TPMS Adapter Instruction Manual. (Tire Pressure Monitoring System)

Transcription

1 TPMS Adapter Instruction Manual (Tire Pressure Monitoring System) Rev 1.1 BEFORE YOU START READ INSTRUCTIONS CAREFULLY BEFORE USE IF YOU HAVE ANY QUESTIONS ABOUT THE USE OF THIS DEVICE, CONTACT YOUR BIMMER RETROFIT REPRESENTATIVE BEFORE USE Installation of TPMS Adapter should be performed by an installer with appropriate knowledge and experience in BMW vehicle electronics. We strongly recommend using services of professional installers, experienced with BMWs, for this installation. Battery should be disconnected prior to the installation for safety reasons. Reconnection of the battery should be done only after all electrical connections are in place.

2 1. DEVICE OVERVIEW The main parts of the TPMS kit are: - TPMS Adapter module with built in ECU and RF receiver - Wheel sensors with ability to sense and transmit information about pressure and temperature for each individual wheel - Wiring loom to connect TPMS adapter to vehicle s wiring (cut and splice)

3 1. Micro USB port: On one side of the TPMS adapter s box, there is a Micro USB port, which can be used for firmware update of the TPMS Adapter. Please see appropriate section of this document for the instruction on how to complete the firmware update. IMPORTANT! Be careful when connecting or using USB plug to/with Micro USB port as excessive pressure on the connector will damage the port inside of the adapter and will make device unrepairable due to internal PCB traces damage. 2. Control Button: Button is used whenever manual firmware update is required. 3. TPMS Module Utility: can be used for configuration of the device including wheel sensors registration / de-registration, CAN bus speed configuration, etc. The TPMS Module Utility can be downloaded from here: 2. SOFTWARE SUPPORT All versions of the TPMS Adapter come with a free TPMS Module Utility, which can be downloaded on our website:

4 3. INSTALLATION INSTRUCTION FOR THE TPMS ADAPTER 1. Sensors come with the kit un-assembled in three parts: sensor, aluminum nipple and screw with holding spring. Each sensor needs to be assembled prior to the installation. This should be done at the garage by specialist with appropriate experience. 2. It is usually marked on each sensor to which particular wheel it should be installed: FL, FR, RR, RL 3. TPMS receiver module can be placed anywhere inside of the vehicle.

5 The following should be noted: TPMS receiver has built in RF receiver for communication with the sensors installed in the wheels. TPMS module should not be placed anywhere near large metal objects closer than 20cm or 8 inches. Module also should not be placed under the dashboard near the head unit closer than 10cm or 4 inches. The best location for the TPMS receiver is in the armrest compartment, under it or under the dashboard at its highest point. For example: TPMS receiver module can be mounted near gear shifter under the center tunnel plastic where idrive controller is located. 4. TPMS receiver module should be connected to constant (Klemme 30) +12V source or to the Ignition controllable (Klemme 15) +12V source, GND wire and to the CAN bus (CAN 100kbit or CAN 500kbit) wires (High and Low). TPMS adapter can operate at 100kbit or 500kbit CAN speeds. The CAN speed is configurable via TPMS utility by connecting adapter to PC. If TPMS adapter is installed in the armrest compartment or near gear shifter it is possible to use CAN signals connection, as well as power source from the wires coming to the idrive controller. It is important to ensure that the TPMS adapter is connected to the same CAN bus line as the head unit. For example in E series BMWs (E6, E7x, E8x and E9x) CAN bus coming to the idrive controller is good for connection as it goes to head unit, however drive train CAN bus is not good as it connected with different ECU. It is possible to connect TPMS wiring directly to the back of the head unit s wiring near quad lock Head unit quad lock connector pinout: Pin 12 GND Pin V klemme30 Pin 9 CAN Bus Low Pin 11 CAN Bus High

6 TPMS adapter s current consumption is no more than 85mA in active (RF receiving) mode. TPMS adapter will fall in to sleep mode as soon as ignition is turned off and vehicle goes to sleep mode. 5. Attach TPMS module plastic body at the installation location and ensure that it is secured. Picture below describes TPMS receiver s module connector pins TPMS adapter 6 pin connector pins: Pin1 GND Pin V (klemme 30 or klemme15) Pin3 CAN Bus High (100 or 500kbit) Pin4 CAN Bus Low (100 or 500kbit) Pin5 N/C Pin6 Antenna (only if provided by manufacturer)

