Axial Piston Variable Pump A10VO

Transcription

1 Electric Drives and Controls Hydraulics inear Motion and Assembly Technologies Pneumatics ervice Axial Piston Variable Pump A10VO RA 92703/ /44 Replaces: Data sheet eries 52/53 ize Nominal pressure 3600 psi (250 bar) Peak pressure 4600 psi (315 bar) Open circuit eries 52 eries 53 Contents Ordering code - standard program 2 Hydraulic fl uids 4 Technical data 5 Operating curves for pumps with pressure control 8 DR - Pressure control 9 DRG - Pressure control, remote 10 DRF (DFR) and DR (DFR - pressure and fl ow control 11 A... - pressure, fl ow and power control 12 Unit dimensions, size Unit dimensions, size Unit dimensions, size Unit dimensions, size Unit dimensions, size Unit dimensions, size Combination pumps A10VO + A10V()O 36 Overview of through drive mounting options 36 Dimensions through drives 37 Installation notes 40 General information 44 Features Variable axial piston pump in swash plate design for hy dro - sta ti c drives in open circuits Flow is proportional to drive speed and displacement. The fl ow is infi nitely variable by adjustment of the swash plate. trong bearings for long service life High permissible drive speeds High power to weight ratio mall dimensions ow noise level Good suction characteristics Axial and radial loading of drive shaft possible Pressure and fl ow control Electro-hydraulic pressure control Power control Electro-proportional displacement control hort response times

2 2/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Ordering code - standard program A10V() O / 5 V Axial piston unit wash plate design, variable A10V Nom. pressure 3600 psi (250 bar), peak pressure 4600 psi (315 bar) A10V Operating mode 02 Pump, open circuit O ize ~displacement V g max in in (cm 3 ) (10) (18) (28) (45) (63) (85) Control devices Pressure control DR DR with hydraulic fl ow control -T open D F R DFR -T open DR F DRF -T closed DFR1 DFR1 -T closed DR DR with fl ow control, electro-hydraulic adjustment of differential pressure (inverse proportional characteristic), (RA ) EF. D. EF.D. with remote pressure control hydraulic DR G DRG electric, inverse characteristic ED. ED. 04 Power control with pressure control minimum start of control 145 to 510 psi (10 to 35 bar) A 5 D A5D 520 to 1015 psi (36 to 70 bar) A 6 D A6D 1030 to 1520 psi (71 to 105 bar) A 7 D A7D 1535 to 2030 psi (106 to 140 bar) A 8 D A8D 2045 to 3335 psi (141 to 230 bar) A 9 D A9D with remote pressure control min. start of control see above A D G ADG with pressure and fl ow control, -T closed min. start of control see above A D AD with press. and fl ow controlol electr. adjustment of diff. press. (inverse prop. characteristic), -T closed (RA ) min. start of control see above A. A. Electro-proportional displacement control (RA ) with pressure and fl ow control, positive characteristic EP. D. EP.D. with pressure and fl ow control, positive characteristic; deactivation of control at I = 0 EK. D. EK.D. eries 05 5 For availability of control options in series 52 and 53 see index 06 in ordering code

3 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 3/44 A10V() O / 5 V Index DR, DFR, DFR1, DRG, ED 2 DR, DRF, DR, DRG, ED... 3 EF..., A..., EP..., EK... 3 Direction of rotation 07 viewing on shaft end right hand R left hand eals 08 FKM (fl uor-rubber) V haft end plined shaft to AE J744, standard shaft imilar to shaft however for higher input torque R 09 plined shaft to AE J744, reduced diameter, not for through drive U imilar to shaft U higher input torque, not for through drive W Parallel shaft AE with key K 2) Tapered with Woodruff key C 2) 10 Mounting flange AE 2-hole C AE 4-hole D Port for service lines AE fl ange at rear, UNC fi xing thread(no through drive) AE fl ange on side-opposite sides, UNC fi xing thread 62 (for through drive) Threaded ports at rear, UNC threads (no through drive) 64 2) 12 Through drive Without through drive (standard for version 61 and 64) N00 Flange AE J744 Coupler for splined shaft 3) ealing 82-2 (A) 5/8 in 9T 16/32DP axial K (A) 3/4 in 11T 16/32DP axial K () 7/8 in 13T 16/32DP axial K () 1 in 15T 16/32DP axial K (C) 1 1/4 in 14T 12/24DP axial K (C) 1 1/4 in 14T 12/24DP axial K (C) 1 1/2 in 17T 12/24DP axial K24 Not for new projects. For new projects use only series 53. 2) only eries 52 3) 30 pressure angle, fl at base, fl ank centering, fi t class 5 available in preparation not available

4 4/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Hydraulic fl uids Prior to project design, please see our technical data sheets RE (mineral oil), RE (environmentally acceptable fl uids) and RE (HF-fl uids) for detailed information on fl uids and operating conditions. When using HF- or environmentally acceptable fl uids attention must be paid to possible limitations of the technical data, if necessary contact us. (when ordering please state in clear text the fl uid to be used). Operation on kydrol is only possible after consultation with us. Operating viscosity range For optimum effi ciency and service life we recommend that the operating viscosity be chosen in the range of: ν opt = opt. operating viscosity U ( mm 2 /s) referred to tank temperature (open circuit). imit of viscosity range For critical operating conditions the following values apply: ν min = 60 U (10 mm 2 /s) for short periods (t 1 min) at max. permissible leakage fl uid temperature of 239 F (115 C). Please note, that the max fl uid temperature of 239 F (115 C) is also not exceeded in certain areas (for instance bearing area) The fl uid temperature in the bearing area is approx. 7 F (5 K) higher than the average leakage fl uid temperature. ν max = 7500 U (1600 mm 2 /s) for short periods (t 1 min) on cold start (t min = p 435 psi (30 bar), n 1000 rpm, -13 F (-25 C)) At temperatures between -13 F (-25 C) and -40 F (-40 C) special measures may be required, depending on installation conditions. Please consult us for further information. For detailed information on operation with low temperatures see data sheet RE election diagram Viscosity ν [mm 2 /s] F C VG 68 VG 46 VG 32 VG 22 VG Notes on the selection of the hydraulic fluid In order to select the correct fl uid, it is necessary to know the operating temperature in the tank (open circuit) in relation to the ambient temperature. The fl uid should be selected so that within the operating temperature range, the viscosity lies within the optimum range (ν opt ), see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case. Example: at an ambient temperatue of F ( C) the operating temperature in the tank is 140 F (60 C). In the optimum viscosity range (ν opt ; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; VG 68 should be selected Important: The leakage fl uid (case drain fl uid) temperature is infl uenced by pressure and input speed, and is always higher than the tank temperature. However, at no point in the circuit may the temperature exceed 239 F (115 C). If it is not possible to comply with these conditions because of extreme operating parameters or high ambient temperatures, please consult us. Filtration of fluid The fi ner the fi ltration the better the achieved cleanliness of the hydraulic fl uid and the longer the life of the axial piston unit. To ensure a reliable functioning of the axial piston unit, a minimum cleanliness of 20/18/15 to IO 4406 is necessary. At very high operating temperatures (195 F (90 C) to max. 239 F (115 C)) a cleanliness of 19/17/14 to IO 4406 is necessary. If above mentioned grades cannot be maintained please consult us ν opt U mm 2 /s mm 2 /s C F Temperature range t in C t min = -40 F (-40 C) Fluid temperature range U 42 t max = 240 F (115 C)

