THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY. 3. Sizes: YM / YL / XS / S / M / L / XL / XXL 63

Transcription

1 THE UNITED KINGDOM VEHICLE APPROVAL AUTHORITY COMMUNICATION CONCERNING THE APPROVAL GRANTED (1) / APPROVAL EXTENDED (1) / APPROVAL REFUSED (1) / APPROVAL WITHDRAWN (1) / PRODUCTION DEFINITELY DISCONTINUED (1) OF A TYPE OF PROTECTIVE HELMET WITH/WITHOUT (1) / ONE/MORE THAN ONE (1) / VISOR TYPE(S) PURSUANT TO REGULATION NO E11 Approval No: 22R /P Extension No: Not applicable Reason for extension: Not applicable 1. Trade mark: LEATT 2. Type: GPX 5.5 ECE 3. Sizes: YM / YL / XS / S / M / L / XL / XXL Manufacturer's name: Leatt Corporation 5. Address: No. 50 Kiepersol Crescent Atlas Gardens Durbanville 7550 Cape Town Republic of South Africa 6. If applicable, name of manufacturer's representative: Not applicable 7. Address: Not applicable 8. Brief description of helmet: See enclosures 9. without lower face cover (J) / with protective lower face cover (P) / with non protective lower face cover (NP) (1) MAR An executive agency of the Department for Transport June 2015 Revision 5 1

2 E11 22R /P 10. Type of visor or visors: Not applicable 11. Brief description of visor or visors: Not applicable 12. Submitted for approval on: 15 July Technical service responsible for conducting approval tests: Omega S.r.l. 14. Date of report issued by that service: 13 October Number of report issued by that service: MAR Comments: None 17. Approval GRANTED/EXTENDED/REFUSED/WITHDRAWN (1) 18. Place: BRISTOL 19. Date: 23 DECEMBER Signature: D LAWLOR Head of Technical Standards & Legislation 21. The following documents, bearing the approval number shown above, are available on request Any remarks: Approval to Supplement 2 (1) Strike out what does not apply. MAR An executive agency of the Department for Transport June 2015 Revision 5 2

3 LEATTT CORPORATION TECHNICAL FILE 70 REVISION 01 PERSONAL PROTECTIVE P EQUIPMENT HELMET LEATT G GPX 5.5 ECE COMPOSITE Prepared by Leatt -Lab September 2016 R& &D Department Document No: TF Revision 01 Leatt Corporation

4 Leatt Corporation Technical File 39 R 01 TABLE OF CONTENTS GENERAL INFORMATION 1. File number, revision status an date 2. Manufacturers Name & Address 3. Company Representative 4. Address of manufacture or assembly 5. Trade Mark 6. Type 6.1 Type PRODUCT INFORMATION 7.1 Parts list 7.2 Product Pictures 7.3 Product Description (base model) Product Description (variant models) 7.4 Shell Materials 7.5 Liner 7.6 Padding 7.7 Accessories 7.8 Retention System 7.9 Reflective Stickers 7.10 Weight 8. Drawings and General assembly of product 9. Outline of method of manufacture 10. Sizing 11. Labelling 11.1 Applicant's statement of labelling 11.2 Examples of product labels ANNEXURE A - MANUFACTURER s INFORMATION ANNEXURE B DRAWINGS & GENERAL ASSEMBLY Document Change Log Leatt GPX 5.5 Composite Page 2

5 Leatt Corporation Technical File 39 R 01 GENERAL INFORMATION 1. File Number: 70 Revision Status: R 01 Date: 23 November Manufacturer s name and address Leatt Corporation (South Africa) No. 50 Kiepersol Crescent Atlas Gardens Durbanville 7550 Cape Town Republic of South Africa 3. Company representative not applicable 4. Name and address of assembly plant Dongguan Strategic Sports Ltd. Liu Huang Industrial Area Chasan Town Dongguan City, Guangdong Province, China Tel: , Fax: helmets@helmets.com.hk 5. Trade Mark LEATT 6. Type GPX 5.5 ECE 6.1 Type Motocross providing head protection for motorcyclists meeting the requirements of ECE ECE Regulation - Uniform Provisions Concerning the approval of protective helmets and their visors for drivers and passengers of motor cycles and mopeds. Leatt GPX 5.5 Composite Page 3

