ONYX 360. Rolling PDC cutter

Transcription

1 ONYX 360 Rolling PDC cutter

2 ONYX 360 Rolling PDC Cutter Applications Drilling conditions that cause and accelerate PDC cutter wear Abrasive environments Benefits Extends bit durability Increases run footage and average ROP Improves thermal dissipation to extend cutter life Features 360 revolution capability allows cutter to stay sharper longer Number and placement of cutters can be customized to maximize durability in bit cutting structure s high-wear areas Can be integrated into any PDC bit cutting structure without changing cutter size Available in 13-mm and 16-mm sizes

3 The next revolution in PDC cutter durability The ONYX 360* rolling PDC cutter substantially increases PDC bit durability by revolving 360. Strategically positioned in the highest wear areas of a bit s cutting structure, the rolling cutter s entire diamond edge is used to shear the formation. The cutter s rotating action allows the diamond edge to stay sharper longer, extending ONYX 360 cutter life far beyond that of premium fixed cutters. When compared with bits that only have fixed cutters, PDC bits that included ONYX 360 rolling cutters demonstrated run length increases of up to 57%.

4 Microscopic inspection of PDC cutters enabled analysis of diamond edge wear after running cutters on test formations.

5 Revolving edge advances PDC cutter durability Challenge Development Simulation Evaluation Results Improve PDC cutter durability: Extend cutter life in high-wear applications Employ the cutter s entire diamond edge to minimize wear Sustain a bit s initial high ROP Explore new cutter designs: Determine feasibility of a more robust cutter system Investigate the functionality of dynamic cutters Analyze cutting forces that generate rotation Undertake cutter analysis using IDEAS* integrated drillbit design platform: Identify which fixed cutters to replace Optimize orientation and placement of rolling cutters in PDC bit blade Conduct extensive testing: Measure durability increases of rolling cutter Assess strength of dynamic PDC cutter system Confirm 360 rotation of cutter Quantified ONYX 360 rolling cutter s effectiveness and durability: Increased cutter durability Increased ROP up to 44% Extended run lengths up to 57%

6 Cutter s diamond edge goes largely unused The introduction of PDC cutters in the 1970s permanently changed well construction programs. Now, they are readily accepted as the workhorse cutting element of the drilling industry, accounting for over 80% of the total footage drilled in oil and gas wells worldwide. Despite their dominance, fixed PDC cutters have an inherent limitation: Most of the cutter s edge is fixed into the bit blade, limiting contact with the formation. Accordingly, more than 60% of the cutter s circumferential edge goes unused during a bit run. Cutter used 10 to 40% Cutter unused 60 to 90% Unused cutter Cutting edge More than 60% of a fixed PDC cutter s diamond edge goes unused (green) during a bit run, leaving only 10 to 40% of the edge (red) to cut the formation. Challenge

7 Fixed cutter design limits cutter potential The part of a fixed cutter s edge that engages the formation is subjected to mechanical and thermal effects that cause wear and chipping. This concentrated degradation on a small percentage of the cutter s edge results in loss of shearing efficiency, slowing the rate of penetration. In addition, bit durability is substantially reduced, resulting in shorter bit runs. NT e e e e e e e e e e e e e+02 Fixed PDC Cutter Using a rolling PDC cutter would increase durability by ensuring that the part of the cutter s edge making contact with the formation is continually refreshed to stay sharper longer. In addition, the rotating action would improve thermal dissipation preventing concentrated heat buildup. A dull photo (left) illustrates the degree of wear a fixed cutter incurs and where it is most concentrated. Finite element analysis (FEA) modeling software depicts the amount of frictional heat generated by a fixed cutter (right), with concentrated heat buildup in red. In an analysis of over 45,000 PDC bit runs, 60% of dull grade characteristics were identified as worn and chipped cutters, conditions that shorten cutter life and result in lower ROP and premature bit trips. Challenge

8 Inventive design increases cutter life Integrating a rolling cutter into a PDC bit s cutting structure required a novel and robust design. Smith Bits R&D engineers developed a cutter system composed of a housing that is brazed into the bit blade, and within which a sleeve encloses and completely secures the cutter while allowing it to rotate. The ONYX 360 cutter s shaft is fully contained within an integrated housing to ensure continuous rotation and cutter retention during drilling. The rolling cutter s orientation in the bit blade, relative to its contact with the formation and the bit s drilling force, drives efficient rotation of the cutter.

