24 ELECTRIC START SNOW THROWER MODEL

Size: px
Start display at page:

Download "24 ELECTRIC START SNOW THROWER MODEL"

Transcription

1 24 ELECTRIC START SNOW THROWER MODEL # Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious injury or death. Part # Rev C

2 For Service or Questions Call Dirty Hand Tools is a brand of 1100 W 120th Ave, Suite 600 Westminster, CO

3 Table of Contents Important Safety Information...4 Overview...7 Assembly...8 Filling with Gasoline and Oil...10 Operation Precautions...11 Operation Controls...13 Operation...14 Maintenance...16 Troubleshooting...24 Storage...27 Warranty and Specifications...Back Cover 3

4 Important Safety Information WARNING: Read and thoroughly understand all instructions and safety information before operating this Snow thrower. Failure to do so may cause serious injury or death. Do not allow anyone to operate this Snow thrower who has not read this manual. As with all power equipment, a snow thrower can be dangerous if used improperly. Do not operate this snow thrower if you have doubts or questions concerning safe operation. Call our customer service department at , , or visit if you have any questions or concerns about the safe operation of this equipment. WARNING Intended Use Do Not Use the Snow thrower for any purpose other than for which it was designed. Any other use is unauthorized and may result in serious injury or death. Personal Protective Equipment Wear ANSI-approved safety goggles, heavy-duty work boots and gloves during set up and operation. While this snow thrower operates at a relatively low noise level, about 74dB, you may want to wear ear plugs or noise deafening headphones. DANGER DANGER A SNOW THROWER IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. 4

5 Important Safety Information General Safety Failure to follow warnings, cautions, assembly and operation instructions in the Operation Manual may result in serious injury or death. DANGER READ THE OPERATION MANUAL BEFORE OPERATION. Do not permit children to operate this equipment at any time. Do not permit others that have not read and understood the complete Operation Manual to operate this equipment. Do not operate the snow thrower when under the influence of alcohol, drugs or medication. Do not allow a person who is tired or otherwise impaired or not completely alert to operate the snow thrower. DANGER NEVER place fingers, hands, or body near the snow thrower when it is running. Do not lean or reach over the snow thrower. Do not aim the discharge at a person or animal. Keep all safety guards in place and in proper working order. Keep all people (except the operator) a minimum of 25 feet from the snow thrower during operation. Do not transport the snow thrower with the engine running. Do not tilt the machine while the engine is running. Do not leave the snow thrower unattended when it is running. Turn off the engine before leaving the area. Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon monoxide, which is an odorless, tasteless, and deadly poisonous. Fill the gasoline tank outdoors with the engine off and allow the engine to cool completely. Do not operate the engine with the air cleaner or cover over the carburetor air-intake removed, except for adjustment. Removal of such parts could create a fire hazard. The muffler and engine become very hot with use and can cause a severe burn; do not touch. Allow the engine to cool before refueling, doing maintenance, or making adjustments. 5

6 Important Safety Information Safety Decals Safety labels on the snow thrower are to remind you of important information while you are operating the unit. Make sure all safety warning decals are attached and in readable condition. Replace missing or defaced decals. Contact Dirty Hand Tools at for replacement decals. DANGER AVOID INJURY FROM ROTATING AUGER KEEP HANDS, FEET AND CLOTHING AWAY DANGER 1. KEEP AWAY FROM ROTATING IMPELLER AND AUGER. CONTACT WITH IMPELLER OR AUGER CAN AMPUTATE HANDS AND FEET. 2. USE CLEAN-OUT TOOL TO UNCLOG DISCHARGE CHUTE. DO NOT USE HANDS 3. DISENGAGE CLUTCH LEVERS, STOP ENGINE, AND REMAIN BEHIND HANDLES UNTIL ALL MOVING PARTS HAVE STOPPED BEFORE UNCLOGGING OR SERVICING MACHINE. 4. TO AVOID THROWN OBJECT INJURY, NEVER DIRECT DISCHARGE AT BYSTANDERS OR ANIMALS. USE EXTRA CARE WHEN OPERATING ON GRAVEL SURFACES. 5. READ OPERATION MANUAL BEFORE USING. CLEAN-OUT TOOL DANGER STOP THE ENGINE BEFORE UNCLOGGING DISCHARGE CHUTE To prevent serious injury and fire: 1. Do not add fuel while the engine is running or when the engine is hot. 2. Do not smoke while filling with fuel. 3. Do not overfill. Use only fresh gasoline. Empty fuel before storage READ MANUAL KEEP DISTANCE DISCONNECT BEFORE WORK 6

7 Overview Your snow thrower requires some assembly. Save the packing materials and box for future use as a storage container. COMPLETELY READ AND UNDERSTAND THE OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE SNOW THROWER. AUGER CONTROL LEVER CHUTE TILT CONTROL DRIVE CONTROL LEVER SHIFT LEVER CHUTE DIRECTION CONTROL MUFFLER AUGER ADJUSTABLE SKID SHOE 7

8 Assembly Handlebar and Contol Assembly 1. Hex bolts and nylon lock nuts have been provided in a hardware package. Align the two holes at each end of the handlebar with the two holes in the handlebar support on the snow thrower. Push hex bolts through from the outside and secure with a nylon lock nut on the interior in two places on both sides of the snow thrower (see Figure 1). 2. Attach the drive wire on the left side of the snow thrower (see Figure 2). The spring mechanism should allow the wire to stretch for connection. The wire on the connection ring should slide through the attached pulley. Loosen the nut on the threaded screw with pliers to extend the spring wire. After connecting the wire rethread the screw as much as possible and tighten the nut. The wire should be taught when connected. (See Control Wire Adjustment, page 23). 3. Attach the auger wire on the right side of the snow thrower (see Figure 3). The spring mechanism should allow the wire to stretch for connection. Loosen the nut on the threaded screw with pliers and unthread slightly to extend the spring wire. After connecting the wire rethread the screw as much as possible and tighten the nut. The wire should be taught when connected. (See Control Wire Adjustment, page 23). 4. Attach the speed shift rod and secure with a r-clip that has been included in the hardware package (see Figure 3). Attaching the Chute Direction Control Cable 1. Attach the chute direction control cable to the chute direction handle by threading onto the recptacle underneath the control panel (see Figure 4). Attaching the Shift Lever Handles 1. Thread the shift lever handles on to the shift lever rods, one for the speed shift and one for the tilt control. DRIVE WIRE R-CLIP Figure 1 Figure 2 HEX BOLT & NYLON LOCK NUT (4 PLACES) CONNECTION RING CHUTE DIRECTION CONTROL HANDLE CONTROL CABLE SPEED SHIFT ROD AUGER WIRE Figure 3 Figure 4 8

9 Assembly DISCHARGE CHUTE Attaching the Discharge Chute 1. Attach the discharge chute to the snow thrower by placing it on the chute seat on the snow thrower. Position the flange keeper beneath the chute seat lip. Align the two holes in the chute and two holes in the flange keeper and secure with two bolts from the top side (see Figure 5). Repeat in three locations to attach the discharge chute to the snow thrower. 2. Attach the chute crank bracket aligning the chute notches with the spiral end of the chute directional control assembly (see Figure 6). Lubricate both ends of the chute directional control crank with petroleum jelly, paraffin wax, or light machine oil. FLANGE KEEPER CHUTE SEAT Figure 5 DISCHARGE CHUTE CHUTE DIRECTIONAL CONTROL Figure 6 Adjusting the Skid Shoes 1. Position the skid shoes based on surface conditions. Adjust upward for hard-packed snow. Adjust downward when operating on gravel or crushed rock surfaces. Loosen the two hex nuts that retain the skid shoe in place and move up or down as desired, then retighten the lock nuts (see Figure 7). Repeat for the opposite side of the snow thrower. SKID SHOE HEX NUT (2 PLACES) Figure 7 9

