Phone: Fax: REGULATOR-1ST 3/4" FPT X 3/4" FPT 2.4M BTU 8-12 PSI REGULATOR-1ST STAGE COMPACT POL X 3/4"NPT 8-12 PSIG SPRING

Transcription

1 Regulators Fisher First Stage The R122H and R622H first stage regulators are UL listed regulators designed for two stage LP gas regulator systems. These first stage regulators reduce tank pressure to a lower pressure (usually 10 psig or 0,69 bar) for a second stage regulator. Fisher first stage regulators are painted red for easy identification. Vents are screened with standard orientation over the outlet. The R122H and R622H regulators have a temperature rating of -20 to 160 F, but have passed Fisher internal testing for lockup, relief start to discharge and reseal down to -40 F. Type R122H - Designed for use as a first stage regulator for domestic applications, the R122H's size makes it perfect for tight installations. Stainless steel internal parts and corrosion resistant coatings provide a recommended replacement life of 20 years. Its nonadjustable set point makes the unit virtually tamper proof. Inlet and outlet gauge taps allow easy system testing. Large inlet and outlet wrench flats provide for easy installation, even in underground tanks. The outlet pressure set point remains at a nominal factory setting of 10 psig (0,69 bar). The design's superior relief performance exceeds UL requirements and provides double failure overpressure protection when used with a Fisher R600 second stage regulator. The unit's fluorocarbon valve disc provides better lockup performance and durability in contaminated gas. The vent is threaded with 3/8" NPT for easy installation of vent piping. A large fabric reinforced diaphragm provides accurate regulation. The large orifice assists in minimizing freeze problems. Type R622H - Time proven design constructed of corrosion resistant and wear resistant materials, the R622H is designed to provide a recommended replacement life of 20 years. Built-in 1/8" FNPT gauge taps on both the inlet and outlet pressure sides allow for easy system checks. A large 3/4" FNPT drip lip vent reduces the chance of blockage by freezing rain or sleet when properly installed with the vent pointing down. Each R622H is equipped for overpressure protection with a corrosion resistant internal relief valve that provides high capacity relief and a travel stop on the closing cap. Its size and configuration make it ideal for under the dome installations. Type R622H - A first stage regulator with 65% higher flow than typical compact regulators and with 40% small footprint for underground tanks or limited dome space. It is Underwriters Laboratories (UL) listed for LP gas systems. It comes with multiple end connections, adjustable spring ranges, and corrosion resistant materials. It has been tested to -40 F/-40 C. LP-R122H-AAJ LP-R222H-HGJ LP-R222H-JGJ LP-R622H-BGK LP-R622H-HGK LP-R622H-JGK LP-R622H-BGJ LP-R622H-DGJ LP-R622H-HGJ LP-R622H-JGJ REGULATOR-1ST 1/4" FPT X 1/2" FPT 1.1M BTU 10PSI REGULATOR-1ST STAGE COMPACT POL X 1/2" NPT 8-12 PSIG SPRNG REGULATOR-1ST STAGE COMPACT POL X 3/4"NPT 8-12 PSIG SPRING REGULATOR-1ST 1/2" FPT X 1/2" FPT 2.0M BTU 4-6 PSI REGULATOR-1ST FML POL X 1/2" FPT 2.0M BTU 4-6 PSI REGULATOR-1ST FML POL X 3/4" FPT 2.25M BTU 4-6 PSI REGULATOR-1ST 1/2" FPT X 1/2" FPT 2.1M BTU 8-12 PSI REGULATOR-1ST 3/4" FPT X 3/4" FPT 2.4M BTU 8-12 PSI REGULATOR-1ST FML POL X 1/2" FPT 2.1M BTU 8-12 PSI REGULATOR-1ST FML POL X 3/4" FPT 2.25M BTU 8-12 PSI 1

2 Regulators Fisher Second Stage The R222, R622, R642, R652 and HSRL second stage regulators are UL listed regulators designed to reduce the outlet pressure from a first stage regulator, usually 10 psig (0.69 bar) to 11" water column (27 mbar), in domestic installations. Vents are screened with standard orientation over the inlet but other orientations are available. Fisher second stage regulators are painted palm green for easy identification. Fisher types R222, R622, R642 and R652 are equipped with a stainless steel inlet screen to reduce the amount of debris entering the regulator and have a temperature rating of -20 to 160 F, but have passed Fisher internal testing for lockup, relief start-to-discharge and reseal down to -40 F. LP-R222-BAF LP-R622-BCF LP-R622-CFF LP-R622-DFF LP-R622-CFFXA LP-R622-DFFXB LP-R642-DFF LP-R652-CFF LP-R652-DFF LP-HSRL-BFC LP-HSRL-CFC REGULATOR-2ND 1/2" FPT X 1/2" FPT 650K BTU 9.5"-13" WC REGULATOR-2ND 1/2" FPT X 1/2" FPT 875K BTU 9"-13" WC REGULATOR-2ND 1/2" FPT X 3/4" FPT 1.4M BTU 9"-13" WC REGULATOR-2ND 3/4" FPT X 3/4" FPT 1.4M BTU 9"-13" WC REGULATOR-2ND 1/2" FPT X 1/2" FPT 1.4M BTU 9"-13" WC VNT OVR REGULATOR-2ND 3/4" FPT X 3/4" FPT 1.4M BTU 9"-13" WC VND OVR REGULATOR-2ND 3/4" FPT X 3/4" FPT 920K BTU 9"-13" WC REGULATOR-2ND 1/2" FPT X 3/4" FPT 1.0M BTU 9"-13" WC REGULATOR-2ND 3/4" FPT X 3/4" FPT 1.0M BTU 9"-13" WC REGULATOR-2ND 3/4" FPT X 3/4" FPT 2.3M BTU 9"-13" WC REGULATOR-2ND 1" FPT X 1" FPT 2.6M BTU 9"-13" WC 2

3 Regulators Fisher 2 PSI Type R622E and R652E are 2 psi service regulators that are installed downstream from a first stage regulator and reduce an inlet pressure of 10 psig (0.69 bar) to a nominal 2 psig (0.14 bar) outlet pressure. Two psi service regulators are designed for domestic applications that supply to a line regulator located inside the building. In most cases a manifold is used with corrugated stainless steel tubing (CSST) as well as other acceptable piping materials for routing to the line pressure regulator supplying approximately 11 inches w.c. (27 mbar) to appliance regulators. Types R622E and 652E feature a combination relief valve and large vent that provides overpressure protection and exceed UL requirements. Both units have a stainless steel inlet screen to reduce the amount of debris from entering them. Fisher types R622E and R652E are painted green with a white closing cap for easy identification and have a temperature rating of -20 to 160 F, but have passed Fisher internal testing for lockup, relief start to discharge seal down to -40 F. Type R622E Time proven design constructed of corrosion resistant materials, is designed to provide a recommended replacement life of 20 years. Fisher s fabric reinforced diaphragm and large diaphragm area provide accurate regulation at increased capacities. All components provide superior resistance to field conditions that may cause wear and corrosion. Built-in 1/8 taps (orificed to a number 54 drill size) on the upstream and downstream sides allow for easy gas system checks. Type R652E provides the same features as the type R622E, includes a 20 year recommended replacement life with a back mount design. LP-R622E-BCH LP-R622E-DCH LP-R652E-DFH REGULATOR-2PSI 1/2" FPT X 1/2" FPT 1.46M BTU PSI REGULATOR-2PSI 3/4" FPT X 3/4" FPT 1.68M BTU PSI REGULATOR-2 PSI 3/4" FPT X 3/4" FPT 1.5M BTU PSI 3