6 Leatt Corporation Technical File 39 R 01 PRODUCT INFORMATION 7.1 Parts list See Annexure B 7.2 Product Pictures Examples of the GPX 5.5 Composite Adult Leatt GPX 5.5 Composite Page 4

7 Leatt Corporation Technical File 39 R 01 Example of the GPX 5.5 Junior Leatt GPX 5.5 Composite Page 5

8 Leatt Corporation Technical File 39 R Product Description (base model) The Leatt GPX 5.5 Series is an innovative approach to head protection that significantly reduces the physical size and weight of the helmet and the negative effects of rotational impacts. It features a viscous-elastic polymer material called Armourgel that is built into a circular array of impact-absorbing spacers placed between the rider s head and the helmet s padded EPS liner to help control head rotation within the helmet liner while protecting the brain from low energy impacts - considered to be the leading cause of concussions among off-road motorcycle riders. About the size of a US quarter, these Turbine 360 buttons fulfil two critical duties. The energy absorbing material slows low-speed impacts well before the head contacts the EPS liner, while the spoked 'turbine' design allows the head to rotate slightly inside the helmet, should the rider receive a glancing blow. The helmet is also engineered to reduce the thickness necessary to mute forceful impacts by utilizing a dual density in-moulded EPS liner called V-Foam construction that utilizes a harder, outer layer of EPS foam that is moulded directly into the rigid outer shell of the helmet and co-moulded to a second, softer EPS layer which has a number of conical spikes which nest into it. The three elements: in-moulding, dual-density EPS foam and the conical spikes, dramatically reduce the thickness necessary to mute impact force, so the helmet can be made much smaller and lighter weight - which is an additional benefit in the case of a whiplash or a rotational impact. Leatt GPX 5.5 Composite helmets are 5 to 20-percent smaller in profile than major competitors. Features: Reduced outer shell volume for reduction in neck forces and rotational brain acceleration. Optimized integration with Leatt neck braces: degree helmet and neck brace match - Rear clearance cut for riding - Rear hyperextension impact platform Optimized weight. Very light with great safety: - Maximum ventilation - 11 large vent ports - Estimated weight for Size #M: 1.095g +/- 50g Hydration ready. Optional internal hands free kit available Anti-microbial high evaporating snap out liner system: - Dri-Lex Tech layer - Visor with break-away function - LEATT Race Ready Design prepared for ejection helmet removal system Product Description (variant models) None at present. Leatt GPX 5.5 Composite Page 6

9 Leatt Corporation Technical File 39 R Shell Materials Composite Fibres 7.5 Liner EPS (Expanded Polystyrene) 7.6 Padding Moulded EVA Armourgel 360⁰ turbines 7.7 Accessories - Hydration ready Optional internal hands free kit available - Zero friction removable safety cheek pads - Peak with break-away function 7.8 Retention System - Double D type retention system, made in Aluminium. See drawings in annexure B for more details. 7.9 Reflective Bands - See report number Report-0265EU15 with reflective qualities and drawings in annexure B for design details Weight The following weights have been defined with a tolerance of ± 50g Sizes Weight [g] Youth YM 960 Adult XS / S 1050 Adult M / L 1110 Adult XL / XXL 1185 Leatt GPX 5.5 Composite Page 7