5 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 5/44 Technical data Operating pressure range Inlet Absolute pressure at port p abs min 12 psi (0,8 bar) p abs max 73 psi (5 bar) To determine the min. required inlet pressure p abs at inlet port or the reduction of displacement at higher input speeds see the diagram to the right. Outlet Pressure at port Nominal pressure p N 3600 psi (250 bar) Peak pressure p max 4600 psi (315 bar) (Pressures to DIN 24312) Direction of flow to. Maximum permissible speed (peed limit) Permissible speed by increase of inlet pressure p abs at the inlet port or reduction of displacement (V g V g max ). peed n/n 0 max [rpm] Displacement V g /V g max [in 3 (cm 3 )] (1.2) 14.5 (1.0) 13 (1.6) (1.4) (0.9) 11.5 (0.8) Inlet pressure p abs [psi (bar)] Case drain pressure Maximum permissible case drain pressure (port, 1/2 ): maximum 7 psi (0,5 bar) higher than the inlet pressure at port, however not higher than 29 psi (2 bar) absolute. p abs max 29 psi (2 bar)

6 6/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Technical data Table of values (theoretical values, without considering effi ciencies and tolerances; values rounded) ize A10V()O Displacement V g max in 3 (cm 3 ) 0.64 (10,5) 1.10 (18) 1.71 (28) 2.75 (45) 3.84 (63) 5.18 (85) peed max. at V g max n 0 max rpm ) max. at V g < V g max n 0 max zul rpm Flow at n 0 max q V0 max gpm (/min) 9.7 (37) 15.6 (59) 22 (84) 31 (117) 43 (163) 55 (212) at n E =1500 min -1 q VE max gpm (/min) 4 (15) 7.1 (27) 11.1 (42) 18 (68) 25.1 (95) 34 (128) Power Δp = 3600 psi (250 bar) at n 0 max P o max HP (kw) 22 (16) 34 (25) 47 (35) 65 (49) 90 (68) 119 (89) at n E =1500 min -1 P E max HP (kw) 9.4 (7) 15 (1 24 (18) 38 (28) 52 (39) 71 (53) Torque at V g max Δp = 3600 psi (250 bar) T max lb-ft (Nm) 31 (42) 52 (7 82 ( (179) 184 (250) 247 (338) Δp = 1440 psi (100 bar) T lb-ft (Nm) 13 (17) 21 (29) 33 (45) 53 (72) 74 (100) 102 (135) Torsional stiffness haft c lb-ft/rad (Nm/rad) 6760 (9200) 8082 (11000) (22300) (37500) (65500) (143000) haft R c lb-ft/rad (Nm/rad) (14800) (26300) (41000) (69400) haft U c lb-ft/rad (Nm/rad) 5020 (6800) 5870 (8000) (30000) (49200) (102900) haft W c lb-ft/rad (Nm/rad) (34400) (54000) (117900) haft K/C c lb-ft/rad (Nm/rad) 7965 (10800) (26800) (43900) (73900) Moment of inertia rotary group J TW lbs-ft 2 (kgm 2 ) (0,0006) (0,00093) (0,0017) (0,0033) (0,0056) (0,012) Angular acceleration, max. 3) α rad/s Fill volume V gal () 0.05 (0,2) 0.06 (0,25) 0.08 (0,3) 0.13 (0,5) 0.21 (0,8) 0.26 ( Weight approx. (without fl uid) m lbs (kg) 17 (8) 25 (11,5) 31 (14) 40 (18) 48.5 (22) 75 (34) Values are valid with inlet pressure of 15 psi (1 bar) at suction inlet. With reduced displacement or increased inlet pressure the drive speed can be increased according to the diagram on page 5. 2) For higher drive speeds please consult us. 3) These values are valid for conditions between the min. required and the max. permissible drive speeds. For external sources of excitation (eg. diesel engine 2-8 fold rotary frequency, cardan shaft 2 fold rotary frequency). The limit is valid for a single pump. The load carrying capacity of the connecting parts must be taken into consideration. Caution: Exceeding these limits can lead to a loss of operability, reduction of service life or complete destruction of the axial piston unit. The permissible values can be calculated.

7 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 7/44 Technical Data Determination of pump size Flow q V = Torque T = Power P = V g n η V V [gpm (/min)] g = geometr. displacement per revolution in in 3 (cm 3 ) 231 (1000) p = pressure differential in psi (bar) V g Δp n = drive speed in rpm [lb-ft (Nm)] 24 (20) π η mh η V = volumetric effi ciency 2π T n q = V p η [HP (kw)] mh = mechanical-hydraulic effi ciency 33,000 (60000) 1,714 (600) η t η t = overall effi ciency (η t = η V η mh ) Permissible radial and axial forces on drive shaft ize Radial force, max. Fq at F q max lbf /2 /2 /2 (N) (250) (350) (1200) (1500) (1700) (2000) Axial force, max. F ax N 90 ± Fax (400) 157 (700) 225 (1000) 337 (1500) 450 (2000) 675 (3000) Permissible input and through drive torques ize Torque, max. (at V g max and Δp = 3600 psi (250 bar )) T max lb-ft (Nm) 31 (42) 52 (7 82 ( (179) 184 (250) 249 (338) Input torque, max. 2) for shaft end T E zul lb-ft (Nm) 93 (126) 91 (124) 146 (198) 235 (319) 465 (630) 851 (1157) AE J744 3) in 3/4 3/4 7/ /4 1 1/2 for shaft end R T E zul lb-ft (Nm) 110 (150) 166 (225) 295 (400) 479 (650) AE J744 3) in 3/4 7/ /4 for shaft end U T E zul lb-ft (Nm) 44 (60) 43 (59) 139 (188) 226 (306) 463 (628) AE J744 3) in 5/8 5/8 7/ /4 for shaft end W T E zul lb-ft (Nm) 162 (220) 292 (396) 447 (650) AE J744 3) in 7/ /4 for shaft end K T E zul lb-ft (Nm) 78 (106) 107 (145) 156 (212) 325 (44 in (mm) (19.05) (22.225) (25.4) (31.75) for shaft end C 4) T E zul lb-ft (Nm) 107 (145) 156 (212) 325 (44 Through drive torque, max. for shaft end T D zul lb-ft (Nm) 80 (108) 118 (160) 235 (319) 357 (484) 515 (698) for shaft end R T D zul lb-ft (Nm) 89 (120) 130 (176) 270 (365) 357 (484) without considering effi ciency 2) for shaft without side load 3) (ANI 92.1a-1996) 4) only for series 52 Distribution of torques T E T 1 T 2 1. Pumpe 1. Pump 2. Pumpe T D

