DUCATI MONSTER 696/796 CARTRIDGE KIT
|
|
- Garry Kennedy
- 5 years ago
- Views:
Transcription
1 DUCATI MONSTER 696/796 CARTRIDGE KIT
2 INSTALLATION OF THE KYB CARTRIDGE KIT Available for models Ducati Monster 696 and 796 from 2011 to 2014 This manual concerns the installation of the aftermarket KYB suspension Cartridge Kit for the Ducati Monster models 696 and 796 with the KYB stock forks. It describes the replacement of the cartridge in the left and right fork. Product code: MONSTER-CARTRIDGE-1 Duration: ± 60 minutes An additional instructional video can be found on this kit s webshop page. For additional information about the installation or adjustment of this KYB Cartridge Kit, please contact the nearest authorized KYB dealer. SAFETY Always use the correct tools. Follow every step as described in the manual. KYB, Technical Touch and/or their affiliated companies cannot be held liable for improper installation and/or use of this KYB cartridge kit. 2
3 CONTENTS OF THIS CARTRIDGE KIT Before installation, check the completeness of the kit. 8 RIGHT LEG LEFT LEG 2 1. Cartridge 2. Spring 3. Preload push rod 4. Stroke limiter shaft 5. Top out spring 6. Inner tube cap 7. Bump stop 8. Counter nut 9. Top cap 3
4 SPECIAL TOOLS Top Cap Socket T-bar Standard Inner Cap T-bar Aftermarket Inner Cap Consumables 700 ml W10 fork oil 270 strength Loctite or similar thread locker 4
5 INSTRUCTIONS Removal of the cartridge from the right fork leg Note: Make sure you don t damage the outer tube with the vise, use a soft material to clamp it in. 1. Clamp the outer tube in a vise where the lower triple clamp clamps on the tube. 2. Unscrew the top cap. 3. Drain the oil from the fork leg. 5
6 Removal of the cartridge from the right fork leg 4. Clamp the fork leg with the axle bracket in the vise. 5. Push in the cartridge on the top cap side. 6. Remove the cartridge bolt in the axle bracket. Note: the cartridge may rotate with the bolt. An impact wrench may be needed to loosen the bolt. 7. Take out the cartridge. 6
7 Installation of the KYB cartridge in the right fork leg 1. Place the KYB cartridge in the fork leg. 2. Tighten the bolt fixing the cartridge to the axle bracket. Tighten to 35Nm. 3. Fill the fork leg with 400ml W10 fork oil. 4. Tighten the top cap using the Top Cap Socket. Tighten to 35Nm. 7
8 Installation of the KYB cartridge in the right fork leg Caution: Make sure you don t overtighten the rebound adjuster screw. When the resistance of the screw increases, you need to return it to the last click. 5. Turn the rebound adjuster screw fully in (direction H). 6. Push in the fork leg several times to bleed the air from the cartridge. An equal hydraulic resistance (damping) over the full stroke can be felt when the cartridge is completey filled with oil. 7. Unscrew the rebound adjuster 15 clicks (direction S ). 8
9 Removal of the stock stroke limiter from the left fork leg Note: Make sure you don t damage the outer tube with the vise, use a soft material to clamp it in. 1. Clamp the outer tube in a vise where the lower triple clamp clamps on the tube. 2. Unscrew the top cap. 3. Drain the oil from the fork leg. 9
10 Removal of the stock stroke limiter from the left fork leg Caution! If you hold the fork leg by the outer tube, the inner tube will slide out much further with the bump stop removed. 4. Clamp in the fork leg on the axle bracket. 5. Loosen the bump stop. 6. Remove the top cap. 7. Remove the bump stop. 8. Heat up the inner tube cap to break the thread locker glue. 9. Unscrew the inner tube cap using the T-bar Standard Inner Cap. 10
11 Removal of the stock stroke limiter from the left fork leg 10. Remove the stroke limiter. 11. Remove the stock spring. 11
12 Installation of the KYB stroke limiter and spring in the left fork leg Caution: The preload push rod is not fixed to the stroke limiter and can slide out while unpacking. 1. Remove the top cap from the KYB stroke limiter using the Top Cap Socket. 2. Remove the lock nut and rubber bump stop from the stroke limiter. 3. Place the KYB spring into the fork leg. 4. Place the KYB stroke limiter with the preload push rod into the fork leg. 5. Put Loctite 270 strength onto the KYB inner tube cap. 6. Screw the inner tube cap into the inner tube using the T-bar Aftermarket Inner Cap. 12
