GENERAL INFORMATION RADIAL TIRE BIAS TIRE O-RING, FLAP, RIM, VALVE, CONVERSION TABLES

Transcription

1

2 GENERAL INFORMATION RADIAL TIRE BIAS TIRE ORING, FLAP, RIM, VALVE, CONVERSION TABLES 2011 OffTheRoad Tire Department, Bridgestone Corporation, Tokyo, Japan All rights reserved. No part of this manual may be reproduced in any form by any electronic or mechanical means, including information storage and retrieval devices or systems, without prior written permission from OffTheRoad Tire Department, Bridgestone Corporation, Tokyo, Japan. Notice: Although great care has been taken in producing this manual, we can accept no responsibility for any loss or damage resulting from undetected errors or misprints which may have occurred. Due to the constant advance of tire technology, the contents of this data book are subject to change without notice. I

3 CONTENTS INTRODUCTION 1. Industry Standard Vehicle Matching Chart... 1 GENERAL INFORMATION 1. Structural Diagram Definitions Classification Tire Markings... 6 RADIAL TIRE 1. Tread Designs Technical Data INTRODUCTION 1. Industry Standard Bridgestone Corporation has developed a wide range of tire patterns and specifications, so that the proper OfftheRoad tire can be matched to any vehicle, service, or operating conditions. Bridgestone s OfftheRoad tires are designed and produced to meet the coonly accepted international standards, those set by the TRA (Tire and Rim Association) in the U.S.A., by the ETRTO (European Tire and Rim Technical Organization) in Europe and/or by the JATMA (Japan Automobile Tire Manufacturers Association) in Japan*. Load capacities, inflation pressures, dimensions such as overall tire diameter and width, as well as the relative rims and tube valves follow these standards. If a tire is to be used for a purpose other than that for which it is originally intended, please consult Bridgestone Corporation for advice. *Where differences exist between the TRA, ETRTO and JATMA standards, Bridgestone selects the most applicable. 2. Vehicle Matching Chart 4. Remarks BIAS TIRE 1. Tread Designs Technical Data Remarks OTHER SPECIFICATION 1. ORing Specifications Flap Specifications Rim and Valve OTHER INFORMATION 1. Unit Conversion Tables Specific Weight (Approximately) APPLICATION Earthmover Grader Loader & Dozer Mobile Crane (HighSpeed) Industrial Logging Compactor Sand VEHICLE Dump Trucks, Motor Scrapers, Articulated Dump Trucks, Coal Haulers, Logging Trucks, Other Mining Trucks, etc. Motor Graders FrontEnd Loaders, Backhoe Loaders, Skid Steer Loaders, Dozers, Shuttle Trucks, LoadHaulDumps, etc. AllTerrain Cranes, HighSpeed Vehicles,etc. Straddle Carriers, Aircraft Towing Tractors, Container Stackers, Counterbalanced Lift Trucks, Mobile Crushers, Log Stackers, etc. LogSkidders Compactor, Road Rollers Sand Trucks II INTRODUCTION 1

4 GENERAL INFORMATION 1. Structural Diagram 2. Definitions 2.1 Tire OffTheRoad Radial Tire (ORR) Belt Casing Ply Chafer Tread The size of each tire is indicated by nominal width and rim diameter in es and. Radial structure is indicated by the letter R. For some tire the aspect ratio is indicated by percentage. Example Radial Tire ; 40.00R57, 33.25R35, 445/95R25 Bias Tire ; , 45/ Star, Ply and Load Index The load capacity of a tire is indicated by the star rating (in case of radial tire) and the ply rating (in case of bias tire). The load index is applied in countries where the ETRTO standards are used. 2.3 Overall Diameter (OD) Overall Diameter is twice the section height of a new tire, plus the nominal rim diameter, including 24hour inflation growth. 2.4 Overall Width (OW) Overall Width is the width of a new tire, including 24 hour inflation growth, and including protective side ribs, bars or decorations. 2.5 Section Width (SW) Section Width is the width of a new tire, including 24 hour inflation growth and including normal sidewalls, but not including protective side ribs, bars, or decorations. 2.6 Static Loaded Radius and Width (SLR, SLW) Static Loaded Radius is the shortest distance from the axle center to the contact surface of a tire and Static Loaded Width is the overall width of a tire, mounted on the approved rim at the specified inflation pressure and placed still and vertically on a flat board, and loaded with the specified load. 2.7 Original Tread Depth (OTD) Original Tread Depth is the tread depth of a new tire measured at the point of treadindicator where available or onefourth the width of the tire crown section from the crown center, including 24hour inflation growth. OffTheRoad Bias Tire (ORS) Inner Liner Overall Width (OW) Section Width (SW) Tread Width Breaker Bead Wire Free Radius Section Height (SH) Rim Width Rim Flange Height Carcass Chafer Overall Diameter (OD) Static Loaded Radius (SLR) Dual Spacing Nominal Rim Diameter Static Loaded Width (SLW) 2 GENERAL INFORMATION 3

5 3. Classification 3.1 Uses and Characteristics of OffTheRoad Tires The characteristics that OffTheRoad tires must possess differ according to their function and the type of vehicles they are mounted on. Type/ Function Vehicles Main tire characteristics required Earthmover Transporting Articulated dump trucks Coal haulers Scrapers Off road trucks Loaders, Bulldozers Tirerollers LHDs Heatresistance, Cutresistance, Wearresistance, Shock burstresistance Traction, Grader Grading, Leveling Maneuverability, Graders (directional stability) Loader and dozer Loading and dozing Cutresistance, Wearresistance Stability Oilresistance, Compactor Compacting Cutresistance, Wearresistance Logging Logskidding Rigid dump trucks Traction, Flotation, Cutresistance 3.2 TRA Classification and Corresponding Bridgestone OffTheRoad Tires OffTheRoad tires are classified by the TRA as follows, and the names of the tread patterns of the corresponding Bridgestone OffTheRoad tires are described below. TRA Classification Tread Type Bridgestone Tread Radial Bias E= Earthmover (Haulage ) E2 Traction VUT VKT VSB VFT VHS VSW E3 Rock VLT VMT VTS WL RL VL2 VEL VRL VRF E4 Rock Deep L317 VLTS VSNT VMTS RLS ELS2 VMTP VZTS VZTP VELSL VELS VRLS VREP VRDP VRPS VRQP E7 Flotation VSJ SCP2 G=Grader G1 Rib RG G2 Traction VUT VKT VSW GL FG G3 Rock RL G4 Rock Deep VMTS L=Loader & Dozer (Slow Speed ) L2 Traction Regular VUT VKT VSW GL FG L3 Rock Regular VLT VMT VJT VTS RL VL2 L4 Rock Deep VLTS VSNT VSNL RLS NL L5 Rock ExtraDeep VSDT VSDL DL L5S Smooth ExtraDeep VSMS STMS C=Compactor C1 Smooth RR C2 Grooved AL2 LS=Logging LS2 Intermediate TGS Mobile Crane Mobile Crane (HighSpeed) VGT VSB VHB VHS VSW Industrial Industrial VHB VEL VCH VCHD VCHS VELS VRLS VSDL VSMS RL RLS ELS2 STMS YS2 Mobile crane (Highspeed) Highspeed Travelling Logskidders AllTerrain Cranes Heatresistance, Wearresistance, Traction Design TreadDepth 100% 150% 250% Uneven wear, Industrial Handling & Towing Wearresistance, Stability Handling & Towing Equipments Regular Tread Deep Tread Extra Deep Tread E2/E3 E4 L2/L3 L4 L5/L5S G2/G3 G4 4 GENERAL INFORMATION 5

6 4. Tire Markings (ORR) 1 1 Brand Name 4.2 Type of Tire Structures Classified by and Designated by Bridgestone Each Bridgestone tire has a Bridgestone code number on the tire sidewall according to its specifications. 2 Bridgestone s Specifications Code 3 Name 4 Serial Number O F F T H E R OA D E A R T H M OV I N G T Y P E 2 A C U T R E S I S TA N T For Earthmover service O F F T H E R OA D L OA D E R & D O Z E R T Y P E 2 A C U T R E S I S TA N T For Loader and Dozer service O F F T H E R OA D G R A D E R T Y P E 2 A C U T R E S I S TA N T For Grader service Tire, Star,Tubeless or Tube Type O F F T H E R OA D INDUSTRIAL SERVICE For Industrial service O F F T H E R OA D A N D WHEEL CRANE USE For Mobile Crane Type of Tire Designation Regular R 49 Star Rim Diameter (es) Radial Structure Section Width (es) Wide Base R 35 Star Rim Diameter (es) Radial Structure Section Width (es) Super Wide Base 40 / PR Ply Rim Diameter (es) Aspect Ratio 65 Series Section Width (es) 170 E 385 / 95 R 24 Rim Diameter (es) Radial Structure Aspect Ratio 95 Series Section Width () Speed Symbol Load Index Tire Aspect Ratio SH SW = 0.95 SH = 0.80 SW SH = 0.65 SW SH, SW : See Page 3 Tire Structures Classified by Type of and Bridgestone s Designations BS Code No. Structure 1A Standard Earthmover (E) 2A Cutresistant 3A Heatresistant Grader (G) 1A Standard 2A Cutresistant 2A Cutresistant Loader & Dozer (D) 2V Special cutresistant (Type V ) 2Z Special cutresistant (Type Z ) Logging (S) 2V Standard NOTES: Bias Tire Only 2V tires are standard for log skidder service since the possibility of the cutting is high in log skidder operations. Structure: Characteristics: Type of : A: Standard V: Cutresistant type V (Steel Breaker) Z: Cutresistant type Z (Side Steel Breaker) 1: Standard 2: Cutresistant 3: Heatresistant E: Earthmover G: Grader D: Loader & Dozer S: Logging Type V Steel breaker construction Steel Breaker Tire Type Z Side steel breaker construction Steel Breaker Bias Tire Steel Breaker OfftheRoad tires feature breaker material which is changed from nylon to steel in order to resist cutting and cut bursting. Bridgestone Steel Breaker OfftheRoad tires are widely used on loaders at mining and quarry sites, loaders and shuttle trucks in underground mines, and also on log loaders. Side Steel Breaker Bias Tire In this tire the steel breaker extends to the sidewall of the tire to protect it against damage. The construction is similar to that described above. 6 GENERAL INFORMATION 7