10 Leatt Corporation Technical File 39 R Drawings and General assembly of product General dimensions: Shell EPS Size Width Length Height Width Length Height YM YL / XS / S M/L XL/XXL Please refer to Annexure B for drawings and assembly details. This is a direct extract from the Leatt data pack with unnecessary detail removed. 9. Outline of method of manufacture: Material testing and cutting, assembly order and the inspections that are made, finishing and inspection Leatt Corporation applies quality management with due regard to ISO Quality procedures detail the type and quantity of inspections to be performed on production runs, including a requirement for sampling of all products, components and manufacturing processes at each stage of production; plus a requirement for testing of completed products at regular intervals, or where there are concerns that a serious non-compliance may have occurred. Leatt Quality personnel are directly involved in the guidance and training of supplier Factory Quality teams where necessary. Materials and components from non-iso 9001 accredited suppliers are checked for conformity before being moved to the stores. For such suppliers, a sample representing 5% of a shipment quota is checked and after passing inspection shipments are stored in a specific area. For ISO 9001 accredited suppliers, the inspection is 0.5%, selected at random and checked in the manner described above. Materials are required to be within the tolerances of the LEATT specifications and designs. In the event of non-conformity, either the entire shipment is repackaged (marked clearly as rejected ), quarantined, and returned to the supplier for rework or credit or subject to 100% inspection and non-conforming materials removed and rejected. All fabrics and lining materials are cut to size from templates to an accuracy of ± 3%. Continual visual checks are made, usually following each cutting operation, to ensure that the pattern has not been damaged or otherwise dimensionally-changed due to wear and tear. Components for products of the same variant type and size are prepared at the same time, or are prepared on physically separated production lines. Components are clearly tagged or otherwise marked with the variant type and size, and at all stages of the manufacturing process are kept completely separate from other components for different product variants and sizes. If at all possible, production of different variants and sizes does not take place at the same time. Assembly is performed in accordance with the procedures specified in Leatt Corporation s Production Manuals. Constant visual inspections are made to ensure that All components are for the correct, same variant and size of product All badges and labels are fitted Leatt GPX 5.5 Composite Page 8

11 Leatt Corporation Technical File 39 R 01 All completed products are then submitted for Final Inspection, where checks are made to ensure that the correct assembly specification has been met. Where this is the case, swing tickets, including warning labels, are attached by one or more nylon tags and the product is placed within packaging. Should a non-conformance be discovered, however, a rejected label is attached to the product, with an explanation of the non-conformance written on the reverse of the label, and returned to the assembly department for corrective action. 10. Sizing The products described in this Technical File are available to fit a broad range of head sizes. Model Size Head Size Shell EPS Youth M (Medium) 51-52cm Youth Youth Youth L (Large) 53-54cm Adult XS (Extra Small) 53-54cm Small Small Adult S (Small) 55-56cm Adult M (Medium) 57-58cm Adult L (Large) 59-60cm Medium Medium Adult XL (Extra Large) 61-62cm Adult XXL (Extra Extra Large) 63 cm Large Large 11. Labelling 11.1 Applicant's statement of labelling The following information will be clearly affixed to the helmet, in a visible place and respecting the location and dimensions required by the applicable standards. Product brand and variant identification (e.g. " GPX 5.5 ECE Composite ); The appropriate Certification markings as required by the applicable standards; A size designation in accordance with the applicable standards A means of identifying the date of manufacture, such as a batch number. Its maximum weight, to the nearest 50 grams, as placed on the market. Leatt GPX 5.5 Composite Page 9

12 Technical File for EC Type-Examination Leatt Corporation PERSONAL PROTECTIVE EQUIPMENT GPX 5.5 Composite Series ANNEXURE A MANUFACTURER s INFORMATION See following enclosures for the Manufacturer s information: Owner s Manual

13 Technical File for EC Type-Examination Leatt Corporation PERSONAL PROTECTIVE EQUIPMENT GPX 5.5 Composite Series ANNEXURE B TECHNICAL DRAWINGS See following enclosures for Technical Drawings: Assembly Drawings Detail Drawings Rev 1 Shell Drawings EPS Drawings Cone-Head EPS Chin Strap with dimensions D-ring details Reflective Sticker