10 Filling with Gasoline and Oil WARNING FUEL IS HIGHLY FLAMMABLE AND POISONOUS ALWAYS FILL THE TANK WITH ENGINE OFF AND COOL. ALWAYS CHECK THE FUEL LEVEL BEFORE OPERATING. Allow the engine to cool for at least two minutes before removing the fuel cap. 1. Place the snow thrower on a level surface outdoors to fuel. 2. The fuel tank holds approximately 0.8 gallons of fuel. 87+ octane unleaded gasoline is recommended. Do not fill above the top of the fuel filter. Replace the fuel cap securely and wipe any excess from the fuel tank before starting the snow thrower. WARNING DO NOT REFUEL INDOORS OR NEAR ANY SOURCE OF POSSIBLE COMBUSTION. To prevent serious injury and fire: 1. Do not add fuel while the engine is hot or running. 2. Do not smoke while filling with fuel. 3. Do not overfill. Empty fuel before storage. WARNING GASOLINE FUEL ONLY DO NOT USE DIESEL FUEL DO NOT SMOKE WHILE FUELING. DO NOT OVERFILL. THE SNOW THROWER IS SHIPPED WITHOUT FLUIDS. YOU MUST ADD OIL BEFORE STARTING THE ENGINE Add engine oil to the upper level of the oil filler hole. SAE 10/30 motor oil is recommended for most environmental conditions. The oil capacity is 0.63 quarts (0.6L). Note: Do not thread the dipstick in when checking the oil level. 10

11 Operation Precautions DANGER COMPLETELY READ AND UNDERSTAND THIS MANUAL BEFORE ATTEMPTING TO OPERATE THE SNOW THROWER 1. Keep all safety guards in place and in proper working order at all times. 2. NEVER place fingers, hands, or body near the snow thrower when it is running. Do not lean or reach over the snow thrower when the machine is running. DANGER STOP THE ENGINE TO UNCLOG THE DISCHARGE CHUTE. NEVER USE YOUR HAND TO CLEAN OUT THE DISCHARGE CHUTE OR AUGERS. 3. Always stop the engine to dislodge snow from the discharge chute or from the augers. Wait ten seconds for the augers to stop rotating. Never use your hands to clear out the augers or discharge chute. Always use the clear-out tool provided or a similar tool. 4. Keep all people (except the operator) a minimum of 25 feet from the snow thrower during operation. 5. Always aim the discharge chute away from people and animals. 6. Do not leave the snow thrower unattended when it is running. Turn off the engine before leaving the area. 7. Do not use this piece of equipment while tired or under the influence of drugs, alcohol or medication. 8. Parts, especially exhaust system components, get very hot during use. Stay clear of hot parts. 9. Use extra caution when operating on gravel or other loose material. 11

12 Operation Precautions CAUTION DISENGAGE ALL CONTROL LEVERS AND STOP THE ENGINE BEFORE YOU LEAVE THE OPERATING POSITION. Wait until the auger/impeller comes to a complete stop before unclogging the chute assembly, making any adjustments, or inspections. 1. Exercise caution to avoid slipping or falling, especially when operating in reverse. 2. Thoroughly inspect the area where the equipment is to be used. Remove all foreign objects, which could be tripped over or thrown by the auger/impeller. 3. Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ricochet can cause serious injury to the eyes. 4. Operate the equipment with appropriate footware, gloves and clothing. Avoid loose fitting clothing that can get caught in moving parts. 5. After striking a foreign object, stop the engine, remove the wire from the spark plug, thoroughly inspect the snow thrower for any damage, and repair the damage before restarting and operating the snow thrower. 6. The auger and drive controls must be depressed to operate. Do not override this safety feature. Both control levers must operate easily and automatically return to the disengaged position when released. 7. Do not overload the snow thrower by attempting to clear snow too quickly. 8. Do not operate at high speed on icy or slippery surfaces. 9. Always be sure of your footing especially when driving in reverse. 10. If the snow thrower should vibrate abnormally, stop the engine immediately, disconnect the spark plug and inspect for damage 12

13 Operation Control AUGER CONTROL LEVER SHIFT LEVER DRIVE CONTROL LEVER CHUTE TILT CONTROL CHUTE DIRECTION CONTROL Figure 8 Shift Lever The shift lever controls the direction of travel and ground speed. There are five forward speeds. Position one (1) is the slowest and position five (5) is the fastest. There is two reverse (R) speeds. Drive Control Lever The drive control is located on the left handle. The drive control engages the transmission and propels the snow thrower forwards or backwards. Select forward or reverse and the speed before depressing the drive control. Squeeze the control grip against the handle to engage the wheel drive. Release to stop. There are five forward speeds and two reverse speeds. Release the drive control lever when changing speeds or direction. Auger Control Lever The auger control is located on the right handle. The auger control engages the rotating auger and pushes snow upwards through the discharge chute. Squeeze the control grip against the handle to engage the augers and start snow throwing. Release to stop. Chute Direction Control Rotate the discharge chute control to the direction that snow will be thrown. Chute Tilt Control The chute tilt control can be moved backwards to throw snow farther away from the machine or forwards to throw snow closer. 13

14 Operation CAUTION PRIMER BUTTON IGNITION KEY CHOKE FILL WITH OIL BEFORE STARTING Make sure the auger control and drive control are in the disengaged (released) position. Recoil Starter 1. To start a cold engine, move the choke to the CHOKE position (to the left). To restart a warm engine, leave the Choke in the RUN position (to the right). (See Figure 9). 2. Push the ignition key all the way in. Push the primer two or three times for cold engine start, making sure to cover vent hole in the center of the primer when pushing. DO NOT use primer to restart a warm engine after a short shutdown. Additional priming maybe necessary if the temperature is below 15 Fahrenheit. 3. Grip the recoil starter handle and pull slowly several times to allow the gasoline to flow into the engine s carburetor. Then pull the recoil starter handle gently until resistance is felt. Allow cable to retract fully and then pull it quickly. Repeat until the engine starts. 4. Allow the engine to run for several seconds. The engine will not develop full power until it reaches the operating temperature. Then move the choke lever slowly to its RUN position (to the right). Moving the choke lever too fast could stall the engine. Figure 9 RECOIL STARTER STARTER OUTLET Electric Starter 1. Connect extension cord to the starter outlet on the engine and into a 120V AC outlet (see Figure 10). 2. Push the ignition key all the way in. 3. Slide the choke lever to the start position. 4. Push the electric starter button and hold for no more than 10 seconds at a time, until the engine runs (see Figure 11). 5. Move the choke lever to the run position. Figure 10 ELECTRIC STARTER BUTTON Figure 11 14

15 Operation Engaging the Drive and Auger Controls 1. With the throttle control in the fast position, move shift lever into one of the five forward (F) or two reverse (R) positions. Select a speed appropriate for the snow conditions and a pace you re comfortable with. When selecting a drive speed, use slower speeds until you are familiar with the operation of the snow thrower. 2. Squeeze the auger control against the handle and the auger will turn. Release it and the augers will stop. 3. Squeeze the drive control against the handle and snow thrower will move. Release it and drive motion will stop. CAUTION Do not reposition the shift lever (change speeds or direction of travel) without first releasing the drive control and bringing the snow thrower to a complete stop. Shifting between speeds or directions while the drive control is is engaged will result in premature wear to the snow thrower s drive system. 4. Release both the auger control and the drive control to redirect the discharge chute. 5. To move from forward to reverse, release the drive control and the auger control and allow the rotating augers to stop before moving the shift lever to a new position. 6. ALWAYS release the auger and drive control and turn the engine off before dislodging snow accumulation from the augers or unclogging the discharge chute. ALWAYS use the clean-out tool provided. NEVER use your hands at any time to dislodge snow form the augers or unclog the discharge chute. 15

16 Maintenance BEFORE PERFORMING ANY MAINTENANCE PROCEDURE STOP THE ENGINE, WAIT FIVE (5) MINUTES TO ALLOW ALL PARTS TO COOL. Disconnect the spark plug wire, keeping it away from the spark plug. Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer s owner s manual for maintenance procedures. Maintenance Checklist WARNING Maintenance Before Monthly/ Every 6 Mo./ Annually/ Procedure Each Use 20 Hours 100 Hours 300 Hours Check Engine Fuel Level X X X X Check Engine Oil Level X Change Engine Oil X 1 X Check General Equipment Condition X Lubricate Gear Shaft & Auger Shaft X X X Lubricate Wheels & Discharge Chute X Check Fuel Strainer X X X Check/Clean Spark Plug X X Replace Spark Plug X Check/Adjust Idle Speed X X Check/Adjust Valve Clearance* X X Clean Fuel Tank, Strainer & Carburetor* X X Clean Combustion Chamber* Replace Fuel Lines* X X 1 After the first 20 hours of operation, every 6 months of use thereafter * Service performed by qualified technician 16

