Designed to Handle Difficult Fluids

Transcription

1 Designed to Handle Difficult Fluids

2 For Processing Applications with Difficult Fluids Contents Page Introduction...3 Capabilities Overview Flow Capacities & Pressure Ratings...4 Maximum Allowable Solids Guidelines...4 Performance Advantages...6 Industries Served & Fluids Pumped...8 Operating Principle... Pump Models ( & 3 Series) Hose Data... Selection Criteria Pump Models (4 Series) Hose Data Selection Criteria Accessories... 5 Other Wanner Engineering Pumps Due to continuous improvement practices, specifications and other data in this catalog are subject to change.

3 Vector Pumps Handle Aggressive or Corrosive Fluids, Highviscosity Fluids, and Highpurity Solutions Available in 7 models to handle a wide range of processing requirements, Vector peristaltic pumps are ideal for pumping challenging fluids without altering their composition. They move highviscosity (up to, cps) pasty, pulpy, thick, abrasive, and corrosive solutions as well as fluids containing solids up to 3/ inches (9 mm) in size. Vector pumps isolate the fluid being pumped into a single, durable hose so they can handle tough fluids. Design Features Dry pump cavity Selfpriming operation Runs dry without damage Complete isolation of fluid pumped Heavyduty roller bearings Variety of pump configurations, flows, and pressure ratings No dynamic seals, cups or packing to leak or wear Reversible flow Low maintenance Typical Substances Handled Acids Bentonite Slurries Carbon Slurry Ceramic Slip Cosmetics & Creams Dyes & Inks Eggs Ferric Chloride Flavorings Iron Oxide Pigments Jams & Preserves Lime Slurries Paint Sewage Sodium Hydroxide Shampoos Yogurt Typical Industries Served Ceramics Chemical Processing Cosmetics Food & Dairy Processing Marine Mining Paints & Coatings Petrochemicals Pharmaceuticals Pulp & Paper Water & Wastewater Treatment 3

4 Vector Peristaltic Pumps Capabilities Overview Flow Capacities and Pressure Ratings Maximum Maximum Discharge Model Flow (gpm) Pressure (psig) Maximum Allowable Solids Guidelines Maximum Maximum Discharge Model Flow (gpm) Pressure (psig) NonCompressible Solids Sharp Compressible Solids Solids Pump Hose I.D. Size of solids, when percentage Size of solids, when Model (mm) of solids is >5% (mm) percentage is <% (mm) (mm) AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID AVOID

5 Vector pumps are ideal for several applications in production of industrial and commercial paints, coatings, inks, and dyes. 5

6 Vector Pump Performance Advantages Pressure Ratings Up to 8 psig discharge pressure Flow Capacities Up to gpm Contaminationfree Pumping Fluid is contained in the hose and only contacts the hose Fluid/Hose Compatibility Fiberbraided or extruded hoses can handle abrasive or corrosive fluids as well as food products or pharmaceutical materials Lowshear/Nonemulsifying Transfers food and pharmaceutical solutions without crushing or foaming the fluids Selfpriming Requires no priming chamber; suction lifts to 9/ feet depending on model Dry Running Externally lubricated hose enables the pumps to run dry without stalling or damaging the hose or roller assembly; avoids pump failure and reducing pump life Dependable Sealless Design No dynamic seals or packing that can leak, clog, wear out, or need replacement Handles Abrasive Solids Can pump abrasive fine particles and solids up to 3/ inches (9 mm) Easy to Clean Reversible rotary movement provides for easytoclean system piping; flushing may be eliminated Easy to Service Simple replacement of hoses saves time; clear plastic cover allows the pump to be checked easily during operation for any problems Vacuum Capability A Vector pump can be used as a vacuum pump and for cleaning up spills; evacuates gases as well as fluids Dosing Capability A Vector pump is also a positive displacement pump for metering; output flow is directly proportional to pump speed 6

7 Expensive chemicals and compounds, including adhesive resins, polymers, and latex are protected by Vector pumps during processing. 7

8 Industries Served and Fluids Pumped Vector peristaltic pumps can handle the most difficult process fluids to serve a wide range of commercial, institutional, industrial, and municipal markets. Examples of many successful applications are listed in this section but these are not limitations. If you have a difficult fluid to process not listed, contact Wanner Engineering for application assistance. Building & Construction Adhesives, dyes, glues, grout, iron oxide pigments, paints, plaster, pottery, tile Ceramic & Glass Clay slips, dyes, enamels, glazes, grinding water, grout, quartz paste, silicon Chemical Processing Abrasive mixes, acids, adhesive resins, caustic soda, detergent paste, latex, pigments, polyester mixes, polymers Distilleries Alcohol, spices, spirits Electrical Polyester slurries for insulating wire Food & Beverage Processing Bentonite and carbon slurries, butter, cake dough, cake frosting, caramel, chocolate, cream, egg yolks with whites, fats, flavorings, fruit juices, gelatins, ice cream, jams and preserves, milk, mustard, potato waste, syrups, tomato sauce, water and salt mixtures, yeast solution, yogurt Marine Sewage, wastewater, solid waste Meat Processing Acids, animal and waste blood, hair and bone mixtures Medical, Pharmaceutical & Cosmetics Face creams, latex, lotions, plasma, protein solutions, shampoo, vaccines, Vaseline Mining, Tunneling & Quarrying Coal, copper and platinum slurries Photographic Acids, diluents, thinners Pulp & Paper Abrasive, fibrous fluids, aluminum sulfate, boiler wastewater, caustic soda (lye), cold seal, dyes, hydrochloric acid, inks, prepaint coatings, sulfuric acid Tanneries Acids, dyes, ferrous sulfate, waste fluids with solids Textile Manufacturing Acids, adhesives, bleach, dyes, sizing Water & Wastewater Treatment Acids, activated carbon, aluminum sulfate, caustic soda (lye), ferrous chloride, flocculants, foam inhibitors, lime slurries, solid waste 8

9 Activated carbon, aluminum sulfate, flocculants, slurries, and solid wastes found in water and wastewater treatment applications are handled easily by Vector pumps. 9

10 Vector Peristaltic Pump Operating Principle Peristaltic pumps work by compressing and relaxing a hose positioned between a rotating device and a circular pump housing. Vector Series pumps use rotating rollers that provide the same push with far less hose wear. The peristaltic method employed in Vector pumps can create % compression at all times. As a result, there is virtually no slipping. Metering is highly accurate. Up to 9/ feet of suction lift is produced. Despite this powerful pumping action, Vector pumps will not cause frothing or delicate emulsions to break up. Since fluids travel through a single hose, they never come into contact with moving valves, springs, or seals. This makes Vector pumps ideal for handling abrasive, shearsensitive, or corrosive fluids. Dyes, thick fluids, and solids up to 3/ inches (9 mm) are also readily pumped.