4 Regulators Fisher Integral Two Stage Integral two stage regulators combine a first stage regulator and a second stage regulator into one compact unit. Recommended for installations where piping distance is short, integral two stage regulators provide all of the advantages of two stage regulation. Fisher integral two stage regulators are color coded gray for easy identification. Vents are screened with standard second stage vent orientation over the outlet. Type R632A first stage screened vent is threaded to accept a ¼" OD copper tube inverted flare with a 7/16-24 UN thread. R632A also has a temperature rating of -20 to 160 F, but have passed Fisher internal testing for lockup, relief start to discharge and reseal down to -40 F. Type R232A - Designed for installations with small capacity loads up to 550,000 Btu/hr (6.2 SCMH). With an overall length of 6.5" or 7" for NPT or FPOL connections respectively, this compact unit fits easily into confined spaces and is ideal for ASME tanks used on small domestic loads. Intermediate and outlet gauge taps facilitate easy system testing. A threaded 3/8" NPT vent allows easy installation of vent piping. Use of a valve stem and lever provide stable regulation and excellent durability. A large fabric reinforced diaphragm provides accurate regulation. The large orifice assists in minimizing freeze problems. Stainless steel internal and corrosion resistant coatings provide excellent corrosion resistance. Type R232A also has the design that provides a recommended replacement life of 20 years. Twin Cylinder Installations - The R232A can also be used on twin cylinder hook ups found on travel trailers and stationary applications. These units offer a drip lip vent style for installations without a vent protector. Proper installation requires the vent to be pointed down in a vertical position. Additional protection may be required if road splatter is a problem. Type R632A is a UL listed regulator with a capacity of up to 950,000 Btu/hr (10.7 SCMH). It is recommended for onsite cylinder installations, mobile homes and domestic installations where separation of the first and second stage is not cost effective. This unit offers a POL inlet connection for the easy drop in replacement of single stage regulators. LP-R232A-BBF LP-R232A-HBF LP-R632A-BCF LP-R632A-CFF LP-R632A-HCF LP-R632A-JFF REGULATOR-INTEGRAL 1/4" FPT X 1/2" FPT 550K BTU 9.5"-13" WC REGULATOR-INTEGRAL FML POL X 1/2" FPT 550K BTU 9.5"-13" WC REGULATOR-INTEGRAL 1/4" FPT X 1/2" FPT 850K BTU 9"-13" WC REGULATOR-INTEGRAL 1/4" FPT X 3/4" FPT 950K BTU 9"-13" WC REGULATOR-1ST & 2ND FML POL X 1/2" FPT 850K BTU 11" WC REGULATOR-INTEGRAL FML POL X 3/4" FPT 850K BTU 9"-13" WC 4

5 Regulators Fisher Integral 2 PSI Integral two psi regulators combine a first stage regulator and a second stage regulator into one compact unit. Recommended for installations where piping distance is short, integral two stage, two psi regulators provide all of the advantages of two stage regulation. Fisher integral two stage, two psi regulators are color coded gray with a white cap and white UV cover for easy identification. Vents are screened with standard second stage vent orientation over the outlet. Types R232E and R632E first stage screened vent is threaded to accept a ¼" OD copper tube inverted flare with a 7/16-24 UN thread and have a temperature rating of -20 to 160 F, but have passed Fisher internal testing for lockup, relief start to discharge and reseal down to -40 F. Type R232E - Designed for installations with small capacity loads up to 450,000 Btu/hr. With an overall length of 6.5" or 7" for NPT or FPOL connections respectively, this compact unit fits easily into confined spaces and is ideal for ASME tanks used on small domestic loads. Intermediate and outlet gauge taps facilitate easy system testing. A threaded 3/8" NPT vent allows easy installation of vent piping. Use of a valve stem and lever provide stable regulation and excellent durability. A large fabric reinforced diaphragm provides accurate regulation. The large orifice assists in minimizing freeze problems. Stainless steel internal and corrosion resistant coatings provide excellent corrosion resistance. Type R232E also has the design that provides a recommended replacement life of 20 years. Twin Cylinder Installations - The R232A can also be used on twin cylinder hook ups found on travel trailers and stationary applications. These units offer a drip lip vent style for installations without a vent protector. Proper installation requires the vent to be pointed down in a vertical position. Additional protection may be required if road splatter is a problem. Type R632E is a UL listed regulator with capacity of up to 810,000 Btu/hr (9.1 SCMH) recommended for onsite cylinder installations, mobile homes and domestic installations where separation of the first and second stage is not cost effective. This unit offers a POL inlet connection for the easy drop in replacement of single stage regulators. The R632E s high capacity relief valve and large ¾" screened vent limit downstream pressure to less than 5 psig (0.34 bar) in an overpressure situation as required by NFPA 58. Type R632E is adjustable from 1 to 2.2 psig (69 to 152 mbar) with a factory set point of 11" w.c. (27 mbar) and features a 20 year recommended replacement life. Type R632E has 1/8" NPT built-in gauge taps, orificed to a No. 54 drill size on the upstream and downstream sides. These taps provide easy access for testing the proper operation pressure of the first and second stage while the system is pressurized. This regulator also features a large ¾" drip lip vent to reduce the chance of blockage by freezing rain or sleet when properly installed with the vent pointing down. LP-R232E-HBH LP-R632E-HCH REGULATOR-INTEG 2PSI FML POL X 1/2" FPT 500K BTU PSI REGULATOR-INTEG 2PSI FML POL X 1/2" FPT 900K BTU PSI 5

6 Regulators Fisher High Pressure Industrial 67 Series 67C Series - Suitable for liquid or vapor service, the 67C series high pressure (pounds to pounds) regulators are used on a variety of applications. All types within the series have 1/4" FNPT side outlet in which a pressure gauge (J500 series) can be installed. The compact size of the 67C makes it particularly useful on installations where space is limited. The regulator design utilizes precise guiding of the valve plug to provide close regulation and high performance. The 67C series has a temperature rating of -20 to 180 F. Type 67CW Standard regulator with wrench adjustment. Type 67CH Standard regulator with handwheel adjustment. Type 67CD With dial calibration accuracy nearly equivalent to that of a commercial pressure gauge, the 67CD eliminates the need for a pressure gauge on portable applications. Outlet pressure is calibrated on the spring case allowing visual adjustment of the outlet pressure. The unit is ideal for service where gauge breakage is a problem. Type 67CN Extremely compact unit with a fixed nonadjustable outlet setting and a tamper resistant spring case. Three different set points are available, 10, 15 and 20 psig (0.69, 1.0 and 1.4 bar). Note: 67C Series regulators do not have an internal relief and should be installed with additional external overpressure protection. These units should not be installed in fixed piping service 14" w.c. (35 mbar) appliance systems. Please consult with FEI Customer Service for more information. LP-67CW-684 LP-67CW-685 LP-67CH-743 LP-67CH-742 LP-67CH-741 LP-67CD-101 LP-67CD-102 LP-67CN-105 REGULATOR-1ST 1/4" FPT 750K BTU 3-35 PSI REGULATOR-1ST 1/4" FPT 1.2M BTU PSI REGULATOR-1ST 1/4" FPT 750K BTU 3-35 PSI REGULATOR-1ST 1/4" FPT 1.2M BTU PSI REGULATOR-1ST 1/4" FPT 1.0M BTU PSI REGULATOR-1ST 1/4" FPT 675K BTU 5-20 PSI REGULATOR-1ST 1/4" FPT 1.2M BTU PSI REGULATOR-1ST 1/4" FPT 750K BTU 20 PSI 6

7 Regulators Fisher High Pressure Industrial 64 Series 64 Series - High pressure (pounds to pounds) regulators usually reduce tank pressure to an intermediate pressure for use by another regulator. They may be used as high pressure regulators on distribution systems when used in conjunction with a first stage downstream regulator. The 64SR may be used for first stage when set at 10 psig (0.69 bar). They are also used for final stage service on high pressure burners in crop dryers and tobacco curers as well as other medium sized commercial and industrial applications. The 1/4" FNPT side outlet, which is normally plugged, provides an opening for an outlet pressure gauge. The standard 64 series is capable of handling liquid or vapor at temperatures under 150 F. A cover or auxiliary vent assembly should be used to protect the 1/4" FNPT regulator vent opening on outdoor installations. Temperature rating for the 64 and 64SR series is from -20 to 150 F. Type 64 is an adjustable high pressure regulator with a wide range of available outlet pressure ranges. It does not contain a relief valve. It should always be used in conjunction with a downstream regulator and/or separate relief devices in compliance with NFPA 58 overpressure protection requirements. Note: 64 Series regulators do not have an internal relief and should be installed with additional external overpressure protection. These units should not be installed in fixed piping service 14" w.c. (35 mbar) appliance systems. Please consult with FEI Customer Service for more information. Type 64SR is a high pressure regulator which has an internal relief valve. As such it may be used as a final stage regulator on high pressure systems. It may also be used as a first stage regulator when set at 10 psig (0.69 bar) or less. Note: If the installation location makes the ignition of vented gas a possibility, then a vent line should be installed from the 64SR to vent to a safe location. LP LP LP LP LP-64SR-21 LP-64SR-22 LP-64SR-23 REGULATOR-1ST 1/2" FPT 2.625M BTU 3-15 PSI REGULATOR-1ST 1/2" FPT 3.6M BTU 5-35 PSI REGULATOR-1ST 1/2" FPT 4.15M BTU PSI REGULATOR-1ST 1/2" FPT 5.25M BTU PSI REGULATOR-1ST 1/2" FPT 2.625M BTU 3-15 PSI W/ RELIEF REGULATOR-1ST 1/2" FPT 3.0M BTU 5-20 PSI W/RELIEF REGULATOR-1ST 1/2" FPT 3.6M BTU 5-35 PSI W/RELIEF 7