7 In case if TPMS receiver module is connected to the idrive controller wiring you may use the following idrive controller connector pins: idrive controller 4 pin connector pins: Pin V Pin2 GND Pin3 CAN H Pin4 CAN L CAN bus speeds: BMW E series (E6x, E7x, E8x, E9x) CAN Bus at idrive controller 100kbit CAN Bus at head unit (CIC, CCC, Mask) 100kbit BMW F series F01-F12, F25 manufactured prior to 2013 March CAN Bus at idrive controller 100kbit CAN Bus at head unit (CIC, CCC, Mask) 100kbit BMW F series F20 F30 manufactured prior to 2013 March CAN Bus at idrive controller 100kbit CAN Bus at head unit (CIC, NBT) 500kbit BMW F series manufactured after 2013 March CAN Bus at idrive controller 500kbit CAN Bus at head unit (NBT) 500kbit CAN bus speed information is given for reference purpose only. It is always recommended to verify particular CAN bus speed with appropriate technical source of information.

8 6. CODING AND CONFIGURING OF HEAD UNIT It is required to perform coding of the head unit in order to ensure that TPMS adapter will properly communicate with it. Option (SA 2VB) has to be added to Vehicle order (FA) and coded in to the head unit using specialized BMW software (recommended to use services of the Independent BMW specialist or BMW dealers). This option will ensure that your head unit is configured to use TPMS module as a primary source of the information for tires pressure and temperature. In addition, if you want to monitor pressure and temperature in the head unit display you will have to manually change the following option in the head unit: RDC_SAFETY set to aktiv In E series BMWs equipped with CIC head unit there is no possibility to monitor pressure and temperature of the wheels due to software limitation of the head unit. There can be additional settings required to configure to get your head unit properly work with TPMS module. Please consult with your BMW specialist or with Bimmer Retrofit technical support.

9 7. TPMS ADAPTER CONFIGURATION UTILITY INSTALLATION TPMS Utility allows you to connect to the TPMS Adapter using USB cable and perform the following tasks: TPMS Adapter current configuration check Tire sensor add / remove for each individual tire TPMS Adapter settings configuration IMPORTANT! Be careful when connecting or using USB plug to/with Micro USB port as excessive pressure on the connector will damage the port inside of the TPMS adapter and can make device unrepairable due to internal PCB traces damage.

10 Connection of the adapter over USB requires driver installation. Currently we only provide a driver for Windows PC. This driver is usually included with utility in the download package. Driver installation procedure and other useful utility functions will be described below. Driver may be not required for Windows10 as it should install the driver automatically. 1. In order to use TPMS Utility you need to have the following: 1.1 TPMS Adapter installed in your vehicle or sitting at your table 1.2 Micro-USB to USB cable to connect TPMS adapter to your computer 1.3 Driver and Utility for TPMS Adapter which can be downloaded from here: Once you download the.zip archive please unpack it. 1.4 Windows7 based or similar computer with.net Framework installed. If required you may download.net Framework 4.5 from this link: 2. Connect your TPMS Adapter to your computer. In case the TPMS Adapter is installed in your vehicle please turn ignition ON prior to connecting the TPMS Adapter to your PC via the USB cable. You may also start engine to keep vehicle s battery charging. 3. Go to your Control Panel Device Manager and find a new device.

11 4. Right click on the new device and select Update driver mode. 5. Choose: Browse my computer for driver software 6. You may get a security prompt. Select: Install this driver software anyway

12 Warning: If you use Windows8 you may require to temporary disable Driver s Digital Signature verification before installing driver. Please check with Windows manual or Google search this information. 7. Once the driver is installed, you should see in your Device Manager new COM port device. Note its COM port number. You will need it in the next steps. 8. Start the TPMS Adapter utility called TPMS Utility. 9. In the utility click on the drop down menu and select your COM port number. It should be the same COM port number as was installed in your device manager. Normally application will already contain the number for the correct COM port entered automatically.

13 10. Click Connect button and if everything is correctly setup TPMS adapter will connect with utility. Do not forget to click Disconnect/Connect button again before you unplug USB cable from adapter. 8. USING TPMS CONFIGURATION UTILITY 1. Each TPMS Adapter comes with at least 4 sensors which are pre-coded to the adapter by manufacturer. Each TPMS sensor has unique 8 digit code which is used by TPMS adapter to identify it. Sensors are usually marked as FL, FR, RR, RL to identify the tire for installation. In order to see which sensors are currently pre-coded for your adapter press Read Sensors button in TPMS Utility.