11 Superior Roller Design Fluid positioned ahead of the rollers gets pushed forward as the rollers rotate inside of the case. Vector uses an evolutionary roller mechanism instead of a rigid shoe to push fluids through its hose. This ensures longer working life with less downtime for maintenance. The rollers generate less friction than shoes, extending hose life and reducing downtime. Meanwhile, the portion of the hose just behind the rollers rebounds to create a vacuum. The vacuum draws fluid into the pumping hose, which is then pushed forward by the rollers.

12 Vector Pumps Hose Data ( & 3 Series) Construction Extruded: 7 hours Typical Life at 3 rpm Preferred when: Pumping foods and pharmaceuticals Clean fluids Lower pressures required (max. 3 psig) Fiber Braided: 5 hours Typical Life at 3 rpm Preferred when: Pumping fluids with abrasives The pump is required to create a strong vacuum High pressures are required Operating Duty Intermittent: (One hour stop after hours in use) Higher pressures and higher pump speed Continuous: Dimensions A Low pressures and lower speed (mm) A B C C B Hose Identification Extruded Code Hypalon HE Black color, shinny smooth surface Neoprene PE Flat black color, rough surface, rubber smell Varprene VE Cream, smooth surface Silicone SE Rust color, smooth surface Pharmed FE Cream color, Pharmed name on hose Fiber Braided Hypalon HF Black color, yellow or blue stripe, double braided EPDM EF Black color, white stripe, double braided Natural Rubber NF Black color, green stripe, double braided (standard duty) Natural Rubber MF Black color, no stripes, thick double braids (heavy duty) Nitrile Rubber BF Black color with white inner hose. Nitrile Rubber, Oilrated OF Black color with HBRFHYK stamped on hose. Material Operating Temperatures Industry Approvals EPDM Hypalon Neoprene Silicone 3 to 85 F ( to 85 C) 3 to 8 F ( to 8. C) 5 to 3 F ( to 54.4 C) 4 to 85 F ( to 85 C) Varprene 4 to 85 F ( to 85 C) Meets FDA Criteria Natural Rubber 4 to 85 F ( to 85 C) Meets FDA Criteria Nitrile Rubber 3 to 6 F (5 to 7. C) Pharmed 3 to 8 F ( to 8. C) Meets USP Class VI, FDA, and NSF Criteria Natural rubber heavy duty hose meets FDA criteria. Pharmed Reg. SaintGobain Performance Plastics ATTENTION! When operating within 5 F (9.4 C) of maximum hose temperature, do not exceed rpm pump speed. In addition, metal inspection plate is required vs. clear plastic material.

13 Vector Pumps Selection Guidelines ( & 3 Series). Collect application information Fluid: Discharge Press: psig Suction Condition: Lift: feet or Vacuum: inches of Hg or Flooded: feet of fluid above pump or Pressurized: psig Flow or Flow Range: gpm Temperature ( F): Min: Max: Normal: Solids?, describe: Solid Size: Solid Length: Solids %: Viscosity at Temp: Vapor Pressure at Temp: Specific Gravity: Duty Cycle (hrs/day): Motor Enclosure: Hertz: 5 6 Volts: Phase: 3 Motor eff: Std High Inverter Duty Variable Frequency Drive: Yes No If yes, what environment will controller be mounted: Inside another panel Dry, fairly dust free Dusty area Wet area Wash down area Hazardous area If yes, class and group If Yes, input voltage: Determine the maximum roller speed Duty Cycle (hours/day) of operation <8 hours/day: the pump can be run out of the gray shaded areas on the pump specification curves (minimum of hour stop after hours use). 8 hours/day: do not operate out of the gray shaded areas on the pump specification curves. > hours/day: 53 rpm is the maximum recommended speed. Viscosity of the fluid < cps: no speed correction needed cps: max. speed 4 rpm, 5 cps: max. speed 3 rpm; use flooded/pressurized suction 5,, cps: max. speed rpm; use flooded/pressurized suction,5, cps: max. speed rpm; use flooded/pressurized suction Note: With viscosities over cps it is very important to oversize the suction line / to times the pump connector size and to keep suction lines as short as possible. Temperature of the fluid: If the fluid temperature pumped is within 5 F (9.4 C) of the maximum temperature rating of the hose, contact factory and select a pump with a maximum speed of rpm. 3. Pump Selection Select pump that can deliver the required flow based on the maximum roller speed and discharge pressure required by the application. Note: It may be required to select a larger pump if solids are larger than the maximum size the pump can handle. 4. Hose Selection Hose selection based on chemical compatibility and temperature. For suction vacuum over 4.5" Hg, always use fiber braided hoses (extruded hoses may collapse) In general, fiberbraided hoses will last longer and withstand greater discharge pressures than extruded hoses. Maximum recommended motor speeds with extruded hoses 4 rpm. Note: Maximum viscosity for Nitrile hose is 3 cps. (The inner white hose will separate from the outer black hose.) 5. Connector Type and Material Selection 6. Drive Selection 3

14 MODEL PUMP DATA Performance.5 (3 PSI) Gallons Per Minute.5.6 Horsepower Revolutions Per Minute 4 6 Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: /4 inch (6.3 mm) max. Specifications Discharge Pressure: 3 psig ( bar) max. Suction Lift: 7 ft (. m) Suction Pressure: 5 psig ( bar) max. Horsepower:* /4 max. Hose Size: 9 x 6 x 33 mm Displacement:.44 gal/rev Weight (pump only): 6.5 lbs (3 kg) Weight (with drive): 5. lbs (7 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Plastic/Alloy Wetted Parts Hose: EXTRUDED Neoprene, Hypalon, Varprene, PharMed BRAIDED Natural Rubber, EPDM Inlet/Outlet Connections: PTFE, Brass or Stainless Steel Hose Barb, Brass NPT, and Stainless Steel Sanitary Triclamp 4

