DISTRICT OF COLUMBIA DEPARTMENT OF TRANSPORTATION BRIDGE FAÇADE LIGHTING STUDY

Transcription

1 DISTRICT OF COLUMBIA DEPARTMENT OF TRANSPORTATION BRIDGE FAÇADE LIGHTING STUDY FOR BRIDGE NO. 007 FRANCIS SCOTT KEY BRIDGE DATE: April, 2014 Prepared By:

2 BRIDGE FAÇADE LIGHTING STUDY FOR BRIDGE NO. 007 FRANCIS SCOTT KEY BRIDGE TABLE OF CONTENTS 1. Introduction Proposed Lighting Source Lighting Concept Lighting Concept Lighting Concept Accessibility Recommendation Appendix A Lighting Specification Sheets 9. Appendix B Data Enabler Pro DMX Controls

3 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. BRIDGE FAÇADE LIGHTING STUDY FOR BRIDGE NO. 007 FRANCIS SCOTT KEY BRIDGE Introduction: The Francis Scott Key Bridge was completed in 1923 to span the Potomac River connecting Georgetown in Washington, D.C. to Rosslyn in Arlington County, Virginia. The bridge has undergone modification on three later occasions in 1939, 1955, and The bridge is oriented in a generally north-south direction. The Classically inspired structure is made of reinforced concrete, with eight primary arches. Five of the arches span over the river, while the other three span land features. Of the associated seven piers, four have their foundations covered by the water. The Georgetown arches over land are generally obstructed from river view by the Whitehurst freeway and trees at their base. The Virginia arch over land spans the George Washington Parkway, but is also obstructed at its southern-most pier by bushes and trees. Francis Scott Key Bridge-view from Virginia The overall objective of this project is to provide a general restoration to the bridge and vehicular barriers, as well as add bridge lighting to the face of the bridge. There are three lighting concepts studied herein for this purpose: 1) uplighting of the outer facades from the piers, 2) downlighting of the outer facades from the underside of the walkway, and 3) lighting from within the arches to provide silhouette highlights through the smaller arches penetrating the spandrels above each primary arch. Illumination levels on the bridge face will be kept to a relatively low average of 1 footcandle so as not to blind boaters from clearly seeing the navigational lights at the base of the piers. Francis Scott Key Bridge February 24, 2014

4 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. Proposed Lighting Source: Before getting too far into a discussion on the relative merits of each concept, a proposed lighting source needs to be evaluated. Traditional light sources considered for this type of application would be high intensity discharge lamps (HIDs) utilizing either metal halide or high pressure sodium medium. The lamps would be housed in base-mounted floodlight enclosures with internal reflector optics ranging from longnarrow to square-wide distributions depending on the distance of the light from its target and the dimensions of area to be lit. Any colors introduced into the application would be colored lens covering the full aperture of the light or mounted as a disc in a rotating wheel allowing the projected colors to be changed. Modern technology has provided a dramatically improved option for the designer in the form of LED (lightemitting diode) type lights. Many different lighting intensities and distributions are available within the same housings and a host of color variations are afforded by the controlled operation of tri-color red, blue, and green LED s within the same panel. The LED light for a particular function usually requires about 1/3 of the power of traditional HID s and a greatly extended life of 100,000 hours. At 12 hours of operation for 365 days a year, the LED floodlight can last over 22 years without the need to replace ballast or lamps, greatly reducing the net present value of a design based on this light source. The particular LED light we have considered in our study is the Phillips Coloreach Powercore gen2 with 63 degree spread lens (see attached specification sheet). We have also studied results from a Hydrel 8200 series color-changing and monochromatic units and a Lithonia DS3 series monochromatic floodlight. The color-changing units have an option for intelligent color control via integration with Data Enabler Pro DMX controller. With each light connected to a dmx network, special effects can be created such as having a red, white, and blue pattern moving across the bridge to simulate a flag waving in the wind. Or, as in the case of the Ben Franklin Bridge in Philadelphia, a lighting sequence with the Philips Coloreach that appears to chase a train as it crosses the bridge. While we have identified the needed components and have approximate pricing for each, a discussion regarding DDOT feedback to such a consideration and the determination of a proposed budget for the new lighting system are warranted before a final BOM and installed cost can be established. However, the different lighting patterns that can be provided by this type of control system and floodlight are only limited by imagination, and rough-order-of-magnitude pricing for basic components will be offered with the discussion of each concept. Regardless if we proceed with color-changing effects or not, we recognize that the proposed lighting scheme will require review and approval from NPS, CFA, and Georgetown BID. The service voltage for these lights will be 240VAC, and may require an upgrade to the existing bridge electrical service. A more detailed discussion on the electrical power requirements will be developed during design of the selected lighting system and options. However, estimated annual electrical costs will be supplied for each concept assuming a $0.15/kwh rate and the full 290W power consumption per light. Lighting Concept 1: The first lighting concept has one or more floodlights located at the base of each pilaster on top of the pier s foundation and aimed up to the underside of the protruding walkway. Uplighting is the classical approach for lighting this type of façade and can be accomplished readily with the optics available in our selected product. However, some apprehension is due as the northern approach pattern to the Ronald Reagan National Airport located a few miles south of this bridge passes directly over the bridge. While a strong argument can be made that the lights will be located, directed, and screened from view by the Francis Scott Key Bridge April, 2014