8 8/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Operating curves for pumps with pressure control Drive power and flow (Fluid: mineral oil to IO VG 46 DIN 51519, t = 122 F (50 C)) ize 10 n = 1500 rpm n = 3600 rpm Flow q V ize 18 n = 1500 rpm n = 3600 rpm Flow q V gpm gpm (/min) (35) (25) (15) (5) (/min) (60) (50) (40) (30) (20) 0 q V ize 28 n = 1500 rpm n = 3000 rpm Flow q v 0 gpm (/min) 23.8 (90) 20 (80) 15 (60) (40) (20) 0 p qv min p qv max (kw) HP 30 (20) 25 (15) 20 (10) (5) 5 0 (50) (100) (150) (200) (250) (bar) psi Operating presure p (kw) HP q V (40) (30) (20) p qv max p qv min (10) 20 (0) 0 (50) (100) (150) (200) (250) (bar) psi Operating presure p (kw) HP (40) 60 q v P qv max (30) 40 (20) P qv min (10) 20 0 (50) (100) (150) (200) (250) (bar) psi Operating pressure p Drive power P q V Drive power P q V Drive power Pqv ize 45 n = 1500 rpm n = 2600 rpm Flow q v gpm (/min) (120) 30 (100) (80) 15 (60) (40) (20) ize 63 n = 1500 rpm n = 2700 rpm Flow q v (40) (20) ize 85 n = 1500 rpm n = 2500 rpm Flow q V 0 gpm (/min) 40 (160) 35 (140) 30 (120) 25 (100) 20 (80) 15 (60) 0 gpm (/min) 58 (220) 55 (200) (180) (160) (140) (120) (100) (80) (60) (40) (20) 0 (kw) HP (60) 80 q (50) v P qv (40) max 60 (30) 40 (20) P qv min (10) 20 0 (50) (100) (150) (200) (250)(bar) psi Operating pressure p q v P qv max P qv min (40) (30) (20) (10) (50) (100) (150) (200) (250) (bar) psi Operating pressure p q V p qv max p qv 0 Drive power Pqv (kw) HP (80) 100 (70) (60) 80 (50) (90) (80) (70) (60) (50) (40) (30) (20) (10) Drive power Pqv (kw) HP (110) (100) 0 (50) (100) (150) (200) (250) (bar) Operating pressure psi Drive power P q V Overall efficiency Volumetric efficiency η t = q V p P pv max 600 η V = q V q V theor

9 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 9/44 DR - Pressure control The pressure control serves to maintain a constant pressure in the hydraulic system, within the control range of the pump. The pump therefore supplies only the amount of hydraulic fl uid required by the actuators. The pressure can be steplessly set at the pilot valve. tatic characteristic at n 1 = 1500 rpm; t fl uid = 120 F (50 C) psi (bar) 3625 (250) Operating pressure p [bar] 290 Adjustment range (20) min setting range Flow q V [gpm (/min)] max Hysteresis and pressure rise Δp max 58 psi (4 bar) chematic: DR 1 2 Dynamic characteristic The curves show average measured values under test conditions. Conditions: n = 1500 rpm t fl uid = 120 F (50 C) ine main relief set at 4570 psi (315 bar) tepped loading by suddenly opening or closing the pressure line using a pressure relief valve at 3.3 ft (1 m) downstream from the pump pressure outlet. Operating pressure p psi Displacement (swivel angle) (bar) (315) (300) (250) (200) (150) (100) (50) V g max V g min Ports Outlet port Inlet port, 1/2 Case drain port ( 1/2 plugged) Control data Hysteresis and repeatability Δp max. 45 psi (3 bar) Pilot fl uid consumption max. approx. 0.8 gpm (3 /min) Flow loss at q V max see page 8 Control times ize t A [ms] against 725 psi (50 bar) t A [ms] against 3200 psi (220 bar) t E [ms] standby psi (250 bar) Control time de-stroking time t E stroking time t A

10 10/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 DRG - Pressure control, remote The DRG-control valve enables a remote setting of max. pump pressure below the setting of the DR-, control spool, see page 9. chematic: DRG not included in supply For the remote setting of pressure it is necesary to pipe an external relief valve to port. This valve is not included in the supply of the pump. The differential pressure at the DRG-spool is set as standard to 290 psi (20 bar), and this results in a pilot fl ow of approx. 0.4 gpm (1,5 /min). If another setting is required(range between 145 and 320 psi (10 and 22 bar)), please state in clear text. As a separate pressure relief valve we can recommend: DDH 6 (hydraulic) to RE or DETR -O381 with orifi ce dia inch (0,8mm) in P (electric) to RE The max. lenght of piping should not exceed 6.6 ft (2 m). Control data ee page 9 2 Ports Outlet port Inlet port, 1/2 Case drain ports ( 1/2 plugged) Pilot pressure port

11 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 11/44 DRF (DFR) and DR (DFR - pressure and fl ow control Execution of control valve as described on page 9 and 10. In addition to the pressure control function, the pump fl ow to the actuator may be varied by means of a differential pressure (eg. over an orifi ce or a directional valve). The pump supplies only the amount of fl uid as required by the actuator. The pressure control overrides the fl ow control function. The DR (DFR has no connection between -port and Tank. tatic characteristic Flow control at n 1 = 1500 rpm; t fl uid = 120 F (50 C) Operating press. p [bar] psi (bar) 3625 (250) 290 Displacement V g (%) etting range (20) min tatic characteristic at variable speed 100 Flow q V Control times stroking time t A max Flow q V [/min] peed n (bar) psi (315) 4570 (250) 3620 (200 de-stroking time t E (100) 1450 (50 (18) Control time (stand by) Δq V (see table) 2900 ( Δp V see table of values Dynamic characteristic of flow control The curves are measured average values under test conditions t A [ms] t E [ms] t E [ms] ize stand by psi 3600 psi (250 bar) 725 psi (50 bar) (250 bar) - stand by - stand by oad pressure p chematic: DRF (DFR) 2 1 Ports Outlet port Inlet port, 1 Case drain ports ( 1 plugged) Pilot pressure port closed in DR or (DFR valve not included in supply Differential pressure Δp tandard setting: 200 psi (14 bar). If a different setting is required please state in clear text. When port is unloaded to tank (and outlet is closed) a zero stroke pressure ("standby") of p = 260 ± 30 psi (18 ± 2 bar) results (depends on Δp-setting). Control data For pressure control see page 9. Max. fl ow deviation (hysteresis and rise) measured at a drive speed of n = 1500 rpm. ize Δqv max gpm (0,5) (0,9) (1,0) (1,8) (2,5) (3, (/min) Pilot fl uid consumption DRF (DFR) max. approx gpm (3...4,5 /min) Pilot fl uid consumption DR (DFR max. approx. 0.8 gpm (3 /min) Flow loss at q Vmax see page 8 Possible control valves to be used on (not included in supply of pump) -Mobile control valves Mobile valve block M4-12 (RE 64278) Mobile valve block M4-15 (RE 64282) UDV-Mobile control valves Mobile valve block M6-15 (RE 64284) Mobile valve block M7-22 (RE 64287)

