunk B ea K ignition C ea K trunk D ea Original GM Replacement Key We offer these original GM keys which are not pre-cut and may be purchased for the indicated years listed. Simply take these keys and your original keys to G4604 G4605 a locksmith or key shop, present your old key and have a new key cut-to-fit your lock cylinder. G ignition late style ea G ignition late style ea G ignition late style ea G trunk late style ea G ignition late style ea G trunk late style ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea G ignition ea G trunk ea KK Keyless Entry System Do-it-yourself keyless entry set designed specifically to fit your Nova. Sets include: a Keyless Entry module with onboard relays, two 2-button remotes, two 15 lb door lock actuators with integrated overload protection, necessary wiring and mounting hardware. Full color, step-by-step installation instruction manual. Note: Trunk release may require some minor trimming on some vehicles for installation. KK keyless door set KK keyless door & trunk set PDL5170 SDH103 Shaved Door Handle Sets Sets to shave your door handles and trunk lock (where applicable). Shaved door handle sets are available with emergency entry or an alarm. Important: Door handle plates and trunk block off plates (where applicable) not included. Shaved Door Handle Sets SDH100 without emergency entry set SDH101 with emergency entry set SDH102 with alarm set Shaved Door and Trunk Handle Set with Alarm SDH103 with alarm set Power Door Lock Conversion Sets These combination sets will convert your old manual locks to power and activate them from up to 100 feet away! Each set includes: two 4 button keyless remotes, two 15 lb door lock actuators, wiring harness and mounting hardware. Sets with trunk lock conversions also include trunk lock actuator. Sets with alarm include alarm system. Power Door Lock Conversion Set PDL set Power Door and Trunk Lock Conversion Set PDL set Power Door and Trunk Lock Set with Alarm PDL set Remote Door Openers Give your car a sleek, custom look by eliminating the door handles and the door and trunk locks. Available in your choice of either a 2 way or 3 way system. The 2 way system features two door actuators, two door latches and one 2 way remote transmitter. The 3 way remote system features two door actuators, two door latches, one trunk actuator, one trunk latch and one 3 way remote transmitter. Both sets come with all necessary connections and instructions. Additional transmitters also available way two doors set way two doors and trunk set Chevy II/Nova Window Regulator Reproduction window regulators for Chevy II/ Nova models. Manufactured as original for a correct fit and function. Front Regulator LH 2 door front ea RH 2 door front ea LH 2 door front ea RH 2 door front ea LH 2 door front ea RH 2 door front ea LH 2 door front ea RH 4 door front ea Rear Regulator LH 2 dr quarter ea RH 2 dr quarter ea LH 2 dr quarter ea RH 2 dr quarter ea LH 2 dr quarter ea RH 2 dr quarter ea LH 4 dr rr door ea RH 4 dr rr door ea NWK Power Window Sets Power window regulator sets for Chevy II/ Nova models. Sets include: motors, regulators, and hardware for installation. A universal switch and harness set is required to complete the installation. NWK front ht and conv set NWK front ht and conv set NWK front 2 door set NWK rear 2 door set Switch/Harness Sets One 2 Button Switch, One 1 Button Switch & Harness SWK set One 4 Button Switch, Three 1 Button Switches & Harness SWK set Door Components SWK Window Regulator Guide Cam Spacer Correct reproduction of the window regulator guide cam spacer for all Nova models. Sold individually. Use as required door ea all ea 249 Body Components H

45 Outer Door Mirrors OEM Ribbed Style Base! Available with or without Bow Tie emblem engraved on the back of the mirror as shown above. Features Bow Tie emblem engraved on the back of the mirror as shown above Ribbed Style Outer Door Mirror These mirrors feature the original style ribbed design on the base of the mirror as shown above. Available with, or without Bow Tie. If you want an exact replacement, these are the mirrors you ll need! Each mirror includes: the bracket, gasket and mounting screws. Fit LH or RH sides. 2 required per vehicle. CM with Bow Tie ea without Bow Tie ea Bow Tie Door Outer Mirror Reproduction Chevrolet Bow Tie mirror for models. Correct base with highly polished chrome. Mirrors include mounting gasket and screws. Fits LH or RH sides LH or RH ea front view Ribbed Outer Door Mirror Replacement mirror for all standard Nova models. Reproduction mirrors include the bracket gasket and screws. Features authentic ribbed base just like the original! LH ea RH ea Features Bow Tie emblem engraved on the back of the mirror as shown above Bow Tie Outer Mirror Correct reproduction accessory outer door mirror featuring a ribbed neck and a Bow Tie emblem cast into the rear of the mirror head. Each reproduction mirror includes the bracket, gasket and mounting screws LH or RH ea 1968 Outer Remote Mirror Exact reproduction 1968 Chevy II/Nova driver side remote mirror assembly including the mirror, cable, mounting bracket, gasket and screws LH ea A94101 A Clear Shot Door Mirrors Clear Shot Mirrors by Morris Classic Concepts can help with the common passenger side blind spot that exists with other mirrors. The patented design eliminates the passenger side blind spot by allowing the mirror to be adjusted further in without the need of a convex mirror. They also have built-in tensioning screws that lock the mirror heads into place and mounts to your car like the factory intended. Mirrors feature original style ribbed bases. Includes mounting gaskets and hardware. Sold in pairs. A round mirrors pr A rectangular mirrors pr Smooth Non-Ribbed Base Body Components H Remote Door Mirror Reproduction remote mirror for models. Includes: the correct length cable, gasket, and early style interior chrome bezel along with a highly polished triple chrome finish LH ea Features Bow Tie emblem engraved on the back of the mirror as shown above Bow Tie Outer Mirror Correct reproduction outer door mirror with the correct Bow Tie emblem engraved on the rear of the mirror. Each reproduction mirror comes complete with: the mounting bracket, mirror to body gasket and mounting screws. CM LH or RH ea CM Outer Door Mirror Replacement mirror for all standard Nova models. Reproduction mirrors include the bracket gasket and screws. Note: Does not include rib design. Specify LH driver or RH passenger mirror when ordering. CM LH ea CM RH ea 250 Outer Door Mirrors Toll Free Order Line

46 Outer Door Mirror Components Outer Door Mirror Mounting Set Contains the hardware to install a standard (nonremote) mirror onto either the driver or passenger side door. Each mirror mounting set contains the exterior mirror mounting bracket, the mirror base to body gasket and the mirror mounting screws. R LH set R RH set Bullet Mirror Mounting Gasket Correct replacement gasket used to install bullet mirrors. For LH remote mirror or manual RH mirror LH or RH ea R Bullet Door Mirror and Parts OER reproduction mirrors for Nova models. These mirrors were optional from The drivers side mirror is remote and includes the cable assembly and adjustment knob. Each mirror is ready to prep and paint to desired color. Bracket, gasket and mounting screws available separately. Note: The RH bullet mirror does not include the words Objects In Mirror Are Closer Than They Appear. This verbiage was featured on replacement GM mirrors appearing much later in the decade. Bullet Door Mirrors LH remote ea RH manual ea Bullet Mirror Glass LH 5.1" x 2.9" ea RH 5.4" x 3.2" ea Bullet Mirror Mounting Kits R LH kit R RH kit Bullet Mirror to Mounting Bracket Screw ea Remote Mirror Pivot Plate This is a reproduction of the remote mirror pivot plate for Chevy II/Nova models with a remote outside mirror. CM ea Remote Mirror Mounting Kit OER offers an installation kit designed to install a remote outer door mirror. Includes: correct reproduction mirror mounting bracket, gasket and screw. R kit Bow Tie Mirror Gasket Quality molded mirror gasket for Chevy II/ Nova models. Fits as original between the mirror base and door. K LH or RH ea Outer Mirror Gasket The correct gasket originally installed on Chevy II/Nova to mount the mirror base to the car door. Note: Not for remote mirrors. Can be installed on either LH or RH door mirrors. K without Bow Tie ea Remote Mirror Mounting Gasket OER reproduction remote mirror mounting gaskets. Sold individually mounting gasket ea mounting gasket ea Outer Mirror Bracket The correct brackets originally installed on Chevy II/Nova models, to mount the mirror base to the car door. Each mirror bracket will attach an original or reproduction mirror to the door with Bow Tie ea K without Bow Tie 6.99 ea Outer Door Mirrors K C Remote Mirror Mounting Bracket OER reproduction remote mirror mounting bracket for LH remote mirrors ea ea C ea Bullet Outer Mirror Bracket The correct bracket used to mount the original bullet type outer door mirrors. The LH remote mirror bracket is cosmetically different from the RH bracket. Without Remote Mirror RH ea With Remote Mirror LH ea 251 Body Components H

