MODEL-DB7001 Questions, problems, missing parts?

Size: px

Start display at page:

Download "MODEL-DB7001 Questions, problems, missing parts?"

Ruth Reeves
5 years ago
Views:

1 MODEL-DB7001 Questions, problems, missing parts? If you have questions or need technical support, call the Amerisun customer service department at or visit Amerisuninc.com or For engine related problems, questions and warranty service call the engine manufacturer WARNING! Read and follow all safety rules and instructions in this manual before attempting to operate this machine. Failure to comply with these instructions may result in personal injury. Save these instructions. This unit is equipped with an internal combustion engine and may spark resulting in fire or explosion if used near combustible material or fluid. Only use when the engine's exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any). The spark arrester shall be maintained in effective working order by operator.

2 TABLE OF CONTENTS Safety... 3 Safety Symbols... 6 Feature Idenfitication... 7 Box Contents... 8 Assembly Preparing Youe Snow Thrower Operation Recommended Maintenance Schedule Troubleshooting Warranty... 19

3 Safety

5 Never operate machine at high speeds on slippery surfaces. Look down and behind and use care when backing up.

7 Feature Identification TECHNICAL SPECIFICATIONS Clearing Wisth:21 inches Clearing Height:12.5 inches Engine Displacement:208cc,4stroke A B C E A- Auger Control D- Chute Handle B- Chute Assembly E- Auger C- Shave Plate - D For a complete parts breakdown go to

8 BOX CONTENTS Check to ensure all of the following items are included: a. Snow Thrower (1) b. Chute Assembly (discharge chute, chute deflector and hardware, chute rotation handle and hardware) Located in Accessory Parts Bag: a. Oil funnel (1) b. Spark Plug wrench (1) c. Operator s Manual (1) d. Registration Card (1) e. Easy set-up guide (1)

9 Oversized Gas Cap Allows for easy opening and closing for more efficient refueling. 2. Primer Bulb The Primer Bulb system is designed to enrichen the fuel mixture for starting a cold engine. DO NOT over prime the fuel system. To properly use the Primer Bulb system, depress Primer Bulb 3 times maximum when starting a cold engine. Do not use Primer Bulb system when attempting to start a warm engine. 3. Safety Key Switch The Safety key switch enables the engine electrical system and must be installed to start the engine. 4. Oversized Recoil Handle The engine is started by pulling the Recoil Handle. Always grip firmly and have your body positioned properly when pulling. When starting the engine: a. Slowly pull Recoil Handle until resistance is felt. b. Then pull firmly the full length of the rope to start engine. c. Never wrap thumb around Recoil Handle in the event of engine Kick-back. 9

10 Assembly Control Cable Attachment Auger Control Control cable Installing the Upper Handle 2. Remove 2 knobs, bolts, and washers from lower handles Insert bolts going from the middle going out, then curved washer, and knob. Tighten firmly by hand. 3

11 Chute Assembly 4. Remove bolt, washers and nuts from chute seat Place chute, and handle over discharge hole. Insert bolts from the inside through the holes, washers, then nuts. Wrench tighten.

Use the chute handle to position the direction you want to throw the snow.

12 7.Loosen the knobs on the top of the chute assembly and pivot the upper chute up or down to the desired angle. Tighten the knobs before operating the snow thrower. 8. Use the chute handle to position the direction you want to throw the snow. Note: Never lift the unit by the chute handle. 8 Chute handle Recoil Holder 9. Put recoil handle into the holder on the upper handle. 9

13 87 Use unleaded gasoline with 87 octane or. higher oil,do not overfill. Engine uses ounces of

14 1. The choke switch position as shown picture (after the machine start the choke switch should be pulled to the left to the operation state) Run Start 1 2. fig Recoil handle 4. fig.2 - (Please refer to as bellow PULL START PROCEDURE ) PULLSTART PROCEDURE

15 Engaging the Drive Lift up slightly on the handle to allow the rubber paddles on the auger to contact the pavement and propel the snow thrower forward. Pushing downward on the handle will raise the augers off the ground and stop the forward motion. Note: Excessive upward pressure on the handle will result in premature wear on the rubber auger blades and is not covered by the warranty. Engaging the Augers To engage the augers and start throwing snow, squeeze the Auger Control against the handle. Release to stop the augers. STOPPING THE ENGINE (fig.3) Pull out the red safety key to stop the engine. Keep in a safe place. Must be reinserted to start the engine. Safety key

Auger Control Cable Adjustment The auger cable is located on the left side(when standing behind the snow blower) and is made up of an upper and lower cable connected by an adjustment plate.

1 5 1 2 1- Upper Auger Cable (Always in upper center hole) 2- Adjustment Plate 3- Lower Auger Cable 4- Adjustment Plate Lower Cable Opening 5- Slip Cover 2 3 4 1.Stop the engine. 2.Disconnect the upper cable from the auger control handle.

Only move the lower cable diagonally one hole at a time from its original position. Note: The upper cable end must be in the upper single center hole of the adjustment plate.

16 Auger Control Cable Adjustment The auger cable is located on the left side(when standing behind the snow blower) and is made up of an upper and lower cable connected by an adjustment plate. The adjustment plate is located in-line with the cable below the control handle and is covered by a black plastic slip cover. The adjustment plate is used to adjust auger belt tension Upper Auger Cable (Always in upper center hole) 2- Adjustment Plate 3- Lower Auger Cable 4- Adjustment Plate Lower Cable Opening 5- Slip Cover Stop the engine. 2.Disconnect the upper cable from the auger control handle. 3. Slide up the slip cover to access the adjustment plate. 4. Adjustment is made by changing the position of the lower cable in the adjustment plate holes(1 to9). Only move the lower cable diagonally one hole at a time from its original position. Note: The upper cable end must be in the upper single center hole of the adjustment plate. Do not change the position of the upper cable. 5. Connect the upper cable to the control handle. 6. Start the engine and engage the auger to test the operation of the auger. Test the snow thrower to see if there is a noticeable difference. If after the adjustment to the control cable the auger still hesitates when rotating, the belt may need to be replaced, please call our service department for assistance. 3 U p p er C ab le L ess Ten sio n M o re Ten sio n L o w er C ab le 16

TWO YEAR WARRANTY Amerisun Inc. and LCT Engine Corporation jointly warrant this product for two years against defects in material or workmanship when used for normal residential purposes.

19 TWO YEAR WARRANTY Amerisun Inc. and LCT Engine Corporation jointly warrant this product for two years against defects in material or workmanship when used for normal residential purposes. The manufacturer will, at its option, repair or replace, for the original purchaser, any part or parts which have been found to be defective in material and workmanship. Residential use means use of the product on the same lot as your home. If you have questions or problems, or before returning this product, call toll-free or This warranty covers product defects only. Neither Amerisun nor LCT Engine Corporation is liable for indirect, incidental, or consequential damages in connection with the use of PowerSmart Products covered by this warranty, including any cost or expense of providing substitute equipment or service during reasonable periods of mal-function or non-use pending completion of repairs under this warranty. Transportation to and from the services center is the responsibility of the consumer. Some states do not allow exclusions of incidental or consequential damages, so the above exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. DISCLAIMER The information contained within this manual is the latest information as of the publication date. All contents are subject to change without notice. This manual is intended as a guide. For the latest information and procedures visit amerisuninc.com. 19 C 2015 Amerisun Inc., ITASCA, IL

Questions, problems, missing parts? If you have questions about this product or need technical support, call the Amerisun customer service department

Questions, problems, missing parts? If you have questions about this product or need technical support, call the Amerisun customer service department at 1-800-791-9458. Also contact Amerisun at Amerisuninc.com