13 Installation of the KYB stroke limiter and spring in the left fork leg 7. Slide the KYB bump stop onto the stroke limiter shaft. 8. Screw the lock nut onto the stroke limiter. 9. Install the KYB top cap using the Top Cap Socket. 10. Screw the lock nut to the top cap, tighten to 30Nm. 10. Fill the fork leg with 300ml W10 fork oil. 11. Install the top cap using the Top Cap Socket. Tighten to 35Nm. 12. Screw out (counter clockwise) the preload adjuster until max out, screw in (clockwise) the preload adjuster 5 full revolutions to set it halfway. 13
14 ADJUSTMENT GUIDELINES Adjustment options Preload The spring preload adjuster has an adjustment range of 10mm. Every full revolution increases/decreases 1mm of preload. The spring preload adjuster is located on the top cap of the left fork leg. Rebound The rebound adjuster (tension) completely turned in (clockwise), is position 0 (maximum damping/ slowest movement). The rebound adjuster has a range of clicks, the adjusted position is always counted from the fully turned in position. It is recommended to make steps of 2 or 3 clicks in case you want to change the rebound damping, fine-tuning the rebound can be done per 1 click. The rebound adjuster is located on the top cap of the right fork. Caution: Make sure you don t overtighten the rebound adjuster screw. When the resistance of the screw increases, you need to return it to the last click. Oil level The size of the air chamber can be adjusted by increasing or decreasing the oil level in the fork legs. Adding oil will make the suspension more progressive. Changes in the oil level should be done in steps of 10ml. 14
15 ADJUSTMENT GUIDELINES Adjustment guide Note that for suspension setup, there is no setup that will work for everybody and for every condition. Damping characteristics will always be a compromise of different settings. Preload: Preload affects the ride height and available suspension travel under braking and accelerating. A floating feeling on the front wheel indicates too much preload. In case the front end feels low, the preload can be increased. Generally a more sporty riding style requires an increased preload. Rebound: The rebound damping controls how fast your fork extends after being compressed. Too much rebound will keep the suspension compressed after absorbing a bump, not enough rebound will make the front feel loose. A correct rebound setting will provide more feedback and traction. Oil level The air chamber size can be adjusted with the oil level. When the suspension bottoms out, the oil level has to be increased. A too hard suspension can be adjusted by lowering the oil level. Changes in the oil level should be done in steps of 10ml. 15
16 Technical Touch BVBA EUROPE IZ Kristalpark Ondernemersstraat Lommel Belgium info@technical-touch.com tel: fax: Technical Touch USA AMERICA / AUSTRALIA 1500 S Miliken Avenue Suite E CA Ontario United States of America info@technicaltouchusa.com tel: fax:
DUCATI SCRAMBLER REAR SHOCK INSTALLATION
DUCATI SCRAMBLER REAR SHOCK INSTALLATION INSTALLATION OF THE KYB REAR SHOCK Available for Ducati Scrambler models: Café Racer, Sixty2, Icon, Classic and Full Throttle This manual concerns the installation
More informationOwners manual. Öhlins Superbike front fork FG 170
Owners manual Öhlins Superbike front fork FG 0 Including: Setting up your fork Changing springs and seals Service the fork Trouble shooting Technical info Spare parts & tools Öhlins super bike front fork
More informationSachs 48mm Closed Cartridge fork Service Manual
Sachs 48mm Closed Cartridge fork Service Manual 1 Fork seal driver 2 Special soft jaws 3 Fork cap wrench 4 Rebound rod holding tool 5 Compression assembly holding tool 6 Retaining clip tool Special Tools
More informationZ125 Front Fork Upgrade kits. Installation SOP
Z125 Front Fork Upgrade kits Installation SOP Tools a. Loctite243 or Loctite2701 (Thread Locker) b. Loctite7649 (Activator) c. 33mm Hex Socket d. 17mm Hex Socket e. Shaft Clamping Tool (12mm) f. Shaft
More informationAfter Installing an Öhlins Shock Absorber/Front Fork
