CORDLESS GRASS TRIMMER/EDGER

Transcription

1 CORDLESS GRASS TRIMMER/EDGER Owner's Manual TOLL FREE HELPLINE: Read all safety rules and operating instructions carefully before using this product.

2 Contents STATEMENTS & SAFETY SYMBOLS CONTENTS OF THE PACKAGE 3 GENERAL INFORMATION 3 General Safety Rules Specific Safety Rules Electrical Safety Rules GRASS TRIMMER 7 Technical Data Functions Battery Pack ASSEMBLY 8 Guard Auxiliary Handle Cutting Line OPERATION 0 On Off Switch Adjust the Height of the Trimmer Lengthening the Line Trimming Tips MAINTENANCE BATTERY CHARGER Technical Data Charging Procedure Charger Maintenance BATTERY DISPOSAL 4 WARRANTY 5 PARTS LIST 6 Warning Statements The purpose of the warning statements and safety symbols is to indicate possible danger. Read these statements carefully in order to understand and practice proper accident prevention. DANGER Indicates an EXTREME hazard. Failure to obey a DANGER signal WILL result in serious injury or the death of the operator or others. Always follow the safety precautions in order to reduce the risk of fire, electric shock, and personal injury. Indicates a serious hazard. Failure to obey a signal MAY result in serious injury to the operator or others. Always follow the safety precautions in order to reduce the risk of fire, electric shock, and personal injury. CAUTION Indicates a moderate hazard. Failure to obey a CAUTION signal MAY result in property damage or personal injury to the operator or others. Always follow the safety precautions in order to reduce the risk of fire, electric shock, and personal injury. IMPORTANT! Indicates special mechanical information. NOTE: Indicates additional important general information. Safety Symbols IMPORTANT! Some of the following symbols may appear on the tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow for better and safer operation of. this tool. SYMBOL NAME EXPLANATION V Volt Potential voltage A Amperes Current Hz Hertz Frequency (cycles per second) n0 No load speed Rotational speed at no load.../min Movements Revolutions, strokes, surface per minute speed, orbits, etc. per minute SYMBOL NAME EXPLANATION ~ Alternating Type or a characteristic of current current Direct current Type or a characteristic of current Class II Designates double insulation Ni-Cad Battery Recycling Designates that this tool meets the requirements of the Ni-Cad battery recycling program.

3 Contents of the package Purchasing a battery-powered tool helps to reduce the pollution level in the environment. Please verify the contents of the package against Fig. A. Examine all of the parts carefully before using the cordless grass trimmer or the battery charger. If any parts are missing or damaged, call the toll-free helpline, at In order to reduce the risk of fire, electric shock, and personal injury: Read all instructions carefully before using this tool. Always follow basic safety precautions. Keep these instructions in a safe place for later use. Follow the safety rules in order to avoid injury when using the grass trimmer. Guard Guard Screw Pre-installed on the motor head) Grass trimmer Fig. A Battery charger Battery Extra spool General Information General Safety Rules for All Battery-operated Tools READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all of the instructions listed below may result in electric shock, fire and/or serious personal injury. Work Area Keep the work area clean and well lit. Do not operate a power tool in an explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite dust or fumes. Keep bystanders, children, and visitors away from the work area while operating a power tool. Distractions can cause the operator to lose control. Electrical Safety A battery-operated tool that uses internal batteries or a separate battery pack must be recharged only with the specific charger that is designed for that battery. A charger that may be suitable for one type of battery may create a risk of fire if it is used with another battery. Only use a battery-operated tool with the specific battery pack that is designed for that tool. The use of any other battery may create a risk of fire. Personal Safety Stay alert, watch what you are doing, and use common sense when operating any power tool. Do not use the tool when you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating a power tool can result in serious personal injury. Dress properly. Do not wear loose clothing or jewellery. Contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can get caught in moving parts. Avoid accidental start-ups. Verify that the switch is in the locked or off position before inserting the battery pack. Carrying a tool with a finger on the switch or inserting the battery pack into a tool with the switch in the on position invites accidents. SAVE THIS OWNER'S MANUAL 3

