Lubrication Equipment

Size: px

Start display at page:

Download "Lubrication Equipment"

Buddy Owens
5 years ago
Views:

1 IVISION Lubrication Equipment utomatic lubricators

UTOMTI LURITORS FOR OIL N OTHER FLUIS RIP FEE OILERS rip feed oilers are designed to dispense oil or other fluids into one or more lubricating points.

positions in which they are shown in the following figures.

regards drip feed oilers for more lubricating points, these are located at the bottom of individual drippers).

The reservoirs can be made of plexiglas or ; both materials allow for the visual monitoring of the liquid level.

If oil needs to be spread onto a surface (e.g. chain lubrication), the oil output point will be provided with a lubricating brush.

, and others) allow for the automatic linkage of the dispensing of the lubricant to the operating hours of the machine being lubricated.

Note: if oil is used, 1 ml equals approximately 45 drops. RIP FEE OILER, TYPE UNI For connection to a single lubricating point, with manual valve.

Material: pickled brass, or, sealing Perbunan (NR) / material of the reservoir 22 25 2 2 UNI 25 UNI 0 10 20 72 77 imensions [ml] ø 2 21 UNI 40 6 40 40 10 21 2 UNI 4 12 212

214 UNI 10x1 2 000 R 1/2"(a) R 1/4"(i) 240 1 10 16 226 216 UNI 1x10 000 R 1/2"(a) R 1/4"(i) 270 10 1 16 2 0 25 0 Upon request, selected drip feed oilers of this type are also

2 UTOMTI LURITORS FOR OIL N OTHER FLUIS RIP FEE OILERS rip feed oilers are designed to dispense oil or other fluids into one or more lubricating points. Their function is only gravitybased, i.e. they are not capable of exerting any pressure and need to be positioned above the level of the lubricating point, but only in the positions in which they are shown in the following figures. For all types of drip feed oilers, it is possible to visually check the release of individual drops through a control window located at the bottom of the lubricator (as regards drip feed oilers for more lubricating points, these are located at the bottom of individual drippers). rip lubricators are fitted with seals made of Perbunan (NR); upon request Viton (FKM) or Teflon (PTFE) seals are available. The reservoirs can be made of plexiglas or ; both materials allow for the visual monitoring of the liquid level. The outputs from the drip lubricator are connected to the lubricating point either directly or through a short distribution line (plastic pipe, fittings, anchoring material). If oil needs to be spread onto a surface (e.g. chain lubrication), the oil output point will be provided with a lubricating brush. wide range of lubricating brushes and accessories for them can be found in Lubricating brushes catalogue pages. rip feed oilers with an electromagnetic valve (types ELO, MET., and others) allow for the automatic linkage of the dispensing of the lubricant to the operating hours of the machine being lubricated. lternatively, it is possible to install a TUP 1071 timer (optional) on the connector of this electromagnetic valve, on which further cycling can be set as needed. Note: if oil is used, 1 ml equals approximately 45 drops. RIP FEE OILER, TYPE UNI For connection to a single lubricating point, with manual valve. The frequency with which individual drops are dispensed can be regulated manually, or completely closed using a mechanism located above the reservoir. Material: pickled brass, or, sealing Perbunan (NR) / material of the reservoir UNI 25 UNI imensions [ml] ø 2 21 UNI UNI UNI UNI x UNI 0x 0 R 1/2"(a) R 1/4"(i) UNI x 7 R 1/2"(a) R 1/4"(i) UNI x R 1/2"(a) R 1/4"(i) UNI 10x R 1/2"(a) R 1/4"(i) UNI 1x R 1/2"(a) R 1/4"(i) Upon request, selected drip feed oilers of this type are also available with other thread sizes, and possibly also with a lowlevel magnetic switch RIP FEE OILER, TYPE TOL For connection to a single lubricating point, with manual valve. The frequency with which individual drops are dispensed can be regulated manually, or completely closed using a mechanism located bellow the reservoir. Material: nickelplated brass, or, sealing Perbunan (NR) / material of the reservoir imensions TOL 25 TOL 0 [ml] ø TOL TOL TOL TOL x Upon request, selected drip feed oilers of this type are also available with other thread sizes

Other types of drip feed oilers for connection to a single lubricating point, with a manual valve (upon request): RIP FEE

capacities: 20, 5, 70, 125, 200, a 4 ml Material: pickled brass, /, sealing Perbunan (NR) capacities: 20, 5, 4, 0, 200, 0 a 1

connection to more lubricating points, with a manual valve.

