DISCONTINUED. Installation S19-310FSS. Stainless Steel Combination Drench Shower and Eyewash

Transcription

1 Stainless Steel Combination Drench Shower and Eyewash Table of Contents Pre- Information Instructions Assembly of Components Parts List FSS Rev. R; ECN Bradley Page 1 of 5 /19/01 P.O. Box 09, Menomonee Falls, WI USA PHONE 800.BRADLEY ( ) FAX bradleycorp.com

2 R Datum Signe P.O. BOX 09, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) IMPORTANT Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. THIS SIDE UP Packing List Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. P.O. Box 09, Menomonee Falls, WI 5051 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Signed Signed Unterschrift Signed Signed Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z58.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed emergency fixtures require a minimum of 0 PSI (0.1 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z58.1. The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z58.1. Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z58.1. For questions regarding the operation or installation of this product, visit www. bradleycorp.com or call BRADLEY. Product warranties and parts information may also be found under Products on our web site at /19/01 Bradley 15-16FSS Rev. R;

3 Supplies Required: () 8" floor anchors and bolts Pipe sealant Piping to 1¼" NPT water supply inlet and to 1¼" NPT drain outlet on unit Adequate supply pipe supports Min. 4 drain to accommodate 0 gallons per minute discharge for shower waste OPTIONAL: sign-mounting hardware NOTE: Local codes may require the installation of a backflow prevention valve to complete proper installation. Compliance with local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly. Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from Bradley Corporation. Step 1: Secure base to floor 1. Install three suitable anchors (supplied by installer) for 8" bolts in the floor.. Bolt the base to the floor anchors using 8" bolts (supplied by installer). Step : Assemble components 1. Assemble the remaining unit components as shown on page 4. Apply pipe sealant (by installer) to all malethreaded pipe joints. Use the rubber grip pad provided or a strap wrench around pipes when tightening to prevent marring. Place the grip pad on the pipe, then put the wrench over the grip pad and turn the pipe with the wrench. Bottom edge of showerhead should be 85" (159mm) from floor. Step : Connect water supply IMPORTANT: Do not rely on Bradley s Combination Unit to support supply piping. 1. Connect water supply piping to 1¼" NPT inlet on unit (piping by installer). Provide adequate supports (by installer) for supply pipe using pipe hangers or other means.. Connect drain piping to 1¼" NPT drain outlet on unit (piping by installer).. Hang the safety sign from the unit with the curtain hooks provided (or mount it to the wall using sign-mounting hardware by installer). 85" (159mm) to Floor ¾" (95mm) 1½" (8mm) Ø 10¾" (7mm) 9" (9mm) 10½" (67mm) 6" (660mm) 5½" (648mm) 9½" (41mm) 6" (15mm) Top View From Bowl 5¾" (146mm) 6" (914mm) 66" (1676mm) to Floor Ø 9" (9mm) Flange with () Ø 8" (10mm) Holes on Ø 8" (0mm) Bolt Circle NOTE: All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1 8" (mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1 8" (mm). Bradley 15-16FSS Rev. R; /19/01

4 P.O. BOX 09, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) P.O. Box 09, Menomonee Falls, WI 5051 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Signed Signed Datum Unterschrift Signed Signe Signed R Assembly of Components NOTE: If tee (Item ) is used as a supply inlet, use plug (Item 6) on tee (Item ). Optional 1-1/4" NPT Supply Inlet (best for rigid support) /4" NPT Supply Inlet Flow control this end NOTE: Items come preassembled as Item 9. Items come preassembled as Item /4" NPT Drain Outlet 1 4 /19/01 Bradley 15-16FSS Rev. R;

5 Parts List Item Part No. Qty. Description Item Part No. Qty. Description Base Pipe Tee 1-1/4" NPT Pipe 1¼" x ½" NPT 4 S Solid Pipe Nipple Pipe 1¼" x 6½" Pipe Plug 1¼" NPT Red. Bushing 1¼" NPT to 1" NPT NX 1 Pipe 1" NPT x 9" 9 S Stay-Open Ball Valve 1" NPT 9.1 S " Ball Valve with Nut Jam Nut only Handle Curtain Hook MN 1 Pipe 1" NPT x 1" Elbow 1" NPT 1 S Stainless Steel Showerhead A 1 Pull Rod - 5½" Long Cap Plug Red. Bushing 1¼" to ½" NPT Safety Sign Pipe ½" NPT x ½" Emergency Tag Street Elbow ½" NPT Union ½" NPT Pipe 1¼" NPT x 6½" Prepack S0-109 includes items 0, 1, 9, 0 For proper handle and ball valve kits, refer to instruction sheet S7-8 1 Ball Valve 1/" NPT with Nut Nut 16 Stainless Steel 1 S Handle Assembly Pipe ½" NPT x 4" Pipe Elbow 1-1/4 NPT Pipe Nipple 1¼" NPT x " 5 S Stainless Steel Eyewash Inlet Drain Fitting Center Seal Gasket Stainless Steel Bowl Cup Strainer 5.5 S Supply Pipe Spacer, Drain 5.7 S Eyewash Yoke Dust Cover Pipe Plug Grip Pad (not shown) DA 1 Washer R 1 Adapter Bradley 15-16FSS Rev. R; /19/01 5