7 4.3 Load Index The LOAD INDEX is an international numerical code for the maximum load a tire can carry at the speed indicated by its speed symbol under service conditions specified by Bridgestone. 4.4 Speed Symbol The SPEED SYMBOL indicates the speed at which the tire can carry a load corresponding to its load index under service conditions specified by Bridgestone. LI kg LI kg LI kg LI kg LI kg LI kg Speed Symbol Speed (km/h) A A A A A A A A Speed Symbol Speed (km/h) B 50 C 60 D 65 E 70 F 80 G Conversion Table: Star to Ply Earthmover Tire Star Corresponding Ply 12.00R24 up to R24 up to R25 up to R25 up to R25 up to 24 up to R33 up to R35 up to R57 up to R25 up to R25 up to 24 up to 28 25/65R25 up to R25 up to 24 up to R25 up to R25 up to R29 up to R29 up to R35 up to R35 up to R39 up to /75R39 up to 54 Grader Loader Tire Star Corresponding Ply 14.00R24 up to R24 up to R25 up to R25 up to R25 up to R25 up to 24 up to R25 up to 24 up to R25 up to 24 up to R25 up to 28 up to R29 up to 34 35/65R33 up to 36 45/65R45 up to 50 Note: Due to the practice of altering inflation pressure to improve flotation on sand, Bridgestone does not apply a star rating to tire size 21.00R25 VSJ. 8 GENERAL INFORMATION 9

8 4.6 Conversion Table Metric Inch RADIAL TIRE 1. Tread Designs Earthmover E2 385/95R24, R24, /95R24, R24, /80R R25 505/95R R25 525/80R R25 750/65R25 30/65R Dual Specification Codes Some Bridgestone OffTheRoad Tires have dual specification codes which can be used for both services. Combination Loader & Dozer + Earthmover Construction Radial Bias Designation 26.5R25 MS* VLT T DE VL2 T DE2 *1 D2A *2 E2A D2A E2A VSTEEL VSTEEL VSTEEL ULTRA TRACTION KTRACTION SBLOCK (VUT) (VKT) (VSB) E2 Loader & Dozer + Grader Bias FG T DG2 D2A G2A Earthmover + Grader Radial 17.5R25 1 VKT T EG2 E2A G2A Multiple Star Bridgestone Radial Tires marked with LOADER & DOZER (one star) and EARTHMOVER (two star) have specified load capacity on each servicing condition. Strength of tire casing is designed to constrain inflation pressure used. <26.5R25 as an example> Type of Loader Earthmover Star (one star) (two stars) Inflation Pressure 5.00 bar 5.25 bar Load (Load Index) 15,000 kgs (202) 11,500 kgs (190) Speed (Speed Symbol) 10 km/hour (A2) 50 km/hour (B) VSTEEL VSTEEL VSTEEL FTRACTION HSERVICE SNOW WEDGE (VFT) (VHS) (VSW) E3 Description on Tire Sidewall VSTEEL Wide Base Regular VSTEEL LTRACTION VSTEEL MTRACTION TRACTIONSTABILITY (VLT) (VMT) (VTS) 10 RADIAL TIRE 11

9 E3 E4 VSTEEL Wide Base Regular VSTEEL ELUG VSTEEL RLUG ROCK FAST (VEL) (VRL) (VRF) E R24~ 21.00R33~ VSTEEL VSTEEL 16.00R R57 ROCK EPREMIUM ROCK DEEP VSTEEL RLUG S (VRLS) (VREP) PREMIUM (VRDP) E4 Sand E7 L317 VSTEEL VSTEEL VSTEEL VSTEEL LTRACTION S NTRACTION MTRACTION S MTRACTION (VLTS) (VSNT) (VMTS) PREMIUM (VMTP) VSTEEL VSTEEL VSTEEL ROCK PREMIUM ROCK QUARRY JAMAL SERVICE (VRPS) PREMIUM (VRQP) (VSJ) Grader E4 G2 G4 VSTEEL VSTEEL 37.00R R25~ 40.00R57 31/90R49 ZTRACTION S ZTRACTION 40.00R R35 50/90R57 46/90R57 (VZTS) PREMIUM (VZTP) VELSL VSTEEL ELUG S (VELS) VSTEEL VSTEEL VSTEEL VSTEEL UTRACTION KTRACTION SNOW WEDGE MTRACTION S (VUT) (VKT) (VSW) (VMTS) 12 RADIAL TIRE 13

10 Loader & Dozer L2 L3 Mobile Crane (HighSpeed) VSTEEL VSTEEL VSTEEL VSTEEL VSTEEL UTRACTION KTRACTION SNOW WEDGE LTRACTION MTRACTION (VUT) (VKT) (VSW) (VLT) (VMT) L3 L4 VSTEEL VSTEEL VSTEEL VSTEEL VSTEEL GTRACTION SBLOCK HBLOCK HIGHWAY SERVICE SNOW WEDGE (VGT) (VSB) (VHB) (VHS) (VSW) Industrial VSTEEL VSTEEL TRACTION VSTEEL VSTEEL VSTEEL JTRACTION STABILITY LTRACTION S NTRACTION NLUG (VJT) (VTS) (VLTS) (VSNT) (VSNL) VSTEEL VSTEEL VSTEEL VSTEEL VSTEEL CONTAINER HBLOCK ELUG CONTAINER CONTAINER HANDLER STABILITY (VHB) (VEL) HANDLER HANDLER DEEP AND SAFETY (VCH) (VCHD) (VCHS) L5 L5S VSTEEL VSTEEL VSTEEL SMOOTH SUPERDEEP DLUG TREADMS TRACTION (VSDT) (VSDL) (VSMS) VSTEEL VSTEEL VSTEEL VSTEEL ELUG S RLUG S DLUG SMOOTH TREADMS (VELS) (VRLS) (VSDL) (VSMS) 14 RADIAL TIRE 15

11 2. Earthmover HEAT RESISTANT CUT RESISTANT VLT VSB VFT VKT VMT VSW L317 VMTS VMTP VLTS VSNT VZTS VZTP TRACTION VHS VRL VEL VELSL ROCK VRF VREP VELS/VRLS VRDP VRPS VRQP VUT(E2) VKT(E2) VSB(E2) VFT(E2) Type Star Type Star Type Star Type Star Type Star Type Star 335/80 R 20 T/L 365/80 R 20 T/L 405/70 R 20 T/L R 24 T/T R 25 T/L R 25 T/L 2 25/65 R 25 T/L R 25 T/L R 29 T/L R 39 T/L R 24 T/T R 25 T/L R 33 T/L R 49 T/L R 49 T/L 2 T/T: Tube Type T/L: Tubeless Type MS: Multiple Star VHS(E2) VSW(E2) VLT(E3) VSW is especially designed for snow surface operations R 51 T/L R 25 T/L MS 23.5 R 25 T/L MS 20.5 R 25 T/L MS 23.5 R 25 T/L MS 750/65(30/65) R 25 T/L MS 26.5 R 25 T/L MS 29.5 R 25 T/L MS R 29 T/L R 35 T/L /75 R 39 T/L 2 VTS(E3) VMT(E3) 875/65 R 29 T/L MS 17.5 R 25 T/L R 25 T/L R 25 T/L R 51 T/L R 51 T/L R 57 T/L 2 VEL(E3) VRL(E3) VRF(E3) L317(E4) R 25 T/L R 33 T/L R 35 T/L R 35 T/L R 35 T/L R 35 T/L R 35 T/L /75 R 39 T/L R 49 T/L 2 VLTS(E4) 53/80 R 63 T/L 2 59/80 R 63 T/L R 20 T/T R 20 T/T 3 12 R 22.5 T/L R 24 T/T R 25 T/L MS 23.5 R 25 T/L MS 750/65(30/65) R 25 T/L R 25 T/L R 25 T/L 2 NEW 875/65 R 29 T/L MS T/T: Tube Type T/L: Tubeless Type MS: Multiple Star 16 RADIAL TIRE 17 VSNT(E4) VMTS(E4) VMTP(E4) VZTS(E4) 26.5 R 25 T/L MS 29.5 R 25 T/L MS 29.5 R 29 T/L MS 35/65 R 33 T/L MS R 24 T/T R 25 T/L R 25 T/L R 25 T/L R 33 T/L R 35 T/L R 49 T/L R 24 T/T R 33 T/L R 33 T/L R 35 T/L R 35 T/L R 49 T/L R 49 T/L R 51 T/L R 57 T/L R 57 T/L 2 VZTP(E4) VELSL(E4) VELS(E4) VRLS(E4) 46/90 R 57 T/L R 57 T/L R 57 T/L R 25 T/L R 33 T/L R 35 T/L 2 31/90 R 49 T/L R 57 T/L 2 46/90 R 57 T/L 2 50/90 R 57 T/L R 24 T/T R 25 T/L R 25 T/L R 33 T/L 2 T/T R 35 T/L R 49 T/L R 49 T/L R 51 T/L R 51 T/L R 51 T/L R 57 T/L 2 VREP(E4) NEW VRDP(E4) VRPS(E4) NEW VRQP(E4) R 49 T/L R 49 T/L R 51 T/L 2 42/90 R 57 T/L R 57 T/L 2 46/90 R 57 T/L 2 53/80 R 63 T/L R 51 T/L R 57 T/L 2 46/90 R 57 T/L 2 50/90 R 57 T/L 2 53/80 R 63 T/L 2 59/80 R 63 T/L R 33 T/L R 35 T/L 2

