OPERATING MANUALS FOR 5V, 9V, & 12V SYSTEMS IMPORTANT SAFETY INFORMATION. READ BEFORE USE. DO NOT DESTROY.

Transcription

1 OPERATING MANUALS FOR 5V, 9V, & V SYSTEMS IMPORTANT SAFETY INFORMATION. READ BEFORE USE. DO NOT DESTROY.

2 RAVEANHEAT C6 SYSTEM : 5V QUICK SETUP GUIDE NOTE: CONTROLLER BUTTON IS INSIDE THE LEFT JACKET PANEL A OUTPUT USB SOCKET POWER STRIP LEVEL INDICATOR MINI USB CONNECTOR FOR CHARGING BATTERY USB to Mini USB connector included for charging Grab your Ravean battery and locate the A output USB socket. Make sure the battery is fully charged by shaking it side to side, the power strip will light up blue.. CONTROL BUTTON. USB POWER CABLE PORT. USB POWER CABLE Once your Ravean 5V battery is fully charged, plug the 5V USB power cord into the 5V USB output port. Then. CONTROLLER BUTTON TURNING ON JACKET: Press and hold controller button for - seconds to turn on. The button will light up and pulse red as it preheats (about 5 minutes). Then it will automatically adjust to medium heat (white led light). HIGH HEAT (RED LED): To place your jacket on high heat, press button once after it turns on. The light will go solid red. MEDIUM (WHITE LED): To place your heated jacket on medium heat, press button twice after it turns on. The light will go solid white. LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the control button three times after it turns on. The light will go solid blue. TURNING OFF JACKET: To turn off, press and hold at any temperature setting, until LED light turns off. Press and hold the controller button until the LED light located on the button lights up. Once the LED light is on, your garment will immediately begin warming you.

3 RAVEANHEAT C6 SYSTEM : 9V QUICK SETUP GUIDE NOTE: CONTROLLER BUTTON IS INSIDE THE LEFT JACKET PANEL POWER LEVEL BUTTON LED POWER INDICATOR V OUTLET PORT.6V INLET PORT QC.0 USB 5V/9V OUTLET PORT Before using your heated product, make sure your battery is fully charged. To do this, push the power level button on your battery. When the battery is fully charged, all four LED lights on the LED Power Indicator will light up (see battery manual for charging unstructions).. CONTROLLER BUTTON. 9V USB OUTPUT PORT. 9V POWER CORD Once your Ravean V battery is fully charged, plug the 9V USB power cord into the 9V USB output port.then NOTE: if you are using a non-ravean battery the light on the USB connector will turn solid once it confirms you are using a 9v amp QC.0 battery. If the battery is not compatible it will continue to blink.. CONTROLLER BUTTON TURNING ON JACKET: Press and hold controller button for - seconds to turn on. The button will light up and pulse red as it preheats (about 5 minutes). Then it will automatically adjust to medium heat (white led light). HIGH HEAT (RED LED): To place your jacket on high heat, press button once after it turns on. The light will go solid red. MEDIUM (WHITE LED): To place your heated jacket on medium heat, press button twice after it turns on. The light will go solid white. LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the control button three times after it turns on. The light will go solid blue. TURNING OFF JACKET: To turn off, press and hold at any temperature setting until LED light turns off. Press and hold the controller button until the LED light located on the button lights up. Once the LED light is on, your garment will immediately begin warming you. 5

4 RAVEANHEAT C6 SYSTEM : V THREE BUTTON QUICK SETUP GUIDE NOTE: CONTROLLER BUTTONS ARE INSIDE THE LEFT JACKET PANEL POWER LEVEL BUTTON LED POWER INDICATOR V OUTLET PORT.6V INLET PORT QC.0 USB 5V/9V OUTLET PORT Before using your heated product, make sure your battery is fully charged. To do this, push the power level button on your battery. When the battery is fully charged, all four LED lights on the LED Power Indicator will light up (see battery manual for charging unstructions).. CONTROLLER BUTTONS. V OUTPUT POWER PORT. V POWER CORD Once your Ravean V battery is fully charged, plug the v power cord into the v output port. Then. CONTROLLER BUTTONS TURNING ON JACKET: Press and hold any of the controller buttons for - seconds to turn on. The button will light up and pulse red as it preheats (about 5 minutes). Then it will automatically adjust to medium heat (white led light). HIGH HEAT (RED LED): To place your jacket on high heat, press button once after it turns on. The light will go solid red. MEDIUM (WHITE LED): To place your heated jacket on medium heat, press button twice after it turns on. The light will go solid white. LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the control button three times after it turns on. The light will go solid blue. TURNING OFF JACKET: To turn off, press and hold at any temperature setting until LED light turns off. Press and hold the controller buttons until the LED light located on the button lights up. Once the LED light is on, your garment will immediately begin warming you. 6 7