47 Floor Pans 14614W Chevy II/Nova Floor Pan with Weld-Thru TM This floor pan for Chevy II/Nova models is manufactured to factory specifications. This steel reproduction with the new Weld-Thru TM primer features the transmission tunnel, drain holes, seat belt anchors and factory style ribbing for added strength. Column Shifter 14614W AT without seat mounting brackets ea Floor Shifter 14392W AT without seat mounting brackets ea 14714W AT with rocker panels and bucket seat brackets ea 14715W MT w/rocker panels w/o seat mounting brackets ea Factory Contour Transmission Tunnel The transmission contour is replicated to exact factory specifi cations. Factory Style Drain Holes Each hole is pre-cut to the exact location of the original drain hole as shown. C9008W top view Body Components H Seat Belt Mounting Anchors Each fl oor pan features the pre-drilled mounting holes for seat belt installation Factory Style Ribbing For Added Strength The complete fl oor pan assembly is designed to exact factory specifi cations making sure that the structural integrity of each area is not compromised Chevy II/Nova Floor Pans This unique stamped steel reproduction is designed to offer the restoration enthusiast the finest in OEM quality and appearance. Our quality, one piece floor pans offer less hassle for installation and no patched seams for a cleaner restoration with greater strength and durability than a patchwork of sheet metal pieces. Save hours of costly body shop labor when welding in one panel instead of many. EDP coated Column Shifter and Automatic Transmission seat mounting brackets not included ea Floor Shifter and Automatic Transmission seat mounting brackets not included ea Floor Shifter and Automatic Transmission with rocker panels and bucket seat mounting brackets ea Floor Shifter and Manual Transmission with rocker panels, seat mounting brackets not included ea Automatic Transmission seat mounting brackets not included ea C9008W underside view Floor and Trunk Pan Don t mess around with patching your floor and trunk section one at a time. If the floor pan in your Chevy II/Nova is damaged or cancerous in multiple places, simply replace the whole pan at once. Superb, all-new reproduction of the entire original floor pan assembly and trunk pan offers less hassle of installation and no patched seams for a cleaner restoration and greater strength and durability than a patchwork of sheet metal pieces can offer. Plus, save hours of costly body shop labor when welding in one panel instead of many. This unique reproduction is designed to offer the restoration enthusiast the finest in OE quality. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. C9008W Weld-Thru TM ea 252 Floor Pan Toll Free Order Line

48 Floor Pans N12077 E Full Length Floor Pan Replace your existing floor pans with Classic Industries high-quality reproductions! Each floor pan is manufactured to exact specifications. You can now choose between the standard style replacement and the floor pan that includes the under rear seat metal and the toe board section. Each panel includes the correct drain hole area as a solid section built right into the panel. You may cut this section out when installing to put the original drain plug back in if desired. These are truly the finest quality floor pans available. You ll find the fit and quality extremely close to the originals. The seat track mounting area is not included and must be removed from existing panel and reinstalled on to reproduction panel. E LH 27-1/2" W x 60" L ea E RH 27-1/2" W x 60" L ea N9000PR LH and RH floor pans E166211/ pr N LH with rear seat and toe board section ea N RH with rear seat and toe board section ea Floor Repair Panel Reproduction floor repair panels for models. Each panel features correct gauge steel, stiffening ridges, come EDP coated for rust prevention and have prepunched drain holes. Note: *Shipped oversize * LH front 21" W x 38-1/2" L ea * RH front 21" W x 38-1/2" L ea LH rear 20-1/2" W x 24-1/2" L ea RH rear 20-1/2" W x 24-1/2" L ea E front LH panel E front LH panel E E167211B Full Length Floor Pan Factory style replacement floor pan sides for models. Available in your choice of our Restorer s Choice TM, manufactured in OE gauge steel, featuring all original contours and details or our more economical standard replacement for the car builder on a budget. Each floor pan comes finished in black EDP coating for rust prevention and features pre-punched drain holes. Restorer s Choice TM E167211B LH 21" W x 64" L ea E167212B RH 21" W x 64" L ea Standard Replacement E LH 21" W x 64" L ea E RH 21" W x 64" L ea N LH floor pans pr & RH E rear LH panel E rear LH panel Partial Floor Pan Each partial floor pan is manufactured to exact specifications. You may order the front section or the rear section for either side as desired. Each partial panel includes the correct drain hole area as a solid section built right into the panel. You may cut this section out before installing the panel to put the original drain plug back in if desired. The seat track mounting area must be removed from the existing panel and reinstalled on to the reproduction panel. Note: Shipped oversize. *Shipped double oversize. E * LH front 27" W x 30-1/2" L ea E * RH front 27" W x 30-1/2" L ea E * LH rear 27" W x 30-1/2" L ea E * RH rear 27" W x 30-1/2" L ea E LH front 20" W x 27-3/4" L ea E RH front 20" W x 27-3/4" L ea E LH rear 20" W x 28" L ea E RH rear 20" W x 28" L ea Body Components H Full Length Floor Pans 253

49 Floor Panels Floor Pan Halves with Toe Board Reproduction floor pan halves with toe board for Nova models. Manufactured to factory specifications featuring original style stiffening ribs, pre-punched drain holes, and EDP coated for rust prevention. These panels repair the area from the rear foot area up to the toe board LH ea RH ea Floor Repair Panel Reproduction floor repair panels for Nova models. Manufactured to factory specifications featuring correct contours and come EDP coated for rust prevention. Available as quarter repair sections, front section with toe board and rear section LH front 29-1/2" W x 43-1/2" L ea RH front 29-1/2" W x 43-1/2" L ea LH rear 28-1/2" W x 25" L ea RH rear 28-1/2" W x 25" L ea Toe Board Panel Reproduction toe board panels for Nova models. Manufactured to factory specifications featuring correct contours and come EDP coated for rust prevention. Available as a 1 piece panel or in halves. Note: *Shipped double oversize * piece ea LH ea RH ea Rear Seat Floor Panel Reproduction rear seat floor panels for Nova models. Manufactured to factory specifications featuring correct contours and come EDP coated for rust prevention. Available as a 1 piece panel or in halves. Note: *Shipped double oversize * piece ea LH ea RH ea Body Components H Front Floor Panel Reproduction front floor panels for Nova models. Manufactured to factory specifications featuring correct contours and come EDP coated for rust prevention LH ea RH ea Trunk Gutter Brace Reproduction of the original trunk gutter side braces for Nova models. These braces mount behind the tailpanel and help support the trunk gutters in the rear corners LH ea RH ea 254 FLoor Panels Toll Free Order Line

