Transcription

1

2

3 Parts Manual for (L.E.) SINGLE STAGE SNOW THROWER SERIES 0 MODELS LE3170R LE3170E LE30R LE30E ELE30R 30M ( ) 30E ( ) IT IS THE POLICY OF SNAPPER TO IMPROVE ITS PRODUCTS WHENEVER IT IS POSSIBLE AND PRACTICAL TO DO SO. WE RESERVE THE RIGHT TO MAKE CHANGES OR ADD IMPROVEMENTS AT ANY TIME WITHOUT INCURRING ANY OBLIGATION TO MAKE SUCH CHANGES ON PRODUCTS MANUFACTURED PREVIOUSLY. COPYRIGHT 2003 SNAPPER PRODUCTS INC. ALL RIGHTS RESERVED (Rev. 9, 06/17/03) MANUAL No

4 HARDWARE BAGS LOCATION HARDWARE BAG (Model ELE30R) (incl. below items) SCREW, 5/16-18 x 3/4 Hex Head Cap, Grade 5 (2) pages 4 & 5, item BOLT, 5/16-18 x 1-1/4 Square Neck Carriage (2) page 3, item NUT, 5/16-18 Hex Flange Lock (3) page 4 & 5, item SCREW, #8-32 x 1/2 Pan Head Cross Recess pages 4 & 5, item BOLT, 5/16-18 x 3/4 Square Neck Carriage, Grade 5 pages 4 & 5, item NUT, #8-32 Hex w/external Tooth Washer pages 4 & 5, item 17 LOCATION HARDWARE BAG (Models LE3170R, LE30R, LE30E, 30M & 30E) (includes items listed below) SCREW, 5/16-18 x 3/4 Hex Head Cap, Grade 5 (2) pages 4 & 5, item BOLT, 5/16-18 x 1-1/4 Square Neck Carriage (2) page 3, item NUT, 5/16-18 Hex Flange Lock (3) pages 4 & 5, item BOLT, 5/16-18 x 3/4 Square Neck Carriage, Grade 5 pages 4 & 5, item MANUAL No (L.E.) SNOW THROWERS SERIES 0 2

5 HANDLES, AUGER CONTROL * BAIL, Drive Control *NOTE: The heads of item carriage CABLE, Drive Control bolts mount inside the auger CLIP, Wiring Harness housing (item 1 on page 4) HANDLE, Upper INSERT, Nylon (2) KNOB, 5/16-18 Wing (Black) (2) HANDLE, Lower BOLT, 5/16-18 x 1-3/8" Curved Head (2) NUT, 5/16-18 Hex Flange Lock, Grade 5 (2) BOLT, 5/16-18 x 2" Curved Head, Grade 2 (2) NUT, 5/16-18 Hex (2) BOLT, 5/16-18 x 1-1/2 Square Neck Carriage, Grade 5 (2) WASHER, 5/16 Split Lock (2) WASHER, 5/16 Internal Tooth Lock (2) (L.E.) SNOW THROWERS SERIES 0 MANUAL No

6 DISCHARGE CHUTE, DEFLECTOR, CONTROL HANDLE DECAL, Danger Chute Deflector or DECAL, Chute Deflector, Read Manual, Euro DECAL, Safety Instructions, DECAL, Safety Instructions or DECAL, Chute, Euro MANUAL No (L.E.) SNOW THROWERS SERIES 0 4