The selected designs need to be complemented with the corresponding number of additional drippers, so that drip lubricators

The frequency with which individual drops are dispensed can be manually regulated for each lubricating point separately, or

drip feed oiler of this type also includes a manual valve for the closing of the oil supply to all drippers at once.

ø 2 216 MTM.2 0 0 1 212 21612 MTM.2 200 200 10 0 21 2161 MTM.2 0 0 220 0 2 216 MTM.2 1 000 1 000 2 2 216 MTM.

2 000 000 5 10 1 escription 2241 dditional dripper with a control window (an extra lubricating point) 2242 dditional dripper

available with other thread sizes, and possibly also with a lowlevel magnetic switch RIP FEE OILER, TYPE ELO For the

The frequency with which individual drops are dispensed can be manually regulated, or completely closed using a mechnism

This type of drip feed oiler also contains an electromagnetic valve, which can be used to open/close the oil supply from the

connection : 20 V (24 V at ELO 40), IP20 *) Material: nickelplated brass, or, sealing Perbunan (NR) / material of reservoir

3 Other types of drip feed oilers for connection to a single lubricating point, with a manual valve (upon request): RIP FEE OILER, TYPE UNIV RIP FEE OILER, TYPE UST RIP FEE OILER, TYPE KPO Material: pickled brass, /, sealing Perbunan (NR) capacities: 20, 5, 70, 125, 200, a 4 ml Material: pickled brass, /, sealing Perbunan (NR) capacities: 20, 5, 4, 0, 200, 0 a ml Material: nickelplated brass, /, sealing Perbunan (NR) capacities: 200, 0 a ml RIP FEE OILER, TYPE MTM For connection to more lubricating points, with a manual valve. ll the designs mentioned bellow comprise two drippers (for two lubricating points). The selected designs need to be complemented with the corresponding number of additional drippers, so that drip lubricators include as many drippers as there are lubricating points (up to a maximum of 10). The frequency with which individual drops are dispensed can be manually regulated for each lubricating point separately, or completely closed using a mechanism located at individual drippers. drip feed oiler of this type also includes a manual valve for the closing of the oil supply to all drippers at once. Material: nickelplated brass, pickled brass (drippers), or, sealing Perbunan (NR) / material of the reservoir imensions [ml] ø MTM MTM MTM MTM MTM MTM escription 2241 dditional dripper with a control window (an extra lubricating point) 2242 dditional dripper with a control window (an extra lubricating point) R /" Upon request, selected drip feed oilers of this type are also available with other thread sizes, and possibly also with a lowlevel magnetic switch RIP FEE OILER, TYPE ELO For the connection to a single lubricating point, with an electromagnetic valve. The frequency with which individual drops are dispensed can be manually regulated, or completely closed using a mechnism located above the reservoir. This type of drip feed oiler also contains an electromagnetic valve, which can be used to open/close the oil supply from the lubricator (relationship to the operating hours of the lubricating point). El. connection : 20 V (24 V at ELO 40), IP20 *) Material: nickelplated brass, or, sealing Perbunan (NR) / material of reservoir imensions [ml] ø ELO ELO 0 0 R 1/2"(a) R 1/4"(i) ELO R 1/2"(a) R 1/4"(i) ELO 0 0 R 1/2"(a) R 1/4"(i) ELO R 1/2"(a) R 1/4"(i) ELO R 1/2"(a) R 1/4"(i) ELO R 1/2"(a) R 1/4"(i) *) Upon request, drip feed oilers of this type are available with a type H electromagnetic valve with IP65 protection (for wet and dusty enviroments) and also in a design for explosive enviroments (EXdesign) Upon request, selected drip feed oilers of this type are also available for the voltages of 24 V /, 4 V, and V, and possibly also with a lowlevel magnetic switch

RIP FEE OILER, TYPE MET. For connection to more lubricating points, with an electromagnetic valve. ll the designs mentioned below comprise two drippers (for two lubricating points).

of 10). The frequency with which individual drops are dispensed can be manually regulated for each lubricating point separately, or completely closed using a mechanism located at individual drippers.

