Conductive Polymer Tantalum Solid Capacitors

Transcription

1 2018 Products Catalog Conductive Polymer Tantalum olid Capacitors

2 Applicable Laws and Regulations Notices This product complies with the RoH Directive (Restriction of the use of certain Hazardous substances in electrical and electronic equipment (DIRECTIVE 2011/65/EU). No Ozone Depleting Chemicals(ODC's), controlled under the Montreal Protocol Agreement, are used in producing this product. We do not PBBs or PBDEs as brominated flame retardants. Export procedure which followed export related regulations, such as foreign exchange and a foreign trade method, on the occasion of export of this product Thank you for your consideration. Limited applications This capacitor is designed to be used for electronics circuits such as audio/visual equipment, home appliances, computers and other office equipment, optical equipment, measuring equipment. High reliability and safety are required [ be / a possibility that incorrect operation of this product may do harm to a human life or property ] more. When use is considered by the use, the delivery specifications which suited the use separately need to be exchanged. Items to be observed This specification guarantees the quality and performance of the product as individual components. Before use, check and evaluate their compatibility with installed in your products. Do not use the products beyond the specifications described in this document. For specifi cations Install the following systems for a failsafe design to ensure safety if these products are to be used in equipment where a defect in these products may cause the loss of human life or other signification damage, such as damage to vehicles (automobile, train, vessel), traffic lights, medical equipment, aerospace equipment, electric heating appliances, combustion/ gas equipment, rotating rotating equipment, and disaster/crime prevention equipment. The system is equipped with a protection circuit and protection device. The system is equipped with a redundant circuit or other system to prevent an unsafe status in the event of a single fault. Conditions of use Before using the products, carefully check the effects on their quality and performance, and determined whether or not they can be used. These products are designed and manufactured for general-purpose and standard use in general electronic equipment. These products are not intended for use in the following special conditions. (1) In liquid, such as Water, Oil, Chemicals, or Organic solvent. (2) In direct sunlight, outdoors, or in dust. (3) In vapor, such as dew condensation water of resistive element, or water leakage, salty air, or air with a high concentration corrosive gas, such as Cl 2, H 2, NH 3, O 2, or NOx. (4) In an environment where strong static electricity or electromagnetic waves exist. (5) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products. (6) ealing or coating of these products or a printed circuit board on which these products are mounted, with resin and other material. (7) Using resolvent, water or water-soluble cleaner for flux cleaning agent after soldering. (In particular, when using water or a water-soluble cleaning agent, be careful not to leave water residues) (8) Using in the atmosphere which strays Acid or alkaline. (9) Using in the atmosphere which there are excessive vibration and shock. Please arrange circuit design for preventing impulse or transitional. Do not apply, which exceeds the full rated when the capacitors receive impulse, instantaneous high, high pulse etc. Our products there is a product are using an electrolyte solution. Therefore, misuse can result in rapid deterioration of characteristics and functions of each product. Electrolyte leakage damages printed circuit and affects performance, characteristics, and functions of customer system. hould a safety concern arise regarding this product, please be sure to contact us immediately. 00 Nov. 2015