12 12/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 A... - pressure, fl ow and power control Execution of pressure control like DR(G), see pages 9/10. Execution of pressure and fl ow control like DR, see page 11. In order to achieve a constant drive torque with varying operating pressures, the swivel angle and with it the output fl ow of the pump, is varied in such a manner, that the product of fl ow and pressure remains constant. Flow control is possible below the limit of the power curve. When ordering please state the max. input torque in clear text. Control data For technical data of pressure control see page 9. For technical data of pressure and fl ow control see page 11. Pilot fl uid consumption max. approx. 0.8 gpm (3,0 /min) Flow loss at q V max see page 8 tart of control (psi (bar)) 145 to 510 (10 to 35) 520 to 1015 (36 to 70) 1030 to 1520 (71 to 105) 1535 to 2030 (106 to 140) 2045 to 3335 (141 to 230) TorqueT [lb-ft (Nm)] ize (3,8-12, (6-19) (10-30) (15-43) (20-57) (12,2-23,3) (19,1-36) (30,1-59) (43,1-83) (57,1-112) (23,4-33,7) (36,1-52) (59,1-84) (83,1-119) (112,1-160) (33,8-45) (52,1-70) (84,1-112) (119,1-157) (160,1-212) (45,1-74,8) (70,1-117) (112,1-189) (157,1-264) (212,1-357) ordering code A5 A6 A7 A8 A9 tatic characteristic and torque curves psi (bar) p chematic: AD Operating Pressure p (300) (250) (200) A9 (150) A8 (100) A7 (50) A6 A q Δq V (see table page 1 chematic: ADG not included in supply T A9 chematic: AD Torque T [Nm] A8 A7 not included in supply A6 1 Ports Flow q V [%] A5 Outlet port Inlet port, 1, 2 Case drain ports ( 1, 2 plugged) pilot pressure port 2

13 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 13/44 Notes

14 14/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 10 A10VO10 DR/52R()-VC64N00 efore fi nalizing your design please 0.25 (6.4) Flange AE J (A) 2.87 (73) 0.43 ( (103) 0.35 (9) 2.11 (53.5) 2.20 (56) (Ø h8 ) Y 2.20 (56) max (110) DIA 0.43 (Ø DIA 0.94 (24) (148) 7.09 (180) View Y right hand rotation 4.19 (106.4) 5.28 (134) View Y left hand rotation haft ends pline shaft 3/4 in 11T 16/32DP (AE J (A-)) ø 3/4 in 1/4-20UNC (14) 0.87 ( (30) 1.50 (38) (28.6) (28.6) 2.00 ( (5 U pline shaft 5/8 in 9T 16/32DP (AE J (A)) (28.6) (28.6) 2.00 ( (5 DIA (2.5) 1.13 (28.6) (ø ) Centering 3) R 0.12x0.26 DIN (33) 0.31 (8) 1.61( (4.76 ) Ports Tightening torque, max. 2) Outlet port IO /16-12UNF-2; 0.79 (20) deep 261 lb-ft (360 Nm) Inlet port IO /16-12UNF-2; 0.79 (20) deep 261 lb-ft (360 Nm) / 1 Case drain port ( 1 plugged) IO /16-18UNF-2; 0.47 (12) deep 58 lb-ft (80 Nm) ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information 3) axial retention of coupling half eg. with clamp coupling or with clamping screw ø 5/8 in Centering 3) R 0.12x0.26 DIN (15.8) 0.94 (23.8) 1.25 (31.8) K Parallel keye shaft

15 3.248 DIA (ø h8 ) (53.5) 2.20 (56) DIA 0.43 (ø 1 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 15/44 Unit dimensions, size 10 A10VO10 DFR1(DFR, DRG)/52R()-VA64N00 efore fi nalizing your design please Flange AE J (A) 57.5 (146) 2.87 (73) 4.02 (102) 3.74 (95) 2.20 (56) 0.35 (9) max (110) 1.57 (40) Y (24) 5.83 (148) 7.09 (180) 4.19 (106.4) 5.28 (134) View Y right hand rotation View Y left hand rotation (28.6) (28.6) 2.00 ( ( (28.6) (28.6) 2.00 ( (5 haft ends see page 14 Ports Tightening torque, max. Outlet port IO /16-12UNF-2; 0.79 (20) deep 261 lb-ft (360 Nm) Inlet port IO /16-12UNF-2; 0.79 (20) deep 261 lb-ft (360 Nm) / 1 Case drain port ( 1 plugged) IO /16-18UNF-2; 0.47 (12) deep 58 lb-ft (80 Nm) Pilot pressure port IO /16-20UNF-2; (11.5) deep 29 lb-ft (40 Nm) see general information

16 16/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 18 A10VO18 DR/53R()-VC61N00 efore fi nalizing your design please 3.27 (83) 0.31 (7.8) 0.39 (10) 0.96 (24.5) 1 Flange AE J (A) (Ø82.55 h8 ) DIA Y 4.80 (122) 2.48 (63) 2.83 (72) (61.5) 0.1 (2.5) 2.42 (61.5) 0.43 ( (83) 6.14 (156) max (183) 4.20 (106.4) 5.35 (136) View Y port plate (58.7) 1.26 DIA (Ø32) 0.79 (Ø20) 1.87 (47.6) haft ends pline shaft 3/4 in 11T 16/32DP (AE J (A-)) 1.19 (30.2) 1.26 ocation of service ports for left hand rotation; turn port plate180 (32) R pline shaft 3/4 in 11T 16/32DP (AE J (A-)) U pline shaft 5/8 in 9T 16/32DP (AE J (A)) 0.87 (22.2) 1.10 (28) Ports ø 3/4 in 1/4-20UNC (14) 0.87 ( (30) 1.50 (38) ø3/4 in 1/4-20UNC-2 Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code (14) 0.83 ( (38) AE J518c IO 68 AE J518c DIN 13 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 2) 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1,2 Case drain ports ( 1,2 plugged) IO /4-16UNF lb-ft (160 Nm) ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information 3) axial retention of coupling half, eg. with clamp coupling or with clamping screw ø 5/8 in Centering 3) R 0.12x0.26 DIN (15.8) 0.94 (23.8) 1.25 (31.8)

