FOR ALL SINGLE MOTOR UNITS INSTALLATION AND OPERATING INSTRUCTIONS REV 12/15 89
|
|
- Piers Hicks
- 6 years ago
- Views:
Transcription
1 FOR ALL SINGLE MOTOR UNITS INSTALLATION AND OPERATING INSTRUCTIONS REV 12/15 89
2 INTRODUCTION Congratulations, you have just purchased one of the most unique trolling motors available today. It is the Original Engine Mounted Trolling Motor. With proper installation and care, your Navigator Trolling motor will provide you with years of trouble free use and performance. Please take a few moments to review the information contained in this booklet. The installation procedures suggested will help you successfully mount your new Navigator Trolling motor. Installation is easy particularly when you know each step ahead of time. These are the items that are included in the box: 1 Navigator Trolling Motor 1 Remote Speed Control 1 Control Module and cable 4 Bolts 4 5/16 Washers 4 5/16 Nuts 4 - #10 Screws 3 Cable Ties 1 Cable Clamp 1 Velcro/Hook Strip 1- Jumper Cable (Model only) GETTING STARTED Here is a list of the tools and supplies that you will need: 1. An Electric drill with a 5/16" and 1/8" bit 2. A ½ inch wrench for the nuts 3. A hex head allen wrench for the bolts 4. A Phillips head screwdriver 5. Two clamps to help hold the NAVIGATOR in place while marking holes for drilling ( optional ) 6. One 12 Volt deep cycle battery (Model 35 and 52 Series) Two 12 Volt deep cycle batteries (Model 55 Series)
3 !!WARNING!! BEFORE STARTING ANY INSTALLATION, DISCONNECT THE BATTERY TO THE MAIN ENGINE AND REMOVE THE KEYS FROM THE IGNITION TO PREVENT ACCIDENTAL STARTING AND POSSIBLE INJURY. MOUNTING THE MOTOR NOTE: Swim platforms may interfere with the Navigator trolling when your main motor is fully tilted upward. Check before drilling holes in your cavitation 1. Position the Navigator motor onto the anti-cavitation plate of the main engine, moving the mounting bracket as close to the main engine as possible. If needed, bend the mounting 2. Clamp the Navigator in place and carefully mark four 5/16 holes. Remove the Navigator and drill the holes through the cavitation plate. CORRECT NOT CORRECT 3. Place the Navigator over the four holes that you just drilled. Insert the four 5/16" bolts through the drilled holes of the anti- cavitation plate. Attach the washers and lock nuts. After all four bolts, washers and lock nuts are installed, tighten each lock nut securely. 4. Run the cable from the Navigator motor inside the boat though a cable port or any other available opening in the back of the boat. Be sure to leave enough slack in the motor cable in order to raise and lower the main engine. Secure the motor cable to the main engine housing with the cable clamp by using an existing bolt from the outboard or I/O, or, if an existing bolt is not available, secure the cable to the engine housing or brackets with one of the cable ties supplied. Further secure the cable to existing cables or wiring running though the boat transom by using the remaining cable ties. Make sure that there is enough slack when the outboard is in the full up AND down position.
4 PROP INSTALLATION 1. Insert drive pin into hole on motor shaft. 2. Slide prop onto motor shaft and rotate so the grove on the inside of the prop aligns with the drive pin. Push firmly so the prop slides completely onto motor shaft. 3. On Model 3500 insert cotter pin in prop nose farthest (A) from the propeller blades. For all other models, insert cotter pin in the prop nose closest (B) to the propeller blades. Note: 1. The prop must be fully seated into the drive pin in order for the cotter pin to be inserted through the hole on the nose of the prop. Note: 2. The propeller hole and cotter pin are off-centered when properly installed.
5 CONTROL MODULE INSTALLATION The state of the art control module contains all the electronics that are needed to operate your Navigator. There are no serviceable parts to the control module. 1. Mount the control module anywhere within 3ft of your deep cell battery. Make sure there is adequate air flow for the control module. The power cable from the Navigator trolling motor MUST be able to be connected to the control module. Although the control module is water resistant, it is recommended that the location you choose be as free from water as possible. 2. Mark and drill 1/8" pilot holes. 3. Fasten the control module securely with four #10 screws provided. INSTALLING REMOTE The remote is designed to be installed at or near the driver's seat. 1. Using the Velcro strip supplied, mount the remote to a handy surface. 2. After removing the cable from the controller, run the 25' cable from the control module up to the area where the remote will be located. 3. Line up the cable to the remote connector and push together. Screw securely for a watertight connection. 4. When the remote is not in use it should be placed in a protective area. This unit is not water proof, it is water resistant.