50 Firewall/Floor Pan Support Floor Pan Plug Reproduction oval metal floor pan plug or rubber floor pan plug for floor pans and trunk pans. These plugs are not included with reproduction floor pans or trunk pans metal ea rubber ea N1008 N1003 N Floor Brace These stamped reproduction floor braces are designed to add support to the floor assembly of the vehicle. Use on the center section of the floor. N LH or RH front section ea N LH center section ea N RH center section ea Firewall Panel without AC Reproduction firewall panel for Nova models. Most original panels have either been drilled, cut or have simply rusted out. This piece solves the rust problem and features correctly formed and punched openings for the heater box, hoses, throttle and speedometer cables for simple installation. All panels are EDP coated for rust prevention without AC ea 15114W 15117W Firewall to Floor Braces Reproductions of the firewall to floor braces for Chevy II/Nova models. Replace your rusted out or damaged originals with these high-quality reproduction braces. Installs between the firewall and the front frame rails. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated pr 15117W Weld-Thru TM pr Firewall Repairing and patching a dented, rusted out or over-drilled firewall can be tedious, but now you can skip the headache and replace your Chevy II/Nova model s entire firewall with this reproduction firewall panel. Firewall to floor braces are not included with this panel, and sold separately. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated ea 15114W Weld-Thru TM ea Front Frame Rail Support Stamped steel reproduction of the front frame rail support for Chevy II/ Nova models. This support bolts onto the front frame rails above the sway bar ea C126L Floor Pan to Firewall Extension Replacement panels which extend from the leading edge of the front floor pan section to the firewall. This panel completes the floor pan section. Manufactured in the correct gauge metal and matches the original configuration. If you are planning on replacing your floor pans, you should replace your firewall extension panels as well. C126L LH ea C126R RH ea C126R 14647W Bucket Seat Frame Supports Reproduction of the bucket seat frame supports for Chevy II/Nova models. When replacing your seats, you might also need to replace the supports. Each support is manufactured to duplicate the original in fit and appearance. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated 4 piece set 14647W Weld-Thru TM 4 piece set Firewall. Floor Braces 255 Body Components H

51 Floor Pan Support Bucket Seat Supports Reproduction bucket seat support set for Nova models. Manufactured to factory specifications and EDP coated for rust prevention. This set includes the two supports that are welded over the transmission tunnel, as well as the outer seat mounting points set set Rear Seat Floor Pan Reproduction rear seat floor pan panels for Nova models. Manufactured to factory specifications featuring original style contours and EDP coated for rust prevention. Available as a 1 piece panel, or as a partial left hand and right hand. Note: *Shipped double oversize * piece ea LH ea RH ea N1409W Auto Shifter Hump with Studs Replacement steel shifter hump for Chevy II/ Nova models with floor mounted automatic transmission shifter. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. N EDP coated ea N1409W Weld-Thru ea Bucket Seat Brackets Reproduction of the bucket seat brackets for Nova models. This set does both seats piece set 14619W Under Rear Seat Floor Brace Reproduction of the under seat floor brace for models. These braces are located on rear section under the bench seat. Each brace is designed to fit exactly as the factory intended LH ea RH ea Shift Hole Reinforcement Ring Shift hole reinforcement ring for Nova models. Stamped steel shifter ring reinforces shifter hole in floor for mounting automatic shifter and 4-speed shift boot. This piece has often been cut-up or has rusted. Retainer ring welds to bottom side of the floor pan. A ea Body Components H Rear Frame Rail Floor Braces Correct reproduction front frame rail braces for Chevy II/Nova models. These stamped steel braces include two pieces for each side. One piece mounts between the frame rail and the inner rocker panel. The other piece provides the mounting point for the leaf spring front eye bracket. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated set RH EDP coated set 14619W LH Weld-Thru TM set 14618W RH Weld-Thru TM set B10010W Rear Seat Floor Pan Reproduction rear seat floor pan for models. Features the braces that install under the floor pan. Available with traditional EDP coating or in a Weld- Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. B EDP coated ea B10010W Weld-Thru ea Front Floor Pan Brace Reproduction of the front floor pan brace for models. Made of top quality steel to exact specifications, this brace will fit like the original. Note: Shipped oversize front ea Rear Seat Floor Brace Reproduction of the rear seat floor brace for models. These braces are located under the rear floor. Each brace is designed to fit exactly as the factory intended LH ea RH ea Rear Seat Floor Hook Reproduction rear seat floor hook for Nova models. This hook is welded to the rear seat floor and creates the mounting point for the front side of the bottom seat. Two required per vehicle ea B24004W Four-Speed Steel Shift Hump Replacement steel shift hump for Chevy II/ Nova models equipped with a 4-speed transmission and without a factory center console. This shift hump is manufactured in steel material. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. B EDP coated ea B24004W Weld-Thru ea Steel Shift Hump Classic Industries offers a replacement steel shift hump for Chevy II/Nova models. N with console ea 256 Floor Pan Support Toll Free Order Line

52 Sheet Metal Tools Blaircutter Blaircutters provide fast, accurate holes in materials up to 3/16" thick. Unlike hole saws, that rip and tear through the material, these cutters provide a quality, virtually burr-free hole. Available in seven sizes for 1/4" and larger drill chucks. Spring loaded pilot pops the slug from the cutter. Buy the set and save! Set includes: all cutters, arbor and 3 extra pilots. Note: D.O.C = depth of cut. Arbors and Cutters sold separately. Blaircutter Set piece set set Arbor For 1/4" and Larger Chucks with pilot pin ea Replacement Pilot piece set Cutters 3/16" D.O.C /4" ea /16" ea /8" ea /16" ea /2" ea /16" ea /8" ea Premium Spotweld Cutter When you have a lot of spotwelds to remove, step up to the premium spotweld cutters for longer life in today s high-strength body steels. These cutters have a heavier wall (.090") for extreme durability and two step geometry that splits the chips and helps clear them. Premium spotweld cutters have a fast cutting action and lasts for hundreds of spotwelds. They are for use in 3/8" or larger drill chucks. The spotweld cutters are available individually or in sets containing arbor, 3 cutters, your choice of 2 skip-proof or 2 standard pilots. Spotweld Cutter Set w/skip-proof pilot set w/standard pilot set Arbor with Cutter skip-proof ea standard ea Replacement Parts arbor ea pilot 3 piece set cutters 3 piece set Replacement Parts arbor ea pilot 3 piece set cutters 3 piece set Stick Lubricant Convenient 1.68 oz. tube is ideal for all Blair hole cutters. Softer than standard stick lubricants, it provides superior adhesion to the tool and can be used in place of cutting fluids on ferrous and nonferrous metals to increase tool life, improve cutting performance and easier slug removal oz ea Blair Holcutter Holcutters are not hole saws. They can produce holes 3 times faster and cleaner than hole saws in sheet metal up to 1/8" thick and have a dramatically extended tool life. Holcutters produce holes from 11/16" up to 3" diameter in sheet metal, rubber, gasket or fiber materials, and some plastics. Ideal for aftermarket installations, custom fabrication, trailers, or gauge installation. Arbor fits 3/8" drill chucks. Holcutters have a new, patented Quad-Lead Thread System for quick cutter changes. Buy the set and save! Holcutter set includes: arbor, hex washer, extra pilot and the following sizes of cutters, 7/8", 1-1/8", 1-1/4", 1-3/8", 1-3/4", 2" and 2-1/2". Note: D.O.C = depth of cut. Arbors and cutters sold separately. Holcutter Set set Arbor For 3/8" and Larger Chucks ea Replacement Pilot piece set Cutters 1/8" D.O.C /16" ea /4" ea /16" ea /8" ea /16" ea " ea /16" ea /8" ea /16" ea /4" ea /16" ea /8" ea /16" ea /2" ea /16" ea /8" ea /16" ea /4" ea /8" ea " ea /16" ea /8" ea /4" ea /8" ea /2" ea /16" ea /8" ea /4" ea /8" ea " ea Blair Cutter Sets Antenna and Access Holcutter Set Note: Each set includes: arbor, extra pilot drills and cutters as shown /8", 1" and 1-1/4" set Rustproofer Cutter Set Note: Each set includes: arbor, three 1/2" cutters, pilot and extra pilot with standard pilot set with skip-proof pilot set Paintless Dent Removal Access Hole Set Note: Each set includes: arbor with standard pilot, extra pilot and cutters as shown /4", 3/8", 1/2", and 3/4" set Rotabroach Cutter Sets Rotabroach annular cutters are ideal for sheet metal fabrication, Paintless Dent Removal and for cutting rustproofing arbor with cutter access holes without clogging. Unlike hole saws and twist drills that push and tear through materials, these cutters will make hundreds of holes in steel, sheet metal or plastics up to 1/2" thick with no deforming of stock, jagged edges or out-of-round holes. Arbors for Rotabroach cutters fit 3/8" and 1/2" handheld drill chucks and use either spring loaded pilots or skip-proof pilots which eliminate pre-drilling operations. Each set includes: arbor, hex wrench, center punch, extra pilot and a variety of cutters as listed. Note: D.O.C = depth of cut. Arbors and cutters sold separately. Rotabroach Cutter Set /16", 3/8", 7/16", 1/2", 9/16", 5/8", and 3/4" set mm, 10mm, 12mm, 14mm, 16mm, 18mm and 20mm set /8", 1", 1-1/8", 1-1/4", 1-3/8", and 1-1/2" set Arbor for 3/8" and Larger Drill Chucks /4" - 3/4" or 6mm - 20mm cutters with pilot pin ea /8" - 3/4" or 10mm - 20mm cutters w/skip proof pilot ea Arbor for 1/2" and Larger Drill Chucks /16" - 1-1/2" cutters ea 3 Pack Replacement Pilot pilot for arbor set pilot for arbor set pilot for arbor set Rotabroach Replacement Cutters Replacement cutters for Rotabroach cutter set. Available in a 3 pack or as individual cutters in a variety of sizes. 3 Pack Cutters 1/4" Depth of Cut for Use with Arbor Only /4" set /16" set mm set mm set mm set mm set 3 Pack Cutters 1/4" Depth of Cut for Use with or Arbor /8" set /16" set /2" set /16" set /8" set /16" set /4" set mm set mm set mm set mm set mm set mm set mm set mm set mm set mm set mm set Individual Cutters 1/2" Depth of Cut for Use with Arbor /16" ea /16" ea /8" ea /4" ea /16" ea " ea /16" ea /8" ea /16" ea /8" ea /16" ea /2" ea Body Components H Blair Body Tools 257