El. connection: 20 V, IP20 *) Material: nickelplated brass, pickled brass (drippers), or, sealing Perbunan (NR) / reservoir material imensions [ml] ø 22421 2241 MET.

.2 000 200 0 1 000 2 000 000 195 25 275 20 0 1 10 0 1 1 escription 2241 dditional dripper with a control window (an extra lubricating point) 2242 dditional dripper with a control window (an extra

for explosive enviroments (EXdesign) Upon request, selected drip feed oilers of this type are also available for the voltages of 24 V /, 4 V, and V, and possibly also with a lowlevel magnetic switch

They are suitable for lubricating points with a lower lubricant consumption and low backpressure. They are often used to lubricate points that are not easily accessible.

4 RIP FEE OILER, TYPE MET. For connection to more lubricating points, with an electromagnetic valve. ll the designs mentioned below comprise two drippers (for two lubricating points). The selected designs need to be complemented with the corresponding number of additional drippers, so that drip lubricators include as many drippers as there are lubricating points (up to a maximum of 10). The frequency with which individual drops are dispensed can be manually regulated for each lubricating point separately, or completely closed using a mechanism located at individual drippers. The drip lubricator of this type also includes an electromagnetic valve for the closing of the oil supply to all drippers at once (relationship to the operating hours of the device being lubricated). El. connection: 20 V, IP20 *) Material: nickelplated brass, pickled brass (drippers), or, sealing Perbunan (NR) / reservoir material imensions [ml] ø MET MET MET..2 0 MET MET MET escription 2241 dditional dripper with a control window (an extra lubricating point) 2242 dditional dripper with a control window (an extra lubricating point) R /" 22 *) Upon request, drip feed oilers of this type are available with a type H electromagnetic valve with IP65 protection (for wet and dusty enviroments) and also in a design for explosive enviroments (EXdesign) Upon request, selected drip feed oilers of this type are also available for the voltages of 24 V /, 4 V, and V, and possibly also with a lowlevel magnetic switch UTOMTI SPRING GRESE LURITORS Spring grease lubricators are designed to dispense greases (up to NLGI 2) to a single lubricating point. They are suitable for lubricating points with a lower lubricant consumption and low backpressure. They are often used to lubricate points that are not easily accessible. Grease is pressed into the lubricating point under gentle pressure, provided by a spring located above a follower plate inside the reservoir. This lubricator can be situated in any position. Ideally, the lubricator can be connected directly to the thread of the lubricating point; in extreme cases, a short distribution pipeline can be installed between the output from the lubricator and the lubricating point (up to approx. 0,5 m is recommended). oth mentioned types of these lubricators can be refilled through a type H1 grease nipple. SPRING GRESE LURITOR, TYPE SK This type of lubricator is available in three designs:.2 Without the possibility of any regulation SK.2.1 With an adjustable amount supplied, with the use of a throttle valve SK.1.0 With an adjustable amount supplied, with the use of a throttle valve, and the possibility of opening/closing SK.0 Material: pickled brass, SK.2 SK.2 SK.1 SK.1 SK.0 SK.0 [cm ] ø imensions grease nipple H1 for filling

