END SEAL CAPS. SUPER SEAL CORPORATION 45 Seymour Street P.O. Box 394 Stratford, CT 06615

Transcription

1

2 END SEL CPS SUPER SEL CPS Super Seal End Seal Caps provide wire and cable with superior environmental protection against damage and moisture. The patented material formulation provides high quality sealing protection for most cable jacket material including XLPE, PVC, PILC and Rubber. Super Seal Caps are utilized across many industries including wire and cable manufacturers, utilities, industrial users and M s. They are available in a full range of sizes from 1/4" through 19½" diameters; available with and without valves for external pressurization. TECHNICL SPECIFICTIONS PROPERTIES VLUE STNDRD PHYSICL Tensile Strength 12 MPa (1740 psi) STM D638 Ultimate Elongation (Min) 350% STM D638 Density gm/cm 3 STM D792 Hardness Shore D STM D2240 Water bsorption (Max) 0.2% STM D570 Specific Gravity (Max) 1.05 STM D792 THERML ccelerated ging (500 Hours) 120 C (248 F) STM D2671 Tensile Strength (Min) 11 MPa (1595 psi) STM D638 Ultimate Elongation (Min) 300% STM D638 Heat istortion 150 C (302 F) 2% STM D1047 Low Temperature Flexibility -40 C (-40 F) for 4 Hrs. No Cracking STM D2671 Heat ock 250 C (482 F) for 30 Min. No Cracking or Flowing ESI Shrink Temperature 125 C (257 F) IEC 216 Continuous Temperature Limit -40 to100 C (-40 to 212 F) IEC 216 ELECTRICL Dielectric Strength (Min) 12 KV/mm (304.8 KV/in) STM D149 Volume Resistivity (Min) 1 x Ohm.cm STM D257 Dielectric 60 Hz (Max) 5 pf STM D150 issipation Factor 0 H (Max) STM D150 CHEMICL Ozone Resistance 48 hrs@ 0.03 No Cracking SUPER SEL CORPORTION 45 Seymour Street P.O. Box 394 Stratford, CT 06615

3 DIMENSIONL DT Side View C Closed End View Open End View B SUPER SEL END CP SIZE SELECTION Super Seal Nominal Inside Diameter "" Length "B" Wall Thickness "C" Cable Diameter Range Diameter Supplied Diameter Recovered Diameter Overall Cap Length Recovered (+/- 20%) Part # (inches) (mm) (inches) (mm) (inches) (mm) (inches) (mm) (inches) (mm) (inches) G- 1/4" G-B 3/8" G-B L 3/8" G-B 1/2" G-B L 1/2" G-1 3/4" G-1 L 3/4" G-1 7/8" G-1 L 7/8" G-2 1" G " G-3 1.5" G-3 L 1.5" G " G-3 L 1.25" G-8 2" G-8 L 2" G-8 2" G-8 L 2.25" G-4 2.5" G-4 L 2.5" G " G-4 L 3.25" G-7 3.5" G-7 L 3.5" G " G-7 L 4.75" G-6 5" G-6 L 5" G-12 6" G-12 L 6" G-801 9" G " G ' G " Shaded Indicates Stock Item PPLICTION METHOD The wire/cable end shall be thoroughly cleaned prior to placing properly sized cap over cable end. Evenly apply heat from heat gun or propane torch. Begin to shrink the closed end of the cap first and continue to apply heat to the cap by moving towards the open end. pply heat until the entire cap is firmly fitted to the cable. Sealant will flow from the open end. llow cap to cool. Before During fter Prepare cable and select the appropriate size cap Place cap over cable end and apply heat End cap shrinks creating a durable and protective seal Tel: (203) Fax: (203)

4 LOW VOLTGE TUBING SUPER SEL TUBING Super Seal Low Voltage adhesive lined tubing is available in both medium and heavy wall sizes. Medium wall tubes (series GMW) are used for environmental protection of low voltage cable terminations and insulating connectors for low voltage straight through joints, splices and jacket repairs up to 1.1KV. Heavy wall tubes (series GHW) are used for mechanical protection and outer sealing of underground straight through cable joints, splices and jacket repairs up to 36KV. They both have excellent resistance to weathering, UV rays, chemicals and solvents and conform to the IEC standard and are available in multiple lengths and diameters from 1/2 up to 7.8 TECHNICL SPECIFICTIONS PROPERTIES VLUE STNDRD MECHNICL Tensile Strength Test 13 MPa ( psi) STM D638 Ultimate Elongation (Min) 350% STM D638 Density gm/cm 3 STM D792 Hardness Shore D STM D2240 Water bsorption (Max) 0.18% STM D570 Specific Gravity (Max) 1.05 STM D792 THERML ccelerated ging (500 Hours) 120 C (248 F) STM D2671 Tensile Strength (Min) 11 MPa (1595 psi) STM D638 Ultimate Elongation (Min) 300% STM D638 Heat 150 C (302 F) 2% STM D1047 Low Temperature Flexibility -40 C (-40 F) for 4 Hrs. No Cracking STM D2671 Heat Shock 250 C (482 F) for 30 Min. No Cracking or Flowing ESI Shrink Temperature 125 C (257 F) IEC 216 Continuous Temperature Limit -40 to100 C (-40 to 212 F) IEC 216 ELECTRICL Dielectric Strength (Min) 18 KV/mm (457.2 KV/in) STM D149 Volume Resistivity (Min) 5 x Ohm.cm STM D257 Dielectric 60 Hz (Max) 4.0 pf STM D150 CHEMICL Ozone Resistance No Cracking SOLVENT RESISTNCE TEST Tensile Strength Test 11.5 MPa (1668 psi) STM D257 Elongation Test Di-Electric Test (Min) 325% 15 KV/mm (381 KV/in) STM D257 STM D257 CORROSION TEST Tensile Strength Test 11.5 MPa (1668 psi) ESI Elongation Test 325% ESI SUPER SEL CORPORTION 45 Seymour Street P.O. Box 394 Stratford, CT 06615