7 DISCHARGE CHUTE, DEFLECTOR, CONTROL HANDLE CHUTE, Discharge, with inserts (shown) (Model ELE30R) CHUTE, Discharge, with inserts (Includes Decal # ) (Models LE3170R, LE30R and LE30E) CHUTE, Discharge, with inserts (Models 30M and 30E) DEFLECTOR, Chute (Includes Decal # ) (Model ELE30R) DEFLECTOR, Chute (Includes Decal # ) (Models LE3170R, LE30R, LE30E, 30M and 30E) SCREW, 5/16-18 x 3/4" Hex Head Cap, Grade 2 (2) BOLT, 5/16-18 x 1" Short Neck Carriage, Grade WASHER, 5/16 Flat (3) NUT, 5/16-24 Hex Center Lock, Grade B KNOB, 5/16-18 Wing (Black) SCREW, 5/16-24 x 3/4" Hex Head Cap, Grade 5 (2) HANDLE, Chute Control BOLT, 5/16-18 x 1-1/2 Square Neck Carriage (2) NUT, 5/16-18 Hex Flange Lock, Grade 5 (3) BOLT, 5/16-18 x 3/4" Short Neck Carriage, Grade WIRE, Safety FASTENER, Push On.156 Internal Diameter CLIP, Guard (Tinnerman #C2980) (3) SCREW, #8-32 x 1/2 Pan Head Cross Recess (3) NUT, #8-32 Hex (with free spinning external lock washer) (3) (L.E.) SNOW THROWERS SERIES 0 MANUAL No

8 AUGER HOUSING, DRIVE SYSTEM, CHASSIS * *NOTE: IF REPLACING ITEM 5 BELT GUARD INSTALL (2) ITEM 44 HEX SPACERS & HARDWARE MANUAL No (L.E.) SNOW THROWERS SERIES 0 6

9 AUGER HOUSING, DRIVE SYSTEM, CHASSIS ASS Y, Auger Housing (17 Model) ASS Y, Auger Housing (" Non- Euro Models) ASS Y, Auger Housing (ELE30R) ASS Y, End Frame (L.H.) (17" Mods ASS Y, End Frame (L.H.) (" Mods) FRAME, End (R.H.) (17" Models) FRAME, End (R.H.) (" Models) COVER, R.H. Side (17" Models) COVER, R.H. Side (" Models) GUARD, Belt Drive (Fits All Models See Note Below) ASSEMBLY, Auger (17" Models) (Includes Items 49 Thru 52) ASSEMBLY, Auger (" Models) (Includes Items 49 Thru 52) SCREW, 5/ x 5/8" Self-Tapping WASHER, 5/16 Flat (3) BEARING, Ball (2) RETAINER, 1-3/4 O.D.. Bearing (2) WASHER, 3/4 Shim (2) SCREW, #10-32 x 3/8" Self-Tapping (Torx) (9) PULLEY BRACE, Engine SCREW, 1/4-20 x 3/8" Hex Washer Self-Tap (2) BOLT, 5/16-18 x 3/4" Square Neck Carriage (Grade 5) COVER, Wheel (2) ('94 Model Year & Earlier) NUT, 5/16-18 Hex Flange Lock (4) SCREW, 1/4-15 x 1" Hex Washer Self-Tap (4) WASHER, 5/16 Split Lock (7) NUT, 5/16-18 Hex, Grade B or 5 (5) PULLEY, Engine SCREW, 5/16-24 x 3/4" Hex Head Cap, (Grade 5) V-BELT, 3L, E.F. (Snapper part no. printed on belt) GUIDE, Cable (17" Models) GUIDE, Cable (" Models) BUSHING, Flange PULLEY, Nylon GUIDE, Belt NUT, 5/16-18 Hex Center Lock (2) BRACKET, Idler Pivot PULLEY, Idler (" Models) PULLEY, Single Flange Idler (17") SCREW, 5/16-18 x 1-3/4" Hex Cap (Grade 5) SPRING, Idler Torsion BUSHING, Pivot SCREW, #10-16 x 3/4" Pan Head Self-Tap(3) AXLE, 3/8" Dia. Wheel WASHER, 3/8 Flat (4) WHEEL, 7 x 1.50 (2) WHEEL, 7 (2) (30M & 30E) NUT, 3/8 Push (2) WASHER, #10 Flat (5) SUPPORT, Fuel Tank BOLT, 1/4-20 x 5/8" Short Neck Carriage, Grade NUT, 1/4-20 Hex (Nyloc) SPACER, Hex (2.69" Long) (17" Models) (2) SPACER, Hex (3.69" Long) (" Models) (2) BLADE, Scraper (17" Models) BLADE, Scraper (" Models) SCREW, 1/4-20 x 1/2" Machine (4) NUT, 1/4-20 Hex Center Lock, Grade B or 5 (4) NUT, 1/4-20 Hex Center Lock (2) STRUCTURE, Auger (17" Models) STRUCTURE, Auger (" Models) SHOE, Flite (4) (17" Models) SHOE, Flite (4) (" LE Models) SHOE, Flite (4) (30M & 30E) SHOE, Center Flite (2) SCREW, #10-24 x 1/2" Hex Washer Self-Tap Sems (24) WASHER, 5/16 Internal Tooth Lock WASHER, 1/4 Split Lock WASHER, 3/4 Flat (2) WASHER, 11/32" (3) NOTE: 94 & EARLIER MODELS USE A DIFFERENT BELT GUARD & ONE HEX SPACER. IF REPLACING ITEM 5 BELT GUARD INSTALL (2) ITEM 44 HEX SPACERS & HARDWARE. (L.E.) SNOW THROWERS SERIES 0 MANUAL No

