GenTent 10k/20k StormBracer

Transcription

1 GenTent 10k/20k StormBracer Page: 1 of 18 Product Installation and Safety Manual Free Installation Videos Read this Manual in Color Online THANK YOU Congratulations on your purchase of the GenTent StormBracer, the first ever wet weather safety canopy specifically engineered for portable generators. We are proud to provide this high-quality product.

2 Table of Contents Page: 2 of 18 TABLE OF CONTENTS... 2 IMPORTANT PRODUCT SAFETY... 3 LIMITED WARRANTY... 4 PACKAGE CONTENTS... 5 INSTALLATION OVERVIEW... 6 INSTALL GENTENT CLAMPS ON GENERATOR FRAME... 7 INSTALL GENTENT FRAME ON THE GENTENT CLAMPS SECURE GENTENT CANOPY OVER GENTENT FRAME SELECT AND INSTALL ELECTRICAL APRON INSTALL THE GTU (OPTIONAL WHERE NEEDED) IMPORTANT GENTENT USAGE TIPS CLEAR VINYL ELECTRICAL APRONS GENTENT 20K AND (OPTIONAL) GENTENT 10K OMNI FIT APRON PROPER DOOR SEALING TIP GENTENT ACCESSORIES AND SPARE PARTS CATALOG REGISTER YOUR PURCHASE ACTIVATE YOUR WARRANTY Getting Help is Easy Need help for your generator or want us to double check your installation? your questions or pics to support@gentent.com, and include the make and model of your generator. Product Registration If you purchased from your product is already registered. Otherwise, please visit or mail the completed page at the back of this manual, so that we can establish your purchase date and keep you informed of any periodic updates. Installation Addendums Installation addendums exist for certain generators. Please review to see if there is one for your generator. Currently they exist for the Generac LP5500, XG10000/XP10000, and GP15000/GP17500 and certain Ridgid generators.

3 Page: 3 of 18 IMPORTANT PRODUCT SAFETY Please review these important safety warnings, cautions and notes: WARNING Always shut generator off before any fueling or maintenance procedures. WARNING Never position the refueling door on the same side of the generator as the exhaust muffler. Spilled gasoline can result in fire. WARNING Never block or cover the generator exhaust muffler in any way. GenTent canopy must be installed above generator exhaust muffler. Install GenTent Electrical aprons such that they cannot block exhaust in any way. Keep the GenTent canopy at least 6 inches away from direct contact with the exhaust. WARNING Always install included washer between the knob and the clamp base AND between the bolt head and clamp base. Tightening the knob without using the washer VOIDS the WARRANTY as it risks breakage. WARNING Never use the GenTent on a generator whose muffler is openly exposed at the top of the generator. These generators are disqualified and VOID the WARRANTY of the GenTent. WARNING Never use the GenTent on a generator in a moving vehicle. CAUTION Over tightening clamps should be avoided. Two turns after the knob seats to the washer/clamp is enough. If you notice the mouth of the clamp pulling away from the frame, the clamping strength has been reduced and the knob should be loosened. CAUTION Always grasp fiberglass rods firmly during installation to avoid the whipping motion that can occur when a bent fiberglass rod is mistakenly released. CAUTION Avoid using your portable generator in hurricane force winds above 70mph. NOTE Should generator handle cause significant stretching of the elastic straps when extended, it is advisable to release the elastics straps on the handle side of the generator before extending generator handles. NOTE Should GenTent cover block pull starter, it is advisable to release the elastic straps on the pull starter side and temporarily move GenTent canopy out of the way. NOTE When using GenTent during snow storms, it is recommended to periodically brush away any accumulation that blocks the top vent.