5 RAVEANHEAT C6 SYSTEM : V QUICK SINGLE BUTTON SETUP GUIDE NOTE: CONTROLLER BUTTONS ARE INSIDE THE LEFT JACKET PANEL POWER LEVEL BUTTON LED POWER INDICATOR V OUTLET PORT.6V INLET PORT USB OUTLET PORT Before using your heated product, make sure your battery is fully charged. To do this, push the power level button on your battery. When the battery is fully charged, all four LED lights on the LED Power Indicator will light up (see battery manual for charging unstructions).. CONTROLLER BUTTONS. V OUTPUT POWER PORT. V POWER CORD Once your Ravean V battery is fully charged, plug the v power cord into the v output port. Then. CONTROLLER BUTTONS TURNING ON JACKET: Press and hold any of the controller buttons for - seconds to turn on. The button will light up and pulse red as it preheats (about 5 minutes). Then it will automatically adjust to medium heat (white led light). HIGH HEAT (RED LED): To place your jacket on high heat, press button once after it turns on. The light will go solid red. MEDIUM (WHITE LED): To place your heated jacket on medium heat, press button twice after it turns on. The light will go solid white. LOW HEAT (BLUE LED): To place your heated jacket on low heat, press the control button three times after it turns on. The light will go solid blue. TURNING OFF JACKET: To turn off, press and hold at any temperature setting until LED light turns off. Press and hold the controller buttons until the LED light located on the button lights up. Once the LED light is on, your garment will immediately begin warming you. 9

6 RAVEANHEAT C6 SYSTEM : V RUGGED JACKET SETUP GUIDE NOTE: CONTROLLER BUTTONS 6. CONTROLLER BUTTONS POWER LEVEL BUTTON LED POWER INDICATOR V OUTLET PORT.6V INLET PORT USB OUTLET PORT 6 FLASHLIGHT BUTTON Before using your heated product, make sure your battery is fully charged. To do this, push the power level button on your battery. When the battery is fully charged, all four LED lights on the LED Power Indicator will light up (see battery manual for charging instructions). FLASHLIGHT OPERATION To operate flash light press and hold the button for -5 seconds, to turn off, press and hold for -5 seconds.. CONTROLLER BUTTONS. V OUTPUT POWER PORT. V POWER CORD Once your Ravean V battery is fully charged, plug the v power cord into the v output port. Then TURNING ON: Press and hold any of the controller buttons for - seconds to turn on. The button will light up and pulse red as it preheats (about 5 minutes). Then it will automatically adjust to medium heat (white led light). HIGH HEAT (RED LED): To place on high heat, press button once after it turns on. The light will go solid red. MEDIUM (WHITE LED): To place on medium heat, press button twice after it turns on. The light will go solid white. LOW HEAT (BLUE LED): To place on low heat, press the control button three times after it turns on. The light will go solid blue. TURNING OFF JACKET: To turn off, press and hold the button until LED light turns off. Press and hold the controller buttons for the jacket or cuffs until the LED light located on the button lights up. Once the LED light is on, your garment will immediately begin warming you.