6 CONNECTING CABLES AND BATTERY NOTE: Make sure that your REMOTE is in the "OFF" Model and Series (12 Volt) 1. Plug the matching connectors together from the Navigator motor cord to the control module cables. Make sure that they are tight. 2. Connect the 3/8" red wire ring terminal from the control module to the positive battery terminal. Tighten securely. 3. Connect the 3/8" black wire ring terminal from the control module to the negative battery terminal. Tighten securely. Model Series ( 24 Volt ) 1. Connect the 3/8" red wire ring terminal from the control module to the positive battery post on battery "A". 2. Connect the 3/8" black wire ring terminal to the negative battery post on battery "B"
7 TESTING IT OUT/TIPS Now's the time to test your new Navigator trolling system to make sure everything is operating properly. Make sure objects and people are away from the props. When storing your boat for a long period of time, we recommend that the Navigator be disconnected (electrically) from your battery and the Control Module and Hand Held Remote be removed and/or stored indoors and away from any water intrusion. REMOTE FUNCTIONS All Digital Display Thrust controlled with rotary Dial Displays numeric scale which represents thrust output, 250 = max thrust Battery Check: voltage level of boat battery and Amp draw Switch from Forward to Reverse mode Push button Max Thrust Press Run to establish operating mode Power up unit or turn off TROUBLESHOOTING MOTOR WILL NOT OPERATE OR OPERATES VERY SLOWLY, Check for the following: Disconnected battery leads Discharged battery/low battery charge Corroded battery terminals Disconnected motor leads or control motor cables. Fishing line or weeds around motor shaft Corroded battery terminals Loose propeller or broken drive pin
8 SERVICE AND WARRANTY Should your unit ever require service, please do not return the product to your dealer. Please call the number below for special instructions on shipping and handling. Please call between 9:00 am - 3:00 pm (Central Standard/Daylight Time) Monday through Friday. If service is required and covered by warranty, it will be repaired or replaced as described below. If service is required and not covered by warranty (such as damage caused from improper trailering), replacement parts are available for purchase and may be paid for by credit card. The warranty coverage on this equipment is limited to the terms set forth below: MarineTech warrants this product to be free of defects in material and workmanship for a period of THREE (3) YEARS from the date of original retail purchase on the hydraulics and structural members of the plate; and ONE (1) YEAR from the date of original retail purchase on the electrical components. Positive proof of date of purchase is required for warranty service. If service is required and covered by warranty, the unit will be repaired or replaced with new or factory rebuilt parts at no charge. Call customer service for an RMA number. The defective components must be returned to the address specified, with shipping charges prepaid. Be sure to include your RMA #, your name, address, telephone number and a copy of the sales receipt showing the date of original retail purchase. All sales receipts are subject to verification. This warranty does not apply if the unit has been damaged by accident, abuse, misuse, poor installation or misapplication, or if it has been modified from its original condition, or if any serial number has been removed or defaced or altered. This warranty does not cover any expense to remove or reinstall the unit or any of its components. If a returned unit is not covered by warranty, the sender will be notified and given an estimate of the charges to repair or replace the unit, together with the return shipping charges. THIS WARRANTY DOES NOT COVER SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO DAMAGE TO OR REPLACEMENT OF OTHER EQUIPMENT AND PROPERTY. THE WARRANTY AND REMEDIES SET FORTH ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESS OR IMPLIED. DUE TO THE SPECIAL AND UNIQUE CONDITIONS THAT MAY EXIST IN EACH APPLICATION, THE MANUFACTURER SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO DEALER, AGENT OR EMPLOYEE IS AUTHORIZED TO MAKE ANY MODIFICATION, EXTENSION OR ADDITION TO THIS WARRANTY. Some states do not allow exclusion of incidental or consequential damages, so the above exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other legal rights, which may vary from state to state. FOR SERVICE send an to - info@marinetechproducts.com or call MARINETECH PRODUCTS, INC 1360 East County Road E VADNAIS HEIGHTS, MN