9 Durability analysis includes mounting PDC cutters in a test fixture and running them on formation samples. Development

10 Cutter durability advances to a new level To compare the new rolling cutter with a premium PDC fixed cutter, durability tests were conducted in which both cutters were mounted on test fixtures to engage a granite test formation with an unconfined compressive strength of 30,000 psi. To maintain a constant ROP, the vertical force required for premium fixed cutters had to be continually increased from 100 lbf to over 1,200 lbf to compensate for their wear rate. ONYX 360 rolling cutters required substantially less force, confirming that the cutter was remaining sharp for the complete test interval. Average vertical force, lbf 1,400 1,200 1, ONYX 360 cutters Premium fixed cutters Number of cutting passes When compared with premium fixed cutters, ONYX 360 cutters required far less additional loading force as drilling progressed, indicating improved cutting durability. Development

11 Comprehensive evaluation validates rolling concept Premium fixed cutter 90 The wear that fixed cutters incur is concentrated on a small percentage of the cutter s entire diamond edge. As a result, after 90 passes on a test formation, premium fixed cutters developed extreme wear flats. Because 100% of the ONYX 360 rolling cutter s diamond edge engaged the test formation, wear was evenly distributed and resulted in virtually no wear after 300 passes and very little wear after 540 passes. ONYX 360 cutter Rock cutting passes Development

12 IDEAS platform determines cutter integration Upon completion of laboratory testing, bit design engineers entered the ONYX 360 cutter s design in the IDEAS platform. This step enabled engineers to integrate cutters into the PDC bit s cutting structure. Integration was determined by examining the effect different geometric orientations had on three cutter characteristics: durability, appropriate balance of driving force, and aggressiveness. The IDEAS drillbit design platform enabled engineers to optimize placement of the rolling cutters on bit blades to ensure reliable cutter rotation. Simulation

13 Drilling force analysis optimizes cutter placement By analyzing the highest wear areas of cutting structures on PDC bits with only fixed cutters, design engineers were able to identify where ONYX 360 cutters should be positioned on bit blades to optimize cutter life and bit durability. Wear Flat Area, in 2 Wear Flat Area After 150 hours High wear area Distance from bit center, in In abrasive formations, the bit s shoulder area (between the center of the cutting structure and gauge) typically experiences the greatest amount of cutter wear. The ability IDEAS drillbit design platform has to predict the degree and precise location of this wear makes it an essential design tool. ONYX 360 cutters Premium fixed cutters Using IDEAS design platform enables fixed cutters, in the highest wear areas of a PDC bit s cutting structure, to be selectively replaced with ONYX 360 rolling cutters Distance from bit center, in Simulation

14 Rotating action greatly extends cutter life For the most direct comparison, ONYX 360 rolling cutters were fitted to a PDC bit blade next to premium fixed cutters. After drilling an 1,800-ft horizontal section in abrasive sandstone, both cutter types were compared: The dull condition of neighboring fixed cutters graded poor, while the rolling cutters were in excellent condition. This resulting low and uniform wear provided evidence that rotation had taken place, and using ONYX 360 rolling cutters in the shoulder area would increase drillbit durability. aa b B cc dd ONYX 360 cutters (A-D) showed virtually no sign of wear (dull grade T0) compared with the adjacent fixed cutters (dull grade T1 and T2). Evaluation

15 B C A D Dull bit with ONYX 360 cutters after drilling 1,800 ft through abrasive sandstone in 160 hours. Evaluation

16 Case Study Chesapeake Energy Improves Footage per Bit and ROP in Abrasive Formation with ONYX 360 Rolling PDC Cutters The operator deployed bits with 16-mm rolling cutters to increase bit run length and ROP compared with 13-mm rolling-cutter and fixed-cutter bits, Oklahoma Challenge Improve footage and ROP per bit while drilling horizontal laterals in Oklahoma s abrasive Colony Wash play. Solution Deploy bits fitted with 16-mm ONYX 360 rolling PDC cutters to maintain an efficient cutting structure for improved run length and ROP. Results Increased footage and ROP across three wells in the same play. Drilled the highest ROP for a Colony Wash lateral using 16-mm rolling PDC cutter bits. Results

