CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITOR

Transcription

1 CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITOR 1

2 Application Guidelines 1. Polarity CSCAP is solid aluminum electrolytic capacitors with positive and negative electrodes. Do not reverse the polarity when using. If it is used with the polarities reversed, its life may shorten because of increasing leakage current or short circuit. 2. Prohibited circuits Since problems can be expected due to leakage current increasing during soldering and other processes, CSCAP cannot be used in the following circuits: (1) High impedance circuits (2) Coupling circuits (3) Time constant circuits (4) Connection of two or more capacitors in series for higher withstand voltage (5) Circuits to get bad influence by big leakage current * In addition to the leakage current fluctuation above, the operational conditions such as characteristics at high and low temperature, damp heat and endurance stipulated in the specifications will affect the capacitance. The fluctuation of the capacitance may cause problem if it is used as a time constant capacitor, which is extremely sensitive to the fluctuation of the capacitance. Do not use it as a time constant capacitor. Additionally, please contact Taiwan Chinsan Electronic Industrial Co., Ltd. for usage of two or more CSCAP in series for voltage proof. 3. Over voltage Over voltage exceeding the rated voltage may not be applied even for an instant as if may cause a short circuit. 4. Sudden charge and discharge Sudden charge and discharge restricted (for maintenance of highproof reliability).a protection circuit is recommended for when a sudden charge or discharge causes excessive rush current because this is a main cause of short circuits and large leakage current. Use protection circuits if the rush current exceeds 10A. The rush current exceeds 10 the maximum allowable ripple current of CSCAP. Be sure to insert a protection resistor of about 1kΩ for charge and discharge when measuring the leakage current. 5. Soldering The soldering conditions are to be within the range prescribed in the specifications. If the specifications are not followed, there is the possibility of the appearance becoming defective and of increase of abnormal leakage current and capacity reduction when soldering is conducted under conditions that are harsher than those stipulated. Sufficient PCB installation space(pcb means Printed Circuit Board after this.) Sealing resin of CSCAP may have a bulge. The design must give consideration to the standard of height and lead position displacement given in the specifications. 6. Use of CSCAP for industrial equipments To ensure reliability when the CSCAP is used in industrial equipments, design must allow for its capacitance, impedance and other characteristics. 7. Use of CSCAP for human life equipments In case of using in equipments regarding human life (e.g. Space equipment, aeronautic equipment and atomic equipment etc.), be sure to talk over the matter with Taiwan Chinsan Electronic Industrial Co., Ltd. Don t use without recognition document of Taiwan Chinsan Electronic Industrial Co., Ltd. 2

3 8. Storage (1) Store CSCAP with the temperature range between 15 to 35 and the relative humidity of 75% or less without direct sunshine and store CSCAP in the package states if possible. (2) CSCAP are recommended that you shall open the bag just before use and CSCAP shall be used up. (3) Never store CSCAP in which it is directly exposed to water, brine, oil or in condensation status. (4) Never store CSCAP in any area filled with poisonous gases(including hydrogen sulfide, sulfurous acid, nitrous acid, chlorine and ammonia). (5) Never store CSCAP in any area to which ultraviolet and/or radial rays are radiated. 9. Cleaning Concerning about HCFC, higher alcohol system, petroleum system, terrene system, water system with surface active agent and other solvents the washing way (separateness or combinations) by soak, ultrasonic wave, boil, vapor etc. is confirmed under the maker s recommendation. Please contact us if you require further details. 10. Notes on circuit designs for CSCAP 10.1 Performance Use CSCAP within the rating and performance ranges defined in this specifications Operating temperature and ripple current If CSCAP is used at a temperature higher than the upper category temperature, or excess ripple current flows through CSCAP, there are high possibilities of life cycle reduction or leakage current increasing to cause CSCAP defective The leakage current of CSCAP may increase slightly by soldering conditions. The application of DC voltage enables the capacitors to be repaired by itself and this leads the leakage current to be smaller gradually Applied voltage For the reliability of CSCAP, it is recommended that the voltage applied to the peak value of the ripple voltage should be less than the rated voltage Failure mode CSCAP contains a conductive polymer. The life ends mostly due to random failure mode, mainly short circuit. In case of short circuit, CSCAP can be overheated by continuous current flow, the case of CSCAP would be removed by internal pressure increasing Insulation Plastic coated case of CSCAP can t guarantee the insulation. Do not use CSCAP in areas requiring insulation. 3

