ASSEMBLY MANUAL VERSION /2013

Size: px

Start display at page:

Download "ASSEMBLY MANUAL VERSION /2013"

Claud John Wilkins
5 years ago
Views:

1 ASSEMBLY MANUAL VERSION /2013 Copyright by FLY Products s.r.l. Via Perù n GROTTAMMARE (AP) - ITALY tel./fax fly@flyproducts.com

2 INDEX 1 FRAME ASSEMBLY 2 HARNESS SIZE ADJUSTMENT 3 FITTING THE HARNESS HIGH ATTACK 4 5 FITTING THE HARNESS LOW ACTIVE ATTACK (ACTIVE LOW HANG POINT) OPTIONAL FITTING THE HARNESS FIXED (FIXED HANG POINT) OPTIONAL 6 PROP MOUNTING 7 MULTIFUNCTION HANDGRIP 8 WARRANTY Copyright by FLY PRODUCTS s.r.l. Pag. 2

3 1 FRAME ASSEMBLY Photo frame Assembly common to paramotors: Thrust, Race c, Kompress, Sprint, Jet. Step 1: assembling the outer frame Supports Starter manual section (only manual starter) Support Assembly Step 2: Assembling the top section of the external frame Assemble the two semicircles Assemble the cage from top grafts Continue side grafting over and then the lower teeth on each side Copyright by FLY PRODUCTS s.r.l. Pag. 3

4 Punto 3 : Bloccaggio dei velcri Upper Velcro Hook network cord on both sides Tighten the bottom with velcro tape on both sides Tighten the upper with velcro tape on both sides Copyright by FLY PRODUCTS s.r.l. Pag. 4

5 2 HARNESS SIZE ADJUSTMENT Find the most suited to your needs and verify in the Simulator Cut along the dotted line to get size M. Adjusting harness zip size M. Zip harness adjustment size L. A Position the harness shallower. B position the harness deeper Copyright by FLY PRODUCTS s.r.l. Pag. 5

3 FITTING THE HARNESS HIGH ATTACK La selletta viene fissata al telaio su tre punti di ancoraggio: in alto con due bulloni a farfalla, di lato con due

1) Upper hooks harness with two Butterfly bolts Attach the harness to the chassis with the plate and tighten the two bolts with the butterflies.

6 3 FITTING THE HARNESS HIGH ATTACK La selletta viene fissata al telaio su tre punti di ancoraggio: in alto con due bulloni a farfalla, di lato con due distanziali, in basso con due cinghie regolabili. 1) Upper hooks harness with two Butterfly bolts Attach the harness to the chassis with the plate and tighten the two bolts with the butterflies. ATTENTION Mount the plate as is indicated on the sticker of your paramotor Asymmetric distance bar for: Rider Thrust. Anticlockwise rotation of the propeller Asymmetric distance bar for: Rider Jet, Rider Race C, Clockwise rotation of the propeller Copyright by FLY PRODUCTS s.r.l. Pag. 6

2) Assembly of the distance bars Insert the distance

maximum length 4) Fastening shoulder webbing Attach

7 2) Assembly of the distance bars Insert the distance bar into the square slot located on the Central frame and close the Velcro straps. 3) Lateral belt attachment Fasten the webbing at maximum length 4) Fastening shoulder webbing Attach the webbing to the right and left of the frame Copyright by FLY PRODUCTS s.r.l. Pag. 7

4 ASSEMBLY OF (LOW ACTIVE HANG POINT) The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways with two distance bar and bottom with

ATTENTION Mount the plate as is indicated on the sticker of your paramotor 2) Fixing the frame distance bars Mount distance bars according to two regulations: Regulation 1: 1A =

8 4 ASSEMBLY OF (LOW ACTIVE HANG POINT) The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways with two distance bar and bottom with three belts. 1) Upper hooks harness with two Butterfly bolts Attach the harness to the chassis with the plate and tighten the two bolts with the butterflies. ATTENTION Mount the plate as is indicated on the sticker of your paramotor 2) Fixing the frame distance bars Mount distance bars according to two regulations: Regulation 1: 1A = Pilots over 85 kg. 1B = Pilots less 85 kg. Regulation 2: Direction 2A (forward) Heavy Pilots Direction 2B (back) Light Pilots 3) Bottom bracket of the frame with three straps Copyright by FLY PRODUCTS s.r.l. Pag. 8

9 Configuration for: Rider Sprint, Rider Race C, Rider Jet. Clockwise rotation of the propeller Configuration for: Rider Thrust. Anticlockwise rotation of the propeller Copyright by FLY PRODUCTS s.r.l. Pag. 9