4 Page: 4 of 18 Limited Warranty What is Covered This warranty covers any defects in materials or workmanship of the GenTent Safety Canopy under normal use in winds up to seventy mph and snow loads up to eighteen inches, with the exceptions stated below. Coverage Period The warranty runs from the date on your GenTent product receipt. Warranty period for hardware components is three (3) years. Warranty period for STORMBRACER EXTREME canopies (or USA Flag on logo) is three (3) years. Warranty period for Stormbracer canopies without the Extreme version isignia is one (1) year. What is not Covered This warranty does not cover issues resulting from improper installation or issues resulting from not adhering to the Warnings and Cautions as stated in this GenTent Product Installation and Safety Manual. This warranty does not cover fading or discoloration caused by exposure to sunlight or chemicals, slight fabric color mismatches, or deterioration due to exposure to chemicals. This warranty does not cover abuse, misuse, or neglect including, but not limited to, lost parts, over tightening clamps, blocking a running portable generator exhaust with parts of the GenTent, or rips, tears or breaks due to sharp and/or heavy and/or falling objects or animals. This warranty does not cover issues arising because of modifications made to your portable generator or to the GenTent that have not been specified by the manufacturer. GenTent products or components returned without an RMA and proof of purchase are not covered (see How to Get Service). Also, consequential and incidental damages are not recoverable under this warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. What GenTent Safety Canopies LLC Will Do GenTent Safety Canopies, LLC will repair any GenTent canopy or replace any GenTent frame or clamp component that proves to be defective in materials or workmanship during the term of this Warranty. In the event repair of a GenTent canopy is not possible, GenTent Safety Canopies will replace your GenTent canopy with a new GenTent canopy of similar composition and price. How to Get Service Contact GenTent Safety Canopies LLC by ing service@gentent.com, calling or writing us at the address below to discuss your Warranty concern and obtain a RMA (return materials authorization). You must provide a copy of the original receipt or packing slip that you received as part of your purchase. GenTent Safety Canopies, LLC Attn: Customer Warranty Service 44 Gile Rd Nottingham, NH How State Law Applies This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

5 Page: 5 of 18 Package Contents This package includes everything required to install the GenTent model that you have purchased on your portable generator: GenTent 10K GenTent 20K 1 Product and Safety Manual 1 GenTent 10k Canopy 1 Short side opaque Electrical apron 1 Long side opaque Electrical apron 1 Central Connector with vent rod 4 40 Fiberglass frame rods 4 GenTent Clamp main body 4 GenTent Clamp telescoping rod 4 Self-locking GenTent Clamp knobs 8 GenTent clamp washers 4 Stainless steel ¼-20 x 1.25 carriage bolts 4 GenTent Clamp rubber sleeves 4 Telescoping rod set clips 1 Product and Safety Manual 1 GenTent 20k Canopy 1 Short side Electrical apron stacking clear vinyl 1 Long side Electrical apron stacking clear vinyl 1 Central Connector with vent rod 4 44 Fiberglass frame rods 4 GenTent Clamp main body 4 GenTent Clamp telescoping rod 4 Self-locking GenTent Clamp knobs 8 GenTent clamp washers 4 Stainless steel ¼-20 x 1.25 carriage bolts 4 Telescoping rod set clips 4 GenTent Clamp rubber sleeves Optional Accessories and Adapter Kits (See Page 14) Your kit may include an optional frame extender or frame adaptation kit. Please see separate instructions for these items. Frame extension or adaptation, if required, must be completed prior to installing the GenTent.

6 Page: 6 of 18 Installation Overview The GenTent installs in three easy steps***: Clamp it: Install 4 clamps and set the telescoping rod length. Frame it: Install frame rod to the center connector, then into the correct hole in the telescoping rod and repeat. Cover it: Slide the GenTent canopy over the frame and secure by sliding the elastic straps over and behind the clamp telescoping rod. Once the GenTent is installed, it can be left in place during generator storage or easily removed and stored separately. Should you wish to store the generator with the GenTent attached, we recommend releasing the elastic straps to keep them fresh and ready. ***Note: In some cases frame adaptation is required to create a mounting point for the GenTent clamps. Should your kit include frame adapter(s) please follow the instructions page 14 or separately in your package. Frame adaptation is required when: One Corner needs to be adapted when: - A muffler heat shield or other panel is connected to a frame member that otherwise blocks the GenTent clamp from attaching directly to the proper location. Four Corners need to be adapted when: - The portable generator uses a square tubular frame that must be adapted to the round openings of the GenTent clamps. - The portable generator is a very small frame and requires length and width extension (see Clamp Adjustment tables on page 9) Special Frame Configurations Exist: - When the frame does not provide 4 cornered mounting points such as: Note: In any of these special cases a special frame kit and addendum is included in the respective special product bundle (or will need to be ordered separately) o Ridgid RD series generators (except certain 5700W models) which do not have vertical frame members at the front of the generator o Generac GP15000/GP17500 where the fixed handles block the canopy o Certain other odd shaped frames such as the Briggs and Troy- Bilt 01925