53 Quarter Panels Full Quarter Panel When General Motors discontinued this popular item a few years back, you could either pay the high price for an original NOS panel or resort to the quarter skins which were less expensive but difficult to install. Classic Industries changes all that by offering a reproduction quarter panel for 2 door hardtop models. Does not include sail panel area or full door jamb area. Small portion of metal near top of door jamb must be removed from original panel and rewelded to new panel LH ea RH ea Full Quarter Panel Not just a skin, a full quarter panel! That s right, a full quarter panel assembly ready to install! When General Motors discontinued this popular item, you could either pay the high price for an original NOS panel or resort to the quarter skins which were less expensive but difficult to install. Classic Industries changes all that by offering a full panel that features the correct door jamb area, reinforced bumper bracket area, and correct side marker cut-out holes for models. Careful attention is paid to packing and shipping to eliminate damages! These panels will fit 2 door models only LH ea RH ea Body Components H Full Quarter Panel Replace your original quarter panel with these reproductions. This is not just a skin, this is a full quarter panel! We offer a full, ready-to-install quarter panel, just like what came from the factory back in This full panel features the inner door jamb area, trunk seal lip and full sail panel. Don t just patch your rusted or dented quarter panel with pieces, replace it with an OE quarter panel LH ea RH ea Full Quarter Panel Not just a skin, a full reproduction quarter panel! That s right, a full quarter panel assembly ready to install! When General Motors discontinued this popular item, you could either pay the high price for an original NOS panel or resort to the quarter skins which were less expensive but difficult to install. Classic Industries changes all that by offering a full panel that features the correct door jamb area, reinforced bumper bracket area, and correct side marker cutout holes for models. Careful attention is paid to packing and shipping to eliminate damages! These panels will fit 2 door models only LH ea RH ea 258 Quarter Panels Toll Free Order Line

54 Quarter Panel Skins Quarter Skin Replace your original quarter panels with these reproduction skins. Each skin will install as original. This is an excellent replacement if you have rust around the wheel well areas. This panel offers a good fit and will install with minimal refitting. This is a partial quarter panel skin which extends to the center body line. Will eliminate all rust located around wheel opening. Each panel is manufactured to allow application of the chrome wheel opening moldings. These panels are excellent for convertibles due to the elimination of the sail panel area. Careful attention is paid to packing and shipping to eliminate damages! LH 2 door, 18" H x 75" L ea RH 2 door, 18" H x 75" L ea door jamb view Quarter Panel Skins with Door Jamb Replacement quarter panel skin for Nova models. Manufactured with correct heavy gauge steel using new tooling, these quarter panel skins replace about 80% of the rear quarter. These panels are ideal when replacing the upper sail section of the quarter panel is not necessary. Carefully patterned after original quarter panels, each skin features all correct mounting holes and flanges and includes the door jamb area for a complete replacement. The featured door jamb area makes aligning the quarter skin during installation much easier. Note. Shipped truck freight LH ea RH ea LH ea RH ea LH ea RH ea Quarter Panel Skin Reproduction quarter panel skins for your Nova. These correct skins are produced specifically for the models and feature the correct rear side marker light cutout. You will not have to guess at the proper location any longer. These panels will fit 2 door models only. Careful attention is paid to packing and shipping to eliminate damages! Not for Hatchback models LH ea RH ea LH ea RH ea LH ea RH ea Quarter Panel Skin Replace your original quarter panels with these reproduction skins. Each skin will install as original. This is an excellent replacement if you have rust around the wheel well areas. This panel offers a good fit and will install with minimal refitting. This is a partial quarter panel skin which extends to the center body line. Will eliminate all rust located around wheel opening. Each panel is manufactured to allow application of the chrome wheel opening moldings. Careful attention is paid to packing and shipping to help eliminate damages during shipping LH 2 door ea RH 2 door ea Quarter Panel Skin Replace your original quarter panels with these reproduction skins. Each skin will install as original except for the roof sail panel which is not included with this reproduction. This is an excellent replacement if you have rust around the wheel well areas. This panel offers a good fit and will install with minimal refitting. This is a partial quarter panel skin which extends to the top crease of the original quarter panel. Will eliminate all rust located around wheel opening. Each panel is manufactured to allow application of the chrome wheel opening moldings. Careful attention is paid to packing and shipping to eliminate damages! Not for Hatchback models LH ea RH ea Body Components H Quarter Panel Skins 259

55 Quarter Patch Panels NV201L Lower Rear Half Quarter Patch Panel These are patch panels that replace the lower rear quarter panel from the area behind the rear bumper to the middle of the wheel well. These are partial quarter panel skins that extend to the center body line. This is a common rust area, and this is an inexpensive way to correct that problem. These panels have the side marker lamp cutouts and extend approximately 9-1/2" above the wheel well. Important: Due to differences in the side marker holes, modifi cations may be required to match your original confi guration. Note: Shipped oversize LH 21" H x 56" L ea RH 21" H x 56" L ea PDN93L Rear Quarter Center Patch Panel Replaces the wheel opening area on the rear quarter panel. Covers the entire wheel opening including approximately 6" above the top of wheel opening. These patch panels are a great way of replacing the rusted out areas without purchasing an expensive used or new reproduction quarter panel. Note: Shipped oversize. NV201L LH 13" H x 31" L USA made ea NV201R RH 13" H x 31" L USA made ea LH 19" H x 48" L ea RH 19" H x 48" L ea Lower Rear Quarter Patch Panel Replaces the lower section of the rear quarter panel from the bottom portion behind the bumper area to the wheel opening. This patch panel will allow you to replace the commonly rusted area without replacing the entire quarter panel. Note: and are designed to fi t all models. Due to differences in the side marker holes, modifi cations may be required to match your original confi guration. PDN93L LH 10" H x 29" L ea PDN93R RH 10" H x 29" L ea NV200L LH 8" H x 32" L USA made ea NV200R RH 8" H x 32" L USA made ea LH 14" H x 36" L ea RH 14" H x 36" L ea LH 12" H x 32" L ea RH 12" H x 32" L ea W Body Components H Lower Front Quarter Patch Panel This patch panel replaces the lower front section from the front edge of the quarter panel to the center of the wheel well opening and extends up to the center body line. This patch panel will repair a commonly rusted out area on Nova models. A quality steel stamping, it extends approximately 9-1/2" above the wheel well LH 20" H x 33" L ea RH 20" H x 33" L ea Quarter Paneland Door Frame Reproduction quarter panel and door frame assembly for all Chevy II/Nova 2 door hardtop models. These unique pieces will replace the framework around the doors, across the roof line and down the quarter panel to the rear wheel well. Features the front kick panel area and the inner rear quarter area. Outer rocker panels are also featured. Some welding is required for installation. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated ea RH EDP coated ea TM 16124W LH Weld-Thru ea 16125W RH Weld-Thru TM ea 260 Quarter Patch Panels Toll Free Order Line