3 Conductive Polymer Tantalum olid Capacitors Guidelines and precautions (POCAP) 1. Circuit design 1.1 Prohibited circuits ince problems can be expected, POCAP cannot be used on the following circuits (1) High impedance retention circuits (2) Coupling circuit (3) Time constant circuits (4) Circuits greatly affected by leakage current (5) The circuit in which two or more POCAP are connected in a series so as to raise the endurance. 1.2 Failure and life-span The failure rate is 0.5 % / 1000 h (Confidence level : 60 %) based on JI C The mainly failure modes are as follows. B2 size or less : 1.0 % Contingency failure The main causes of failure are thermal stresses cause by the soldering or thermal use environment, along with heat stresses, electrical stresses or mechanical stresses. The most common failure mode is a short circuit. In case a short circuit occurs, ensure safety by fully considering the followings. (1) If POCAP emit smoke, turn off the main power of the equipment. In this case, keep your face and hands away from the area. (2) It may take a few seconds to a few minutes before POCAP emits smoke by the situation. Increase safety by using a protective circuit. (3) If the smoke comes into eyes, rinse immediately. If the smoke is inhaled, gargle immediately. (4) In case a large current continues to flow after a short circuit, in the worst case, the shorted-out section may ignite. For safety, install a redundant circuit or a protective circuit, etc Wear-out failure (lifetime) When lifetime exceeded the specified guarantee time of Endurance and Damp heat, electrolyte might insulate and cause electric characteristic changed. This is called an open circuit. The electric characteristics of capacitance and ER may possibly change within the specified range in specifications when it is used under the condition of the rated, electric and mechanical performance. Please note it when design. 1.3 Reduction of failure stress When POCAP is used within the rated, it shows a stable characteristic, but it may be damaged in a short circuit when an over, for instance, is applied. The time to reach the failure mode can be extended by using POCAP with reduced environment temperature, ripple current and applied. Failure rate In the case of the endurance which is 105 C 2000 h. 0.5 %/1000 h (Environment : 105 C, or applied) In the case of the endurance which is 105 C 1000 h or 125 C 1000 h. 1.0 %/1000 h (Environment : 105 C, or applied) In the case of the endurance which is 85 C 1000 h. 1.0 %/1000 h (Environment : 85 C, applied) 1.4 Check the rated performance After checking the operation and installation environments, design the circuit so that it falls within the rated performance range stipulated in this delivery specification. 1.5 Operating temperature and ripple current (a) et the operating temperature so that it falls within the range stipulated in this delivery specification. (b) Do not apply current that exceeds the allowable ripple current. Ripple current should be controlled so that surface temperature of a capacitor do not exceed the rated temperature. (For questions regarding TQC series, please contact us.) (c) pecified ER is a value at the time of shipping from factory. ER may change upon use conditions. hould a safety concern arise regarding this product, please be sure to contact us immediately. 05 Mar. 2018

4 Conductive Polymer Tantalum olid Capacitors 1.6 Leakage current Even when the soldering conditions fall within the range of this delivery specifications, leakage current increases a little on occasion. It also increases a little during high temperature storage, high humidity storage and temperature cycling with no applied. In cases such as these, leakage current will decrease by applying under the condition of below the POCAP's maximum operating temperature. The speed at which the leakage current is restored is increased by applying when the POCAP's temperature is close to the maximum operating temperature. 1.7 Rapid charge and discharge limitation Rapid charge and discharge are restricted (for maintainance of high-proof reliability). A protective circuit is recommended for when a rapid charge or discharge causes excessive rush current since this is main cause of short circuit and large leakage current. Use a protective circuits in case the rush current value exceeds 20 A. Be sure to insert a protection resistor of about 1 kω for charge and discharge when measuring the leakage current. When TH series use under the ambient temperature more than 105 C : 10 A TPU series : 10 A 2. Mounting 2.1 Protect circuit The failure mode of POCAP is the short mode. When it breaks down, short electric current flows to it. POCAP gives off heat by this short current. Do the following consideration in design fully for the safety because it has a bad influence on the part around POCAP due to this heat. A protective circuit and a protective device are set up, so as to make the system safer. A diffuse circuit and so on is set up, so as to make the system safer such as that a machine may not break down as to the single trouble. 2.2 Considerations when soldering The soldering conditions are to be within the range prescribed in this delivery specification. If the specifications are not followed, there is the possibility of degradation of electric characteristic and lifetime when soldering is conducted under conditions that are harsher that those stipulated. 2.3 Others POCAP s Electrical characteristics are affected by temperature and frequency fluctuations. Design circuits after checking the amount of fluctuation. 3. torage It is necessary to set an environment to prevent a trouble at the time of soldering by the degradation of solder ability or moisture's getting into the molding resin when POCAP are stored. Please make storage of POCAP sealing up in the reel and storage bag at the time of delivery in the following environment. Also, set storage period of unopened as 18 months or shorter after shipment from factory. Room temperature and room humidity (generally : 15 to 35 C, 45 to 75% RH ) are desirable. Place where POCAP is not exposed by direct sunshine. Please unseal storage bag just before mounting and use up POCAP in the storage bag. The floor life after opening the bag are different by each part numbers. Please refer product specification, or contact us. Floor life Time Conditions 4 weeks < 30 C/60 %Rh 168 hours < 30 C/60 %Rh 48 hours < 30 C/60 %Rh POCAP is not compatible with JEDEC J-TD-020, J-TD-033 Intellectual property right We, Panasonic Group are providing the product and service that customers can use without anxiety, and are working positively on the protection of our products under intellectual property rights. Representative patents relating to POCAP are as follows: U Patent Nos and hould a safety concern arise regarding this product, please be sure to contact us immediately. 05 Mar. 2018