5 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. walkway extension so as to not be a potential blind for pilots, any design with an uplighting component may well require Federal Aviation Administration review and acceptance. The least potentially offensive uplighting option places a single, wide angle light at the pier base, roughly 5 from the vertical line of the bridge face and directed back at about a degree angle from nadir. The best option places three lights at the bases with one aimed directly up along the face of the pilaster and the other two aimed at the top of each adjacent arch. Uplighting from Base-One Light Uplighting from Base-Three Lights Assuming that lighting will be provided for the full length of the bridge, at arches both over land and water, approximate light costs (with no color options) for the least option are $100,000. Approximate costs for the best uplighting option, no colors, are $330,000. The color option would range from approximately an additional $10,000 to $30,000. Estimated annual energy costs are $3,000 and $8,000, respectively. Lighting Concept 2: The downlighting concept from the underside of the walkway eliminates any concerns with needing FAA review, and also allows us to get a little further away from the bridge face and get somewhat better uniformity of the light intensity across the face from pier to pier. In this concept, two lights would be placed at the top of each pilaster, directed to the arches on either side, and one above the top of each arch. The wide angle lights above the arch could be have substantially lower lighting output as it is only throwing the light about half of the height of the bridge. Downlighting from Underside of Walkway Approximate costs for this option are $350,000 with no color options. The color option for this concept would be approximately an additional $25,000, and estimated annual energy cost is $8,000. Francis Scott Key Bridge April, 2014

6 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. Lighting Concept 3: Lighting from within the bridge provides the most dramatic effect by projecting light through the arches, providing a depth to the visual effect and highlighting the most important architectural feature of the bridge, the arches upon arches. The plan would be to have a light from each pier directed back to the top of each of the three arches (two narrow width arches on each side and one wider arch at the center) over each span. The lights would feature a wide angle distribution to really punch light into the gap between arches and get reflected light to illuminate the interior widths of the smaller arches. Cavities between Center Arch and Outer Arches Catwalk between arches Costs for this option would be approximately $210,000, with an additional approximate $15,000 for color options. Estimated annual energy cost is $5,300. Accessibility: Lights at base of pier can be accessed from ladders or scaffolding off the decks of barges or boats anchored directly against the foundation walls. Lights installed at the underside of the walkway need scaffolding rigged off of and lowered over the outer edge. Lights inside of the arches are accessed by the catwalk system existing under the bridge, and are most conveniently mounted for maintenance directly to the catwalk railings at the top of and between the center and outer arches. No additional costs are expected for the lighting installation as the work platforms already planned for the structural restoration will be sufficient for the lighting work and can be coordinated for use by the electrical contractor as well. There is some concern about the lights on the foundation base getting submerged in heavy floods as they would not be far above the mean high water elevation. These lights would also be susceptible to being covered by snow and ice in the winter. This is not as much of a concern with normal quartz or HID floodlights as they operate at elevated temperatures and eventually melt away snow cover. LED lights, though, operate with little to no heat given off and could stay covered for extended periods of time. Recommendation: If DDOT chooses to pursue lighting on the Key Bridge, we believe that a combination of two concepts, the least option for uplighting the bridge face along with the highlighting of arches from within, will provide the most dramatic effect. FAA coordination will be necessary, but this approach accomplishes emphasis of both vertical mass and depth, a three-dimensional treatment that showcases the classical structural elements of the Key Bridge. Approximate costs are $310,000 for lights and $30,000 for color options. Francis Scott Key Bridge April, 2014