12 Grader Loader & Dozer HEAT RESISTANT CUT RESISTANT HEAT RESISTANT CUT RESISTANT VUT VSW VKT TRACTION VUT VLT TRACTION VMTS ROCK VSW VKT VJT VMT VTS VLTS VSNT VSDT ROCK VSNL VSDL VSMS Type Star Type Star Type Star Type Star VUT(G2) VKT(G2) VSW(G2) VMTS(G4) R 24 TG T/L R 24 TG T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 24 TG T/L R 24 TG T/L R 25 T/L R 24 TG T/L R 24 TG T/L R 25 T/L R 24 TG T/L 1 VSW is especially designed for snow surface operations. T/T: Tube Type T/L: Tubeless Type TG: For SemiDrop Center Rim T/T: Tube Type T/L: Tubeless Type MS: Multiple Star TG: For SemiDrop Center Rim VSW is especially designed for snow surface operations. 18 RADIAL TIRE 19 VUT(L2) VKT(L2) VSW(L2) NEW VLT(L3) 335/80 R 20 T/L 365/80 R 20 T/L 405/70 R 20 T/L 15.5 R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 24 TG T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 24 TG T/L R 25 T/L R 25 T/L MS 23.5 R 25 T/L MS 600/65 R 25 T/L R 25 T/L MS 23.5 R 25 T/L MS 750/65(30/65) R 25 T/L MS 26.5 R 25 T/L MS 29.5 R 25 T/L MS VMT(L3) 17.5 R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L 1 VJT(L3) NEW 17.5 R 25 T/L R 25 T/L R 25 T/L R 25 T/L 1 NEW 29.5 R 25 T/L 1 VTS(L3) VLTS(L4) NEW VSNT(L4) VSNL(L4) 550/65 R 25 T/L 1 650/65 R 25 T/L 1 750/65 R 25 T/L 1 775/65 R 29 T/L 1 875/65 R 29 T/L R 25 T/L MS 23.5 R 25 T/L MS 875/65 R 29 T/L MS 26.5 R 25 T/L MS R 25 T/L MS R 29 T/L MS 2 35/65 R 33 T/L MS R 20 T/T 2 35/65 R 33 T/L 2 45/65 R 45 T/L 2 VSDT(L5) VSDL(L5) 23.5 R 25 T/L R 25 T/L R 25 T/L R 29 T/L /65 R 33 T/L R 15 T/T R 15 T/T R 15 T/L R 20 T/T R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 25 T/L R 29 T/L /65 R 33 T/L /65 R 39 T/L 1 45/65 R 45 T/L /65 R 51 T/L /80 R 57 T/L 60/80 R 57 T/L VSMS(L5S) 9.00 R 20 T/T R 20 T/T R 24 T/T R 24 T/T R 25 T/L R 25 T/L R 25 T/L R 29 T/L 2 NEW

13 Mobile Crane (HighSpeed) Industrial ON ROAD OFF ROAD VHB VCHS VSB VGT TRACTION VEL VEL R 24 T/T R 25 T/L R 25 T/L 3 NEW R 20 T/T R 24 T/T R 24 T/T R 24 TG T/L R 25 T/L R 33 T/L R 25 T/L 3 VHB VELS VSW VHS R 33 T/L 3 Type Type Type VGT VHB VSW 24 R 21 T/L 170E 385/95 R E 385/95 R 25 T/T T/L 170E 445/80 R 25 (14.00R24) (14.00R25) T/L (17.5R25) 177E 445/95 R E 445/95 R 25 T/L T/L (16.00R25) (16.00R25) VSB 186E 505/95 R E 385/95 R 24 T/L T/T (18.00R25) (14.00R24) 170E 385/95 R 25 VHS T/L (14.00R25) 170E 385/95 R 24 T/T (14.00R24) 170E 385/95 R 25 (14.00R25) T/L 170F 385/95 R 25 (14.00R25) T/L 177E 445/95 R 25 (16.00R25) T/L 174F 445/95 R 25 (16.00R25) T/L 186E 505/95 R 25 (18.00R25) T/L 179E 525/80 R 25 (20.5R25) T/L VCH VCHD R 20 T/T R 24 T/T R 24 T/T R 25 T/L 2 Sand VRLS VSDL VSMS R 25 T/L R 25 T/L 2 35/65 R 33 T/L R 25 T/L 2 VSW is especially designed for snow surface operations. T/T: Tube Type T/L: Tubeless Type VSJ(E7) R 20 T/T R 25 T/L T/T: Tube Type T/L: Tubeless Type TG: For SemiDrop Center Rim 20 RADIAL TIRE 21

14 3. Technical Data Tire LI/SS Star TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 15" 8.25R15 VSDL 2 L5 D2A T R15 VSDL 2 L5 D2A V R15 VSDL 2 L5 D2A /1.5 Tubeless " 9.00R20 VSMS 2 L5S D2A T R20 L317 3 E V R20 L317 3 E V VSDL 2 L5 D2A VSMS 2 L5S D2A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 15" kpa psi VSDL Loader 2 10 kg lbs VSDL 2 kg lbs VSDL 2 kg lbs " VSMS Loader 2 10 kg lbs L317 E/M E kg lbs L317 E4 3 kg lbs VSDL Loader 2 VSMS 10 kg lbs R R R R R R20 VCH 3 Industrial IDU See characteristics page 46 VCHS 176A5 3 Industrial IDU 14.00R20 VSNL 2 L4 D2A WI R20 VSJ 28 E7 See characteristics page /80R20 VUT 136B E2 DE x20 Tubeless 147A2 L /80R20 VUT 141B E2 DE x20 Tubeless 153A2 L /70R20 VUT 143B E2 DE x20 Tubeless 155A2 L " 24R21 VGT Mobile Crane Tubeless See characteristics page " 12R22.5 L317 3 E Tubeless For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 22 RADIAL TIRE 23 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. VCH VCHS IDU See characteristics page 47 VSNL Loader 2 10 kg lbs VSJ Sand See characteristics page 51 kpa psi VUT Loader L2 10 kg lbs VUT L2 kg lbs VUT L2 kg lbs " VGT High Speed See characteristics page " kpa psi L317 E/M 3 50 kg lbs For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page R R20 335/80R20 12R R21 405/70R20 365/80R20

15 Tire LI/SS Star TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 24" 12.00R24 L317 3 E V VMTP 3 E4 E2A VSMS 2 L5S D2A VCH 2 Industrial IDU Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 24" kpa psi L317 E/M 3 VMTP 50 kg lbs VSMS Loader 2 10 kg lbs VCH IDU VCHS 12.00R24 New VCHS Industrial IDU See characteristics page 46 See characteristics page R24 TG VUT 1 G2 G2A TG Tubeless R24 VKT 3 E2 E2A W VSB 3 E2 E2A VHB 3 Industrial See characteristics page 46 VMTS 3 E4 E2A W E1A VRLS 3 E4 E2A VSMS 2 L5S D2A VCH 3 Industrial IDU VCHS 196A5 3 Industrial IDU See characteristics page R24 TG VKT 1 G2 G2A TG Tubeless L2 D2A VUT 1 G2 G2A VSW 3 G VA A8 1 DG TG 175A2 L kpa psi VUT Grader 1 40 kg lbs kpa psi VKT E/M 3 VSB 50 kg VMTS 30 lbs VRLS VSMS Loader 2 10 kg lbs VHB IDU VCH VCHS See characteristics page 47 kpa psi VKT Grader 1 3 VSW=Consult a Bridgestone Representative. VUT 40 kg VSW 25 lbs VKT Loader 1 VSW 10 kg lbs R24 TG 14.00R R24 TG For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 25

16 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 14.00R24 TG VMTS 1 G4 G2A TBA TBA TG Tubeless TBA TBA VCHS 196A5 3 Industrial IDU See characteristics page /95R24 VSB Logging W (14.00R24) 170E Mobile Crane VHB 170E Mobile Crane VHS 170E Mobile Crane See characteristics page R24 TG VKT 1 G2 G2A VA Tubeless VSW 1 G " 14.00R25 VSB 3 E2 E2A /1.5 Tubeless VMTS 3 E4 E2A E3A VRLS 3 E4 E2A /95R25 VSB Logging /1.5 (14.00R25) 170E Mobile Crane Tubeless VHS 170E Mobile Crane 170F VSW 170E Mobile Crane See characteristics page R25 VUT 2 G2, L2 DG /1.3 Tubeless VKT 1 L2 D2A VSDL 1 L5 D2A R25 VMTS 2 E4 E2A /2.0 Tubeless VRLS 2 E4 E2A E1A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VMTS Grader 1 40 kg lbs VCHS IDU See characteristics page 47 kpa psi VSB Logging Load J L Range (18PR) (20PR) kg Maximum Speed = 88km/h (55mph) lbs VSB High VHB Speed See characteristics page 49 VHS kpa psi VKT Grader 1 VSW 40 kg lbs " kpa psi VSB E/M 3 VMTS 50 kg VRLS 30 lbs kpa psi VSB Logging Load J L Range (18PR) (20PR) VSB High kg Maximum Speed = 88km/h (55mph) lbs VHS Speed See characteristics page 49 VSW kpa psi VUT Loader 1 2 VKT 10 kg VSDL 5 lbs kpa psi VUT Grader 1 For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. 40 kg For extreme conditions, consult a Bridgestone Representative for additional 25 lbs recoended operating requirements. kpa psi VMTS E/M 2 VRLS 50 kg lbs R R25 385/95R25 (14.00R25) 14.00R R24 TG 385/95R24 (14.00R24) 14.00R24 TG For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 27