9 MarineTech Products, Inc. is proud to offer these fine lines: SOLUTIONS FOR MOTOR MOUNTING, REMOTE STEERING, TILT & TRIM, SHALLOW WATER ANCHORS, AND SECURITY SYSTEMS THE ORIGINAL ENGINE-MOUNTED ELECTRIC TROLLING MOTORS HIGH THRUST WITH WHISPER-QUIET EFFICIENCY ROD HOLDERS, TROLLING MOTOR SUPPORTS, AND GPS/SONAR MOUNTS AUXILIARY OUTBOARD MOTOR STEER SYSTEMS THROTTLE CONTROL FOR GAS POWERED AUXILIARY MOTORS
INSTALLATION AND OPERATING INSTRUCTIONS
DUAL AND TRITON 2 AND 3 MOTOR SERIES Model 65-0110 Freshwater Model 65-1110 Saltwater 24 volt 110 lb. Thrust Model 65-0165 Freshwater Model 65-1165 Saltwater 24 volt 165 lb. Thrust INSTALLATION AND OPERATING
More informationMODEL FIXED MOTOR BRACKET
MODEL 55-0027 FIXED MOTOR BRACKET INSTALLATION MANUAL REV 12/15 CUSTOMER MUST RECEIVE THIS MANUAL AFTER INSTALLATION INSTALLATION PROCEDURES Congratulations, you have just purchased one of the finest outboard
More informationINSTALLATION INSTRUCTIONS FOR TRANSOM ADAPTOR. FOR MOTORS UP TO 20 HP Fits Panther Brackets , , ,
INSTALLATION INSTRUCTIONS FOR 55-0023 TRANSOM ADAPTOR. FOR MOTORS UP TO 20 HP Fits Panther Brackets 55-0010, 55-0012, 55-0021, 55-0022 REV. 12/15 The TRANSOM ADAPTER allows the user to remove the outboard
More informationSWIM PLATFORM BRACKET
55-0030 SWIM PLATFORM BRACKET FOR LIGHT WEIGHT 4 STROKE ENGINES UP TO 20 HP AND 195 LBS. INSTRUCTION MANUAL REV. 12/15 4-Stroke Auxiliary Outboard Motor Bracket Mounting Instructions for Proper Location
More informationINSTALLATION AND OPERATING INSTRUCTIONS
Auxiliary Outboard Motor Bracket for the following products: 55-0010, 55-0012, 55-0020A, 55-0021, 55-0022 INSTALLATION AND OPERATING INSTRUCTIONS 55-0010 55-0012 & 55-0021 55-0020A REV. 12/15 AUXILIARY
More informationMODEL MODEL S
MODEL 55-0502 MODEL 55-0503 S INSTALLATION AND OPERATING INSTRUCTIONS CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION Rev 12/15 INTRODUCTION Congratulations, you have just purchased
More informationELECTROSTEER MODEL A FRESHWATER MODEL A SALTWATER
ELECTROSTEER MODEL 55-0100A FRESHWATER MODEL 55-0101A SALTWATER INSTALLATION AND OPERATING INSTRUCTIONS CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION Rev 01/13 P/N 99-55276 INTRODUCTION
More informationDESIGNED FOR RANGER [AND SIMILAR]
651-486-2010 info@marinetechproducts.com MODEL 35 LE 55-0350 AUXILIARY OUTBOARD MOTOR LIFT DESIGNED FOR RANGER [AND SIMILAR] FISHING BOATS This view shows the cut out on the transom plate Rev 1/16 INTRODUCTION
More informationMODEL AL ADJUSTABLE ALUMINUM BRACKET DESIGNED FOR AUXILIARY MOTORS UP TO 15HP INSTRUCTION MANUAL
MODEL 55-0407AL ADJUSTABLE ALUMINUM BRACKET DESIGNED FOR AUXILIARY MOTORS UP TO 15HP INSTRUCTION MANUAL This is the side that faces the transom Ver cal travel : 10 inches [25.4 cm] Setback up: 8 3/4 inches
More informationTrollMaster TM216 Install Manual
TrollMaster TM216 Install Manual Mercury 15 & 20 HP EFI 4-Stroke 2018 Present Tohatsu 9.9, 15 & 20 HP EFI 4-Stroke 2018 Present *This kit fits both Remote Shift & Throttle and Tiller Handle motors Read
More informationMERCURY 4, 5, & 6HP ALL YEARS NISSAN, TOHATSU 5 & 6HP 1995-PRESENT
MERCURY 4, 5, & 6HP ALL YEARS NISSAN, TOHATSU 5 & 6HP 1995-PRESENT TrollMaster is a precision throttle control designed to achieve the maximum in trolling speed accuracy. The memory feature included in
More informationJOHNSON/EVINRUDE 9.9 & 15HP SUZUKI For motors see below
JOHNSON/EVINRUDE 9.9 & 15HP 2003-2010 SUZUKI 2003-2011 For motors 2005-2011 see below TrollMaster is a precision throttle control designed to achieve the maximum in trolling speed accuracy. The memory
More informationMODEL Model 55. Model 135 CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION. Rev 3/17 PN