17 Maintenance WARNING TO PREVENT SERIOUS INJURY FROM ACCIDENTAL STARTING TURN THE POWER SWITCH OF THE ENGINE TO ITS OFF POSITION. Wait for the engine to cool, and remove the spark plug wire before performing any inspection, maintenance, or cleaning procedures. Spark Plug Gap ~ Figure 12 Spark Plug Maintenance: 1. Disconnect spark plug wire from end of plug. Clean out debris from around the spark plug. 2. Using the spark plug wrench provided, remove the spark plug. Inspect the spark plug. If the electrode is oily, clean it using a clean, dry rag. If the electrode has deposits on it, polish it using emery paper. If the white insulator is cracked or chipped, replace the spark plug. 3. When installing a new spark plug, adjust the plug s gap to the specification on the technical specification chart. Do not pry against the electrode or the insulator, the spark plug can be damaged (see Figure 12). 4. Install the new spark plug or the cleaned spark plug into the engine. Gasket style spark plugs should be finger-tightened until the gasket contacts the cylinder head, then turned about 1/2 to 2/3 more rotation. Non-gasket-style spark plugs should be finger-tightened until the plug contacts the head, then about 1/16 turn more. 17

18 Maintenance WARNING OIL IS VERY HOT DURING OPERATION AND CAN CAUSE BURNS. WAIT FOR ENGINE TO COOL BEFORE CHANGING OIL. Wait for the engine to cool, and remove the spark plug wire before performing any inspection, maintenance, or cleaning procedures. Changing the engine oil 1. Make sure the engine is stopped and is level. 2. Close the fuel valve. 3. Place a drain pan underneath the crankcase s drain plug. 4. Remove the drain plug and, if possible, tilt the crankcase slightly to help drain the oil out. 5. Replace the drain plug and tighten it. 6. Clean the top of the dipstick and the area around it. Remove the dipstick by threading it counterclockwise, and wipe it off with a clean lint free rag. SAE VISCOSITY GRADES 30W 10W - 30W 5W - 30W F AVERAGE OUTSIDE TEMPERATURE Note: Do not thread the dipstick in when checking the oil level. 7. Add the appropriate type of oil until the oil level is at the full level. SAE 10W-30 oil is recommended for general use for temperatures above 32 F. Use SAE 5W-30 for temperatures consistently below 32 F. 8. Thread the dipstick back in clockwise. WARNING DO NOT RUN THE ENGINE WITH TOO LITTLE OIL. THE ENGINE WILL BE PERMANENTLY DAMAGED. 18

19 Maintenance GEAR (HEX) SHAFT Figure 13 Figure 14 FRAME COVER LUBRICATION Gear Shaft The gear (hex) shaft should be lubricated at least once a season or after every 20 hours of operation. 1. Remove the lower frame cover by removing the two screws which secure it (see Figure 13). 2. Apply a light coating of an all-weather multi-purpose grease to the hex shaft (see Figure 14). Wheels At least once a season, remove both wheels. Clean and coat the axles with a multipurpose automotive grease then reinstall. Auger Shaft At least once a season, remove the shear pins on the auger shaft (see Figure 15). Spray lubricant inside shaft, around the spacers. Also lubricate the flange bearings found at either end of the shaft. Gear Case The auger gear case has been filled with grease and sealed at the factory. If disassembled from any reason, lubricate with two ounces of new grease. NOTE: Do not over fill the gear case. Damage to the seals could result. Be sure vent plug is free of grease in order to relieve pressure. Chute Directional Control Once annually, lubricate both ends of the chute directional control crank with petroleum jelly, paraffin wax, or light machine oil. SHEAR PIN SPACERS BEARING COTTER PIN Figure 15 19

20 Maintenance Shear Pin Replacement The auger is attached to the spiral shaft with shear pins secured with cotter pins. If the auger should strike a foreign object or ice jam, the snow thrower is designed to shear off those pins (see Figure 16). If the auger will not rotate, check if the pins have been sheared. When replacing shear pins, spray an oil lubricant into the shaft before inserting new pins. SHEAR PIN Shave Plate and Skid Shoes The shave plate and skid shoes on the bottom of the snow thrower are subject to wear. They should be checked periodically and replaced when necessary. To remove skid shoes: 1. Remove the four carriage bolts and hex flange nuts which secure them to the snow thrower (see Figure 17). 2. Reassemble new skid shoes with the four carriage bolts (two on each side) and hex flange nuts. To remove shave plate: 1. Remove the carriage bolts and hex nuts which attach it to the snow thrower housing (see Figure 17). 2. Reassemble new shave plate, making sure heads of carriage bolts are to the inside of housing. Tighten securely. COTTER PIN Figure 16 SKID SHOE SHAVE PLATE Figure 17 20

21 Figure 18 BELT COVER Maintenance Auger Belt Replacement 1. Remove the belt cover on the front of the engine by removing the two self-tapping screws (see Figure 18). Drain the gasoline from the snow thrower, or place a container to catch leakage from the gas cap. 2. Carefully pivot the snow thrower up and forward so that it rests on the auger housing. Remove the frame cover from the underside of the snow thrower by removing four self-tapping screws which secure it (see Figure 19). 3. Roll the auger belt off the engine pulley (see Figure 20). 4. Loosen and remove the shoulder screw which restrains the belt from jumping off of the pulley. Unhook the support bracket spring from the frame (see Figure 21). 5. Remove the belt from the auger pulley, slip the belt between the support bracket and the auger pulley (see Figure 22). 6. Attach a new auger belt and reassemble by following the instructions in reverse order. Figure 19 FRAME COVER SHOULDER SCREW SUPPORT BRACKET SPRING Figure 21 AUGER BELT AUGER BELT Figure 20 Figure 22 21

22 Maintenance Drive Belt Replacement 1. Remove the belt cover on the front of the engine by removing the two self-tapping screws (see Figure 18). Drain the gasoline from the snow thrower, or place a container to catch leakage from the gas cap. 2. Carefully pivot the snow thrower up and forward so that it rests on the auger housing. Remove the frame cover from the underside of the snow thrower by removing four selftapping screws which secure it (see Figure 19). 3. Roll the auger belt off the engine pulley (see Figure 20). 4. Loosen and remove the shoulder screw which restrains the belt from jumping off of the pulley. Unhook the support bracket spring from the frame (see Figure 21). 5. Remove the belt from the auger pulley, slip the belt between the support bracket and the auger pulley (see Figure 22). 6. See Figure 23 and follow the steps below: DRIVE BELT C A Figure 23 B AUGER BELT A B C Grasp the idler pulley and pivot it toward the right. Roll the auger belt off the engine pulley. Lift the drive belt off engine pulley. DRIVE BELT 5. Remove the belt from the drive pulley, slip the belt between the support bracket and the drive pulley (see Figure 24). 7. Attach a new drive belt, replace the auger belt and reassemble by following the instructions in reverse order. Figure 24 22

23 Maintenance THREADED SCREW CONTROL LEVER HEX NUT CONTROL WIRE SPRING CONTROL WIRE TURNBUCKLE Control Wire Adjustment When the auger or drive belts are adjusted or replaced, or after a long time of use, the control wires may need to be adjusted. The control wires for the drive control and the auger control are attached to the auger lever and the drive lever on the handlebar. There is a long threaded screw attached through the connecting spring near the base of the snow thrower. The screw threads into the control wire turnbuckle which is secured by a hex nut. Make adjustments to the wire s tension with the lever in the upwards (disengaged) position (see Figure 25). 1. To adjust the tension loosen the hex nut, unthread the hex nut to move it down the screw length one half inch or more. 2. Next rotate the turnbuckle which threads the screw into the turnbuckle until the desired tension is achieved. You can also rotate the screw with a small diameter phillips head screwdriver placed up through the bottom of the spring. 3. Then rethread the hex nut until it is tight against the housing and tighten with pliers or wrench. The control wire should be taught to operate correctly on both the auger and the drive controls. Figure 25 23