4 Remove adjusting keys or wrenches before turning the tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance allow for better control of the tool in unexpected situations. ALWAYS WEAR EYE PROTECTION. A grass trimmer can throw foreign objects into your eyes which could cause permanent eye damage. ALWAYS wear safety goggles (not glasses). ordinary eyeglases have only impact-resistant lenses...they are NOT safety goggles. Tool Use and Care Do not use tool if it cannot be turned on or off using the switch. A tool that cannot be controlled by the switch is dangerous, and must be repaired. Disconnect the battery pack from the tool or place the switch in the locked or off position before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool accidentally. Store idle tools out of the reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. When battery pack is not in use, keep it away from items such as paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire. Check for misalignment, binding, or breakage of moving parts, and any other condition that may affect the operation of the tool. If the tool is dam aged, have it repaired before using it. Many acci dents are caused by poorly maintained tools. Use only accessories that are recommended for the tool by the manufacturer. Accessories that may be suitable for one tool may create a risk of injury when used with another tool. Service Servicing of this tool must be performed by qualified repair personnel. Service or maintenance that is performed by unqualified personnel may result in a risk of injury. If the tool requires servicing, call the toll-free helpline, at When servicing a tool, use only identical replace ment parts. Follow the instructions in the Mainte nance section of this manual. The use of unauthorized parts or failure to follow Maintenance Instruc tions may create a risk of shock or injury. Specific Safety Rules For ALL Garden Tools Avoid dangerous environments. Do not use tool in damp or wet locations. Do not use tool in the rain. Keep bystanders and children away while operating the tool. Dress properly. Do not wear loose clothing or jewellery, because they can get caught in moving parts. The use of rubber gloves and protective footwear is recommended when working outdoors. Avoid unintentional start-ups. Do not grasp the exposed cutting line when picking up or holding the tool. Do not force the tool. It will do the job better and with less likelihood of injury if it is used at the rate that it was designed to work at. Do not overreach. Keep proper footing and balance at all times. When it is not in use, the tool should be stored indoors in dry location, high up or locked in order to keep it out of the reach of children. Maintain tool with care. Keep the cutting line clean for best performance and in order to reduce the risk of injury. Keep guards in place and in working order. Keep hands and feet away from cutting line. Always use eye protection. SAVE THIS OWNER'S MANUAL 4

5 Specific Safety Rules For Grass Trimmers For Grass Trimmers When lengthening a new cutting line, be careful of the line cutter on the guard. It is sharp. NEVER fit the trimmer with metal cutting elements or blades. Keep ventilation openings clear of debris. Keep handles dry, clean, and free of oil and grease. Before using the grass trimmer, remove any stones, sticks, debris, or other objects that could become entangled in the line or thrown by the trimmer. DO NOT turn the grass trimmer switch to the ON position until it is in the normal operating position. Do not press the lock-off button or squeeze the trigger while the grass trimmer is upside-down. DO NOT reach under the grass trimmer (into the cutting line area) until it has come to a complete stop. The trimmer s cutting line will continue to rotate for approxi mately 5 seconds after it is turned OFF. During operation, be sure that there are no other people. or animals within a radius of (3.7 m). Turn the trimmer OFF when people, and especially children are nearby, or if pets are nearby. Keep the cutting head and the motor clean in order to reduce the risk of injury. Use only the specified size and type of cutting line. Do not substitute. For Battery Pack and Charger DANGER In order to avoid serious injury, the risk of fire or explosion, and the danger of electric shock or electrocution: DO NOT probe the charger with conductive materials. The charging terminals hold 0 V. If the battery pack case is cracked or damaged, DO NOT insert it into the charger. Replace the battery pack. DO NOT charge the battery pack using any other type of charger. Charge only the grass trimmer battery pack that is provided. DO NOT allow liquid to get inside the charger. DO NOT try to use the charger for any purpose other than the purpose that is described this manual. If the battery fluid gets in the eyes, flush them immediately with clean water for at least 5 minutes, and seek immediate medical attention. Do not charge the battery pack in the rain or in wet conditions. Do not immerse the tool, the battery pack, or the charger in water or in any other liquid. Do not allow the battery pack or the charger to overheat. If they are warm, allow them to cool down. Recharge only at room temperature. Do not cover the ventilation slots on the top of the charger. Do not set the charger on a soft surface. Keep the ventilation slots of the charger clear. Do not allow small metal items or material such as steel wool, aluminum foil, or other foreign particles to get into the charger cavity. Unplug the charger before cleaning and when there is no battery pack in the cavity. Do not place the battery charger or the battery pack in the sun or in a warm environment. Store them at room temperature. Do not try to connect two chargers together. The battery pack cells may develop a small leak when used excessively or under extreme temperature conditions. If the outer seal is broken and the leakage gets on your skin: Use soap and water to wash the are immediately. Neutralize the area with lemon juice, vinegar, or some other mild acid. Disconnect the charger from the wall outlet when the battery is fully charged. SAVE THIS OWNER'S MANUAL 5