MODEL 55 135 Model 55 Rated for motors up to 55 horsepower and 250 lbs. Model 135 Rated for motors up to 135 horsepower and 350 lbs. CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION
More informationMODEL Model 55. Model 135 CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION. Rev 1/16 PN
MODEL 55 135 Model 55 Rated for motors up to 55 horsepower and 250 lbs. Model 135 Rated for motors up to 135 horsepower and 350 lbs. CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER INSTALLATION
More informationMODEL 35 MOTOR LIFT INSTALLATION AND OPERATING INSTRUCTIONS THIS UNIT IS SUITABLE FOR USE WITH AUXILIARY OR KICKER MOTORS UP TO 35 HP OR 150 LBS
MODEL 35 MOTOR LIFT INSTALLATION AND OPERATING INSTRUCTIONS THIS UNIT IS SUITABLE FOR USE WITH AUXILIARY OR KICKER MOTORS UP TO 35 HP OR 150 LBS CUSTOMER MUST RECEIVE THIS MANUAL AT TIME OF SALE OR AFTER
More informationRear Strut Bar Installation Guide v1.0 (Dec 2014) Part No. EC
Rear Strut Bar Installation Guide v1.0 (Dec 2014) Part No. EC0111-0303 Applications VW Mk7 Golf, GTI, Golf R Audi 8V A3, S3 List of Parts Included List of Required Tools (1) Strut Bar Rod (2) Strut Bar
More information32 lbs / 38 lbs TROLLING MOTOR
32 lbs / 38 lbs TROLLING MOTOR MODEL: 90000 / 90001 OPERATOR'S MANUAL TOLL-FREE HELPLINE: 1 866 523-5218 IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE OPERATNG YOUR NEW TM DURAMAXX TROLLING MOTOR. RETAIN
More informationBATTERY ENERGY GAUGE INSTRUCTION MANUAL
55-6100 BATTERY ENERGY GAUGE INSTRUCTION MANUAL 12/15 MODEL 55-6100 BATTERY ENERGY GAUGE Marinetech Products BATTERY ENERGY GAUGE is designed to measure the exact amount of energy stored in your battery.
More informationInstallation Instructions
85-4592 rev. 08 02-18 Installation Instructions Thank you for purchasing our sway bar kit. Please read through these instructions before installation. Auxiliary Rear Anti-Sway Bar Kit for Ford F53 part
More informationInstallation Instructions
85-3207 rev. 03 05-06 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for the Freightliner
More informationInstallation Instructions
85-3209 rev. 07 03-11 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar Kit for Workhorse W22, Holiday
More informationLight Duty Electronic Air Command
2491 PSI BAR Light Duty Electronic Air Command INSTALLATION INSTRUCTIONS Congratulations on your purchase of a Light Duty Electronic Air Command kit. This kit was designed to provide inflation control
More informationInstallation Instructions
85-4341 rev. 04 10-15 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Chevy 2500/3500/4500
More informationInstallation Instructions
85-3214 rev. 07 03-11 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit Freightliner FL Series
More informationInstallation Instructions
85-4209 rev. 05 11-18 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Factory Replacement Anti-Sway Bar Kit part #1129-135
More informationInstallation Instructions
85-5029 rev. 03 06-17 Installation Instructions Thank you for purchasing our anti-sway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Workhorse W22, Holiday
More informationInstallation Instructions
85-3414 rev. 02 11-09 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for the Monaco Diplomat
More informationInstallation Instructions
85-3910 rev. 03 01-18 Installation Instructions Thank you for purchasing the antisway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Ford F-250/F-350 part
More informationInstallation Instructions
85-3700 rev. 08 05-18 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar Kit for the F53 Chassis part
More informationHollywood Racks Sport Rider Hitch Rack Instruction Manual
Hollywood Racks Sport Rider Hitch Rack Instruction Manual Model HR1200 3 Bike, 2 rec. Model HR1210 3 Bike, 1 ¼ rec. Model HR1400-4 Bike, 2 rec. Not to be used on any trailer, fifth wheel or vehicle being
More informationJeep Wrangler (TJ)
INSTALLATION GUIDE APPLICATION MODEL YR PART # Bestop PART # Jeep Wrangler (TJ) 2003 2006 10-03315-10 751-01 INSTALLATION TIME 3:00 hrs SKILL LEVEL 1 2 3 4 4= Experienced TOOLS REQUIRED Safety goggles
More informationInstallation Instructions
85-3195 rev. 12 04-18 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Part #1139-117 Rear Anti-Sway Bar Kit 1½ diameter