4 11. Soldering condition for CSCAP 11.1 Wave soldering condition for DIP type Temperature Time Preheating 125 Max Within 120 sec Soldering condition 2605 Max Within 10 sec 11.2 Reflow soldering condition for SMD type Preheat >217 >230 Peak Temp Reflow times 150 ~ MAX 1 cycle only 50sec Max 40s Max 120Sec Max 250 MAX 2 cycle allowed ( ) Temperature on the top of capacitor. and Temperature of capacitor terminal. Peak Preheat Peak temperature. Max periodof time over 230 Max period of time over 217 Time ( Sec.) 4

5 Capacitor Series Table Series Page Features Voltage Range (Vdc) Capacitance Range (μf) Operating Temperature Range ( C) Endurance (Hours) UPS 9 Super Low 7 mω and Large Capacitance 2.5 to to 2, to 105 2,000 UPR 11 Super Low 8 mω and Small size 2.5 to to to 105 2,000 DIP UL 13 Small size, Low profile and Low 2.5 to to to 105 2,000 UPE 15 Super Low Endurance 105 5,000 hours 2.5 to to 1, to 105 5,000 RP mω 2.5 to to 2, to 105 2,000 RH 19 Higher heat resistance 125 High reliability 2.5 to to 1, to 125 2,000 GP 21 Low and High voltage 10 to to 1, to 105 2,000 GV 23 High reliability and High voltage 25 to to to 105 2,000 GS 25 Low and Large Capacitance 16 to to 2, to 105 2,000 SG 27 Low and High voltage 2.5 to to 2, to 105 2,000 SMD SP 29 Super Low 2.5 to to 2, to 105 2,000 SU 31 Ultra Low 2.5 to to to 105 2,000 SE 33 Low, Long Life 5,000 hours 2.5 to to to 105 5,000 5

6 MARKING AND DATE CODE Trade mark(chinsan) Negative Polarity Series C s UPE Code Capacitance Voltage E C s UPE Trade Mark "CS" Chinsan Solid Capacitor, Show on Dimension 8φ Code (Date Code) (1) (2) (3) (1)DAY Code Day 1st~10th 11~20th 21st~31st (2)Month Code Month Jan Feb Mar Apr May Jun Code X Y Z Month July Aug Sep Oct Nov Dec (3)Year Code Year Series (Print Code) Series UPS UPR UL UPE RP RH GP GV GS SG SP SU SE Ø5~ Ø6.3 R L E H P V G P U E Ø8~ Ø10 UPS UL UPE RP RH GP GV GS SG SP SU SE LEAD FORMING TYPE Type Part Number ΦD F ι Dimensions (Unit: mm) L (Part number for lead length and pitch for taping) 3 4 U 7 D X R B E G 2 M T ±0.5 ±0.2 ± Cut C D F 10 5 L 6

7 TAPING Figure 1 Symbol Tolerance Ф 5 Ф 6.3 Ф 8 PS P5 PS P5 PS P5 Фd ± / P ± P0 ± P1 ± P2 ± F H ± H0 ± W ± W0 Minimum D0 ± t ± Figure 2 Symbol Tolerance Ф 6.3 Ф 8 Ф 10 P2 P3 H3 P7 P5 Фd ± / P ± P0 ± P1 ± P2 ± F H ± H0 ±0.5 W ± W0 Minimum D0 ± t ± Figure 3 Symbol Tolerance Ф 5 PZ Фd ± P ± P0 ± P1 ± P2 ± F H ± H0 ±0.5 W ± W0 Minimum 12.5 D0 ±0.2 4 t ±

8 PART NUMBER SYSTEM RADIAL LEAD TYPE Series Voltage Capacitance Tolerance Lead Forming Type Lead Length Case Dimension Special Request (1) (2) (3) (4) (5) (6) (7) (8) (1) Series Series DIP UPS UPR UL UPE RP RH GP GV GS SMD SG SP SU SE (2) Voltage Code 0E 0J 6K 7H 1A 1B AG 1C 1D 1P 1E 1F 1V 1H 1J 2A WV (3) Capacitance Code μf (4) Capacitance Tolerance Code J Q R K V M H % ± 5 30 / / 0 ± / 10 ± / 5 (5) Lead Type Code C P Description Cutting Taping Drawing Page6 Page7 (6) Lead Length (Cut / Formed lead) Code 3 4 U 7 D X R B E G 2 M T N Length mm min Tolerance ±0.5 ±0.2 ±0.3 15mm min Taping Code Code Z S Lead Pitch:0.8/ (7) Case Dimension DIP Code Size SMD Code Size (8) Special Request Code R F L D Description High ripple current Endurance Low Leakage Current Low Dissipation Factor Code U E P Description Convex Rubber Low PET Sleeve 8