10 COVERS, ENGINE DETAIL FOR ASSEMBLING STARTER T PLUG TO COVER STARTER PLUG NUTS SCREWS COVER 3 18 WASHERS SEE PAGE 6 & 7 FOR FUEL TANK SUPPORT SEE PAGE 15 FOR ELECTRIC START COMPONENTS SEE PAGE 6 & 7 FOR END FRAME MANUAL No (L.E.) SNOW THROWERS SERIES 0 8

11 COVERS, ENGINE COVER, Top (Includes Eyelet # ) (all except 30M & 30E) COVER, Top (Includes Eyelet # ) (30M & 30E) ASSEMBLY, Fuel Tank (Includes # Cap) SPACER SCREW, 1/4-20 x 1/2" Machine (replaced by item #23 on new models) NUT, 5/8-32 Hex NUT, 1/4-20 Hex Flange Lock KEY (pair) SWITCH, Ignition PRIMER HOSE, Primer PLUG, Hole CLAMP, Fuel Hose (2) HOSE, Fuel 8-1/2" Long (2) ENGINE, 3 HP Tecumseh (HSK T) (17" Models) (Engine Crank Shaft " Long) ENGINE, 3 HP Tecumseh (HSK T) (" Models) (Engine Crank Shaft " Long) ENGINE, 3 HP Tecumseh (HSK T) (" Models) (Engine Crank Shaft " Long) (electric start) KEY, 5/32 x 5/8" Woodruff COVER, Bottom (Recoil Start Models) COVER, Bottom (Electric Start Models) SCREW, #10-24 x 1/2" Hex Washer Self-Tap (Torx) (2) HANDLE, Pull Rope ('94 Model Year and Earlier) HANDLE, Pull Rope ( 95 Model Year and Later) HANDLE, Pull Rope (30M & 30E Models) (not shown) SCREW, #8 x 1-1/4" Hi-Lo Self-Tapping (2) WASHER, 5/8 Internal Tooth Lock FILTER, In-Line SCREW, 1/4-20 x 3/4" Hex Head Cap, Grade 5 (3) (was 90073) ISOLATOR, Fuel Tank/Cover SPACER WASHER, #10 Flat (4) (Electric Start Models Only) WASHER, 1/4 Split Lock INSERT, Starter Handle ('95 Model Year and Later) MUFFLER STUD, LE MUFFLER STUD, LE3 (not shown) KNOB, Red BEZEL (L.E.) SNOW THROWERS SERIES 0 MANUAL No