More informationEndlinks Installation Guide v1.0 (Feb 2015) Part No s: EC ; EC ; EC
Endlinks Installation Guide v1.0 (Feb 2015) Part No s: EC0202-0306; EC0202-0305; EC0202-0304 Application VW Mk7 Golf, GTI, Golf R Audi 8V A3, S3 List of Parts Included List of Required Tools A. Front End
More informationModel T2642 Wall Mount. Television Wall Mount with Tilt Option
Model T2642 Wall Mount Television Wall Mount with Tilt Option Getting Started Introduction Congratulations on the purchase of your new Audio Solutions T2642 Television Wall Mount. For maximum benefit,
More informationInstallation Instructions
85-3511 rev. 04 11-15 Installation Instructions Polyurethane Bushing Kit for Ford F-53 (Front) (replaces OE bushings and brackets) part #4139-127 1-5/8 diameter INTRODUCTION Thank you for purchasing this
More informationInstallation Instructions
85-3847 rev. 01 09-09 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar TruTrac Bar Combo Kit for
More informationModel AS-FM64 Wall Mount. Full Motion Television Wall Mount
Model AS-FM64 Wall Mount Full Motion Television Wall Mount Getting Started Introduction Congratulations on the purchase of your new Audio Solutions AS-FM64 Television Wall Mount. For maximum benefit, please
More informationSUNTURA SOLAR TRACKER
WindyNation SUNTURA SOLAR TRACKER SOT-TRKS-NF User s Manual Page 1 of 10 WindyNation 08/09/2012 Table of Contents 1 Introduction... 3 1.1 Limited Warranty... 3 1.2 Restrictions... 3 1.3 Warranty Claims
More informationODY-10-1 rev. B FUEL PRESSURE GAUGE
ODY-10-1 rev. B FUEL PRESSURE GAUGE Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features
More informationPlease read BOTH these Installation Instructions and the General Information sheet prior to installing or operating this equipment.
Attachment Tab Height: 24-1/4 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Information sheet prior to installing or operating this equipment. 1. Blue Ox towing products
More informationActuLink ABS Module - ABS-MOD-400
Installation Instructions ActuLink ABS Module - ABS-MOD-400 For more information on the installation and operation of Tuson s towable ABS system, consult the installation and operations manuals for the
More informationInstallation Instructions
85-3909 rev. 01 09-09 Installation Instructions Thank you for purchasing this anti-sway bar kit. Please read through these instructions before installation. Rear Anti-Sway Bar Kit for Chevrolet G30 part
More informationModel FM2642 Wall Mount. Full Motion Television Wall Mount
Model FM2642 Wall Mount Full Motion Television Wall Mount Getting Started Introduction Congratulations on the purchase of your new Audio Solutions FM2642 Television Wall Mount. For maximum benefit, please
More informationNature s Generator Power Panel
Nature s Generator Power Panel Nature s Generator Power Panel Contents Introduction - Unpack Your Nature's Generator Power Panel - Unpack Your Solar Panel Accessory Box - Assemble Your Solar Panel Cart
More informationKit INSTALLATION GUIDE. For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
Kit 25690 MN-369 (111512) ECR 8349 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation. Failure to read these instructions
More informationDWS404 DWS524 DWS654 DWS684 DWS694. DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers
DWS404 DWS524 DWS654 DWS684 DWS694 DWS SERIES INSTALLATION/OWNER'S MANUAL Car Audio Speakers PREPARATION Safety Guidelines Thank you for purchasing the DWS Series car speakers. Although Dual has attempted
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 19-1/2 Serial Number Attachment Tab Width: 19 Please read BOTH these and the General Information
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2625 2011-15 Lincoln MKX (includes Adaptive Cruise Control) Attachment Tab Height: 18-1/4 Attachment Tab Width:
More informationUser s Manual. Complete Off-Grid Solar Kits (100 to 600 Watts) Complete Off-Grid Solar Kit Manual Revision 1.0
WindyNation Complete Off-Grid Solar Kits (100 to 600 Watts) SKU: WN-100W-KIT, WN-200W-KIT, WN-300W-KIT, WN-400W-KIT, WN-600W-KIT-12, WN-600W-KIT-24 User s Manual Page 1 of 21 WindyNation 08/09/2012 Table
More informationStainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055
USER MANUAL OUTBOARD MOTOR BRACKETS Stainless Steel Outboard Motor Brackets - Installation and Operating Instructions Models T10054 and T10055 CAUTION Do not exceed the bracket s HP or weight limits. Read
More informationFLEETWOOD TRAVEL TRAILER SLIDEOUT SYSTEM OWNER S MANUAL
FLEETWOOD TRAVEL TRAILER SLIDEOUT SYSTEM OWNER S MANUAL 82-S0150-01 REV. 1 April, 2002 TABLE OF CONTENTS PAGE # OPERATIONS MANUAL... 1 1. SYSTEM DESCRIPTION... 1 1.1 MAJOR COMPONENTS... 1 2. HOW TO OPERATE
More informationSUNTURA HD SOLAR TRACKER
WindyNation SUNTURA HD SOLAR TRACKER SOT-TRKS-NFHD User s Manual Page 1 of 11 WindyNation 08/09/2012 Table of Contents 1! Introduction... 3! 1.1! Limited Warranty... 3! 1.2! Restrictions... 3! 1.3! Warranty
More informationUNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS
UNIVERSAL CUSTOMIZABLE MUD FLAP INSTALLATION INSTRUCTIONS Thank you for purchasing ROCKSTARTM Splash Guard Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials
More informationAT-38 On-Demand. For Driving Safety and Convenience. Installation & Operation Manual for AT-38OD Unit
The Leader in Heated Washer Systems AT-38 On-Demand For Driving Safety and Convenience Installation & Operation Manual for AT-38OD Unit Our Warmest Congratulations! You are now the Owner of a Heated Washer
More informationVW/AUDI MK7 VEHICLES
Installation Manual P/N 1-301-1708-01 (STAGE 2+ FUEL KIT) P/N 1-301-1708-02 (STAGE 3+ FUEL KIT) VW/AUDI MK7 VEHICLES Warning: This installation is not recommended for a novice or the new guy in the shop.
More informationUser s Manual and Operating Instructions
User s Manual and Operating Instructions Model Numbers: CL-36-BDF-A, CL-42-BDF-A, CL-48-BDF-A E355088 READ AND SAVE THESE INSTRUCTIONS IMPORTANT: Read and understand all of the instructions in this manual
More informationAUTO-BLiP. User Manual Porsche INTELLIGENT DOWNSHIFTS. Version 1.2
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual 2005+ Porsche Version 1.2 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP while driving
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 18 Serial Number Attachment Tab Width: 18 Please read BOTH these and the General Information
More informationvan Aaken SmartBox Installation Instructions
van Aaken SmartBox Installation Instructions Vehicle: VW Golf PD Engine: 1.9 TDi 100 Bhp Year: 2004-2006 Our Website, www.vanaaken.com, has further information on all of our new products. Every effort
More informationBX Jeep Liberty Renegade 2012 Jeep Liberty Sport Installation Instructions
Attachment Tab Height: 17.5 Attachment Tab Width: 24 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and accessories
More informationInstallation Instructions
85-3180 rev. 07 03-14 Installation Instructions Thank you for purchasing this antisway bar kit. Please read through these instructions before installation. Front Anti-Sway Bar Kit for the Ford E350/450
More informationODY-04-1 or ODY-04-2 rev. B WATER TEMPERATURE GAUGE
ODY-04-1 or ODY-04-2 rev. B WATER TEMPERATURE GAUGE Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several
More informationInstallation Instructions
Installation Instructions AMP RESEARCH Power Step by Bestop Automatic Retracting Running Board Vehicle Application Nissan Titan King Cab 2004 and newer (5 ft.) Part Number: 75106-01 Nissan Titan Crew Cab
More informationInstallation and Operator s Manual
Installation and Operator s Manual Electric Utility Winch (Permanent Magnet) 2,000 lbs(907kg)-part Number 77-02000-A 2,500 lbs(1136kg)-part Number 77-02500-A General Description Each winch is equipped
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2409 2009-18 Dodge Ram 1500 Sport/ST/Laramie Limited Please read BOTH these and the General Information sheet prior
More informationODY-17-1 DIGITAL COMPASS DISPLAY
ODY-17-1 DIGITAL COMPASS DISPLAY Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features and
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX1139 2018 Jeep Wrangler / Wrangler Unlimited (JL) (All Models w/standard Bumper) Attachment Tab Height: 18 Serial
More informationHelios. 24 Light 240 Volt Controller. PRODUCT # Instruction Manual.
