Hover-Ring TM. Warranty & Support

Transcription

1 Warranty & Support This product is provided with a one year warranty for problems found during normal usage. Mistreating the Hover Ring or opening the unit will invalidate this warranty. All out of warranty repairs will be subject to a replacement fee. Technical Support Please visit for the latest product information. feedback@tts-group.co.uk for technical support. TTS Group Ltd. Park Lane Business Park Kirkby-in-Ashfield Nottinghamshire, NG17 9GU, UK. Freephone: Freefax: TTS is proud to be part of Hover-Ring TM WARNING: Do not dispose of this product in household waste. Hand it over to a collection point for recycling electronic appliances. WARNING! Not suitable for children under 36 months due to small parts choking hazard. Made in China, on behalf of the TTS Group Ltd. plc TTS Product Code: PE00994 xx N V

2 Hover-Ring TM Can be used on wood or carpeted floors USER GUIDE

3 Important Information Please read all instructions carefully before using. n Please retain these instructions for future reference, as they contain important information. n All cleaning should be carried out by an adult. n Toys liable to be cleaned with liquids are to be disconnected from the transformer before cleaning. n Ensure the product is switched off before cleaning begins. n To clean the Hover Rings wipe with a damp cloth. Safety Instructions n Your Hover Rings are supplied with a 3 x 1.2V NiMH rechargeable, userreplaceable battery packs. n Batteries should be fitted by an adult. n Use batteries of the same type. n Do not mix new and old batteries; replace all batteries at the same time. n Do not mix rechargeable and non-rechargeable batteries. n Ensure batteries are inserted with the correct polarity. n Do not allow the supply terminals to be short-circuited. n Ensure all used batteries are disposed of in the correct manner. n Do not allow batteries to come into contact with liquids at any time. n It is recommended that rechargeable batteries receive a full charge before long periods of storage. Fitting & Replacing Batteries 1. Your Hover Rings uses 3 x 1.2V NiMH battery packs. 2. Batteries must be inserted with the correct polarity. 3. Remove the battery cover with a screwdriver. 4. Remove the exhausted batteries, and dispose of responsibly.

4 Hover Ring TM 5. Replace the battery cover, and tighten screws A single Hover Ring (PE01103) and the set of 8 Hover Rings (PE00994) These mini hover craft have been designed specifically for the institutional market i.e. schools, clubs, special schools etc. To make sure that they will stand up to the continuous use that they should get, they have been constructed using ABS plastic (toughened) with a superior dense foam skirt. They have additional features designed in so that a wide variety of games can be played with them, giving the greatest appeal to the widest audience, include those groups with special needs. They are fully rechargeable so no need to worry about the expense of cahnging batteries. As with any rechareable product they will benefit from having their batteries completely dischared b before recharging. They come in red and blue (4 of each colour) to allow for team games. Hover Ring operation Before first using, the set of Hover Rings will, need charging for at least 16 hours. Thereafter they should last at least one hour on continuous use setting, much longer on the 20 second cut out setting. Sensible use Hover Rings are designed to stand up to the rigours of continual use by children/ adults in an institutional environment and should, therefore, give many years of life in these settings. It has a rechargeable battery built- in which does away with the worry of having to continually change fiddly batteries and the associated, on-going cost. It comes with its own recharging unit. The devices themselves should never be allowed to get wet or be left out in damp conditions for any period of time. In the event that they do get wet, dry off and place in a warm environment until completely dried out. As with any electrical product, always store in a dry environment. Hover Rings are designed to be used INDOORS only and will not work on outdoor surfaces indeed if you try to use them outside, it may well damage the product and invalidate your warranty.

5 Operation switches on base Switch 1 On/Off/Timed There are two modes: a) On, where the motor stays switched on all the time, or, b) Timed mode, where the motor automatically switches itself off after a period of 20 seconds. To reactivate the Hover Ring in this mode, it just takes a small tap with your hand, foot or pusher. This switch also acts as the off switch. Switch 2 Hover Power The higher the setting, the greater the power, the greater the travel. Apart from the surface, you should take account of the type of game you want to play; some games call for the high setting even though the surface is smooth. There are three settings: HIGH which is designed for carpeted areas and for football games MEDIUM designed most sports hall, gym, canteen areas where the floor is smooth wood, tiles or concrete LOW for smooth floor areas where the distance over which you are playing is 10m or less Note: you will need to experiment on different settings to achieve the desired result for your floor surface Delivery The Hover Rings can be launched by hand ( one or two handed), using the pushers provided or even using the instep of the foot. For those in wheel chairs, the pusher method should work quite well as they are quite light to launch. The Rings will not travel down a boccia ramp. Target Games Three different Target mats are provided in the pack for you to play tarditional target games with. With regards to rules, you will adapt the rules to your particular setting but the rules of bowls, boule or boccia could apply. It is always advised to tape own the leading edge of the mats so that the Hover Rings travel easily ove the front edge. The mats actually have a breaking effect which slows the rings as they travel over the mat.