17 Average Footage, ft Fixed cutters 13-mm ONYX 360 cutters 16-mm ONYX 360 cutters 2,500 Average ROP, ft/hr 25 2,000 1, Since 2009, Chesapeake has deployed various fixed and rolling cutter types in the Colony Wash play. Upon introducing 16-mm ONYX 360 cutters in 2015, the operator increased both footage and ROP (data averaged across 6 runs using the new cutters). 1, Results

18 Case Study Chesapeake Energy Increases Run Footage and Reduces NPT in Intermediate Section, Onshore Louisiana The operator gained an additional 1,500 ft of bit life in the highly abrasive Hosston Sands and Cotton Valley Lime with 16-mm ONYX 360 rolling PDC cutters I think we have some significant opportunity to make this intermediate hole section a consistent two-bit section. Depending on what we can do with ROP, this may develop into a one-bit hole section like we aspire to in most of our other plays. Greg Bruton Drilling Advisor Chesapeake Energy Challenge Increase run footage by 1,500 ft to at least 9,500-ft MD with one bit to enable running a more aggressive bit to complete the lower intermediate section for improved overall ROP. Solution Use the IDEAS platform to determine the optimal bit design for the application; deploy 16-mm ONYX 360 rolling PDC cutters for improved wear and extended cutter life. Results Increased run footage to reduce an unnecessary bit trip in the intermediate section with increased overall ROP and less rig NPT associated with drillout (DO) runs. Results

19 Offset Pad Well 1 Fixed Cutter DO Run Offset Pad Well 2 Fixed Cutter DO Run Offset Pad Well 3 Fixed Cutter DO Run ONYX 360 Cutters Well A DO run ONYX 360 Cutters Well B DO run ONYX 360 Cutters Well C DO run An 83/4-in bit fitted with ONYX 360 cutters outperformed conventional PDC bits with similar drilling parameters in the same formation. 5,864 ft 85.0 ft/h 69.0 h 6,095 ft 60.0 ft/h h 4,496 ft 71.5 ft/h 62.5 h 8,075 ft 48.5 ft/h h 47.4 ft/h 48.6 ft/h 7,892 ft , h ft h Drilling Parameters ONYX 360 Cutter DO Section Lower Intermediate Section Depth in, ft 1,850 9,500 Depth out, ft 9,800 10,000 11,000+ Section length, ft 7,800 8,000 1,800 Drilling time, h (on bottom) Dull grade 2-3-BT-S-XXX- IN-WT-BHA 2-2-WT-S-XXX- IN-WT-TD Water-base mud, lbm/galus ROP, ft/h Results

20 Case Study ONYX 360 Cutter Increases PDC Bit s Run Footage 57% in Granite Wash Formation, Texas Bit with rolling cutters drills 1,562 ft of a 5,113-ft, 61 8-in lateral gas well section at 25 ft/h Challenge Drill 61 8-in lateral gas well sections of at least 5,000 ft through abrasive reservoir sand, which caused some fixed-cutter-only PDC bits to be replaced after drilling less than 65 ft. Solution Run a 61 8-in MSiR613 PDC bit fitted with seven ONYX 360 rolling PDC cutters positioned in the areas of the bit s cutting structure with the highest predicted wear. Results Drilled 1,562 ft of a 5,113-ft, 61 8-in lateral gas well section at 25 ft/h using a bit with rolling cutters, which when compared with the best drilling performances in the same formation by fixedcutter-only bits, increased ROP 44% and footage drilled 57%. Results

21 10,000 MSiR613 MSi613 MSi713 MSi613 Other bit MSi611 Other bit Other bit 30 Depth, ft 11,000 12,000 13,000 14,000 15, , ROP, ft/h The in MSiR613 PDC bit drilled a 1,562 ft lateral in the hard and abrasive Granite Wash formation. When compared with the best performance by a bit with only fixed cutters drilling the same lateral well, the PDC bit with ONYX 360 rolling cutters reported an average ROP increase of 44% and a run length increase of 57%. 16, Depth in ONYX 360 bit Smith Bits PDC bits Other bits ROP Results

22 ONYX 360 Rolling PDC cutter Find out more about ONYX 360 rolling PDC cutter technology at slb.com/onyx360 *Mark of Schlumberger Other company, product, and service names are the properties of their respective owners. Copyright 2015 Schlumberger. All rights reserved. 15-BT-27703