5 Conductive Polymer Tantalum olid Capacitors

6 Conductive Polymer Tantalum olid Capacitors

7 Conductive Polymer Tantalum olid Capacitors

8 Conductive Polymer Tantalum olid Capacitors

9 Conductive Polymer Tantalum olid Capacitors Mounting specifications Recommendable refl ow soldering <Recommended refl ow soldering temperature profi le> <Peak temperature 250 C lead free refl ow soldering profi le> Temperature on the surface of capacitor 240 C 200 C 150 C 60 s max 120 s max Time (sec.) 40 s max 30 s max Peak temperature 5 s max Temperature on the surface of capacitor 250 C 220 C 180 C 150 C 60 s max 120 s max Time (sec.) 40 s max 30 s max Peak temperature 5 s max The cycles of refl ow soldering : Twice (max) The cycles of refl ow soldering : Twice (max) <Peak temperature 260 C lead free refl ow soldering profi le> Temperature on the surface of capacitor 260 C 217 C 200 C 150 C 60 s max 180 s max 6 s max Time (sec.) The model of ML 2a is changed into ML 3 with this refl ow condition. Peak temperature 5 s max 90 s max The cycles of refl ow soldering : Twice (max) <TQC/TQ series> Temperature on the surface of capacitor 250 C 217 C 200 C 180 C 150 C 120 s max Time (sec.) 60 s max 70 s max Peak temperature 10 s max The cycles of refl ow soldering : Twice (max) oldering with a soldering iron Tip of a soldering iron : 350 C max (TQC/TQ series : 400 C max) Power of a soldering iron : 30 W max Working time : 3 sec. max (TQC/TQ series : 5 sec max) (Do not let the tip of soldering iron touch the POCAP itself. Do not subject the POCAP itself to excessive stress when soldering.) Land Pattern a c a b ize code a b c A09, A B09, B1, B1, B1G, B15G, B2, B D12, D15, D15E, D2E, D2, D3L, D hould a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jul. 2016

10 Conductive Polymer Tantalum olid Capacitors Packing specifications Dimension of carrier tape procket hole A J Component compartment (Polarity) D E C ( ) K t B F G H (+) Direction of unreeling ize code A±0.1 B±0.1 C±0.3 D±0.05 E±0.1 F±0.1 G±0.05 H±0.1 J K±0.1 t± f A f A f B f B f B f B1G f B15G f B f B f D f D f D15E f D2E f D f D3L f D f Dimension A and B are the measure of compartment's inside bottom. The (+) Polarity of the chip is placed on right side towards the unreeling direction. Dimension of the topcover tape Thickness of cover tape: 62±10 μm Width of cover tape : 9.5±0.2 mm 5.5±0.2 mm (f180 reel) Reel dimension Dimension of packing case C B A W2 W1 A B C W1 W2 f330±2 f80±2 f13.0± ± ±1.0 0 f180 3 f60±2 f13.0± ± ±1.0 Minimum packing quantity and weight ize code Quantity (pcs./reel, f180) Typical weight (g) 09, A A B09, B B1, B1G B15G B2, B ize code Quantity (pcs./reel, f330) Typical weight (g) D D D15E D2E, D D3L D mall order quantity (500 pcs/reel) is available with TPE, TPF and TQC series. Please contact our sales representative if you prefer it. a b c Reel size f180 f330 a b c Units per packing case ize code Pieces/case 09, A A B09, B B1, B1G B15G B2, B ize code Pieces/case D D D15E D2E, D D3L D hould a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jul. 2016