7 Page: 7 of 18 Install GenTent Clamps on Generator Frame 1) Determine whether the Rubber Sleeves are required The GenTent Clamp kit includes 4 rubber sleeve adapters meant for use on frame diameters less than 1.5. If you do not know the diameter of your frame, wrap a slit of paper or string around the frame tube, marking where the beginning and end cross. Lay it on the tool to determine if the rubber sleeves should be used. 2) Assemble Clamp parts Note: Be sure to use washers between the knob and clamp body as well as between the bolt and the clamp body. - Slide telescoping rods into clamp bodies. - Install set pins through clamp bodies and telescoping rods - Install washer on bolt and bolt through one end and into clamp - Loosely install washer and self-locking knob onto carriage bolt 3) Install Clamp on Generator Frame (or Frame Adapter) Position the top edge for the clamp at the lower of these two locations: (1) 9 below where the gas tank meets the frame, or (2) Directly below the electrical panel Note: The goal is for the bottom of the main canopy to be at or slightly below where the tank connects to the frame; this way water can t get on the tank and trickle toward the outlets. Further, the top of the clamp should be located under the bottom of the lowest electrical outlet -- the electrical protection skirt will cover at least to the top of the clamp. -For frames less than 1.5 : slide rubber sleeve over frame member. Preferably position the rubber sleeve opening to face toward clamp opening (fig. 3-A). Tip: For 1.5 frames, use the sticky back rubber pads that may have come in your kit, or contact GenTent for a set of rubber pads. Alternatively cut any rubber 1/8 or less in thickness to fit between the frame and clamp ( such as an old bicycle tire tube).

8 Page: 8 of 18 - Push clamp opening straight onto frame (fig. 3-A). The clamp will pop over the frame. If rubber sleeve used, slide clamp up and over (fig. 3-B). Do not over extend the mouth of the clamp! - Position clamp diagonally from sides of the generator frame (fig. 3-C); - Tighten knob, centered on washer until clamp is firmly in place. This usually requires only 2 full turns once the knob/washer seat to the clamp body. Clamp strength is reduced by over-tightening as the clamp mouth pulls away from the frame. - Repeat procedure on remaining three sides; position clamps at the same height. Fig. 3-A Fig. 3-B Fig. 3-C

9 GenTent 20k Clamp Easy Adjustment Guide Frame Length (inches) F * r 26 4* 4* a * 4* 4* m 25 4* 4* 4* 4* e * 4* 4* 4* * 4* 4* 4* 4* W * 4* 4* 4* 4* 4* i 23 4* 4* 4* 4* 4* 4* 4* d * 4* 4* 4* 4* 4* 4* t 22 4* 4* 4* 4* 4* 4* 4* 4* h * 4* 4* 4* 4* 4* 4* 4* 4* * 4* 4* 4* 4* 4* 4* 4* 4* Page: 9 of 18

10 Page: 10 of 18 4) Set Rod Adjustment Pin - Reference Appropriate Easy Adjustment Guide (previous page) for GenTent 10k or GenTent 20k - Measure length and width of generator frame to the outside of the frame members - Find corresponding pin setting number in Easy Adjustment Guide - Set the telescoping rod location (Fig. 4-A and 4-B) based on the setting number from the Easy Adjustment Guide and install set pin to secure Fig. 4-A Fig. 4-B Settings Notes: (a) Rod location for setting 0 and 1 are the same (Fig. 4-A). Use the inside frame rod hole for setting 0 and the outside frame rod hole for settings 1-4. (b) SMALL indicates that the use of a Four corner frame extension kit is required. The GenTent will be too loose on the frame otherwise.