12 DECALS ('94 MODEL YEAR AND EARLIER) DECAL, Panel Instruction (Recoil Start) DECAL, Panel Instruction (Electric Start) DECAL, 17" Models (Recoil Start) DECAL, 17" Models (Electric Start) DECAL, " Models (Recoil Start) DECAL, " Models (Electric Start) DECAL, Safety Instruction DECAL, Danger DECAL, SNAPPER (Top Cover) DECAL, SNAPPER (Belt Cover) DECAL, Primer Instruction LOGO, SNAPPER 11 MANUAL No (L.E.) SNOW THROWERS SERIES 0 10

13 DECALS ( 95 MODEL AND LATER) DECAL, Panel Instructions (Electric Start) DECAL, Panel Instructions (Recoil Start) DECAL, Panel Instructions (Euro) DECAL, Panel Instructions (Recoil Start) DECAL, Panel Instructions (Electric Start) DECAL, Auger Control DECAL, Auger Control (Euro) DECAL, Ear Protection (L.E.) SNOW THROWERS SERIES 0 MANUAL No

14 DECALS ( 95 MODEL AND LATER) (Continued) DECAL, Snapper (Belt Cover) (13 long) DECAL, Snapper (Belt Cover) (15 long) LOGO, Snapper DECAL, L. E. Model DECAL, 17 Model DECAL, Model DECAL, Chute, Safety Instructions DECAL, Chute (Euro) DECAL, Danger, Chute Deflector DECAL, Deflector, Read Manual (Euro) DECAL, Sound (110 db) DECAL, Sound (105 db) MANUAL No (L.E.) SNOW THROWERS SERIES 0

15 DECALS ( 95 MODEL AND LATER) (Continued) DECAL, Warning Safety Instructions DECAL, Primer Instruction DECAL, Primer Instruction (Euro) DECAL, Fuel Safety DECAL, Euro Community DECAL, Foot/Danger (Euro) DECAL, Tec. 3HP Carb/EPA Certified (Tecumseh P/N ) DECAL, 2002 Year of Manufacture DECAL, 2003 Year of Manufacture DECAL, Caution Tag (L.E.) SNOW THROWERS SERIES 0 MANUAL No

16 DECALS ( 95 MODEL AND LATER) (Continued) DECAL, Panel Instruction (Electric Start) DECAL, Panel Instruction (Recoil Start) DECAL, Top Cover, Left Hand DECAL, Top Cover, Right Hand DECAL, Primer Instruction/Key Switch DECAL, Top Cover, Front DECAL, Tec. 3HP Carb/EPA Certified MANUAL No (L.E.) SNOW THROWERS SERIES 0 14

17 ACCESSORIES 1 ELECTRIC START KIT 2 Tecumseh No FT. CORD INCLUDED WITH STARTER KIT (Tecumseh Part Numbers 1A or B) Snapper P/N (for LE3170E & LE30E) or Snapper P/N (for model 30E) KIT, Electric Start (Tecumseh P/N ) SCREW, #10-24 x 1-3/4" Phillips Pan Head (2) WASHER, #10 Flat (4) NUT, #10-24 Hex Flange Lock (2) *Parts Available Only From Engine Manufacturer. 17" FLITE SHOE KIT KIT, Flite Shoe (Includes Items 1 Thru 4) SHOE, 17" Flite Auger SHOE, Flite Center SCREW, 1/4-20 x 1/2" Machine (24) NUT, 1/4-20 Hex Center Lock, Grade 5 or B (24) NOTE: Items 3 and 4 above were used on early models, but were replaced by Self-Tapping Screws (P/N 70986)on later models " FLITE SHOE KIT KIT, Flite Shoe (Includes Items 1 Thru 4) SHOE, " Flite Auger SHOE, Flite Center SCREW, 1/4-20 x 1/2" Machine (28) NUT, 1/4-20 Hex Center Lock, Grade 5 or B (28) NOTE: Items 3 and 4 above were used on early models, but were replaced by Self-Tapping Screws (P/N 70986)on later models (L.E.) SNOW THROWERS SERIES 0 MANUAL No

18