7 RAVEAN V MOBILE CHARGING 0 5. USB POWER CORD. MOBILE DEVICE. HAND POCKET. MEDIA HOLE STEP Plug your mobile device's USB power cord into your mobile device. Then, thread the USB cord through the media hole found inside the jacket pocket.. BATTERY POCKET. USB OUTPUT. BATTERY POCKET MEDIA HOLE. CORD CHANNEL 5. HAND POCKET MEDIA HOLE STEP Feed the USB cable through cord channel inside the jacket and into the media hole on the battery pocket. Plug the USB cord into the USB output on the battery. Replace the battery into the battery pocket. HEATED PRODUCT WARNINGS AND SAFEGUARDS Please read the product label and all of the instructions before using your heated product. As with all electrical products, misuse of your heated product and/or failure to properly follow the instructions may cause overheating, fire, personal injury, or death. INSTRUCTIONS FOR USE. If you have a medical condition which makes you sensitive to overheating or you use any personal medical devices, ask your physician to determine if use of this product is appropriate. DO NOT use your heated product on: An infant or young child An incapacitated or immobile person A paraplegic or quadriplegic A diabetic Anyone insensitive to heat, such as a person with poor blood circulation Anyone who cannot clearly understand the instructions and/or operate controls. DO NOT use if inner liner is wet. Water will increase the risk of electric shock.. DO NOT abuse the power cable. Never use the cord for carrying, pulling, or unplugging the heated jacket. Keep cord away from heat, oil, sharp edges, or moving parts.. DO NOT use the heated jacket if the power indicator button on the battery isn t working. 5. DO NOT allow heating elements to touch bare skin. 6. DO NOT allow the cords to be pinched. 7. DO NOT use pins. They may damage the electric wiring. 8. If the heated jacket turns off unexpectedly, check connections and make sure your battery pack is charged. 9. SHUT OFF power immediately if any discomfort occurs. 0. ALWAYS REMOVE BATTERY PACK before changing or removing accessories. Only use accessories specifically recommended for this jacket. Others may be hazardous. For a complete listing of accessories for your Ravean jacket go online to ravean.com.. If the heated jacket does not start or operate properly with a fully charged battery pack, clean the contacts on the battery pack. If the heated jacket still does not work properly, contact Ravean at support@ravean.com. NEVER disassemble the heated jacket, battery, or charger.. Your jacket may be safely used at temperatures between F and 0 F (-0 C and 60 C). Use the heated jacket in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the heated jacket for operations different from those intended could result in a hazardous situation. BATTERY WARNINGS AND SAFEGUARDS Rechargeable lithium-ion batteries are potentially hazardous and can present a serious FIRE HAZARD if damaged, defective, or improperly used.. DO NOT try to heat the product and charge the battery at the same time.. DO NOT charge battery inside battery pocket.. DO NOT try to disassemble or cut battery.. DO NOT expose to high heat or direct sunlight for long periods of time. 5. DO NOT burn or incinerate battery. 6. DO NOT use if battery case is cracked or damaged. 7. DO NOT use if there is leakage or case bulges. 8. DO NOT use battery with any non-ravean v chargers. 9. DO NOT expose battery to any type of liquid. 0. DO NOT charge at temperatures below 0 F ( C).. DO NOT store at temperatures higher than 70 F (76 C). This can potentially result in self-combustion. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, seek medical help. Liquid ejected from the battery may cause irritation or burns. If you see your heated product or battery is operating improperly, unplug it immediately and contact Ravean at support@ravean.com HEATED JACKET STORAGE AND CARE. Disconnect the battery pack from the heated jacket before storing. This prevents you from accidentally turning on the jacket.. Batteries should be stored at temperatures between 0 F and 80 F ( C and 7 C) for maximum life and safety.. For maximum life, batteries should be stored at 0% to 70% charge.. Batteries in long-term storage at room temperature should receive a charge every three months or so. 5. DO NOT leave the battery in the jacket overnight or while not in use. 6. Maintain heated jacket. Check for breakage of parts and any other condition that may affect the heated jacket s operation. If damaged, contact Ravean at support@ravean.com. 7. Recharge only with the Ravean charger. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. 8. Use heated jacket only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. 9. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. 0. Before washing, disconnect and remove battery pack from jacket. Push the power cord completely into the battery pocket and fasten closed.. NEVER immerse your battery holder, battery pack, or charger in liquid or allow any liquid to flow inside them.. Maintain labels; they carry important information. If labels are unreadable or missing, contact Ravean for free replacement. CHARGING INSTRUCTIONS The following recommendations, in addition to the precautions above, should be followed when charging lithium-ion batteries to ensure the avoidance of potentially catastrophic fire or explosion.. Charging should be performed in a firesafe area, away from children or pets. NEVER charge batteries unattended, for longer than -hours, or where objects such as carpet, furniture, wood or vinyl floors, curtains, or other flammable objects are present.. Charging should be performed at a temperature between 0 F and 0 F ( C and C). Never charge below 0 F ( C).

