Series Hydraulic Cable Winches Standard Features. Bloom TM

Size: px

Start display at page:

Download "Series Hydraulic Cable Winches Standard Features. Bloom TM"

Andrea Ball
5 years ago
Views:

operations, flat bed trailers, air freight pullers, rear of cab and front mounting on ½ to 1½ ton trucks.

1 Series 10 HYDRULI L WINHS The rugged construction and versatility of Series 10 makes it adaptable to a wide range of applications. Series 10 direct drive winches are used for industrial pulling and dragging applications including small cranes, rear load waste packers, drill rigs, fishing boats, marine craft, mining and logging operations, flat bed trailers, air freight pullers, rear of cab and front mounting on ½ to 1½ ton trucks. Quality Since UP TO 12,000 POUNDS PITY loom TM GR S WORM SHFT Hydraulic able Winches Standard Features - Special low profile design. Made of high strength cast iron. ompletely sealed for oil enclosed operation and to keep dirt out. - One piece alloy steel hardened and ground for extra durability. WORM GR GR RTIO RINGS DRUM SHFT L DRUM - High tensile aluminum-nickel alloy bronze. Optimum lead and pressure angles transmit maximum power to the drum. - 20:1 standard, :1, 27:1, and 40:1 optional ratios provide optimum efficiency in power and speed. - Worm gear and worm shaft run on tapered roller bearings. Outer end housing has a sealed ball bearing /2 diameter heat -treated alloy steel minimum tensile strength 150,000 psi. - Tough all steel construction resists breakage or warping. UTION: This winch model does not include any kind of holding brake. If your application requires a holding brake choose Lift-Safe winch series LS11H or LS11K with automatic hydraulic safety brakes. RV7/2001

Series 10 Model Selection from Performance Data Quality Since MODL XMPL: 11--L8-20 Gear ase and Shaft Designation 11 = Series 10 with 1-1/2 Drum Shaft Hydraulic Motor Designation,,, DD,, G, 4.9, 6.

2 Series 10 Model Selection from Performance Data Quality Since MODL XMPL: 11--L8-20 Gear ase and Shaft Designation 11 = Series 10 with 1-1/2 Drum Shaft Hydraulic Motor Designation,,, DD,, G, 4.9, 6.2, 8.0, 9.6, 11.9 IS Input Shaft Drum Sizes S8, L8 & XL DRUM PITY Gear Ratio :1, 20:1, 27:1, 40:1 L DIMTR (IN.) DRUM "S8" PITY (FT.) DRUM "L8" PITY (FT.) DRUM "XL" PITY (FT.) 1/ / / / / Special Note. Series 10 winches are available only in low profile mounting - the LP designation is not required. However, it is necessary on all low profile winches to specify whether the winch is to be supplied with angles or less angles.

3 PULL 1ST LYR OF L (LS.) 0 0 Series 10 loom Hydraulic able Winches Model Selection from Performance Data G DD OIL PRSSUR (LS./SQ.IN.) :1 RTIO (optional) L SPD 1ST LYR (FT./MIN.) Quality Since OIL FLOW (GLLONS/MIN.) DD G :1 RTIO (standard) PULL 1ST LYR OF L (LS.) G DD 4.9 L SPD 1ST LYR (FT./MIN.) DD 9.6 G OIL PRSSUR (LS./SQ.IN.) OIL FLOW (GLLONS/MIN.) PULL 1ST LYR OF L (LS.) :1 RTIO (optional) DD G DD 9.6 G 11.9 L SPD 1ST LYR (FT./MIN.) OIL PRSSUR (LS./SQ.IN.) OIL FLOW (GLLONS/MIN.) 40:1 RTIO (optional) PULL 1ST LYR OF L (LS.) 0 L SPD 1ST LYR (FT./MIN.) DD DD OIL PRSSUR (LS./SQ.IN.) OIL FLOW (GLLONS/MIN.)

4 Quality Since Dimensional Drawings Series 10 With S8 and L8 Drum Low Profile Model - Direct Drive

5 Quality Since Dimensional Drawings Series 10 With XL Drum Low Profile Model - Direct Drive

6 10 SRIS MODL SLTION MOTOR 11--S8 11--L8 11--XL 11--XL XL14 MOTOR 11--S8 11--L8 11--XL 11--XL12 1--XL14 MOTOR 11--S8 11--L8 11--XL 11--XL XL14 DD MOTOR 11-DD-S8 11-DD-L8 11-DD-XL 11-DD-XL12 11-DD-XL14 MOTOR 11--S8 11--L8 11--XL 11--XL XL14 G MOTOR 11-G-S8 11-G-L8 11-G-XL 11-G-XL12 11-G-XL MOTOR S L XL XL XL MOTOR S L XL XL XL MOTOR S L XL XL XL MOTOR S L XL XL XL MOTOR S L XL XL XL14 INPUT SHFT MODL 11-IS-S8 11-IS-L8 11-IS-XL 11-IS-XL12 11-IS-XL14

orrect choice of Directional ontrol Valves for loom Winches Tandem enter Spool Valve Work Ports are blocked in neutral position Use on all winches that use motor only to hold load.

7 orrect choice of Directional ontrol Valves for loom Winches Tandem enter Spool Valve Work Ports are blocked in neutral position Use on all winches that use motor only to hold load. *Winches require ridged mounting plate. See owner s manual for information about proper mounting plate thickness or call loom Sales ngineer at factory WRNING! Goods are not intended for use in the moving or lifting of persons! The winches described herein are neither designed nor intended for use or application to equipment used in the lifting or moving of persons and it is understood that all such use shall be at the sole risk of the user. The cable clamps on winches are not designed to hold rated loads. minimum of 5 wraps of cable must be left on drum barrel to guarantee holding of rated load. pplications of winch where life would be endangered by any event are not recommended. LOOM Manufacturing Inc. Winch Division th Street,, Independence, Iowa FX PHON opyright 2015 loom Mfg. Inc.

HYDRAULIC CABLE WINCHES

HYDRAULIC CABLE WINCHES Series 00 Galv Quality Since HYDRULI L WINHS The rugged construction and versatility of Series 00 Galv makes it adaptable to a wide range of applications. Series 00 direct drive winches are used for industrial