17 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 17/44 Unit dimensions, size 18 A10VO18 DR (DRG, DRF)/53R()-VC62N00 efore fi nalizing your design please max (183) 4.45 (113) 3.27 (83) 0.31 (7.8) 0.39 (10) 0.96 (24.5) 1 Flange AE J (A) (Ø82.55 h8 ) DIA 1.26 DIA (Ø32) 2.31 (58.7) Y 4.80 (122) 2.48 (63) 2.83 (72) (61.5) 2.42 (61.5) ( (83) 1.19 (30.2) 5.63 (143) 6.70 (170) 4.19 (106.4) 5.35 (136) View Y port plate (62) View Z 4.17 (106) 0.79 DIA(Ø20) 1.87 (47.6) Z 0.87 (22.2) 2.22 (56.5) 2.22 (56.5) ocation of service ports for left hand rotation; turn port plate180 haft ends see page 16 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c DIN 13 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1,2 Case drain ports ( 1,2 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

18 18/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 18 A10VO18 AD/53R()-VC61N00 efore fi nalizing your design please 4.45 (113) 3.27 (83) 0.31 (7.8) 0.39 (10) 0.96 (24.5) 8.86 (225) Flange AE J (A) (Ø82.55 h8 ) DIA Y 4.80 (122) 4.45 (113) 2.48 (63) 2.83 (72) (61.5) (2.5) 2.42 (61.5) 0.43 ( (83) 6.14 (156) 4.19 (106.4) 5.35 (136) View Y port plate (62) 2.31 (58.7) 1.26 DIA (Ø32) 4.13 (105) 0.79 (Ø20) 1.87 (47.6) ocation of service ports for left hand rotation; turn port plate (30.2) 1.26 (32) 0.87 (22.2) 1.10 (28) haft ends see page 16 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c DIN 13 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1,2 Case drain ports ( 1,2 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5 deep) 29 lb-ft (40 Nm) see general information

19 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 19/44 Unit dimensions, size 18 A10VO18 AD/53R()-VC62N00 efore fi nalizing your design please 4.45 (113) 3.27 (83) 0.31 (7.8) 0.39 (10) 0.96 (24.5) 8.86 (225) 1 Flange AE J (A) DIA (Ø82.55 h8 ) (83) 1.19 (30.2) 5.63 (143) 6.69 (170) 1.26 (Ø32) 2.31 (58.7) Y 4.80 (122) 4.45 (113) 2.48 (63) 2.83 (72) 2 View Y Port plate (61.5) 4.19 (106.4) 5.35 (136) 2.42 (61.5) 2.44 (62) 0.10 (2.5) 0.43 (1 View Z 4.17 (106) 1.87 (47.6) 0.79 DIA (Ø20) Z 0.87 (22.2) 2.22 (56.5) 2.22 (56.5) ocation of service ports for left hand rotation; turn port plate180 haft ends see page 16 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c DIN 13 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1,2 Case drain ports ( 1,2 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5 deep) 29 lb-ft (40 Nm) see general information

20 (58.7) 1.26 DIA (ø32) 1.87 (47.6) 0.79 DIA (ø20) 20/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 28 A10VO28 DR/52R()-VC61(64) N00 efore fi nalizing your design please 3.54 (90) (ø101.6 h8 ) DIA 0.37 (9.5) 0.25 (6.3) 0.47 (12) 1 Y 4.86 (123.5) 2.87 (73) 2.60 (66) 2.72 (69) 0.56 (14.3) Flange AE J () 0.31 (7.9) 1.06 (27) 6.70 (170) max (209.5) 5.75 (146) 6.77 (172) View Y port plate 64 right hand rotation View Y port plate 61 right hand rotation 1.30 (33) 1.30 (33) ocation of service ports for left hand rotation; turn port plate (30.2) 1.30 (33) 0.87 (22.2) 1.30 (33) haft ends pline shaft 7/8 in 13T 16/32DP (AE J ()) ø7/8 in 1/4-20UNC (16) 0.99 ( (4 R pline shaft 7/8 in 13T 16/32DP (AE J ()) ø7/8 in 1/4-20UNC (16) 0.99 (25) 1.61 (4 Ports Plate 64, ports plate 61 see page 21 K Parallel keyed shaft Tightening torque, max. 2) Outlet port, threaded IO /16-12UNF-2; 0.79(20) deep 261 lb-ft (360 Nm) Inlet port, threaded IO /8-12UN-2; 0.79(20) deep 696 lb-ft (960 Nm) / 1 Case drain ports ( 1 plugged) IO /4-16UNF lb-ft (160 Nm) ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information DIA ,02) 0.10 (2.5) (ø /4-20UNC (28.6) 0.63 (16) 0.31 (8) 1.63 (41.3) ( ) ( ) 0.250

21 1.87 (47.6) 0.79 (ø20) 4.21 (107) RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 21/44 Unit dimensions, size 28 A10VO28 DFR1 (DFR, DRG)/52R()-VC62N00 efore fi nalizing your design please 0.47 (12) 0.37 (9.5) 0.25 (6.3) max (209.5) 5.49 (139.5) 3.54 (90) (ø101.6 h8 ) DIA (ø32) 2.31 (58.7) Y 4.86 (123.5) 2.87 (73) 2.60 (66) 2.70 (68.5) 0.55 (14.3) Flange AE J () 1.06 (27) (160) 1.19 (30.2) View Y port plate 62 right hand rotation 5.75 (146) 6.77 (172) 2.48 (63) Ansicht Z Z 0.87 (22.2) 2.60 (66) 2.60 (66) haft ends C Tapered 2) (IO ) DIA (19.024) DIA DIA (21.9 ( ) 5/8-18UNF-2A 0.75 (19) (3-0,2 ) 0.87 (22) A 0.16 (4) 0.57 (14.4) 2.19 (55.6) ( ) Taper 125:1000 ocation of service ports for left hand rotation; turn port plate 180 ection A ( ) ( ) Ports Plate 62 (6 (Dimensions of port plate 61 see page 20) Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1 Case drain ports ( 1 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information 2) only series 52

22 22/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 28 A10VO28 AD/53R()-VC61N00 efore fi nalizing your design please 5.49 (139.5) 3.54 (90) 9.09 ( (9.5) 0.25 (6.3) Flange AE J () DIA (ø101.6 h8 ) (29) 1 W 5.12 (130) 4.76 ( (74) (74) 0.12 (3) DIA 0.56 (ø14.3) 3.23 (82) 2.59 (75) 0.47 (12) 3.54 (90) 6.69 (170) 0.12 (3) (146) 6.77 (172) ViewY port plate 61 right hand rotation 2.48 (63) 2.31 (58.7) DIA 1.26 (ø32) DIA 0.79 (ø20) 1.87 (47.6) 4.49 (114) 1.19 (30.2) 0.87 (22.2) (33) (33) ocation of service ports for left hand rotation; turn port plate180 haft ends see page 20,21 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1 Case drain ports ( 1 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