11 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPU Features mall size, Low profi le (L2.0 W 1.25 H 0.9 mm) Face down terminal type RoH compliance, Halogen free ize code 09 B09 temperature range 55 C to +85 C range 2.5 V.DC to 10 V.DC 6.3 V.DC range 2.5 V.DC to 10 V.DC 6.3 V.DC capacitance range 4.7 μf to 100 μf 150 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h, rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat Capacitance change Within +40 %, 20 % of the initial value (teady tate) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) 09 ize Polarity marking(+) B09 ize Polarity marking(+) L W R. Voltage code Lot. No. R. Voltage code R. Voltage Code e g j A Lot. No. 09 ize R. Cap. (μf) Code s A J W A B09 ize R. Cap. (μf) 150 Code E8 ize code L±0.1 1 W±0.1 1 H±0.1 ±0.1 1 W1± B Externals of fi gure are the reference. H W1 1 ±0.2 : B09 Characteristics list eries TPU capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) R5TPU47MI ETPU100MI TPU68MI TPU10MI TPU22MI TPU47MI B TPU150MBI TPU4R7MI Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

12 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPH Features mall size, Low profi le (L3.2 W 1.6 H 0.9 mm) Face down terminal type RoH compliance, Halogen free ize code A09 A14 temperature range 55 C to +105 C / 55 C to +85 C ( +85 C) range 2.5 V.DC to 10 V.DC 2.5 V.DC to 6.3 V.DC range 2.5 V.DC to 10 V.DC 2.5 V.DC to 6.3 V.DC capacitance range 33 μf to 100 μf 100 μf to 220 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h rated applied temp, +85 C Products : +85 C, 1000 h, rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Within +50 %, 20 % of the initial value (ETPH220MABC) Damp heat Capacitance change Within +40 %, 20 % of the initial value (Except for above model) (teady tate) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) A09/A14 ize A09 ize (6TPH100MAEA) A09/A14 ize A09 ize (6TPH100MAEA) Polarity marking(+) Polarity marking(+) L L Year Year Week Week W W R. Voltage code R. Voltage code H H R. Voltage Code e g j A R. Cap. (μf) Code N7 7 W7 A8 E8 J8 W1 W1 ize code L±0.2 W±0.2 H±0.1 ±0.2 W1±0.1 A A Externals of fi gure are the reference. Characteristics list eries TPH capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) A ETPH100MHA A ETPH220MABC A TPH68MHA A TPH150MABC TPH47MHA 3000 A TPH100MAEA A TPH100MABC A ATPH33MAHA Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

13 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPG Features mall size, Low profi le (L3.5 W 2.8 H 1.1 mm) Large capacitance (220 μf max.) RoH compliance, Halogen free ize code B1G B15G temperature range 55 C to +105 C range 2.5 V.DC to 12.5 V.DC 2.5 V.DC to 6.3 V.DC range 2.0 V.DC to 10.0 V.DC 2.0 V.DC to 5.0 V.DC capacitance range 33 μf to 220 μf 150 μf to 220 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat Capacitance change Within +40 %, 20 % of the initial value (teady tate) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) Polarity marking(+) W R. Voltage code Lot. No. R. Voltage Code e g j k A B R. Cap. (μf) Code N7 7 A8 E8 J8 H W1 ize code L W H±0.1 ±0.2 W1±0.1 B1G B15G Externals of fi gure are the reference. Characteristics list eries TPG capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) B1G R5TPG220M /300 khz R5TPG220MUG 2500 B15G TPG220M TPG100M B1G TPG100MG /300 khz TPG100MZGD TPG150M B15G /300 khz TPG150MZG TPG47M B1G TPG47M TPG33M Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

14 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPF Features uper low ER (6 mω max.) uper low EL (0.7 nh) Face down terminal type RoH compliance, Halogen free ize code B2 temperature range 55 C to +105 C range range capacitance range Capacitance tolerance 2.0 V.DC to 2.5 V.DC 2.0 V.DC to 2.5 V.DC 270 μf ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge 1.15 Endurance Damp heat (teady tate) +105 C, 1000 h rated applied Capacitance change tan d DC leakage current Within ±20 % of the initial value < 1.5 times of the initial limit Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Capacitance change tan d DC leakage current Within +40 %, 20 % of the initial value < 1.5 times of the initial limit < 3 times of the initial limit Marking Dimensions (not to scale) Polarity marking(+) R. Voltage code L W Lot. No. H W1 R. Voltage Code d e ize code L±0.2 W±0.2 H±0.1 ±0.3 W1±0.1 R. Cap. (μf) 270 B Code L8 Externals of fi gure are the reference. Characteristics list eries TPF capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) /500 khz TPF270M6E B /300 khz TPF270M9G /500 khz ETPF270M6E Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