Helios 14 24 Light 240 Volt Controller PRODUCT # 702832 Instruction Manual www.titancontrols.net Warnings & Cautions Helios 14 Lighting Controller Overview Instructions for Operation Troubleshooting Tips
More informationInstallation Instructions. Fog Lights. The lamps get very hot when they have been in use. Do not touch them as they may cause burns.
2100X Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. Fog Lights For Installers Please give this Installation
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2265 Attachment Tab Height: 12.5 Serial Number Attachment Tab Width: 23 Please read BOTH these and the General Information
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2412 2016-18 Ram 1500 Rebel 2016-18 Ram 1500 Bighorn/Laramie/Laramie Longhorn (Chrome Bumpers) 2018 Ram 1500 (Metal
More informationI N S T A L L A T I O N G U I D E
I N S T A L L A T I O N G U I D E APPLICATION LENGTH MODEL YR PART # Ford F-250 / F-350 / F-450 Regular Cab * (48 ) 2008-2016 76234-01A Ford F-250 / F-350 / F-450 Super Cab * (60 ) 2008-2016 76234-01A
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX2414 2019 Ram 1500 (Includes Rebel) (No Classic) Attachment Tab Height: 17 Serial Number Attachment Tab Width: 38.5
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing ROLTECTM Electric Hopper Conversion. Agri-Cover, Inc. proudly manufactured this hardware using superior quality materials and workmanship. With proper
More informationSprinter Van A
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Sprinter Van 2007-2016 75163-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4= Experienced TOOLS
More informationCUSTOMER SERVICE: 800-973-8374 Frame Assembly Instructions Headboard Installation E 1. Use the remote control to raise the head of the adjustable foundation in order to gain access to the foundation
More informationCSA CERTIFIED Conforms to UL 507
Installation tion Instructions Please read and save these instructions! TURBO/MAXX12 Volt All Weather RV Ventilator Fans P/N 00-965001 Deluxe Model 1200T WITH THERMOSTAT P/N 00-965007 Standard Model 3550
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX1126 Attachment Tab Height: 14-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 16 Serial Number Attachment Tab Width: 35 Please read BOTH these and the General Information
More informationODY-19-1 AIR PRESSURE GAUGE
ODY-19-1 AIR PRESSURE GAUGE Introduction: The Odyssey gauge series from Dakota Digital, Inc. incorporates the reliability and quality of our standard gauges, along with several unique features and easy
More informationHollywood Racks Assembly & installation instructions for models:
Hollywood Racks Assembly & installation instructions for models: HR1400Y (4 bike), HR1450Y (2 bike), HR1475Y, 1450Y-E & 1455Y-E (E bikes) For use on 2 hitches only. Do not use a 1 ¼ -2 hitch adapter. Maximum
More informationFord F-150 Supercrew A (2004 Heritage) Ford F-150 Super Cab A
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Ford F-150 Supercrew 79 1999-2004 75111-01A (2004 Heritage) Ford F-150 Super Cab 72 1999-2003 75111-01A INSTALLATION TIME 3:00 hrs SKILL LEVEL 1 2
More informationEZ-R7 T-Plug. Universal 7-Pin Heavy Duty Plug For Vehicles equipped with 7-Way Trailer Connectors. Installation Instructions and Product Warranty
EZ-R7 T-Plug Universal 7-Pin Heavy Duty Plug For Vehicles equipped with 7-Way Trailer Connectors Installation Instructions and Product Warranty Professional Installation Required Thank you for purchasing
More informationElectric Pilot System Assembly, Operation, & Maintenance
Electric Pilot System Assembly, Operation, & Maintenance Congratulations on your purchase, and thank you for selecting the Electric Pilot System from Blichmann Engineering Pro Series. We are confident