Checkpoint Öhlins After Installing an Öhlins Shock Absorber/Front Fork Note! All motorcycles are designed with a suspension geometry that includes height and fork angle. Changing components (for example
More informationG2-R COMPRESSION GOLD VALVE INSTALLATION DIRT 32x KYB AIR SPRING OPEN CHAMBER FORK
1501 Pomona Rd, Corona, CA 92880 951.279.6655 racetech.com G2-R COMPRESSION GOLD VALVE INSTALLATION DIRT 32x8 2015 KYB AIR SPRING OPEN CHAMBER FORK FK code 2 part LS FMGV 320802G
More informationFKR 105. Mounting Instructions. Cartridge kit for Kawasaki ZX-10R
Kit Contents Description Part No Pcs Cartridge kit FKR 105 1 O-ring x 008-50 O-ring 0x.5 00576-0 Main spring 9.5 N/mm 07-95 Main spring 10.0 N/mm 07-10 Main spring 10.5 N/mm 07-05 Sticker 00191- Sticker
More informationFITTING INSTRUCTIONS YAMAHA YZF-R3
FITTING INSTRUCTIONS YAMAHA YZF-R3 120-015-270-005 20/07/2017 ISSUE 1 2 IMPORTANT NOTES KEY NB NOTE! CAUTION! WARNING! NB NB NB The front forks are a very important part of the motorcycle and will affect
More informationFORK COMPRESSION AND REBOUND GOLD VALVE INSTALLATION - DIRT 35C/30R SFF
1501 Pomona Rd, Corona, CA 92880 951.279.6655 racetech.com FORK COMPRESSION AND REBOUND GOLD VALVE INSTALLATION - DIRT 35C/30R SFF FK code 2 part LS FMGV 3521C P Thede 12.3.15 7 pgs
More informationFORK G2-R COMPRESSION GOLD VALVE INSTALLATION - DIRT 37
1501 Pomona Rd, Corona, CA 92880 951.279.6655 fax 951.279.7171 racetech.com FORK G2-R COMPRESSION GOLD VALVE INSTALLATION - DIRT 37 FK code FMGV 3720G P Thede 12.3.15 TOOLS REQUIRED:
More informationTUNING GUIDE. ridefox.com
TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses under
More informationTUNING GUIDE. ridefox.com
TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses under
More informationOwners Manual Öhlins road & track front fork FG 43 Including:
Owners Manual Öhlins road & track front fork FG 43 Including: Safety Adjusters Setting up your fork Changing springs Oil level adjustment Technical information Inspection & maintenance Service Tools 1
More informationTUNING GUIDE. ridefox.com
TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses under
More informationÖhlins Front Fork Road & Track FG 43. Owner s Manual
Öhlins Front Fork Road & Track FG 43 Owner s Manual Öhlins Headquarters Upplands Väsby, Sweden Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time
More informationSpring manual V3.1 ENGLISH
Spring manual V3.1 ENGLISH HYPERPRO TOOLS, used in this manual: Tool Description Part no. A, B, C Cartridge fork spring removal tool kit HP-T01 D Big Piston Fork end cap socket 45mm HP-T102 E Big Piston
More informationFORK GOLD VALVE INSTALLATION STREET / ROAD RACE 37mm BPF SFF
1501 Pomona Rd, Corona, CA 92880 951.279.6655 racetech.com FORK GOLD VALVE INSTALLATION STREET / ROAD RACE 37mm BPF SFF FK code FMGV S3702C P Thede 2.27.15 5 pgs TOOLS REQUIRED:
More informationTUNING GUIDE. ridefox.com
TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses under
More informationÖhlins Front Fork for. Motocross and Enduro. Owner s Manual
Öhlins Front Fork for Motocross and Enduro Owner s Manual Safety Precautions The front fork is a very important part of the vehicle and will therefore affect the stability. Read and make sure that you
More informationFKS 213. Mounting Instructions. Cartridge kit for Harley-Davidson Sportster Forty-Eight
Kit Contents Description Part No Pcs Cartridge kit FKS 213 1 Preload tube 0160-9 2 Guide ring 21808-01 2 O-ring 0076-02 2 Top out spring 21801-02 2 Sticker set Öhlins 1 Owner s manual 07289-01 1 Please
More informationÖhlins Front Fork Superbike FGR 900. Owner s Manual
Öhlins Front Fork Superbike FGR 900 Owner s Manual Introduction Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time pursuing his favourite sport:
More informationÖhlins Front Fork Kit for. Motocross and Enduro. Owner s Manual - General Mounting Instructions
Öhlins Front Fork Kit for Motocross and Enduro Owner s Manual - General Mounting Instructions Safety Precautions Safety Symbols The front fork is a very important part of the vehicle and will therefore
More informationOWNERS MANUAL. LINK & PDS Trax shock absorber.