15 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation Model Shaft Drive Pump ) 4X Ø.6 (6.5).8 () 4.3 () 4. (4). (5). (6) 4.3 () 4.5 (4) 6.3 (6) 6. (56) 5.8 (48) 6.7 (7) 4X Ø.6 (6.5).8 ().4 (3.5).3 (7).8 () 56 Hose Material/Type FE PharMed, extruded () HE Hypalon, extruded NF Natural Rubber, fiberbraided EF EPDM, fiberbraided PE Neoprene, extruded VE Varprene, extruded 78 Connector Material/Style AA PTFE, /" hose barb CC 36 SST, Sanitary, 3/4" triclamp FF Brass, 3/8" hose barb GG Brass, 3/8" male NPT SS 36 SST, 3/8" hose barb TT 36 SST, 3/8" male NPT 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig Ø, /4 BHP TEFC, 53 VAC, 6 Hz B. 7: 4 3 D. 6: 8 3 F.9 4: 43 3 H.5 3: 57 J.3 : Ø, /4 BHP TEFC, 346 VAC, 6 Hz 3: Constant Torque Speed Range L. 7: 4 3 N. 6: 8 3 P.9 4: 43 3 R.5 3: 57 V.3 : 86 7 A No Drive Meets FDA and NSP for food handling. Maximum pressure: 3.5 psig. 5

16 MODEL 3 PUMP DATA Performance.5 (3 PSI).5.5 Gallons Per Minute Horsepower Revolutions Per Minute 4 6 Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 7/6 inch ( mm) max. Specifications Discharge Pressure: 3 psig ( bar) max. Suction Lift: ft. (3 m) Suction Pressure: 5 psig ( bar) max. Horsepower:* /4 max. Hose Size: 3 x x 39 mm Displacement:. gal/rev Weight (pump only): lbs. (4.5 kg) Weight (with drive): 9.8 lbs. (9 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Plastic/Alloy Wetted Parts Hose: EXTRUDED Hypalon, Varprene, Silicone, PharMed BRAIDED Natural Rubber, EPDM Inlet/Outlet Connections: PTFE, Brass or Stainless Steel Hose Barb, Brass NPT, and Stainless Steel Sanitary Triclamp 6

17 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model 3 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 3 Model 3 Shaft Drive Pump ) 4X Ø.6 (6.5).8 () 5. (7) 5. (3).6 (66). (6) 5. (7) 4.9 (6) 7. (8) 6. (56) 6.6 (68) 6.7 (7) 4X Ø.6 (6.5).8 ().4 ().3 (7).9 (4) 56 Hose Material/Type FE PharMed, extruded () HE Hypalon, extruded NF Natural Rubber, fiberbraided EF EPDM, fiberbraided SE Silicone, extruded VE Varprene, extruded 78 Connector Material/Style AA PTFE, 3/4" hose barb CC 36 SST, Sanitary, 3/4" triclamp FF Brass, /" hose barb GG Brass, /" male NPT SS 36 SST, /" hose barb TT 36 SST, 3/4" male NPT 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig Ø, /4 BHP TEFC, 53 VAC, 6 Hz B.6 7: 4 3 D.3 6: 8 3 F.47 4: 43 3 H.6 3: 57 J.94 : Ø, /4 BHP TEFC, 346 VAC, 6 Hz 3: Constant Torque Speed Range L.6 7: 4 3 N.3 6: 8 3 P.47 4: 43 3 R.6 3: 57 V.94 : 86 7 A No Drive Meets FDA and NSP for food handling. Maximum pressure: 3.5 psig. 7

18 MODEL 4 PUMP DATA Performance 4. (45 PSI) Gallons Per Minute..5 Horsepower Revolutions Per Minute 4 Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: /6 inch (7.4 mm) max. Specifications Discharge Pressure: 45 psig (3 bar) max. Suction Lift: 4 ft. (4.3 m) Suction Pressure: 8 psig (. bar) max. Horsepower:* /3 max. Hose Size: 7 x 3 x 59 mm Displacement:.86 gal/rev Weight (pump only): lbs. (9 kg) Weight (with drive): 34 lbs. (5.5 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Plastic/Alloy Wetted Parts Hose: EXTRUDED Neoprene, Hypalon, Varprene, Silicone BRAIDED Natural Rubber, EPDM, Nitrile Rubber Inlet/Outlet Connections: PTFE or Stainless Steel Hose Barb, Stainless Steel or Carbon Steel ANSI Flange, Brass or Carbon Steel NPT, and Stainless Steel Sanitary Triclamp 8

19 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model 4 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4X Ø.6 (6.5) 6.6 (67) 7.4 (88) 3.7 (94) 6.6 (67).3 (7.5) 7.4 (87) 9.3 (35) 7. (8) 8.7 () 7.9 () 4X Ø.6 (6.5).5 (3.5).4 ().3 (3) 4 Pump Designation 4 Model 4 Shaft Drive Pump 56 Hose Material/Type EF EPDM, fiberbraided HE Hypalon, extruded MF Natural Rubber, fiberbraided, heavyduty NF Natural Rubber, fiberbraided PE Neoprene, extruded SE Silicone, extruded OF Nitrile, Oilrated, fiberbraided, heavyduty VE Varprene, extruded 78 Connector Material/Style AA PTFE, " hose barb CC 36 SST, Sanitary, " triclamp EE Carbon Steel, 3/4" male NPT FF Brass, 3/4" hose barb GG Brass, 3/4" male NPT SS 36 SST, 3/4" hose barb TT 36 SST, 3/4" male NPT 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, /3 BHP TEFC, 3/46 VAC, 6 Hz : Constant Torque Speed Range B.49 : 7. 3(45) D.69 7: 4 3(45) F.86 6: 3 3(45) H. 46: (45) J.43 35: 5 5(3) L.75 8: 6 (5) N.5 : 88 8() A No Drive ( ) Heavyduty, fiberbraided hose Note: Ø motors also available. Contact Wanner Engineering. 9

20 MODEL 5 PUMP DATA Performance 9. (5 PSI) Gallons Per Minute Horsepower 4 6 Revolutions Per Minute 8 Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: /4 inch (3.7 mm) max. Specifications Discharge Pressure: 5 psig (3.4 bar) max. Suction Lift: 6.5 ft. (5 m) Suction Pressure: 5 psig (.7 bar) max. Horsepower:* 3/4 max. Hose Size: 5 x 43 x 86 mm Displacement:.85 gal/rev (.3 l/rev) Weight (pump only): 4 lbs. (8 kg) Weight (with drive): 83 lbs. (38 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Aluminum Alloy Wetted Parts Hose: EXTRUDED Neoprene, Varprene BRAIDED EPDM, Hypalon, Nitrile Rubber, Natural Rubber (regular and heavyduty) Inlet/Outlet Connections: PTFE or Stainless Steel Hose Barb, Stainless Steel or Carbon Steel ANSI Flange, PTFE NPT, and Stainless Steel Sanitary Triclamp

