INSTALLATION MANUAL. SKYLINE ROOF RACK Toyota Tacoma 3 rd Gen (2016+)
|
|
- Derick Chapman
- 5 years ago
- Views:
Transcription
1 INSTALLATION MANUAL SKYLINE ROOF RACK
2 Installation Time = 1 Hour Difficulty = Intermediate CONTACT US GET TMT4x4 Sales@TMT4x4.com
3 03 WARNING! READ ALL SAFETY MESSAGES AND UNDERSTAND ALL INSTRUCTIONS AND PROCEDURE NOTICES BEFORE ATTEMPTING TO INSTALL OR USE THIS PRODUCT! - Ideal accessory for SR, SR5, TRD Sport, TRD Off-Road, Limited and TRD Pro models of Toyota Tacoma 3 rd Generation (2014+) with Double Cab (4-Doors). This TMT rack does not fit to Tacomas with Access Cab (2-Doors). - The installation of this product may require the use of specialized tools and techniques. It is recommended that only be installed by trained personnel. - All products built and designed by TMT are intended for off-road use and should be assembled, installed, and used according to TMT s recommendations. - All attachment points should be checked when you first install your rack. You should also inspect it periodically and each time they are reinstalled.
4 04 CARRYING LOADS Maximum Load Capacity: Please refer to your vehicle manufacturer s handbook for maximum roof load capacity. Handling Change: Don t overload your vehicle s hood to the point of difficult maneuverability. Be especially careful in off-road conditions and when transporting wind-resistant loads. Location of Loads: Please ensure that all loads are evenly distributed and the center of gravity is kept as low as possible. Securing Long Loads: Long loads must be securely tied down to both the front and rear of the vehicle, in addition to the rack. Use only non-stretch fastening ropes or straps. CAUTION! TMT products should be used safely. The user must understand the precautions. Be smart, use good judgement. Failure to do so can result in ruined car, material damage, personal injury or even death.
5 05 ASSEMBLED VIEW PACKING LIST ITEM DESCRIPTION QTY. 1 Side Beam Crossbar 4 3 Wind Deflector 1 4 Deflector Support 2 5 Carriage Bolt (5/16 ) 6 6 Hex Nut (5/16 ) 6 7 Allen Bolt (M8) 20 8 Lock Nut (M8) Plain Washer (5/16 & M8) Hex Bolt (M6) Lock Washer (M6) Plain Washer (M6) Aluminum Spacer
6 06 INSTRUCTIONS REQUIRED TOOLS IMPORTANT TO OBSERVE! M10 and M13 Wrenches M6 Allen Key Slotted Screwdriver Utility Knife Silicon Sealant Lock Nuts are for the Allen Bolts and Standard Nuts are for the Carriage Bolts (Don t Included in Kit) The rack mounting points need Flat and Safety Washers 01 Locate both rubbers along either side of the roof ditchs. Using a Flat Screwdriver, start by lifting up from the windshield. Remove the rubbers pulling them firmly.
7 07 02 Locate and remove the 6 tapes in the gutters (3 on each side). Under the tapes you will find 10 threaded holes. So, you have 2 frontal, 1 center and 2 rear anchorage points (on each side). 03 Important to prevent rainwater leaks. Apply abundant Silicone Sealant around the anchorage points. Place the 10 Aluminum Spacers centered over each mounting hole. Apply pressu re so that it s well sealed and fixed. Let dry the time recommended by the manufacturer of Sealer.
8 08 04 This step is optional Look for the rubbers you removed in step 1. Cut the pieces that interferes with the Aluminum Spacers. Put them back on roof channels. 05 Note that this is the frontal Crossbar. Use Standard Nuts. Insert the heads of 4 Carriage Bolts through one Crossbar inferior rails. Couple the Deflector Supports as shown in the picture. Don t tighten up yet! Allows Supports to move sideways.
9 09 06 Apply a Max Torque of 30 lbf*ft to avoid damaging the thread. Connect the Crossbars to the Side Beams. Place them in the desired positions. Should be separated from each other as much as possible. Then tighten them in even increments. F R O N T A L 07 Use Lock Nuts. Place the Wind Deflector in position. Verify that it is centered and leveled. Screw it to the Side Beams.