9 UPS Series Super low at a high frequency range High ripple current capability 2,000 hours at 105 SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 16Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table.(impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z( 25 ) 1.15 at 100KHz Z(55 )/Z( 25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat ( Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD Фd L α F C s UPS U PART NUMBER SYSTEM P S M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 9

10 UPS Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ΦD L (mm) 100~300KHz (mωmax) Ripple Current 105,100KHz (marms max) Tanδ max Leakage Current (μa max) Part Number 2.5(0E) 4(0G) 6.3(0J) 10(1A) 16(1C) UPS0E561MNN0808U UPS0E681MNN0808U UPS0E821MNN0808U UPS0E821MNN0811U UPS0E102MNN0808U UPS0E102MNN0811U UPS0E122MNN0808U UPS0E152MNN0811U UPS0E152MNN1012U UPS0E182MNN0811U UPS0G471MNN0808U UPS0G561MNN0808U UPS0G681MNN0808U UPS0G821MNN1012U UPS0G122MNN1012U UPS0J221MNN0808U UPS0J331MNN0808U UPS0J391MNN0808U UPS0J471MNN0808U UPS0J561MNN0808U UPS0J681MNN0808U UPS0J821MNN0811U UPS0J821MNN1012U UPS0J102MNN1012U UPS0J152MNN1012U UPS0J202MNN1012U UPS1A271MNN0811U UPS1A471MNN1012U UPS1A561MNN0811U UPS1A561MNN1012U UPS1A681MNN0811U UPS1A821MNN0811U UPS1A821MNN1012U UPS1A102MNN1012U UPS1C151MNN0811U UPS1C181MNN0808U UPS1C181MNN0811U UPS1C271MNN0811U UPS1C331MNN0811U UPS1C331MNN1012U UPS1C471MNN0811U UPS1C471MNN1012U UPS1C821MNN1012U 10

11 UPR Series Super low at a high frequency range High ripple current capability 2,000 hours at 105 SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 16Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD 5 10 Фd L 8 8 α 1 1 F R PART NUMBER SYSTEM U P R M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 11

12 UPR Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ΦD L (mm) 100~300KHz (mωmax) Ripple Current 105,100KHz (marms max) Tanδ max Leakage Current (μa max) Part Number UPR0E221MNN UPR0E331MNN UPR0E561MNN (0E) UPR0E561MNN UPR0E681MNN UPR0E821MNN UPR0E821MNN6308E 4(0G) UPR0G561MNN UPR0J221MNN UPR0J221MNN UPR0J271MNN UPR0J331MNN UPR0J331MNN (0J) UPR0J391MNN UPR0J471MNN UPR0J561MNN UPR0J561MNN UPR0J681MNN UPR0J821MNN UPR1A101MNN UPR1A151MNN (1A) UPR1A221MNN UPR1A271MNN UPR1A331MNN (1C) UPR1C101MNN UPR1C271MNN

13 UL Series Super low at a high frequency range Low profile 6.3x6 max, 8x7 max 2,000 hours at 105 SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 16Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking PART NUMBER SYSTEM ФD Фd L 6 7 F Ф L Ф 2.5 C s UL U L M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 13

14 UL Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 2.5(0E) 6.3(0J) 16(1C) UL0E221MNN UL0E391MNN UL0E561MNN UL0E681MNN UL0J221MNN UL0J331MNN UL1C101MNN UL1C151MNN UL1C181MNN UL1C221MNN UL1C271MNN UL1C331MNN UL1C391MNN UL1C471MNN

15 UPE Series Super low at a high frequency range High ripple current capability 5,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 35Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 5,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead ФD Фd L ~ α F Ф 8Ф Marking E C supe PART NUMBER SYSTEM U P E M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 15