14 REVISION LOG Document TF CE Leatt Corporation Technical File 70 HELMET GPX 5.5 COMPOSITE SERIES Rev Number Date Page#, Section Reason for Change September-2016 All pages Preliminary Draft for comment November-2016 Section 8 Complete information about helmet dimensions Name: Position: Signature: Pieter-André Keevy Biomedical Engineer

15

16

17

18

19

20 B A E F C A B C D E F Shell Size S M L Attachment Point

21 Material: Stainless Steel 201

22 105mm 25mm

23 Job Number MAR QUALIFICATION TESTING UNECE n 22 Series 05 entification Test: E5HQ Code: GPX 5.5 Composite Qualification Report Date: 13 October 2016 Name: Leatt Corporation Manufacturer Address: No. 50 Kiepersol Crescent- Atlas Gardens Atlas Gardens Cape Town Republic of South Africa Representative It does not apply Sample model: Approval n : GPX ECE 22R /P Stickers from n : 1 to n : 3200 Batch n : 1 Arrival date: 12/10/2016 Testing date: 13/10/2016 Essential Technical Data SIZE RANGE XS(54) to XXL (63) SHELL MATERIAL Composite Fibres WEIGHT XS: 1050gr / XXL: 1185gr RETENTION SYSTEM DD ring REFLECTIVE BANDS Yes ENVIRONMENTAL CONDITIONS Temperature 17.8 Humidity 49.3% Used Machine Identifier /Manufacturer Expiring Date M0015 Tracking point of impact LTB 1079 (AD Engineering) Daily Check IO A0059/M0003 Shock absorption MAU 1006E/DLS 9000 (AD 08/11/2016 Engineering) M0044 Chin strap resistance MSD 1009 (AD Engineering) 10/10/2019 M0001 Conditioning chamber: T616/40 (OCRAS E ZAMBELLI) 09/09/2017 Freezer M0075 Conditioning chamber: Oven ABX 700NE(IARP) 09/09/2017 Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 1/7

24 The helmets are divided in n 6 batches 10 Group n Size helmets 1 The largest size 10 2 The largest size 10 3 The largest size 10 4 The largest size 10 5 The largest size 10 6 The smallest size 10 Sticker n Standardabweichung / Standard deviation Bedingung / Condition Gruppe / Batch n 1 size: XXL Headform size: 62 Impact point: B Anvil: FLAT Condition ing [ C] Speed [m/s] Real speed [m/s] <= HIC 2400 <= Deceleration 275 [g] 7, , , , , , , , , , g m = g i / S g m 1 2 [ ( g ) / 9] 2 i g = m S Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 2/7

25 Gruppe / Batch n 2 size: XXL Headform size: 62 Impact point: X Anvil: FLAT Sticker Condition Speed Real speed HIC Deceleration n ing [ C] [m/s] [m/s] <= 2400 <= 275 [g] , , , , , , , , , Mittelwert / Mean of the value g = / m g i Standardabweichung / Standard deviation Bedingung / Condition S g m 1 2 [ ( g ) / 9] 2 i g = m S Gruppe / Batch n 3 size: XXL Headform size: 62 Impact point: P Anvil: FLAT Sticker n Condition ing [ C] Speed [m/s] Real speed [m/s] <= HIC 2400 <= Deceleration 275 [g] , , , , , , , , , Mittelwert / Mean of the value g = / m g i Standardabweichung / Standard deviation Bedingung / Condition S g m 1 2 [ ( g ) / 9] 2 i g = m S Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 3/7

26 Gruppe / Batch n 4 size: XXL Headform size: 62 Impact point: R Anvil: FLAT Sticker n Condition ing [ C] Speed [m/s] Real speed [m/s] <= HIC 2400 <= Deceleration 275 [g] , , , , , , , , Mittelwert / Mean of the value g = / m g i Standardabweichung / Standard deviation Bedingung / Condition S g m 1 2 [ ( g ) / 9] 2 i g = m S Gruppe / Batch n 5 size: XXL Headform size: 62 Impact point: S Anvil: FLAT Sticker Condition Speed Real speed HIC Deceleration n ing [ C] [m/s] [m/s] <= 2400 <= 275 [g] , , , , ,50 5, , , , , , Mittelwert / Mean of the value g = / m g i Standardabweichung / Standard deviation Bedingung / Condition S g m 1 2 [ ( g ) / 9] 2 i g = m S Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 4/7