5 ASSEMBLY OF: (FIXED HANG POINT) The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways with two distance bar and

ATTENTION Mount the plate as is indicated on the sticker of your paramotor 2) Assembly of the spacer bars Insert the distance bar into the square slot located on the

10 5 ASSEMBLY OF: (FIXED HANG POINT) The harness is fastened to the frame on three anchor points: at the top with two Butterfly bolts sideways with two distance bar and bottom with three belts. 1) Upper hooks harness with two Butterfly bolts Attach the harness to the chassis with the plate and tighten the two bolts with the butterflies. ATTENTION Mount the plate as is indicated on the sticker of your paramotor 2) Assembly of the spacer bars Insert the distance bar into the square slot located on the Central frame and secure them with bolts and butterflies Assemble the distance bar in one of two holes according to the pilot weight. Copyright by FLY PRODUCTS s.r.l. Pag. 10

Punto 3: Bottom bracket of the frame with

11 Punto 3: Bottom bracket of the frame with three straps Configuration for: Rider Sprint, Rider Race C, Rider Jet. Rotazione oraria dell elica Configuration for: Rider Thrust. Anticlockwise rotation of the propeller Copyright by FLY PRODUCTS s.r.l. Pag. 11

6 PROP MOUNTING Mount the propeller on the motor with belt reduction: Rider Thrust The

Propeller on engine mounting with mechanical reduction: Rider Sprint, Rider Race C, Rider

Propeller bolts draft sequence: Rider Thrust, Rider Sprint, Rider Race C.

12 6 PROP MOUNTING Mount the propeller on the motor with belt reduction: Rider Thrust The red arrow in the illustration indicates the direction of rotation of the propeller. Propeller on engine mounting with mechanical reduction: Rider Sprint, Rider Race C, Rider Jet. The red arrow in the illustration indicates the direction of rotation of the propeller. Fibreglass propeller mounting Propeller bolts draft sequence: Rider Jet Propeller bolts draft sequence: Rider Thrust, Rider Sprint, Rider Race C. Copyright by FLY PRODUCTS s.r.l. Pag. 12

7 MULTIFUNCTION HANDGRIP Manual Starter handle 1 Throttle control lever 2 STOP" button engine 3 Velcro hand tightening 8 WARRANTY WARRANTY FLY PRODUCTS provides a guarantee on materials and

13 7 MULTIFUNCTION HANDGRIP Manual Starter handle 1 Throttle control lever 2 STOP" button engine 3 Velcro hand tightening 8 WARRANTY WARRANTY FLY PRODUCTS provides a guarantee on materials and workmanship defects for a period of twelve (12) months from the date of purchase. The warranty applies only to the normal use of the product. The dealer from which you purchased the product, or FLY PRODUCTS, will repair the product at no additional charge. To obtain warranty service, please contact your local dealer (or directly FLY PRODUCTS), where to take or ship the product. The shipping expenses are always charged to the buyer. CAUTION: The warranty, even if valid, shall not apply and all costs necessary to repair will be totally borne by the buyer in the following cases: The cause of the failure is due to an improper use of the product, negligence, neglect, etc., including an engine damage due to incorrect or improper fuel regulator oil/gasoline mixture. The defect was caused by incorrect pilot operation, for example: accident, fall, or bad regulation. The malfunction is due to lacking or insufficient maintenance or changes from the pilot (example: a loose bolt falls and breaks the propeller...). The damage is caused by natural events or uncontrollable as, lightning, fires, floods, earthquakes etc. Copyright by FLY PRODUCTS s.r.l. Pag. 13

14 Copyright by FLY Products s.r.l. VERSIONE Via Perù n GROTTAMMARE (AP) - ITALY tel./fax fly@flyproducts.com Copyright by FLY PRODUCTS s.r.l. Pag. 14

IMPORTANT NOTICES 03 ASSEMBLING OF THE PARAMOTOR 05 HARNESS AND DISTANCE BARS 07 ASSEMBLING OF THE PROPELLER 10 ASSEMBLY INSPECTION 11

2 IMPORTANT NOTICES 03 ASSEMBLING OF THE PARAMOTOR 05 HARNESS AND DISTANCE BARS 07 ASSEMBLING OF THE PROPELLER 10 ASSEMBLY INSPECTION 11 TECHNICAL DATA OF THE ENGINE 12 CARBURETOR FUEL AND OIL 14 IGNITION