OWNERS MANUAL LINK & PDS Trax shock absorber Introduction: Congratulations on your purchase of the WP Trax Off-road shock absorber. The WP Trax shock absorber has a unique system, which provides better
More informationShock Absorber for MC Road & Track TTX GP. Owner s Manual
Shock Absorber for MC Road & Track TTX GP Owner s Manual Öhlins Headquarters Upplands Väsby, Sweden Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare
More informationFKR 104. Mounting Instructions. Cartridge kit for BMW S1000RR, BMW HP4
Kit Contents Description Part No Pcs Cartridge kit FKR 10 1 O-ring (.0x3.53) 0038-26 2 O-ring (23.52x1.78) 0038-02 2 Plug 21652-06 2 Main spring 9.5 N/mm 07-95 2 Main spring 10.0 N/mm 07-10 2 Main spring
More informationFDK 106. Fork Damping Kit for Kawasaki Z125 Fork Damping Kit. Mounting Instructions. Note!
Kit Contents Description Part No Pcs Screw M8x25 15209-01 2 Washer 8/13/1 copper 60048-01 2 Top cap 60005-25 2 O-ring 25.8x3.53 00438-29 2 Comp. damping rod FDK 106-C 1 Reb. damping rod FDK 106-R 1 Spring,Fr.fork
More informationTOO TECH RACING SET-UP INSTRUCTIONS (For Non Twin Chamber Showa & KYB)
TOO TECH RACING SET-UP INSTRUCTIONS (For Non Twin Chamber Showa & KYB) STEP 1: Measure suspension "Race Sag". (Most important adjustment there is) First: Put the bike on a center stand and release the
More informationOWNER`S MANUAL 50SXS/65SXS COMPETITION
OWNER`S MANUAL 50SXS/65SXS COMPETITION SHOCK ABSORBER Introduction: Congratulations on your purchase of the WP Off-road shock absorber. The WP shock absorber is a unique product, which provides better
More informationFGK 224. Mounting Instructions. Front Fork Kit for Ducati 1199 Panigale. Warning! Warning! Note!
Before installing this product, check the contents of the kit. If anything is missing, please contact an Öhlins dealer. Kit Contents Part No. Pcs. Front fork kit FGK224 1 Plug 21652-03 2 O-ring 00438-23
More informationFORK GOLD VALVE INSTALLATION G2-R DIRT 34 &35mm (2LS)
1501 Pomona Rd, Corona, CA 92880 951.279.6655 fax 951.279.7171 www.racetech.com FK code FORK GOLD VALVE INSTALLATION G2-R DIRT 34 &35mm (2LS) 2 part LS FMGV 3420G, 3520G P Thede 7.6.11
More informationRXF36 Coil. Front Fork. Owner s Manual/ Mounting Instructions
Kit Contents Description Part No Pcs Front Fork RXF36 Coil 1 Before installing this product, read this manual. The front fork is an important part of your bicycle and will affect the stability. Please
More informationOwners manual Competition Shock absorber. WP Suspension Netherlands
Owners manual 4618 Competition Shock absorber WP Suspension Netherlands 1 INTRODUCTION: Congratulations on your purchase of this WP Suspension shock absorber, The shock absorber that won the 2001/2002/2003/2004/2005/2006
More informationOwner's Manual Öhlins motocross front forks 48 MXF 2007
Owner's Manual Öhlins motocross front forks 48 MXF 2007 Including: Setting up your bike Fine-tuning Service the fork Technical info Spare parts General handling set-up 1 2 Safety signals Important information
More informationEZRyde Rear Suspension Adjustment and Tuning Manual
EZRyde Rear Suspension Adjustment and Tuning Manual Track Tension 1. Support the rear of the snowmobile with a track stand or equivalent sturdy stand. 2. Hook a spring scale around a track clip at mid-span:
More informationShock Absorber for MC Road & Track TTX. Owner s Manual
Shock Absorber for MC Road & Track TTX Owner s Manual Öhlins Headquarters Upplands Väsby, Sweden Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time
More informationFORK REBOUND GOLD VALVE INSTALLATION - DIRT WP 4CS
1501 Pomona Rd, Corona, CA 92880 951.279.6655 fax 951.279.7171 racetech.com FORK REBOUND GOLD VALVE INSTALLATION - DIRT WP 4CS FRGV 200603 P Thede 4.17.15 5 pgs TOOLS REQUIRED: In
More informationLefty MAX 140 Travel Management, service. Lefty MAX 140 Travel management, service
Lefty MAX 140 Travel management, service THE FOLLOWING SERVICE SHOULD BE PERFORMED AFTER EVERY 40-80 HOURS OF RIDING, OR AT LEAST ONCE A YEAR. THE INSTRUCTIONS ARE FOR ADVANCED MECHANICS. THEY DO NOT REPLACE
More informationX-Trainer 43mm fork service manual. Beta USA, Inc This work should be performed by a trained motorcycle technician.