8 . DO NOT attempt to charge a battery that is swollen or bulging.. USE ONLY supplied charging cables and connections. Make sure connections are in good condition. 5. DO NOT allow the charging polarity to be reversed or short-circuited. 6. Observe the battery in a safe place for at least 5 minutes after charging is complete, as a delayed chemical reaction can occur if a fault is present. 7. A healthy battery should only get slightly warm during charging. If the battery becomes hot, smokes, swells, or gives off an odor during charging, terminate charging immediately and contact the Ravean support. NOTE: the charger itself may get quite warm to the touch when charging a deeply discharged battery. A FIRE IS MOST LIKELY TO OCCUR DURING THE CHARGING PROCESS UNDER THE FOLLOWING CIRCUMSTANCES:. THE BATTERY HAS BEEN FULLY DISCHARGED AND IS NOT RECHARGED SHORTLY AFTERWARD. This potential is aggravated if batteries are damaged, contain an undetected factory defect, are used or stored at temperature extremes, or are approaching the end of their useful life. Ideally, batteries should be recharged within hours of a full discharge.. CHARGING IS ATTEMPTED AT TEMPERATURES BELOW 0 F ( C). Charging below 0 F ( C), causes a chemical reaction in the battery cells that can cause permanent damage and the possibility of fire or explosion during charging.. THE BATTERY HAS BEEN EXPOSED TO LIQUIDS, ESPECIALLY SALTWATER. Exposure to liquids can cause internal corrosion or damage to the cells or to the Battery Management System (BMS). The BMS protects the battery from overcharging, high self-discharge, or imbalanced charging of the cells, any of which can present the possibility of fire during recharging.. OPERATING OR CHARGING A BATTERY OR BATTERY CHARGER THAT HAS BEEN DAMAGED from dropping or from shipping damage, or damaged in any way. A damaged battery is subject to explosion or fire. Properly dispose of a dropped or damaged battery immediately. 5. USING A CHARGER OTHER THAN THE ONE SPECIFICALLY DESIGNATED FOR THE BATTERY BY RAVEAN. A charger that is suitable for one type of battery pack may create risk of fire when used with another battery pack. SAFE DISPOSAL OF LITHIUM-ION BATTERIES Lithium-ion batteries contain elements that may pose health risks to individuals. If not disposed of properly, they can leach into the groundwater supply. In some countries, it may be illegal to dispose of these batteries in standard household waste. Fortunately, many recycling facilities exist that process lithium-ion batteries, in part due to the value of the materials contained within the individual cells. In the United States and Canada, a large network of over 0,000 battery drop-off locations may be found at To render the battery safe, apply tape over any exposed connectors to prevent the accidental shorting of the positive and negative terminals of the battery during transport. Place each battery into its own plastic bag, seal the bag, and deposit the battery into the recycling container. NEVER dispose of the battery in a fire or incinerator, as the battery may catch fire and explode. WASHING AND SPOT CLEANING If your down jacket gets a few areas of light dirt or other substances, you don t need to wash the whole thing. Use a small drop of liquid detergent and lightly scrub the affected area with a wet towel until clean. WASHING YOUR DOWN JACKET. Before washing, disconnect and remove battery pack from jacket. Push the power cord completely into the battery pocket and fasten closed.. Use a small amount of stain remover or down wash to treat any really dirty spots.. Place your jacket in the washing machine on delicate cycle, set to cold (not hot or warm), and add the down wash as directed.. Dry on the lowest heat setting on your dryer. If desired, you can throw in three clean tennis balls to help break up wet clumps of down. If you don t have any tennis balls, you can put shoes inside clean socks or make sock balls as a substitute. The drying process will be slow, but it s the most important part. Be patient. The jacket will usually take around - hours to dry. 5. Make sure your jacket is completely dry before packing or compressing it. Compressing wet down can hurt the insulation properties and cause mold to form. 6. Always store your down jacket uncompressed in a clean and dry spot. HAND WASH INSTRUCTIONS. Mix tsp (5mL) vinegar into cold water then place the garment in water for 5-0 minutes. Use a soft brush to remove