21 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model 5 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number (44) X Ø.43 ().4 6) 8.6 (8) 8.6 (8). (56) 5. (8).4 ().8 (75) 5.7 (4) 7.3 (44).3 (6) 9.4 (4) 4X Ø.43 ().4 (36).7 (8).8 ().7 (44) Order Order Digit Code Description 4 Pump Designation 5 Model 5 Shaft Drive Pump 56 Hose Material/Type 8.6 EF EPDM, fiberbraided (8) HF Hypalon, fiberbraided MF Natural Rubber, fiberbraided, heavyduty (5 psig max.).7 NF Natural Rubber, fiberbraided (8) OF Nitrile, Oilrated, fiberbraided, heavyduty (5 psig.8 max.) () PE Neoprene, extruded (3 psig max.) VE Varprene, extruded (3 psig max.) 78 Connector Material/Style AA PTFE, /4" hose barb BB 36 SST, " ANSI flange CC 36 SST, Sanitary, /" triclamp EE Carbon Steel, " male NPT HH PTFE, " male NPT SS 36 SST, " hose barb 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, / BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range B.7 85: 37(5) D.5 56: 3 37(5) F 3. 45: 38 37(45) H : 46 37(43) 3Ø, 3/4 BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range J 5.9 4: 7 9 (3) A No Drive ( ) Heavyduty, fiberbraided hose

22 MODEL 35 PUMP DATA Performance HP 8 h.5 psig 4 psig psig 7 psig.75 4 h GPM RPM Fluid Characteristics Viscosity: Liquid Temperature:, cps max. 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: Specifications Discharge Pressure: 4 inch ( mm) max. psig (3.8 bar) max. Suction Lift: ft. (6.7 m) Suction Pressure: Horsepower:* Hose Size: Displacement: Lubrication Fluid: Weight (pump only): Weight (with drive): psig (.4 bar) max. max. 5 x 44 x 85 mm.79 gal/rev (.3 l/rev) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details..6 quarts max. 77 lbs. (35 kg) 76 lbs. (8 kg) Materials of Construction Nonwetted Parts Casing: Aluminum Rotor: Cast Iron Rollers: Steel Roller Holders: Cast Iron Frame: Steel Wetted Parts Hose: FIBER BRAIDED EPDM, Hypalon, Nitrile Rubber, Natural Rubber Inlet/Outlet Connections: PVC, Carbon Steel, and Stainless Steel

23 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model 35 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number X Ø.55 (4) 9.8 (5) 8.9 (5) 4.4 (.5).6 (5). (39).8 (35).6 (95) 4X Ø.55 (4). (54).4 (9) Order Order Digit Code Description 4 Pump Designation 35 Model 35 Shaft Drive Pump 56 Hose Material/Type EF EPDM, fiberbraided ( psig max.) HF Hypalon, fiberbraided ( psig max.) MF Natural Rubber, fiberbraided, heavyduty ( psig.4max.) (9) NF Natural Rubber, fiberbraided ( psig max.) OF 8.9 Nitrile, Oilrated, (48) fiberbraided, heavyduty ( psig max.) 78 Connector Material/Style.5 (5) EB Carbon Steel, /4" hose barb EE Carbon Steel, /4" male NPT PV PVC, /4" hose barb TT 36 SST, /4" MNPT SS 36 SST, /4 hose barb 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, 3/4 BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range B.3 9: 9 () D.7 69: 5 75 () 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range F.8 43: 39 5 () 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range H 5.7 : 78 ().8 () 8.9 (48).5 (5) J 7.6 7: 75 () L 9. 4: 3 5 () A No Drive ( ) Fluid Viscosity Pressure Range 5 cps 75 psig 5, cps psig 3

24 MODEL 6 PUMP DATA Performance (6 PSI) 5. Gallons Per Minute..5 Horsepower Revolutions Per Minute Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 7/8 inch (47.6 mm) max. Specifications Discharge Pressure: 6 psig (4. bar) max. Suction Lift: 4 ft. (7.3 m) Suction Pressure: 5 psig (.7 bar) max. Horsepower:* max. Hose Size: 3 x 55 x 5 mm Displacement:.8 gal/rev Weight (pump only): 95 lbs. (43 kg) Weight (with drive): 7 lbs. (78 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Aluminum Alloy Wetted Parts Hose: EXTRUDED Neoprene, Varprene, Silicone BRAIDED EPDM, Hypalon, Nitrile Rubber, Natural Rubber (regular and heavyduty) Inlet/Outlet Connections: PTFE or Stainless Steel Hose Barb, Stainless Steel or Carbon Steel ANSI Flange, PTFE NPT, and Stainless Steel Sanitary Triclamp 4

25 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes.. (55) 3.6 (345) 8.9 (6) Model 6 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number (66) Order Order Digit Code Description 4.3 (364) 5.8 (48).4 (57) 3. (59) 3. (33) 5. (38).47 () 4X Ø.55 (4).6 (66).9 (556) 4 Pump Designation 6 Model 6 Shaft Drive Pump 56 Hose Material/Type EF EPDM, fiberbraided HF Hypalon, fiberbraided MF Natural Rubber, fiberbraided, heavyduty (6 psig max.) NF Natural Rubber, fiberbraided PE Neoprene, extruded (3 psig max.).47 () SE Silicone, extruded (3 psig max.) OF Nitrile, Oilrated, fiberbraided, heavyduty (6 psig max.) VE.4 Varprene, extruded (3 (57) psig max.) 78 Connector Material/Style 3. (59) AA PTFE, /4" hose barb BB 36 SST, /4" ANSI flange CC 36 SST, Sanitary, /" triclamp DD Carbon Steel, /4" ANSI flange EE Carbon Steel, /" male NPT HH PTFE, /4" male NPT TT SST /" NPT SS 36 SST, /4 hose barb 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range B 3.5 9: 9 45(6) 3Ø, / BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range D : 7 45(6) F 7. 43: 4 45(6) 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range H.3 3: 57 35(45) J 4. : 78 35(45) A No Drive.9 (556) ( ) Heavyduty, fiberbraided hose 5

26 MODEL 7 PUMP DATA Performance 5. ( PSI) Gallons Per Minute 5.. Horsepower Revolutions Per Minute 8 Fluid Characteristics Continuous Duty (8 hrs/day) Viscosity: 5, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 3/8 inch (6 mm) max. Specifications Discharge Pressure: psig (7 bar) max. Suction Lift: 4 ft. (7.3 m) Suction Pressure: 5 psig (.7 bar) max. Horsepower:* 3 max. Hose Size: 45 x 75 x 455 mm Displacement:.5 gal/rev Weight (pump only): 85 lbs. (84 kg) Weight (with drive): 75 lbs. (5 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Aluminum Alloy Wetted Parts Hose: EXTRUDED Varprene BRAIDED EPDM, Hypalon, Nitrile Rubber, Natural Rubber (regular and heavyduty) Inlet/Outlet Connections: PTFE or Stainless Steel Hose Barb, Stainless Steel or Carbon Steel ANSI Flange, PTFE NPT, and Stainless Steel Sanitary Triclamp 6