X-Trainer 43mm fork service manual Beta USA, Inc. 2016 This work should be performed by a trained motorcycle technician. Table of contents Page Introduction/special tools... 2 Fork exploded view... 3 Legend.
More informationFPK 103. Mounting Instructions. Front Fork Piston Kit for Ducati 848/1098/1198
Before installing this product, check the contents of the kit. If anything is missing, please contact your Öhlins dealer. Kit Contents Pcs Compression Piston Assembly 2 Rebound Piston Assembly 2 Öhlins
More informationFKS 203. Mounting Instructions. Cartridge kit for Yamaha R25 R3 MT-03
Kit Contents Description Part No Pcs Cartridge kit FKS 0 Sticker 009- Sticker 009- Owner s manual 0789-0 Please note that there can be small differences between your product and the images in these instructions.
More informationÖhlins Shock Absorber for MX & Enduro TTX44. Owner s Manual
Öhlins Shock Absorber for MX & Enduro TTX44 Owner s Manual Introduction Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time pursuing his favourite
More informationÖhlins Front Fork Pressurized Cartridge Kit. FKR 100-Series. Owner s Manual
Öhlins Front Fork Pressurized Cartridge Kit FKR 100-Series Owner s Manual Öhlins Headquarters Upplands Väsby, Sweden Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent
More informationRXF34/RXF36. Front Fork. Owner s Manual/ Mounting Instructions
Kit Contents Description Part No Pcs Front Fork RXF34/ RXF36 1 Before installing this product, read this manual. The front fork is an important part of your bicycle and will affect the stability. Please
More informationSTX22Air AM Goldline. Owner s Manual/ Mounting Instructions
Kit Contents Description Part No Pcs Shock absorber STXAir Before installing this product, read this manual. The shock absorber is an important part of your bicycle and will affect the stability. Please
More informationTTX Cartridge Kit for KTM EXC/EXC-F/XC-W & Husqvarna FE/TE/TX (WP XPlor 48) FGKT Mounting Instructions
No springs included in this kit. Use appropriate Öhlins Front Fork springs, part no. 08765-XX. See the Spring guide in this folder or contact Öhlins for advice. Please note that this image is a general
More informationMaverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.2 SHOCK SERVICE MANUAL
Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.2 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.2 rear shock is an oil damped
More informationFGK 204. Mounting Instructions. Front Fork Kit for Honda CBR600RR. Warning! Warning! Note!
Before installing this product, check the contents of the kit. If anything is missing, please contact an Öhlins dealer. Kit Contents Part No. Pcs. Front fork kit FGK204 1 Sticker set Öhlins 1 Owners manual
More informationMULTISTRADA 1200 S (ALL COUNTRY VERSIONS)
Date: 13/09/2011 Subject: Models: FRONT END KNOCK ON OHLINS FORKS MULTISTRADA 1200 S (ALL COUNTRY VERSIONS) Dear Dealer, We hereby inform you about the technical solution to fix the above-mentioned fault;
More informationRXF34/RXF36. Front Fork. Owner s Manual/ Mounting Instructions
Kit Contents Description Part No Pcs RXF34 29 Air TTX22 FG341x 1512 1 120/140/160 mm RXF36 29 Air TTX22 FG361x 171x 1 120/140/150/160 mm RXF36 29 Air STX22 FG361x 1731 1 150/160 mm RXF36 27.5 Air TTX22
More informationFGK 212. Mounting Instructions. Front Fork Kit for BMW S1000RR and HP4 Racing. Warning! Warning! Note!
Before installing this product, check the contents of the kit. If anything is missing, please contact an Öhlins dealer. Kit Contents Part No. Pcs. Front fork kit FGK212 1 Öhlins Sticker (60x23) white 00191-32
More informationFGR 178. Pressurized Front Fork Kit for Honda CBR1000RR SP. Mounting Instructions
Kit Contents Description Part No Pcs Front Fork Kit FGR178 1 Sticker Tech. Inside wh 00191-32 2 Sticker Tech. Inside bl 00191-33 2 Shim 00520-32 2 Spring 10,5N/mm 04744-05 2 Spring 10 N/mm 04744-10 2 Spring
More informationFGGG 992. Owner s Manual - Mounting Instructions. Öhlins Front Fork Kit for Gas Gas EC 300. Note! Warning!