15 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPE ize : B Features mall size (L 3.5 W 2.8 H 1.9 mm) Low ER (15 mω) RoH compliance, Halogen free ize code temperature range 55 C to +105 C range 2.0 V.DC to 10 V.DC range 1.8 V.DC to 8.0 V.DC capacitance range 47 μf to 470 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h rated applied temp, +85 C Products : +85 C, 1000 h, rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat (teady tate) Capacitance change tan d DC leakage current B2 Within +50 %, 20 % of the initial value (2R5TPE220MAZB (MAPB, MAFB), 2R5TPE330MAZB, 2TPE330MAFB (MADGB), 2TPE470MAJGB (MAFB), 2TPE330MFB, ETPE330MAFB (MA9GB)) Within +40 %, 20 % of the initial value (Except for above model) < 1.5 times of the initial limit < 3 times of the initial limit Marking Dimensions (not to scale) Polarity marking(+) L R. Voltage code Lot. No. H W R. Voltage Code d e g j k A R. Cap. (μf) Code 7 A8 C8 E8 J8 N8 8 ize code L±0.2 W±0.2 H±0.1 ±0.2 W1±0.1 B Externals of fi gure are the reference. W1 hould a safety concern arise regarding this product, please be sure to contact us immediately. 04 Mar. 2018

16 Conductive Polymer Tantalum olid Capacitors Characteristics list eries TPE NEW NEW NEW capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) TPE330MFB TPE330MAFB /300 khz TPE330MADGB TPE470MAFB /300 khz TPE470MAJGB R5TPE220MAFB /300 khz R5TPE220MFGB R5TPE220MLB R5TPE220MAPB R5TPE220MZB R5TPE220MAZB R5TPE330MAZB /300 khz ETPE330MA9GB /300 khz ETPE330M9GB B ETPE330MAFB ETPE330MFB TPE100MZB TPE150MAZB TPE220MAZB TPE100MPB TPE100MAZB TPE100MZB TPE120MAZB TPE150MAPB TPE150MAZB TPE220MAZB NEW TPE220MAPB TPE100MAZB TPE47MAZB Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 04 Mar. 2018

17 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPE ize : D Features Low profi le (Height 1.5 mm max.) Low ER (7 mω) Large capacitance (1500 μf max.) RoH compliance, Halogen free ize code D15E D2E D3L D4 temperature range 55 C to +105 C range 6.3 V.DC 2.5 V.DC to 10 V.DC range 5.0 V.DC 2.5 V.DC to 10 V.DC capacitance range 470 μf 68 μf to 470 μf 220 μf to 680 μf 330 μf to 1500 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 2000 h rated applied temp, +85 C Products : +85 C, 1000 h, rated applied 6TPE330MAP, 6TPE470MAZU : +85 C, 2000 h, Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat (teady tate) Capacitance change tan d DC leakage current Within +50 %, 20 % of the initial value (2R5TPE220M (I, F, 9), 2R5TPE330M (I, F, C, 9, 7), 2R5TPE470M (I, F, C, 9, 7), 2R5TPE1000MF, 2R5TPE1500M (F, C)) Within +40 %, 20 % of the initial value (Except for above model) < 1.5 times of the initial limit < 3 times of the initial limit Marking Dimensions (not to scale) L Polarity marking(+) W H R. Voltage code Lot. No. ize code L±0.3 W±0.2 H±0.2 1 ±0.2 W1±0.1 D15E D2E D3L R. Voltage D Code e g j A Externals of fi gure are the reference. 1 ±0.1 :D15E, D2E W1 hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