dirt. DO NOT rub the garment.. Squeeze the water out of garment. Do not wring.. Use clean water to rinse away remaining detergent.. Wrap a clean, dry towel around the garment and squeeze out any remaining moisture.. Let air-dry on a flat, clean surface or hang on a plastic hanger. Avoid exposure to sun.. DO NOT IRON.. Once the garment is dry, flap it up and down several times to fluff the down. Always store your down jackets uncompressed in a clean and dry spot. MACHINE WASH, GENTLE CYCLE IN COLD WATER DO NOT BLEACH DO NOT WRING OUT OR TWIST TUMBLE DRY, LOW HEAT DO NOT IRON DO NOT DRY CLEAN RAVEAN LIMITED WARRANTY POLICY & GUIDELINES Ravean stands behind the quality of everything we sell, and we hope you re happy with your heated product. If you encounter any problems with the operation of our products, or you would like to give us feedback on our jackets, please contact us through our website at ravean.com The Ravean products are warranted to the original owners against manufacturing defects in materials and workmanship for 90 days. It does not cover normal wear and tear. Wear and tear is damage that naturally and inevitably occurs as a result of normal use. Regardless of how carefully you use or how well you care for your Ravean jacket, it will eventually begin to show age and wear. Common examples of wear and tear that would not be covered under the warranty include colors fading, abrasions on the bottom of battery packs or at the cuffs/pockets from rubbing when you walk, and general breakdown of the materials over the years. Only original, unaltered, and unmodified materials and workmanship are covered by this policy. This warranty does not cover damage caused by accident, improper care, negligence, normal wear and tear, or the natural breakdown of colors and materials over extended time and use. To return a Ravean item for warranty evaluation, you will need a Return Authorization number (RA number), which can only be obtained directly from the Ravean Warranty Department. To initiate the warranty process, please send an to warranty@ravean.com. Please include the following in your Full name and address associated with the order Detailed description of the issue you are experiencing The Ravean Warranty Department will help resolve the issue and give you an RA number with further instruction. If necessary, we will have you send the jacket into us for evaluation. All costs for shipping and insuring products sent in for evaluation must be prepaid by the customer. No return shipping labels are provided. Any COD will be refused and fees incurred by the customer. Any product that is returned without an RA number will be returned unopened Ravean is not liable for lost in-bound packages. Utah state law requires that products accepted for repair must be clean. Charges will be assessed if cleaning is necessary, and the heated jacket may be returned to you if it cannot be adequately cleaned. This warranty is available worldwide. This warranty gives you specific legal rights; you may have other rights, which vary from state to state. RAVEAN LIABILITY Ravean will not be liable for any incidental or consequential damages caused by the breach of any express, implied, or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. Ravean disclaims all other warranties, conditions or representations, express, implied, statutory, or otherwise. Ravean shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the heated product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states, or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state, or jurisdiction to jurisdiction. For questions or support, please visit ravean.com or at support@ravean.com FCC Notification: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following: - Reorient or relocate the receiving antenna; - Increase the separation between the equipment and receiver; - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; - Consult the dealer or an experienced radio/tv technician for help. In accordance with the rules and regulations of the FCC, changes or modifications to this equipment, not expressly approved in writing by Ravean could void the user s authority to operate this equipment. For questions or support, please visit ravean.com PLEASE DO NOT RETURN THIS PRODUCT TO PLACE OF PURCHASE. 07 Duralogic USA LLC. Doing business as Ravean. All rights reserved. Distributed by Ravean

9 Designed in Utah Made in China ravean.com/manuals RUM-07