Before installing this product, check the contents of the kit. If anything is missing, please contact your Öhlins dealer. Kit Contents Part No Pcs Front Fork kit FGGG 992 1 O-ring 00338-10 2 O-ring 00438-97
More informationFGBA TTX CArtridge Kit for Beta RR 2T/RR 4T. Mounting Instructions
No springs included in this kit. Use appropriate Öhlins Front Fork springs, part no. 08762-XX. See the Spring guide in this folder or contact Öhlins for advice. Please note that this image is a general
More informationSUSPENSION SETUP GUIDE
For your Pivot suspension equipped bike to pedal and descend at its best, it is important to tune the suspension properly. Use this guide to familiarize yourself with the Pivot suspension setup procedures
More informationfkc 102 Mounting Instructions Cartridge kit for Harley-Davidson Touring FLHx/ FLTx 2014-
Kit Contents Description Part No Pcs Cartridge kit FKC102 1 Sticker 01185-04 2 Owner s manual 07288-01 1 Guide ring 21808-01 2 Please note that there can be small differences between your product and the
More informationTTX Cartridge Kit for KTM SX/SX-F/ XC/XC-F & Husqvarna FC/TC (WP USD AER 48) FGKT 1793/94. Mounting Instructions
No springs included in this kit. Use appropriate Öhlins Front Fork springs, part no. 08765-XX. See the Spring guide in this folder or contact Öhlins for advice. Please note that this image is a general
More informationHayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:
Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching
More informationREAR SHOCK TUNING GUIDE
REAR SHOCK TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses
More informationFLOAT 3 EVOL, R, RC, RC2 FACTORY SERIES AFTERMARKET SHOCK OWNER S MANUAL
FLOAT 3 EVOL, R, RC, RC2 FACTORY SERIES OWNERS MANUAL 2.5 PODIUM-X AFTERMARKET SHOCK OWNER S MANUAL CONTENTS CONGRATULATIONS... 3 CONSUMER SAFETY... 3 UNDERSTANDING THE FLOAT 3 EVOL SERIES... 4 FOX PUMP...
More informationFront Fork Disassembling and Assembling RM-Z250L6. KAYABA Pneumatic Spring Front Fork PSF2
Front Fork Disassembling and Assembling RM-Z250L6 KAYABA Pneumatic Spring Front Fork PSF2 RM-Z250L6 Front Fork Disassembling 1. Release air Release the air pressure by pressing the air valve with a screwdriver.
More informationHayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:
Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching
More informationTable of Contents Safety Warning Information
SUSPENSION FORK INSTRUCTION MANUAL 2 Table of Contents 04... Safety Warning Information 05... Tools Needed 06... Fork Features Overview 07... Crown Race Installation/Steer Tube Cutting 08... Star Nut/Stem
More informationOwner Manual CO3 Cartridge
Owner Manual CO3 Cartridge FAST Suspension CO3 open bath cartridge - Owner Manual Dear customer, Thank you for choosing a FAST Suspension product, which stands for 100% performance. It is fabricated and
More informationFRONT FORK 2.16 GENERAL REMOVAL HOME. 4. See Figure Loosen upper and lower fork clamp pinch fasteners (1, 4).
FRONT FORK.6 GENERAL The XRScg model utilizes a mm fork assembly while all other models have changed to the mm fork assembly. The front fork consists of two telescoping outer tube/inner slider assemblies.
More informationBike Suspension Service
Bike Suspension Service Rear Shocks Service item New After each ride or race Every 30 hours Every 100 hours or annually Set sag Check sag; reset if necessary Set damping adjustments Clean shock exterior
More informationBike Suspension Service
Bike Suspension Service Rear Shocks Service item New After each ride or race Every 30 hours Every 100 hours or annually Set sag Check sag; reset if necessary Set damping adjustments Clean shock exterior
More informationSuper T QR20 INSTRUCTIONS GENERAL RULES
INSTRUCTIONS GENERAL RULES 1. Where specified, assemble and disassemble the shock absorption system using the MARZOCCHI special tools only. 2. On reassembling the suspension system, always use new seals.