6 Electrical Safety Rules for the Battery Pack and Charger READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow the safety rules listed below may result in electric shock, fire, and/or personal injury: Do not abuse the cord. Never use the cord to carry the tool. Never pull on the cord in order to disconnect it from the outlet. Keep the cord away from heat, oil, sharp edges, and moving parts. Replace a damaged cord immediately. A damaged cord may create a fire. Do not place the charger where the power cord can be stepped on, tripped over, or subjected to damage. A battery-operated tool that uses internal batteries or a separate battery pack must be recharged only with the specific charger that is designed for that battery. A charger that may be suitable for one type of battery may create a risk of fire if it is used with another battery. Only use a battery-operated tool with the specific battery pack that is designed for that tool. The use of any other battery may create a risk of fire. Grounding (Fig. B) In the event of a malfunction or breakdown, grounding provides the path of least resistance for an electric current, and reduces the risk of electric shock. This battery charger is double insulated, and has a two-pronged polarized plug (one blade is wider than the other). This plug will only fit into a polarized outlet one way. If the plug does not fit in the outlet properly, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper type of outlet. DO NOT alter the plug in any way. IN ALL cases, verify that the outlet is properly grounded. If you are not sure, have the outlet checked by a certified electrician. Extension Cords (Fig. C) Do not use an extension cord for the charger unless it is absolutely necessary. If an extension cord is required, verify that the cord is in good condition. Use an extension cord that is heavy enough to carry the current that the charger will draw. An undersized extension cord will cause a drop in line voltage, which will result in loss of power and overheating. The table below shows the correct size of extension cord to use, depending on the length of the cord and the amperage rating that is listed on the charger's nameplate. When in doubt, use the next heavier gauge. The smaller the gauge number is, the heavier the cord. Verify that extension cord is properly wired and in good condition. Always replace a damaged cord or have it repaired by a qualified electrician. Keep extension cords away from sharp objects, excessive heat, and damp or wet areas. Use a separate electrical circuit for power tools. Do not use any other voltage or power source than common household 0 V electrical power. The circuit must be equipped with not less than # wiring, and should be protected with a 5 A time-delayed fuse. Before connecting the charger to the power line, verify that the electrical current is rated the same as the current that is stamped on the charger's nameplate. To reduce the risk of the charger cord disconnecting from the extension cord during operation, tie them together in a knot. Fig. C Fig. B Properly grounded Grounded outlet Outlet -pronged Prong polarized Polarized plug Plug Ampere Rating Minimum Gauge for Extension Cords (AWG) (when using 0 V only) Total Length of Cord in Feet (meters) More Than Not More Than 5' (7.6 m) 50' (5 m) 00' (30.4 m) 50' (45.7 m) Not Recommended SAVE THIS OWNER'S MANUAL 6