8 Regulators Fisher Low Pressure Commercial CS200 Series Type CS200 - The type CS200 is a medium capacity low pressure, direct operated regulator designed for loads up to 3,800,000 Btu/hr (44 SCMH), ideal for installations on smaller commercial or industrial applications. Available in 3/4", 1" and 1-1/4" body sizes with spring ranges from 3.5" w.c. to 2 psig (9 mbar to 0.14 bar). LP-CS200IR-6HC3 LP-CS200IR-6EC6 REGULATOR-1" FNPT CI 1/2" PORT INT/RELIEF 1-2 PSI REGULATOR-2ND 1-1/4" FPT 3.9M BTU 1/2" ORIFICE 10-14" WC CS400 Series Type CS400 - The type CS400 is a medium capacity low pressure, direct operated regulator designed for loads up to 7,800,000 Btu/hr (88 SCMH), ideal for installations at schools, bakeries and many other commercial and industrial application. Available in 1-1/4", 1-1/2" and 2" body sizes with spring ranges from 4.5" w.c. to 5.5 psig (11mbar to 0.38bar). LP-CS400IR-8EC6 LP-CS400IR-8EC7 LP-CS400IR-8EC8 LP-CS400IR-8HC6 LP-CS400IR-8HC7 LP-CS400IR-6IC6 LP-CS400IR-8IC6 LP-CS400IR-8IC8 LP-CS403IT-8DD2 LP-CS403IT-8DD4 REGULATOR-2ND 1-1/4" FPT 6.8M BTU 3/4" ORIFICE 10-14" WC REGULATOR-2ND 1-1/2" FPT 7.6M BTU 3/4" ORIFICE 10-14" WC REGULATOR-2ND 2" FPT 7.6M BTU 3/4" ORIFICE 10-14" WC REGULATOR-2ND 1-1/4" FPT 9.8M BTU 3/4" ORIFICE 1-2 PSI REGULATOR-2ND 1-1/2" FPT 10.5M BTU 3/4" ORIFICE 1-2 PSI REGULATOR-2ND 1-1/4" FPT 4.0M BTU 1/2" ORIFICE PSI REGULATOR-2ND 1-1/4" FPT7.365M BTU 3/4" ORIFICE PSI REGULATOR-2ND 2" FPT 7.365M BTU 3/4" ORIFICE PSI REGULATOR-1-1/4" FNPT DUCTILE IRON LP W/MONITOR 3/4" PORT REGULATOR-2" FNPT DUCTILE IRON LP W/MONITOR 3/4" PORT CS800 Series Type CS800 - The type CS800 is a direct operated, spring loaded regulator which has been engineered for low pressure commercial service applications. This regulator can accommodate up to 21,600,000 Btu/hr (243 SCMH) flow capacity and is available in 1-1/2" and 2" body sizes with 8" water column to 5.5 psig (20 mbar to 0.38 bar) pressure ranges. LP-CS800IR-8BC7 LP-CS800IR-8CC8 LP-CS800IR-8DC7 LP-CS800IR-8DC8 LP-CS820IR-8GC8 LP-CS820IR-8HC8 REGULATOR-2ND 1-1/2" FPT 30 PSI 1" ORIFICE REGULATOR-2ND 2" FPT M BTU 1" ORIFICE 8-12" WC REGULATOR-2ND 1-1/2" FPT9.427M BTU 1" ORIFICE 10-16" WC REGULATOR-2ND 2" FPT 18M BTU 1" ORIFICE 10-16" WC REGULATOR-2ND 2" FPT 15M BTU 1" ORIFICE PSI REGULATOR-2" FPT CI 2.5 TO 5.5 PSI 1" PORT W/RELIEF 8

9 Regulators Fisher Low Pressure Commercial CS800 Series 9

10 Regulators Fisher Low Pressure Commercial 299H Series Type 299H A high capacity pilot operated regulator that incorporates a lightweight design (21 lbs.) with dependable operation. With a capacity up to 38,000,000 Btu/hr (428 SCMH), the 299H is ideal for applications from large commercial sites to smaller multi-dwelling establishments. The unit comes with a 1-1/2" or 2" cast iron body with internal or external registration. Internal registration allows easy installation while external registration provides higher accuracy. 2" (DN 50) flanged body or steel body material also available. Alternate outlet settings from 3.5" w.c. to 60 psig (9 mbar to 4.1 bar) are available. Temperature ratings for 299H are -20 to 150 F. The 299H has a maximum inlet pressure rating of 150 psig (10 bar) so it cannot be used as a first stage regulator. LP-299H-102 LP-299H-104 LP-299H-106 LP-299H-NBK 133 Series REGULATOR-2ND 2" FPT 19.7M BTU 3/4" ORIFICE 7-20" WC REGULATOR-2ND 2" FPT 38M BTU 3/4" ORIFICE 5-16 PSI REGULATOR-2ND 2" FPT 20.4M BTU 3/4" ORIFICE 9-20" WC REGULATOR-2ND 2" FPT 30M BTU 1" ORIFICE PSI Type 133 Direct operated second stage regular ideal for large industrial applications with loads up to 70,875,000 Btu/hr. (798 SCMH). The unit can be used for either low pressure or pounds service. Maximum inlet pressure is 60 psig (4.1 bar) and a downstream control line is required. The 133 series has a temperature rating of -20 to 150 F. LP-133L-4 LP-133H-1 REGULATOR-2ND 2" FPT M BTU 2" ORIFICE " WC REGULATOR-1ST 2" FPT 66M BTU 2" ORIFICE PSI 10

11 Regulators Fisher High Pressure Commercial 627 Series Type 627 and 630 are large capacity direct operated high pressure regulators designed for loads up to 10,700,000 and 14,000,000 Btu/hr (120 and 157 SCMH) respectively. The 627 and 630 are normally used in conjunction with type CS400 however they can also be used on final stage (pounds to pounds) service. Additional overpressure protection is recommended to prevent excessive build up in the downstream line. The diaphragm case and body can be rotated in four positions to allow easy installation. Additional configurations with internal relief and control line connections for monitor systems are available. Additional pressure ranges and orifice sizes are available. Temperature ratings are -20 to 160 F. LP LP LP LP-627M-421 LP-627M-471 LP-627R-113 LP LP REGULATOR-1ST 3/4" FPT 6.08M BTU 3/8" ORIFICE 5-20 PSI REGULATOR-1ST 3/4" FPT M BTU 1/2" ORIFICE 5-20 PSI REGULATOR-1ST 1" FPT M BTU 1/2" ORIFICE 5-20 PSI REGULATOR-1ST 3/4" FPT M BTU 1/2" ORIFICE 5-20 PSI REGULATOR-1ST 1" FPT M BTU 1/2" ORIFICE 5-20 PSI REGULATOR-1ST 3/4" FPT 10.7M BTU 3/8" ORIFICE 5-20 PSI REGULATOR-1ST 3/4" FPT 1/2" PORT PSI REGULATOR-1ST 2" FPT 20.9M BTU 1/2" ORIFICE PSI 630 Series LP /78 REGULATOR-1ST 2" FPT 14M BTU 1/2" ORIFICE 8-20 PSI 11