56 Wheelhouse Panels C W C Rear Outer Wheelhouse Panel Reproduction outer wheelhouse panels for Chevy II/Nova models. Each panel is an exact duplicate of the original. Note: Shipped oversize. C LH ea C RH ea N119W C Rear Wheelhouse Panel Reproduction wheelhouse panels for Nova models. Each panel is an exact duplicate of the original. Note: Shipped oversize. Inner Wheelhouse Panels LH ea RH ea Outer Wheelhouse Panels C LH ea C RH ea Rear Frame Rail Restore the structural integrity of your Nova by replacing the damaged, bent or rusted frame rails with these reproductions. Manufactured to exact factory specifications to replace the original rails exactly. Each frame rail covers the entire trunk area from front to rear. Classic Industries recommends professional installation. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated ea RH EDP coated ea 14617W LH Weld-Thru TM ea 14616W RH Weld-Thru TM ea LH EDP coated ea RH EDP coated ea N118W Rear Outer Wheelhouse Panel Reproduction outer wheelhouse panels for Chevy II/Nova models. Each panel is an exact duplicate of the original. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Note: Shipped oversize. N LH EDP coated ea N RH EDP coated ea N119W LH Weld-Thru TM ea N118W RH Weld-Thru TM ea 14380W 15192W Trunk Divider Reproduction trunk divider/package shelf for Nova models. Featuring all correct contours, back seat support bracing and rear speaker mounting locations, each panel will fit and install as original. Includes deck lid hinges and torsion rods. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated ea 15192W Weld-Thru TM ea F W 16121W Rear Frame Rail Rear Brace Correct reproduction rear frame rail braces originally installed on Chevy II/Nova models. These stamped steel braces mount between the outside of the frame rail and the rear tail panel under the trunk area. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics LH EDP coated ea RH EDP coated ea 14621W LH Weld-Thru TM ea 14620W RH Weld-Thru TM ea LH EDP coated ea RH EDP coated ea 14381W Rear Wheelhouse Panel Reproduction of the rear wheelhouse for Chevy II/Nova models. This is the inner and outer wheelhouse welded together. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Note: Shipped oversize LH EDP coated ea RH EDP coated ea TM 14380W LH Weld-Thru ea 14381W RH Weld-Thru TM ea Fiberglass Extended Wheel Well Openings Factory Nova models featured fairly small tires by today s standards. These cars cry out for bigger tire and wheel combinations which will not fit in stock form. The units increase to a 36" opening. The units increase the factory opening to 37" without altering the original width or height. Note: Shipped oversize. F pr F pr Body Alignment Shims Used to align body panels, these shims are available in various thicknesses to suit most alignment situations. Please check your originals to be sure you are ordering the correct size and number of shims. Sold in sets of 10. C mm set C2004 3mm set C2001 6mm set Body Components H Wheelhouse Panels 261

57 Trunk Pans Trunk Floor Drop Off Reproduction trunk floor drop off panels for Nova models. These panels fill the area between the trunk floor and quarter panel. Come EDP coated for rust prevention LH ea RH ea C W bottom view Trunk Pan C6835 Reproduction trunk pan available for Nova models. Each trunk pan is reproduced to factory specifications and will replace the entire bottom portion of the trunk area. Available as a full pan with the well section, the sides and the trunk floor brace or purchase the center section only. Note: *Shipped truck freight. **Shipped double oversize. Full Pan * ea ea Center Section C6834 ** /4" W x 31" L ea Side Extensions C LH ea C RH ea Full Trunk Pan with Frame Rail You can replace the whole trunk floor in your Chevy II/Nova in one piece. This is a reproduction of the full floor pan featuring the well section, the sides, the trunk floor braces and rear seat pan. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics EDP coated ea 14615W Weld-Thru TM ea N1633LW Trunk Floor to Quarter Panel Filler Reproduction quarter panel fillers located between the trunk pan extension and the quarter panel. Available as a set with fillers, or purchase separately. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. N1633L LH 11" tall x 28" long EDP coated ea N1633R RH 11" tall x 28" long EDP coated ea N1633LW LH 11" tall x 28" long Weld-Thru TM ea N1633RW RH 11" tall x 28" long Weld-Thru TM ea CM LH 11" tall x 27" long ea CM RH 11" tall x 27" long ea Body Components H C Nova Reproduction Trunk Pan Reproduction trunk pans are available for Chevy II/Nova models. Each trunk pan is reproduced to factory specifications and will replace the entire bottom portion of the trunk area. Available as a set with fillers, or purchase separately. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Note: *Shipped truck freight. Pan Set (3 piece set) C3869 * trunk pan set set Pan With Filler Panels Attached (1 piece) * EDP coated ea 14354W * Weld-Thru TM ea Center Section C3868 * /2" W x 39" L ea Filler Panels C filler panel LH ea C filler panel RH ea Trunk Floor Brace These replacement braces attach to the underside of the trunk pan and provide the anchor points for the fuel tank mounting straps. Will fit and install LH or RH. CM required ea required ea LH ea RH ea Lower Rear Cross Rail Replace your rusted lower rear cross rail on your Nova with this quality reproduction. This rail mounts underneath the rear end of the trunk floor. Note: Shipped oversize ea 262 Trunk Pans Toll Free Order Line

58 Rear Body Panels Center Tail Panel Reproduction center tail pan for Nova models. This piece finishes the lower trunk opening between the tail lamps. Features correct contours, EDP coating for rust prevention and includes the two wiring retainers ea Tail Lamp Panel Finally there s a solution to the rusty or damaged rear tail lamp panel on your Nova. We offer this quality reproduction which is stamped to match all of the factory body contours exactly. It s EDP coated for corrosion resistance and ready to prep and paint. N ea Tail Panel Reproduction tail panel for Nova models. Manufactured to factory specifications, with tail panel braces, and trunk lid striker included. Come EDP coated for rust prevention ea N2107W Tail Lamp Panel Classic Industries is offering this correct reproduction rear tail panel for models except wagon. This exact reproduction will install on all Chevy II/Nova models. Features mounting panel to install the tail lamp lenses. Manufactured in steel and EDP coated. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. N EDP coated ea N2107W Weld-Thru TM ea 14637W CM Rear Window to Trunk Panel Reproduction steel body panel that installs between the rear window and the trunk lid for hardtop models. Panel covers the area between the trunk and window. Available with or without the studs to mount the clips for the exterior rear window molding trim. Note: Shipped oversize. CM without clip studs ea with clip studs ea Upper Rear Outer Body Panel Reproduction upper rear outer body panel which installs between the rear window and trunk lid. Replace your missing, damaged or rusted upper rear body panel with this quality reproduction. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Note: Shipped oversize EDP coated ea 14637W Weld-Thru TM ea N2106W Tail Panel Set Replace the often rusty tail panel on your Chevy II/Nova. These panels form the lower trunk ledge above the rear bumper area and will fit all models except wagons. Manufactured in original gauge steel to match your Nova s contours. Available with traditional EDP coating or in a Weld-Thru TM primer that requires minimal preparation, eliminates corrosion between overlapped panels, and promotes superior weld characteristics. Note: Shipped oversize. N EDP coated set N2106W Weld-Thru TM set N Tail Lamp Panel Reproduction rear tail lamp panel for models. This exact reproduction will install on all Chevy II/Nova models. Features the mounting panel to install the tail lamp lenses. Manufactured in steel and EDP coated ea ea N Chevy II/Nova Tail Lamp Mounting Panel Reproduction tail lamp mounting panels originally installed on Chevy II/Nova models except station wagons. N LH ea N RH ea N LH ea N RH ea Trunk Gutter Brace Reproduction trunk gutter side braces for Nova models. These braces mount behind the tail panel and help support the trunk gutters in the rear corners LH ea RH ea LH ea RH ea LH ea RH ea Body Components H Rear Body Panels 263