27 Dimensional Drawings Inches (mm) (87) (455) See Ordering Information for motor and gearbox sizes..3 (87) 6.5 (4) 6.5 (4) 5.6 (65) 3. (793) 7.9 (455) 7. (438) 6.5 (66) 7. (438) Order Order 6.5 Digit Code Description (67) 4 Pump Designation 7 Model 7 Shaft Drive Pump 56 Hose Material/Type 6.5 EF EPDM, fiberbraided 6.5(67) (66) HF Hypalon, fiberbraided MF Natural Rubber, fiberbraided, heavyduty ( psig max.) NF Natural Rubber, fiberbraided OF Nitrile, Oilrated, fiberbraided, heavyduty ( psig max.) VE Varprene, extruded (3 psig max.) 78 Connector Material/Style AA PTFE, " hose barb (6 psig max.) BB 36 SST, " ANSI flange CC 36 SST, Sanitary, " triclamp DD Carbon Steel, " ANSI flange EE Carbon Steel, " male NPT HH PTFE, " male NPT (6 psig max.) SS 36 SST,.5" hose barb.6 (4) Model 7 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, / BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range B 7. : 4 45() D.5 8: 45() 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range F : 3 45() H.4 43: 4 45(8) J : 5 4(6) 3Ø, 3 BHP TEFC, 346 VAC, 6 Hz 3: Constant Torque Speed Range L 4.5 : 8 35(45) A No Drive ( ) Heavyduty, fiberbraided hose (65).6 (4) 7

28 MODEL 8 PUMP DATA Performance 7 ( PSI) Flow 7 Gallons Per Minute 4 3 BHP Horsepower Revolutions Per Minute Continuous Duty (8 hrs/day) 7 8 Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 36 inch (94 mm) max. Specifications Discharge Pressure: psig (7 bar) max. Suction Lift: 4 ft. (7.3 m) Suction Pressure: psig (.4 bar) max. Horsepower:* max. Hose Size: 55 x 9 x 85 mm Displacement:.5 gal/rev Lubrication Fluid: 4 gal max. Weight (pump only): 59 lbs. (4 kg) Weight (with drive): 739 lbs. (336 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Steel Wetted Parts Hose: BRAIDED Hypalon, EPDM, Natural Rubber (regular and heavyduty), Oilrated Nitrile Inlet/Outlet Connections: Stainless Steel Flange, Carbon Steel NPT, Stainless Steel NPT, Nylon NPT, Polypropylene NPT 8

29 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. 4. (4) 7.4 (697) Model 8 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 9.5 (494).8 (57) 9. (3) ANSI 5 3" 4 Holes Ø.7 (8)..8 (58) (3) 4.8 (377) 5. (64) 37.4 (95) approx. 4.7 () 35. (888) 9.5 (494). (3) 4 Pump Designation 8 Model 8 Shaft Drive Pump 56 Hose Material/Type EF EPDM, fiberbraided (75 psig max.) HF Hypalon, fiberbraided (75 psig max.) MF Natural Rubber, fiberbraided, heavyduty ( psig max.) NF Natural Rubber, fiberbraided (75 psig max.) OF Oilrated Nitrile, fiberbraided, heavyduty ( psig max.) 78 Connector Material/Style BB 36 SST, 3" ANSI flange EE Carbon Steel, 3" male NPT NN Nylon, 3 male NPT ( F max.) PP Polypropylene, 3 male NPT (85 F max.) TT 36 SST, 3" male NPT 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 346 VAC, 6 Hz 4: Contstant Torque Speed Range B 6 83: () 5 D 3 6: 9 () 5 F 8 48: 36 () 5 H 3 4: 4 () 5 J 36 37: 47 () 5 L 5 7: 64 9 () 7.5 A No Drive ( ) Fluid Viscosity Pressure Range 5 cps 75 psig 5, cps psig 7 (8). (3).6 (4) 3.3 (77) 33.5 (85).3 (34).6 (4) 9

30 MODEL 9 PUMP DATA Performance 4 8 ( PSI) Flow 6 4 Gallons Per Minute 8 6 BHP 8 Horsepower Revolutions Per Minute Continuous Duty (8 hrs/day) 7 8 Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 36 inch (94 mm) max. Specifications Discharge Pressure: psig (7 bar) max. Suction Lift: 4 ft. (7.3 m) Suction Pressure: psig (.4 bar) max. Horsepower:* 8 max. Hose Size: 75 x x 4 mm Displacement:.5 gal/rev Lubrication Fluid: 8.5 gal max. Weight (pump only): 88 lbs. (4 kg) Weight (with drive):,3 lbs. (55 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing: Aluminum Alloy Rotor: Aluminum Alloy Rollers: Steel Wetted Parts Hose: BRAIDED Hypalon, EPDM, Natural Rubber (regular and heavyduty), Oilrated Nitrile Inlet/Outlet Connections: Stainless Steel Flange, Stainless Steel NPT, Carbon Steel NPT, Nylon NPT 3

31 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. 5.9 (38) 34.8 (883) Model 9 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 6.7 (678) 9.5 (4) ANSI 5 4" 4 Holes Ø.98 (5) (676) (35). (5) 9.4 (756) 43.5 (5) approx. 6.3 (6).8 (58).4 (35) 4. (77) 4 Pump Designation 9 Model 9 Shaft Drive Pump 56 Hose Material/Type EF EPDM, fiberbraided (75 psig max.) HF Hypalon, fiberbraided (75 psig max.) MF Natural Rubber, fiberbraided, heavyduty ( psig max.) NF Natural Rubber, fiberbraided (75 psig max.) OF Oilrated Nitrile, fiberbraided, heavyduty ( psig max.) 78 Connector Material/Style BB 36 SST, 4" ANSI flange EE Carbon Steel, 4" male NPT NN Nylon, 4" male NPT ( F max) TT 36 SST, 4 male NPT 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 346 VAC, 6 Hz 4: Contstant Torque Speed Range B 4 79: () 7.5 D 57 6: 9 () 7.5 F 73 48: 37 () 7.5 H 84 4: 43 () J 97 35: 49 () L 8: 63 9 () 5 A No Drive ( ) Fluid Viscosity Pressure Range.8 (58) 5 cps 75 psig 5, cps psig.98 (5).4 (35).77 (45) 35.8 (9) 39.4 ().5 ().8 (45) 3