12 Regulators Fisher High Pressure Commercial 99 Series The 99 Series is for commercial and industrial high pressure applications. For ease of reference, only the most popular commercial and industrial regulators are shown. Other orifice sizes, body sizes and outlet pressure ranges are available. The higher capacities on commercial and industrial installations usually require a two stage regulator system. Note: Because of various spring ranges and orifice sizes, all commercial and industrial regulators should be individually sized for the particular installation. Consult specific product bulletins for maximum pressure ratings. Contact FEI Customer Service for assistance. Type 99 Pilot operated unit keeps outlet pressure constant despite varying flow rates and inlet pressures. Designed to handle loads up to 74,318,000 Btu/hr (837 SCMH), the 99 series is ideal for multiple customer installations. The unique pilot design with fast opening and closing operation makes it ideal for large industrial boiler applications. The 99 series can be used for low or high pressure applications. A downstream control line is required. Additional overpressure protection is recommended to prevent excessive buildup in the downstream line. Note: Series 99 regulators do not have an internal relief and should be installed with additional external overpressure protection. These units should not be installed as part of a two stage system in fixed piping serving 14" w.c. (35 mbar) appliance systems unless additional overpressure protection is installed that will make the system compliant with NFPA 58 requirements for a two stage system. Please consult FEI Customer Service for more information. Flanged Bodies 99F Series is equipped with 2" CL300 flanged bodies. Overpressure Protection The type 99 is also available in monitor configurations. Note that the type 99 monitor regulators have unique type numbers. LP P LP P LP P LP P LP PH LP PH LP PH LP PH REGULATOR-1ST 2" FPT M BTU 7/8" ORIFICE 2-10 PSI REGULATOR-1ST 2" FPT 37.95M BTU 7/8" ORIFICE 5-15 PSI REGULATOR-1ST 2" FPT M BTU 7/8" ORIFICE PSI REGULATOR-1ST 2" FPT M BTU 7/8" ORIFICE PSI REGULATOR-1ST 2" FPT M BTU 1-1/8" ORIFICE 2-10 PSI REGULATOR-1ST 2" FPT 63.25M BTU 1-1/8" ORIFICE 5-15 PSI REGULATOR-1ST 2" FPT M BTU 1-1/8" ORIFICE PSI REGULATOR-1ST 2" FPT M BTU 1-1/8" ORIFICE PSI 12

13 Regulators Fisher High Pressure Commercial 99 Series 13

14 Regulators Fisher Compact Regulators Fisher Small portable appliance regulators Type 912 are designed for use on small portable outdoor appliances with capacity ratings of less than 100,000 Btu/hr. Underwriters Laboratory requires horizontally mounted regulators to be installed with vent opening protection to prevent blockage by freezing rain. Vent protector Type P331 can be used on a horizontally mounted Type 912. The 912 series has a temperature rating of -20 to 160 F. Capacities are based on 10 psi inlet pressure. LP-912/101 LP-912/104 LP-912N/109 LP REGULATOR-SINGLE 1/4" FPT X 3/8" FPT 110K BTU 1/4-13" WC REGULATOR-SINGLE 1/4" FPT X 1/4" FPT 101L BTU 1/4-13" WC REGULATOR-SINGLE 1/4" FPT X 3/8" FPT 123K BTU 5-10" WC REGULATOR-SINGLE 1/4" FPT X 3/8" FPT 101K BTU 12-24" WC 14

15 Regulators Marshall Excelsior First Stage These first stage regulators are used to reduce LP gas tank pressures for a second stage regulator (normally 10 psig). All MEC first stage regulators are red, indicating high outlet pressure. Compact first stage regulator vents have 3/8" FNPT tapped ports and E-Z grip screens located over the outlet. The MEGR-1222H series offers relief performance that exceeds UL test requirements providing double failure overpressure protection when used with MEC MEGR-1622, MEGR-1642 and MEGR-1652 series second stage regulators. All MEC Excela- Flo domestic regulators feature a 25 year recommended replacement life and an exclusive 3 part tear away leak check adhesive sticker. MEGR-1122H and MEGR-1222H Series offer a compact first stage regulator design perfect for tight applications such as underground tank domes. They feature an adjustment range from 9-12 psig (factory set at 10 psig), stainless steel internal components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms and large aluminum precision machined orifice to minimize freeze ups while providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. MEGR-1622H Series offers all of the same features as the compact MEGR-1122H series in a full size version. The MEGR-1622H series has a large fabric reinforced diaphragm for superior downstream regulation, heavy duty wrench flats, and a large 3/4" FNPT tapped drip lip vent to help prevent relief vent blockage. LP-MEGR-1122H-AAJ LP-MEGR-1222H-BGF LP-MEGR-1622H-BGK LP-MEGR-1622H-HGK LP-MEGR-1622H-JGK LP-MEGR-1622H-BGJ LP-MEGR-1622H-DGJ LP-MEGR-1622H-HGJ LP-MEGR-1622H-JGJ LP-MEGR-1222HT-BGF LP-MEGR-1622HT-HGJ LP-MEGR-1622HT-JGJ REGULATOR-1ST 1/4" X 1/2" FPT 10 PSI 1,100,111 BTU REGULATOR-1ST STAGE COMPACT FML POL X 1/2" FPT OUT 10PSI REGULATOR-1ST 1/2" FNPT X 1/2" FNPT 5 PSI REGULATOR-1ST FPOL X 1/2" FNPT 10 PSI REGULATOR-1ST F.POL X 3/4"FNPT 5 PSI REGULATOR-1ST 1/2" FPT X 1/2" FPT 10 PSI 2,100,000 BTU REGULATOR-1ST 3/4" FPT X 3/4" FPT 10 PSI 2,400,000 BTU REGULATOR-1ST POL X 1/2" FPT 10 PSI 2,100,000 BTU REGULATOR-1ST POL X 3/4" FPT 10 PSI 2,250,000 BTU REGULATOR-1ST STAGE COMPACT FMLPOL X 1/2"FPT 10PSI TEE INL REGULATOR-1ST F.POL X 1/2"FNPT 10 PSI TEE INLET REGULATOR-1ST F.POL X 3/4" FPT 10 PSI TEE INLET 15

16 Regulators Marshall Excelsior Second Stage These second stage regulators are used to reduce outlet pressures from first stage regulators (normally 10 PSI) to 11" WC in domestic installations. All MEC second stage regulators are green indicating low outlet pressure. Second stage full size regulator vents have 3/4" FNPT tapped ports and our exclusive E-Z grip screens located over the inlet. All MEC second stage domestic regulators feature a stainless steel inlet filter screen to reduce debris from passing through the regulator. Both the MEGR-1622 and the MEGR-1652 Series offer optimal relief performance that exceeds UL test requirements providing double failure overpressure protection (no more than 2 PSI downstream pressure) when used with MEGR-1122H and MEGR-1622H Series First Stage regulators. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive tear away leak check adhesive sticker. MEGR-1622 and MEGR-1652 Series offers all the same features as the compact MEGR-1122 Series but in a full size, high capacity version. Our full size second stage regulators have a large fabric reinforced diaphragm for superior downstream regulation, heavy duty wrench flats, and a large 3/4" FNPT tapped drip lip vent to help prevent relief valve blockage. The MEGR-1622 Series have both the inlet and outlet in line where the MEGR-1652 series have a rear discharge back mount outlet for convenient wall mount applications. MEGR-1222 and MEGR-1252 Series offers a compact second stage regulator design perfect for lower to intermediate BTU applications. They feature an adjustable range from " WC (factory 11" WC), stainless steel internal components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms and large aluminum precision machined orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. The MEGR Series have both the inlet and outlet in line where the MEGR-1252 series have a rear discharge back mount outlet for convenient wall mount applications. LP-MEGR-1222-BAF LP-MEGR-1222-CFF LP-MEGR-1222-DFF LP-MEGR-1252-BAF LP-MEGR-1252-CFF LP-MEGR-1252-DFF LP-MEGR-1622-BCF LP-MEGR-1622-CFF LP-MEGR-1622-DFF LP-MEGR-1642-DFF LP-MEGR-1652-CFF LP-MEGR-1652-DFF LP-MEGR-1HSRL-BFC LP-MEGR-1HSRL-CFC REGULATOR-2ND 1/2" FPT IN/OUT 650,000 BTU 11" WC REGULATOR-COMPACT HIGH CAP 2ND STAGE 1/2" X 3/4" 800K BTU REGULATOR-COMPACT HIGH CAP 2ND STAGE 3/4"X 3/4" 800,000 BTU REGULATOR-COMPACT 2ND STAGE 1/2" X 1/2" FNPT 11" WC OUTLET REGULATOR-COMPACT 2ND STAGE 1/2" X 3/4" FNPT 11" WC OUTLET REGULATOR-COMPACT HIGH CAP BAC MT 2ND STAGE 3/4"X 3/4"FPT REGULATOR-2ND 1/2" FPT IN/OUT 875,000 BTU 11" WC REGULATOR-2ND 1/2" FPT INLET 3/4" OUTLET 1.4M BTU 11" WC REGULATOR-2ND 3/4" FPT IN/OUT 1,400,000 BTU 11" WC REGULATOR-2ND 3/4" X 3/4" FPT REGULATOR-2ND 1/2" X 3/4" FPT 1,000,000 BTU 11" WC REGULATOR-2ND 3/4" X 3/4" FPT BACK MOUNT 1M BTU 11" WC REGULATOR-2ND 3/4" FPT IN/OUT 2,300,000 BTU 11" WC REGULATOR-2ND 1" FPT IN/OUT 2,600,000 BTU 11" WC 16