59 Trunk Lids Rear Cross Rail Replace the bent, damaged or rusted original rear cross rail on your Chevy II/ Nova. The rear cross rail installs behind the rear bumper and it mounts to the tail panel and the lower rear cross rail features the upper and lower rear cross rail. Note: Shipped oversize upper rear cross rail only ea rear cross rail assembly ea Nova Trunk Lid Reproduction trunk lid for Chevy II/Nova models. Each trunk lid is manufactured and stamped from steel as original. Features EDP coating to prevent rust. Important: *Modifi cations of lock hole is required to obtain proper clocking of lock cylinder A * except hatchback ea B except hatchback Restorer s Choice TM ea Rear Cross Rail Filler Reproduction rear cross rail filler panels for all Nova models. These filler panels are spot welded at the end of the lower rear cross rail and fill the space between the trunk floor and the rear cross rail LH ea RH ea F Fiberglass Pin-On Style Trunk Lid This is a fiberglass replacement of the original trunk lid assembly for Chevy II/ Nova. These high-quality replacements may be used for street, strip or show use. No provision for stock hinges. Attach with pins or fasteners. F pin-on style ea F pin-on style ea Body Components H Package Tray Panel Reproduction rear package tray panel for Nova models. Manufactured to factory specifications from new steel tooling, featuring pre-made speaker openings and EDP coated for rust prevention ea Chevy II/Nova Trunk Lid Reproduction trunk lid for Chevy II/Nova models. Each trunk lid is manufactured and stamped from steel as original, EDP coated to prevent rust. Will replace the factory trunk lid exactly. N ea N ea ea C68081CG Carbon Fiber Trunk Lid Lightweight carbon fiber trunk lids for Chevy II/Nova models. This trunk lid is available in 100% carbon fiber or with a carbon fiber top layer and fiberglass understructure. Each style is available in your choice of satin or glossy finishes. Either choice offers both a great look and significant weight reduction. 100% Carbon Fiber Trunk Lid Wet Carbon Fiber Construction C68081CG gloss finish ea C68081CS satin finish ea C68082CG gloss finish ea C68082CS satin finish ea Dry Carbon Fiber Construction C68081DG gloss finish ea C68081DS satin finish ea C68082DG gloss finish ea C68082DS satin finish ea Carbon Fiber/Fiberglass Trunk Lid gloss finish... C68081FG ea C68081FS satin finish ea C68082FG gloss finish ea C68082FS satin finish ea 264 Trunk Lids Toll Free Order Line

60 Trunk Components Chevy II/Nova Trunk Lid Hinges Reproduction trunk hinges for Chevy II/ Nova models. These high-quality reproductions are manufactured to exact specifications and will replace your rusty or damaged original trunk hinges. Sold as a pair. B pr FB1054BF Billet Nova Trunk Hinges Looking for an eye catching mod for your classic Nova? Replace your original stamped steel trunk hinges with these beautiful billet aluminum hinges which replace the bulky and ugly torque rods with gas struts to support the decklid. No modifications needed for installation. Hinges are made the finest quality 6061-T6 aluminum and use weatherproof bearings and stainless steel hardware to ensure proper operation in any climate. Engineered for smooth, effortless operation. Each hinge is machined to perfection in a manner which is not only fully functional but visually appealing as well. Comes with black carbon steel struts and mounting hardware. Available in polished, black anodized or natural finish. Polished Aluminum Two Door Models FB1073PF fiberglass trunk lid set FB1073PS steel trunk lid set FB1054PF fiberglass trunk lid set FB1054PS steel trunk lid set Four Door Models FB1074PF fiberglass trunk lid set FB1074PS steel trunk lid set Anodized Black Two Door Models FB1073BF fiberglass trunk lid set FB1073BS steel trunk lid set FB1054BF fiberglass trunk lid set FB1054BS steel trunk lid set Four Door Models FB1074BF fiberglass trunk lid set FB1074BS steel trunk lid set Natural Aluminum Two Door Models FB1073NF fiberglass trunk lid set FB1073NS steel trunk lid set FB1054NF fiberglass trunk lid set FB1054NS steel trunk lid set Four Door Models FB1074NF fiberglass trunk lid set FB1074NS steel trunk lid set Trunk Hinge Torsion Rods Torque rods are essential for keeping your trunk stable in the open position. The torque rods apply pressure to the hinge to allow the trunk lid to remain open. These replacement torque rods feature the proper tension specifications and feature a black wrap for an original appearance torsion rods pr Power Trunk Release The Klassic Keyless system is a complete do-ityourself set designed specifically to fit your Nova, and Nova SS. In this power trunk release set you will receive: 1 Power trunk latch, 1 manual push button, wire and wire loom, full color step-bystep instruction manual, trimming template, and all necessary hardware. This is everything you will need to install a factory style power trunk release system in your classic car. Note: May require some minor sheet metal trimming on some vehicles for installation. KK set Power Trunk Lock Conversion This set is designed to convert your vehicles manual trunk release to power release. A great addition when installing power door locks or a keyless entry system. Includes: actuator, push button, brackets and wiring. PTL set Electric Trunk Release Add a modern touch to your classic Nova, an electric trunk release. Set comes with: latch, modified catch, bolts, wiring, electrical connectors, push button switch, and detailed instructions. Note: Some metal trimming required, template included. M set Trunk Lid Catch Mount Reproduction trunk lid catch mount for Nova models. This EDP coated piece is welded to center tail panel and acts as the mounting point for the trunk lid catch ea Trunk Lid Striker Reproduction trunk lid striker for all Nova models. Manufactured to factory specifications and EDP coated for rust prevention ea ea shown mounted in trunk Trunk Lock Striker Anchor Plate This is a high-quality reproduction of the trunk lock striker anchor plate. This stamped steel plate is welded onto the center of the rear body panel, inside the trunk. The trunk lock striker plate bolts into the center of this plate ea Trunk Lamp Replacement Bulb Correct replacement bulb for Nova models. Replaces the trunk lamp bulb on models equipped with a trunk lamp ea Trunk Lid Guides Reproduction trunk lid guides for all Nova models. Sold as a pair pr Trunk Lid Bumper Correct replacement rubber bumper which applies to the body and lid assembly for models. Sold individually. 2 required ea A ea Rubber Trunk Floor Pan Plug These rubber plugs are designed to keep air and water from entering the trunk area. They are also used in other locations including tail gate, floor pans, lock and hinge pillars, roof panels and crossmembers on various models throughout the GM line from /4" i.d. hole ea /16" i.d. hole ea Body Components H 265

