Maximum total load rating 70t x 2.3m. rotation radius all 8 wheels 7.19m Name HINO E13C. Engine. Steering Type. Brake. Vehicle mass Total mass

Transcription

1 MODEL RK0 CITY CONSCIOUS CRANE Maximum total load t x 2.3m Crane Main Specifications Crane Performance 9.50m 16.00m 9m 7m 35.25m 38.44m 41.63m Maximum length Hook Max. lifting height above ground Maximum ope radius Rope winding speeds extension speeds raising speeds Rear ends slew radius Slew speeds Crane Major Mechanism Types of boom Types of jib Aux. sheave type system Winding system Slew system 44.81m 4m 7.8m 12.0m Auxiliary sheave 9.50m 4m 7.8m 12.0m Main hook hook Main (high/low) Auxiliary 148sec/38.5m sec/0 º 3,0mm 1.9min- 1 {1.9rpm},000kg x 2.3m (14 loops) 30,000kg x 6.0m (6 loops) 24,000kg x 6.0m (6 loops) 15,000kg x 8.0m (4 loops) 12,000kg x 9.0m (4 loops) 10,000kg x 10.0m (4 loops) 8,000kg x 12.0m (4 loops) 7,500kg x 12.0m (4 loops) 7,500kg x 12.0m (4 loops) 4,120kg x º (1 loop) 2,500kg x º (1 loop) 5,000kg (1 loop) 49.4m 61.3m 34.0m (forward: 40.0m) 37.0m (forward: 42.7m) 187/122m/min (4th layers) 106m/min (2nd layers) Seven-stage box type (2nd to 4th Individually telescopic, 5th, 6th & 7th simultaneous telescopic). Hydraulic telescopic type combined wire rope. Compression truss type, Two-stage box type hydraulic telescopic type. Power set jib, Hydraulic stepless inclined type (5º ~º) Installed on the tip of boom, wind up housing type Double-acting hydraulic cylinder 2 direct pressing type (0~º) Hydraulic motor two independent winch drive planetary gear system with auto brake. (Free fall less) With high speed winding up and down performance. Hydraulic motor planetary gear system Half free / lock changing system, with negative brake Outrigger Extension width 7.6m / 7.2m / 6.6m / 5.6m / 4.3m / 2.m Type Fully hydraulic system, H type Wire Rope For the main IWSC 6XFi(29) Φ 18mmx257m For the aux. IWRC 6XWs(26) c/o Flame resistance Φ 18mmx127m Hydraulic System Hydraulic pump type With two adjustable plungers + Triple gear Hydraulic oil tank capacity 810L Safety Equipment Overload prevention device (Auto-stop), Over winding prevention device (Auto-stop), Slew area limit function, Slew auto-stop device, area limit device, raise / lower gently stop device, Multiple display (inc. Rear side confirmation camera, Drum surveillance camera), Outrigger extension width auto detection device, Slew warning lamp, Slew voice alarm, Passenger port block type lever lock, Check & safety monitor, Hoisting wire latch device, Hydraulic safety valve, extension / retraction security device, extension / retraction order mulfunction auto-stop device, raise / lower security device, Widning up security device, raise / lower security device, Outrigger security device, One-way call, Overload external indicator lamp (cornered polygon), Abnormal winding prevention device (Main/Aux.) Carrier Main Specifications Carrier Performance Max. travelling speed 49km/h Uphill capacity tan θ 0.56 (29º) Min. front 4 wheels 11.2m rotation radius all 8 wheels 7.19m Name HINO E13C Type Inline six-cylinder four-cycle cooling, Direct injection diesel with turbo intercooler Engine Total emission Max. output Max. torque Types of reducer Axle & suspension system L 330kW/1,0min- 1 {448PS/1,0rpm} 1.930N m/1,300min- 1 {197kgf m/1,300rpm} Carrier Major Mechanism Vehicle drive system 6 wheels (8X6) type HST (Hydrostatic transmission) Transmission type with High / Low switch Two-stage reduction gear axle type Floating Hydro-pneumatic suspension type Steering Type Mode Hydraulic power steering, Emergency steering device, With reverse steering correction device Normal (front 4 wheels) / Cramp (8 wheels) / Crab (8 wheels) / Rear (rear 4 wheels) Main brake Penumatioc hydraulic compound 8-wheel disc type Brake Aux. brake Engine exhaust brake and hydraulic brake functions Parking brake Propeller shaft braking internal expansion type (2, 4 axle), with Aux. braking device. Tires 325/95 R24 1/1K Fuel tank capacity 300L Safety Equipment Emergency steering device, Rear steering auto lock, Suspension lock device, Engine overrun warning device, Reverse voice alarm, Left turn voice alarm, Rear, Left side and Left front area confirmation cameras & monitors. Dimensions when Traveling Total length 11,9mm Total width 2,9mm Total height 3,5mm Wheelbase 1,500mm + 3,7mm + 1,500mm Tread Front wheel: 2,590mm / Rear wheel: 2,590mm Front overhang 3,595mm Rear overhang 1,0mm Vehicle mass Total mass 39,945kg Front Front axle: 9,9kg / Front Rear axle: 9,995kg Shaft weight Rear Front axle: 9,995kg / Rear Rear axle: 9,990kg Passenger Capacity 1 person Figures are shown in the international units system SI, however inside of { } are shown in the conventional way.