17 Regulators Marshall Excelsior 2 PSI These 2 PSI service regulators are used to reduce outlet pressures from first stage regulators (normally 10 PSI) to a nominal 2 PSI. 2 PSI service regulators are used in conjunction with an LPG line regulator either at the indoor appliance or a remote manifold distribution header inlet. All MEC 2 PSI service regulators are white with black adjustment caps. The full size 2 PSI service regulators have 3/4 FNPT tapped vents and our exclusive E-Z grip screens located over the inlet. All MEC 2 PSI service regulators feature a stainless steel inlet filter screen to reduce debris from passing through the regulator. Both the MEGR-1622E and MEGR-1652E series offer optimal relief performance that exceeds UL test requirements. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive tear away leak check adhesive sticker. MEGR-1622E Series offers a full size high capacity molded lip fabric reinforced diaphragm, stainless steel internal components, fluorocarbon (FKM) seat discs, precision machined aluminum orifices, and an adjustment range from PSI (factory 2 PSI) providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. MEGR-1652E Series offers all of the same features as the MEGR-1622E Series but with a rear discharge back mount outlet for convenient wall mount applications. LP-MEGR-1622E-BCH LP-MEGR-1622E-DCH LP-MEGR-1652E-DFH REGULATOR-2ND 1/2" FPT X 1/2" FPT 2 PSI 1,460,000 BTU REGULATOR-2ND 3/4" FPT X 3/4" FPT 2 PSI 1,680,000 BTU REGULATOR-2ND 3/4" X 3/4" FPT 2 PSI 1,500,000 BTU 17

18 Regulators Marshall Excelsior Integral Two Stage These integral two-stage regulators combine the first and second stage regulator set-up into one convenient unit converting full tank pressure to 11" WC. All MEC integral two-stage domestic regulators are gray indicating low outlet pressure. Integral two-stage regulators are recommended for installations with short piping distances, but provide the same advantages of two-stage regulation with a single unit. All MEC integral two-stage regulator vent have tapped ports (7/16-24-First Stage) (3/8" FNPT Second Stage Compact / 3/4" FNPT Second Stage Full Size) and our exclusive E-Z Grip screens located over the outlet. Both the MEGR-1232 and MEGR-1632 series offer optimal relief performance that exceeds UL test requirements providing over pressure protection of no more than 2 PSI downstream pressure. MEC Excela-Flo integral two-stage domestic regulators feature a 25 year recommended replacement life, our exclusive Tri-Tap (Tank, 10 PSI, 11" WC) pressure port system and tear away leak check adhesive sticker. MEGR-1232 Compact Series offers a compact integral two-stage regulator design perfect for lower BTU applications and confined spaces. They feature an adjustment range from 9-13" WC (factory 11" WC). Stainless steel integral components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms, and large precision machined aluminum orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. MEGR-1632 Series offers all of the same features as the compact MEGR-1232 series in a full size high capacity version. The full size MEGR-1632 diaphragm provides superior downstream regulation, has heavy duty wrench flats and a large 3/4" FNPT tapped drip lip vent to help prevent relief vent blockage. LP-MEGR-1232-BBF LP-MEGR-1232-HBF LP-MEGR-1232-HFF LP-MEGR-1632-BCF LP-MEGR-1632-CFF LP-MEGR-1632-HCF LP-MEGR-1632-JFF LP-MEGR-1232T-HBF LP-MEGR-1632T-HCF LP-MEGR-1632T-JFF REGULATOR-1ST & 2ND 1/4" FPT X 1/2" FPT 450K BTU 11" WC REGULATOR-1ST & 2ND FML POL X 1/2" FPT 450K BTU 11" WC REGULATOR-COMPACT HIGH CAP TWIN STAGE F/POL X 3/4" FNPT REGULATOR-1ST & 2ND 1/4" FPT X 1/2" FPT 850K BTU 11" WC REGULATOR-2ND 1/4" FPT X 3/4" NPT 11" WC REGULATOR-1ST & 2ND 1/4" FML POL X 1/2" FPT 850K BTU 11" WC REGULATOR-1ST & 2ND FML POL X 3/4" FPT 850,000 BTU 11 "WC REGULATOR-1ST & 2ND FML POL X 1/2"FPT 450K BTU 11" WC TEE IN REGULATOR-TWIN F.POL X 1/2" FNPT 11" WC OUTLET TEE INLET REGULATOR-TWIN F.POL X 3/4"FPT 11" WC OUTLET TEE INLET 18

19 Regulators Marshall Excelsior Integral 2 PSI MEC Excela-Flo integral two-stage regulators combine the first and second stage regulator setup into one convenient unit converting tank pressure to 2 psi. All MEC integral two-stage 2 psi regulators are white indicating 2 psi outlet pressure. They are recommended for installations with short piping distances, but provide the same advantages of two stage regulation with a single unit. 2 psi service regulators are used in conjunction with a line regulator either at the indoor appliance or a remote manifold distribution header inlet. All MEC integral two-stage regulator vent have tapped ports (7/ First Stage / 3/8" FNPT or 3/4" FNPT - Second Stage) and our exclusive E- Z Grip screens located over the outlet. Both the MEGR-1232E and MEGR-1632E series offer optimal relief performance that well exceeds UL test requirements providing over pressure protection of no more than 4 psi downstream pressure. MEC Excela-Flo integral two-stage domestic regulators feature a 25 year recommended replacement life, our exclusive Tri-Tap (tank, 10 psi, 2 psi) pressure port system and tear away leak check adhesive sticker. MEGR-1232E Compact Series offers a compact integral two stage 2 psi regulator design perfect for lower BTU applications and confined spaces. They feature an adjustment range from psi (factory set at 2 psi). Stainless steel integral components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms, and large precision machined aluminum orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. MEGR-1632E Full Size Series offers all of the same features as the compact MEGR-1232E series in a full size high capacity version. The full size MEGR-1632E diaphragm provides superior downstream regulation, has heavy duty wrench flats and a large 3/4" FNPT tapped drip lip vent to help prevent relief vent blockage. LP-MEGR-1232E-BBH LP-MEGR-1232E-HBH LP-MEGR-1632E-BCH LP-MEGR-1632E-CFH LP-MEGR-1632E-HCH LP-MEGR-1632E-JFH REGULATOR-COMPACT TWIN 1/4" FNPT INLET X 1/2"FNPT OUTLET REGULATOR-COMPACT TWIN FML POL INLET X 1/2" FPT OUTLET 2PSI REGULATOR-TWIN 1/4" FNPT X 1/2 " FNPT 2PSI REGULATOR-TWIN 1/4" FNPT X 3/4 " FNPT 2PSI REGULATOR-TWIN F.POL X 1/2" FNPT 2PSI REGULATOR-TWIN F.POL X 3/4" FNPT 2PSI 19