7 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. Appendix A Lighting Specification Sheets Francis Scott Key Bridge February 24, 2014

8 Date: Type: Firm Name: Project: ColorReach Powercore gen2 63 spread lens Premium long-throw exterior LED floodlight with intelligent color light ColorReach Powercore gen2 combines all the benefits of LED-based lighting and control in an elegant fixture specifically designed for large-scale installations, such as skyscrapers, casinos, bridges, piers, public monuments, and themed attractions. With levels of light output and projection never before achieved in an LED lighting fixture, ColorReach Powercore gen2 affords entirely new possibilities in exterior illumination. Integrates Powercore technology Powercore technology rapidly, efficiently, and accurately controls power output to fixtures directly from line voltage. Philips Data Enabler Pro merges line voltage and control data and delivers them to fixtures over a single standard cable, dramatically simplifying installation and lowering total system cost. Versatile optics A native 5 beam angle and exchangeable spread lenses of 8, 13, 23, 40, 63, and an asymmetric 5 x 17 support a variety of photometric distributions for a multitude of applications, including spotlighting, wall grazing, and asymmetric wall washing. Bezel and gasket are included with spread lenses for easy user installation. Unique split design supports diffuser combinations Each half of the fixture is individually addressable and controllable. For instance, you could use one spread lens on the fixture s lower half to bathe a large façade with color at street level, and a different spread lens to project a contrasting or complementary color hundreds of feet up the building s walls. Saturated, cost-effective color Highperformance LEDs offer rich, saturated color at significantly less cost for installation, operation, and maintenance than traditional light sources. Simple fixture positioning Rugged, slimprofile mounting bracket allows simple positioning and fixture rotation through a full 360. Side locking bolts reliably secure fixture with a standard wrench. 4.8 in (122 mm) 18 in (457 mm) Ø1.05 in (27 mm) Ø.53 in (13 mm) 4X 3 in (76 mm) 3.5 in (89 mm) 28.9 in (734 mm) 6 in (152 mm) in (692 mm) 5 in (127 mm) 12 in (305 mm) 13.6 in (345 mm) 20.5 in (521 mm) 1.5 in (38 mm) Universal power input range Fixtures accept a universal power input range of VAC, allowing consistent installation in any location around the world. Industry-leading controls Fixtures work seamlessly with the complete Philips Color Kinetics line of controllers, including Light System Manager, iplayer 3, and ColorDial Pro, as well as third-party controllers. For detailed product information, please refer to the ColorReach Powercore gen2 Product Guide at colorreach/