7 Grass Trimmer IMPORTANT! The battery pack is not charged when the grass trimmer is packaged. It is recommended that the battery be to fully charged before the initial use. Refer to the section entitled Charging Procedure Technical Data GRASS TRIMMER Model Number Type Cordless, battery-operated Feed Automatic Speed 6,800 RPM (no load) Trimmer Line (.65 mm) diameter monofilament nylon Cutting Circle Diameter (30 cm) Overall Length (Adjustable) 35 to 44 (89 to.8 cm) Weight 7 lb 6 oz (3.4 kg) with battery Use YARDWORKS replacement battery. Use YARDWORKS replacement spool. Functions (Fig. D) Auxiliary handle To avoid possible injury: The battery pack must always be removed before assembling the guard or adjusting or installing the cutting line spool. The protective guard cannot be removed after it has been installed. Do not operate the grass trimmer without the protective guard in place. Read and understand this Owner s Manual before operating the grass trimmer. BATTERY PACK Type Output voltage Charging time Weight BATTERY CHARGER Input Output Output amperage Rapid charging Overheat protection Battery type Charging time Run Time Weight Lock-OFF button Edging button.7ah Nickel-cadmium rechargeable 4 V DC 90 minutes lb 6 oz (. kg) 0 V AC, 60 Hz 4 V DC.7 A Yes Yes Nickel-cadmium rechargeable hour Up to 30 minutes.4 lbs (0.6 kg) Trigger switch Height adjustment Locking knob Battery pack Battery charger Edging guide Protective guard Cutting spool 7 Fig. D

8 Battery Pack (Fig. E) IMPORTANT! The battery is not shipped fully charged. It is recommended that the battery be fully charged before the initial use. With regular use, the battery pack will take 60 MINUTES or less to charge fully. It is recommended that the battery be charged every 3 months when the trimmer is not in use. The battery's run time will improve after the third or fourth charge. Use YARDWORKS replacement battery. To Remove. Press the latch buttons () in and hold them.. Grasp the trigger handle () firmly. Pull the battery pack out of the handle. NOTE: The battery pack fits snugly into the handle in order to prevent accidental dislodging. Removal may require the use of a certain amount of force. To Install. Align the tongue (3) of the battery pack with the cavity in the handle housing.. Grasp the trigger handle () firmly. 3. Push the battery pack into the handle until both sides lock. The latch buttons will click when they lock. 4, Do not use force when inserting the battery pack. It should slide into place and click. To avoid injury and to reduce the risk of electric shock or fire: Replace the battery pack or the charger immediately if the battery case or the charger cord is damaged. Always verify that the grass trimmer switch is in the OFF position before inserting or removing the battery pack. Always verify that the battery pack is removed and that the switch is in the OFF position before replacing the spools or adjusting the line. Read, understand, and follow the instructions for using the Battery Charger. 3 Fig. E Assembly Guard (Fig. F) To avoid injury, always remove the battery pack before installing the guard or the cutting line, or making any adjustments. If the guard is damaged, do not use the grass trimmer until it is replaced. NOTE: Install the protective guard before using the grass trimmer. Once it is installed, it cannot be removed or disassembled.. Remove the battery pack.. Turn the grass trimmer upside-down in order to access the trimmer head. 3. Unscrew the guard assembly screw () from the base of the trimmer head. The screw has been pre-installed on the motor head for shipping. 4. Fit the guard tabs () into the grooves on the trimmer head so that the guard sits level on the rim of the trimmer head (3). 5. Turn the guard clockwise as far as possible, until it is securely in place. If the guard does not turn easily, readjust the position. 6. When the larger side of the guard is facing the same direction as the handle, the screw hole (4) will be aligned with the hole (5) in the rim of the trimmer head. 7. Insert the screw () into the guard and the trimmer head, and then tighten it securely. 4 5 Fig. F 3 8