20 Regulators Marshall Excelsior High Pressure Industrial The MEGR-6120 Series are UL listed high-pressure regulators that meet a variety of applications for liquid or vapor service. The compact body design makes these regulators particularly useful in installations with space limitations. The basic MEGR-6120 Series regulators come equipped with a handwheel adjustment. The non-adjustable ME6121 Series provides a tamper-resistant spring case and one of seven fixed set points: 5, 10, 20, 30, 40, 50, or 60 PSI. The MEGR-164 Series adjustable high-pressure regulators offer a wide selection of available pressure ranges. High pressure regulators are typically used to reduce tank pressure to an intermediate pressure for use by another regulator. They may be used as high pressure regulators on distribution systems when used in conjunction with first stage downstream regulators. LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR-164/33 LP-MEGR-164/35 LP-MEGR-164/36 LP-MEGR-164/222 LP-MEGR-164-6/33 LP-MEGR-164-6/35 LP-MEGR-164-6/36 LP-MEGR-164-6/222 LP-MEGR-164SR/21 LP-MEGR-164SR/22 LP-MEGR-164SR/23 REGULATOR-1ST HIGH PRESSURE ADJ 1-30 PSI 1/4" FNPT IN/OUT REGULATOR-1ST HIGH PRESSURE ADJ 1-60 PSI 1/4" FPT IN/OUT REGULATOR-1ST HIGH PRESSURE ADJ PSI 1/4" FNPT IN/OUT REGULATOR-1ST HIGH PRESSURE FIXED 5 PSI 1/4" FPT IN/OUT REGULATOR-HIGH PRESSURE 10# FIXED 1/4" IN/OUT REGULATOR-1ST HIGH PRESSURE FIXED 20 PSI 1/4" FPT IN/OUT REGULATOR-FIXED HIGH PRESSURE 30 PSI 1/4" FNPT INLET/OUTLET REGULATOR-FIXED HIGH PRESSURE 40 PSI 1/4" FNPT INLET/OUTLET REGULATOR-1ST HIGH PRESSURE FIXED 50 PSI 1/4" FPT IN/OUT REGULATOR-1ST HIGH PRESSURE FIXED 60 PSI 1/4" FPT IN/OUT REGULATOR-1/2" FNPT 0-30 PSI ADJ W/TEE 10 PSI SET PT REGULATOR-1/2" FNPT 0-30 PSI ADJ W/TEE 20 PSI SET PT REGULATOR-1/2" FNPT 0-60 PSI ADJ W/TEE REGULATOR-1/2" FNPT PSI ADJ W/TEE 50 PSI SET PT REGULATOR-3/4" FNPT 0-30 PSI ADJ W/TEE 10 PSI SET PT REGULATOR-3/4" FNPT 0-30 PSI ADJ W/TEE 20PSI SET PT REGULATOR-3/4" FNPT 0-60 PSI ADJ W/TEE 40 PSI SET PT REGULATOR-3/4" FNPT PSI ADJ W/TEE 50 PSI SET PT REGULATOR-HP 1/2" FPT 0-15 PSI W/RELIEF & WRENCH ADJ 10PSI SP REGULATOR-HP 1/2" FPT 0-30 PSI W/RELIEF & WRENCH ADJ 15PSI SP REGULATOR-HP 1/2" FPT 0-30 PSI W/RELIEF & WRENCH ADJ 20PSI SP 20

21 NOTES 21

22 Regulators Marshall Excelsior Low Pressure Commercial The MEGR-S1202/MEGR-CS1200 series commercial/industrial regulators are large capacity, low pressure second stage units for installation at schools, bakeries, and similar applications. They contain a limited capacity internal relief valve and can be used in conjunction with either MEGR-1627 Series or MEGR-1630 Series high-pressure regulators. For high capacity installations, the MEGR- 1289H Series relief valve is required to be installed in the downstream system. The MEGR-1133 series pressure regulator is a manual, direct acting, self-operating, spring loaded, adjustable regulator. It is used in applications where pressure reduction is required. The regulator will reduce the risk of shock from abrupt changes of downstream conditions. This can help prevent safety equipment from shutting an operation down. The MEGR is equipped with external pressure registration; an external control line is needed to connect the output pressure port with the diaphragm chamber. The MEGR-1133 utilizes a balance diaphragm to reduce the effects of supply pressure changes on the output pressure. The external pressure registration of the standard MEGR-1133 also allows it to be used as a monitor regulator. LP-MEGR-CS1200IR6EC1 LP-MEGR-CS1200IR6EC3 LP-MEGR-CS1200IR6EC6 LP-MEGR-CS1200IR7EC1 LP-MEGR-CS1200IR7EC3 LP-MEGR-S1202G-BNC LP-MEGR-S1202G-CNC LP-MEGR-S1202H-CNK LP-MEGR-1133L-4 LP-MEGR-1133L-6 REGULATOR-IND 2ND 3/4" FPT 1/2" ORIFICE 10-14"WC REGULATOR-IND 2ND 1" FPT 1/2" ORIFICE REGULATOR-IND 2ND 1-1/4" FPT 1/2" ORIFICE WC REGULATOR-IND 2ND 3/4" FPT 5/16" ORIFICE 6-14" WC REGULATOR-IND 2ND 1" FPT 5/16" ORIFICE 6-14"WC REGULATOR-2ND 1-1/2" FPT 1" ORIFICE 9-18" WC REGULATOR-2ND 2" FPT 1"ORIFICE 9-18" WC REGULATOR-2ND 2" FPT PSI 1" ORIFICE REGULATOR-COMMERCIAL 2" FPT " WC SET PT. 14"WC REGULATOR-COMMERCIAL 2" FPT.75-2PSIG SET PT. 2PSI 22

23 Regulators Marshall Excelsior High Pressure Commercial The MEGR-1627 Series commercial/industrial regulator is a large capacity, high pressure unit for use in conjunction with MEGR-CS1200 or MEGR-S1202 Series regulators. It can also be used on final-stage (PSI to PSI) service. The diaphragm case and/or regulator body on the MEGR-1627 Series can be rotated in any of four positions to allow installation in locations with limited space. Available with a monitor or integral relief valve. The MEGR-1627 Series is perfectly suited for jurisdictional systems, grain dryers, direct fi red vaporizers or other high capacity service applications. The MEGR-1630 Series First Stage/Industrial regulators are large capacity, high pressure units for use in conjunction with MEGR-S1202 Series regulators. They can also be used on final stage (pounds-to-pounds) service. These regulators are best suited for industrial applications where high flow capacity is required. The MEGR-1133 series pressure regulator is a manual, direct acting, self-operating, spring loaded, adjustable regulator. It is used in applications where pressure reduction is required. The regulator will reduce the risk of shock from abrupt changes of downstream conditions. This can help prevent safety equipment from shutting an operation down. The MEGR is equipped with external pressure registration; an external control line is needed to connect the output pressure port with the diaphragm chamber. The MEGR-1133 utilizes a balance diaphragm to reduce the effects of supply pressure changes on the output pressure. The external pressure registration of the standard MEGR-1133 also allows it to be used as a monitor regulator. The MEGR-199 Series Industrial regulators are large capacity, pilot operated, low or high pressure units for use in applications with loads demanding up to 75,000,000 BTU/H capacity. These regulators are best suited for industrial applications where high flow capacity and a downstream monitor control line can be applied. The MEGR-199 series provides exceptional downstream control while operating at very high capacities with minimal droop under varying flow and inlet pressures. LP-MEGR-1627/5810 LP-MEGR-1627/6210 LP-MEGR-1627/7710 LP-MEGR-1627M/471 LP-MEGR-1627M/267 LP-MEGR-1627/576 LP-MEGR /78 LP-MEGR-1133H-2 LP-MEGR-1133H-3 LP-MEGR P LP-MEGR P LP-MEGR P LP-MEGR PH LP-MEGR PH REGULATOR-1ST 3/4" FPT 5-20 PSI 3/8" ORIFICE REGULATOR-1ST 3/4" FPT 5-20 PSI 1/2" ORIFICE REGULATOR-1ST 1" FPT 5-20 PSI 1/2" ORIFICE REGULATOR-1ST 1" FPT 5-20 PSI 1/2" ORIFICE W/MONITOR REGULATOR-1ST 2" FPT 5-20 PSI 1/2" ORIFICE W/MONITOR REGULATOR-1ST 2" FPT 5-20 PSI 1/2" ORIFICE REGULATOR-IND 1ST STAGE 2" FPT 1/2" ORIFICE 8-20 PSI OUTLET REGULATOR-2ND STAGE 2" FPT 2-5 PSI REGULATOR-2ND STAGE 2" FPT 5-10PSIG SET PT. 5PSI REGULATOR-2" FNPT PILOT OPER 7/8" ORIFICE 5-15PSI SET POINT REGULATOR-2" FNPT PILOT OPER 7/8" ORIFICE 10-20PSI SET POIN REGULATOR-2" FNPT PILOT OPER 1-1/8" ORIFICE 2-10PSI SP REGULATOR-2" FNPT PILOT OPER 1-1/8" ORIFICE 2-10 PSI SP REGULATOR-2" FNPT PILOT OPER 1-1/8" ORIFICE 10-20PSI SP 23