18 Conductive Polymer Tantalum olid Capacitors Characteristics list eries TPE capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) R5TPE220M R5TPE220MF R5TPE220MI R5TPE220M R5TPE330M R5TPE330M R5TPE330MC D2E R5TPE330MF R5TPE330MI R5TPE330M R5TPE470M R5TPE470M R5TPE470MC R5TPE470MF R5TPE470MI R5TPE680MCL D3L R5TPE680MFL R5TPE1000MF D R5TPE1500MC R5TPE1500MF TPE150MI TPE220MF TPE220MI 3000 D2E TPE220M TPE330MI TPE330M TPE470MCL TPE470MFL D3L TPE470MIL TPE470ML TPE100MI TPE100M TPE150MF TPE150MI D2E TPE150M TPE220MI TPE220M TPE220MAP TPE330MAP TPE330MAL /500 Hz TPE330MA9EL D3L TPE330MFL TPE330MIL TPE330ML D TPE330MAA D15E TPE470MAZU TPE470MI TPE470M 2000 D TPE680MI TPE680M D2E TPE68M TPE220MIL D3L TPE220ML D TPE330M Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

19 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPF Features uper low ER (5 mω max.) Large capacitance (1000 μf max.) RoH compliance, Halogen free ize code D2E D3L D4 temperature range 55 C to +105 C range 2.0 V.DC 2.5 V.DC to 10 V.DC 2.5 V.DC to 6.3 V.DC range 2.0 V.DC 2.5 V.DC to 10 V.DC 2.5 V.DC to 6.3 V.DC capacitance range 220 μf to 330 μf 150 μf to 680 μf 470 μf to 1000 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge 1.15 Endurance Damp heat (teady tate) +105 C, 2000 h rated applied Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Within +50 %, 20 % of the initial value Capacitance change (2TPF220M6, 2TPF330M6, ETPF1000M6H (5H)) Within +40 %, 20 % of the initial value (Except for above model) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) L Polarity marking(+) W H R. Voltage code Lot. No. R. Voltage Code d e g j A ize code L±0.3 W±0.2 H±0.2 1 ±0.2 W1±0.1 D2E D3L D Externals of fi gure are the reference. 1 ±0.1 :D2E W1 hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

20 Conductive Polymer Tantalum olid Capacitors Characteristics list eries TPF capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) TPF220M D2E TPF330M R5TPF330M7L R5TPF470M6L 2500 D3L R5TPF470M7L R5TPF470ML D ETPF470M5H R5TPF680M6L D3L R5TPF680M7L R5TPF680ML ETPF680M5H D ETPF1000M5H ETPF1000M6H TPF330ML 2500 D3L TPF470ML D TPF680MAH TPF220M5L TPF220M9L 2500 D3L TPF220ML TPF330M9L D TPF470MAH D3L TPF150ML Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

21 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TQ Features High (35 V.DC max.) RoH compliance, Halogen free ize code B1 temperature range 55 C to +105 C range 16 V.DC to 35 V.DC range 16 V.DC to 35 V.DC capacitance range 6.8 μf to 33 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h, rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit Damp heat (teady tate) +60 C, 90 % to 95 %, 500 h, No-applied Capacitance change Within +40 %, 20 % of the initial value DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) Polarity marking(+) R. Voltage code L W R. Voltage Code C E V R. Cap. (μf) Code W6 A7 N7 Lot. No. H W1 ize code L±0.2 W±0.2 H±0.1 ±0.3 W1±0.1 B Externals of fi gure are the reference. Characteristics list eries capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) TQ33MBD 2500 TQ B TQ10MED TQ6R8MHD Ripple current (100 khz/ +105 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 00 Jul. 2016

22 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TQC ize : B Features High (35 V.DC max.) RoH compliance, Halogen free ize code B2 temperature range 55 C to +105 C range 16 V.DC to 35 V.DC range 16 V.DC to 35 V.DC capacitance range 3.9 μf to 33 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 2000 h (16TQC33MYFB : 1000 h), rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat Capacitance change Within +40 %, 20 % of the initial value (teady tate) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) Polarity marking(+) H W R. Voltage code Lot. No. W1 R. Voltage Code C D E V R. Cap. (μf) Code Q6 U6 Y6 A7 E7 J7 N7 ize code L±0.2 W±0.2 H±0.1 ±0.2 W1±0.1 B Externals of fi gure are the reference. Characteristics list eries capacitance (μf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) TQC10M TQC15M TQC33MYFB 2000 TQC TQC8R2M 2000 B TQC22MYFB TQC5R6M TQC15MYFB TQC3R9MYF Ripple current (100 khz/ +105 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 02 Jul. 2016