10 10 08 Observe that the Deflector has two small square holes. Use Standard Nuts. Move the Deflector Supports sideways to align them with their frontal holes. Insert the Carriage Bolts through the Deflector holes with their nuts. Tighten all the nuts (Crossbar to Supports and Supports to Deflector). 09 Be careful. Avoid any contact between the rack and the roof antenna! Lift the rack between four people. Each one carrying a corner. From back to front, mount the rack on truck s roof. Rest the Side Beams Bases on the Aluminum Spacers.
11 11 10 Use the M10 Wrench. Insert the 10 roof s Bolts with its Plain and Lock Washers. Center and align the rack with respect to the truck. Tighten all screws and verify that rack is well fixed. TEST IT IN A SHORT JOURNEY! BEFORE FIRST RIDE! Make sure your rack is securely fastened to all mounting points. Verify that the Rack is centered, level and in desired position. If necessary, correct the clearance between Wind Deflector and roof. - Firstly, take a short ride to test your rack in safe conditions. - Pay attention for unusual noises or vibrations generated by the Rack. - Check again the fastenings. If anything is loose, RE- TIGHTEN!
12 12 PAINTING MAINTENANCE RECOMMENDATIONS With the objective of guaranteeing the best quality and durability of your painting, the products from TMT4x4 Accessories go through a rigorous quality control process. Among the processes that each of our products go through you find: chemical treatment, sand blasting and 4 layers of powder coating. Since we want you to have the best off-road experience with our products, we provide some recommendations for keeping them in the best possible way: - Maintain your vehicle clean, wash it with water and soap immediately after exposing to salty environments. The salt and magnesium chloride used on icy roads to prevent freezing is also there at the beach and in locations near the ocean, these are highly corrosive elements that will deteriorate your painting in time. - Avoid any drilling, cutting or modifications to your products because you will be creating spots where the oxidation process may begin. Remember that TMT4x4 have a wide range of accessories that adapt to your needs. If you find any damage in your painting or oxide spots, retouch it and make it as good as new: 1. Clean the area properly, remove all the oxide and damaged painting. 2. Sand the borders between the original painting and the metal until achieving a smooth transition. 3. Slowly apply several thin layers of Rust-Oleum spray painting of a similar color and texture to the original in your product until achieving the same thickness of the original painting. 4. If you use too much painting you can create ripples. Use sandpaper to reduce them and smoothen the surface. Once you see the repaired area is fairly similar to the original painting and that there are no abrupt changes, you have finished the job.
13 13 WARRANTY POLICY 1. Once you receive your TMT4x4 Accessories you have a 1-month warranty, due to defect or for replacing any of its components. 2. To make use of your warranty you must have your purchase order receipt that will arrive with your product; there you will find the order number that you can use to contact us directly through any of the following ways: Sales@TMT4x4.com Phone: Website: 3. At TMT4x4 we offer a material fatigue warranty on all of our accessories. 4. If you have any complaint due to change or defect in any product or one of its parts, it is required that you send the product back to us for replacement. The shipping cost for sending the product to the company will be paid by the client. 5. If you are not satisfied with the product, TMT4x4 Accessories will take returns, once we receive the product you will receive the amount for the original pricing. 6. TMT4x4 Accessories is not responsible for custom expenses for shipping to any destination, the client is responsible for this payment. 7. TMT4x4 Accessories is not responsible for any defects on the painting caused by scratches, impacts and/or bumps during shipping. We use third parties for our shipping and they are not responsible for any damages caused. We protect your purchase from any inconvenient and work hard to have your product delivered in the best possible conditions. 8. Warranty is lost on any of the following cases: - Damage caused by poor execution when installing on your vehicle. - Installation on non-compatible vehicles. - Overloading beyond the recommended capacity. - Damage caused by improper maintenance. - Improper use or damage received in competitions or races. - Ignoring the recommendations provided by the company. TMT4X4 ACCESSORIES IS NOT RESPONSIBLE FOR ANY PERSONAL OR MATERIAL AND/OR COMMERCIAL DAMAGE THAT MAY COME FROM USING THE ACCESSORIES
WARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Instructions
More informationMaximum load carrying capacity: 100kg / 220lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check the contents
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm Socket Hack Saw
More informationHaul-Your-Might T3. Product Name: Product Code: Please read all instructions carefully before assembly, installation and/or use of this product.