27 RETENTION SYSTEM STRENGTH TEST Gruppe / Batch n 6 size: XS DD ConditioningAMB Stickers n Din. Exten. Res. Exten. <=35 [mm] <=25 [mm] Xm 23,2 11,4 S 1,0 1,9 Xm+2,4*S Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 5/7

28 INFORMATION FOR WEARERS Ref. 14 LABELLING Result Reference Test Description or image Method of Attachment to helmet at point of sale: Specifies the following: "For adequate protection, this helmet must fit closely and be securely attached. Any helmet that has sustained a violent impact should be replaced" if fitted with a non protective lower face cover: "Does not protect chin from impacts" together with the symbol indicating the unsuitability of the lower face cover to offer any protection against impacts to the chin specific warning in the above-mentioned label: " 'Warning' - Do not apply paint, stickers, petrol or other solvents to this helmet" Bears a label showing the type or types of visor that have been approved at the manufacturer's request: PASS NAP PASS NAP Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 6/7

29 MARKING Result Reference Test Description or image Method of Marking to the helmet: -.. Specifies the following: 14.3 Protective helmet is clearly marked with its size and its maximum weight, to the nearest 50 grams, as placed on the market. THE SAMPLES TESTED MEET THE REQUIREMENTS OF THE REFERENCE NORM Laboratory Technician (Adolfo Garlando) Laboratory Manager (Juan Pablo Cuesta) Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 7/7

30 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale Job Number MAR CERTIFICATION TESTING UNECE n 22 Series 05 entification Test: E5HC Code: GPX 5.5 ECE Homologation Report Date: 08 August 2016 Name: Leatt Corporation Manufacturer Address: No. 50 Kiepersol Crescent- Atlas Gardens Atlas Gardens Cape Town Republic of South Africa Representative It does not apply Sample model: Approval n : - GPX 5.5 ECE Stickers from n : - to n : - Batch n : - Arrival date: 04/08/2016 Testing date: 05-08/08/2016 Essential Technical Data SIZE RANGE Youth(51-52) to XXL (63-64) SHELL MATERIAL Composite WEIGHT 1150±50(Size XXL/XL) / 1050±50(Size L/M) 1000±50(Size XS) / 920±50(Size YOUTH) RETENTION SYSTEM DD REFLECTIVE BANDS Yes ENVIRONMENTAL CONDISTIONS Temperature 24 Humidity 60% Used Machine Identifier /Manufacturer expiry Date M0015 Tracking point of impact LTB 1079 (AD Engineering) Daily Check IO A0059/M0003 Shock absorption MAU 1006E/DLS 9000 (AD Engineering) 08/09/2016 M0044 Chin strap resistance MSD 1009 (AD Engineering) 10/10/2016 M0001 Conditioning chamber: T616/40 (OCRAS E ZAMBELLI) 09/09/2016 Freezer M0075 Conditioning chamber: ABX 700NE(IARP) 09/09/2016 Oven M0030 Compressibility CTE 1068 (AD Engineering) 21/05/2020 M0033 Chin strap efficiency ROL 1103/E (AD Engineering) 27/05/2020 The helmet was tested in the different configurations with internal sun visor and other critical components. Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 1/10

31 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale GPX 5.5 ECE Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 2/10