24 Engine Troubleshooting WARNING BEFORE PERFORMING ANY MAINTENANCE PROCEDURE STOP THE ENGINE, WAIT FIVE (5) MINUTES TO ALLOW ALL PARTS TO COOL. Disconnect the spark plug wire, keeping it away from the spark plug. PROBLEM The engine will not start. No fuel in tank or fuel valve closed. Choke not in start position. Low quality or deteriorated, old gasoline. Dirty fuel passageways blocking fuel flow. Carburetor needle stuck. Smell of fuel in air. Too much fuel in chamber. Spark plug wire not connected securely. Spark plug electrode wet or dirty. Incorrect spark plug gap. Spark plug wire or spark plug broken. Cylinder not lubricated after long storage. Clogged fuel filter. SOLUTION Add fuel and open fuel valve. Place choke in START position and pull recoil starter. Drain fuel. Add fresh 87+ octane unleaded gasoline. Clean out fuel passageways using fuel additive. Gently tap side of carburetor with screwdriver handle. Turn choke to RUN position. Connect spark plug wire securely to spark plug. Remove and clean spark plug. Reinstall spark plug and restart. Reset spark plug gap according to specifications. Replace spark plug and/or spark plug wire. Remove spark plug. Pour tablespoon of oil into spark plug hole. Replace spark plug. Crank engine a few times and try to start. Replace fuel filter. If the engine still will not start, visit our web site at www. dirtyhandtools.com or call for assistance. Engine misfires, backfires or knocks. Spark plug wire loose. Tighten spark plug wire. Incorrect spark plug gap. Reset spark plug gap according to specifications (see page 17). Spark plug wire or spark plug broken. Replace spark plug and/or spark plug wire. Low quality or deteriorated, old gasoline. Drain fuel. Add new fresh 87+ octane unleaded gasoline. Engine too cold. Use cold weather fuel and oil additives. Engine knocks. Engine overloaded, do not exceed recommended load rating. Engine stops suddenly. Low quality or deteriorated, old gasoline. Defective fuel cap creates vacuum. Improper idle speed. Incorrect timing, deposit buildup, worn engine or other mechanical problem. Drain fuel. Add fresh 87+ octane unleaded gasoline. Test and replace fuel cap. Move choke to RUN position. Requires qualified technician. 24

25 Snow Thrower Troubleshooting PROBLEM No snow through thrower s discharge chute. Discharge chute and/or auger is clogged SOLUTION Disengage the auger and drive controls, stop the engine, wait ten seconds for the auger to stop rotating, then using the clean-out tool provided, remove the snow clogging the chute. Auger is not rotating Shear pin(s) are missing or broken and need to be replaced. Snow not completely removed from surface Skid shoe needs adjustment Disengage the auger and drive controls, stop the engine, wait ten seconds for the auger to stop rotating. Loosen the two hex nuts on the skid show on either side of the snow thrower. Raise the skid shoes so the entire bottom surface of the skid show rests on the ground evenly. Retighten the hex nuts on both sides. This adjustment allows the auger to come into closer contact with the ground surface. Snow not evenly removed from surface Tires not inflated evenly Check tire pressure, inflate both tires to the same pressure recommended (15-20 psi) so auger is level on the ground. Skid shoes not correctly adjusted Make sure that skid shoes are at same height. Cannot adjust the discharge chute Moving parts are frozen In extreme cold environments some controls and moving parts may freeze. Do not use excessive force to operate frozen controls. Allow the engine to run for several minutes to warm up and thaw frozen parts. Snow thrower continually clogs Machine does not propel itself forward Operate at a slower pace to allow the snow thrower to dispel snow through the discharge chute. Forcing the snow thrower to move faster than it can remove the snow will result in clogged auger and/or discharge chute. Do not overload the thrower in extremely heavy or wet snow. 25

26 Snow Thrower Troubleshooting PROBLEM Auger does not engage. Auger control wire is too loose. SOLUTION If there is too much slack in the auger control wire, the augers will not be engaged properly. Turn off the engine. Adjust the tension of the auger control wire (see page 23). Auger is not rotating. Shear pin(s) are missing or broken and need to be replaced. Auger belt is off the pulley, broken or worn. Turn off the engine and allow to cool down for several minutes. Put the auger belt back on the pulley or replace the belt as needed. (See page 21). Snow thrower does not propel itself. Drive control does not engage. Drive control wire is too loose. If there is too much slack in the drive control wire, the drive will not be engaged properly. Turn off the engine. Adjust the the tension of the drive control wire (see page 23). Drive belt is off the pulley, broken or worn. Turn off the engine and allow to cool down for several minutes. Put the drive belt back on the pulley or replace the belt as needed. (See page 22). Friction wheel is worn. Refer to a qualified service technician for friction wheel replacement. Snow thrower vibrates excessively. Damaged auger or loose parts. Turn off the engine and allow to cool down for several minutes. Disconnect the spark plug wire. Examine the auger, replace shear pins if missing or broken, tighten all connecting bolts. If excessive vibration continues have the snow thrower serviced by a qualified technician. 26

27 Storage DO NOT STORE SNOW THROWER WITH FUEL IN TANK INDOORS Do not store in poorly ventilated areas, or near furnace, water heater, clothes dryer or gas appliance. WARNING CYLINDER ASSEMBLY 1. For short term storage wait for the engine to cool, then clean the engine with a clean cloth. 2. When the snow thrower is to be stored for longer than 30 days, prepare the engine for storage by emptying the fuel tank and draining all fuel lines. Note: As an alternative to draining the fuel system, a fuel stabilizer can be added to a full gas tank. Do not drain the carburetor if using a fuel stabilizer. Figure 26 DRAIN PLUG 3. Run the engine until all the fuel has been consumed and the engine stops. 4. Drain the carburetor (see Figure 26). Remove the 6 hex bolts on the muffler, and slide the mufffler cover off of the engine to access the carburetor. 5. Clean out area around spark plug and remove. Pour one tablespoon of engine oil into the cylinder through the spark plug hole. Reinstall the spark plug, but leave the spark plug wire disconnected. Pull recoil starter handle to distribute oil in the cylinder. Stop after one or two revolutions when you feel the piston start the compression stroke (when you start to feel resistance). 6. Apply a thin coat of rust preventive oil to all uncoated metal parts. 7. Cover and store in a dry, well-ventilated area out of reach of children. 27

28 Warranty & Specifications IMPORTANT NOTICE We, the manufacturer, reserve the right to change the product and/ or specifications in this manual without notification. The manual is for information usage only and the pictures and drawings depicted herein are for reference only. Warranty Repair and Service Do not return this product to the store for warranty issues or repair. Call our customer service department at , , or visit for the location of the nearest service center. Record the information below for future reference. Model No. Serial No. Date of Purchase Place of Purchase Specifications SKU/Part No Description 24 Dual Stage Snow Thrower Operating Width 24 Operating Height 20 Transmission 5 Speeds Forward, 2 Speeds Reverse Engine 212CC* DHT EPA/CARB Approved Fuel Type Unleaded Gasoline, 87+ Octane Fuel Capacity 0.95 Gallon (3.6 Liters) Oil Capacity 1.27 Pints (0.6 Liters) Starting System 110V Electric/Recoil Back-up Chute Rotation Hand crank, 190 Turning Radius Max. Throwing Distance 36 Feet Dimensions 50 L x 24 W x 39 H Weight 128 Lbs. Shipping Weight 148 Lbs. Accessories Clean-Out Tool, Shear Pins Warranty 2 Year Limited Warranty *As rated by engine manufacturer Dirty Hand Tools is a brand of 1100 W 120th Ave., Suite 600 Westminster, CO For Service or Questions Call

Operation Manual 21 SNOW BLOWER MODEL #

Operation Manual 21 SNOW BLOWER MODEL # 21 SNOW BLOWER MODEL # 101487 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious injury

More information

30 SNOW BLOWERS MODELS

30 SNOW BLOWERS MODELS 30 SNOW BLOWERS MODELS # 103879 & 103880 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in

More information

1-1/2 DIAMETER WATER PUMP

1-1/2 DIAMETER WATER PUMP 1-1/2 DIAMETER WATER PUMP 2.2HP/79.8cc Engine MODEL # 101099 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information

More information

Operation Manual. 21 Inch Self-Propelled Lawn Mower MODEL #

Operation Manual. 21 Inch Self-Propelled Lawn Mower MODEL # 21 Inch Self-Propelled Lawn Mower MODEL # 106461 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result