61 Trunk Components black/gray Body Components H Trunk Lid Latch Reproduction trunk lid latch assembly originally installed on all Chevy II/Nova models. Will install as original using existing hardware. Also available for the electric trunk latch option standard ea electric ea Trunk Latch Assembly This is a reproduction replacement trunk latch assembly. This unit installs in the trunk area and is connected to the trunk lock cylinder by the handle shaft. Note: This assembly does not include the shaft or lock cylinder assembly. Available separately ea Space Saver Tire Infl ator Bracket Reproduction bracket used to hold the space saver spare tire canister in place. C early style ea C late style ea Spare Tire Clamp Anchor Plate Correct anchor plate for all models. This plate is used to secure the spare tire to the trunk ea C Spare Tire Hold Down Rod Reproduction hold down rod used with all Chevy II/Nova models. We offer the spare tire hold down rod and nut for a complete replacement rod 9 1/2" ea nut ea Jack Wrench Storage Sleeve Correct replacement storage sleeve for jack wrench assembly /4" wide ea /4" wide ea K79000B Jack Storage Bag Handy jack and load rest bracket storage bag with snap lock. Produced with reproduction Houndstooth felt backed material. Fits original jack assembly. K79000B black/aqua ea K79000A gray/black ea Jack Wrench Make sure you don t get stuck somewhere without a jack wrench! G /4" hex ea Jack Base Reproduction of the jack base for models. The correct 1969 base is available and features the date code U69 that was correct for 1969 models only ea (Date Coded-U69) ea Bumper Jack Assembly Reproduction bumper jack assembly for Chevy II/Nova models. The assembly features a three piece set. Includes base and jacking mechanism. The jack load rest bracket is not included. Note: Due to the inherent dangers of this type of jack, it is recommended for show use only set OER Trunk Refi nish Kit Restore the trunk area of your classic car to a factory original appearance and provide the ultimate protection from the elements. First prime the area to be painted. On bare metal, you should use a self etching primer. Next, spray your base coat. Then spray your spatter coat and let dry thoroughly. Finally, coat the entire surface with our clear topcoat to seal the surface. Buy the kit and save! Note: Ships ground only. No air shipment. Complete Trunk Refi nishing Kit Contains everything you need to refinish the trunk of your classic vehicle including 2 cans of primer, 3 cans of spatter paint and 2 cans of clear topcoat. With Standard Gray Primer K51490 black and gray kit K51491 black and aqua kit K51492 gray and white kit With Self Etching Gray Primer K51493 black and gray kit K51494 black and aqua kit K51495 gray and white kit Trunk Refinishing Components Need an extra can of a component? Primer Only 20 oz. Cans K89576 std. gray primer ea K89560 self etching gray ea Base Coat Only 20 oz. Cans K89578 flat black ea K89581 dark gray ea Spatter Coat Only 16 oz Cans K51496 black and gray ea K51499 black and aqua ea K51498 gray and white ea Clear Topcoat Only 16 oz Cans K51497 clear topcoat ea OER Trunk Spatter Paint Restoration grade spatter paint for the discriminating restorer who wants to accurately replicate the original texture and finish in their trunk. Produced by the original manufacturer for an authentic texture and color match. These water soluble paints are designed to be applied with K86130 a paint gun and do not require a clear coat. One quart required per vehicle. Includes instructions. Important: GM originally applied trunk spatter paint with a Binks 2100 gun with a 200 tip and a 66 fl uid nozzle with an internal mix aircap. K86130 quart black and aqua ea K86131 quart gray and white ea Central Pneumatic General Purpose Spray Gun This general purpose paint spray gun black/aqua gray/white is designed with a rugged lightweight body that makes it easier to keep a steady hand while you paint. The spray gun sprays all light-to-medium viscosity materials including lacquer, enamel, urethane, polyurethane and primer. This is a great paint spray gun for a wide range of uses in any home garage or professional auto shop. A ea 266 Trunk Components Toll Free Order Line

62 Trunk Accessories Add or replace the original trunk mat with an all new Classic Industries reproduction. Guaranteed to fi t perfectly! A A A blk/gray Crowsfoot sample patterns N76007 blk/aqua Houndstooth blk/aqua Herringbone blk/gray Herringbone Nova Reproduction Trunk Mat Excellent quality reproduction mats installed on Chevy II/Nova models, except hatchbacks. Each trunk mat is specifically die-cut for your particular year. Restore your trunk area by first painting the trunk with OEM type spatter paint for an original appearance and protection. Then install your new trunk mat. Your trunk area will look factory new again! Rubber Trunk Mats N rubber black/gray Herringbone ea N rubber black/gray Crowsfoot ea N rubber black/aqua Houndstooth ea N rubber black/gray Herringbone ea N rubber black/aqua Herringbone ea Foam/Felt backed Trunk Mats N felt backed vinyl black/aqua Houndstooth ea N foam backed felt black/aqua Herringbone ea N foam backed felt black/aqua Houndstooth ea N foam backed felt black/aqua Herringbone ea Perfect Looking Trunk! Nova Trunk Panel Set This trunk panel set is the perfect way to beautify your trunk area. There s no need to spend big bucks having it professionally paneled when this pre-cut set fits in place exactly. Panels can be covered with vinyl, cloth or even carpet to achieve whatever custom look you desire. CM set These two stage trunk insulation kits feature: Dynamat Xtreme damper pads, Heat Shield insulator panels, spray adhesive, and sealing tape Rubber trunk mat Illustrated installation instructions detailed shot of molded 3D logo Quiet Ride AcoustiTRUNK Insulator & Trunk Mat Kit Pre cut, ready-to-install insulation and rubber trunk mat kit! Most vehicles have little or no insulation in the rear trunk floor area of the vehicle. QuietRide s new AcoustiTrunk Floor Mat and Insulation kits can help you stop the noise, vibration and heat and dress up the trunk area as well! This is a great solution to quiet down the trunk of your car, while adding a custom touch. Your choice of smooth, no logo design, or a 3D raised logo trunk mat. Important: All models, except wagons. Note: Shipped double oversize and ground only (no air shipments) due to aerosol spray adhesive A without logo kit A Nova script logo kit A without logo kit A Nova script logo kit A without logo kit A Nova script logo kit RJ Trunk Partition and Padding Rear Seat to Trunk Partitions Shelf fits directly behind the rear seat and covers area between the trunk and back seat section. Rear jute which attaches to partition sold separately. Note: Shipped oversize. N black ea N black ea N black ea N black ea Trunk Partition Jute Padding Original material jute padding which attaches to the trunk partition. Eliminates noise and helps insulate the trunk area. Note: Use 3M spray adhesive part #08090 for installation. RJ ea RJ ea RJ ea RJ ea K78007B Spare Tire Cover Reproduction spare tire cover manufactured in the correct aqua/ black or black/gray Houndstooth, Herringbone, Crowsfoot pattern. Each tire cover is specifically designed for 13", 14" or 15" spare. Fiberboard Tire Cover Houndstooth K " black/aqua ea K78007A 14" black/gray ea K78008A 15" black/gray ea K78007B 14" black/aqua ea K78008B 15" black/aqua ea Herringbone K78011C 15" black/aqua ea Crowsfoot K " black/gray ea Felt Backed Tire Cover Standard Houndstooth K78000A black/gray ea K78006A black/aqua ea Space Saver Houndstooth K78000B black/gray ea K78006B black/aqua ea Body Components H Trunk Accessories 267

63 Windshield Wiper A40119 A Wiper Motor Arm Reproduction stamped steel wiper motor arm that includes the hardened ball stud for models. This arm connects the wiper motor to the wiper transmission. KW ea A40121 A Wiper Motor to Firewall Seal Remanufactured Wiper Motor Our remanufactured wiper motors are the high-quality, low cost alternative to brand name motors. Why pay more?! Enjoy safety, performance, and reliability at a fraction of the cost of OE. We ll back that up with a 1-year manufacturer s limited warranty. A speed ea A speed 3 terminal ea A speed 4 terminal ea A all ea Circular seal fits between motor and firewall which prevents water from entering through the firewall area. This is a small gasket that can keep your interior free from water which can ruin your carpet and rust your floor pans. CA ea CX1755 CX Windshield Wiper/Washer Switch Replace your inoperative windshield wiper switch with one of these top quality reproduction switches. Manufactured to fit and function just like the original. CX single speed ea CX speed ea CX single speed ea speed ea Selecta-Speed Wiper Motor Classic Industries offers this great upgraded wiper motor for Chevy II/ Nova models. The Selecta-Speed wiper system contains a low profile, seven speed wiper motor (with five different delays, a low and a high speed), rotary switch (complete with a billet knob), adapter plate and wire harness. The CNC aluminum adapter plate mounts the wiper motor to the stock firewall bolt pattern. Note: This set includes a rotary wiper switch to replace the original slider switch. The dash must be modifi ed for new switch to fi t, and there is no provision to operate the windshield washer function. D wiper motor set set D wiper motor set set D wiper motor set set wiper motor set set billet headlight knob ea Windshield Wiper Switch Reproduction windshield wiper switches for Chevy II/Nova models. The switch features a later style knob with the word PUSH, as opposed to the original vertical rib style ea ea Body Components H Wiper Motor Grommets OER reproduction grommets used to mount the wiper motor to the firewall. These reproductions feature the original type steel sleeve built directly into the grommet, ground strap and screws with lock washers set Windshield Wiper Switch Reproduction of the windshield wiper switch for Nova models. Replace your inoperative windshield wiper switch with this quality reproduction. Manufactured to fit and function just like the original ea 268 Windshield Wiper Toll Free Order Line