32 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale GENERAL SPECIFICATION TEST Sizes: Youth(51-52)-XS (53-54) S (55-56) M (57-58) L (59-60) XL (61-62)-XXL(63-64) Result Reference General Specification Pass (or N/A) Fail 6.1 Hard shell X 6.1 Impact absorption system (see test data in this report) 6.1 Retention system X 6.2 Marked Does not protect chin from impacts (if applicable) N/A Extent of protection X Nape cylinder X Protective padding X 6.5 Outer round surface Auditive faculties X 6.6 Projections ( 2 mm) X 6.7 Rivets (h 2 mm, r 1 mm; h 2mm, r 2mm) 6.8 interior X 6.9 Assembly X 6.10 Chin strap abrasion X Retention system Chin strap breadth ( 20 mm) X Under-chin X Chin strap regulation system X Rigid parts X Buckle Double D or Roll X Open strip X Quick release (general requirement) NAP Quick release (tests par. 7.3, 7.6, 7.7) NAP Wrong buckle use NAP 6.12 Material properties (manufacturer declaration) X 6.13 breaking X 6.14, Peripheral vision: to Reflective parts (see test reports) Lateral visual clearance 105 X Upward visual clearance 7 X Downward visual clearance 45 X X X X Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 3/10

33 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale SPECIFICATION H.F. Size 50 to 62 Impact point B / P / X / R /S Anvil Kerbstone / Flat Conditioning [ C] AMB 20 C ± 5 C with a relative humidity of 65% ± 5%, for more than 4 hours LOW -20 C ± 5 C, for more than 4 hours and less than 6 hours HIGH +50 C ± 5 C, for more than 4 hours and less than 6 hours UV+H 2 O Ultraviolet radiation by a 125-watt xenon- 48 hours Water spray 4 to 6 hours, 1 litre per minute Speed [m/s] 7.5 m/s m/s ( m/s for the S point) HIC 2400 Deceleration 275 SHOCK ABSORPTION TESTS Ref. 7.3 size XXL(63-64)- GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. [ C] Speed [m/s] HIC 2400 Deceleration 275 [g] B FLAT X FLAT AMB P FLAT R FLAT B KERB X KERB AMB P KERB R KERB B KERB X KERB P KERB R KERB B FLAT X FLAT P FLAT R FLAT S FLAT B KERB X KERB UV +WET P FLAT R FLAT Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 4/10

34 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale size XL(61-62)- GPX 5.5 ECE Sticker n H.F. Size Impact Anvil Cond. Speed HIC Deceleration point [ C] [m/s] [g] B KERB X KERB P FLAT R FLAT B FLAT X FLAT P KERB R KERB S FLAT size L(59-60) GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. [ C] Speed [m/s] HIC 2400 Deceleration 275 [g] B FLAT X FLAT AMB P FLAT R FLAT B KERB X KERB AMB P KERB R KERB B KERB X KERB P KERB R KERB B FLAT X FLAT P FLAT R FLAT S FLAT B KERB X KERB UV +WET P FLAT R FLAT Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 5/10

35 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale size M(57-58)- GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. Speed HIC [ C] [m/s] 2400 B KERB X KERB P FLAT R FLAT B FLAT X FLAT P KERB R KERB S FLAT Deceleration 275 [g] size S(55-56) GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. [ C] Speed [m/s] HIC 2400 Deceleration 275 [g] B FLAT X FLAT AMB P FLAT R FLAT B KERB X KERB AMB P KERB R KERB B KERB X KERB P KERB R KERB B FLAT X FLAT P FLAT R FLAT S FLAT B KERB X KERB UV +WET P FLAT R FLAT Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 6/10

36 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale size XS(53-54)- GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. Speed HIC [ C] [m/s] 2400 B KERB X KERB P FLAT R FLAT B FLAT X FLAT P KERB R KERB S FLAT Deceleration 275 [g] size Youth GPX 5.5 ECE Sticker n H.F. Size Impact point Anvil Cond. [ C] Speed [m/s] HIC 2400 Deceleration 275 [g] B FLAT X FLAT AMB P FLAT R FLAT B KERB X KERB AMB P KERB R KERB B KERB X KERB P KERB R KERB B FLAT X FLAT P FLAT R FLAT S FLAT B KERB X KERB UV +WET P FLAT R FLAT Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 7/10