More information

PORTABLE INVERTER GENERATOR MODEL

PORTABLE INVERTER GENERATOR MODEL 3200Watts PORTABLE INVERTER GENERATOR MODEL #104612 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may

More information

Operation Manual. 196cc HP GASOLINE ENGINE. Model #

Operation Manual. 196cc HP GASOLINE ENGINE. Model # 196cc HP GASOLINE ENGINE Model # 100372 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in

More information

950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS. MODELS #104609, # and #

950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS. MODELS #104609, # and # 950 Watts (104609) /1200Watts (104610) /2000Watts (104611) PORTABLE INVERTER GENERATORS MODELS #104609, #104610 and #104611 Operation Manual This safety alert symbol identifies important safety messages

More information

Operation Manual. 10 Mini-Cultivator MODEL #

Operation Manual. 10 Mini-Cultivator MODEL # 10 Mini-Cultivator MODEL # 103350 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious

More information

1000 RATED WATTS/1200 MAXIMUM WATTS PORTABLE POWER GENERATOR

1000 RATED WATTS/1200 MAXIMUM WATTS PORTABLE POWER GENERATOR 1000 RATED WATTS/1200 MAXIMUM WATTS PORTABLE POWER GENERATOR 1200 W P OW E R G E N E R ATO R MODEL # 101174 Operation Manual This safety alert symbol identifies important safety messages in this manual.

More information

7000 RATED WATTS/8750 MAXIMUM WATTS PORTABLE POWER GENERATOR

7000 RATED WATTS/8750 MAXIMUM WATTS PORTABLE POWER GENERATOR 30A 7000 RATED WATTS/8750 MAXIMUM WATTS PORTABLE POWER GENERATOR 8 7 5 0 W P O W E R G E N E R AT O R START MODEL # 101175 Operation Manual This safety alert symbol identifies important safety messages

More information

Operation Manual. All Terrain Power Cart MODEL #

Operation Manual. All Terrain Power Cart MODEL # All Terrain Power Cart MODEL # 101872 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious

More information

800 RATED WATTS/900 MAXIMUM WATTS PORTABLE POWER GENERATOR

800 RATED WATTS/900 MAXIMUM WATTS PORTABLE POWER GENERATOR 800 RATED WATTS/900 MAXIMUM WATTS PORTABLE POWER GENERATOR 900W POWER GENERATOR MODEL # 101172 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to

More information

Operation Manual. 3200psi Pressure Washer 7HP/206cc Engine MODEL #

Operation Manual. 3200psi Pressure Washer 7HP/206cc Engine MODEL # 3200psi Pressure Washer 7HP/206cc Engine MODEL # 101089 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information

More information

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual

Wheel Horse. 44 Snowthrower. for 5xi Lawn and Garden Tractors. Model No & Up. Operator s Manual FORM NO. 8 Rev A Wheel Horse Snowthrower for 5xi Lawn and Garden Tractors Model No. 7966 890050 & Up Operator s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information

More information

Operator s Manual. Model 6FE Shown

Operator s Manual. Model 6FE Shown Operator s Manual Two-Stage Snow Thrower Styles E & F Model 6FE Shown IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should

More information

Post Hole Diggers Compact Standard Heavy Duty

Post Hole Diggers Compact Standard Heavy Duty Post Hole Diggers Compact Standard Heavy Duty MODEL 90 / MODEL 100 / MODEL 110 # 100623 # 100498 # 100624 Operation Manual This safety alert symbol identifies important safety messages in this manual.

More information

Table of Contents. Safety symbols... 3 Assembly 6. Operation Maintenance Troubleshooting 11. Storage. 12. Notes. 13

Table of Contents. Safety symbols... 3 Assembly 6. Operation Maintenance Troubleshooting 11. Storage. 12. Notes. 13 Table of Contents Safety symbols... 3 Assembly 6 Operation... 8 Maintenance... 10 Troubleshooting 11 Storage. 12 Notes. 13 2 Safety Information Attention; this machine can be dangerous! All operators should

More information

LAWN MOWER OWNER S MANUAL

LAWN MOWER OWNER S MANUAL LAWN MOWER OWNER S MANUAL Woodies SKU: 1153279 & 1153280 CAUTION: Read and follow all Safety Rules and Instructions before operating this equipment Thank you for choosing our Gasoline Lawnmower. 1 To ensure

More information

KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.

KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. KING CANADA 950W PORTABLE GENERATOR MODEL: KCG-951G INSTRUCTION MANUAL COPYRIGHT 2011 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. WARRANTY & SERVICE INFORMATION 1-YEAR LIMITED WARRANTY FOR THIS 950W

More information

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Form No. 9 66 in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Part No. 06 88 Installation Instructions English (EN) This kit is for installing an existing 00 Series Classic

More information

622 Power Throw Snowthrower

622 Power Throw Snowthrower FORM NO. 687 6 Power Throw Snowthrower Model No. 806 990000 & Up Operator s Manual WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth

More information

Operation Manual. 60 Zero-Turn Mower MODELS # & #

Operation Manual. 60 Zero-Turn Mower MODELS # & # 60 Zero-Turn Mower MODELS # 103408 & # 104368 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result

More information

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Two Stage Snow Thrower Models 930 SWE & 933 SWE

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Two Stage Snow Thrower Models 930 SWE & 933 SWE Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Operator s Manual Two Stage Snow Thrower Models 930 SWE & 933 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS

More information

Operation Manual POWER POST DRIVER MODELS # &

Operation Manual POWER POST DRIVER MODELS # & I POWER POST DRIVER O MODELS # 103400 & 104369 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result

More information

Operation Manual. 46 Rough Cut Brush Mower MODEL #

Operation Manual. 46 Rough Cut Brush Mower MODEL # 46 Rough Cut Brush Mower MODEL # 106717 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in

More information

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Operator s Manual Two Stage Snow Thrower Model 945 SWE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN

More information

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor

42in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Form No. 5 70 in GT Classic Single Stage Snowthrower Conversion Kit XT Series Garden Tractor Part No. 06 858 Installation Instructions Original Instructions (EN) This kit is for installing an existing

More information

OPERATOR S MANUAL IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

OPERATOR S MANUAL IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY OPERATOR S MANUAL SNOW THROWER MODEL E740F IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY Warning: This unit is equipped with an internal combustion engine and should not be used on or near any

More information

Earth Auger MAG500 MAG500RS

Earth Auger MAG500 MAG500RS Earth Auger MAG500 MAG500RS US Owner s/operator s Manual Completely read and understand this manual before using this product. - 0 - Foreword This Owner s/ Operator s Manual is designed to familiarize

More information

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. Single-Stage (200 Series)

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. Single-Stage (200 Series) Safe Operation Practices Set-Up Operation Service Troubleshooting Operator s Manual Snow Thrower Single-Stage (200 Series) Table of Contents Safe Operation Practices... 2 Assembly & Set-Up... 5 Controls

More information

Owner s/operator s Manual

Owner s/operator s Manual Water Pump MP2533E2 Owner s/operator s Manual Completely read and understand this manual before using this product. Foreword This Owner s/ Operator s Manual is designed to familiarize the operator with

More information

Post Hole Digger. Operation Manual MODEL

Post Hole Digger. Operation Manual MODEL Post Hole Digger MODEL 107798 Operation Manual This safety alert symbol identifies important safety messages in this manual. Failure to follow this important safety information may result in serious injury

More information

Introduction. Power Clear 721 Snowthrower Model No Serial No and Up Model No Serial No and Up.

Introduction. Power Clear 721 Snowthrower Model No Serial No and Up Model No Serial No and Up. Power Clear 721 Snowthrower Model No. 38741 Serial No. 402082000 and Up Model No. 38742 Serial No. 402082000 and Up Form No. 3415-621 Rev B Operator's Manual Introduction This machine is intended to be

More information

824 and 1028 Power Shift Snowthrowers

824 and 1028 Power Shift Snowthrowers FORM NO. 332 378 824 and 028 Power Shift Snowthrowers Model No. 38542 990000 & Up Model No. 38558 990000 & Up Operator s Manual WARNING: The engine exhaust from this product contains chemicals known to

More information

Operating and Assembly Manual

Operating and Assembly Manual Model 1080 Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 08-02-16 SAFETY RULES Remember, any power equipment can cause injury if operated

More information

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5

Light Shipping Location. Remove nut to detach headlight from under dash. Keep nut to mount light on unit. Figure 5 Install Headlight (900, 0, 05) (Figure 5). Remove headlight from location under dash panel. Keep nut for installation.. Attach headlight to bolt on right side of the dash. Fasten with nut removed in step..