5 DIMENSIONL DT Side View Front View Isometric View B MEDIUM WLL TUBING SELECTION CHRT Inside Diameter "" Wall Thickness "B" Cable Range Super Seal Part # Supplied Recovered Recovered (+/- 20%) Size Diameter (mm) (inches) (mm) (inches) (mm) (inches) WG KCML (mm) (inches) GMW 10/ #14 - # GMW 12/ #12 - # GMW 19/ #8 - # GMW 27/ #2-2/ GMW 40/ / GMW 51/ GMW 70/ GMW 90/ GMW 115/ GMW 130/ GMW 140/ GMW 160/ GMW 180/ GMW 200/ HEVY WLL TUBING SELECTION CHRT Inside Diameter "" Wall Thickness "B" Cable Range Super Seal Part # Supplied Recovered Recovered (+/- 20%) Size Diameter (mm) (inches) (mm) (inches) (mm) (inches) WG KCML (mm) (inches) GHW 13/ #12 - # GHW 20/ #8 - # GHW 33/ #4-4/ GHW 40/ / GHW 51/ GHW 70/ GHW 85/ GHW 105/ GHW 120/ GHW 140/ GHW 160/ GHW 180/ GHW 200/ Tel: (203) Fax: (203)

6 WRP SLEEVES WRP SLEEVES Super Seal Low Voltage adhesive lined tubing is available in both medium and heavy wall sizes. Medium wall tubes (series GMW) are used for environmental protection of low voltage cable terminations and insulating connectors for low voltage straight through joints, splices and jacket repairs up to 1.1KV. Heavy wall tubes (series GHW) are used for mechanical protection and outer sealing of underground straight through cable joints, splices and jacket repairs up to 36KV. They both have excellent resistance to weathering, UV rays, chemicals and solvents and conform to the IEC standard and are available in multiple lengths and diameters from 1/2 up to 7.8 TECHNICL SPECIFICTIONS PROPERTIES VLUE STNDRD MECHNICL Tensile Strength (Min) 17 Mpa (2465 psi) STM D638 Ultimate Elongation (Min) 300% STM D638 Water bsorption (Max) 0.20% STM D570 C 48 rs. for 50 C 122 F No Crack STM D570 Torchability No Split TE 201 OL THERML ccelerated geing (500 Hrs) 120 C (248 F) STM D2671 Tensile Strength (Min) 15 Mpa (2175 psi) STM D638 Ultimate Elongation (Min) 220% STM D638 Heat Shock 250 C (482 F) for 30 Min. No Cracking or Flowing ESI Shrink Temperature 125 C (257 F) IEC 216 Continuous Temperature Limit -40 C to 100 C (-40 F to 212 F) IEC 216 ELECTRICL Dielectric Strength (Min) 12 KV/mm. (304.8 KV/in) STM D149 CHEMICL Chemical SOLVENT resistance RESISTNCE in 0.1 N TEST sol.of Na2,So4,Na2,Nacl2,H2so4 No Cracking STM D2671 Tensile Strength Test 15 MPa (2175 psi) STM D638 Elongation Test 200% STM D638 SUPER SEL CORPORTION 45 Seymour Street P.O. Box 394 Stratford, CT 06615

7 DIMENSIONL DT Flat View Front View B Side View F ETURES e wrap slee es are ma e from same t ermally stabili e cross linke polymeric material as cable our en caps an low oltage tubing. Hig rink ratio co ers irregular s apes. Hot melt a esi e pro i es complete en ironmental sealing an insulation. uickly reco ers for cost efficient repairs WRP ROUND SLEEVE SELECTION CHRT Inside Diameter "" Wall Thickness "B" Cable Range Super Seal Part # Supplied Recovered Recovered (+/- 20%) Size Diameter (mm) (inches) (mm) (inches) (mm) (inches) WG KCML (mm) (inches) GWS 55/ GWS 76/ GWS 105/ GWS 140/ GWS 190/ GWS 200/ PPLICTION METHOD The wire/cable shall be thoroughly cleaned prior to placing properly sized wrap sleeve over cable. Evenly apply heat from heat gun or propane torch. Begin to shrink one end of the wrap sleeve first and continue to apply heat to the sleeve by moving towards the opposite open end. pply heat until the entire sleeve is firmly fitted to the cable. Sealant will flow from the open ends. llow sleeve to cool. Before During fter Prepare cable and select the appropriate size sleeve Place wrap sleeve over cable end and apply heat Wrap sleeve shrinks creating a durable and protective seal Tel: (203) Fax: (203)

8