1x - Power Cord^ - (May vary slightly by color and/or length) 1x - Hook-up Wire w/ Fork Ends* 1. General Specifications...2

Transcription

1 Thank you for purchasing a TS series traffic light control. By design, all TS Series controls are built for ease of use and years of trouble free operation and enjoyment. While manufactured in the USA, all controls are inspected and tested prior to shipment for reliability. Please refer to the following information on your TS series control. What s included: (Control Only) 1x - TS Series Control 4x - Adhesive Mounting Posts Components included as a Kit : (Optional - TS10 & TS12) 1x - Power Cord^ - (May vary slightly by color and/or length) 1x - Hook-up Wire w/ Fork Ends* * TS12 Series Include 2x - Hook-up Wire w/ Fork Ends. ^ Power Cord Included with TS14 Series. TABLE OF CONTENTS Page 1. General Specifications Installation & Safety Tips TS10 Control Switch Settings TS10 - Single Signal Applications TS12 Control Switch Settings TS12 - Multi-Signal Applications TS14 - Control Switch Settings TS14 - Multi-Signal / Intersection Applications Warranty Information & Return Form Page 1 of 22 Release Date

2 GENERAL SPECIFICATIONS (**) Dimensions: AC Power: Fuse: Wire Size: Output Power: Time Delay: Time Adjustment:* Circuit Board Size TS10 Series - 3 x 3 (2.5" x 2.5" screw mounting) TS12 Series - 3 x 3.5 (2.5" x 3" screw mounting) TS14 Series - 4" x 5" (3.5" x 4.5" screw mounting) 120VAC - Fused TS10 Series - 2A Max. TS12 / 14 Series - 3A Max. (TS14 - x2 locations) (%) (220VAC Optional - available by request) TS10 Series - 5x20mm 250V/2A TS12 / 14 Series - 5x20mm 250V/3A AWG - Recommended TS10 / VAC / 150W Max. - Each Channel (^) TS14-120VAC / 120W Max. - Each Channel (^) See control switch settings, by control model. Counter-Clockwise = Slow Clockwise = Fast TS14 Time Delay -Left - Adjusts timing for signals #1 & #2. Time Delay-Right - Adjusts timing for signals #3 & #4. %Note: *Note: ^Note: **Note: TS14 - Fuse 1 protects signal outputs #1 & #2. Fuse 2 protects signal outputs #3 & #4, and control circuit. Time adjustment is single turn, similar to radio volume knob. Do not force beyond stopping points, as this will cause permanent damage. Output power is compatible with both L.E.D. and incandescent lighting. NOT RECOMMENDED FOR INDUCTIVE LOADS. General specifications are subject to change without notice. Page 2 of 22 Release Date

3 INSTALLATION & SAFETY TIPS 1. Warning! - Never handle control unit while powered on. 2. Do not install in damp, or wet environments. 3. Only replace fuse with equivalent size and rating. 4. Remove power for bulb replacement and/or servicing of any type. 5. Do not overload outputs beyond maximum rated specification Watts. 6. When connecting more than one incandescent bulb to a single output, divide the desired bulb wattage by 150 Watts. The result will be the number of bulbs of the desired wattage that can be used on a single output. Example: How many 40 Watt bulbs can I connect to a single output rated at 150 Watts? 150 Watts / 40 Watts = 3.75 ~ 3x - 40 Watt bulbs The number of 40 Watt bulbs that can be connected to a single output without overload is For AC power connection, follow the wiring diagram below. Page 3 of 22 Release Date

4 8. If your signal is equipped with a screw-terminal block, you may reference the following diagram. 9. If your signal is not equipped with a screw-terminal block, you may reference the following diagram(s). Page 4 of 22 Release Date

5 Page 5 of 22 Release Date

6 CONTROL MOUNTING 1. Before mounting, be sure mounting surface area is smooth, clean, dry, & oil free. 2. Be sure mounting location allows enough clearance area around the control unit, where metal components will not come into contact with the bottom, or components on the top side of the control unit. 3. Do not route wiring underneath control unit. RIGHT / CORRECT!!! WRONG / INCORRECT!!! Page 6 of 22 Release Date

7 TS10 CONTROL SWITCH SETTINGS Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Note: Reduced bulb wattage may be required when using Overlap functions / settings. Page 7 of 22 Release Date

8 TS10 CONTROL SWITCH SETTINGS (Continued) Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Note: Reduced bulb wattage may be required when using Overlap functions / settings. Page 8 of 22 Release Date

9 TS10 CONTROL SWITCH SETTINGS (Continued) ( School Zone / 2/4 Way Caution signals & RxR signals) Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Warning!: Railroad signals must be converted to operate on 120VAC. Note: Reduced bulb wattage may be required when using Overlap functions / settings. Page 9 of 22 Release Date