More information

Trench Filler for Compact Utility Loaders

Trench Filler for Compact Utility Loaders Form No. 3353-608 Rev A Trench Filler for Compact Utility Loaders Model No. 22472 260000001 and Up Operator s Manual Register your product at www.toro.com Original Instructions (EN) Contents Page Introduction................................

More information

Operator's Manual. WS2690BSE Snow thrower. Safety Setup Instructions Product Overview Controls Operation Maintenance Storage Troubleshooting

Operator's Manual. WS2690BSE Snow thrower. Safety Setup Instructions Product Overview Controls Operation Maintenance Storage Troubleshooting Operator's Manual R WS2690BSE Snow thrower Safety Setup Instructions Product Overview Controls Operation Maintenance Storage Troubleshooting Worldlawn Power Equipment, Inc. Industrial Park 2415 Ashland

More information

1100W PORTABLE GENERATOR

1100W PORTABLE GENERATOR 1100W PORTABLE GENERATOR MODEL NO: G1200 PART NO: 8010110 OPERATION & MAINTENANCE INSTRUCTIONS LS0312 INTRODUCTION Thank you for purchasing this CLARKE 1100W Portable Generator. Before attempting to use

More information

Gasoline Inverter Generator

Gasoline Inverter Generator user manual Gasoline Inverter Generator table of contents Preface Introduction... Safety Information Exhaust fumes are poisonous... Fuel is highly flammable and poisonous... Engine and muffler may be hot...

More information

TWO STAGE GAS SNOW THROWER

TWO STAGE GAS SNOW THROWER TWO STAGE GAS SNOW THROWER MODEL DB703-24 and 26 Questions, problems, missing parts? If you have questions or need technical support, call the Amerisun customer service department at -800-79-9458 or visit

More information

5500 RATED WATTS/6500 MAXIMUM WATTS PORTABLE POWER GENERATOR

5500 RATED WATTS/6500 MAXIMUM WATTS PORTABLE POWER GENERATOR 25A 5500 RATED WATTS/6500 MAXIMUM WATTS PORTABLE POWER GENERATOR 6 5 0 0 W P O W E R G E N E R AT O R 25A MODELS #101092 and #104502 Operation Manual This safety alert symbol identifies important safety

More information

Model 858-RH. Operating and Assembly Manual. Palmor Products Inc Serum Plant Road Thorntown, IN 46071

Model 858-RH. Operating and Assembly Manual. Palmor Products Inc Serum Plant Road Thorntown, IN 46071 Model 5-RH Operating and Assembly Manual Palmor Products Inc. 55 Serum Plant Road Thorntown, IN 6071 3/31/015 SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the

More information

Single and Double Head Powered Screed. Screed King. User Manual. SCR-UM EN-04 (December 2018)

Single and Double Head Powered Screed. Screed King. User Manual. SCR-UM EN-04 (December 2018) Single and Double Head Powered Screed Screed King SCR-UM-00364-EN-04 () User Manual Single and Double Head Powered Screed, Screed King CONTENTS Scope of This Manual.............................................

More information

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (600 and 500 Series)

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (600 and 500 Series) Safe Operation Practices Set-Up Operation Service Troubleshooting Operator s Manual Snow Thrower 2-Stage and 3-Stage (600 and 500 Series) Table of Contents Safe Operation Practices... 2 Assembly & Set-Up...

More information

522, 622, and 724 Snowthrower

522, 622, and 724 Snowthrower Form No. 3322-80 Rev A 522, 622, and 724 Snowthrower Model No. 3805 20000000 and Up Model No. 38064 20000000 and Up Model No. 38072 20000000 and Up Operator s Manual Pour obtenir gratuitement une version

More information

TWO STAGE GAS SNOW THROWER

TWO STAGE GAS SNOW THROWER TWO STAGE GAS SNOW THROWER MODEL DB7659-22 and 24 Questions, problems, missing parts? If you have questions or need technical support, call the Amerisun customer service department at 1-800-791-9458 or

More information

Sno-Thro. Compact Series. Operator s Manual Manuel du Utilisateur. Models Classic 24 (SN ) Compact 20 (SN )

Sno-Thro. Compact Series. Operator s Manual Manuel du Utilisateur. Models Classic 24 (SN ) Compact 20 (SN ) Operator s Manual Manuel du Utilisateur Compact Series Models 920025 Classic 24 (SN 000101 004999) 920026 Compact 20 (SN 000101 +) 920027 Compact 24 (SN 000101 +) 920028 Compact 24 Track (SN 000101 +)

More information

Introduction. Operator's Manual

Introduction. Operator's Manual Form No. 3373-560 Rev A Power Max Heavy Duty 928 OE and 926/1028 OXE Snowthrower Model No. 38660 Serial No. 313000001 and Up Model No. 38664 Serial No. 313000001 and Up Model No. 38674 Serial No. 313000001

More information

INSTRUCTION MANUAL. 24 inch Two Stage Gas Snow Thrower. Model # DB7279

INSTRUCTION MANUAL. 24 inch Two Stage Gas Snow Thrower. Model # DB7279 INSTRUCTION MANUAL 24 inch Two Stage Gas Snow Thrower Model # DB7279 Have product questions or need technical support? Please feel free to contact us! Website: www.amerisuninc.com www.powersmartusa.com

More information

AND OPERATING INSTRUCTIONS IMPORTANT:

AND OPERATING INSTRUCTIONS IMPORTANT: WOOD CHIPPER User Manual FM6.5WC SAFETY AND OPERATING INSTRUCTIONS IMPORTANT: Read safety rules and instructions carefully before operating equipment. Table of Contents Table of Contents PART I: General

More information

824 XL Power Throw Snowthrower

824 XL Power Throw Snowthrower Form No. 3327-976 824 XL Power Throw Snowthrower Model No. 38066 230000001 and Up Operator s Manual International English (GB) This spark ignition system complies with Canadian ICES-002. Ce système d allumage

More information

TWO STAGE GAS SNOW THROWER

TWO STAGE GAS SNOW THROWER TWO STAGE GAS SNOW THROWER MODEL DB7651-24, 26 and 28 Questions, problems, missing parts? If you have questions or need technical support, call the Amerisun customer service department at 1-800-791-9458

More information

Table of Contents. Safety Assembly Pre-operation / Starting. 7. Operation.. 8. Maintenance. 9. Storage 10

Table of Contents. Safety Assembly Pre-operation / Starting. 7. Operation.. 8. Maintenance. 9. Storage 10 Table of Contents Safety... 3 Assembly... 6 Pre-operation / Starting. 7 Operation.. 8 Maintenance. 9 Storage 10 Parts drawings..11 Parts list by number..12 Notes.13 2 Safety Information Attention; this

More information

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Two-Stage Snow Thrower 500 Series & 600 Series

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Two-Stage Snow Thrower 500 Series & 600 Series Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Operator s Manual Two-Stage Snow Thrower 500 Series & 600 Series WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS

More information

824 Power Shift Snowthrower

824 Power Shift Snowthrower Form No. 337-980 84 Power Shift Snowthrower Model No. 38543 3000000 and Up Operator s Manual International English (GB) This spark ignition system complies with Canadian ICES-00. Ce système d allumage

More information

Operating and Assembly Manual

Operating and Assembly Manual Model 470-/H/PRO/IC Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 11-11-11 SAFETY RULES Remember, any power equipment can cause injury if

More information

NOTES FOR SAFETY OPERATOR-ONLY.

