1.) CENTAUR 50 GAS TURBINE GENERATOR PACKAGE

Transcription

1 M&M Export Limited Kanta House, Victoria road, South Ruislip, Middlesex HA4 0JQ, United Kingdom TEL: , FAX: Subject to prior sale 1.) CENTAUR 50 GAS TURBINE GENERATOR PACKAGE ORIGINAL DATE OF MANUFACTURER ,867 FIRED HOURS FROM NEW 1. GAS TURBINE - Centaur 50 (T5701) Gas Turbine. Nominal 4.0 MW. - Speed reducing gearbox. - Flexible shear coupling. - Vibration monitoring system (two channel - turbine and gearbox). GAS TURBINE AUXILIARY SYSTEMS 2. GAS FUEL SYSTEM - Pressure monitor. - Primary and secondary shut off valves. - Fuel control valve. - Fuel control actuator. - Polishing filter unit. 3. LUBRICATION SYSTEM - Main pump mechanically driven from gas turbine gearbox. - AC motor driven pre/post pump. - Duplex oil filter. - Oil tank in skid base. - Pressure and temperature controllers. - Oil coalescer (supplied loose). 4. ELECTRO-HYDRAULIC START SYSTEM - Hydraulic start motor (gearbox mounted). - Hydraulic pump (AC motor driven). - Oil tank. 5. COLD CRANK WATER WASH SYSTEM - Cold crank water wash manifold - Water wash trolley supplied loose incorporating: 6. AC GENERATOR (LEROY SOMER) - Horizontal, 2 sleeve bearing, 4 pole. - Salient pole brushless. - Open air circuit. - Enclosure IP21. - Temperature rise F. - Insulation Class F. - Supply 3.3KV/3-phase/3 wire/50 Hz. - Continuous rating matched to gas turbine (total temperature basis) at 0.8pf across specified ambient range.

2 - Automatic voltage regulator including parallel operation CT's quad droop assembly, three phase sensing, power factor control and manual operation. (AVR etc. mounted in control panel). - CT's 3 off for protection. - CT's 3 off for Dale instrumentation - VT between star point and earth for protection relays. - Stator winding temperature monitoring (2 RTD's per phase). - Drive end and non-drive end bearing temperature detection. - Drive end and non-drive end bearing seismic vibration monitors. - Anti condensation heaters. OFF SKID CONTROL AND ELECTRICAL EQUIPMENT 7. TURBINE CONTROL PANEL - Gas turbine/auxiliary systems/governor/load/t5 sequence controller (Mitsubishi PLC). - Visual display unit system interface. - Turbine and alternator vibration monitoring equipment. - T5 temperature indicator. - Turbine speed indicator. - Turbine hours run indicator. - Turbine start counter. - Hard wire PLC backup logic where required. - Miscellaneous push buttons, switches and indicators as required by Dale Control System. - Miniature molded case circuit breakers for circuit protection. - Panel anti condensation heater and thermostat. - Additional panel mounted hardware including PLC computer serial interface module to enable remote monitoring and external systems interface. - PC power supply socket. 8. ALTERNATOR CONTROL PANEL - Key pad operated electronic metering unit (V, Hz, A, kw, kwh, kvar and PF). - Bus/Mains and generator zero voltmeter. - Bus/Mains and generator dual scale frequency meter. - Synchroscope. - Automatic synchronizing equipment including check sync relay. - Miscellaneous push buttons, switches and indicators. - Miniature molded case circuit breakers for circuit protection. - Panel anti-condensation heater and thermostat. - Loose items supplied with the alternator, for example the AVR, are also mounted in the control panel. 9. AUXILIARY SYSTEMS PANEL - DC backup battery and charger. - DC voltmeter and under voltage detection. - Panel anti-condensation heater and thermostat. 10. DOCUMENTATION 2 copies of the following supplied: - Dale instruction manual. - Full set of operation and maintenance manuals. - Manufacturing programme.