10 Application: TS10 - Single G,Y,R Signal Application: TS10 - Pedestrian / Crosswalk Signal Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Page 10 of 22 Release Date

11 Application: TS10 - School Zone w/ Lighted MPH, or 2/4-Way w/ Street Light, or RxR Signal Warning!: Railroad signals must be converted to operate on 120VAC. Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Page 11 of 22 Release Date

12 TS12 CONTROL SWITCH SETTINGS Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Note: Reduced bulb wattage may be required when using Overlap functions / settings. Page 12 of 22 Release Date

13 TS12 CONTROL SWITCH SETTINGS (Continued) Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Push button option is standard on all current TS12's manufactured after All TS12's manufactured between and that do not support the push button option, a firmware upgrade is available. Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Note: Reduced bulb wattage may be required when using Overlap functions / settings. Page 13 of 22 Release Date

14 Application: TS12 - Dual G,Y,R Signals / 2-Way Signaling, or G,Y,R & Arrow(s) Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Application: TS12 - Quad G,Y,R Signals / 4-Way Signaling. Page 14 of 22 Release Date

15 Application: TS12 Doghouse G,Y,R & 1, or 2 Arrow(s) - 4, or 5 Light Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. Application: TS12 Single G,Y,R Signal w/ Crosswalk Page 15 of 22 Release Date

16 Application: TS12 Dual PED / Crosswalk Signals, 2/4 Way Signaling. Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL WHILE POWERED ON. SPECIFICATIONS: (QUICK REFERENCE) REFER TO PAGE 2 FOR MOE DEATAILS. Dimensions: Wire Size: Input Power: Circuit Board Size TS10 Series - 3 x 3 (2.5" x 2.5" screw mounting) TS12 Series - 3 x 3.5 (2.5" x 3" screw mounting) TS14 Series - 4" x 5" (3.5" x 4.5" screw mounting) AWG - Recommended 120VAC - Fused TS10-2A Max. TS12 / 14-3A Max. (TS14 - x2 locations) (%) Output Power: TS10 / VAC / 150W Max. - Each Channel (^) TS14-120VAC / 120W Max. - Each Channel (^) Time Adjustment:* Counter-Clockwise = Slow Clockwise = Fast *Note: Time adjustment is single turn, similar to radio volume knob. Do not force beyond stopping points, as this will cause permanent damage. ^Note: Output power is compatible with both L.E.D. and incandescent lighting. NOT RECOMMENDED FOR INDUCTIVE LOADS. Page 16 of 22 Release Date

17 TS14 CONTROL SWITCH SETTINGS Page 17 of 22 Release Date

18 Application: TS14-2x G,Y,R Signaling + 2x PED Signaling Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL UNIT WHILE POWERED ON. Page 18 of 22 Release Date

19 Application: TS14 1x G,Y,R, + 1x PED & G,Y,R w/ Arrows (Non-protected) Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL UNIT WHILE POWERED ON. Page 19 of 22 Release Date

20 Application: TS14 1x G,Y,R, + 1x PED & G,Y,R w/ Arrows (Protected) OR 3x G,Y,R, + 1x PED Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL UNIT WHILE POWERED ON. Page 20 of 22 Release Date

21 Application: TS14 4x G,Y,R, and/or G,Y,R w/ Arrows Warning!: SHOCK HAZARD! DO NOT HANDLE CONTROL UNIT WHILE POWERED ON. Page 21 of 22 Release Date

22 WARRANTY / RETURN FORM MODEL: TS10/T TS12/P TS14 OTHER PURCHASE DATE: (Please Specify Model) 1 YEAR - LIMITED WARRANTY All TS series are warranted against manufacturing/workmanship defects for a period of 1 year from date of purchase. Any TS series control that is used for other than the purpose intended, resulting in damage, personal or property, is the rightful owners responsibility. This warranty does not cover, improper installation /application, modification, misuse, abuse, power surge, brown outs, lightning strikes, and any other act of god resulting in damage, whether personal or property. TS series controls are designed for indoor and private use only. And, are not intended for industrial / commercial, or municipality use. Return Policy: TS Series controls returned for refund, or repair, without proof of purchase will not be honored under warranty. TS series controls under warranty will be repaired/replaced, at the discretion of the manufacturer, as necessary. Any TS series control returned for repair after warranty period, out of warranty will be repaired at a flat rate cost of $20, and will be warranted for a period of 30 days. Mail / Remit to: Brent Anderson 2725 Castleton Ave. Toledo, OH Directions: Complete the requested information below. Name: Address: City-State-Zip: Phone#: ( ) (optional): (Please Check) Reason for return / description of failure / problem. Repair / Exchange Refund (See Return Pol icy) Page 22 of 22 Release Date