24 Regulators Marshall Excelsior Compact Regulators The MEGR-230 single-stage regulators are approved for use in small portable applications and outdoor cooking appliances utilizing low pressure. The MEGR-1912 series with capacity ratings of less than 320,000 BTU/hr (129 scfh), are often used on small portable outdoor appliances. The MEC MEGR-291 two-stage regulators are approved for use in nearly all portable applications and outdoor cooking appliances utilizing low pressure. They feature all zinc body construction, high and low 1/8 NPT pressure tap ports, an integral second stage drip lip vent and optional standard or 90 degree vent locations. The MEGR-130 series fixed high pressure single stage regulators are designed to provide an economical solution for pounds to pounds service applications. The MEGR-130 can be used to regulate air as well as LP gas. Regulators must be installed in compliance with federal, state or local codes or laws in accordance with NFPA 58. MEGR-350 single stage, adjustable high pressure regulator. The body and bonnet of both the fixed and adjustable regulators are precisely machined and feature a crimped design and fabric reinforced rubber diaphragm creating a positive seal for leak-free performance. LP-MEGR-230 LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR-231 LP-MEGR LP-MEGR-1912/109 LP-MEGR-1912/197 LP-MEGR-291 LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR LP-MEGR-350 LP-MEGR LP-MEGR REGULATOR-SINGLE STAGE 1/4" FNPT X 3/8" FPNT 140,000 BTU REGULATOR-SINGLE STAGE 3/8" FNPT X POL 9GPM REGULATOR-SINGLE STAGE 1/4" FNPT X 3/8" FNPT 90 DEG VENT REGULATOR-SINGLE STAGE QCC X 3/8" FNPT 90 DEG VENT REGULATOR-SINGLE STAGE BLACK F QCC X 3/8" FNPT REGULATOR-SINGLE HN POL 7/8" HX X 3/8" FNPT 90DEG VENT REGULATOR-SINGLE 1/4" FPT X 3/8" FPT REGULATOR-LOW PRESSURE 1/4" FNPT X 3/8" FNPT 5-10 WC RANGE REGULATOR-LOW PRESSURE 1/4" FNPT X 3/8" FNPT 12-24" WC REGULATOR-1ST & 2ND 1/4" FNPT IN X 3/8" FNPT OUT REGULATOR-COMPACT HI PRESSURE FIXED 5 PSI 1/4" FNPT IN/OUT REGULATOR-COMPACT HI PRESSURE FIXED 10 PSI 1/4" FNPT IN/OUT REGULATOR-COMPACT HI PRESSURE FIXED 15 PSI 1/4" FNPT IN/OUT REGULATOR-COMPACT HI PRESSURE FIXED 20 PSI 1/4" FNPT IN/OUT REGULATOR-COMPACT HI PRESSURE FIXED 30 PSI 1/4" FNPT IN/OUT REGULATOR-1ST HIGH PRESSURE 1-10 PSI 1/4" FNPT IN/OUT REGULATOR-1ST HIGH PRESSURE ADJ 1-20 PSI 1/4" FNPT IN/OUT REGULATOR-1ST HIGH PRESSURE ADJ 1-30 PSI 1/4" FNPT IN/OUT 24

25 Regulators Marshall Excelsior Automatic Changeover The MEGR-253 Series Automatic Changeover regulators automatically redirect LP gas vapor flow from an empty service cylinder to a reserve cylinder, without interruption of service. It features an easy to read green indicator which changes to red when the service cylinder needs to be refilled. These Two Stage Automatic Changeover regulators combine the first and second stage regulator into one unit converting full tank pressure to 11 WC. MEC Excela-Flo Automatic Changeover regulators prevent gas outages by switching supply cylinders over to the reserve cylinder automatically when the primary cylinder is near empty. When the primary cylinder is depleted causing the changeover to occur a red indicator will appear signifying the reserve cylinder in now in use and the primary cylinder can be refilled without loss of service. LP-MEGR-253 LP-MEGR-175CS61222-BAF LP-MEGR175CS61622BCF LP-MEGR175CS61622EBC REGULATOR-TWO STAGE AUTO CHANGE 1/4" INV FLR X 3/8" FPT REGULATOR-AUTO CHANGEOVER 1/4" IF IN X 1/2" FPT OUT 11" WC REGULATOR-CHANGEOVER AUTO 1/4" IF INLET X 1/2" FNPT OUT REGULATOR-AUTO CHANGEOVER 1/4" IF X 1/2" FPT 2 PSI 25

26 Regulators Maxitrol These regulators feature and aluminum housing. The 325 series features a high leverage valve linkage assembly to deliver positive dead end lock up. The regulators are capable of precise control from full flow down to pilot flow. L series are CSA certified. 325 Series Lever Acting Design 325 pounds to inches regulators with maximum inlet of 10 psi and multiple outlet pressures. 325L Series Lever Acting Design is for a maximum of 2 psi piping systems and 7-11" w.c. only. 12A39 and 12A49 are optional automatic vent limiting devices ball check permits unobstructed inhalation for fast regulator diaphragm response on opening cycle, but limits gas escapement to within ANSI standards should a diaphragm rupture. CSA certified for 2 psi (LP) and 5 psi (natural) inlet pressure. Use 12A39 with and 325-5L regulators; OPD21OD, brass construction, 3/8" NPT. Use 12A49 with 325-7A, 325-7AL, and 325-9L regulators; OPD210E, brass construction, 1/2" NPT. NOTE: When using the vent limiting device, regulator must be mounted in a horizontal upright position. LP REGULATOR-INDUSTRIAL 3/8" 4-12" SPRING MAX INLET 10 PSI LP REGULATOR-INDUSTRIAL 1/2" 4-12" SPRING MAX INLET 10 PSI LP REGULATOR-INDUSTRIAL 1/2" 4-12" SPRING MAX INLET 10 PSI LP REGULATOR-INDUSTRIAL 3/4" 4-12" SPRING MAX INLET 10 PSI LP REGULATOR-INDUSTRIAL 1" 4-12" SPRING MAX INLET 10 PSI LP-325-3L-33 REGULATOR-RESIDENTIAL 3/8" 7-11" SPRING MAX INLET 2 PSI LP-325-5L-44 REGULATOR-RESIDENTIAL 1/2" 7-11" SPRING MAX INLET 2 PSI LP-325-5L-88 REGULATOR-RESIDENTIAL 1" 7-11" SPRING MAX INLET 2 PSI LP-325-7AL-1010 REGULATOR-RES 1-1/4" 7-11" SPRING MAX INLET 2 PSI LP-325-7AL-1212 REGULATOR-GAS 2# 1-1/2" NPT 1,225,000 BTU LP-12A39 LIMITER-VENT FOR 325-5A APPLICATIONS LP-12A49 LIMITER-VENT FOR & LP-MAXICAP-5 COVER-REGULATOR MAXITROL 26