11 Page: 11 of 18 Install GenTent Frame on the GenTent Clamps - Position Central Connector with centered vent rod up (fig. 5-A). - Position Central Connector so that short side and long side align with generator short and long sides, respectively. Note: Each frame rod goes into the Central Connector hole first and then into the corresponding clamp hole - Insert a fiberglass frame rod into Central Connector hole until it stops (fig. 5-A) - Insert other end of the fiberglass rod fully into the correct clamp hole of the corresponding clamp (Fig. 5-B) - Insert second fiberglass rod fully into the opposite hole in the Central Connector - Grasping the end of this fiberglass rod, bend toward the opposite side clamp and insert fully into the correct hole (fig. 5-B) CAUTION: Hold rod with two hands as shown; Fiberglass rod will be under tension, do not release! - Repeat for final two fiberglass rods (fig. 5-C). - Recheck clamps; they should be firmly in place and may exhibit a slight upward lean. Fig. 5-A Fig. 5-B Fig. 5-C

12 Page: 12 of 18 Secure GenTent Canopy over GenTent Frame - Position GenTent canopy over the frame. Be certain that the fueling door is not on the same side as the generator exhaust (fig. 6-A). - Slide GenTent canopy over the frame so that all four corners are generally equal and level (fig. 6-A). - Center GenTent canopy such that Vent Rod is centered under the top cap (fig. 6-A). - Slide one corner elastic over the corresponding clamp telescoping rod and set it under the clamp body, behind the set pin (fig. 6-B). - Repeat on opposite corner, then on the remaining two corners. Recheck and adjust canopy if necessary. - Adjust clamps left to right as necessary so that Cover seams generally match the frame rods. - Recheck clamps; they should be firmly in place and may exhibit a slight upward lean. Fig. 6-A Fig. 6-B

13 Page: 13 of 18 Select and Install Electrical apron - If your electrical outlets are on the short side of the generator, select the short Electrical apron; otherwise select the long Electrical apron. Only use one skirt! - Flip the canopy over flap up from corner to corner on the side that is over the electrical outlets (fig. 6-C). - The left and ride sides of the Electrical apron are angled upward slightly as compared to the main body of the skirt. The angle starts about 6 inches from either side and this corresponds to the respective corner of the GenTent. Press either corner on first (fig. 6-C), then wrap the 6-inch section onto the adjacent side of the electrical panel and press firmly. Now press the main skirt body over the electrical panel to the other corner, and then wrap that edge around the adjacent side and press firmly in place. - Flip the over flap down and over the Electrical apron (fig. 6-D). Fig. 6-C Fig. 6-D Note: The intent of the Electrical apron is to cover the electrical outlets in the front and about 6 around the adjacent sides. Do not cover other parts of your generator with the Electrical aprons, especially the exhaust area!

14 Page: 14 of 18 Adapt the Frame (if needed) Your portable generator model may have a square tubular frame, be very small and require some lengthening and/or widening, or have a muffler heat shield or other panel connected to one of the frame members that blocks the GenTent clamp from directly connecting to the frame on one corner. In the case that your portable generator is in this category, or if you purchased one of our universal fit GenTent bundles, there will be between one (1) and four (4) GTU Frame Adapters in your package. Each GTU Frame Adapter includes: GTU adapter this is a black molded part that incorporates a squared angle with a round mounting area. 2 #12 Sheet metal screws Note: You will need a drill and a 5/32 drill bit The GTU installs in these easy steps for each GTU Adapter required: Locate and mark: where the GTU will be installed. Drill: Two holes for mounting the GTU. Mount: Screw the GTU in place Once the GTUs are installed, follow the main GenTent installation instructions from page 6. Locate the GTU on the generator frame: The top screw hole of the GTU should be located either: (a) 9 below where the gas tank meets the frame, OR (b) 1/2 above the bottom of the lowest electrical outlet on the electrical panel, Whichever location is lower on the generator frame. The bottom edge of the main canopy should to be at or slightly below where the tank connects to the frame so water can t get on the tank and trickle toward the outlets. The electrical protection skirt will cover to the top of the clamp which should be below the lowest electrical outlet. Zip ties can be used for temporary mounting to find the correct location.