14 2. Should you require to delete or re-code different sensors for your adapter you may do it using utility functionality. It is required to know unique 8 digits code for each sensor you plan to add to the TPMS adapter. Each additional adapter you obtain should have this code provided. Select in menu Tires for which tire the particular sensor will be installed. Next is to type 8 digit code in the Sensor ID field. Type in capital letters with no spaces. Next press Add Sensor button to add particular sensor. Confirmation and re-read of all 4 sensors currently stored in memory of TPMS adapter will follow.

15 3. TPMS Utility has list of additional commands available under Select command dropdown list. Select desired command form the list and press Execute button. Confirmation of the command execution will follow in the utility display.

16 Commands description: - Firmware update will switch module to firmware update mode. This command is equal to manual Firmware update mode - Read Settings will show on display all current adapter s settings - Set CAN100/500 will switch adapter s CAN speed to desired (100 or 500 kbps) - Read version will show current TPMS adapter s firmware version - Factory defaults will reset all settings to factory defaults - Reboot TPMS will reboot TPMS adapter (will require to re-plug USB cable) - Read Sensors will show currently stored in memory sensors - Erase all sensors will erase all sensors from memory of the adapter - Erase sensor tire will erase only the sensor for tire currently selected in Tires - Set pressure Bar/KPa/PSI will set default units for pressure - Set temp Celsius/Fahrenheit will set default units for temperature - Set last values ON/OFF will set adapter s memory for last known pressure and temperature values received from tires 9. FIRST USE OF TPMS SYSTEM As soon as TPMS adapter and wheel sensors are installed in your vehicle and coding/configuration of the head unit is done you may open Vehicles Options menu and select Tire Pressure. If everything is coded and set correctly you should see the vehicle shown with green color tires. If mode for temperature and pressure visual representation is enabled in head unit you will also see pressure and temperature information next to each tire. It is common to see --- instead of pressure and temperature after initial start. This can be shown for some or for all tires initially because tire sensors will start transmission of the information to the TPMS received only after certain conditions met (pressure or temperature changed by specific threshold). Take a short drive and let your tires warm up a little. Your TPMS receiver will start to receive the information from sensors and you will be able to see pressure and temperature information coming from the sensors in tires.

17 10. FIRMWARE UPDATE PROCEDURE FOR TPMS ADAPTER Firmware inside the TPMS Adapter should only be updated if instructed by Bimmer Retrofit or if new firmware update is released, fixing any possible bugs or making available any new features. You can always download latest firmware update via the link below: Always ensure that you download firmware SPECIFICALLY for your model of TPMS adapter. Use of firmware from other type of hardware may brick your adapter. If unsure please consult with our technical support team: This is the standard procedure for firmware update which should always be used, unless otherwise specified by Bimmer Retrofit. Whenever firmware update procedure is required please follow the steps below: 1. Make sure that you have received new firmware update file from manufacturer or downloaded it from 2. Connect TPMS Adapter with TPMS Utility and select from command drop down list Firmware update followed by Execute button press OR while TPMS adapter is not connected to vehicle and to USB cable press small button on the side of the adapter using pen. While holding the button pushed down connect USB cable to TMPS adapter. Other end of the USB cable should already be plugged to Windows based PC (sorry Mac owners, no support for you yet)

18 3. Open File Explorer. You will see that new disk drive appears in the system. 4. Open newly appeared drive. You will see there a file: firmware.bin This is old firmware which is currently installed in the TPMS adapter. 5. Delete this file with old firmware from the drive. 6. Copy new firmware update file from your computer (which you received from manufacturer or which you downloaded from to the newly appeared disk drive. You should have only one! file on this drive now. Firmware update file may have a name, which is different from firmware.bin. This is normal and no need to worry. It is important not to interrupt process of file copying during the firmware update. Also it is important to make sure that you copied proper firmware update file received from the manufacturer or downloaded from support website for your specific model of the hardware. If the firmware update file which you received from manufacturer is in.zip or.rar archive format, please un-archive it first before copying the firmware update file to the TPMS Adapter. You should copy to TPMS Adapter only firmware update file and not any other files!

19 7. Once new firmware update file is copied to TPMS Adapter s drive in your PC, wait a few seconds then disconnect USB cable from TPMS adapter. Make sure that no other power source (main harness) is connected to TPMS adapter at this time. 8. Connect USB cable back to TPMS adapter and start TPMS Utility to ensure that firmware update was properly set for the adapter and you can set connection with the adapter. 9. Add/Remove sensors and configure adapter if required. DRIVE SAFE! For all questions or other inquires please contact us at: info@bimmerretrofit.com or visit: Copyrighted Bimmer Retrofit Company. All rights reserved.