More informationFLOAT 3 EVOL RC2 FACTORY SERIES OWNERS MANUAL
FLOAT 3 EVOL RC2 FACTORY SERIES OWNERS MANUAL Contents CONGRATULATIONS... 3 CONSUMER SAFETY... 3 UNDERSTANDING THE FLOAT 3 EVOL RC2... 4 FOX PUMP... 5 OPTIONS... 5 ADJUSTABLE PROGRESSIVE DUAL-STAGE AIR
More informationBasic Information. Öhlins Shock Absorber. Owner s Manual
Basic Information Öhlins Shock Absorber Owner s Manual Introduction Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time pursuing his favourite sport:
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationWorldwide FOX.SHOX ( ) FORK FLOAT 29. Travel 5.1 in./130 mm 5.5 in./140 mm 5.9 in./150 mm Features/Adjustments
Worldwide 1.800.FOX.SHOX (1.800.369.7469) FORK- 2014 34 FLOAT 29 Travel 5.1 in./130 mm 5.5 in./140 mm 5.9 in./150 mm Features/Adjustments Factory FIT CTD w/adj; 130, 140, 150; Kashima Coated or anodized
More informationContents. 1.2 Cartridge maintenance Replacement of the cartridge gasket Piston segment replacement Piston replacement 20
KAYABA SUSPENSION Contents KAYABA SUSPENSIONS General remarks 3 1- YOKE Exploded view 4 1.1 Maintenance of Gaskets and Rings 1.1.1 Disassembly 5 1.1.2 Assembly 8 1.2 Cartridge maintenance 1.2.1 Replacement
More informationMaverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL
Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.0 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.0 rear shock is an oil damped
More informationThank you for purchasing our product
SPINNER is a brand of KOGEE CORP. Model List FORK Aeris /Grind Air/Spinner 300 Air/Spinner 320 Air/Cargo Air Thank you for purchasing our product IN CASE OF MISSING OR BROKEN PARTS, PLEASE CONTACT PLACE
More informationRoad & Track. 30 mm Front Fork Cartridge Kit. Owner s Manual
Road & Track 30 mm Front Fork Cartridge Kit Owner s Manual Introduction Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time pursuing his favourite
More informationThis procedure is best performed on a vehicle lift, however it is possible to install these coilovers using a floor jack and jack stands.
Description: FeatherLight Single Adjustable Corvette Coilovers Part Number: 430-401004-N Application: 2014-2015 Chevrolet Corvette (C7) Note: Some models might be equipped with Magnetic Ride electric adjustable
More informationOwner s Manual. Öhlins Front fork FGRT-series Road & Track
Owner s Manual Öhlins Front fork FGRT-series Road & Track Safety precautions Introduction & design Setting up your front fork Adjustments Changing springs Technical information Inspection and maintenance
More informationREAR SHOCK TUNING GUIDE
REAR SHOCK TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, you will need to attain your proper sag setting. Sag is the amount your suspension compresses under
More information1. Remove the front struts by first disconnecting the ABS wire and brake line(retain hardware) from the factory strut.
Part # 12153111-2005 up Mustang Recommended Tools 2005-up Mustang Front TQ CoilOver Strut Installation Table of contents Page 2... Included components Page 3... Disassembly and Getting Started Page 4...
More informationÖhlins Shock Absorber for Automotive TTX36. Owner s Manual
Öhlins Shock Absorber for Automotive TTX36 Owner s Manual Introduction Öhlins Racing AB - The Story It was the 1970 s, a young man named Kenth Öhlin spent most of his spare time pursuing his favourite
More informationHayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI Tel: Web:
Hayes Performance Systems 5800 W. Donges Bay Rd. Mequon, WI 53092 Tel: 888.686.3472 Email: techsupport@hayesbicycle.com Web: www.hayescomponents.com Hayes Components Europe Dirnismaning 20 a 85748 Garching
More informationShock manual V3.1 ENGLISH
Shock manual V3.1 ENGLISH 2 Shock manual v3.1 INDEX Page Hyperpro Shock Overview 4 Maintenance 5 Rear Shock unit, removal and installation M1 Mono shock (& Telelever front) 6 M2 Twin shock 6 M3 Link system
More informationPS-Mustang-Strut. Strut; In-line or Remote, Single, Double, or Triple Adjustable TECHNICAL MANUAL
PS-Mustang-Strut Strut; In-line or Remote, Single, Double, or Triple Adjustable TECHNICAL MANUAL Main Office 150 Franklin St. P.O. Box 1056 Reading, PA 19603 (610) 375-6180 (610) 375-6190 Fax Introduction
More informationC5/C6 Level 3 Coilover
Part # 11510311-1998-2013 C5/C6 Level 3 CoilOver System Front Components: 11513111 Front Coilovers Recommended Tools Rear Components: 11516111 Rear Coilover Miscellaneous Components: 85000000 Spanner Wrench
More informationFPK 106. Mounting Instructions. Front Fork Piston Kit for Honda CBR600RR
Before installing this product, check the contents of the kit. If anything is missing, please contact your Öhlins dealer. Kit Contents Pcs Compression Piston Assembly 2 Rebound Piston Assembly 2 Öhlins
More informationSTX22Air. Shock absorber for Specialized Enduro, Stumpjumper, Rhyme and Levo. Owner s Manual/ Mounting Instructions
Kit Contents Description Part No Pcs Shock absorber STXAir Before installing this product, read this manual. The shock absorber is an important part of your bicycle and will affect the stability. Please
More informationMXZ RC-P and MXZ R User manual
MXZ RC-P and MXZ R User manual 1 CONGRATULATION Your specialized motorcycle is outfitted with YASUSU shock in suspension system. YASUSU shock absorbers are designed, tested and manufactured by the professional
More informationSUSPENSION SETUP GUIDE
For your Pivot suspension equipped bike to pedal and descend at its best, it is important to tune the suspension properly. Use this guide to familiarize yourself with the Pivot suspension setup procedures
More informationPart # GM F-Body Rear CoilOvers
Part # 1116111-198-00 GM F-Body Rear CoilOvers Recommended Tools 8-0 F-Body TQ Series Rear Coilovers Table of contents Page... Included components Page 3... Hardware List and Getting Started Page 4...