5 IVISION SPRING GRESE LURITOR, TYPE SS In this type of lubricator, in addition to the possibility of choosing the reservoir size (0 or ml), it is also possible to set the spring (, 5 or bar). The spring should be selected according to the backpressure at the lubricating point. Material: nickelplated steel grease nipple H1 for filling full 1 2 empty Spring setting [cm] [bar] 1 2 ø SS SS SS SS SS SS imensions 224 escription 40 Shutoff valve R 1/4"(i)/ for SS 0/ *) shutoff valve *) The shutoff valve is not part of the SS lubricator, and needs to be ordered separately UTOMTI LURITORS FOR GRESE N OIL TYPE SIMLUE ctivation screw with gas producing drycells SIMLUE automatic lubricators are designed to dispense greases (up to NLGI 2) and oils to a single lubricating point. They are suitable for lubricating points with a lower lubricant consumption and low backpressure. They are often used to lubricate points that are not easily accessible. The principle of the SIMLUE lubricator is based on a chemical reaction in which the solid substance in a cartridge inside the activation screw turns into gas that accumulates in a pressure chamber and pushes a piston, causing the lubricant to be forced under the piston from the lubricator in the direction of the lubricating points. The emptying time of the lubricator can be set to be between 1 month and 12 using an llen key directly on the activation screw, or it is possible to completely stop the dispensing of the lubricant (0). Thanks to the control window with a scale it is possible to check the amount of lubricant currently in the lubricator at any time. The lubricator can be situated in any position, and it is capable of working under water, too. Ideally, the lubricator can be connected directly to the thread of the lubricating point; in extreme cases, a short distribution pipeline can be installed between the output from the lubricator and the lubricating point (up to approx. 0,5 m is recommended). The lubricator can be repeatedly refilled through a filling connection (see accessories) or a filling pump. fter refilling it is always necessary to replace the activation screw with a new one (see accessories). Range of operating temeratures: 20 až SL SL SL Inspection window Pressure chamber Transparent housing Piston Label Lubricant Funnel Filling ø empty empty multipurpose grease 62 SL multipurpose grease 2712 SL chain oil SL chain oil [ml] imensions Upon request, SIMLUE lubricators are also available with a reservoir volume of 0 ml or 2 ml, and wide range of filling (food industry greases and oils, biodegradable greases, high temperature greases and oils etc.) Sizes of SIMULUE lubricators (0,, 125 and 2 ml) ctivation screws with gas producing drycells Setting of volumes supplied Refilling with the use of a filling pump pplication example pplication example pplication example

6 IVISION ESSORIES OF SIMLUE LURITORS escription ctivation screw with gass producing drycell for SIMLUE ml, M 1x1,5(a) 2790 ctivation screw with gass producing drycell for SIMLUE 125 ml, M 1x1,5(a) Filling connection R 1/4"(i)(grease nipple H1) 279 lamp d mm Nonreturn valve d mm(a) plastic *) Nonreturn valve R 1/4"(i) nickelplated brass *) 27902, 2790 *) It is recommended to use a nonreturn valve whenever the SIMLUE lubricator is filled with oil STUFFER LURITOR This is not an automatic lubricator in the true sense. The Stauffer lubricator is permanently screwed to the lubricating point, the lubricant is caused to flow by pressure generated by rotation of the screwed lid of the reservoir. ccording to IN 4, form Material: blackened steel imensions SW ø M 10x1(a) 21 2, M 12x1,5(a) M 12x1,5(a) M 12x1,5(a) R /"(a) R /"(a) [cm] SW Upon request, Stauffer lubricators according to IN 4, form made of brass are available, with reservoirs with a volume from 0,6 to 10 cm sk for further details regarding other products of the LURITION EQUIPMENT group Grease nipples Grease guns and units utomatic lubricators Equipment for handling with lubricants and fuels Equipment for handling with used oil Lubricant distribution components Oil windows, breather plugs, lubrication brushes Visit our web sites: IVISION EMTEH, HENNLIH INUSTRIETEHNIK, spol. s r.o. Z Zdar nad Sazavou, Libusinska 1, tel.: , fax: , cematech@hennlich.cz HENNLIH INUSTRIETEHNIK, spol. s r.o. Z Litomerice, eskolipska 9, tel.: , fax: , EMTEH info /2009En

smart lubrication Single Point Lubricator The Compact and Refillable Single-Point Lubricator worldwide patents

smart lubrication Single Point Lubricator The Compact and Refillable Single-Point Lubricator worldwide patents simalube, the compact lubricator that is economical, universally adaptable, and a friend to