23 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 23/44 Unit dimensions, size 28 A10VO28 AD/53R()-VC62N00 efore fi nalizing your design please 9.09 ( (139.5) 3.54 (90) DIA (ø101.6 h8 ) (9.5) 0.25 (6.3) Flange AE J () 1.14 (29) (ø32) 2.31 (58.7) Z 5.12 (130) 4.74 (120.5) 2.91 (74) 1 (3) 2.91 (74) DIA 0.56 (ø14.3) 3.23 (82) 2.95 (75) 0.47 (12) 3.54 (90) 6.30 (160) 7.36 (187) 1.19 (30.2) 0.12 (3) (146) 6.77 (172) View Y port plate 62 right hand rotation 2.48 (63) View Z 4.49 (114) 1.87 (47.6) DIA 0.79 (ø20) V 0.87 (22.2) 2.60 (66) 2.60 (66) ocation of service ports for left hand rotation; turn port plate 180 haft ends see page 20,21 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 3/4in 3/8-16UNC-2; 0.75 (19) deep 1 1/4in 7/16-14UNC-2; 0.79 (20) deep Tightening torque, max. 31 lb-ft (42 Nm) 48 lb-ft (66 Nm) / 1 Case drain ports ( 1 plugged) IO /4-16UNF lb-ft (160 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

24 1.50 (ø38) 0.98 (ø25) 24/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 45 A10VO45 DR/52R()-VC61(64)N00 efore fi nalizing your design please Flange AE J () (ø101.6 h8 ) DIA 0.37 (9.5) 0.25 (6.3) 3.90 (99) 0.47 (12) 1.18 (30) 1 Y 5.18 (131.5) 3.03 (77) 2.70 (68.5) 3.07 (78) 0.56 (14.3) 7.44 (189) max (220.5) 5.75 (146) 6.77 (172) View Y port plate 64 right hand rotation View Y port plate 61 right hand rotation 2.75 (69.9) haft ends pline shaft 1 in 15T 16/32DP (AE J (-)) 1.50 (38) 1.50 (38) ocation of service ports for left hand rotation; turn port plate 180 R pline shaft 1in 15T 16/32DP (AE J (-)) U pline shaft 7/8 in 13T 16/32DP (AE J ()) 1.41 (35.7) (26.2) 1.50 (38) (38) W pline shaft 7/8 in 13T 16/32DP (AE J ()) 2.06 (52.4) ø1in 1/4-20UNC-2 ø1in 1/4-20UNC-2 ø7/8in 1/4-20UNC-2 ø7/8in 1/4-20UNC (16) 1.18 (30) 1.81 (45.9) 0.63 (16) 1.16 (29.5) 1.81 (45.9) 0.63 (16) 0.98 (25) 1.61 ( (16) 0.98 (25) 1.61 (4 Ports 64 (ports plate 61 see page 25) Tightening torque, max. 2) Outlet port IO /16-12UN-2; 0.79 (20 ) deep 390 lb-ft (540 Nm) Inlet port IO /8-12UN-2; 0.79 (20) deep 696 lb-ft (960 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information

25 DIA RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 25/44 Unit dimensions, size 45 A10VO45 DFR1(DRG, DFR)/52R()-VC62N00 efore fi nalizing your design please 0.37 (9.5) 0.25 (6.3) max (220.5) 5.93 (150.5) 3.90 (99) 0.47 (12) 1.18 (30) (ø101.6 h8 ) DIA (ø38) 2.75 (69.9) Y 5.18 (131.5) (14.3) 3.03 (77) 2.70 (68.5) Flange AE J () 7.01 (178) 8.31 ( (35.7) View Y port plate 62 right hand rotation 5.75 (146) 6.77 (172) 2.68 (68) View Z 4.53 (115) 2.06 (52.4) 0.98 (ø25) Z haft ends ocation of service ports for left hand rotation; turn port plate (26.2) 3.54 (90) 3.54 (90) K haft C Tapered shaft (IO ) 2) 0.09 (2.2) (Ø ) 1/4-20UNC (34.9) 0.63 (16) 0.31 (7.9) 1.81 (46) Ports 62 (ports plate 61 see also page 24) Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 1in 3/8-16UNC-2; 0.71 (18) deep 1 1/2in 1/2-13UNC-2; 0.87 (22) deep Tightening torque, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information 2) only series (28.2-0,2) ( ) 0.84(21.4 DIA 1in (25.4) 0.99(25.16) 0.13 (3.2) 0.16 (4) 3/4-16UNF (28.6) A (3) (14.3) (19) (30) 2.12(53.9) 2.43 (61.8) ( ) Taper 125:1000 ection A ( ) ( )

26 1.50 DIA (ø38) 0.98 (ø25) 26/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions. size 45 A10VO45 AD/53R()-VC61N00 efore fi nalizing your design please 0.37 (9.5) Flange 0.25 (6.3) AE J () (Ø101.6 h8 ) DIA 0.47 (12) 9.25 (235) 5.75 (146) 3.90 (99) 1.22 ( (99) 7.44 (189) Y 5.24 (133) 4.84 (123) (75.5) 0.12 (3) View Y port plate 61 right hand rotation 5.75 (146) 6.77 (172) (3) 3.03 (77) 2.68 (68) 0.56 (14.3) 3.62 (92) 3.27 (83) 2.75 (69.9) 4.57 (116) haft ends see page 24, 25 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO (35.7) 30 1in 3/8-16UNC-2; 0.71 (18) deep 1 1/2in 1/2-13UNC-2; 0.87 (22) deep 1.03 (26.2) 1.50 (38) (38) 2.06 (52.4) Tightening torque, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information ocation of service ports for left hand rotation; turn port plate 180

27 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 27/44 Unit dimensions, size 45 A10VO45 AD/53R()-VC62N00 efore fi nalizing your design please 0.37 (9.5) 0.25 (6.3) Flange AE J () (Ø101.6 h8 ) DIA 0.47 (12) 9.25 (235) 5.75 (146) 3.90 (99) 1.22 ( (99) 7.00 (178) 8.31 ( (35.7) 1.50 (Ø38) 2.75 (69.9) Y 5.24 (133) 4.84 (123) (75.5) 0.12 (3) (146) 6.77 (172) 3.03 (77) 0.08 (2) (92) 3.27 (83) View Y port plate 62 right hand rotation 2.68 (68) View Z 4.57 (116) 2.06 (52.4) 0.98 (ø25) Z 1.03 (26.2) 3.54 (90) 3.54 (90) ocation of service ports for left hand rotation; turn port plate 180 haft ends see page 24, 25 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 1in 3/8-16UNC-2; 0.71 (18) deep 1 1/2in 1/2-13UNC-2; 0.87 (22) deep Tightening torque, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