37 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale Sticker n RETENTION SYSTEM STRENGTH TEST Ref. 7.6 GPX 5.5 ECE Extension Size Chin strap Dynamic 35 [mm] Residual 25 [mm] XL DD Sticker n ROLL OFF TEST Ref. 7.7 Size Chin strap Roll off Angle XL DD 27 Sticker n RETENTION SYSTEM STRENGTH TEST Ref. 7.6 GPX 5.5 ECE Extension Size Chin strap Dynamic 35 [mm] Residual 25 [mm] M DD Sticker n ROLL OFF TEST Ref. 7.7 Size Chin strap Roll off Angle M DD 19 Sticker n RETENTION SYSTEM STRENGTH TEST Ref. 7.6 GPX 5.5 ECE Extension Size Chin strap Dynamic 35 [mm] Residual 25 [mm] XS DD Sticker n ROLL OFF TEST Ref. 7.7 Size Chin strap Roll off Angle XS DD 26 Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 8/10

38 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale Sticker n RETENTION SYSTEM STRENGTH TEST Ref. 7.6 GPX 5.5 ECE Extension Size Chin strap Dynamic 35 [mm] Residual 25 [mm] Youth DD 23 4 Sticker n ROLL OFF TEST Ref. 7.7 Size Chin strap Roll off Angle Youth DD 19 TEST FOR PROJECTION AND SURFACE FRICTION METHOD B Client Id Test Tested Point Result Pass Fail GPX 5.5 ECE Surface Top X - GPX 5.5 ECE Proejction Peack X - GPX 5.5 ECE Proejction Rear X RIGIDITY TEST Ref. 7.5 GPX 5.5 ECE Deformation [mm] Load Direction Sticker n Size Initial Max Final 40 [mm] 15 [mm] (load 30N) (load 630N) (load 30N) XXL Longitudinal XXL Transversal RIGIDITY TEST Ref. 7.5 GPX 5.5 ECE Deformation [mm] Load Direction Sticker n Size Initial Max Final 40 [mm] 15 [mm] (load 30N) (load 630N) (load 30N) L Longitudinal L Transversal RIGIDITY TEST Ref. 7.5 GPX 5.5 ECE Deformation [mm] Load Direction Sticker n Size Initial Max Final 40 [mm] 15 [mm] (load 30N) (load 630N) (load 30N) S Longitudinal S Transversal Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 9/10

39 Sede Legale: Strada Comunale Savonesa n Tortona Frazione Rivalta Scrivia (AL) Italy Tel Fax Partita Iva e Codice Fiscale RIGIDITY TEST Ref. 7.5 GPX 5.5 ECE Deformation [mm] Load Direction Sticker n Size Initial Max Final 40 [mm] 15 [mm] (load 30N) (load 630N) (load 30N) Youth Longitudinal Youth Transversal REFLECTIVE PARTS Reference Test Pass or N/A Reflective parts (Geometry requirements) PASS Reflective parts (Colorimetric requirements) PASS Reflective parts (Photometric requirements) PASS Reflective parts (Resistance to external agents requirements) PASS Reflective parts (Compatibility of materials requirements) PASS Result Fail THE SAMPLES TESTED MEET THE REQUIREMENTS OF THE REFERENCE NORM. Laboratory Technician (Adolfo Garlando) Laboratory Manager (Juan Pablo Cuesta) Job Number: MAR This report concerns only the tested samples and it cannot be partially reproduced without prior written permission from OMEGA s.r.l. 10/10

40 Omega VCA Declaration of Proper Procedures Annex 4 Rev. 1 VCA JOB NUMER: MANUFACTURER: TYPE: MAR Leatt Corporation GPX 5.5 ECE The undersigned confirms that the tests conducted under the above job number have been carried out in accordance with the requirements of the specified Regulation/Directive and the Licence between OMEGA S.R.L. and VCA relating to type approval testing. The undersigned has not been involved in any design nor development work on the products to be approved nor, any related product. SIGNED: NAME (in capitals): J.P. CUESTA RUIZ DATE: 16 th November th March 2016 Page 1 of 1