3 Drawings: - General arrangement. - Foundation loading. - Electrical schematics - Liquid schematics. - Fuel schematics. 11. MISCELLANEOUS - First fill of lubricating and hydraulic oil. - Static test at Dale works. - First years supply of consumables - Outdoor Enclosure. - GT combustion air intake filters, ductwork and attenuation. - Enclosure ventilation fan. - Fire and gas detection/fire fighting equipment. - Enclosure ventilation inlet and outlet filters, ductwork and attenuation - Power Transformer. 13. SALES OPTIONS - 5 Year extended warranty and maintenance contract. - Installation & Commissioning. - Euros 125, except Iraq Customer to provide engineer(s) with good quality single accommodation, food and transport upon arrival at works, at no cost to Contractor. - Dual Fuel Conversion Hz Conversions. - Refurbished to Zero Hours. - Euros 3,250, FOB Europe Port Warranty will be 12 month from Installation or 5000 running hours, whichever is soonest. - Upgraded Controls System. - As is where is. United Kingdom - Delivered. SALES PRICE FOB Europe 962, All transport and shipping costs at buyers charge Remarks: 1.) Installation and putting into operation on request. 2.) the plant is in excellent condition and finally inspected by AXA in April ) 1 NEW ST18 POWER GENERATION PACKAGE The ST18 power generation package is a fully integrated modular system, which can be installed offshore to generate ultra-low-cost ancillary power directly from excess gas production. The self-contained package can generate approximately 2MW of electrical power at 600V, making a significant contribution towards a reduction in installation operating costs (eg. by cutting diesel consumption) while at the same time improving overall environmental performance by reducing flaring. PRICE: 3.38 Mill. EX Work. Delivery: Ex-Stock Guaranty: with full warrantee. 3.) 10.5 MW CATERPILLAR Diesel Power Plant, HFO, 1994 << General Information >> (3) x 3500 kw Caterpillar 3616 Diesel Generator Sets, 6.6 kv, 50 Hz (2) ran continuous at 85 % loading and (1) kept as standby until Plant is in perfect working order and now runs only in grid power outages. D.G. Sets are designed for operation on Heavy Fuel Oil (Bunker "C"). Average gross kwh/liter of Bunker C as fuel achieved was 4.05 during continuous operation.

4 Power Plant is equipped with: Associated Auxiliaries Electrical Control Power Switchgear with adequate standby units for reliable operation. Plant does not have Waste Heat Recovery System although possible to install. All scheduled Maintenance, minor & major, were carried out under the supervision of authorized manufacturer representatives. Set 1 (11881 hrs), Set 2 (18724 hrs), Set 3 (24909 hrs) Tools & Tackles required for Maintenance are available Manual for Operation & Maintenance, Specifications of all Equipments available All Maintenance was done under Supervision of Dealer as per recommended schedule Price for this Plant is 6,100, ) Hazardous Waste Incineration Plant - Chemical-Physical Treatment Plant - Evaporation Plant The incineration plant Annual throughput - 30,000 tons/annum daily output - approx. 120 tons Hourly average - 5 tons/hr Heat load - 58 GJ/hr (max.) Tank farm with 20 tanks of total volume approx. 1,500 m for liquid waste materials 3 storage depots for approx. 200 tons of waste in drums or other containments 4 bunkers for solid/pasty materials with a total volume of 580 m Incineration plant with rotary kiln technology and post combustion chamber Rotary kiln - diameter 4 meters, length 12 meters Post combustion chamber - diameter 5.6 meters, height 22 meters Boiler for steam generation 2 MW turbine for power generation Slag/ash loading with separation of metallic scrap by a magnetic separator 4-step flue gas purifying plant, consisting of an electric dust precipitation unit, wet scrubbers, catalytic nitrogen oxide removal plant and a dry adsorption step with fluidized bed reactor and fabric filter baghouse. Products and residual materials Process steam - 17 tons/hr (28 bar, 320C) Electric power: 2 MW for internal use and supply to the public network. Approx. 6 MW long-distance energy for internal use and supply to the public network. Electrical peak load MVA Installed driving power MW Average own requirements MW Approx tons/annum slag/ash for recycling and use in landfill construction Approx. 1,000 tons/annum filter dust Approx. 5,000 tons/annum waste gas washing water Approx. 250 tons/annum coarse and fine metallic scrap for recycling in the scrap metal trade Approx. 35,000 m/hr purified waste gases

5 Price: Euro 17,5 Mill. EXW Europe Scope and pictures available 5.) 250 MW Oil fired power station. The plant is unused and in excellent condition 250 MW station comprising a single steam generator/steam turbine-alternator unit, designed to burn heavy fuel oil. YOM 1975 and completed in 1979 The sudden unexpected and rapid rise in the price of oil in the 1970's, and a less than forecast demand for power, a decision was made to place the station in long term storage. Maker: Mitsubishi Heavy Industries Ltd, Japan Serial Number: T-602 Type: Three casing, tandem compound, double flow, condensing, single reheat. Speed : 3,000 rpm Nominal Rating : 250,000 kw Steam Conditions at Turbine Stop Valves - Pressure : 124 barg Temperature : 538C Steam Flow (max) : 748,660 kg/h (786,093 kg/h design) Number of Extractions : Six (6) Number of Stages : Fifty-five (55) Overall Length of Unit : 34 metres Overall Width of Unit : 8.5 metres Height of unit above Floor line : 5.0 metres Design steam conditions are 124 bar gauge and 538C at the turbine stop valves. Reheat temperature is 538C and the design exhaust pressure is 74 mbar absolute. The nominal rating of the unit is 250,000 kw at a guaranteed steam flow rate of 748,660 kg/h through the stop valves at 124 bar gauge main steam pressure and 76 mbar absolute back pressure. We understand it cost US $333 million to construct Price: US$ 67.5 Mill. Ex-Works A full set of instruction and operation manuals are included Scope available An Indian Company that specializes in the dismantling and re-assembly of this type of equipment has already visited the site and is familiar with the requirements to relocate it.