28 28/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 63 A10VO63 DR/52R()-VC62N00 efore fi nalizing your design please Flange AE J () (ø101.6 h8 ) DIA 0.37 (9.5) 1.57 (40) 0.24 (6) 0.59 (15) max (220.5) 4.61 (117) (201.5) 9.43 (239.5) 1.69 (42.9) 1.97 (ø50) 3.06 (77.8) Y 5.39 (137) Mounting flange C 5.75 (146) 6.77 (172) (78.5) 0.56 (14.3) 3.42 (87) 2.99 (76) View Y port plate 62 right hand rotation View Z 2.06 (52.4) 0.98 (ø25) Z 1.11 (26.2) haft ends pline shaft 1 1/4 in 14T 12/24DP (AE J (C)) ocation of service ports for left hand rotation; turn port plate 180 R pline shaft 1 1/4 in 14T 12/24DP (AE J (C)) U pline shaft 1 in 15T 16/32DP (AE J (-)) 2.83 (72) 2.83 (72) W pline shaft 1 in 15T 16/32DP (AE J (-)) Ports ø1 1/4 in 5/16-18UNC (19) 1.56 (39.5) 2.18 (55.4) ø1 1/4 in 5/16-18UNC-2 Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code (19) 1.50 (38) 2.18 (55.4) AE J518c IO 68 AE J518c IO (16) 0.98 (25) 1.81 (45.9) 1in 3/8-16UNC-2; 0.71 (18) deep 2in 1/2-13UNC-2; 0.87 (22) deep Tightening torque, max. 2) 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) ø1 in 1/4-20UNC-2 ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information ø1 in 1/4-20UNC (16) 1.14 (29) 1.81 (45.9)

29 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 29/44 Unit dimensions, size 63 A10VO63 DFR1 (DFR, DRG)/52R()-VD61N00 efore fi nalizing your design please Flange AE J (C) (ø127 h8 ) DIA 0.5 (12.7) max (220.5) 5.93 (150.5) 4.61 (117) 1.57 (40) 0.24 (6) 0.59 (15) 1 1 Y 5.93 (137) 5.83 (148) Mounting flange D 0.56 (14.3) 3.09 (78.5) 4.51 (114.5) 2.99 (76) 3.43 (87) 8.19 (208) View Y port plate 61 right hand rotation 4.51 (114.5) 5.75 (146) 2.56 (65) 3.06 (77.8) 1.97 (ø50) 4.74 (120.5) 0.98 (ø25) haft ends 1.67 (42.9) 1.03 (26.2) 1.30 (33) 1.81 (46) ocation of service ports for left hand rotation; turn port plate (52.4) K Parallel keyed shaft C Tapered (IO ) 2) DIA ( ,03) 5/16-18UNC-2 Ports 0.12 (3) 1.63 (41.3) 0.75 (19) 0.31 (7.9) 2.18 (55.4) ( ,025 ) (35.3-0,2) Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 1in 3/8-16UNC-2; 0.71 (18) deep 2in 1/2-13UNC-2; 0.87 (22) deep Tightening torques, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information 2) only series (21.4 DIA (25.4) 0.99 (25.16) 0.13 (3.2) 0.16 (4) 3/4-16UNF (28.6) A (14. (3) 1.18 (30) (23.6) (34.9) 2.61 (66.4) DIA 1.25 (31.75) ( ) Taper 125:1000 ection A ( ) (

30 30/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 63 A10VO63 AD/53R()-VD61N00 efore fi nalizing your design please 9.72 (247) 5.93 (150.5) 4.55 (115.5) Mounting flange D 0.5 (12.7) (39) 1 1 Flange AE J (C) (ø127 h8 ) DIA Y 5.51 (140) 5.04 (128) 0.55 (14) 4.51 (114.5) 3.05 (77.5) (79) 5.75 (146) 3.46 (88) 3.50 (89) 0.59 (15) 4.55 (115.5) 8.19 (208) (114.5) 5.91 (150) View Y port plate 61 right hand rotation 2.56 (65) 3.06 (77.8) 1.97 (ø50) 0.98 (ø25) 2.06 (52.4) 4.88 (124) ocation of service ports for left hand rotation; turn port plate (42.9) 1.03 (26.2) 1.30 (33) 1.81 (46) haft ends see page 28/29 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 1in 3/8-16UNC-2; 0.71 (18) deep 2in 1/2-13UNC-2; 0.87 (22) deep Tightening torque, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

31 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 31/44 Unit dimensions, size 63 A10VO63 AD/53R()-VC62N00 efore fi nalizing your design please 9.72 (247) 5.91 (150) 4.55 (115.5) Mounting flange C (ø101.6 h8 ) DIA 0.37 (9.5) 0.25 (6.3) Flange AE J () 0.59 (15) 1.54 (39) (115.5) 7.93 (201.5) 9.43 (239.5) 1.69 (42.9) 1.97 (ø50) 3.06 (77.8) 5.51 (140) 5.04 (128) Y 3.05 (77.5) (146) 6.77 (172) (79) 0.56 (14.3) 3.50 (89) 3.46 (88) View Y port plate 62 right hand rotation 2.56 (65) View Z 4.88 (124) 2.06 (52.4) 0.98 (ø25) Z 1.03 (26.2) 2.83 (72) 2.83 (72) ocation of service ports for left hand rotation; turn port plate 180 haft ends see page 28/29 Ports Outlet port, AE fl ange (code 6 Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO 68 1in 3/8-16UNC-2; 0.71 (18) deep 2in 1/2-13UNC-2; 0.87 (22) deep Tightening torque, max. 31 lb-ft (42 Nm) 65 lb-ft (90 Nm) / 1 Case drain ports ( 1 plugged) IO /8-14UNF lb-ft (240 Nm) Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

32 32/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 85 A10VO85 DR/52R()-VD61N00 efore fi nalizing your design please max (242) 5.12 (130) 1.57 (40) 0.50 (12.7) Flange AE J (C) (ø127 h8 ) DIA (20) (245) Y 6.12 (155.5) View Y port plate 61 right hand rotation 6.22 (158) 7.13 ( (210) (95) 0.69 (17.5) 3.68 (93.5) 3.46 (88) 3.50 (88.9) 2.36 (ø60) 1.97 (50) 2.00 (50.8) ocation of service ports for left hand rotation; turn port plate (92) haft ends pline shaft 1 1/2 in 17T 12/24DP (AE J (C-C)) U pline shaft 1 1/4 in 14T 12/24DP (AE J (C)) W pline shaft 1 1/4 in 14T 12/24DP (AE J (C)) 1.77 (45) 1.25 (31.8) 311 (79) ø ø1 1/2 in 7/16-14UNC-2 ø1 1/4 in 5/16-18UNC-2 ø1 1/4 in 5/16-18UNC (28) 1.71 (43.5) 2.44 (61.9) 0.75 (19) 1.38 (35) 2.18 (55.4) 0.75 (19) 1.30 (33) 2.18 (55.4) Ports Outlet port, AE fl ange (code 62) Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO /4in 1/2-13UNC-2; 0.75 (19) deep 2 1/2in 1/2-13UNC-2; 1.07 (27) deep Tightening torque, max. 2) 65 lb-ft (90 Nm) 65 lb-ft (90) Nm / 1 Case drain ports ( 1 plugged) IO /16-12UN lb-ft (360 Nm) ANI 92.1a-1996, 30 pressure angle, fl at root, side fi t, tolerance class 5 2) see general information