9 Specifications Due to continuous improvements and innovations, specifications may change without notice. Item Specification Details Output Electrical Control Physical Certification and Safety Fixtures and Accessories Item Type Item Number Philips 12NC ColorReach Powercore gen2 Includes 6 ft (1.8 m) leader cable UL / cul and CE / PSE Replacement Leader Cable 6 ft (1.8 m) ColorReach Powercore Spread Lens with bezel Data Enabler Pro Lumens* LED Channels Mixing Distance 3709 (half unit) Red / Green / Blue 50 ft (15.2 m) to uniform light Lumen Maintenance 100,000 hours 25 C 85,000 hours 50 C Input Voltage Power Consumption Interface Control System Dimensions (Height x Width x Depth) Weight Effective Projected Area (EPA) Housing Lens Fixture Connections Temperature Ranges Humidity Fixture Run Lengths Certification Environment VAC, auto-switching, 50 / 60 Hz 290 W maximum at full output, steady state Data Enabler Pro (DMX / Ethernet) Philips Color Kinetics full range of controllers, including Light System Manager, iplayer 3, and ColorDial Pro, or third-party controllers 20.5 x 28.9 x 4.8 in (521 x 734 x 122 mm) 75 lb (34 kg) 0.42 m 2 Die-cast aluminium, powder-coated finish Tempered glass Integral male / female waterproof connector, 6 ft (1.8 m) unified power / data cable F ( C) Operating F ( C) Startup F ( C) Storage 0 95%, non-condensing To calculate fixture run lengths and total power consumption for your specific installation, download the Configuration Calculator from UL / cul, FCC Class A, CE, PSE, C-Tick Dry / Damp / Wet Location, IP66 * Lumen measurement complies with IES LM testing procedures L50 = 50% lumen maintenance (when light output drops below 50% of initial output). Ambient luminaire temperatures specified. Lumen maintenance calculations are based on lifetime prediction graphs supplied by LED source manufacturers. Calculations for white-light LED fixtures are based on measurements that comply with IES LM testing procedures. Refer to www. philipscolorkinetics.com/support/appnotes/lm pdf for more information. UL / cul CE / PSE Asymmetric (5 x 17 ) /4 in / 1/2 in NPT (U.S. trade size conduit) PG21 / PG (metric size conduit) Use Item Number when ordering in North America. Photometrics 63º spread lens, half unit Polar Candela Distribution Cd: ,200 1,800 2,400 3,000 3,600 VA: 0º 10º 20º 30º 40º Cd: 0 38,500 77, , , ,000-0º H - 90º H 4.0 ft 8.0 ft 12.0 ft 16.0 ft 20.0 ft 24.0 ft For lux multiply fc by 10.7 VA: 0º 10º 20º 30º 40º - 0º H 90º º º º º Illuminance at Distance Center Beam fc 221 fc 55 fc 25 fc 14 fc 9 fc 6 fc 59.5 ft (18.1 m) 1 fc maximum distance 5 native (no spread lens), half unit Polar Candela Distribution - 90º H 4.0 ft 8.0 ft 12.0 ft 16.0 ft 20.0 ft 24.0 ft 90º 80º 70º 60º 50º Illuminance at Distance Center Beam fc fc 3605 fc 1602 fc 901 fc 577 fc 401 fc 480 ft (146.3 m) 1 fc maximum distance Beam Width 4.5 ft 4.6 ft 9.0 ft 9.1 ft 13.5 ft 13.7 ft 17.9 ft 18.2 ft 22.4 ft 22.8 ft 26.9 ft 27.4 ft Vert. Spread: 58.5º Horiz. Spread: 59.3º LED Lumens Efficacy RGB MULTIPLY CANDELA VALUES BY 10 Beam Width 0.5 ft 0.5 ft 1.0 ft 1.1 ft 1.5 ft 1.6 ft 2.0 ft 2.1 ft 2.5 ft 2.6 ft 3.0 ft 3.2 ft Vert. Spread: 7.1º Horiz. Spread: 7.6º LED Lumens Efficacy RGB Half Philips Color Kinetics 3 Burlington Woods Drive Burlington, Massachusetts USA Tel Tel Fax Copyright Philips Solid-State Lighting Solutions, Inc. All rights reserved. Chromacore, Chromasic, CK, the CK logo, Color Kinetics, the Color Kinetics logo, ColorBlast, ColorBlaze, ColorBurst, ew Fuse, ColorGraze, ColorPlay, ColorReach, iw Reach, ew Reach, DIMand, EssentialWhite, ew, icolor, icolor Cove, IntelliWhite, iw, iplayer, Optibin, and Powercore are either registered trademarks or trademarks of Philips Solid-State Lighting Solutions, Inc. in the United States and / or other countries. All other brand or product names are trademarks or registered trademarks of their respective owners. Due to continuous improvements and innovations, specifications may change without notice. DAS R