64 Windshield Wiper K Windshield Wiper Knob Reproduction of the chrome wiper knob for Chevy II/Nova models. This is a chrome reproduction knob which will install on your wiper switch arm as original. Will help add new life to your dash area ea K ea Intermittent Wiper Module This Intermittent Wiper Module adds three settings to the factory slow and fast speeds. Uses existing switch and motor for a stock look. Installs behind the dash between the switch and harness. Fits most applications with two-speed and non-hiding wipers. RE ea Windshield Washer Pump Replacement windshield washer pumps for Nova models. The pump circulates water from the windshield washer jar to the washer nozzles. This is a Delco service replacement part which may differ cosmetically from the original motor. However, it will fit and function correctly. Note: For use with Delco wiper motors. Not for use with remanufactured motors with black nozzles ea with white nozzles ea ea Washer Pump Repair Set This repair set will replace the top of the pump which includes: the hose connections, the pump gaskets and mounting screws. The set is designed to restore the pumping action of your windshield washer system. You may choose to rebuild your original washer pump as opposed to replacing it if you want to maintain originality. The service replacement pumps will differ slightly cosmetically from your original. That s why we offer these rebuild sets! set Wiper Transmission Mounting Screws Reproduction wiper transmission mounting screws for Nova models. These are the correct screws that are used to mount the wiper transmission and feature the correct head style with washers included set Two-Speed Hidden Windshield Wiper Conversion Our wiper system is a modern, high-quality replacement for the old system. It is the only replacement wiper system that is completely hidden, fitting entirely within the airbox in the cowl! This allows you to remove the stock wiper motor. The wiper motor hole in the firewall can be covered up with the cover plate supplied in the set or you can weld in a patch panel to eliminate the hole entirely. Perfect for Pro Street cars or if you just desire a clean looking firewall. For models with concealed wipers. Important: Very minor modifi cation is required to run the wiring through the fi rewall standard 2-speed system set with delay switch set standard 2-speed system set with delay switch set Body Components H Windshield Wiper 269

65 Windshield Wiper K AERO Wiper Blades High-quality OER reproductions of the AERO style wiper blades for models. These AERO blades are designed to better hold the rubber against the glass for a better wipe, and reduce blade lift at highway speeds. K " blades pr " blades pr detail detail Silicone Blade A somewhat confusing aspect of the apparent inadequacy of traditional rubber wiper blades is that they have not fundamentally improved since invented almost 100 years ago. Since 1910 consumers have patiently put up with the necessity to replace worn or deteriorating wiper blades every 12 to 18 months. An interesting note is that the average consumer will often wait 2.3 years before replacing their wipers, often waiting until visibility in poor driving conditions becomes far too dangerous to overlook. Today s Silicone technology may very well render the conventional rubber wiper blade obsolete. Of all material researched throughout the world, one rose to the top as the natural choice for the wiper for the next millennium... Silicone! Superior wiping in the harshest of weather conditions, will not deteriorate like rubber even after years of use. Silicone blades will remain soft and flexible even after extended exposure to ozone, ultraviolet rays, ice, snow, and heat. Silicone can handle grueling temperatures even as high as +350 degrees F. Change your blades, and when the rain starts to fall, you will have confidence that your silicone blades will be ready " silicone blade ea " silicone blade ea " silicone blade ea " silicone blade ea " silicone blade ea Windshield Washer Hose Set Reproduction set includes replacement style ribbed hoses pre-cut to factory lengths, correct pickup screen, tie straps and installation diagram replacement style set Windshield Washer Hoses Original style hose set features the correct thin wall style ribbed hoses. 2 hoses cut in the correct length. K original style set Spray Connector Tee Correct original GM replacement T-connector for all models. G ea G Windshield Wiper Blade/Insert Wiper blade assembly and inserts for Chevy II/ Nova models. These blades will replace your worn out or missing originals. Available for both Anco and Trico style wiper blades. Sold individually. Reproduction Blade Assemblies GS Anco, 15-5/32" pr Trico, 14-7/8" ea G Trico, 14-7/8" GM ea Trico, 14-7/8" repro 7.99 ea Windshield Washer Nozzles Exact in every way, these are a top quality reproduction windshield washer nozzles for Chevy II/ Nova models. A pr Washer Hose Tie Straps Straps used to hold windshield washer hoses to fenderwell. Three straps included. K set Body Components H Windshield Wiper Transmission Reproduction of the windshield wiper transmission for Chevy II/Nova models. These are top quality and include all links and pivots from the wiper motor to the spline output shafts that the wiper arms attach to. N ea Windshield Washer Nozzles Replace your old clogged nozzles with these reproduction windshield washer nozzles. Fits all Chevy II/Nova models pr Optikleen Washer Bottle Decal Exact reproduction washer bottle decal for Chevy II/Nova models with Optikleen washer bottle. Each decal includes the correct type style with instructions for anti-freeze, bug removal and temperature ratings. DC Optikleen decal ea 270 Windshield Wiper Toll Free Order Line

66 Windshield Wiper Universal Washer Bottle and Pump Kit Universal washer bottle and pump for Nova models. This kit is for when you need a low maintenance highquality washer pump and bottle. MP ea Windshield Washer Jar OER replacement jar which holds the windshield washer fluid. This jar is for Chevy II/Nova models. The washer cap is sold separately ea Washer Jar Bracket Replacement bracket which mounts the washer jar onto the radiator support. For Chevy II/Nova models. This bracket holds the washer jar in place reproduction ea Washer Jar Bracket Correct stamped steel reproduction windshield washer jar bracket ea WB125 Glass Windshield Washer Bottle Reproduction glass windshield washer bottle with antifreeze/washer solvent lettering on cap. This complete replacement set includes the mounting bracket. For use on virtually all early GM models WB125 bottle, cap and bracket set WB126 replacement cap ea Windshield Washer Jar Replacement jar which holds the windshield washer fluid. This specially configured washer jar was only installed on Nova models. The washer cap is sold separately reproduction ea G GM ea Washer Jar Fluid Screen The correct replacement filter screen used to eliminate dirt and other residue which could clog the washer hoses, water pump or washer nozzles. Replace your screen periodically for best results ea Washer Jar and Bracket Kit Includes the bracket, bottle and cap. Is your original washer jar damaged? Is your bracket bent beyond use? Maybe it s time to replace your originals with Classic Industries washer jar and bracket kit. The kit includes: the correct washer jar, attaching bracket and washer jar cap. We now offer this unique kit which fits 1968 through 1970 Chevy II/Nova models! Each kit includes the correct mounting bracket for installation. K standard kit Windshield Washer Jar This OER reproduction windshield washer jar holds the windshield washer fluid. This jar is for all Nova and X-Body models. Note: The washer cap is sold separately ea G Windshield Washer Jar Cap These replacement caps are for washer jars. Original GM service replacement parts or Original Equipment Reproduction for years listed OER ea G GM ea Body Components H Windshield Wiper 271