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX3623 2017-19 Subaru Impreza (Manual) (No Fog Lights) Attachment Tab Height: 13 Serial Number Attachment Tab Width:
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 15-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General Information
More informationDodge SpynTec Hub Conversion Kit
SpynTec SpynTec Industries Installation Instructions for the Dodge SpynTec Hub Conversion Kit I n d u s t r i e s SpynTec Industries LLC. 11501 South Avenue North Lima, Ohio 4445 1.888.90.AXLE Page 1 Warning
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Thank you for purchasing ROXTERTM Hitch Mounted Mud Flaps. Agri-Cover, Inc. proudly manufactured these mud flaps using superior quality materials and workmanship. With proper
More informationSUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL
SUNC1200 / ITEM #40882 SUBMERSIBLE UTILITY PUMP OPERATIONS MANUAL WWW.SUNRUNNERPOOL.COM Performance Model HP GPH of Water @ Total Feet Of Lift 0 ft. 5 ft. 10 ft. 15 ft. 20 ft. 25 ft. Max. Lift SUNC1200
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX1728 2017-18 GMC Acadia (Includes Denali & All-Terrain) (No Limited) Attachment Tab Height: 16 Serial Number Attachment
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX3796 Attachment Tab Height: 13-1/2 Serial Number Attachment Tab Width: 24 Please read BOTH these and the General
More informationRaydot LLC 24 Actuator (115 VOLT)
Installation, Operation & Parts Manual Read carefully the information provided. Retain manual for future reference. Raydot LLC 24 Actuator (115 VOLT) 145 Jackson Ave. S. Cokato, MN 55321-USA (320) 286-2103
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. BX1730 Attachment Tab Height: 16 Serial Number Attachment Tab Width: 23 Please read BOTH these and the General Information
More informationAUTO-BLiP. User Manual Lotus INTELLIGENT DOWNSHIFTS. Version 1.0
AUTO-BLiP INTELLIGENT DOWNSHIFTS www.auto-blip.com User Manual Lotus Version 1.0 Copyright 2012 Tractive Technology, LLC. All rights reserved. Page 1 WARNING Use of the AUTO-BLiP while driving could lead
More informationSerial Number Purchase Date
ITEM #02708 KITCHEN FAUCET MODEL #6720-20 Français / Español p. 8 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer
More information60 PSI Boost Gauge. For Product Numbers: MT-DV01_60, MT-WDV01_60
60 PSI Boost Gauge For Product Numbers: MT-DV01_60, MT-WDV01_60 Red: 12v Constant (un-switched) Source (+) Orange: 12v Dimmer (switched) Source (+) (optional) White: 12v Ignition (switched) Source (+)
More informationDM1016S INSTALLATION/OWNER'S MANUAL 10" Marine DVC Subwoofer
DM1016S INSTALLATION/OWNER'S MANUAL 10" Marine DVC Subwoofer DM1016S INSTALLATION Preparation/Installation Please read entire manual before installation. Before You Start Disconnect negative battery terminal.
More informationAGRI-COVERTM SWITCH CONTROL INSTRUCTIONS
AGRI-COVERTM SWITCH CONTROL INSTRUCTIONS Use these instructions in place of the rocker switch and solenoid sections in your roll tarp or ROLTECTM Electric Hopper Conversion instructions. Some installs
More informationUser Guide IGD Series
US User Guide IGD Series DANGER PRIOR TO USE, READ AND UNDERSTAND PRODUCT SAFETY INFORMATION. Failure to follow the instructions may result in ELECTRICAL SHOCK, EXPLOSION, or FIRE, which may result in
More informationPlease visit for the latest version of these installation instructions.
Please visit www.blueox.com for the latest version of these installation instructions. Attachment Tab Height: 25 Serial Number Attachment Tab Width: 22-1/2 Please read BOTH these and the General Information
More information