9 Auxiliary Handle (Fig. G) To avoid injury, adjust the auxiliary handle for optimum control and balance. Do not overreach when operating the grass trimmer. For better control of the tool in unexpected situations, keep proper balance at all times.. Turn the handle locking knob () counter-clockwise several turns in order to loosen the auxiliary handle ().. Adjust the handle position in order to provide the best level of balance and control for the operator. 3. Securely lock the handle in position by turning the knob clockwise. 4. Before operating the grass trimmer, verify that the auxiliary handle is tightly locked into position. Fig. G Cutting Line (Figs. H) A spool of monofilament cutting line is pre-installed on the grass trimmer. When the cutting line needs to be replaced, insert a new spool. USE YARDWORKS REPLACEMENT SPOOL To avoid personal injury: Do not use any other type of cutting line. Use only 0.065" (.65 mm) nylon monofilament cutting line. The use of wire or other string-like substances can cut clothing and skin, and is very dangerous. Always remove the battery pack before changing the spool or making any adjustments. To Remove the Spool (Fig. H). Remove the battery pack from the trimmer.. Turn the grass trimmer upside-down in order to access the spool line. 3. Remove the spool cover by pressing on the two tabs that are parallel to each other on the side of the cover (). 4. Remove the spool () from the spool housing (3). Fig.H To Replace the Spool (Fig. H). Replace the spool () with a new pre-wound spool.. Insert the end of line through the opening 4) in the spool 4 housing (3). 3. Align the tabs on the spool cover with the slots in the 3 spool housing on the trimmer head. 4. Push down on the spool cover in order to lock it to the spool housing. 5. To advance the line from a newly installed spool, pull the line while pressing the black line release button (5) that is located on the side of the spool housing (4). 5 9

10 Operation On Off Switch (Fig. I) To avoid injury: Do not push the Lock-OFF button down or squeeze the trigger while the grass trimmer is upside-down. Do not carry the grass trimmer with a finger on the switch. Avoid unintentional starting. To Turn the Grass Trimmer On:. Press and hold the Lock-OFF button ().. Squeeze the trigger switch (). 3. Release the Lock-OFF button. The grass trimmer will stay ON as long as the trigger switch is squeezed. CAUTION Always allow at least 5 seconds for the cutting line spool to stop rotating after releasing the trigger switch. Do not turn the grass trimmer upside down or place your hands under the protective guard until the grass trimmer spool has come to a complete stop. To Turn the Grass Trimmer Off:. Release the trigger switch ().. Allow at least 5 seconds for the cutting spool to stop rotating. 3. The grass trimmer will be locked OFF until he Lock-OFF button is pressed again. Adjust the Height of the Trimmer (Fig.J). UNLOCK the height adjuster by sliding the button down toward the motor.. Position the trimmer to the desired height. 3. Release the height adjuster button in order to lock it into position. Fig.I CAUTIO Fig. J Edging Feature (Fig.K) This trimmer is equipped with an edging feature.. To rotate the handle, depress the yellow button (), and turn the handle 80 degrees, until it locks into place.. Rotate the auxiliary handle () 80 degrees in order to align it at the front of the trimmer handle. To rotate the handle, loosen the auxiliary handle tension knob (4) until handle and the holder can be turned easily. 3. Pull the edging guide (3) down until it locks into place. 4 3 Fig. K 0

11 Lengthening the Line(Fig.L) The cutting line gets worn down and becomes shorter as the grass trimmer is used. This trimmer is equipped with Automatic Line Advancement, which automatically feeds additional line in order to maintain the correct length as it wears down.. If the line does not automatically advance, the trimmer line may be tangled or empty. (For instructions concerning how to replace the spool, see Page 9). To advance the line, restart the trimmer. The line will advance automatically when the trimmer is started. AUTO LINE SPOOL ADVANCEMENT NO BUMPING REQUIRED Fig. L IMPORTANT! This grass trimmer is equipped with Automatic Line Advancement. DO NOT BUMP OR TAP THE SPOOL Trimming Tips Before each use Verify that the protective guard is installed securely. Tighten the guard screw. Verify that the battery is fully charged and that the charger is disconnected before using or storing the trimmer. Do not store the grass trimmer in sunlight, in an exces sively warm location, or near a furnace. Doing so will shorten the battery life. If the battery must be stored in a warm place, charge it frequently. Before trimming, inspect the area to be trimmed for string, wire, branches, or any other material that may become entangled in the cutting line or thrown. During use Trim only when the grass and weeds are dry. Do not trim grass at night. Always be sure that there is adequate lighting. For optimum control and balance, hold the grass trimmer by both the switch handle and the auxiliary handle. Stand with the cutting head tipped down at an angle toward the front, guiding the grass trimmer in a semicircular motion around you. If possible, move the grass trimmer toward the left when cutting. The line will cut as soon as it leaves the guard, and the clippings will be thrown away from the operator To produce a smoothly trimmed area, move the grass trimmer in and out of the area that is being cut at a consistent speed and height. Use only the tip of the cutting line to do the trimming, especially near walls and fences. Trimming with the side of the cutting line may overload the motor, wear out the line faster, and break the line more often. Do not rest the trimmer spool on the ground while trimming. This will cause the spool to wear and will drain the battery. If the grass is longer than 6 (5 cm), trim it in stages. When the grass trimmer is turned off and the spool has stopped rotating, the cutting line will relax and may recede. Feed extra cutting line before storing the trimmer in order to prevent the line from receding completely into the spool. If the diameter of the cutting area gets smaller, the line is worn down and needs to be advanced more often. If the grass trimmer is not cutting correctly, the cutting line may not be feeding properly. Remove the line spool and rewind it.