NOTES FOR SAFETY OPERATOR-ONLY. NOTES FOR SAFETY Both the parents and their child must fully understand everything in this manual before riding. This vehicle is for OPERATOR-ONLY. This vehicle is only designed for operation on level,

More information

ITEM # V SNOW SHOVEL. MODEL #KSS 2540A-06 Español p. 18. ATTACH YOUR RECEIPT HERE Serial Number. Purchase Date

ITEM # V SNOW SHOVEL. MODEL #KSS 2540A-06 Español p. 18. ATTACH YOUR RECEIPT HERE Serial Number. Purchase Date ITEM #0727249 40 V SNOW SHOVEL MODEL #KSS 2540A-06 Español p. 18 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer

More information

MODEL 565CKG Operating and Assembly Manual Midwest Equipment Manufacturing, Inc Serum Plant Road Thorntown, IN 46071

MODEL 565CKG Operating and Assembly Manual Midwest Equipment Manufacturing, Inc Serum Plant Road Thorntown, IN 46071 MODEL 565CKG Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 11-20-14 SAFETY RULES Remember, any power equipment can cause injury if operated

More information

924, 1028, and 1332 Power Shift Snowthrower

924, 1028, and 1332 Power Shift Snowthrower Form No. 3326-376 Rev A 924, 028, and 332 Power Shift Snowthrower Model No. 38547 22000000 and Up Model No. 38560 22000000 and Up Model No. 38592 22000000 and Up Operator s Manual Domestic English (EN)

More information

OWNERS MANUAL. Model No. LST42G 42" SNOW THROWER. Safety Assembly Operation Maintenance Parts

OWNERS MANUAL. Model No. LST42G 42 SNOW THROWER. Safety Assembly Operation Maintenance Parts OWNERS MANUAL Model No. LST42G 42" SNOW THROWER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com

More information

Power Clear 621 R Snowthrower. Model No Serial No and Up Model No Serial No and Up Operator's Manual. Model No.

Power Clear 621 R Snowthrower. Model No Serial No and Up Model No Serial No and Up Operator's Manual. Model No. Power Clear 621 R Snowthrower Form No. 3369-491 Rev B Model No. 38451 Serial No. 312000001 and Up Model No. 38452 Serial No. 312000001 and Up Operator's Manual Introduction This machine is intended to

More information

Single-Stage Snow thrower

Single-Stage Snow thrower Save This Manual for Future Reference Single-Stage Snow thrower Operator s Manual MODEL NUMBER YB4628 SERIAL NUMBER PURCHASE DATE Both model number and serial number may be found on the main label. You

More information

Introduction. Safety. 1028LE Power Max Snowthrower. Warning. Operator s Manual. Form No Rev A. Model No Serial No.

Introduction. Safety. 1028LE Power Max Snowthrower. Warning. Operator s Manual. Form No Rev A. Model No Serial No. 1028LE Power Max Snowthrower Form No. Introduction Model No. 38642 Serial No. 240000001 and Up Read this manual carefully to learn how to operate and maintain your product properly and to avoid injury

More information

Introduction. Power Max Snowthrowers. Warning. Operator's Manual

Introduction. Power Max Snowthrowers. Warning. Operator's Manual Power Max Snowthrowers Form No. 3362-558 Rev A Model No. 38624 Serial No. 310000001 and Up Model No. 38634 Serial No. 310000001 and Up Model No. 38644 Serial No. 310000001 and Up Model No. 38654 Serial

More information

824 XL Power Throw Snowthrower

824 XL Power Throw Snowthrower Form No. 3326-374 Rev A 824 XL Power Throw Snowthrower Model No. 38086 220000001 and Up Operator s Manual Domestic English (EN) Warning The engine exhaust from this product contains chemicals known to

More information

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Track Drive Snow Thrower 726 TDE

Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty. Track Drive Snow Thrower 726 TDE Safe Operation Practices Set-Up Operation Maintenance Service Troubleshooting Warranty Operator s Manual Track Drive Snow Thrower 726 TDE WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS

More information

CUB CADET CORP. P.O. BOX CLEVELAND, OHIO

CUB CADET CORP. P.O. BOX CLEVELAND, OHIO Operator s Manual Single Stage Snow Thrower Model 421R IMPORTANT: Read safety rules and instructions carefully Warning: This unit is equipped with an internal combustion engine and should not be used on

More information

Sno-Thro. Platinum Series Models. Service Guide

Sno-Thro. Platinum Series Models. Service Guide Sno-Thro Platinum Series Models 908 Platinum SHO (SN 00000 +) 909 Platinum 8 SHO Track (SN 0000 +) 900 Platinum 0 SHO (SN 00000 +) Service Guide E0 ENGLISH 085600 8/5 TABLE OF CONTENTS SAFETY.............................

More information

Craftsman Snow Thrower Model PARTS LIST

Craftsman Snow Thrower Model PARTS LIST Craftsman Snow Thrower Model 24.88955 11 13 3 26 24 9 1 18 54 6 25 15 20 23 16 5 14 1 55 9 4 4 28 8 30 2 5 56 35 36 46 3 39 50 53 43 38 48 52 42 51 41 40 49 4 44 31 45 31 21 29 34 9 19 10 32 22 26 Craftsman

More information

Introduction. Safety. CCR 2450 GTS Snowthrower. Warning. Operator's Manual

Introduction. Safety. CCR 2450 GTS Snowthrower. Warning. Operator's Manual CCR 2450 GTS Snowthrower Form No. 3360-738 Rev A Model No. 38515 Serial No. 290000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product

More information

3. INSPECTION/ADJUSTMENT

3. INSPECTION/ADJUSTMENT 3 3 INSPECTION/ADJUSTMENT SERVICE INFORMATION -------------------------------------------- 3-1 MAINTENANCE SCHEDULE ---------------------------------------- 3-2 FUEL LINE/FUEL FILTER -------------------------------------------

More information

INSPECTION/ADJUSTMENT

INSPECTION/ADJUSTMENT 3 3 INSPECTION/ADJUSTMENT SERVICE INFORMATION----------------------------------------------------------------------- 3-1 MAINTENANCE SCHEDULE-------------------------------------------------------------------

More information

OWNER S / OPERATOR S MANUAL

OWNER S / OPERATOR S MANUAL OWNER S / OPERATOR S MANUAL SAFETY PAGE 1 RECOGNIZE SAFETY INFORMATION This is the safety-alert symbol. When you see this symbol in this manual or on your EdgeMasterTM, be alert to the potential for personal

More information

1028 Power Shift Snowthrower

1028 Power Shift Snowthrower FORM NO. 339 49 08 Power Shift Snowthrower Model No. 38556 890000 & Up Operator s Manual WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer,

More information

Sno-Thro. Compact Series. Operator s Manual Manuel du Utilisateur. Models Classic 24 (SN ) Compact 20 (SN )

Sno-Thro. Compact Series. Operator s Manual Manuel du Utilisateur. Models Classic 24 (SN ) Compact 20 (SN ) Operator s Manual Manuel du Utilisateur Compact Series Models 920025 Classic 24 (SN 000101 +) 920026 Compact 20 (SN 000101 +) 920027 Compact 24 (SN 000101 +) 920028 Compact 24 Track (SN 000101 +) Sno-Thro

More information

1232 Power Shift Snowthrower

1232 Power Shift Snowthrower FORM NO. 9 40 Power Shift Snowthrower Model No. 8590 890000 & Up Operator s Manual WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth

More information

Model 452-DIC/DH. Operating and Assembly Manual

Model 452-DIC/DH. Operating and Assembly Manual . Model 452-DIC/DH Operating and Assembly Manual Palmor Products Inc. 5225 Serum Plant Road Thorntown, IN 46071 02-14-12 SAFETY RULES Remember, any power equipment can cause injury if operated improperly

More information

22" 2-STAGE SNOWBLOWER

22 2-STAGE SNOWBLOWER model number 060-373-6 Contact us: -844-48-777 " -STAGE SNOWBLOWER IMPORTANT: Please read this manual carefully before running this snowblower and save it for reference. INSTRUCTION MANUAL model no. 060-373-6

More information

Operating and Assembly Manual

Operating and Assembly Manual Model 455-IC/PRO/H Operating and Assembly Manual Midwest Equipment Manufacturing, Inc. 5225 Serum Plant Road Thorntown, IN 46071 03-08-12 SAFETY RULES Remember, any power equipment can cause injury if

More information

Operator s Manual. IMPORTANT: Read safety rules and instructions carefully before operating equipment.