32 MODEL PUMP DATA Performance 3 (6 PSI) 5 Gallons Per Minute Horsepower Revolutions Per Minute 5 Continuous Duty (8 hrs/day) Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 36 inch (94 mm) max. Specifications Discharge Pressure: 6 psig (8 bar) max. Suction Lift: ft. (7.3 m) Suction Pressure: psig (.4 bar) max. Horsepower:* max. Hose Size: x 44 x 35 mm Displacement: 5.8 gal/rev Lubrication Fluid: 5.85 gal max. Weight (pump only):,984 lbs. (9 kg) Weight (with drive):,535 lbs. (,5 kg) * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Materials of Construction Nonwetted Parts Casing & Front Cover: Cast Iron Rotor Assembly: Aluminum Rollers: Aluminum Wetted Parts Hose: FIBER BRAIDED EPDM, Hypalon, Nitrile Rubber, Natural Rubber (regular and heavyduty) Inlet/Outlet Connections: Carbon Steel ANSI Flange, Nylon & PVC NPT 3

33 Dimensional Drawings Inches (mm) See Ordering Information for motor and gearbox sizes. Model Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number (48) 3.6 (346).3 7). (5) 3 ) f..4 (6). (5) Ø.6 (7) (x) 34.7 (88) 38.6 (98) 6.6 (589.5) Ref. 55. (4) 59. (5) 63.7 (67) Ref (87) 6.3 (6) Ref.. (5) 6.6 (564) Order Order Digit Code Description 4 Pump Designation Model Shaft Drive Pump 56 Hose Material/Type BS Oilrated Nitrile, fiberbraided EF EPDM, fiberbraided HS Hypalon, fiberbraided (7 psig max.) MS Natural Rubber, fiberbraided 78 Connector Material/Style DD Carbon Steel, 6 ANSI flange NN Nylon, 5 ANSI flange ( F/93.3 C max.) PP PVC, 5 ANSI flange (76 F/8 C max.) 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig 3Ø, BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range B 5 74: 6 () F 79 4: 5 6 () 3Ø, 5 BHP TEFC, 346 VAC, 6 Hz 4: Constant Torque Speed Range G 4 89: 6 () M 53 59: 9 6 () 3Ø, BHP TEFC, 346 VAC, 6 Hz 3: Constant Torque Speed Range T 44: 4 () A No Drive ( ) Fluid Viscosity Pressure Range 5 cps 75 psig 5, cps 6 psig 33

34 Vector Pumps Hose Data (4 Series) Construction Fiber Braided: 5 hours Typical Life at 3 rpm Preferred when: Pumping fluids with abrasives The pump is required to create a strong vacuum High pressures are required Hose Identification Fiber Braided (Polyamide) to 6 Layers Code Natural Rubber MF White stripe NBR, Oilrated BF Yellow stripe Nitrile Rubber Food Grade (NBRF) YF White & yellow stripe EPDM EF Red stripe Hypalon HF Blue stripe Operating Duty Intermittent: Higher pressures and higher pump speed Continuous: Low pressures and lower speed Dimensions A B C Material Operating Temperatures Industry Approvals Natural Rubber 68 F to 76 F ( C to 8 C) NBR 5 F to 76 F ( C to 8 C) NBR Food Grade 5 F to 76 F ( C to 8 C) Meets FDA Criteria EPDM 68 F to 76 F ( C to 8 C) Hypalon 68 F to 76 F ( C to 8 C) (mm) A B C ATTENTION! When operating within 5 F (9.4 C) of maximum hose temperature, do not exceed rpm pump speed. In addition, metal inspection plate is required vs. clear plastic material. 34

35 Vector Pumps Selection Guidelines (4 Series). Collect application information Fluid: Discharge Press: psig Suction Condition: Lift: feet or Vacuum: inches of Hg or Flooded: feet of fluid above pump or Pressurized: psig Flow or Flow Range: gpm Temperature ( F): Min: Max: Normal: Solids?, describe: Solid Size: Solid Length: Solids %: Viscosity at Temp: Vapor Pressure at Temp: Specific Gravity: Duty Cycle (hrs/day): Motor Enclosure: Hertz: 5 6 Volts: Phase: 3. Determine the maximum roller speed Duty Cycle (hours/day) of operation See pump performance graphs Viscosity of the fluid < cps: no speed correction needed cps: max. speed 4 rpm, 5 cps: max. speed 3 rpm; use flooded/pressurized suction 5,, cps: max. speed rpm; use flooded/pressurized suction,5, cps: max. speed rpm; use flooded/pressurized suction Note: With viscosities over cps it is very important to oversize the suction line / to times the pump connector size and to keep suction lines as short as possible. Temperature of the fluid: If the fluid temperature pumped is within 5 F (9.4 C) of the maximum temperature rating of the hose, contact factory and select a pump with a maximum speed of rpm. 3. Pump Selection Select pump that can deliver the required flow based on the maximum roller speed and discharge pressure required by the application. Note: It may be required to select a larger pump if solids are larger than the maximum size the pump can handle. 4. Hose Selection Hose selection based on chemical compatibility and temperature. 5. Connector Type and Material Selection 6. Drive Selection Motor eff: Std High Inverter Duty Variable Frequency Drive: Yes No If yes, what environment will controller be mounted: Inside another panel Dry, fairly dust free Dusty area Wet area Wash down area Hazardous area If yes, class and group If Yes, input voltage:

36 MODEL 43 PUMP DATA Performance.75 (.55) Installed Power: hp (kw).5 (.37) 43 6 psig (8 bar) 44 psig (3 bar) 4 (4 ).33 (.5) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gph lph * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 3/8 inch (6 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Wheel: Ductile Iron Frame: Steel Cover: Lexan Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Specifications Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: Lubrication Fluid: Lubricant: Weight (pump only): Weight (with drive): psig (7.6 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. 4 ft.75 max x 3 x 57 mm.66 gal/rev.37 qts (.35 L) max. Glycerine / Glycol lbs. ( kg) 55 lbs. (5 kg) 36

37 Dimensional Drawings See Ordering Information for motor and gearbox sizes. Model 43 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 43 Model 43 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style SS 36 SST 3/4 hose barb PP Polypropylene 3/4 Hose Barb MM PVDF 3/4 Hose Barb 9 Drive Flow Gear Pump Max GPH Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B 7. 74: 8 6 3/4 D : /4 F. 4: /4 H 7.7 9: /4 J : 45 3/4 L D C M N O H H A B E 4 x K Q Q P F I G J A B C D E F G H I J K M N O P Q Inches mm xø ø