17 Tire LI/SS Star TRA Code or Spec TKPH TMPH 16.00R25 VHB 2 Industrial IDU Tubeless VCHD 2 Industrial IDU VRLS 2 Industrial IDU 445/95R25 VHB 177E Mobile Crane (16.00R25) Tubeless VHS 177E Mobile Crane 174F VSW 177E Mobile Crane Approximate Inflated Dimensions OD OW SLR SLW OTD See characteristics page 46 See characteristics page 48 Minimum Recoended Dual Spacing Rim/Flange Height VHB VCHD VRLS VHB VHS VSW Max.Speed km/h mph IDU High Speed Tire Load Limits at Various Cold Inflation Pressures See characteristics page 47 See characteristics page /95R25 (16.00R25) 16.00R R25 VKT 1 E2 EG /1.5 Tubeless G L2 D2A VUT 1 G2, L2 DG New VSW 153A8 1 G2 DG A2 L VMT 2 E3 E1A L3 D2A VJT 176A2 1 L3 D2A TBA TBA TBA TBA VSDL 2 L5 D2A VSMS 2 L5S D2A /80R25 VGT 170E Mobile Crane (17.5R25) See characteristics page 48 Tubeless 18.00R25 VKT 2 E2 E1A /2.5 Tubeless VEL 2 E3 E2A Industrial See characteristics page 46 VMTS 2 E4 E2A / VELS 2 E4 E2A E1A kpa psi VKT E/M 1 2 VMT 50 kg lbs VUT Loader 1 2 VKT 10 kg VSW 5 lbs VMT VJT VSDL VSMS kpa psi VUT Grader 1 VKT 40 kg VSW 25 lbs VGT High Speed See characteristics page 49 kpa psi VKT E/M 2 VEL 50 kg VMTS 30 lbs VELS VEL IDU See characteristics page 47 For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. For extreme conditions, consult a Bridgestone Representative for additional recoended operating requirements. 17.5R25 445/80R25 (17.5R25) 18.00R25 For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 29

18 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 18.00R25 VSMS 2 L5S D2A /2.5 Tubeless Industrial VHB 3 Industrial IDU VCHS 214A5 3 Industrial IDU 505/95R25 VHB 186E Mobile Crane (18.00R25) Tubeless VHS 186E Mobile Crane See characteristics page 46 See characteristics page R25 VKT 1 L2 D2A AL/1.7( 1only) Tubeless /2.0 VSW MS E2, L2 DE VUT 1 G2, L2 DG VLT 177B MS E3 DE A2 L VMT 1 L3 D2A VJT 186A2 1 L3 D2A VLTS 177B MS E4 DE A2 L VSDL 2 L5 D2A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VSMS Loader kg lbs VSMS IDU VHB VCHS VHB VHS High Speed See characteristics page 47 See characteristics page 49 kpa psi VSW E/M 1 2 VLT 50 kg VLTS 30 lbs kpa psi VUT Grader 1 40 kg lbs For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. For extreme conditions, consult a Bridgestone Representative for additional recoended operating requirements. kpa psi VUT Loader 1 2 VKT 10 kg VSW 5 lbs VLT VMT VJT VLTS VSDL 505/95R25 (18.00R25) 18.00R R25 525/80R25 VHS 179E Mobile Crane (20.5R25) Tubeless 21.00R25 VSJ E7 Tubeless See characteristics page 48 See characteristics page 50 VHS VSJ High Speed See characteristics page 49 Sand See characteristics page /80R25 (20.5R25) 21.00R25 For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 31

19 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 23.5R25 VKT 1 L2 D2A /2.5 Tubeless VSW MS E2, L2 DE VUT 1 G2, L2 DG VLT 185B MS E3 DE A2 L VMT 2 E3 E2A L3 D2A VJT 195A2 1 L3 D2A VLTS 185B MS E4 DE A2 L VSDT 201A2 2 L5 D2A A VSDL 2 L5 D2A Industrial IDU See characteristics page 46 25/65R25 VKT 2 E2 E2A /2.0 Tubeless /65R25 VTS 1 L3 D2A (14.00/1.5) Tubeless /2.0 New 600/65R25 VSW 187A2 1 L3 D2A TBA TBA 31.5 (17.00/1.7, 17.00/2.0) Tubeless TBA TBA 19.50/ /65R25 VTS 1 L3 D2A /2.5 Tubeless /65R25 VLT 190B MS E3 DE (22.00/3.0) (30/65R25) 202A2 L /3.0 Tubeless VTS 1 L3 D2A VLTS 190B 2 E4 E2A R25 VKT 2 L2 D2A /3.0 Tubeless VLT 193B MS E3 DE A2 L VMT 2 L3 D2A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VSW E/M 1 2 VLT 50 kg VMT 30 lbs VLTS kpa psi VUT Grader 1 40 kg lbs For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. For extreme conditions, consult a Bridgestone Representative for additional recoended operating requirements. kpa psi VUT Loader 1 2 VKT 10 kg VSW 5 lbs VLT VMT VJT VLTS VSDT VSDL VSDL IDU See characteristics page 47 VKT E/M 2 50 kg lbs VTS Loader 1 10 kg lbs VSW 1 kg lbs VTS 1 kg lbs VLT E/M 2 VLTS 50 kg lbs VLT Loader 1 VTS 10 kg lbs VLT E/M kg lbs VKT Loader 1 2 VLT 10 kg VMT 5 lbs R25 750/65R25 (30/65R25) 650/65R25 600/65R25 550/65R25 25/65R R25 For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 33

20 TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD Tire LI/SS or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height New 26.5R25 VJT 202A2 1 L3 D2A /3.0 Tubeless VLTS 193B 2 E4 E2A VSNT MS E4 DE L D2A VSDT 209A2 2 L5 D2A A VSDL 2 L5 D2A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VLTS E/M 1 2 VSNT 50 kg lbs VJT Loader 1 2 VSNT 10 kg VSDT 5 lbs VSDL VSMS 26.5R25 VSMS 2 L5S D2A R25 VKT 2 E2 E2A /3.5 Tubeless E1A New VLT 200B MS E3 DE A2 L VMT 2 E3 E2A E1A A2 1 L3 D2A VJT 208A2 1 L3 D2A TBA TBA TBA TBA VLTS 200B 2 E4 E2A VSNT MS E4 DE L D2A VSDT 216A2 2 L5 D2A A VSDL 2 L5 D2A VKT E/M 1 2 VLT 50 kg VMT 30 lbs VLTS VSNT VLT Loader 1 2 VMT 10 kg VJT 5 lbs VSNT VSDT VSDL 29.5R25 29" 775/65R29 VTS 1 L3 D2A (24.00/3.5) Tubeless / /65R29 VTS MS E3 DE /3.5 Tubeless L (28.00/3.5) New VLTS 203B MS E4 DE2 TBA TBA TBA TBA A2 L TBA TBA 29.5R29 VKT 2 E2 E2A /3.5 Tubeless E1A VSNT MS E4 DE L D2A For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by " VTS Loader 1 10 kg lbs VTS E/M 2 VLTS 50 kg lbs VTS Loader 1 VLTS 10 kg lbs VKT E/M 1 2 VSNT 50 kg lbs VSNT Loader kg lbs For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE /65R29 875/65R R29

21 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 29.5R29 VSDT 218A2 2 L5 D2A /3.5 Tubeless 211A VSDL 2 L5 D2A VSMS 2 L5S D2A R29 VLT 2 E3 E2A /3.5 Tubeless " 18.00R33 VFT 2 E /2.5 Tubeless E1A E3A VEL 2 E3 E1A E3A VMTS 2 E4 E2A E1A VMTP 2 E4 E2A E1A VELS 2 E4 E2A E1A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VSDT Loader 1 2 VSDL 10 kg VSMS 5 lbs VLT E/M 2 50 kg lbs " kpa psi VFT E/M 2 VEL 50 kg VMTS 30 lbs VMTP VELS VRQP 33.25R R R33 3 Industrial See characteristics page 46 VCHS VELS IDU VRQP 2 E4 E2ALS / See characteristics page 47 VCHS 219A5 3 Industrial IDU See characteristics page R33 VMTP 2 E4 E2A /3.0 Tubeless E1A R33 VRLS 2 E4 E2A VMTP E/M 2 VRLS 50 kg lbs R33 35/65R33 VSNT MS E4 DE /3.5 Tubeless L D2A VSNL 2 L4 D2A New VSDT 224A2 2 L5 D2A A kpa psi VSNT E/M 2 50 kg lbs VSNT Loader 1 2 VSNL 10 kg VSDT 5 lbs /65R33 For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 37

22 Tire LI/SS Star TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD See characteristics page 46 Minimum Dual Spacing Recoended Rim/Flange Height 35" 35/65R33 VSDL 2 L5 D2A /3.5 Tubeless Industrial IDU 21.00R35 VEL 2 E /3.0 Tubeless E3A VMTP 2 E4 E2A E1A VELS 2 E4 E2A E1A R35 VEL 2 E /3.5 Tubeless E1A VMTS 2 E E3A VMTP 2 E4 E2A E1A VRLS 2 E4 E2A E1A E3A VRQP 2 E4 E2ALS R35 VRL 2 E /3.5 Tubeless E1A R35 VRL 2 E /3.5 Tubeless E1A R35 VLT 2 E3 E2A /4.0 Tubeless E1A VRL 2 E E1A " 37.5R39 VKT 2 E /4.5 Tubeless E1A /75R39 VLT 2 E3 E2A /4.5 Tubeless E1A VRL 2 E E1A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 35" kpa psi VSDL Loader kg lbs VSDL IDU See characteristics page 47 kpa psi VEL E/M 2 VMTP 50 kg VELS 30 lbs VEL E/M 2 VMTS 50 kg VMTP 30 lbs VRLS VRQP kpa psi VRL E/M E kg lbs VRL E2 2 E3 kg lbs VLT E2 2 VRL E3 kg E3 lbs " VKT E/M 2 50 kg lbs VLT E/M 2 VRL 50 kg lbs /75R R R R R R R35 35/65R33 For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page RADIAL TIRE 39

23 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 45/65R39 VSDL 1 L5 D2A /4.5 Tubeless /4.5 45" 45/65R45 VSNL 2 L4 D2A TBA TBA /4.5 Tubeless TBA TBA VSDL 2 L5 D2A " 24.00R49 VFT 2 E /3.5 Tubeless E1A VMTP 2 E4 E2A VRLS 2 E4 E2A E1A E3A R49 VFT 2 E2 E2A /4.0 Tubeless E3A VRL 2 E E1A E3A VMTS 2 E4 E2A E1A E3A VMTP 2 E4 E2A E1A E3A VRLS 2 E4 E2A E1A E3A New VREP 2 E4 E2A E1A E3A VRDP 2 E4 E2A E1A E3A /90R49 VELSF 2 E4 E2A /4.0 Tubeless E1A " 30.00R51 VMT 2 E /4.5 Tubeless E3A VRLS 2 E4 E2A E1A E3A For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VSDL Loader 1 10 kg lbs " VSNL Loader 1 2 VSDL 10 kg lbs " VFT E/M 2 VMTP 50 kg VRLS 30 lbs VFT E/M 2 VRL 50 kg VMTS 30 lbs VMTP VRLS VREP VRDP VELSF E/M 2 50 kg lbs " VMT E/M 2 VRLS 50 kg lbs For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page R51 31/90R R R49 45/65R45 45/65R39 40 RADIAL TIRE 41