WARNING: DO NOT exceed 800 lbs. (363 Kgs) WARNING: DO NOT exceed vehicle manufacturer s weight rating. Haul-Your-Might T3 Tools Required: 17mm Socket 5mm Hex Key 1/8 Hex Key Tape Measure 17mm Wrench 13mm
More informationMitsubishi Triton Backbone RMTB1
Layout Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct location. Check
More informationToyota FJ Cruiser Backbone RFJB1
Toyota FJ Cruiser Backbone RFJB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the
More informationChannel Mount Generic Instructions (RDM01).
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationToyota 4Runner Track Mount Kit (RTS545)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Roof Rack System is installed in the correct location. Check the
More informationToyota Fortuner GLX/GX & Crusade Backbone - RTFB1
Toyota Fortuner GLX/GX & Crusade Backbone - RTFB1 Fit time: 1.5 hours Note: OEM roof rails removed. IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo
More informationInstallation Instructions Road Defender Push Bumper Part # L Ford Sedan Police Interceptor
Installation Instructions Road Defender Push Bumper Part # 5039-2L51 2013-2015 Ford Sedan Police Interceptor Do not attempt to install this product on any vehicle other than the one listed above! Parts
More informationK327W. Fitting Kit. Fitting Instructions for Basic Carrier. x 4 x 4 x 4 x 4. Revision No: 5E 1
Fitting Kit Fitting Instructions for Basic Carrier x 4 x 4 x 4 x 4 Revision No: 5E 1 Items you will require: Attention: First Time Installation Tape measure Pen Cordless drill Depth stop Vacuum cleaner
More informationRTS536 Toyota Prado 150 Track Mount
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the track mount system is installed in the correct location. Check the
More informationToyota 4Runner Backbone - RT4B1
Fit Time: 1 Hour Important Information Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 42102B 69kg / 152lb 49kg
More informationRhino Track Mount System
Tools required, Track install: Power drill Drill stop 5mm (3/6 ) drill bit Vacuum Cleaner Felt tip pen Carton knife Rivet gun/pneumatic Measuring tape Masking tape Automotive Butyl Sealant Caulking gun
More informationNM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System
NM-NP Pajero Rhino Heavy Duty - Two Bar Trackmount System Parts List Important: Care Instruction: Clean vehicle roof prior to fi tting Rhino Heavy Duty roof racks. Tools Required: Pneumatic or concertina
More informationRTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1.
RTS518 - Rhino Heavy Duty 2 & 3 Crossbar System Hyundai iload, imax, i800, H-1. NOTE: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment
More informationRLCP27 Rhino Crossbar System Jeep Grand Cherokee
RLCP27 Rhino Crossbar System Jeep Grand Cherokee Maximum roof load: 68kg/149lbs Refer to vehicle manufacturers handbook for maximum roof loading. Always use lower of the two figures. Recommendations: It
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING!! ü! ü! km/h X 2 x Crossbars = 5kg? kg WARNING! Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
CONTROLLED Pioneer Tray, Pioneer Platform & Pioneer Tradie Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior
More informationWARNING! 2 x Crossbars = 5kg
WARNING!! ü!! km/h 2 x Crossbars = 5kg? kg - Please refer to your vehicle manufacturers handbook for maximum roof load capacity. - Any load transported on Roof Racks must be evenly distributed. - Do not
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationToyota Hilux Track Mount (RTS543)
Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing fi tment and report any discrepancies. Place these instructions in the vehicle
More informationRTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK
RTS510 Rhino Heavy Duty Track Mount System - MITSUBISHI TRITON MK Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationNissan Patrol Y62 RNPB1
Nissan Patrol Y62 RNPB1 Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the Backbone System is installed in the correct
More informationRTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails -
RTS524 MITSUBISHI Challenger - Two Cross Bar Track Mount System - With or without roof rails - Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction
More informationRhino-Rack Kayak T-Load 2 Hitch Mount (RTL002)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD SILVERADO 1500 PART #
INSTALLATION INSTRUCTIONS PART # 3-5863 4-0863 PARTS LIST: Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm Hex Bolts 1 Driver/Left Mounting
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
6065 SUBKIT 7/7/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-50, F-50 PAGE OF WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE FOR
More informationInternational Scout Traveler Installation Instructions
International Scout Traveler Installation Instructions Tools needed: 9/64 drill bit 1/8 drill bit #2 Philips bit for drill Tape measure Pencil Drill #3 Philips Screwdriver #2 Philips Screwdriver Utility
More informationPioneer Tray, Pioneer Platform & Pioneer Tradie
Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the contents of this kit before commencing
More informationXTray Small (RMCB01)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the XTray is installed in the correct locations. Check the contents of
More informationWARNING! 2 x Crossbars = 5kg. ? kg
WARNING ü ü km/h X 2 x Crossbars = 5kg? kg WARNING Important Load Carrying Instructions With utility vehicles, the cabin and the canopy move independently. Roofracks and vehicle can be damaged if the item
More informationJeep Wrangler JK SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount
Jeep Wrangler JK 2011- SG59 4dr & SG60 2dr- Rhino Sportz Gutter Mount Important: Please read these instructions carefully prior to installation. Check the contents of kit before commencing fitment and
More informationLandrover Discovery 3 - Rhino Tracks.