More informationREAR SHOCK TUNING GUIDE
REAR SHOCK TUNING GUIDE ridefox.com sag setting To achieve the best performance from your FOX suspension, adjust the air pressure to attain your proper sag setting. Sag is the amount your suspension compresses
More informationInstallation Instructions
Installation Installation Part # 11503111-2010 up Camaro Recommended Tools 2010-up Camaro TQ Front CoilOver Strut Installation Table of contents Page 2... Included Components Page 3... Disassembly and
More informationpage 3 SCRATCH COIL 9, SCRATCH COIL 7
SCRATCH SUSPENSION SETUP GUIDE page 2 SCRATCH Air 8, Scratch AIR 6 page 3 SCRATCH COIL 9, SCRATCH COIL 7 page 4 Coil fork setup page 5 Coil SHOCK setup Suspension Setup Guide (Scratch 9, Scratch 7) Bike
More informationMarin FRS Quad-Link Service Manual
Marin FRS Quad- Service Manual Table of Contents: 1.0 1, Exploded Diagram: Rear Shock Assembly. 1.1 Parts List: Rear Shock Assembly 2.0 Removal of Rear Shock 3.0 2, Exploded Diagram: Rear Suspension Assembly
More informationSTaSIS / Öhlins Motor Sport Suspension
STaSIS / Öhlins Motor Sport Suspension Damper Model Information Öhlins LMJ Series Damper: Öhlins LMJ stock car shock absorbers are based on the race proven Öhlins 46HRC. A shock absorber featuring a large
More informationWorkshop manual 5018 PDS Product Exploded View Disassembly & Assembling. Shock absorber 5018 PDS OEM Shock absorber 5018 PDS /2002
Shock absorber 5018 PDS OEM 2000 Introduction 2 Exploded view 3 Disassembly shock absorber 4 Disassembly piston-rod 11 Disassembly adaptor DU-bush 15 Assembling adaptor DU-bush 17 Assembling piston-rod
More information.1..2..3..4..5..6..7..8..9..10. MANITOU SUSPENSION FORKS CONGRATULATIONS ON CHOOSING A 2003 MANITOU SIX FORK. This Manitou SIX fork is fully assembled and ready to be installed onto your bicycle. It comes
More informationADJUSTING THE REBOUND DAMPING
GP10 OWNERS MANUAL ADJUSTING THE REBOUND DAMPING The rebound damping in your shock absorber controls the extension or return of the back of the bike. - The more rebound damping you have in a damper, the
More informationw w w. h d o n l i n e s h o p. d e FLHT FRONT END LOWERING KIT GENERAL -J02546 REV Kit Number Models Additional Parts Required
-J0546 REV. 007--0 GENERAL Kit Number 5468-06 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section of www.harleydavidson.com (English only). Additional
More informationInstallation. Installation Instructions Monotube Cartridge Fork Kit 97-Later* Harley Davidson FLH/FLT
Installation Instructions Monotube Cartridge Fork Kit 97-Later* Harley Davidson FLH/FLT ATTENTION Statements in these instructions that are preceded by the following words are of special significance:
More informationFork Set-Up Guide DVOSUSPENSION.COM
Fork Set-Up Guide DVOSUSPENSION.COM Fork Set-Up Guide for Other Languages Pre-Ride Check DOWNLOAD FRANÇAIS ITALIANO DEUTSCH ESPAÑOL Guide d ajustement Guida di sintonia Tuning guide Guía de ajuste 6. Compress
More information