24 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 33.00R51 VMT 2 E /5.0 Tubeless E1A E3A VMTP 2 E4 E2A E1A VRLS 2 E4 E2A E1A E3A VRDP 2 E4 E2A E1A E3A New VRPS 2 E4 E2A TBA TBA TBA TBA R51 VHS 2 E /5.0 Tubeless E3A VRLS 2 E4 E2A E1A E3A /65R51 VSDL 2 L5 D2A /4.5 Tubeless " 37.00R57 VZTS 2 E4 E2A /6.0 Tubeless E1A E3A VELSL 2 E E3A VRLS 2 E4 E2A E1A E3A /90R57 VRDP 2 E4 E2A /6.0 Tubeless E1A E3A R57 VMT 2 E3 E2A /6.0 Tubeless E1A E3A VZTS 2 E4 E2A E1A E3A VELSL 2 E E3A VELS 2 E4 E2A E1A E3A VRDP 2 E4 E2A E1A E3A VRPS 2 E4 E2A E1A E3A For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VMT E/M 2 VMTP 50 kg VRLS 30 lbs VRDP VRPS VHS E2 2 VRLS kg lbs VSDL Loader 2 10 kg lbs " VZTS E/M E4 2 VELSL 50 E4 kg VRLS 30 E4 lbs VRDP E4 2 kg lbs VMT E3 2 VZTS E4 kg VELSL E4 lbs VELS E4 VRDP E4 VRPS For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page R57 42/90R R57 50/65R R R51 42 RADIAL TIRE 43

25 Tire LI/SS TRA Code Approximate Inflated Dimensions Minimum Recoended Star OTD or Spec TKPH TMPH OD OW SLR SLW Dual Spacing Rim/Flange Height 46/90R57 VZTP 2 E4 E2A /6.0 Tubeless E1A (32.00/6.0) E3A VELS 2 E4 E2A E1A E3A VRDP 2 E4 E2A E1A E3A VRPS 2 E4 E2A E1A E3A /80R57 VSDL L5 D2A /6.0 Tubeless /90R57 VELS 2 E /6.5 Tubeless /6.5 E3A VRPS 2 E4 E2A E1A E3A /80R57 VSDL L5 D2A /6.0 Tubeless " 53/80R63 VRF 2 E TBA TBA /5.0 Tubeless TBA TBA 64.0 E3A VRDP 2 E4 E2A E1A E3A VRPS 2 E4 E2A E1A E3A /80R63 VRF 2 E /5.0 Tubeless E1A E3A /5.0 E1A E3A VRPS 2 E4 E2A /5.0 E1A E3A E2A /5.0 E1A E3A For the TKPH(TMPH) s of Radial Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. 5) To obtain the TKPH(TMPH) for type 2ALS, multiply type 2A rating by 0.8. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VZTP E/M 2 VELS 50 kg VRDP 30 lbs VRPS VSDL Loader 10 kg * About some exceptions, consult a 5 lbs bridgestone representative. VELS E/M 2 VRPS 50 kg lbs VSDL Loader 10 kg lbs " VRF E/M 2 VRDP 50 kg VRPS 30 lbs VRF 2 VRPS kg * 44.00/5.0 Rim lbs kg * 41.00/5.0 Rim lbs For the Load and Inflation Pressure Tables of Radial Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph) 2) Figures under the star rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page /90R /80R57 50/90R57 60/80R57 53/80R63 59/80R63 44 RADIAL TIRE 45

26 Tire LI/SS Star TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height Industrial 20" 12.00R20 VCH 3 Industrial V VCHS 176A5 3 Industrial " 12.00R24 VCH 2 Industrial V New VCHS Industrial R24 VHB 3 Industrial W VCH 3 Industrial VCHS 196A5 3 Industrial R24 TG VCHS 196A5 3 Industrial 10.00VA Tubeless 25" 16.00R25 VHB 2 Industrial /2.0 Tubeless VCHD 2 Industrial VRLS 2 Industrial R25 VHB 3 Industrial /2.5 Tubeless VEL 3 Industrial VCHS 214A5 3 Industrial VSMS 2 Industrial R25 VSDL 2 Industrial /2.5 Tubeless " 18.00R33 VCHS 219A5 3 Industrial /2.5 Tubeless VELS 3 Industrial /65R33 VSDL 2 Industrial /3.5 Tubeless OfftheRoad Tires Used for Industrial Vehicle s 1) Industrial Vehicles comprise vehicles such as counterbalanced lift trucks, container handlers, straddle carriers, aircraft tow tractors, mobile crushers, log stackers etc., used on hard improved surfaces, smooth floors and runways. 2) Use Specifications of Industrial only. Star Inflation Pressure Tire Load Limits at Various Speeds Industrial 20" kpa km/h 0 Creep psi mph Static Creep VCH IDU 3 Load 1000 kg VCHS Wheel 145 lbs Steering 1000 kg Wheel 145 lbs " VCH IDU 2 Load 960 kg Wheel 139 lbs Steering 960 kg Wheel 139 lbs VCHS IDU Load 1000 kg *Compliant with the ETRTO Wheel 145 lbs standard of industrial tires Steering 1000 kg Wheel 145 lbs VHB IDU 3 Load 1000 kg VCH Wheel 145 lbs VCHS Steering 1000 kg Wheel 145 lbs VCHS IDU 3 Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs " VHB IDU 2 Load 960 kg VCHD Wheel 139 lbs VRLS Steering 960 kg Wheel 139 lbs VHB IDU 3 Load 1000 kg VEL Wheel 145 lbs VCHS Steering 1000 kg Wheel 145 lbs VSMS IDU 2 Load 960 kg Wheel 139 lbs Steering 960 kg Wheel 139 lbs VSDL IDU 2 Load 690 kg Wheel 100 lbs Steering 690 kg Wheel 100 lbs " VCHS IDU 3 Load 1000 kg VELS Wheel 145 lbs Steering 1000 kg Wheel 145 lbs VSDL IDU 2 Load 780 kg Wheel 113 lbs Steering 780 kg Wheel 113 lbs ) Consult a Rim Manufacturer when inflation pressure exceeds 800kPa (116psi). 4) For Speeds exceeding 30km/h (18mph), consult a Bridgestone Representative. 5) For tire sizes and star ratings other than listed above, consult a Bridgestone Representative. 35/65R R R R R R24 TG 14.00R R R20 46 RADIAL TIRE 47

27 Tire LI/SS TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height Mobile Crane (HighSpeed) 21" 24R21 VGT Mobile Crane /1.5 Tubeless " 385/95R24 VSB 170E Mobile Crane W (14.00R24) VHB 170E Mobile Crane VHS 170E Mobile Crane " 385/95R25 VSB 170E Mobile Crane /1.5 (14.00R25) Tubeless VHS 170E Mobile Crane F VSW 170E Mobile Crane /95R25 VHB 177E Mobile Crane /2.0 (16.00R25) Tubeless VHS 177E Mobile Crane F VSW 177E Mobile Crane /80R25 VGT 170E Mobile Crane /1.5 (17.5R25) Tubeless 505/95R25 VHB 186E Mobile Crane /2.5 (18.00R25) Tubeless VHS 186E Mobile Crane /80R25 VHS 179E Mobile Crane /2.0 (20.5R25) Tubeless Inflation Pressure Tire Load Limits at Various Speeds Mobile Crane (HighSpeed) *Consult a Rim Manufacturer when inflation pressure exceeds 800kPa (116psi). 21" kpa km/h 88 psi mph 55 VGT HighSpeed 580 kg lbs " kpa km/h 0 Creep psi mph Static Creep VSB HighSpeed 900 kg VHB 131 lbs VHS 25" VSB HighSpeed 900 kg VHS 131 lbs VSW (170E) VHS HighSpeed 900 kg (170F) 131 lbs VHB HighSpeed 900 kg VHS 131 lbs VSW (177E) VHS HighSpeed 900 kg (174F) 131 lbs VGT HighSpeed 700 kg lbs VHB HighSpeed 900 kg VHS 131 lbs VHS HighSpeed 700 kg lbs R21 385/95R24 (14.00R24) 385/95R25 (14.00R25) 445/95R25 (16.00R25) 445/80R25 (17.5R25) 505/95R25 (18.00R25) 525/80R25 (20.5R25) 48 RADIAL TIRE 49

28 Tire LI/SS Star TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height Sand 20" 16.00R20 VSJ 28 E W " 21.00R25 VSJ E /3.0 Tubeless Ply Max. Speed Tire Cold Inflation Pressures at Various Load Limits Sand *It is Recoended that 90% of the below indicated loads per tire is to be applied when used on a dual axle. 20" kg lbs VSJ Sand 28PR 65km/h kpa mph psi km/h kpa mph psi km/h kpa mph psi " VSJ Sand 65km/h kpa mph psi km/h kpa mph psi km/h kpa mph psi R R25 50 RADIAL TIRE 51