Parts List Important: Landrover Discovery 3 - Rhino Tracks. Place these instructions in the vehicle s glove box after installation is complete. Please read these instructions carefully prior to installation.
More informationRLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System.
RLCP17 Rhino Heavy Duty Toyota landcruiser 200 Series Three Crossbar System Place these instructions in vehicle s glovebox after installation is complete Important: Please read these instructions carefully
More informationPermanent Mount Rack with Hidden Hardware Installation Instructions
Permanent Mount Rack with Hidden Hardware Installation Instructions Package Contents: 8 - Permanent Mounting Bracket 8 - U-Clips 8-1/4-20 x 1-1/4" Carriage Bolts 8-1/4-20 Nuts with Integral Lock Washer
More informationRhino-Rack Toyota Prado 3 Bar Heavy Duty System (RLCP23)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the racks are installed in the correct locations. Check the contents of
More informationCare Instruction: Wash vehicle roof prior to installing Rhino Tracks.
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationToyota Kluger/Highlander SUV XU50 RLCP37
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationRhino Pioneer SXB (44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete.
(44100B, 44101B, 44102B & 44103B) Place these instructions in the vehicle s glove box after installation is complete. Important: Please read these instructions carefully prior to installation. Check the
More informationFIRST TIME INSTALLATION
LOCKN LOAD TM PLATFORM MAX PLATFORM LOAD RATING: 100 KG (sizes A, B, F, G, I, K, & L) 150 KG (sizes C, D, E, H, J, N, P & U) PLEASE REFER TO VEHICLE MANUFACTURER SPECIFICATIONS FOR MAX ROOF LOAD RATING
More informationImportant Information
Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fi tment and report any discrepancies. Clean roof prior to installation.
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD GMC SIERRA 1500 EXCLUDES DENALI PART # 4084/
INSTALLATION INSTRUCTIONS GRILLE GUARD 14-15 GMC SIERRA 1500 PART # 4084/ 4084-2 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350
60647 SUBKIT 7/3/204 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** FORD F-250, F-350 PAGE OF 4 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED TO PROVIDE CLEARANCE
More informationRTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System
RTS528 - Holden Colorado/ Isuzu D-MAX Space Cab Track Mount System Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More information06-08 Passenger/Right Top Mounting Bracket Driver/Left Top. Mounting Bracket. Driver/Left Frame Mounting Bracket
PARTS LIST: 1 Grille Guard 4 12mm x 44mm OD x 3mm Flat Washers 1 Driver/Left Frame Mounting Bracket 12 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Frame Mounting Bracket 4 12mm Lock Washers 1 Driver/Left
More informationAND LOAD LADDER CARRIER FOR TRANSIT CONNECT SPECIFICATIONS
8MAY15 INSTRUCTIONS for the LOCK AND LOAD LADDER CARRIER FOR TRANSIT CONNECT SPECIFICATIONS and SAFE LOADING REQUIREMENTS The Lock and Load Ladder Carrier for the Transit Connect is a rack designed to
More informationRSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee
RSP27 Rhino Sportz Two Crossbar System Jeep Grand Cherokee Important: Please read these instructions prior to installation. Check contents of kit before commencing fitment and report any discrepancies.
