Technical Data Sheet Excel 733-EG

Transcription

1 Technical Data Sheet Excel 733-EG Excel 700 Series Features & Options Standard Features Electrically-operated continuously-hinged movable partition Driven with Ø5 mm [3/16"] steel cable STC 43 or mm [3"] nominal thickness 1230 mm [48 1/2"] maximum width 18 ga welded steel frame Roll-formed steel faces welded to panel frame Panel core made up of one 25 mm [1"] semi-rigid insulation board between two 25 mm [1"] honeycomb boards Trimless vertical edges Vinyl tongue and groove vertical sound seals between panels Final closure at wall jamb Continuous-contact multi-finger fixed vinyl top seals Continuous-contact multi-finger adjustable vinyl bottom seals Steel butt hinges S5X10 steel track Odd-numbered panels supported by one 4-wheeled carrier with steel tires over sealed steel ball bearing wheels Vinyl wallcovering Maximum height: 9220 mm [30-3"] UL/ULC listed drive unit with NEMA-1 motor enclosure and controls and control enclosure conform to ANSI/NEMA ICS1, ICS 2 and ICS 6 15 hp / 208 V / 3 ph / 60 Hz Travel controlled by limit switches Operation by two simultanuously-activated key switches located on each side of the partition Optional Features and Accessories Final closure at pocket door Powder-coated frame and/or track Vertically-ribbed carpet wallcovering Owner-supplied wallcovering (approval required) ADA-compliant pass door with flush pulls and roller latch 733EG_DS_1805_0

2 Optional Features and Accessories (cont d) Door options: - concealed automatic closer - window frame - door viewer - self-illuminated exit sign * - green running man self-illuminated exit sign * - deadbolt lock * (* An exit sign and a deadbolt lock will not be installed together on the same door) Surface-mounted white marker boards 32 mm [1 1/4 ] Horizontal Seals Surface-mounted chalk boards Surface-mounted natural cork tack boards 3-section pocket door fitted with limit switches to prevent operation of the partition until the pocket door is fully opened Drive unit voltage: 1ph 120 V / 240 V (up to 25 panels) 3 ph 230 V / 460 V / 575 V Safety devices: - Infra-red photo-electric sensors prevent/stop operation if one of the beams is interrupted - Safety mats in stack area prevent/stop operation if a mass is detected - Safety lead edge stops operation is it meets an obstacle Operation by one key switch and one push button switch 32 mm [1 1/4 ] 82 mm [3 1/4 ] +25 mm [1 ] / -50 mm [2 ] Floor clearance : 32 mm [1 1/4"] Operating tolerances : +25 mm / -50 mm [+1" / -2 ] - 2 -

3 Vertical Section 125 mm [5 ] Structural support by others Threaded rods by Moderco 305 mm [12 ] MIN Acoustical plenum barrier by others (refer to ASTM E557) #80 Track Hanger bracket 222 mm [8 3/4 ] 19 mm [3/4 ] Black enamelled soffit Black enamelled guide rails Finished floor to underside of ceiling Fabrication height 76 mm [3 ] 305 mm [12 ] Black enamelled adjustable bottom seal Guiding pin (not required if final closure at pocket door) Floor guide (not required if final closure at pocket door) - 3 -

4 Elevation 8 EXIT mm [10-0 ] mm [44 ] 3 1- Infra-red photo-electric sensors 2- Safety mats 3- Floor guide (not required if final closure at pocket door) 4- Exit sign 6- Work surface 7- Eraser box 8- Lead-in bracket 9- Safety lead edge 5- Passdoor - 4 -

5 Plan Views Stack depth 92 mm [3 5/8 ] / pan mm [11 1/2 ] 1/2 panel width mm [6"] MIN 1 1/2 panel width mm [6"] MIN 2 3 Final closure at wall jamb Pocket depth 92 mm [3 5/8 ] / pan mm [20 ] MIN 1/2 panel width mm [8 1/2"] MIN 4 1/2 panel width mm [8 1/2"] MIN 2 3 Final closure at optional pocket door - 5 -

6 Horizontal Sections 228 mm ± 25 mm 51 mm [2 ] [9 ±1 ] Solid blocking by others Wall jamb Panel joint Bulb seal Solid blocking by others 4 Pocket door (optional) - 6 -

7 Drive Unit 400 mm [15 3/4 ] 204 mm [8 ] 711 mm [28 ] 305 mm [12 ] MIN Chain for manual drive 698 mm [27 1/2 ] 152 mm [6 ] Cable for clutch Optional Safety Devices Safety Mats Safety Lead Edge Photo-electric sensors (add 102 mm [4 ] to stack area/pocket width) - 7 -

8 Pocket Door General 2 independent sections and 1 center flap 1 Same surface finish as movable partition / optional custom finish / unfinished Clear anodized frame / optional custom finish Top and bottom locking bolts Low profile hinges PN-73G Non-acoustical Pocket Door 2 Optional for wall-to-wall layout PA-73G Acoustical Pocket Door Fixed top and bottom sweeps Required for wall-to-pocket layout 1275 mm [50 1/4 ] 3 1- Track 2- Flush pulls 3- Locking bolt activators - 8 -

9 Vertical Section Solid blocking required (by others) 25 mm [1 ] 25 mm [1 ] Underside of track Filler jamb Sound seals (PA-73G only) Top locking bolt Bottom locking bolt Sound seals (PA-73G only) 25 mm [1 ] - 9 -

10 Horizontal Section 64 mm [2 1/2 ] 105 mm [4 1/8 ] 500 mm [19 5/8 ] MIN * mm [104 1/4 ] MAX * Sound Seals (PA-73G only) 64 mm [2 1/2 ] Solid blocking required at both jambs (by others) * Min/Max dimensions are fabrication limits and do not account for job-specific conditions Please consult shop drawings or local Moderco distributor prior to sizing pockets