29 4. Remarks 4.1 Excess Load Due to the specialized nature of OffTheRoad vehicle usage, loads in excess of those in the appropriate abovelisted load tables are often encountered. These excess loads result from items such as actual vehicle weight exceeding the design weight, varying density of materials, field modifications to the equipment, load transfer, etc. Only under these conditions, the actual tire load in service may exceed the above load ratings for the tire(*) by an amount not greater than shown in the following table: E2, E3, E4* L** Maximum Excess Load 7% 7% Maximum Excess Pressure 14% 14% Maximum Pressure (except for underground vehicles) When excess loads are encountered, cold inflation pressures must be increased to compensate for higher loads. For each 1% increase in load, the inflation pressure must be increased by 2%. *except following sizes on the list 11.00R20 335/80R20 405/70R R R20 365/80R20 12R22.5 *About 63" tires, consult a Bridgestone represetative. **except 55.5/80R57 and 60/80R57 The maximum excess loads will result in reduced tire performance. 4.2 The Variation in Load Carrying Capacity with Operating Speed Operating Speed (km/h) Static Creep < 800kPa 116psi E2, E3 E4 G L** 825kPa 120psi +60% * +30% +14% 0 +12% 13% +10% +8% 20% +6% +4% 26% +3% 0 30% +2% 0 9% 2% 6% 18% 12% 27% 20%* * 30%* * 42%* * * * Reference speed for calculating load variance * Consult a Bridgestone Representative ** About the size of 55.5/80R57 and 60/80R57, consult a Bridgestone representative. 4.3 LoadandCarry Operations for Front End Loader conditions of a loader is defined as picking up material and relocating a short distance away, a maximum of 76m (250 feet), one way, with a maximum speed of 10km/h (5mph). However, a loader can pick up a load and transport such load to another location and return unloaded for a longer distance. This type of service is called LoadandCarry operations. Transportation usually occurs at low speeds, up to 25km/h (15mph), and distances are limited. The tires when used in LoadandCarry operations may encounter heat problems especially on the front axle tires. To avoid such problems, Bridgestone recoends the following operating conditions. For tires over 33" rim diameter tires, careful study is required to maximize tire life while considering Ton KilometerPerHour (TonMilePerHour) limits. Please consult Bridgestone representative for more information. If you need to use the tire beyond this recoendation, please consult Bridgestone representative. For Radial Tires Tread Class Conventional size (95 series) Inflation Pressure Rim Diameter 29" and below 33" and above Wide base size (85, 65 series) Wide base size (65 series) Load Capacity* 10km/h (5mph) Maximum Cycle Distance (m) Allowable Average Workshift Speed (km/h) L2, L L kpa 825kpa 500kpa 650kpa 600kpa 750kpa 100% of 1500 (VSDT) 10 L5 (80psi) (120psi) (73psi) (94psi) (87psi) (109psi) STD.load 1200 (VSDL) 6 L5S * STD.load: Maximum permissible load at standard inflation pressure for respective tire size and star rating. Please refer to the load inflation pressure table for loader and dozer service 10km/h (5mph) service. This table doesn't secure to prevent the risk derived from heat buildup. 52 RADIAL TIRE 53

30 BIAS TIRE 1. Tread Designs Earthmover E3 E4 L4 L5 L5S WLUG RLUG VLUG2 RLUG S ELUG S2 (WL) (RL) (VL2) (RLS) (ELS2) RLUG S NLUG DLUG SMOOTH TREADMS (RLS) (NL) (DL) (STMS) Sand Grader Compactor Logging E7 G1 G2 C1 C2 LS2 SAND CLIPPER2 RIB GRADER GLUG FAST GRIP (SCP2) (RG) (GL) (FG) G3 Loader & Dozer L2 L3 ROAD ROLLER ALLIGATOR2 TIMBER GRIP S (RR) (AL2) (TGS) Industrial RLUG GLUG FAST GRIP RLUG VLUG2 (RL) (GL) (FG) (RL) (VL2) RLUG RLUG S ELUG S2 SMOOTH TREADMS YARD SERVICE2 (RL) (RLS) (ELS2) (STMS) (YS2) 54 BIAS TIRE 55

31 2. Earthmover Grader HEAT RESISTANT CUT RESISTANT HEAT RESISTANT CUT RESISTANT TRACTION GL FG TRACTION WL RL VL2 RLS ROCK RG RL ROCK ELS2 Type Ply Type Ply Type Ply WL(E3) T/T 14 RL(E3) T/T T/T T/T T/T T/T T/L T/L T/L 36 VL2(E3) T/L T/L T/L T/L RLS(E4) T/L 32 ELS2(E4) T/L 32 RG(G1) T/T 10 GL(G2) T/T 14 FG(G2) TG T/L 12 T/T TG T/L 14 T/T TG T/T T/L T/L 12 T/T 12 RL(G3) TG T/T 16 T/T: Tube Type T/L: Tubeless Type T/T: Tube Type T/L: Tubeless Type TG: For SemiDrop Center Rim 56 BIAS TIRE 57

32 Loader & Dozer HEAT RESISTANT CUT RESISTANT HEAT RESISTANT CUT RESISTANT TRACTION TRACTION GL FG FGF RL VL2 RLS ROCK NL DL STMS ROCK GL(L2) Type Ply Type Ply T/T 14 FG(L2) 23x T/T 4 27x T/T 4 33x T/T /7016 T/L T/L T/L 8 10 T/T /6018 T/L /7018 T/L T/T T/T /7020 T/L 10 42x1720 T/T /6520 T/L TG T/L 12 T/T TG T/L T/T T/T T/T T/L T/L T/L 12 T/T 12 FGF(L2) T/T 16 RL(L3) T/T T/T TG T/L TG T/T 16 T/T: Tube Type T/L: Tubeless Type TG: For SemiDrop Center Rim Type Ply Type Ply Type Ply VL2(L3) NL(L4) STMS(L5S) T/L T/L 16 T/T T/L T/T T/L T/T T/L T/T T/L RLS(L4) T/T T/L T/L T/L 28 T/T: Tube Type T/L: Tubeless Type 35/6533 T/L DL(L5) T/L T/L T/L T/L T/L 28 35/6533 T/L 42 40/6539 T/L /7039 T/L 42 45/6545 T/L 58 50/6551 T/L 62 65/6557 T/L T/T T/T T/L T/L T/L T/L BIAS TIRE 59

33 Compactor Type Ply Industrial Type Ply RR(C1) RL RR T/T /6515 T/T T/L 6 T/T /8016 T/L T/T 10 14/7020 T/T 12 RL T/T T/T TG T/L T/L T/T T/L T/L T/L 40 AL2(C2) T/L 8 T/T 8 RLS TG T/L T/L AL2 RLS ELS2 Logging ELS T/L T/L T/L 40 TGS(LS2) 30.5L32 T/T 16 STMS TGS T/T T/L 40 STMS YS T/L 32 Sand YS2 SCP2(E7) T/T 18 SCP2 T/T: Tube Type T/L: Tubeless Type T/T: Tube Type T/L: Tubeless Type TG: For SemiDrop Center Rim 60 BIAS TIRE 61

34 3. Technical Data Tire Ply TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 12" 23x FG 4 L JA " RR 12 C GS x FG 4 L JA /6515 RR 6 C JA x FG 8 L TBA* TBA* F TBA* TBA* 16" RR 6 C GS Tubeless LB Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 12" kpa psi FG Loader PR 4 10 kg lbs " kpa psi RR Compactor PR kg lbs kpa psi FG Loader PR 4 10 kg lbs RR Compactor PR 6 10 kg lbs kpa psi FG Loader PR 8 10 kg lbs " RR Compactor C1 PR 6 10 kg lbs x / x x /8016 RR 6 C LB Tubeless /7016 FG 6 L LB Tubeless " FG 6 L Tubeless FG 8 L Tubeless RR PR 6 kg lbs FG Loader PR kg lbs " FG Loader PR kg lbs FG PR 8 10 kg lbs / /8016 *Due to factory transfer. For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page BIAS TIRE 63

35 Tire Ply TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 18" 15.5/6018 FG 8 L W10 Tubeless /7018 FG 8 L W13 Tubeless " RG 10 G T RR 10 C GL 14 G2,L WL 14 E3 SCR FG 10 L V FGF 16 L RL 14 E3 CRT FG 10 L V RL 14 E3 CRT For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 18" kpa psi FG Loader PR 8 10 kg lbs FG PR 8 kg lbs " RG Grader PR GL 40 kg lbs kpa psi RR Compactor PR kg lbs GL Loader PR kg lbs kpa psi WL E/M PR kg lbs kpa psi FG Loader PR FGF 10 kg lbs kpa psi RL E/M PR kg lbs kpa psi FG Loader PR kg lbs kpa psi RL E/M PR kg lbs For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page / / BIAS TIRE 65

36 Tire TRA Code Approximate Inflated Dimensions Minimum Recoended Ply OTD Dual Spacing Rim/Flange Height or Spec TKPH TMPH OD OW SLR SLW RL 18 E3 SCR V Industrial IDU SCP2 18 E7 See characteristics page 78 See characteristics page 80 14/7020 RR 12 C TG /7020 FG 10 L TBA* TBA* 21.5 W13 Tubeless TBA* TBA* 42x1720 FG 10 L TBA* TBA* TG TBA* TBA* 17.5/6520 FG 10 L TBA* TBA* 25.0 W14L Tubeless TBA* TBA* 24" RL 20 E3 DE L V 16 D2A STMS 16 L5S D2A V Industrial IDU See characteristics page TG FG 12 G2 DG TG Tubeless L (10.00VA) TG 10 G2 G2A 12 L2 D2A *Due to factory transfer. For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi RL E/M PR kg lbs RL IDU See characteristics page 79 SCP2 Sand See characteristics page 81 kpa psi RR Compactor PR kg lbs FG Loader PR kg lbs FG Loader PR kg lbs FG Loader PR kg lbs " kpa psi RL E/M PR kg lbs kpa psi RL Loader PR STMS 10 kg lbs STMS IDU See characteristics page 79 kpa psi FG Grader PR kg lbs FG Loader PR kg lbs For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page TG / x / / BIAS TIRE 67