23 NEW NEW

24 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TA This product is not intended for use in any driving application or any other critical functions that affect passenger safety. (e.g. Powertrain, AB, Engine ECU, Airbag, etc.) If the intended use of TA/TV series products is for use in other automotive related applications, please contact our sales team. All requests are subject to approval. Features Guaranteed at 85 C 85 %RH RoH compliance, Halogen free ize code B2 D2E D3L temperature range 55 C to +105 C range 4 V.DC to 10 V.DC 2.5 V.DC to 10 V.DC range 4 V.DC to 10 V.DC 2.5 V.DC to 10 V.DC capacitance range 47μF to 100 μf 68 μf to 470 μf 150 μf to 680 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 2000 h, (B2 size : 1000 h) rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +85 C, 85 % to 90 %, 500 h, rated applied Within +50 %, 20 % of the initial value (2R5TAE470M(F), 2R5TAE330M(F, I), 2R5TAE220M(F, 9)) Damp heat Capacitance change Within +40 %, 20 % of the initial value (Except for above model) (teady tate) DC leakage current Within the initial limit Marking D2E, D3L ize Polarity marking(+) R. Voltage code Lot. No. eries TA B2 ize Polarity marking(+) R. Voltage code Characteristics list Lot. No. capacitance (μf) R. Voltage Code e g j A B2 ize R. Cap (μf) Code 7 W7 A8 Case size (mm) L W H ize code Dimensions (not to scale) Ripple 1 current (mar.m.s.) L W H ER 2 (mω max.) W1 tan d 3 4 LC (μa) tandard Part number Min. Packaging Q'ty (pcs) R5TAE220M R5TAE220MF R5TAE220M R5TAE330MF 3000 D2E R5TAE330MI R5TAE330M R5TAE470MF R5TAE470M R5TAE680MFL D3L R5TAE680ML B TAB100M TAE220MI D2E TAE220M TAE470MIL D3L TAE470ML TAB47M 2000 B TAB68M TAE150M D2E TAE220MI TAE220M D3L TAE330ML B TAB47M D2E TAE68M TAE150ML 2500 D3L TAE220ML Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. ize Code L±0.3 1 W±0.2 H±0.2 2 ±0.2 W1±0.1 B D2E D3L Externals of fi gure are the reference. 1 ±0.2 : B2 2 ±0.1 : B2, D2E hould a safety concern arise regarding this product, please be sure to contact us immediately. 02 Mar. 2018

25 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TV This product is not intended for use in any driving application or any other critical functions that affect passenger safety. (e.g. Powertrain, AB, Engine ECU, Airbag, etc.) If the intended use of TA/TV series products is for use in other automotive related applications, please contact our sales team. All requests are subject to approval. Features Guaranteed at 85 C 85 %RH Guaranteed at 125 C RoH compliance, Halogen free ize code D2E D3L temperature range 55 C to +125 C range 6.3 V.DC to 10 V.DC 10 V.DC range 4.0 V.DC to 6.3 V.DC 6.3 V.DC capacitance range 68 µf to 150 µf 150 µf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C, 1000 h, category applied (+105 C 2000 h, rated applied) Endurance 125 C 105 C Capacitance change Within ±20 % of the initial value Within ±20 % of the initial value tan d < 2 times of the initial limit < 1.5 times of the initial limit DC leakage current < 2 times of the initial limit Within the initial limit Damp heat (teady tate) +85 C, 85 % to 90 %, 500 h, rated applied Capacitance change Within +40 %, 20 % of the initial value DC leakage current Within the initial limit Marking Dimensions (not to scale) L Polarity marking(+) W H R. Voltage Code j A R. Voltage code Lot. No. W1 ize code L±0.3 W±0.2 1 H±0.2 ±0.2 W1±0.1 D2E D3L Externals of figure are the reference. 1 ±0.1 : D2E Characteristics list eries TV capacitance (µf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (µa) tandard Part number Min. Packaging Q'ty (pcs) D2E TVE150M TVE68M D3L TVE150ML Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 02 Mar. 2018