33 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 33/44 Unit dimensions, size 85 A10VO85 DFR1(DFR, DRG)/52R()-VC62N00 efore fi nalizing your design please max (242) 6.75 (171.5) 5.12 (130) 1.57 (40) (ø127 h8 ) DIA (12.7) Flange AE J (C) 0.79 (20) (88.9) 2.36 DIA (ø60) Y 6.12 (155.5) (95) 0.69 (17.5) 3.46 (88) 3.68 (93.5) 9.27 (235.5) (276.8) 2.00 (50.8) View Y port plate 62 right hand rotation 6.22 (158) 7.13 ( (210) 2.91 (74) 0.45 (11.5) View Z 5.47 (139) 2.63 (66.7) 1.26 (ø32) Z 1.25 (31.8) 3.74 (95) 3.35 (85) ocation of service ports for left hand rotation; turn port plate 180 haft ends see page 32 Ports Outlet port, AE fl ange (code 62) Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO /4in 1/2-13UNC-2; 0.75 (19) deep 2 1/2in 1/2-13UNC-2; 1.07 (27) deep Tightening torque, max. 65 lb-ft (90 Nm) 65 lb-ft (90) Nm / 1 Case drain ports ( 1 plugged) IO /16-12UN lb-ft (360 Nm) Pilot pressure port IO /16-20UNF (11,5) deep 29 lb-ft (40) Nm see general information

34 34/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Unit dimensions, size 85 A10VO85 AD/53R()-VC61N00 efore fi nalizing your design please 0.50 (12.7) 0.40 (10.2) FlangeAE J (C) (ø127 h8 ) DIA 0.79 (20) (273) 7.15 (181.5) 5.63 (143) 1.42 (36) (130) 9.65 (245) Y 5.91 (150) 5.71 (145) 3.74 (95) 0.16 (4) ( (210) 3.74 (95) 0.16 (4) 3.98 ( (17.5) 4.04 (102.5) View Y port plate 61 right hand rotation 2.91 (74) 1.26 (ø32) 2.63 (66.7) 5.24 (133) 3.50 (88.9) 2.36 (ø60) ocation of service ports for left hand rotation; turn port plate (50.8) 1.25 (31.8) 1.97 (50) 1.77 (45) haft ends see page 32 Ports Outlet port, AE fl ange (code 62) Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO /4in 1/2-13UNC-2; 0.75 (19) deep 2 1/2in 1/2-13UNC-2; 1.07 (27) deep Tightening torque, max. 65 lb-ft (90 Nm) 65 lb-ft (90 Nm) / 1/2 Case drain ports ( 1/2 plugged) IO /16-12UN Nm Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

35 RA /11.07 A10VO Mobile Hydraulics osch Rexroth Corp. 35/ (273) 7.15 (181.5) 5.63 (143) 0.50 (12.7) 0.40 (10.2) Flange AE J (C) (ø127 h8 ) DIA Unit dimensions, size 85 A10VO85 AD/53R()-VC62N00 efore fi nalizing your design please 1.42 (36) (ø63) 3.50 (88.9) Y 5.91 (150) 5.71 (145) 3.74 (95) (95) 0.16 (4) 3.98 ( (17.5) 4.04 (102.5) 0.79 (20) 5.12 (130) 9.27 (235.5) (277) 2.00 (50.8) 0.16 (4) 2 View Y port plate 62 right hand roation 7.13 ( (210) 2.91 (74) 1.26 DIA (ø32) 2.63 (66.7) View Z 5.24 (133) Z 1.25 (31.8) 3.74 (95) 3.35 (85) ocation of service ports for left hand rotation; turn port plate 180 haft ends see page 32 Ports Outlet port, AE fl ange (code 62) Inlet port, AE fl ange (code 6 AE J518c IO 68 AE J518c IO /4in 1/2-13UNC-2; 0.75 (19) deep 2 1/2in 1/2-13UNC-2; 1.07 (27) deep Tightening torque, max. 65 lb-ft (90 Nm) 65 lb-ft (90 Nm) / 1/2 Case drain ports ( 1/2 plugged) IO /16-12UN Nm Pilot pressure port IO /16-20UNF-2; 0.45 (11.5) deep 29 lb-ft (40 Nm) see general information

36 36/44 osch Rexroth Corp. Mobile Hydraulics A10VO RA /11.07 Combination pumps A10VO + A10V()O Combination pumps offer the possibility to obtain mutually independent hydraulic circuits without the use of a splitter gearbox. When ordering combination pumps the model codes for the fi rst and the second pump must be joined by a "+". Ordering example: A10VO85DFR1/52R-VC12K04 + A10VO45DR/52R-VC11N00 If the second pump is not factory mounted, the simple type designation is suffi cient. In this case the delivery of the pump with through drive will include: a shaft coupler and a plastic cover to prevent dirt from entering the through drive opening. Permissible overhang moment It is permissible to use a combination of two single pumps of the same size (tandem pump) considering a mass acceleration force of max. 10 g (322 ft/sec 2 (9,81 m/s 2 )) without an additional support bracket. ize Permissible overhang moment static T m lb-ft (Nm) dynamic at 10 g (322 ft/sec 2 (9,81 m/s 2 )) T m lb-ft (Nm) Weight m 1 lbs (kg) Distance to center of gravity l 1 in (mm) 656 (890) 18 (8) 65 (89) 25 11,5 31 (14) 3.19 (8 664 (900) 66 (90) 40 (18) 3.74 (95) 1010 (1370) 101 (137) 48.5 (22) 3.94 (100) m 1, m 2 Weight of pumps [lbs (kg)] l 1, l 2 Dist. to center of gravity [in (mm)] 2270 (3080) 227 (308) 75 (34) 4.8 (122) l 1 l 2 m 1 m 2 (T m = (m 1 l 1 + m 2 l 2 ) 1 12 (102) [lb-ft (Nm)]) Overview of through drive mounting options Through drive - A10VO/5x Mounting option second 2. pump Through drive Flange AE J744 Coupler for splined shaft Code A10V()O../5x... ize (shaft) A10VO../31... ize (shaft) Gear pump eries (ize) available on size 82-2 (A) 5/8 in K01 10 (U) 18 (U) F (5...22) /4 in K52 10 () 18 (, R) () 7/8 in K68 28 (, R) 45 (U, W) 28 (, R) 45 (U, W) N/G ( ) in K04 45 (, R) 45 (, R) 63 (U, W) 2) (C) 1 1/4 in K15 63 (, R) (C) 1 1/4 in K07 85 (U, W) 71 (, R) /2 in K24 85 () 85 not on size 28 and 45 with K68 2) not on size 45 with K