37 Tire TRA Code Approximate Inflated Dimensions Minimum Recoended Ply OTD Dual Spacing Rim/Flange Height or Spec TKPH TMPH OD OW SLR SLW RL 28 E3 E2A W L3 D2A Industrial IDU 28 See characteristics page 78 RLS 20 L4 D2A W STMS 20 L5S D2A TG FG 14 G2 G2A TG Tubeless (10.00VA) 12 L2 D2A TBA TBA 10.00VA TBA TBA RL 12 L3 D2A VA D2V (8.00TG) 24 Industrial IDU RLS 24 Industrial IDU See characteristics page TG FG 12 G2 G2A TG (10.00VA) Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi RL E/M PR kg lbs kpa psi RL Loader PR RLS 10 kg STMS 5 lbs RL IDU See characteristics page 79 kpa psi FG Grader PR kg lbs FG Loader PR RL 10 kg lbs RL IDU RLS See characteristics page TG VA (8.00TG) 12 L2 D2A TBA TBA 10.00VA TBA TBA TG FG 16 G2 G2A VA RL 16 G3, L3 DG FG 10 L W15L FG 10 L W16L " FG 12 L2 D2A /1.3 Tubeless VL2 12 L3 D2A FG Grader PR 16 RL 40 kg lbs RL Loader PR kg lbs kpa psi FG Loader L2 PR kg lbs FG L2 PR 10 kg lbs " kpa psi FG Loader PR 12 VL2 10 kg lbs TG For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page BIAS TIRE 69

38 Tire TRA Code Approximate Inflated Dimensions Minimum Recoended Ply OTD Dual Spacing Rim/Flange Height or Spec TKPH TMPH OD OW SLR SLW RL 28 E3 E2A /2.0 Tubeless Industrial IDU 32 RLS 28 Industrial IDU 32 Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi RL E/M PR kg lbs RL IDU RLS YS YS2 32 Industrial IDU See characteristics page 78 See characteristics page RL 28 Industrial IDU FG 12 G2, L2 DG /1.5 Tubeless VL2 16 L3 D2A DL 16 L5 D2A STMS 20 L5S D2A D2Z VL2 16 L3 D2A RL 32 E3 E2A /2.5 Tubeless Industrial IDU 40 ELS2 40 Industrial IDU See characteristics page 78 STMS 24 L5S D2A / Industrial IDU See characteristics page 78 kpa psi FG Grader PR kg lbs For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. For extreme conditions, consult a Bridgestone Representative for additional recoended operating requirements. kpa psi FG Loader PR VL2 10 kg DL 5 lbs STMS RL E/M PR kg lbs kpa psi STMS Loader PR kg lbs RL IDU ELS2 STMS See characteristics page For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page BIAS TIRE 71

39 Tire TRA Code Approximate Inflated Dimensions Minimum Recoended Ply OTD Dual Spacing Rim/Flange Height or Spec TKPH TMPH OD OW SLR SLW FG 12 G2, L2 DG /1.7 Tubeless (12,16PR) 17.00/2.0 VL2 16 E3 DE L DL 12 L5 D2A FG 12 G2, L2 DG VL2 16 L3 D2A RL 40 Industrial IDU Tubeless See characteristics page VL2 16 E3 DE /2.5 Tubeless 20 L D2A RLS 16 L4 D2A DL 20 L5 D2A VL2 16 L3 D2A For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VL2 E/M PR kg lbs FG Grader PR kg lbs FG Loader PR VL2 10 kg DL 5 lbs RL IDU For slope and ditching service, inflation pressures should be increased by 100kPa (15psi) with no increase in load rating. For extreme conditions, consult a Bridgestone Representative for additional recoended operating requirements. See characteristics page 79 kpa psi VL2 Loader PR RLS 10 kg DL 5 lbs VL2 E/M PR kg lbs For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page BIAS TIRE 73

40 Tire TRA Code Approximate Inflated Dimensions Minimum Recoended Ply OTD Dual Spacing Rim/Flange Height or Spec TKPH TMPH OD OW SLR SLW VL2 20 E3 DE /3.0 Tubeless 24 L D2A 24 RLS 26 L4 D2A DL 20 L5 D2A Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures kpa psi VL2 E/M PR kg lbs VL2 Loader PR RLS 10 kg DL 5 lbs STMS STMS 32 L5S D2A VL2 20 L3 D2A VL2 22 E3 DE /3.5 Tubeless 28 L RLS 28 L4 D2A DL 28 L5 D2A " AL2 8 C DW20A Tubeless DW20B AL2 8 C " STMS 34 L5S D2A /3.5 Tubeless D2Z " 30.5L32 TGS 16 LS2 S2V DW27A DW27B For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. VL2 E/M PR kg lbs VL2 Loader PR 28 RLS 10 kg DL 5 lbs " kpa 110 psi 16 AL2 Compactor PR 8 10 kg lbs " kpa psi STMS Loader PR kg lbs " kpa psi TGS Logging PR 16 32km/h(20mph) Maximum Speed kg lbs PR 16 16km/h(10mph) Maximum Speed kg lbs For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page L BIAS TIRE 75

41 Tire Ply TRA Code or Spec TKPH TMPH Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 33" RLS 32 E4 E2A /2.5 Tubeless ELS2 32 E4 E2A Industrial IDU See characteristics page 78 35/6533 NL 24 L4 D2V /3.5 Tubeless DL 42 L5 D2V Max.Speed km/h mph Tire Load Limits at Various Cold Inflation Pressures 33" kpa psi RLS E/M PR 32 ELS2 50 kg lbs ELS2 IDU See characteristics page 79 NL Loader PR DL 10 kg lbs / " RL 40 Industrial IDU Tubeless ELS2 40 Industrial IDU See characteristics page 80 35" RL ELS2 IDU See characteristics page RL 36 E3 E1A /4.0 Tubeless " 40/6539 DL 56 L5 D2V /4.0 Tubeless /7039 DL 42 L5 D2V /4.5 Tubeless " 45/6545 DL 58 L5 D2V /4.5 Tubeless " 50/6551 DL 62 L5 D2A /4.5 Tubeless D2V " 65/6557 DL 62 L5 D2V /6.0 Tubeless For the TKPH(TMPH) s of Bias Tires 1) The figures are at 38 C (or 100 F) ambient temperature. If the ambient temperature is over 38 C (or 100 F), consult a Bridgestone Representative. 2) If the roundtrip distance is less than 5km (or 3 miles), the above ratings can be increased by 12%. 3) If the Maximum Speed exceeds 50km/h (or 30 mph), consult a Bridgestone Representative. 4) When haul length exceeds 16km (10miles) one way, consult a Bridgestone Representative. kpa psi RL E/M PR kg lbs " kpa psi DL Loader L5 PR kg lbs DL L5 PR 42 kg lbs " DL Loader PR kg lbs " DL Loader PR kg lbs " DL Loader PR kg lbs For the Load and Inflation Pressure Tables of Bias Tires 1) Maximum Speeds are as below. Earthmover : 50km/h (30mph), Grader : 40km/h (25mph), Loader & Dozer : 10km/h (5mph), Compactor : 10km/h (5mph) 2) Figures under the ply rating denote the maximun load and inflation pressures. 3) For Loader & Dozer, Dig & Load Operation or distances are up to 76m (250ft) one way. 4) For Load & Carry operations, tire load limit will be adjusted following the table of page / / / / / BIAS TIRE 77

42 Tire Ply TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height Industrial 20" RL 20 Industrial V " STMS 20 Industrial V RL 24 Industrial W TG RL 24 Industrial VA Tubeless RLS 24 Industrial " RL 28 Industrial /2.0 Tubeless RLS 28 Industrial YS2 32 Industrial RL 28 Industrial Appli. Ply Inflation Pressure Tire Load Limits at Various Speeds Industrial 20" kpa km/h 0 Creep psi mph Static Creep RL IDU 20 Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs " STMS IDU 20 Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs RL IDU 24 Load 1000 kg RLS Wheel 145 lbs Steering 1000 kg Wheel 145 lbs Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs " RL IDU 28 Load 900 kg RLS Wheel 131 lbs YS2 Steering 900 kg Wheel 131 lbs Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs RL 36 Industrial /2.5 Tubeless ELS2 40 Industrial STMS 40 Industrial RL 40 Industrial /3.0 Tubeless " ELS2 36 Industrial /2.5 Tubeless RL IDU 36 Load 1000 kg ELS2 Wheel 145 lbs STMS Steering 1000 kg Wheel 145 lbs Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs RL IDU 40 Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs " ELS2 IDU 36 Load 1000 kg Wheel 145 lbs Steering 1000 kg Wheel 145 lbs BIAS TIRE 79

43 Tire Ply TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height 35" RL 40 Industrial /3.0 Tubeless ELS2 40 Industrial Appli. Ply Inflation Pressure Tire Load Limits at Various Speeds 35" kpa km/h 0 Creep psi mph Static Creep RL IDU 40 Load 1000 kg ELS2 Wheel 145 lbs Steering 1000 kg Wheel 145 lbs OfftheRoad Tires Used for Industrial Vehicle s 1) Industrial Vehicles comprise vehicles such as counterbalanced lift trucks, container handlers, straddle carriers, aircraft tow tractors, mobile crushers, log stackers etc., used on hard improved surfaces, smooth floors and runways. 2) Use Specifications of Industrial only. 3) Consult a Rim Manufacturer when inflation pressure exceeds 800kPa (116psi). 4) For Speeds exceeding 30km/h (18mph), consult a Bridgestone Representative. 5) For tire sizes and star ratings other than listed above, consult a Bridgestone Representative. 6) For RTG (Rubber Tired Gantry Crane) operation, consult a Bridgestone Representative. Tire Ply TRA Code or Approximate Inflated Dimensions OD OW SLR SLW OTD Minimum Dual Spacing Recoended Rim/Flange Height Sand 20" SCP2 18 E TBA* TBA* V TBA* TBA* *Due to factory transfer. Appli. Max. Speed Tire Load Limits at Various Cold Inflation Pressures (100kPa = 1bar) Sand When tires are to be used under conditions other than those recoended above, consult a Bridgestone Representative. 20" kpa psi SCP2 Sand 10km/h kg mph lbs km/h kg mph lbs km/h kg mph lbs BIAS TIRE 81