26 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TH Features Guaranteed at 125 C, 1000h RoH compliance, Halogen free ize code D2E D2 D3L D4 temperature range 55 C to +125 C range 2.5 V.DC to 6.3 V.DC 2.5 V.DC to 10 V.DC 4 V.DC to 6.3 V.DC 6.3 V.DC to 10 V.DC range 1.6 V.DC to 4.0 V.DC 1.6 V.DC to 6.3 V.DC 2.5 V.DC to 4.0 V.DC 4.0 V.DC to 6.3 V.DC capacitance range 150 µf to 330 µf 68 µf to 220 µf 220 µf to 330 µf 220 µf to 470 µf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C 1000h, category appled Endurance Capacitance change Within ±20 % of the initial value tan d < 2 times of the initial limit DC leakage current < 2 times of the initial limit Damp heat (teady tate) Marking D2E, D3L ize +60 C, 90 % to 95 %, 500 h, No-applied Capacitance change Within +40 %, 20 % of the initial value DC leakage current < 3 times of the initial limit D2, D4 ize Dimensions (not to scale) Polarity marking(+) Polarity marking(+) H W R. Voltage code Lot. No. R. Voltage Code e g j A R. Voltage code Lot. No. ize code L±0.3 1 W±0.2 H±0.1 2 ±0.2 W1±0.1 D2E D D3L D Externals of figure are the reference. 1 ±0.2 : D2 2 ±0.2 :D3L, D4 W1 Characteristics list eries capacitance (µf) Case size (mm) L W H ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (µa) tandard Part number Min. Packaging Q'ty (pcs) THB330ML 2500 D3L THB220ML THB330M 2000 THB THB470M 2000 D THB220M THB330M R5THC220M 3000 THC D THC150M THC68M R5THE330MF R5THE330MI R5THE330M 3000 THE THE220MF 3000 D2E THE220MI THE220M THE150MI THE150M Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015

27 Conductive Polymer Tantalum olid Capacitors urface Mount Type eries : TPB Features tandard RoH compliance, Halogen free ize code B2 D3L D4 temperature range 55 C to +105 C range 4 V.DC to 10 V.DC 6.3 V.DC to 10 V.DC range 4 V.DC to 10 V.DC 6.3 V.DC to 10 V.DC capacitance range 33 μf to 68 μf 150 μf to 330 μf 220 μf to 470 μf Capacitance tolerance ±20 % (120 Hz / + 20 C) Leakage current Dissipation factor (tan d) urge C 2000h, (B2 size : 1000h) rated appled +85 C 1000h rated applied Endurance Capacitance change Within ±20 % of the initial value DC leakage current Within the initial limit +60 C, 90 % to 95 %, 500 h, No-applied Damp heat Capacitance change Within +40 %, 20 % of the initial value (teady tate) DC leakage current < 3 times of the initial limit Marking Dimensions (not to scale) B2 ize D4 ize L Polarity marking(+) Polarity marking(+) W R. Voltage code Lot. No. R. Voltage code Lot. No. R. Voltage code Lot. No. D3L ize R. Voltage Polarity marking(+) Code g j A B2 ize R. Cap. (μf) Code N7 7 W7 W1 ize code L±0.3 1 W±0.2 H±0.2 2 ±0.2 W1±0.1 B D3L D Externals of fi gure are the reference. 1 ±0.2 : B2 2 ±0.1 : B2 H Characteristics list Case 10.0 size (mm) eries d e gcapacitance j A (μf) L W H TPB ize code Ripple 1 current (mar.m.s.) ER 2 (mω max.) tan d 3 LC 4 (μa) tandard Part number Min. Packaging Q'ty (pcs) B TPB68M D3L TPB330ML B TPB68M TPB220ML D3L TPB330MAL TPB330ML TPB330M 2000 D TPB470M TPB33M 2000 B TPB47M TPB150ML 2500 D3L TPB220ML TPB220M 2000 D TPB330M Ripple current (100 khz/ +45 C ), 2 ER (100 khz/+20 C) 3 tan d (120 Hz/+20 C) 4 After 5 minutes Please refer to each page in this catarog for Reflow conditions and Taping specifications. hould a safety concern arise regarding this product, please be sure to contact us immediately. 01 Nov. 2015