10 TYPE JOB NAME 8200 SERIES RGB YOKE MOUNT 72LED LUMINAIRE DMX COLOR CHANGING DESCRIPTION The 8200 Series is a high performance compact precision LED lighting system that provides consistent styling with a variety of light distributions. Multiple LED optical systems provide a wide range of precise light control and an array of mounting accessories are available to suit almost any application. This unit uses a red, green, and blue (RGB) LED array to create DMX controlled color-changing lighting effects. Color control is achieved through four channels per fixture, using either the Easyl from Acuity Brands or any standard DMX512 hardware, at a maximum of 44 frames per second. All channels have logarithmic power for finer color and intensity control. The fourth channel (Intensity), allows the user to vary brightness without affecting the color. Features & Specifications MATERIAL: Die Cast Copper Free Aluminum (A360) Housing and Doors. LED: RGB LED array, 110 input watts max. Lumen maintenance of individual light sources has been independently tested using IESNA LM80 standards. LIGHT DISTRIBUTIONS: See ordering guide LENS: Flat tempered glass for maximum resistance to impact. GLARE CONTROL: External Glare Control options include Barn Doors, Full and Half Glare Shields. MOUNTING: Aluminum yoke & stainless steel locking hardware allows fixture head to be easily aimed and fixed in place. Fixtures are provided with 10 of 16/3 ST-W cord for supply method and 10 DMX data cable. CONTROL/POWER SUPPLY: MVOLT ( ) LED power supply. Control uses either the Easyl from Acuity Brands or any standard DMX512 hardware, 3 or 4 channels available: - 3 channel = Red, Green, Blue - 4 channel = Red, Green, Blue, and Intensity COMMUNICATION TO FIXTURE: DMX512 Direct FINISH: Textured TGIC powder coat polyester finish (see ordering guide for available colors) PART NUMBER MODEL MOUNTING ACCESS. LAMP TYPE LED COLOR VOLTAGE DISTRIBUTION MOUNTING ACCESSORIES OPTIONS DRIVE CURRENT LAMP FINISH LISTING: CSA, CSA US WEIGHT: 54 lbs. APPROVALS EPA: 2.10 ft Acuity Brands Lighting, Inc. 2/13/ _YM_COLORCHANGING LED NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) Nordhoff St., Suite B Chatsworth, CA Phone: Fax:

11 8200 YM RGB LED ORDERING INFORMATION 50/60 Hz Application Choose the boldface catalog nomenclature that best suits your needs. PART NO. EXAMPLE: LED RGB MVOLT WFL YM 3DMX SQ5 LP BL Model* 8200 Lamp Type* 72LED LED Color* RGB Voltage* MVOLT ( Volt) Distribution* Mounting* Flood Lights YM Yoke Mt NSP Nar. Spot NFL Nar. Flood FL Flood WFL Wide Flood VWFL Very Wide Flood HSP Horizontal Spot MFL Medium Flood Mount. Accessories PMT 2 Pole Mount Tee SMSA Stan. Mount Splice Access. Available in 6 increments PSSA Ped. Stanchion Splice Access SMT 2 Stanchion Mount Tee EWM_ Ext. Wall Mount Available in 6 increments PMSA Pole Mount PAR4/_ 3 PAR5/_ 3 PAR6/_ 3 PAS4/_ 3 PAS5/_ 3 PAS6/_ 2,3 PATR4/_ 2,3 PATR5/_ 2,3 PATR6/_ 2,3 PATS4/_ 2,3 PATS5/_ 2,3 PATS6/_ 2,3 Pole Arm Round, 4 diam. Pole Arm Round, 5 diam. Pole Arm Round, 6 diam. Pole Arm Square, 4 diam. Pole Arm Square, 5 diam. Pole Arm Square, 6 diam. Pole Arm Tee Round, 4 diam. Pole Arm Tee Round, 5 diam. Pole Arm Tee Round, 6 diam. Pole Arm Tee Square, 4 diam. Pole Arm Tee Square, 5 diam. Pole Arm Tee Square, 6 diam. Control 3-Channel 3DMX DMX Channel 4DMX DMX 512 Accessories External 1 BD Barn Doors FGS Full Glare Shield HGS Half Glare Shield WRG Wire Rock Guard Channel Prog. * ST_ 4 Static SQ_ 5 Sequential CCHAN 6 Custom Channels Consult Factory LP Lamp* LED Array Finish* BL Black BZ Bronze DDB Dark Bronze DNA Natural Alum. GN Green GR Gray SND Sand STG Steel Gray TVG Terra Verde Green WH White CF Custom Finish *Indicates required selection. Notes: 1 Each option is mutually exclusive, choose one only. 2 Requires (2) two fixtures per mounting. 3 Available in 6 increments from 12 to 24, specify length. 4 Static Channels - All fixtures have the same channel numbers. Indicate starting channel. 5 Sequential channels - specify starting channels. 6 Consult Factory EASYL DMX controller purchased separately, see for details WARRANTY Five year limited warranty. Full warranty terms located at and_conditions.aspx 2013 Acuity Brands Lighting, Inc. 2/13/ _YM_COLORCHANGING LED NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) Nordhoff St., Suite B Chatsworth, CA Phone: Fax:

12 TYPE JOB NAME 8200 SERIES 108LED MONOCHROMATIC YOKE MOUNT PART NUMBER MOUNTING MODEL ACCESSORIES LAMP TYPE LED COLOR VOLTAGE DISTRIBUTION OPTIONS DRIVE CURRENT LAMP FINISH DESCRIPTION The 8200 Series is a high performance compact precision LED lighting system that provides consistent styling with a variety of light distributions. Multiple LED optical systems provide a wide range of precise light control and an array of mounting accessories are available to suit almost any application. Features & Specifications MATERIAL: Die Cast Copper Free Aluminum (A360) Housing and Doors. LED: Monochromatic LEDs, 259W Max. LIGHT DISTRIBUTIONS: NEMA Flood (2x2 through 7x7), Horizontal Spot (4x2). LENS: Flat tempered glass for maximum resistance to impact. GLARE CONTROL: External Glare Control options include Barn Doors, Full and Half Glare Shields. MOUNTING: Aluminum yoke & stainless steel locking hardware allows fixture head to be easily aimed and fixed in place. Fixtures are provided with 6 of 16/3 ST-W cord for supply method. POWER SUPPLY: MVOLT ( ), 347 or 480 Volt LED power supply. FINISH: Textured TGIC powder coat polyester finish (see ordering guide for available colors) Salt Spray. LISTING: CSA, CSA US WEIGHT: 58 lbs. EPA: 2.10 ft 2 APPROVALS 2013 Acuity Brands Lighting, Inc. 2/26/ YM 259W LED NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) Nordhoff St., Suite B Chatsworth, CA Phone: Fax:

13 8200 YM 259W LED ORDERING INFORMATION 50/60 Hz Application Choose the boldface catalog nomenclature that best suits your needs. PART NO. EXAMPLE: LED WHT53K MVOLT NSP YM SMSA18 700MA LP BL Model* 8200 Lamp Type* 108LED 259 watts LED Color* WHT30K White WHT41K White WHT53K White Voltage* MVOLT ( Volt) 347L 347 Volt 480L 480 Volt Distribution* Mounting* Flood Lights YM Yoke Mt NSP Nar. Spot NFL Nar. Flood FL Flood WFL Wide Flood VWFL Very Wide Flood HSP Horizontal Spot MFL Medium Flood Mount. Accessories PMT 3 Pole Mount Tee SMSA Accessories External 1 BD Barn Doors FGS Full Glare Shield HGS Half Glare Shield WRG Wire Rock Guard Safety LASC Safety Cable Stan. Mount Splice Access. Available in 6 increments PSSA Ped. Stanchion Splice Access SMT 3 Stanchion Mount Tee EWM_ Ext. Wall Mount Available in 6 increments PMSA Pole Mount PAR4/_ 4 Pole Arm Round, 4 diam. PAR5/_ 4 Pole Arm Round, 5 diam. PAR6/_ 4 Pole Arm Round, 6 diam. PAS4/_ 4 Pole Arm Square, 4 diam. PAS5/_ 4 Pole Arm Square, 5 diam. PAS6/_ 4,5 Pole Arm Square, 6 diam. PATR4/_ 3,4 Pole Arm Tee Round, 4 diam. PATR5/_ 3,4 Pole Arm Tee Round, 5 diam. PATR6/_ 3,4 Pole Arm Tee Round, 6 diam. PATS4/_ 3,4 Pole Arm Tee Square, 4 diam. PATS5/_ 3,4 Pole Arm Tee Square, 5 diam. PATS6/_ 3,4 Pole Arm Tee Square, 6 diam. Options Photo Control PER 2 Photo Cell Receptacle Drive Current* 350ma 350 milli-amps 700ma 700 milli-amps (standard) Dimming LDIM V Dimming (25% reduction) Lamp* LPI LED Array Included Finish* BL Black BZ Bronze DDB Dark Bronze DNA Natural Alum. GN Green GR Gray SND Sand STG Steel Gray TVG Terra Verde Green WH White CF Custom Finish *Indicates required selection. Notes: 1 Each option is mutually exclusive, choose one only. 2 Nema twist-lock receptacle only. Photo cell control by others, PER option not IP Rated 3 Requires (2) two fixtures per mounting. 4 Available in 6 increments from 12 to 24, specify length. 5 Only available with 700 ma Acuity Brands Lighting, Inc. 2/26/ YM 259W LED NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) Nordhoff St., Suite B Chatsworth, CA Phone: Fax:

14 LED Light Engine Kelvin Temp MH Equivalent Number of LEDs Drive Current Initial Lumens 2 Input Watts Lumens Per Watt REBEL REBEL REBEL REBEL REBEL REBEL 3000K 4100K 5300K 3000K 4100K 5300K 150W 250W 250W 250W 400W 400W mA 350mA 350mA 700mA 700mA 700mA ,000 13, CRI LED LIFE: OPERATING TEMPERATURE: L70/65,000 Hours -30 C through 40 C Notes: * MH Equivalencies are approximate and vary by distribution. 2 Initial Lumens will vary depending on distribution, consult individual IES files for exact data Acuity Brands Lighting, Inc. 2/26/ YM 259W LED NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) Nordhoff St., Suite B Chatsworth, CA Phone: Fax:

15 D.C. Department of Transportation Bridge Façade Lighting Study Prepared By: Johnson, Mirmiran and Thompson, Inc. Appendix B Data Enabler Pro DMX Controls Francis Scott Key Bridge February 24, 2014

16 Date: Type: Firm Name: Project: Data Enabler Pro Integrated data and power for intelligent LED lighting fixtures employing Powercore technology Data Enabler Pro Integrated data and power for intelligent LED lighting fixtures using Powercore D For information on installation planning, including electrical and data configuration guidelines, view or download the Data Enabler Pro Product Guide from dataenablerpro/ Data Enabler Pro delivers integrated data and power to intelligent color and tunable white LED lighting fixtures employing Powercore technology from Philips Color Kinetics. Data Enabler Pro integrates many of the features of the previous generation of Data Enablers, including Data Enabler DMX, Data Enabler Ethernet, and Data Enabler EO. Data Enabler Pro is the single solution for all intelligent Powercore-based installations, whether DMX or Ethernet, color or white, indoors or outdoors. Easy installation Accessible, clearly labeled terminal block connectors for DMX, Ethernet, line voltage, and fixtures make installation easy. Tethered cover with captive screws ensures convenient removal and replacement. Controller Keypad Ser iplayer 3 Controller VAC VAC ial C able Data Enabler Pro DM XD ata Junction Box Light System Manager Controller Supports fixtures employing Powercore technology Powercore technology rapidly, efficiently, and accurately controls power output to LED lighting fixtures directly from line voltage. Philips Data Enabler Pro merges line voltage and control data and delivers them to Powercore fixtures over a single cable, dramatically simplifying installation and lowering total system cost. On-board diagnostics On-board indicator LEDs provide visual feedback for normal operation, Ethernet connection detection, and Ethernet and DMX data transmission. Full support for DMX and Ethernet Provides inputs and outputs for both DMX and Ethernet, allowing you to connect multiple Data Enabler Pro devices in series. Also provides an Ethernet output terminal for ew Accent MX Powercore and icolor Accent MX Powercore support. DMX Configuration Ethernet Controller Keypad Ethernet Switch CCAA TT 5 e CC VAC aabble le Eth ern Data Enabler Pro et D ata Junction Box Ethernet Configuration Outdoor-rated for use in damp and wet environments Data Enabler Pro offers superior leakage protection in a cast aluminum, IP66-rated enclosure. Multiple conduit entries Data Enabler Pro conduit entries accommodate NPT conduit in US trade sizes of 1/2 in and 3/4 in, or metric sizes of PG13 and PG21. Universal power input range Data Enabler Pro automatically senses mains voltages ranging from VAC, and passes mains voltages through to all connected lights. Designed for maximum energy efficiency Data Enabler Pro consumes just 20 W maximum. Optional power-saving modes automatically cut power to attached lights when lights are off for a configurable number of minutes.