44 4. Remarks 4.1 Excess Load Due to the specialized nature of OffTheRoad vehicle usage, loads in excess of those in the appropriate abovelisted load tables are often encountered. These excess loads result from items such as actual vehicle weight exceeding the design weight, varying density of materials, field modifications to the equipment, load transfer, etc. Only under these conditions, the actual tire load in service may exceed the above load ratings for the tire(*) by an amount not greater than shown in the following table: E2, E3, E4* L** L5/L5S*** Maximum Excess Load 15% 15% 0% Maximum Excess Pressure 30% 30% +100kPa Maximum Pressure 825kPa 825kPa 120psi 120psi (except for underground vehicles) When excess loads are encountered, cold inflation pressures must be increased to compensate for higher loads. For each 1% increase in load, the inflation pressure must be increased by 2%. *except following sizes on the list **except following sizes on the list x / / x / / / x / x *** For L5/L5S tyres following sizes on the list, on front tires for front end loaders, it is permissible to increase inflation pressure up to 100kPa (15psi) above, with no increase in load. (Maximum inflation pressure should not exceed 825 kpa (120psi).) / / / / / /6557 The maximum excess loads will result in reduced tire performance. 4.2 The Variation in Load Carrying Capacity with Operating Speed Operating Speed (km/h) Static Creep < E2, E3, E4** G L*** **except following sizes on the list ***except following sizes on the list +60% * +30% +14% 0 +12% 13% +10% +8% 20% +6% +4% 26% +3% 0 30% +2% 0 9% * * 18% * 27% * * * * x / / x / / / x / x This table doesn't secure to prevent the risk derived from heat buildup. Reference speed for calculating load variance * Consult a Bridgestone Representative 4.3 LoadandCarry Operations for Front End Loader conditions of a loader is defined as picking up material and relocating a short distance away, a maximum of 76m (250 feet), one way, with a maximum speed of 10km/h (5mph). However, a loader can pick up a load and transport such load to another location and return unloaded for a longer distance. This type of service is called LoadandCarry operations. Transportation usually occurs at low speeds, up to 25km/h (15mph), and distances are limited. The tires when used in LoadandCarry operations may encounter heat problems especially on the front axle tires. To avoid such problems, Bridgestone recoends the following operating conditions. For tires over 33" rim diameter tires, careful study is required to maximize tire life while considering TonKilometer PerHour (TonMilePerHour) limits. Please consult Bridgestone representative for more information. If you need to use the tire beyond this recoendation, please consult Bridgestone representative. For Bias Tires Load Capacity** Tread Inflation Pressure 10km/h (5mph) Maximum Cycle Allowable Average Class for Front Tires Distance Workshift Speed Rim Diameter (m) (km/h) 29" and below 33" and above L2, L3 Standard inflation 85% of L4 pressure 90% of STD. load 500 L5 + STD. load L5S 100kpa (15psi) *** ** STD.load: Maximum permissible load at standard inflation pressure for respective tire size and star rating. Please refer to the load inflation pressure table for loader and dozer service 10km/h (5mph) service. ***Not permissible The inflation pressure should not exceed 825kPa (120psi). 82 BIAS TIRE 83

45 OTHER SPECIFICATION 1. ORing Specifications 3. Rim and Valve Code No. P24A P25AX P25B P29B Applicable Radial Bias 13.00R24 TG TG 14.00R24 TG TG 16.00R24 TG 14.00R25* 15.5R R R R25 385/95R25 445/80R25 445/95R R25** 16.00R R R R R R /65R R R /65R25(750/65R25) 385/95R25 445/80R25 445/95R25 505/95R25 525/80R25 550/65R25 600/65R25 650/65R25 750/65R R R29 775/65R29 875/65R29 Diameter Inner Circumference Code No. P33B P35B P39B P45B P49B P51C P57C P63C Radial 18.00R R33 35/65R R R R R R R /75R39 45/65R39 45/65R R R49 31/90R R R R51 50/65R R R57 42/90R57 46/90R57 50/90R /80R57 60/80R57 53/80R63 59/80R63 Applicable Bias / / / / / /6557 Inner Diameter Circumference * For Rim ** For Rim Rim Flange Rim Width Rim Base Rim Flange BeadSeat Band Lock Ring 2. Flap Specifications Bead Seat Locking Key (part of lock ring) Flap DB G1 P 550/ /700/ /65B /825AR /825R D1000R A825R A111R B13/80R /14/80R A x / A140024, B1300R /140024, /1600R24, , A180024, R P G1 DB ORing Flap Nominal Diameter Valve Hole 8.50V 24 ValveStem Support Nominal Diameter of Rim (es) Flange Type Rim Width (es) 84 OTHER SPECIFICATION 85

46 3.1 Rim Designation Full Tapered Bead Seat Rims (5 pieces) Full Tapered Bead Seat Rims (3 pieces) Semi Drop Center Rims (SDC) Flat Base Rims A B D E Recoended Rim/ Flange Height 11.00/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /6.0 Radial 14.5R R25 445/95R25(16.00R25) 18.00R25 505/95R25(18.00R25) 18.00R R R R35 550/65R25 600/65R R R49 24R R25 600/65R25 650/65R R49 31/90R49 25/65R25 750/65R25(30/65R25) 26.5R R51 750/65R25(30/65R25) 775/65R R R25 775/65R R R R51 875/65R R R R57 42/90R57 875/65R29 35/65R R57 46/90R R R /75R39 45/65R39 50/90R57 50/90R57 45/65R39 45/65R45 53/80R63 50/65R51 59/80R63 59/80R /80R57 60/80R57 Tire Bias / / / / / /6557 Recoended Rim/ Flange Height 10.00/ / / / AL/1.7( 1only) 17.00/1.7 C 17.00/2.0 Recoended Rim/ Flange Height 5JA 4.50E 5.1/2K 5.50F 7JA 11LB 6LB 8LB 10LB W13 W14L W15L DW20B DW27B Radial 14.00R25 385/95R25(14.00R25) 15.5R R25 445/80R25(17.5R25) 550/65R25 550/65R R25 600/65R R25 525/80R25(20.5R25) Tire Drop Center Rims (DC, W, DW) Radial Tire Bias Bias 23x x x / / / / / / / L32 Recoended Rim/ Flange Height 86 OTHER SPECIFICATION GS 8.00TG 10.00F 10.00VA 11x TG 13x TG A Radial 13.00R24 TG 14.00R24 TG 16.00R24 TG 335/80R20 365/80R20 405/70R20 Tire Bias TG 33x TG TG TG 14/ x1720 Recoended Rim/ Flange Height 6.50T 7.00T 7.50V 8.00V V V 10.00WI 10.00W C D E B Radial 8.25R R R R R R24 12R R R R24 385/95R24(14.00R24) 385/95R25(14.00R25) Tire Bias

47 3.2 Valve Types Interchangeable Swivel Valves For Tubeless Or Tube Type Tires TRJ /2 Large Bore Valves Tube Valve and Rim Section Flap Tube A F B Valve No. TRJ650 TRJ /2 TRJ40008 TRJ /2 Dimensions () A B F This type of VALVE consists of a combination of the rubber base SP4000 or SP2. Tubeless Type Spud SP2 Tube Type Spud SP4000 Tubeless Valve and Rim Section Tube Valve Inner Liner Tube Type Rubber Base Valves ø114 TR218 Rim Valve A B 9.5 Valve No. TR218A Dimensions () A B Tube Valve TR220A ø63.5 PV7 B 86 Tubeless Valve A Valve No. A Dimensions () B C D dia. PV C 88 OTHER SPECIFICATION 89 D dia.

48 Tube Type Rubber Covered Valves JS75 A ø95 F ± 2 B Valve No. JS75 TR76A TR77A TR77E TR78A TR175A TR177A JS177B JS179 JS179A TR179A PV38 PV89 V3023 V30215 Dimensions () A B F TR13 38 E ø56 Valve No. TR13 TR15 Dimensions () E Tube Type Screwon Valves PV88 B D G JSJ F F ± 2 B A C Large Bore Valves A Valve No. JSJ1078S JSJ1175 JSJ1175B JSJ1175C Dimensions () A B D dia. F ø95 Valve No. V3062 V3065 PV88 PV118 A Dimensions () B C D F G D dia. TR150CW ø15.5 JS2 F B 88.5 A Valve No. JS2 Dimensions () A 26 B 33 F 70 Valves, TR150 and TR150CW, are also called Hand Bendable Valves, that is, their stems are made of very flexible material permitting manual bending in all directions and to any angle. 90 OTHER SPECIFICATION 91 ø57

49 OTHER INFORMATION 1. Unit Conversion Tables INFLATION PRESSURE WEIGHT (FROM POUND TO KILOGRAM) kg/cm 2 lb/in 2 kpa bar kg/cm 2 lb/in 2 kpa bar lb kg lb kg lb kg lb kg kg/cm 2 lb/in 2 kpa bar kg/cm 2 lb/in 2 kpa bar WEIGHT (FROM KILOGRAM TO POUND) kg lb kg lb kg lb kg lb TEMPERATURE (CENTIGRADE/FAHRENHEIT) C F C F C F C F C F C F PRESSURE kg/cm 2 kpa bar psi kg/cm kpa bar psi OTHER INFORMATION 93

50 LENGTH m.meter c.meter meter k.meter foot yard mile AREA meter 2 are hectare k.meter 2 foot 2 yard 2 acre mile 2 m.meter c.meter meter k.meter foot yard mile meter 2 are hectare k.meter 2 foot 2 yard 2 acre mile Specific Weight (Approximately) Material Pounds/cu.yd Metric Tons/m 3 Material Pounds/cu.yd Metric Tons/m 3 Anthracite Iron ore: Magnetite Basalt Limestone Bauxite Pyrites Clay: dry OverBurden wet %rock25%earth Coal %rock50%earth Copper ore %rock75%earth Crushed gypsum Sand: dry Earth: dry wet wet Sandstone Granite Snow: dry Gravel: dry wet wet Uranium Note: Weight of materials varies with moisture content, grain size, degree of compaction, etc. Test must be made to know exact weight. WEIGHT gram k.gram ton s.ton l.ton ounce pound gram k.gram ton s.ton l.ton ounce pound CAPACITY cub.meter liter cub. cub.foot cub.yard U.S.gallon U.K.gallon cub.meter liter cub. cub.foot cub.yard U.S.gallon U.K.gallon FORCE 1 kgf = 9.81 N POWER (horse power) 1 hp = 550 ft lbf/s = W 1 PS = 75 m kgf/s = W 94 OTHER INFORMATION 95

51 MEMO

52