12 Maintenance To avoid the risk of fire, electric shock, or electrocution:. Do not use a damp cloth or detergent to clean the battery or the battery charger.. Always remove the battery pack before cleaning, inspecting, or performing any maintenance on the grass trimmer. Battery Pack. Store the battery pack fully charged.. Recharge the battery pack whenever there is a lack of power. Do not let the battery pack become completely discharged.. The battery will take approximately 90 minutes to fully charge from a discharged state.. Do not recharge a battery pack that is already fully charged. Overcharging shortens the battery life.. Always recharge at a temperature between 50 and 04 F (0 and 40 C). If the battery pack is hot, let it cool down before recharging. If it is hot when it is installed into the charger, the "CHECK BATTERY" indicator light may turn on, indicating that that battery is to warm or hot to begin charging.. After charging, the battery pack can be stored in the charger as long as the charger is not plugged in.. It is recommended that the battery be charged every 3 months when it is not in use. Use YARDWORKS replacement battery Cutting Line. Only replace the cutting line with.065" (.65 mm) nylon monofilament line or with pre-wound replacement spools. (See the section entitled Cutting Line).. Always wind the line in the same direction as the arrow on the spool. Use YARDWORKS replacement spool Cleaning. Wipe the outside of the grass trimmer with a dry soft cloth. Do not hose it down or wash it with water.. Scrape the guard and spool area in order to remove dried clippings and mud. 3. Brush or blow dust, debris, and grass clippings out of the air vents. Keep the vents free of obstructions. CAUTION Do not use strong solvents or detergents on the plastic housing or other plastic components. Certain household cleaners can damage plastic, and may cause a shock hazard. Lubrication No lubrication is needed.

13 Charging Procedure (Fig.M) With regular use, the battery pack will become fully charged in 90 MINUTES or less. Allow the battery to fully discharge before recharging. It is recommended that the battery be charged every 3 months when the trimmer is not in use.. Plug the charger into an AC outlet.. Insert the battery (4) into the charger. Verify that the latch and the battery are fully inserted into the charger. 3. Wait 5 seconds, the RED charging LED light (3) will turn on, indicating that the power source is connected and that the battery is charging. 4. When the battery has reached full charge, the GREEN fully charged LED light () will light up. 5. It is recommended that the charger be removed from the AC outlet once the battery is fully charged. The battery can be stored in the charger. 6. If the AMBER check battery LED light () turns on, it is recommended that the battery (4) be removed from the charger and allowed to cool for 30 minutes. If the check battery LED () remains on after the battery is placed into the charger, contact the toll-free helpline, at Checking the Charge If the battery pack does not charge properly: Check the current at the outlet using another tool. Verify that the outlet is not turned off. Charger Maintenance Mounting the charger (Fig.N) Fig. M 3 4 Verify that the charger contacts have not been shorted by debris or foreign material.. If the surrounding air temperature is not normal room temperature, move the charger and the battery pack to a location where the temperature is between 65 and 75 F (8 and 4 C). : If the battery is inserted into the charger when it is warm or hot, the CHECK BATTERY indicator light may light up. If this occurs, allow the battery to cool outside of the charger for 30 minutes. Note:If both amber and green light illuminate keep battery in charger for approximately 30 minutes and battery will start charging. Keep the charger clean and free of debris. Do not allow. Recharge the battery pack whenever there is a lack of power. foreign material to get into the recessed cavity or onto the Do not allow the battery to become completely discharged. contacts. Wipe with a dry cloth. Do not use solvents or water,. Store the charger at room temperature. Do not store it in and do not place the charger in wet conditions. excessive heat. Do not use the charger in direct sunlight.. Always unplug the charger when there is no battery pack in it. Always recharge in room temperature of 50 to 04 F. Charge the battery fully before placing it in storage. Do not (0 to 40 C). If the battery pack is hot, allow it to cool recharge a fully charged battery pack. Overcharging down before recharging. shortens battery life.. Disconnect the charger from the AC outlet when it is not in use or once the battery has reached full charge.. This charger can be mounted on a wall using two screws (not provided). Determine where the charger is to be mounted. 3. If the charger is being fastened to wooden studs, use wood screws. 4. Drill two holes 4 7/8" (.4 cm) on center, and verify that they are level. 5. If the charger is being fastened to drywall, use wall anchors and screws to secure the charger to the wall. Fig. N 3