2 External Dimensions (unit: mm) 4,035 Scale 1/ ,025 ) R2 0,6 0 Slew center 7,0 (Max. extension) us 7,200 (Mid. extension) di 6,0 (Mid. extension) ra 5,0 (Mid. extension) d 2,0 (Min. extension) en 2,9 6 0 R (RS 3,6 3lew 00 6 re 0a 0r 4,300 (Mid. extension) , ,230 1, , , , ,325 1,0 1,500 1,500 3,7 3,595 10,0 11,9 2,5 ~ m foot pin center 2,590 1 RK , , m

3 The chart does not include flexure of the boom and the jib.the chart indicates the range with outrigger maximum extension (all round). The line indicates the ope radius all round when the outriggers are fully extended (7.6m). The dotted line indicates the ope radius at the front when the outriggers are at maximum extension (7.6m). Ope Range Diagram 12.0m offset 5º m offset 25º 12.0m offset 45º 12.0m offset º 5 7.8m offset 5º 7.8m offset 25º 4m m 4m + 7.8m 7.8m offset 45º 7.8m offset º 4m 44.81m Lifting height above ground (m) 41.63m m 35.25m m m m m Ope RK0 2

4 3 RK Main boom / With outrigger Outrigger extension width length (m) Ope Outrigger Max. extension (7.6m) / all round Outrigger Max. extension (7.6m) / forward

5 4 RK Main boom / With outrigger Outrigger extension width length (m) Ope Outrigger Max. extension (7.6m) / rear Outrigger Mid. extension (7.2m) / side

6 R4 R4 Main boom / With outrigger Outrigger extension width length Ope (m) Outrigger Mid. extension (6.6m) / side Outrigger Mid. extension (5.6m) / side Minimum perpendicular passage width Front 4 wheel steering 8 wheel steering Rear 4 wheel steering R4 R 4 R3 R1 R2 R3 R3 R1 R2 B C D B C D R3 R4 R4 C R2 R1 A1 A A2 R1=1m (Min. rotation radius) R2=11.37m (Max. edge of outer ring rotation radius) R3=12.29m (Vehicle rotation radius) R4=12.m ( front edge rotation radius) A=5.98m (Inlet passage width) B=5.98m (Wheel exit passage width) C=6.90m (Vehicle exit passage width) D=7.38m ( front edge exit passage width) R1=7.19m (Min. rotation radius) R2=7.35m (Max. edge of outer ring rotation radius) R3=8.29m (Vehicle rotation radius) R4=8.95m ( front edge rotation radius) A1=4.83m (Wheel inlet passage width) A2=5.m (Vehicle inlet passage width) B=4.83m (Wheel exit passage width) C=5.m (Vehicle exit passage width) D=6.32m ( front edge exit passage width) A1 A2 R1=13.m (Min. rotation radius) R2=13.91m (Max. edge of outer ring rotation radius) R3=14.53m (Vehicle rotation radius) R4=1m ( front edge rotation radius) A1=6.32m (Wheel inlet passage width) A2=6.94m (Vehicle inlet passage width) C=6.94m (Vehicle exit passage width) 5 RK0

7 Main boom / With outrigger Outrigger extension width length (m) Ope Outrigger Mid. extension (4.3m) / side Outrigger Min. extension (2.m)/side Main boom / Without outrigger condition range length Ope (m) Stationary suspension Traveling suspension (less than 2km/h) All round Front All round Front RK0 6

8 Total Load Rating with 44.81m Maximum Outrigger (7.6m) extension / front 44.81m + 7.8m 44.81m m Total Load Rating with 44.81m Maximum Outrigger (7.6m) extension / rear 44.81m + 7.8m 44.81m m RK0