Operator s Manual. IMPORTANT: Read safety rules and instructions carefully before operating equipment. Operator s Manual Single Stage Snow Thrower Model Series 140 through E173 IMPORTANT: Read safety rules and instructions carefully before operating equipment. Warning: This unit is equipped with an internal

More information

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (300, 500, 600 & 800 Series) WARNING

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (300, 500, 600 & 800 Series) WARNING Safe Operation Practices Set-Up Operation Service Troubleshooting OPERATOR S MANUAL Snow Thrower 2-Stage and 3-Stage (300, 500, 600 & 800 Series) Table of Contents Safe Operation Practices... 2 Assembly

More information

ITEM # V CORDLESS SNOW SHOVEL MODEL #KSS 1280B-06 Español p. 19. ATTACH YOUR RECEIPT HERE Serial Number. Purchase Date

ITEM # V CORDLESS SNOW SHOVEL MODEL #KSS 1280B-06 Español p. 19. ATTACH YOUR RECEIPT HERE Serial Number. Purchase Date ITEM #0533632 80 V CORDLESS SNOW SHOVEL MODEL #KSS 1280B-06 Español p. 19 ATTACH YOUR RECEIPT HERE Serial Number Purchase Date Questions, problems, missing parts? Before returning to your retailer, call

More information

TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL

TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL TP300 INDUSTRIAL TRASH PUMP OPERATOR S MANUAL IT IS EXTREMELY IMPORTANT TO READ AND UNDERSTAND THE ENTIRE CONTENTS OF THIS OPERATOR S MANUAL BEFORE ATTEMPTING TO OPERATE THE PRODUCT. THIS EQUIPMENT IS

More information

Sno-Thro. Platinum Series. Operator s Manual Manuel du Utilisateur. Models Platinum SHO 24 (SN ) Platinum SHO 30 (SN )

Sno-Thro. Platinum Series. Operator s Manual Manuel du Utilisateur. Models Platinum SHO 24 (SN ) Platinum SHO 30 (SN ) Operator s Manual Manuel du Utilisateur Platinum Series Models 921050 Platinum SHO 24 (SN 035000 +) 921051 Platinum SHO 30 (SN 035000 +) 921057 Platinum SHO 28 RapidTrak (SN 000101 +) Sno-Thro E10 ENGLISH

More information

Package Contents Part A (3) I-Beam (1) Base (2) Other parts

Package Contents Part A (3) I-Beam (1) Base (2) Other parts Page 1 Installation Instructions for 81245 Adjustable Height Gantry Crane 1-Ton Capacity Table of Contents Important Safety Information pg. 2 Specific Operation Warnings pg. 2 Main Parts of Product pg.

More information

P. O. BOX 1386, 97 KENT AVENUE, KITCHENER, ONTARIO N2G 4J1

P. O. BOX 1386, 97 KENT AVENUE, KITCHENER, ONTARIO N2G 4J1 www.troybilt.ca Operator s Manual Two Stage Snow Thrower 33 Model Shown IMPORTANT: Read safety rules and instructions carefully before operating equipment. P. O. BOX 1386, 97 KENT AVENUE, KITCHENER, ONTARIO

More information

Operating and Assembly Manual

Operating and Assembly Manual Model 455-IC/PRO/H Operating and Assembly Manual Palmor Products Inc. 5225 Serum Plant Road Thorntown, IN 46071 03-08-12 SAFETY RULES Remember, any power equipment can cause injury if operated improperly

More information

PARTS LIST. Craftsman 5.5 HP Snow Thrower Model

PARTS LIST. Craftsman 5.5 HP Snow Thrower Model 24 Craftsman 5.5 HP Snow Thrower Model 24.88355 1. 31-2635 Snow Removal Tool Mount 2. 684-0405 Impeller Assembly, 12 Dia. 3. 10-034 Hex Screw, 3/8-16, 1.5, Gr5 4. 10-0451 Bolt, Carriage, 5/16-18,.50 Gr1

More information

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (300, 500, 600 & 800 Series)

Safe Operation Practices Set-Up Operation Service Troubleshooting. Snow Thrower. 2-Stage and 3-Stage (300, 500, 600 & 800 Series) Safe Operation Practices Set-Up Operation Service Troubleshooting Operator s Manual Snow Thrower 2-Stage and 3-Stage (300, 500, 600 & 800 Series) Table of Contents Safe Operation Practices... 2 Assembly

More information

SINGLE STAGE EXTENDED FRAME SNOW THROWER SERIES 0

SINGLE STAGE EXTENDED FRAME SNOW THROWER SERIES 0 Safety Instructions & Operator s Manual for SINGLE STAGE EXTENDED FRAME SNOW THROWER SERIES 0 MODELS SX5200R SX5200E MODEL NUMBER EXPLANATION S X 5 20 0 E MODEL DESIGNATION ENGINE HP ENGINE OPTIONS SERIES

More information

STOP 42"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts

STOP 42- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT. Operator's Manual. Model No Safety Assembly Operation Maintenance Parts Operator's Manual STOP 42"- 2 STAGE SNOW THROWER TRACTOR ATTACHMENT Model No. 486.248381 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 CAUTION: Before using this product,

More information

OWNERS MANUAL. Model No. LST42D 42" SNOW THROWER. Safety Assembly Operation Maintenance Parts

OWNERS MANUAL. Model No. LST42D 42 SNOW THROWER. Safety Assembly Operation Maintenance Parts OWNERS MANUAL Model No. LST42D 42" SNOW THROWER CAUTION: Read Rules for Safe Operation and Instructions Carefully Safety Assembly Operation Maintenance Parts the fastest way to purchase parts www.speedepart.com

More information

AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL. This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E

AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL. This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E AIR-COOLED DIESEL GENERATOR OWNERʼS MANUAL This manual contains important safety information. TDG2500E TDGW7000E TDG7000SE TDG4500E TDG8000-3 TDG7000SE-3 TDG7000E TDG8000E TDGW7000SE TDG7000E3 TDGW8000E

More information

Introduction. Contents. Power Max Heavy Duty 1128 OXE Snowthrower Model No Serial No and Up WARNING.

Introduction. Contents. Power Max Heavy Duty 1128 OXE Snowthrower Model No Serial No and Up WARNING. Form No. 3373-565 Rev A Power Max Heavy Duty 1128 OXE Snowthrower Model No. 38680 Serial No. 313000001 and Up Operator's Manual Introduction This machine is intended to be used by residential homeowners

More information

Service Guide. Deluxe Series Sno-Thro. Models Deluxe 24 (SN ) Deluxe 28 (SN ) Deluxe 30 (SN )

Service Guide. Deluxe Series Sno-Thro. Models Deluxe 24 (SN ) Deluxe 28 (SN ) Deluxe 30 (SN ) Service Guide Deluxe Series Sno-Thro Models 921045 Deluxe 24 (SN 000101 +) 921046 Deluxe 28 (SN 000101 +) 921047 Deluxe 30 (SN 000101 +) 921048 Deluxe 28 SHO (SN 000101 +) 921049 Deluxe 30 EFI (SN 000101

More information

Introduction. Safety. CCR 3650 GTS Snowthrower. Training. Warning. Operator's Manual. CALIFORNIA Proposition 65 Warning

Introduction. Safety. CCR 3650 GTS Snowthrower. Training. Warning. Operator's Manual. CALIFORNIA Proposition 65 Warning CCR 3650 GTS Snowthrower Form No. 3353-578 Rev A Model No. 38517 Serial No. 260010001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product

More information

824 XL Power Throw Snowthrower

824 XL Power Throw Snowthrower Form No. 3322-84 824 XL Power Throw Snowthrower Model No. 38086 20000000 and Up Operator s Manual Pour obtenir gratuitement une version en français de ce manuel, écrivez à l adresse ci-dessous. N oubliez

More information

Sno-Thro. Platinum Series. Operator s Manual Manuel du Utilisateur. Models Platinum SHO 24 (SN ) Platinum SHO 30 (SN )

Sno-Thro. Platinum Series. Operator s Manual Manuel du Utilisateur. Models Platinum SHO 24 (SN ) Platinum SHO 30 (SN ) Operator s Manual Manuel du Utilisateur Platinum Series Models 921050 Platinum SHO 24 (SN 000101 +) 921051 Platinum SHO 30 (SN 000101 +) 921052 Platinum SHO 28 Track (SN 000101 +) Sno-Thro E10 ENGLISH

More information