15 Page: 15 of 18 Fig. 8-A Fig. 8-B Fig. 8-C Fig. 8-D Mark the GTU screw location on the generator frame: - Position GTU against the frame member at the outside corner at the measured location (Fig. 8-A and 8-D). - Using the drill and the 5/32 drill bit or sheet metal screw, scratch a mark on the generator frame through the screw holes on the GTU (top and bottom). Note: drill one screw hole on the right side of the GTU and the other on the left side. Select top left/bottom right or top right/bottom left based on which gives the most clearance for the drill and screw operations. Drill and Mount GTU: - Drill two pilot holes, using the 5/32 drill bit, at the locations previously scratched/marked (Fig. A) - Using 5/16 nut driver, or flat blade screwdriver (nut driver recommended), screw GTU to frame (Fig. B) GenTent Clamp Installation notes: - Install a GenTent rubber adapter onto the GTU before installing the GenTent clamp (Fig. 8-E) - Set the GenTent clamp rod one step in versus other clamps that are attached directly to the generator frame (for example, if your normal clamp pin setting is 2, set the clamp pin on the GTU side to 1) - See page 9 for clamp pin setting adjustment guide Fig. 8-E Fig. 8-F

16 Page: 16 of 18 Important GenTent Usage Tips Clear Vinyl Electrical aprons GenTent 20k and (Optional) GenTent 10k Omni Fit Apron The clear vinyl skirt for the GenTent 10k and the GenTent 20k Electrical aprons provide a window to gauges during operation and can be stacked together for double height (Fig. 9-A) by connecting the top of one skirt to the bottom of another skirt. Use this as needed for the skirts to completely cover the electrical outlets. Note: The intent of the Electrical apron is to cover the electrical outlets in the front and about 6 around the adjacent sides. Do not cover the exhaust area! The GenTent 10k Omniskirt is the length of the long Electrical apron and fits either the long side (with 6 inch wrap) or short side (with longer wraparound). When used on a short side, the Omniskirt can be centered (leaving 12 wrap on each side) or offset (6 wrap on one side and 24 wrap on the other). This particularly useful for smaller generators where the GenTent has a deep overhang. Starting with 6 from the skirt edge, press the skirt to the corner (fig. 6-C), then wrap the 6 inch section onto the adjacent side of the electrical panel and press firmly. Now press the main skirt body over the electrical panel to the other corner, and then wrap that edge around the adjacent side and press firmly Fig. 9-A into place. Proper Door Sealing Tip The GenTent StormBracer door wraps around the adjacent sides of the GenTent much like the skirts, forming a brace against storms. Each time you close the door, the Velcro must be wrapped around the side and pressed firmly back in place. If this is not done, holes may exist between the pieces of Velcro which can allow water to seep in. In practice, the best way to achieve this is to close the door, then follow this procedure: - Align the door properly so that the side Velcro and lower Velcro are aligned as closely as possible and are touching - Then starting at the top corner of the door pinch canopy around the frame rods and slide your hand to the bottom while pinching. - Repeat on the other side - Check the door sides to see if you can see any gaps in the Velcro sealing. Should there be any gaps, repeat the pinching procedure. Note: Pull the door down and connect the bottom Velcro first, then use the pinch & slide technique above to secure the sides. The bottom edge should cover the under-flap stitching!

17 Page: 17 of 18 GenTent Accessories and Spare Parts Catalog GenTent accessories are available at Spare parts are available at Here is a short list of what we offer:

18 Register Your Purchase Activate Your Warranty Note: If you purchased directly at GenTent.Com, your purchase is already registered and completing this registration document is not required! Page: 18 of 18 Complete your registration online at or fill out this card and mail to: GenTent Safety Canopies Attn: Product Registration 44 Gile Rd Nottingham, NH Your Information: Name: Address: Address: City: State/Province: Country: Zip/Postal Code: Phone Number: Purchase Information: GenTent 10k GenTent 20k GenTent Purchase Date: / / (mm/dd/yyyy) Where did your purchase the GenTent? Generator Make: Generator Model: In addition to activating your product warranty, registering allows us to keep in contact with you from time to time with important product updates, generator safety tips and special offerings for registered customers. Please note we never share your contact information.