9 Total Load Rating with 44.81m Total Load Rating with 4m Maximum Outrigger (7.6m) extension / front 4m + 7.8m 4m m Maximum Outrigger (7.6m) extension / all round 44.81m + 7.8m 44.81m m RK0 8

10 Total Load Rating with 4m Maximum Outrigger (7.6m) extension / rear 4m + 7.8m 4m m Total Load Rating with 4m Maximum Outrigger (7.6m) extension / all round 4m + 7.8m 4m m RK0

11 Total Load Rating with 44.81m Medium Outrigger (7.2m) extension / all round 44.81m + 7.8m 44.81m m Total Load Rating with 4m Medium Outrigger (7.2m) extension / all round 4m + 7.8m 4m m RK0 10

12 Total Load Rating with 44.81m Medium Outrigger (6.6m) extension / all round 44.81m + 7.8m 44.81m m Total Load Rating with 4m Medium Outrigger (6.6m) extension / all round 4m + 7.8m 4m m RK0

13 Total Load Rating with 44.81m Medium Outrigger (5.6m) extension / all round 44.81m + 7.8m 44.81m m Total Load Rating with 4m Medium Outrigger (5.6m) extension / all round 4m + 7.8m 4m m RK0 12

14 Total Load Rating with 44.81m Medium Outrigger (4.3m) extension / all round 44.81m + 7.8m 44.81m m Total Load Rating with 4m Medium Outrigger (4.3m) extension / all round 4m + 7.8m 4m m Hook dimension & Winding up limit (unit: mm) in holizontal position (t Hook) in holizontal position (30t Hook) in maximum raised position 1, , , , , , , , , t Hook t Hook 490 1, , RK0

15 Notes About The The total load is based on the figures obtained when the crane is horizontally placed on firm ground and the value does not exceed % of the tipping load. Also the value must satisfiy the forward stability in accordance with Article 14 of the mobile crane construction standards. The value includes the mass of hook and hoisting wires. Inside of the bold line the figures are determined by the strength of the machine and the others are determined by the stability of the machine. Even when suspending within the, if there any harmful situations affecting safety such as wind effect, ground states and ope speed, it is the responsibility of the operator to avoid dangerous situations. s cannot be conducted in the parts of the table that are empty. Please be aware that the vehicle will fall even without a load, if the boom is less than the minimum permitted. When a longer than regular boom length is used, use the smaller value for the total load of (either the regular length or one stage upper boom length) to conduct operation. With Outrigger Maximum outrigger extension is 7.6m, medium extension is 7.2m, 6.6m, 5.6m and 4.3m. Minimum extension is 2.m. The lifting performance in the side range will vary depending on the outrigger extension. When the extension widths of left, right, forward, rear sides are different, use the total load table for which ever extension width is smaller. For example, for right side operation, choose the smaller extension width of the right forward or rear outrigger, for left side operation, choose the smaller extension width of the left forward or rear outrigger of the total load. The lifting performance in the forward and rear directions are different to the side range lifting performance with outriggers at maximum extension. When slewing the load from the front or the rear to the side, make sure to use the side range total load. However, the total load for the side range continuously-varies from forward to the sides and rear to the sides and is calculated and displayed by the overload prevention device, except when the outrigger is at minimum extension. 4 5 The total load of the auxiliary sheave is obtained by subtracting the ton hook (490kg) from the boom total load when the boom length is between 9.50m and 16.00m. When the boom length exceeds 16.00m and up to 4m, the 30 ton hook (340kg) weight must be subtracted from the boom s total load.the limit of the total load of the auxiliary sheave is 5,000kg. The total load is obtained by subtracting the hook weights (which shown in the following table) from the individual total load table acording to each operation condition. However, actual lifting load is obtained by further subtracting weights of hoisting wires etc. condition t hook 30t hook 5.0t hook Hoisting wires etc. operation (9.50m~16.00m) operation (from 16.00m up to 4m) Auxiliary sheave operation operation operation, with jib extended Note that for boom operation with the jib extensions, other than those shown in the above table subtracting 3,200kg with 1st stage jib extension and 3,0kg with 2nd stage jib extension. 6 The operation radius is the horizontal distance from the slew center to the center of gravity of the load lifted. 7 The operation radius includes boom flexure so, operate the crane based on this radius. 8 The type of hooks and weights are shown in the follwoing table. Hook type Hook weight t hook 490Kg 30t hook 340Kg 9 The minimum number of loops for a hook should not exceed 5,000kg per wire rope. However, see the following table for the number of loops for each boom length. length Hook type No. of loops length Hook type No. of loops 9.50m 16.00m 9m 7m 35.25m t hook Without Outrigger 1 5.0t hook 130Kg 30t hook 30t hook 30t hook 30t hook m 41.63m 44.81m 4m / Aux. sheave 30t hook 30t hook 30t hook 30t hook 5.0t hook The total load shows the crane capacity or lift performance when it is parked on horizontal and firm ground, the air pressure of the tyres is at the required level (900kPa{kg/cm 2 }) and the suspension lock cylinder is fully retracted. The table also includes the weight of the hook and the wires. The figures inside the bold line are determined by the strength of the machine and those outside the bold line depend on the stability of the machine. Outrigger extension condition Forward range αº Rear range βº Maximum extension (7.6m) Medium extension (7.2m) Medium extension (6.6m) Medium extension (5.6m) Medium extension (4.3m) Minimum extension (2.m) For jib operation, use the boom as a criteria. The ope radius is shown for the case where the boom length is 4m and 44.81with the jib attached. 5 Do not use the auxiliary sheave when the jib is extended. 6 During suspension operations that are oblique in respect to outrigger direction, the symmetry of the side outrigger floats may rise depending on conditions. This does not signify a loss of stability, it is only torsional rigidity or flexure of the carrier frame. Stability is assured for operations within the total load when the crane is horizontally placed on firm ground. An oblique direction (outrigger direction) means from 1 ~ 4 as shown in the diagram below. Forward Rear About 1 This vehicle has an over load prevention device and the total load assumes that the jib is installed under normal ope conditions. Do not blindly remove the jib, because that will reduce the stability. 2 Outrigger extension width and ope range If the the jib is unavoidably detached, always contact the manufacturer. Make sure to submit a notice of change to the Labor Standards Supervision Office once appropriate action has been conducted according to the specification of the manufacturer. 2 The total load s for front lifting ability and side lifting ability are different. Be careful when slewing the load from the front to the side, the crane may become over loaded On tires Stationary Traveling Area αº 1 1 No jib operation can be performed. Use the operation auxiliary parking brake when performing lifting operation while the vehicle is stationary. Set the high/low switch to the low position when lifting while traveling the vehicle. If lifting load while traveling, lower the load close to the ground and drive less than 2km/h of speed. Be careful especially cornering, avoid sudden starts and braking. Do not perform crane operations when traveling with load. RK0 14