More informationK1013 K1013. Fitting Instructions for Basic Carrier. x 4 x 4 x 1 x 8. x 4 x 1 x 4 x 1. x 4 x 1 x 1 x 2. Revision No: 1A 1
Fitting Instructions for Basic Carrier x 4 x 4 x 1 x 8 x 4 x 1 x 4 x 1 x 4 x 1 x 1 x 2 Revision No: 1A 1 MAX kgs (lbs) W/P WHD Holden Spark, 5dr Hatch 16-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs) Spark, 5dr
More informationPassenger/Right Side Frame Bracket. Driver/Left Side Frame Bracket. (4) Spacer Washers. (2) Bull Bar Mounting Brackets
PARTS LIST: 1 Bull Bar 12 s 1 Driver/Left Frame Mounting Bracket 1 Passenger/Right Frame Mounting Bracket 6 10mm Lock Washers 2 Bull Bar Mounting Brackets 6 10mm Hex Nuts 4 Large Spacer Washers 4 8-1.25mm
More informationFlexiglass - FlexiXover Canopy RTCFG02 RTCFG03
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Canopy Rack System is installed in the correct location. Check the
More information(W) INSTALLATION INSTRUCTIONS GRILLE GUARD 2014 GMC SIERRA 1500 EXCLUDES DENALI PART # /
(W) INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 508514/ 508515 PARTS LIST: GRILLE GUARD Qty Description Qty Description 1 Grille Guard Assembly 6 12-1.75mm Hex Nuts 2 Frame Brackets 4 10-1.50mm x 30mm
More informationRSP17 Rhino Toyota landcruiser 200 series Three Crossbar System.
Parts List RSP17 Rhino Toyota landcruiser 200 series Three Crossbar System. Place these instructions in vehicle s glovebox after installation is complete. Important: Please read these instructions carefully
More informationtiltaway Bike Carrier Assembly Instructions
tiltaway Bike Carrier Assembly Instructions Version 150301 To ensure the best service and satisfaction from your Advantage SportsRack tiltaway, please read and follow all instructions, recommendations,
More informationToyota Kluger RSP31. Maximum load carrying capacity: 80kg / 176lbs. Important Information. 1. Check Part No./Kit is correct 3. Fit roof rack accessory
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the correct location. Check the contents
More informationToyota Prado 150 Backbone - RTPB1
Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Suitable On Road Cargo Off Road Cargo Pioneers On Road & Off Road Cargo Allowance Pioneers Allowance Allowance Static
More informationJeep JK 2dr Backbone - RJKB2
Fit Time: 1.5 Hours IMPORTANT INFORMATION Maximum carrying capacity: On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance Rack Weight 95kg / 209lbs 63kg / 138lbs 240kg / 530lbs
More informationINSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: Application: Toyota Tacoma
INSTALLATION INSTRUCTIONS SEMI Hidden Kit Part Number: 100044 Application: 2016+ Toyota Tacoma GENERAL SAFETY PRECAUTIONS Your safety, and the safety of others, is very important. To help you make informed
More informationCognito Motorsports 2014 Polaris RZR XP1000 2/4 seat Tie Rod Kit *Installation Instructions*
Cognito Motorsports 2014 Polaris RZR XP1000 2/4 seat Tie Rod Kit *Installation Instructions* For long travel and stock width kit #s: 360-90021 and 360-90060 Introduction - Installation requires a qualified
More informationRLT500 - Rhino Track Leg Kit
- Rhino Track Leg Kit Maximum carrying capacity: 100kg/220lbs evenly distributed over the crossbars. Please refer to your vehicle manufacturers handbook for maximum roof loading. Always use lower of these
More informationToyota Prado 120 Backbone - RTPB2
Toyota Prado 120 Backbone - RTPB2 Fit Time: 1.5 Hours Layout: IMPORTANT INFORMATION Maximum carrying capacity: Suitable Pioneers On Road Cargo Allowance Off Road Cargo Allowance Static Allowance Roof Allowance
More information#1034 Ford Sport Trac Installation Instructions
#1034 Ford Sport Trac Installation Instructions Owner s Manual Please save Instructions: Important Warranty and Maintenance information enclosed (2) 10-24 Black flathead Allen Screws Tailgate End Front
More informationEZ Carrier 3. Owner s Manual. Keep instructions for future reference
EZ Carrier vv Owner s Manual Keep instructions for future reference Introduction The EZ Carrier provides all the flexibility you may need to transport your mobility scooter. The features include: The capability
More informationRhino Tourmaster Alloy Tray (RTAT)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the roof racks are installed in the correct locations. Check the contents
More informationHyundai i30 & i40 Tourer RLCP40, RSP40/41
Hyundai i30 & i40 Tourer RLCP40, RSP40/41 Important Information Maximum roof load: 75kg/165lbs evenly distributed across two crossbars. Refer to vehicle owners manual for maximum roof loading. Always use