6 Use Tape Wide, coloured tape makes an effective target medium. Just stick two lengths with a set distance between ( the greater the distance, the easirer it will be to stop the Ring in between the two pieces of tape. For a fully inclusive version of this game stick the tape down in a divergent layout wide at one end and narrow at the other, then players can aim for the space that will give them success. Tape could be used to create boxes to aim at, lines to get close to or to create tram lines inside which the Rings must finish. The players will come up with their own versions! Rebound Games the versatility of the product will allow you to use surfaces to rebound off maybe benches used at an angle or walls. This allows for two dimensional games where the Rings can be sent around corners or have to rebound off one surface before they count. You can have fun with angles and obstacles. Maybe deleop some kind of snooker or billiards variant! Passing Games Just passing the Hover Ring to one another or in a group is a nice activity. From a kneeling position,. Children will love just passing backwards and forwards. It is easy to develop games involving numbers, relicating the same order of delivery. You could pass through a target or hoop or arc. You could create a croquet type game. Delivery could be with the pusher rather than with the hand. Football Passing like a football,with the instep it is robust enough to stand up this kind of use but obviously cannot be kicked against a wall like a normal football. In twos or threes. This is perfectly acceptable for the product provided that the players just pass the Ring and treat with some respect. Again a wall or bench could be used for a variant of this game. Hockey Create a slalom course and,using a plastic hockey stick, dribble in and out of the cones. Pass the Ring to oneanother with a hockey stick players should be encouraged to push rather than strike. Boules, Petanque, Boccia and New Age Kurling Hover Ring TM Many of the games played here could be replicated with the Hover Rings and bring an interesting and 21st century feel to the sports.

7 Know your Hover Rings Fan Inlet Bright LEDs Settings Protective Foam Bumper HIGH ON MED OFF LOW TIMED

8 Using your Hover Rings Your Hover Rings have 2 mode settings: Mode 1 Hover Ring TM Slide the switch to ON and the LEDs and motor will run continuously. HIGH ON MED OFF LOW TIMED Mode 2 - TIMED Slide the switch to TIMED, and the motor and LEDs will run for 20 seconds. After 20 seconds the Hover Ring will turn off. To re-activate knock the top or side of the Hover Ring for a further 20 seconds of use. HIGH ON MED OFF LOW TIMED

9 Your Hover Rings have 3 power level settings: Low Suitable for low frictions surfaces such as polished wooden floors, or table tops. Medium Suitable for medium friction surfaces such as low pile carpets. High Suitable for higher friction surfaces. Hover Rings Additional Features Your Hover Rings are designed to be used indoors and are suitable for all kinds of activities. See website for ideas on activities. International Charging Adaptor & 8-way Splitter The Hover Rings are supplied with a multi-region adaptor. The adaptor is supplied with the UK plug fitted but you can change this easily to suit any country. Press the release button behind the plug head and slide the UK plug out and replace with the required plug module. Slide the plug module in until it clicks in place securely. The safety isolating transformer to be used with the product should be regularly examined for potential hazards such as damage to the cable, cord, plug, enclosure or other parts. In the event of any damage, the adaptor must not be used until the damage has been properly repaired. The toy is not intended for children under 3 years old. The transformer is not a toy. The toy must only be used with the recommended transformer. To save charging time the Hover Rings are supplied with an 8-way splitter, this allows all 8 Hover Rings to be charged at the same time via one socket.

10 Technical Specification Specification Hover Ring TM Battery Type Battery Life (High speed) Battery Life (Medium speed) Battery Life (Low speed) Mode 1 timing period Adaptor 1.2V NiMH battery packs (x3) Up to 1 hour continuous use Up to 1 hour continuous use Up to 1 hour continuous use 20 seconds V 50/60Hz International charging adaptor for UK, EU, CN and AU. 5.5V, 0.5A, Polarity: centre posititve Troubleshooting Problem Hover Rings will not turn on. My Hover Rings only turn on for 20 seconds and then will not work. My Hover Rings do not hover very well. Solution Batteries are flat, recharge using the charging adaptor supplied. Mode 1 is activated. Slide the mode switch to position 2. Motor and LEDs now run permanently. Tap the Hover Ring to reactivate the motor for another 20 seconds. Adjust the power settings for different surfaces. Charge the batteries.