16 UPE Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 2.5(0E) 4(0G) 6.3(0J) 16(1C) 25(1E) 35(1V) UPE0E391MNN UPE0E561MNN UPE0E561MNN UPE0E561MNN UPE0E821MNN UPE0E821MNN UPE0E102MNN UPE0G561MNN UPE0G561MNN UPE0J101MNN UPE0J331MNN UPE0J471MNN , UPE0J561MNN UPE0J821MNN UPE0J821MNN UPE1C101MNN UPE1C101MNN UPE1C181MNN UPE1C181MNN UPE1C181MNN UPE1C221MNN UPE1C271MNN UPE1C271MNN UPE1C271MNN UPE1C331MNN UPE1C471MNN UPE1C471MNN UPE1C471MNN UPE1C561MNN UPE1C821MNN UPE1C102MNN UPE1E560MNN UPE1E820MNN UPE1E181MNN UPE1E331MNN UPE1V220MNN UPE1V330MNN UPE1V820MNN UPE1V121MNN

17 RP Series Low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 16Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD Фd L α F C srp R PART NUMBER SYSTEM P M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 17

18 RP Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 2.5(0E) 4(0G) 6.3(0J) 10(1A) 16(1C) RP0E681MNN RP0E821MNN RP0E152MNN RP0E272MNN RP0G561MNN RP0G821MNN RP0G122MNN RP0J271MNN RP0J471MNN RP0J681MNN RP0J821MNN RP0J102MNN RP0J122MNN RP0J152MNN RP0J152MNN RP1A221MNN RP1A271MNN RP1A331MNN RP1A471MNN RP1A471MNN RP1A561MNN RP1A561MNN RP1A681MNN RP1A681MNN RP1A821MNN RP1A102MNN RP1A122MNN RP1C101MNN RP1C181MNN RP1C181MNN RP1C271MNN RP1C271MNN RP1C271MNN1012R RP1C331MNN RP1C331MNN RP1C331MNN RP1C471MNN RP1C471MNN RP1C561MNN RP1C561MNN RP1C681MNN RP1C821MNN RP1C102MNN

19 RH Series Low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 25Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD 8 10 Фd L α F C s RH PART NUMBER SYSTEM R H M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 19

20 RH Series Voltage (Vdc) 2.5(0E) 4(0G) 6.3(0J) 10(1A) 16(1C) 25(1E) Standard Ratings Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current (marms max) Tan δ max Leakage Current (μa max) Part Number ~ RH0E681MNN RH0E821MNN RH0G561MNN RH0G681MNN RH0G122MNN RH0J471MNN RH0J561MNN RH0J821MNN RH1A121MNN RH1A331MNN RH1A391MNN RH1A561MNN RH1A102MNN RH1C820MNN RH1C151MNN RH1C181MNN RH1C221MNN RH1C271MNN RH1C271MNN RH1C331MNN RH1C391MNN RH1C471MNN RH1C821MNN RH1E121MNN RH1E181MNN

21 GP Series Low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 10 ~ 25Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD Фd 0.6 L α F Ф 8Ф P C s GP PART NUMBER SYSTEM G P M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 21

22 GP Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 10(1A) 16(1C) 25(1E) GP1A471MNN GP1A681MNN GP1A102MNN GP1C101MNN GP1C181MNN GP1C331MNN GP1C471MNN GP1E470MNN GP1E680MNN GP1E101MNN

23 GV Series Low at a high frequency range High ripple current capability High voltage 25~100V 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 25 ~ 100Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD Фd L α F C s GV PART NUMBER SYSTEM G V M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 23

24 GV Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 25(1E) 35(1V) 50(1H) 63(1J) 100(2A) GV1E151MNN GV1E181MNN GV1E181MNN GV1E221MNN GV1E271MNN GV1E331MNN GV1E391MNN GV1E471MNN GV1V180MNN GV1V390MNN GV1V470MNN GV1V820MNN GV1V101MNN GV1V101MNN GV1V121MNN GV1V151MNN GV1V221MNN GV1H270MNN GV1H390MNN GV1H470MNN GV1H680MNN GV1J470MNN GV1J680MNN GV2A180MNN GV2A470MNN

25 GS Series Low at a high frequency range High ripple current capability Large capacitance, size 8x16~10x20 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 16 ~ 25Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Lead Marking ФD 8 10 Фd L 16~20 16~20 α C s GS F PART NUMBER SYSTEM G S M Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 25

26 GS Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number GS1C102MNN0820P GS1C122MNN0820P 16(1C) GS1C152MNN1016P GS1C182MNN1020P GS1C222MNN1020P GS1C272MNN1020P 25(1E) GS1E471MNN0820P 26

27 SG Series Low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 63Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS (mm) Marking Code Case Size ФD L A B C W P ~ ~ ~ ~ ~ ~ ~ Ф 8Ф G C s SG S PART NUMBER SYSTEM G M C B Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 27