38 MODEL 44 PUMP DATA Performance.75 (.55) Installed Power: hp (kw) 44 6 psig (8 bar) 44 psig (3 bar).5 (.37).33 (.5) 4 (4 ) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gph lph Flow: gpm l/min Fluid Characteristics * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Specifications Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 3/4 inch (7 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Wheel: Ductile Iron Frame: Steel Cover: Lexan Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: Lubrication Fluid: Lubricant: Weight (pump only): Weight (with drive): psig (7.6 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. 4 ft.75 max 5 x 37 x 83 mm. gal/rev.4 qts (.4 L) max. Glycerine / Glycol 49 lbs. ( kg) 77 lbs. (49 kg) 38

39 Dimensional Drawings See Ordering Information for motor and gearbox sizes. Model 44 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 44 Model 44 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style SS 36 SST 3/4 hose barb PP Polypropylene 3/4 Hose Barb MM PVDF 3/4 Hose Barb 9 Drive Flow Gear Pump Max GPH Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B : 8 6 3/4 D : /4 F : /4 H 9.5 9: /4 J 4.8 6: / L D C M N O H H A B E 4 x K Q Q P F I G J A B C D E F G H I J K M N O P Q Inches mm xø ø*

40 MODEL 46 PUMP DATA Performance 3. (.) Installed Power: hp (kw) 46 7 psig (5 bar) 45 psig ( bar) 9 psig (7.5 bar) 7 psig (5 bar). (.5) 4 (4 ).5 (.) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gpm l/min m 3 /h * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 6 inch (5 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Shoes: Aluminium Frame: Steel Cover: Electroplated Steel Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Specifications Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: Lubrication Fluid: Lubricant: Weight (pump only): Weight (with drive): 8 psig (5 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. 4 ft 3. max. 5 x 54 x 9 mm.88 gal/rev. qts (. L) max. Glycerine / Glycol lbs. (5 kg) 76 lbs. (8 kg) 4

41 Dimensional Drawings See Ordering Information for motor and gearbox sizes. Model 46 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 46 Model 46 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style BB 36 SST insert w/ 36 SST 5 Lb ANSI flange PP Polypropylene insert w/ 36 SST 5 Lb ANSI flange MM PVDF insert w/ 36 SST 5 Lb ANSI flange 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B.6 96: D.8 54: 3 7 F : H 5.5 8: 63 3 J 7.6 : K 8.8 7: D C L M N O E H H A B 4 x K Q Q P F I G J A B C D E F G H I J K M N O P Q Inches lb mm xø ANSI

42 MODEL 47 PUMP DATA Performance Installed Power: hp (kw) 3. (.) 47 7 psig (5 bar) 45 psig ( bar) 7 psig (5 bar) 9 psig (7.5 bar). (.5) 4 (4 ).5 (.) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gpm l/min m 3 /h * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 77/8 inch (3 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Shoes: Aluminium Frame: Steel Cover: Electroplated Steel Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Specifications Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: 8 psig (5 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. 4 ft 3. max. 3 x 63 x 3 mm.65 gal/rev Lubrication Fluid:.64 qts (.5 L) Lubricant: Weight (pump only): Weight (with drive): * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Glycerine / Glycol 94 lbs. (88 kg) 87 lbs. (3 kg) 4

43 Dimensional Drawings See Ordering Information for motor and gearbox sizes. Model 47 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 47 Model 47 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style BB 36 SST insert w/ 36 SST / 5 Lb ANSI flange PP Polypropylene insert w/ 36 SST / 5 Lb ANSI flange MM PVDF insert w/ 36 SST / 5 Lb ANSI flange 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B 3. 93: D : 3 7 F : H.4 8: J 4.3 : K 6.5 7: D C L M N O E H H A B 4 x K Q Q P F I G J A B C D E F G H I J K M N O P Q Inches lb mm xø ANSI

44 MODEL 49 PUMP DATA Performance (7.5) Installed Power: hp (kw) 49 7 psig (5 bar) 45 psig ( bar) 9 psig (7.5 bar) 7 psig (5 bar) 3. (.) 4 (4 ) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gpm l/min m 3 /h * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Fluid Characteristics Specifications Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 7/8 inch (3 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Shoes: Aluminium Frame: Steel Cover: Steel Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: 8 psig (5 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. 4 ft 5. max. 4 x 67 x 5 mm.35 gal/rev Lubrication Fluid: 5.8 qts (5 L) Lubricant: Weight (pump only): Weight (with drive): * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Glycerine / Glycol. 3 lbs. (9 kg) 463 lbs. ( kg) 44

45 Dimensional Drawings See Ordering Information for motor and gearbox sizes. Model 49 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 49 Model 49 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style BB 36 SST insert w/ 36 SST / 5 Lb ANSI flange PP Polypropylene insert w/ 36 SST / 5 Lb ANSI flange MM PVDF insert w/ 36 SST / 5 Lb ANSI flange 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B 8.4 7: D.6 49: F : H 9. 3: J 4.7 5: K : D Q Q C O M N L E H H A B 4xK F G P I J A B C D E F G H I J K M N O P Q Inches lb mm xø ANSI

46 MODEL 4 PUMP DATA Performance..(7.5) Installed Power: hp (kw) 4 7 psig (5 bar) 45 psig ( bar) 9 psig (7.5 bar) 7 psig (5 bar) 7.5 (5.5) 4 (4 ) 5.5 (4.) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gpm l/min m 3 /h Fluid Characteristics * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Specifications Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 95/8 inch (5 mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Shoes: Cast Iron Frame: Steel Cover: Steel Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: 8 psig (5 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. 4 ft max. 5 x 8 x 8 mm.77 gal/rev Lubrication Fluid:.57 qts ( L) Lubricant: Weight (pump only): Weight (with drive): * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Glycerine / Glycol 43 lbs. (95 kg) 694 lbs. (35 kg) 46

47 Dimensional Drawings See Ordering Information for motor and gearbox sizes. D C Q Q Model 4 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number Order Order Digit Code Description 4 Pump Designation 4 Model 4 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style BB 36 SST insert w/ 36 SST 5 Lb ANSI flange PP Polypropylene insert w/ 36 SST 5 Lb ANSI flange MM PVDF insert w/ 36 SST 5 Lb ANSI flange 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B 6.9 7: 7 5 D 6.9 5: 35 7 F : 48 6 H : 6 8 J : 76 7 O M N L 9 H E H A B 4xK F G P I J A B C D E F G H I J K M N O P Q Inches b 6.4. mm xø ANSI