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More information**DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!**
60660 SUBKIT 7/8/0 **DO NOT EXCEED RECOMMENDED VEHICLE TOWING WEIGHT!** DODGE 500 / 3500 SHORT AND LONG BED PAGE OF 5 WARNING!! BRAKE, FUEL, AND ELECTRICAL LINES MAY NEED TO BE LOOSENED OR REPOSITIONED
More informationRace Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE
Race Sport Lighting RSUKIT LED UNDERBODY KIT INSTALLATION GUIDE PARTS LIST (INCLUDED IN THE KIT) 1 x LED Control Center Box 2 x 48 RGB Aluminum Channel LED Bars 2 x 36 RGB Aluminum Channel LED Bars 1 x
More informationRhino-Rack Nautic Kayak Loader (NKL)
Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. heck the contents
More informationInstallation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT
www.riderite.com 4111 / 4118 4150 / 4156 4164 / 4182 4188 Installation Instructions READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT VEHICLE PREPARATION With the vehicle
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationPARTS LIST: PROCEDURE:
PARTS LIST: EVO3 LIGHT BAR Qty Description Qty Description 1 EVO3 Light Bar 2 10mm U-Bolt (for use on "closed frames" only) 1 Light Mount Crossbar Bracket 4 10mm x 26mm OD x 3mm Flat Washers 2 Light Tab
More informationRhino Ski/ Snowboard Carrier 572, 573, 574, 576
Rhino Ski/ Snowboard Carrier 572, 573, 574, 576! Important: Please refer to your fi tting instruction to ensure that the roof racks are installed in the correct locations. Check the contents of kit before
More informationQ20. Track System. Fitting Instructions for Basic Carrier. x 2 x 2 x 2 x 1. x 1 x 1 x 4 x 4. Revision No: 1A 1
Track System Fitting Instructions for Basic Carrier x 2 x 2 x 2 x 1 x 1 x 1 x 4 x 4 Revision No: 1A 1 x 4 x 1 x 20 x 20 x 20 2 First Time Installation Remove parts from inside the package and check. Contact
More informationB C A. EN bike trays with ratchet arms 2. EN front wheel holder 2. EN rear wheel holder assembly 2. EN 4mm self tapping screw 10
T2 PRO 9036 2 BIKE ADD-ON FOR (2" HITCH) = North American English PARTS INCLUDED B C A D A E F G H I J K L M N part description qty. A add-on mast 1 B bike trays with ratchet arms 2 C front wheel holder
More informationWildcat System Instructions
Wildcat System Instructions NOTE: Most steps contained in these instructions will need to be repeated on the other side of the vehicle. Prior to assembly of windshield it is necessary to establish what
More informationInstallation Instructions
1501100 Ladder Rack Installation Instructions Before Assembling: Before assembling your Buyers ladder rack it s important to read, understand, and follow all listed instructions. Note: There are two different
More informationRTS538 ISUZU MU-X LS-T Trackmount
Please read these instructions carefully prior to installation. Check the contents of kit before commencing fi tment and report any discrepancies. Please refer to your fi tting instruction to ensure that
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationHP10171 KIT. Chevy/GMC Pick-Up Trucks 2500/3500* 2WD/4WD with or without 5 th Wheel Hitch
HP10171 KIT Chevy/GMC Pick-Up Trucks 2500/500* 2WD/4WD with or without 5 th Wheel Hitch * See application guide for proper fitment. Use the strongest air springs on the market to eliminate your vehicle
More informationRLCP08R- Rear Crossbar
- Rear Crossbar VOLKSWAGEN Caddy Maxi MY11> RENAULT Kangoo Maxi MY13> Important: Please read these instructions carefully prior to and during installation. Check the contents of kit before commencing fitment
More informationWWW. MOOSERACING.COM 1 / 8. INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE [KTM 1190 Adventure 2014 & up]
E x p e d i t i o n L u g g a g e Adventure Pannier Mount Set INCLUDES EVERYTHING YOU NEED TO ADD MOUNTS TO YOUR MOTORCYCLE 3501-0920 [KTM 1190 Adventure 2014 & up] Features of the Expedition Luggage -
More information/ GMC SIERRA 2500 / 3500 START HERE BEFORE YOU BEGIN STEP 2
2015-2016 CHEVROLET SILVERADO 2500 / 3500 / 2015-2016 GMC SIERRA 2500 / 3500 Z321221 / Z321221-KIT FRONT BUMPER LED LIGHT MOUNTS Parts included - (1) Driver Side Light Mount Bumper Bracket - (1) Passenger
More informationOPERATING INSTRUCTIONS AND TROUBLE SHOOTING GUIDE
OPERATING INSTRUCTIONS AND TROUBLE SHOOTING GUIDE Thank you for purchasing Driverite-Firestone Air Suspension System. You have purchased a quality product from the world s number one Air Spring Manufacturer.