16 Standard method (IOS method) / Levers, Pedals layout raise / lower pedal Aux. winding operation pedal Main winding and auxiliary winding levers have a spring return system. The Spring return system is a mechanism to automatically return the levers to the neutral position when they are released.. It is possible to swap the position of the main winding and auxiliary winding levers / operation pedals. raise / lower & extension / retraction lever Slew lever extension / retraction Main winding raise / lower Auxiliary winding Mandatory qualifications for ope and driving Compatible with condition C of the Basic Traffic Conditions Act. when fully equipped. (Registered vehicle weight inspection). When traveling on road, a permit for traveling and a Safety standard mitigation permit are required in accordance with the Road Trucking Vehicle Act. When traveling on road, a vehicle driver's license endorsed for Large sized Special vehicles is required. For crane operation, a Mobile crane operator's license is required. Standard equipment Full power jib Auxiliary sheave ton Hook 30 ton Hook 5.0 ton Ball hook Main/Aux. winch (without free fall) Aluminum outrigger soleplate Electric housing mirror Tool box Centralized lubrication system (slew bearing / carrier / boom raise / lower cylinder) Oil cooler Foot pedals (2) Tachometer Standard accessory tools Supply of Oil tools Intermittent wiper with washer (Front window and skylight) Combined ceiling blinds and sun visor Bending formula operator seat lamp Marker lamp Road side lamp Outrigger control (left side) Green glass Air conditioning (with Defroster) Lunch table Magazine rack Cup holder Ash tray Cigarette lighter Floor mat Hot & cool box Radio (AM / FM) Off-limits rope Tire stopper The actual operation, please follows the Instruction Manual. KOBELCO CRANES CO., LTD. For contact... Tokyo head office/ post code , Higashi Gotanda, Shinagawa-ku, Tokyo Tel: Hokkaido: Tel , Miyagi: Tel , Yokohama: Tel Hokuriku: Tel , Tokai: Tel , Kinki: Tel , Chugoku: Tel , Kyushu: Tel Applicable Model: RK0 RK0SPEC-2 (Specifications are subject to change without notice.) 1101MNF Please read the instruction manual prior to use the vehicle.