14 Environmentally Safe Battery Disposal The toxic and corrosive materials listed below are contained in the batteries that are used in this grass trimmer battery pack: Cadmium, a toxic material. All toxic materials must be disposed of in a specified manner in order to prevent contamination of the environment. Before disposing of a damaged or worn out nickel-cadmium battery pack, contact the local waste disposal agency or the local Environmental Protection Agency for information and specific instructions. Take the battery to a local recycling and/or disposal centre that is certified for disposal of cadmium. If the battery pack cracks or breaks, do not recharge it and do not use it, even if there are no leaks. Dispose of it and replace with a new battery pack. DO NOT ATTEMPT TO REPAIR IT! In order to avoid injury and the risk of fire, explosion, or electric shock, and to avoid damage to the environment: Cover the battery's terminals with heavy-duty adhesive tape. DO NOT attempt to remove or destroy any of the components of the battery pack. DO NOT attempt to open the battery pack. Any leaking electrolytes are corrosive and toxic. DO NOT allow the solution to come into contact with the eyes or the skin, and do not swallow it. DO NOT place this battery in your regular house hold trash. DO NOT incinerate this battery. DO NOT place this battery where it will become part of any waste landfill or municipal solid waste stream. Dispose of this battery at a certified recycling or disposal centre 4

15 WARRANTY For TWO YEARS from the date of purchase within Canada, YARDWORKS CANADA will, at its option, repair or replace for the original purchaser, free or charge, any part or parts found to be defective in material or workmanship. This warranty does not cover:. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or. The unit, if it has not been operated and/or maintained in accordance with the owner's manual; or 3. Normal wear, except as noted below; 4. Routine maintenance items such as lubricants, blade sharpening; 5. Normal deterioration of the exterior finish due to use or exposure. Full One Hundred Twenty Days Warranty on Normal Wear Parts: Normal wear parts are defined as blade adaptors, blades, grass bags and tires. These parts are warranted to the original purchaser to be free from defects in material and workmanship for a period of one hundred twenty (0) days from the date of retail purchase. How to Obtain Service: Warranty service is available by calling the toll-free helpline, at The factory will not accept the return of a complete unit unless prior written permission has been extended by YARDWORKS CANADA. Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. The purchaser must pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by YARDWORKS CANADA. Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the sole and exclusive remedy of YARDWORKS CANADA obligations arising from the sale of its products. YARDWORKS CANADA will not be liable for incidental or consequential loss or damage. 5

16 Parts list Parts Num Model Num. Description. Qty Battery Screw ST4X3-F Handle Switch trigger Spring Switch Spring Lock-Off button Inner wire Screw ST4x6-F Cable holder Sping power line Edging button Fixing tube Auxiliary handle clamp Bolt M6 Locking knob Auxiliary handle Extention tube Spring Female connector Battery socket Sping BoltM4 Housing Motor Spring Line length button Edging guide Spool Spool cover Guard Nylon line Screw ST3x8-C Screw M4x6 Blade holder Screw ST 4x-F Blade Screw Battery charger Owner s manual Printed in China