28 SG Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number SG0E221MCB SG0E561MCB (0E) SG0E681MCB SG0E152MCB SG0E272MCB SG0G101MCB SG0G151MCB5057 4(0G) SG0G331MCB SG0G681MCB SG0G122MCB SG0J820MCB SG0J101MCB (0J) SG0J221MCB SG0J331MCB SG0J391MCB SG0J821MCB SG1A470MCB SG1A560MCB (1A) SG1A121MCB SG1A271MCB SG1A331MCB SG1A561MCB SG1C330MCB SG1C390MCB SG1C820MCB SG1C101MCB SG1C101MCB (1C) SG1C181MCB SG1C181MCB SG1C271MCB SG1C331MCB SG1C331MCB SG1C561MCB SG1C102MCB (1E) SG1E470MCB SG1V470MCB (1V) SG1V101MCB SG1V221MCB (1H) SG1H101MCB (1J) SG1J220MCB

29 SP Series Super Low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 25Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table.(impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS Marking Code Case Size ФD L A B C W P ~ ~ Ф P ~ ~ ~ Ф C s SP ~ ~ PART NUMBER SYSTEM S P M C B Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 29

30 SP Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number SP0E181MCB SP0E331MCB SP0E331MCB SP0E331MCB6343E SP0E391MCB (0E) SP0E561MCB SP0E561MCB6357E SP0E681MCB SP0E821MCB SP0E102MCB SP0E272MCB1124 4(0G) SP0G331MCB SP0G152MCB SP0J101MCB SP0J121MCB (0J) SP0J221MCB SP0J221MCB SP0J331MCB SP0J471MCB (1A) SP1A331MCB SP1C101MCB (1C) SP1C181MCB SP1C271MCB SP1E470MCB (1E) SP1E101MCB SP1E121MCB

31 SU Series Ultra low at a high frequency range High ripple current capability 2,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 6.3Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 2,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS Code Case Size D L A B C W P ~ ~ ~ Marking 6.3Ф 8Ф U C s SU S PART NUMBER SYSTEM U M C B Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 31

32 SU Series Standard Ratings Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 2.5(0E) 6.3(0J) SU0E331MCB SU0E391MCB SU0E391MCB SU0J331MCB SU0J391MCB

33 SE Series Super low at a high frequency range High ripple current capability 5,000 hours at 105 C SPECIFICATIONS Item Performance Characteristics Category Temperature Range 55 ~ 105 Working Voltage Range 2.5 ~ 35Vdc Surge Voltage Voltage x1.15 Capacitance Tolerance M: ±20% (at 25 and 120Hz) See the standard ratings table (at 25, 100~300KHz) Dissipation Factor (Tanδ) See the standard ratings table (at 25, 120Hz) Leakage Current 1 See the standard ratings table (Impress the rated voltage for 2 minutes) Low Temperature Characteristics Impedance Ratio Z(25 )/Z(25 ) 1.15 at 100KHz Z(55 )/Z(25 ) 1.25 at 100KHz The following specifications shall be satisfied when the capacitors are restored to 25 C after subjected to DC voltage with the rated ripple current is applied for 5,000 hours at 105 C Endurance The following requirements shall be satisfied when the capacitor are restored to 25 after exposing them for 1,000 hours at to 95% RH Damp Heat (Steady State) 1 In case of some problems for measured values, measure after applying rated voltage for 120 minutes at105 C 2 should be measured at both of the terminal ends closest to the capacitor body DIMENSIONS Code Case Size ФD L A B C W P ~ ~ ~ ~ ~ Ф 8Ф Marking E C s SE S PART NUMBER SYSTEM E M C B Special Request Size Code Lead Forming Type Code Capacitance Tolerance Code Capacitance Code Voltage Code Series Code 33

34 SE Series Standard Rating Voltage (Vdc) Capacitance (μf) Case Size ФD L (mm) 100~300KHz (mω max) Ripple Current 105,100KHz (marms max) Tan δ max Leakage Current (μa max) Part Number 2.5(0E) SE0E561MCB6357 4(0G) SE0G561MCB SE0J221MCB (0J) SE0J331MCB SE0J391MCB (1A) SE1A121MCB SE1A271MCB SE1C680MCB SE1C101MCB (1C) SE1C271MCB SE1C271MCB SE1C561MCB SE1C561MCB (1E) SE1E470MCB SE1E101MCB (1V) SE1V121MCB