More informationLINDGREN-PITMAN General Maintenance of Lindgren-Pitman Hydraulic Systems & Equipment
LINDGREN-PITMAN General Maintenance of Lindgren-Pitman Hydraulic Systems & Equipment Page 1 Lindgren Pitman hydraulic driven equipment is designed to give long reliable service with a minimum of repairs
More information1st Generation K5 Blazer (1969 to 1972)
1st Generation K5 Blazer (1969 to 1972) Tools needed: 9/64 drill bit Tape measure Pencil Drill Wrenches Screwdrivers Contents: 2 - bedrails (2 pieces each) 2 - folding frame uprights 1 header bar 3 - cross-bows
More informationRhino-Rack 2 Hitch Receiver Bike Carrier (4 Bikes)
Important: Please read these instructions carefully prior to installation. Please refer to your fitting instruction to ensure that the bike rack is installed in the correct locations. Check the contents
More information4101 / 4102 READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT PARTS LIST OPERATING PRESSURES. Figure A DESCRIPTION
4101 / 4102 READ INSTALLATION INSTRUCTIONS IN ITS ENTIRETY BEFORE INSTALLING YOUR COIL-RITE KIT Figure A PARTS LIST DESCRIPTION QTY. AIR SPRINGS 2 UPPER SUPPORTS 2 LOWER SUPPORTS (BOLT) 2 LOWER SUPPORTS
More informationINSTALLATION INSTRUCTIONS DRAWERS #240
INSTALLATION INSTRUCTIONS DRAWERS #240 Please read and fill out the enclosed warranty registration card to activate your warranty. SHIPMENT CONTENTS #1 Lid #2 Rear #3 Left side panel #4 Right side panel
More information3" SIDEBARS BODY BOLT MOUNT SILVERADO/SIERRA CREW CAB (Excl. C/K Classic )
(W) INSTALLATION INSTRUCTIONS 2001-2015 CHEVY SILVERADO/GMC SIERRA 1500/2500/3500 MODELS (body mount) CREW CAB PART # DZ 371531;DZ 371533;DZ 372531;DZ 372533; DZ 372531HD; DZ 372533HD Page 1 of 6 IMPORTANT
More informationINSTALLATION INSTRUCTION BULL BAR DODGE RAM 1500 PART NUMBER
INSTALLATION INSTRUCTION 09-12 DODGE RAM 1500 PART NUMBER - 200691 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Mounting Brackets (for trucks without tow hooks
More information31075 INSTALLATION INSTRUCTIONS
075 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 06-PRESENT MAKE: TOYOTA MODEL: TACOMA STYLE: PICKUP WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S
More informationSwitchback Carrier Rack System
Switchback Carrier Rack System Installation Instructions 1 Rocky Mountain Westy Ph. (970)310-3441 Introduction Thank you for purchasing the Rocky Mountain Westy Switchback Carrier Rack System. We pride
More informationRhino-Rack Kayak T-Load Tow Ball Mount (RTL001)
CONTROLLED Rhino-Rack Kayak T-Load Tow Ball Mount (RTL001) Important: Please read these instructions carefully prior to installation. Please refer to your fi tting instruction to ensure that the roof racks
More informationPage 1. File: Motolight caliper one-piece Harley Date: 8/15/2006
Page 1 Harley-Davidson FL Caliper Mount Installation One-piece mounting brackets You should allow about two to three hours for installation. We suggest you use a well-lighted space for installation. PLEASE
More informationWARNING OPERATING PRESSURES: READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING YOUR KIT
4190 www.riderite.com OPERATING PRESSURES: MINIMUM (UNLOADED) MAX (LOADED) 5 PSI 35 PSI READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING YOUR KIT INSTALLATION INSTRUCTIONS Congratulations your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HDX LED GRILLE APPLICATION: 2019 Ram 1500 (Excl. Classic) PART NUMBER: 34-1145 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 GRILLE 10MM WRENCH 2 2 LED LIGHT HOUSING RATCHET
More information