48 MODEL 44 PUMP DATA Performance 5. (8.5) Installed Power: hp (kw).5 (5.) 44 7 psig (5 bar) 45 psig ( bar) 9 psig (7.5 bar) 7 psig (5 bar) 4 (4 ) 4.75 (.) (5 ) 4 (6 ) 58 (7 ) Temperature: F (C) 76 (8 ) Continuous 4/4h Intermittent* Occasional** Pump Speed: rpm Flow: gpm l/min m 3 /h * Intermittent use: Minimum of hour stop after hours use ** Occasional use: Maximum hour per day Fluid Characteristics Viscosity:, cps max. Liquid Temperature: 8 F (8 C) max. Solid Size: (see page 4) Fiber Length: 395/8 inch ( mm) max. Materials of Construction Casing: Ductile Iron Rotor: Ductile Iron Shoes: Cast Iron Frame: Steel Cover: Steel Casing Oring Seal: Nitrile Hose Materials: NR/NBR/EPDM/Hypalon Specifications Discharge Pressure: Suction Lift (sea level): Suction Pressure: NPSHr: Horsepower:* Hose Size: Displacement: 8 psig (5 bar) max. 9.5 ft (9 m) max..8 psig (.5 bar) max. 4 ft 5 max. 8 x 3 x 9 mm 3.83 gal/rev Lubrication Fluid: 4.7 qts (4 L) Lubricant: Weight (pump only): Weight (with drive): * Pumps are shaft driven and require a gearbox and motor. See Ordering Information on following page for details. Glycerine / Glycol,33 lbs. (6 kg),5 lbs. (93 kg) 48

49 Dimensional Drawings See Ordering Information for motor and gearbox sizes. D C Q Q Model 44 Ordering Information A complete Vector pump order number uses a character order code to identify the desired hose, fittings and drive. Select the appropriate items from the chart below and use the order code from each group to complete the pump assembly order number. 4 3 Order Order Digit Code Description 4 Pump Designation 44 Model 44 Shaft Drive Pump 56 Hose Material (fiberbraided) MF Natural Rubber BF NBR, Oilrated EF EPDM HF Hypalon 78 Connector Material/Style BB 36 SST insert w/ 36 SST 3 5 Lb ANSI flange PP Polypropylene insert w/ 36 SST 3 5 Lb ANSI flange MM PVDF insert w/ 36 SST 3 5 Lb ANSI flange 9 Drive Flow Gear Pump Max GPM Ratio RPM Psig BHP 3Ø, TEFC, 3/46 VAC, 6 Hz 4: Inverter Duty Turndown B 48. : D : 7 F : H 7. 46: J : O M N L E H H A B 4xK F G P I J A B C D E F G H I J K M N O P Q Inches lb mm xø ANSI

50 Accessories Controllers Controllers regulate the motor speed and strokes per minute, providing a flow that is proportional to the motor speed. Selection Process. Ensure that the phase and enclosure match your application.. Using the appropriate chart below, select the controller hp based on the hp of your motor. 3. Match the output voltage to the output voltage of your motor. 4. Match the input voltage to your electrical source. Phase HP Type Input Voltage/Phase Output Voltage/Phase Enclosure Part Number Weight (lbs.) / Sensorless Vector 3 volt/phase 3 volt/3phase NEMA C5NP3P3. Micro AC Inverter 5 volt / phase 3 volt / 3phase IP CIPP3P5. Micro AC Inverter 5 volt / phase 3 volt / 3phase NEMA 4 CN4P3P5 8. Sensorless Vector 3 volt / phase 3 volt / 3phase NEMA CNP3P3. Micro AC Inverter 3 volt / phase 3 volt / 3phase NEMA 4 CN4P3P3 8. Sensorless Vector 3 volt / phase 3 volt / 3phase NEMA CNP3P Sensorless Vector 3 volt / phase 3 volt / 3phase NEMA C3NP3P

51 Controllers 3 Phase HP Type Input Voltage/Phase Output Voltage/Phase Enclosure Part Number Weight (lbs.) / Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA C5N3P3P3. Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA CN3P3P3. Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA CN3P3P3 4.4 Micro AC Inverter 3 volt / 3phase 3 volt / 3phase NEMA 4 CN43P3P Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA C3N3P3P Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA C5N3P3P3 5. 7/ Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA C75N3P3P3 3. Sensorless Vector 3 volt / 3phase 3 volt / 3phase NEMA CN3P3P3 3. Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA CN3P3P46. Micro AC Inverter 46 volt / 3phase 46 volt / 3phase NEMA 4 CN43P3P46 3. Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA CN3P3P46. Micro AC Inverter 46 volt / 3phase 46 volt / 3phase NEMA 4 CN43P3P Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA C3N3P3P Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA C5N3P3P / Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA C75N3P3P46 4. Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA CN3P3P Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA C5N3P3P46 4. Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA CN3P3P Sensorless Vector 46 volt / 3phase 46 volt / 3phase NEMA C3N3P3P

52 Pulsation Dampeners The HP line of pulsation dampeners will reduce vibrations and water hammer in system piping. Dampener Model Pump Models Connection Sizes HP 4, 43, 44, 45 3/4 Hose Barb, 36 SST HP4 5, 35, 6, 46, 49 or.5 5 lb ANSI Flange, 36 SST HP5 7, 44, 4 or.5 5 lb ANSI Flange, 36 SST HP 8, 9, 43, 44, 45 3 or 4 5 lb ANSI Flange, 36 SST HP5, lb ANSI Flange, 36 SST Inside hose bladder materials available: Natural Rubber EPDM Oilrated Nitrile Hypalon 5

53 Hose Rupture Detector A hose rupture detector is designed to provide early indication of hose failure. A leak detector pressure switch can be installed to measure pressure inside the pump casing. If pressure increases inside the pump casing, a signal can be used to disable the pump and notify personnel. Contact the factory to discuss your specific application. 53

54 Other Wanner Engineering Pumps Nine sealless pump models with maximum flow rates from. gpm to 68.5 gpm and discharge pressures from psi to 5 psi depending on pump model. Three highhorsepower pump models with maximum flow rates from 6 gpm to 96 gpm and discharge pressures from 5 psi to 5 psi depending on pump model. Two quintuplex pump models with maximum flow rates from 67 gpm to 57 gpm and discharge pressures from 5 psi to 35 depending on pump model. Six metering pump models with maximum flow rates from 6.5 gph to gph and discharge pressures from psi to 5 psi depending on pump model. Nonmetallic, solid PVDF ANSI centrifugal pumps with total dynamic head to 35 feet and flow capacities to 7 gpm. 54

55 Vector pumps process difficult fluids in many industries including ceramics, building and construction, and electrical products. 55