17 DESIGNEDAND DEVELOPED IN THE USA. MADE IN CHINA. Specifications Due to continuous improvements and innovations, specifications may change without notice. Item Specification Details Electrical Connections Physical Input Voltage Maximum Input Current Power Consumption Load Current Power Input Power / Data Output DMX Input / Output Ethernet Input / Output Dimensions (Height x Width x Depth) Weight Construction Finish Threaded Openings Temperature Ranges Humidity Cooling Heat Dissipation Data Input Source VAC*, auto-ranging, 50 / 60 Hz 16.5 A maximum 20 W maximum 16 A maximum 3-wire PC terminal block connector 4-wire PC terminal block connector 4-wire IDC terminal block connector (ew Accent MX Powercore and icolor Accent MX Powercore only) Double-pair, double-entry IDC connectors 9.6 in Double-pair, double-entry IDC connectors 244 mm 3.4 x 10.5 x 5.4 in (87 x 267 x 138 mm) 5.4 lb (2.4 kg) Cast aluminum enclosure with slots for surface mounting Powder-coated industrial gray matte 3/4 in NPT for power / 1/2 in NPT for data (US trade) PG21 for power / PG13 for data (metric) F ( C) Operating F ( C) Startup 10.5 in 267 mm F ( C) Storage Certification Certification UL / cul, FCC Class A, CE, C-Tick and Safety Environment 3.4 indry / Damp / Wet Location, IP66 87 mm * Verify that the line voltage is appropriate for the lighting fixtures in your installation. See a specific fixture s documentation for supported line voltages. PC terminal block connectors accept recommended wire sizes from 8 18 AWG ( mm 2 ). 1.6 in 41 mm IDC connectors accept wire sizes from AWG ( mm 2 ). KiNET is the Ethernet lighting protocol from Philips Color Kinetics. 1.7 in 43 mm 6.35 in mm 3.4 in 87 mm 2.35 in 60 mm 3 mm hex 0 95%, non-condensing.8 in Ø (UL) 1.05 in Ø (UL) Convection Accepts ½ in NPT Accepts ¾ in NPT 20.4 mm Ø (CE) 26.8 mm Ø (CE) 20 W Accepts M20 Accepts M25 Philips full range of controllers, third-party 8.7 in DMX 267 mm controllers, or KiNET-compatible third-party Ethernet controllers.8 in Ø (UL) Accepts ½ in NPT 20.4 mm Ø (CE) Accepts M in 71 mm.1875 in Ø 4.8 mm 1.6 in 41 mm Data Enabler Pro Data Enabler Pro www. w. colorkinetics.com 9.6 in 244 mm 10.5 in 267 mm 8.7 in 267 mm 1.7 in 43 mm 5.4 in 138 mm 6.35 in mm 1.05 in Ø (UL) Accepts ¾ in NPT 26.8 mm Ø (CE) Accepts M in 60 mm 3 mm hex 2.8 in 71 mm.1875 in Ø 4.8 mm Ordering Information Item Type Item Number Philips 12NC 3/4 in / 1/2 in NPT (US trade size conduit) Data Enabler Pro PG21 / PG13 (metric size conduit) Use Item Number when ordering in North America. Philips Color Kinetics 3 Burlington Woods Drive Burlington, Massachusetts USA Tel Tel Fax Copyright Philips Solid-State Lighting Solutions, Inc. All rights reserved. Chromacore, Chromasic, CK, the CK logo, Color Kinetics, the Color Kinetics logo, ColorBlast, ColorBlaze, ColorBurst, ew Fuse, ColorGraze, ColorPlay, ColorReach, iw Reach, ew Reach, DIMand, EssentialWhite, ew, icolor, icolor Cove, IntelliWhite, iw, iplayer, Optibin, and Powercore are either registered trademarks or trademarks of Philips Solid-State Lighting Solutions, Inc. in the United States and / or other countries. All other brand or product names are trademarks or registered trademarks of their respective owners. Due to continuous improvements and innovations, specifications may change without notice. DAS R