27 Regulator Accessories Pigtails - Copper These pigtail and hogtail assemblies come with two brass connectors brazed onto a heavy wall annealed copper tube with 250 psig pressure rating. The ¼" and 3/8" tube have a pull test rating of 500 and 750 pounds respectively. UL listed and tested in accordance with UL 569. LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME1669-6B90 LP-ME LP-ME LP-ME B270R LP-ME LP-ME LP-ME LP-ME LP-ME1680-5B90 LP-ME1680L-12 LP-ME1680L-20 LP-ME1680L-30 LP-ME LP-ME1684L-12 LP-ME LP-ME1689L-12 LP-ME1689-5B90 PIGTAIL-POL X POL 1/4" TUBE X 20" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 36" LENGTH LONG NIPPLE PIGTAIL-POL X INV FLR 1/4" TUBE 20" LENGTH LONG NIPPLE PIGTAIL-POL X INV FLR 1/4" TUBE 36" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 20" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 30" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 36" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 48" LENGTH LONG NIPPLE PIGTAIL-POL X INV FLR 1/4" TUBE 20" LENGTH LONG NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 3-1/4" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 12" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 1/4" TUBE X 20" LENGTH SHORT NIPPLE PIGTAIL-POL X INV FLR 1/4" TUBE 20" LENGTH SHORT NIPPLE PIGTAIL-POL X INV FLR 1/4" TUBE 36" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 6" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 12" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 18" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 20" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 36" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 1/4" TUBE X 6" LENGTH 90 DEG SHORT PIGTAIL-POL X POL 3/8" TUBE X 6" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 12" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 12" LENGTH BENT 270 DEG RIGHT PIGTAIL-POL X POL 3/8" TUBE X 20" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 30" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 36" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 48" LENGTH SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 5" LENGTH 90 DEG SHORT NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 12" LENGTH LONG NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 20" LENGTH LONG NIPPLE PIGTAIL-POL X POL 3/8" TUBE X 30" LENGTH LONG NIPPLE PIGTAIL-POL X 1/2"MPT 3/8" TUBE X 12" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/2"MPT 3/8" TUBE X 12" LENGTH LONG NIPPLE PIGTAIL-POL X 1/4" MPT 3/8" TUBE X 12" LENGTH SHORT NIPPLE PIGTAIL-POL X 1/4" MPT 3/8" TUBE X 12" LENGTH LONG NIPPLE PIGTAIL-POL X 1/4"MPT 3/8" TUBE X 5" LENGTH 90 DEG SHORT 27

28 Regulator Accessories Pigtails - Rubber UL and CGA (Canadian) listed rubber pigtails can be made in any length required. Minimum quantity required for special sizes is 100. Special orders are non-cancelable and non-returnable. To order special sizes, change last two numbers to required length in inches. i.e , U.L. Pigtail cannot exceed 60". UL and CGA listed rubber pigtails with QCC type 1 appliance connector. UL Listed Rubber Pigtails - High pressure hose 350 W.P burst with heated annealed brass fittings. LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 12" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 15" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 20" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 24" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 36" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 48" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 15" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 20" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 24" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 30" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 36" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 48" LENGTH LP PIGTAIL-RUBBER POL X 1/4" INV FLR 60" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" MPT TUBE 15" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" MPT TUBE 20" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" MPT TUBE 24" LENGTH LP PIGTAIL-RUBBER EX FLO POL X 1/4" MPT TUBE 30" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 12" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 15" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 18" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 20" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 24" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 30" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 36" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" INV FLR 1/4" TUBE X 60" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" MPT 1/4" TUBE X 15" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" MPT 1/4" TUBE X 24" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" MPT 1/4" TUBE X 36" LENGTH LP-MER PIGTAIL-RUBBER FQCC X 1/4" MPT 1/4" TUBE X 60" LENGTH 28

29 Regulator Accessories Pigtails - Rubber UL Listed LP UL LP UL LP-MER UL LP-MER UL LP-MER UL LP-MER UL LP-MER UL LP-MER UL PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 20" LENGTH UL PIGTAIL-RUBBER EX FLO POL X 1/4" INV FLR 36" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" INV FLR X 12" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" INV FLR X 15" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" INV FLR X 18" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" INV FLR X 20" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" INV FLR X 30" LENGTH UL PIGTAIL-RUBBER FQCC X 1/4" MPT X 15" LENGTH UL Pressure Gauges and Accessories Bottom Mount 2" Brass Stem Dry To determine the correct gauge, environment along with normal operating system pressure must be considered. The pressure range of the gauge should be twice the normal system pressure to maximize gauge life and accuracy. Feature bottom mount design with brass stem. LP-MEJ500 LP-MEJ501 LP-MEJ502 LP-MEJ SG302 SG602 SG1002 SG1602 SG2002 SG3002 GAUGE-1/4" MPT BRASS BTM MT 2" STEEL DIAL DRY 0-15 PSI GAUGE-1/4" MPT BRASS BTM MT 2" STEEL DIAL DRY 0-30 PSI GAUGE-1/4" MPT BRASS BTM MT 2" STEEL DIAL DRY 0-60 PSI GAUGE-1/4" MPT BRASS BTM MT 2" STEEL DIAL PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY 0-30 PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY 0-60 PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY PSI GAUGE-1/4" MPT BRASS BTM MT 2" DRY PSI 29

30 Regulator Accessories Pressure Gauges and Accessories Back Mount 2" Brass Stem Dry To determine the correct gauge, environment along with normal operating system pressure must be considered. The pressure range of the gauge should be twice the normal system pressure to maximize gauge life and accuracy. Feature back mount design with brass stem. LP-MEJ510 LP-MEJ511 LP-MEJ512 LP-MEJ516 SG602C SG1002C SG2002C GAUGE-1/4" MPT BRASS BACK MT 2" STEEL DIAL DRY 0-15 PSI GAUGE-1/4" MPT BRASS BACK MT 2" STEEL DIAL DRY 0-30 PSI GAUGE-1/4" MPT BRASS BACK MT 2" STEEL DIAL DRY 0-60 PSI GAUGE-1/4" MPT BRASS BACK MT 2" STEEL DIAL DRY PSI GAUGE-1/4" MPT BRASS BCK MT 2" DRY 0-60 PSI GAUGE-1/4" MPT BRASS BCK MT 2" DRY PSI GAUGE-1/4" MPT BRASS BCK MT 2" DRY PSI Bottom Mount 2-1/2" Brass Stem Stainless Case Liquid These gauges are designed for use with any medium not corrosive to brass or bronze. Liquid filled gauges are recommended for reducing shock caused by pressure fluctuations or vibration. Features bottom mount brass 1/4" MNPT stem and 304 stainless steel case. GG30 GG60 GG100 GG160 GG200 GG300 GG400 GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ 0-30 PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ 0-60 PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BTM MT 2-1/2" LIQ PSI Back Mount 2-1/2" Brass Stem Stainless Case Liquid These gauges are designed for use with any medium not corrosive to brass or bronze. Liquid filled gauges are recommended for reducing shock caused by pressure fluctuations or vibration. Features back mount brass ¼" MNPT stem and 304 stainless steel case. WGG60C WGG100C WGG160C WGG200C WGG300C WGG400C GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ 0-60 PSI GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ PSI GAUGE-1/4" MPT BRASS BCK MT 2-1/2" LIQ PSI 30

31 Regulator Accessories Pressure Gauges and Accessories Bottom Mount 2-1/2" Stainless Stem Dry To determine the correct gauge, environment along with normal operating system pressure must be considered. The pressure range of the gauge should be twice the normal system pressure to maximize gauge life and accuracy. Features stainless steel case, bottom mount design and stainless steel stem. LP-J542 GAUGE-1/4" MPT SS BTM MT 2" STEEL DIAL PSI Bottom Mount 2-1/2" Stainless Stem Liquid To determine the correct gauge, environment along with normal operating system pressure must be considered. The pressure range of the gauge should be twice the normal system pressure to maximize gauge life and accuracy. Features stainless steel case, bottom mount design and stainless steel stem. WGGSS60 WGGSS100 WGGSS160 WGGSS400 LP-MEJ542 GAUGE-1/4" MPT SS BTM MT 2-1/2" LIQ 0-60 PSI GAUGE-1/4" MPT SS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT SS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT SS BTM MT 2-1/2" LIQ PSI GAUGE-1/4" MPT SS BTM MT 2-1/2" SS DIAL LIQ PSI Back Mount 2-1/2" Stainless Stem Liquid These gauges are designed for use with any medium not corrosive to stainless steel. Liquid filled gauges are recommended for reducing shock caused by pressure fluctuations or vibration. Features back mount stainless steel ¼" MNPT stem and 304 stainless steel case. WGGSS400C GAUGE-1/4" MPT SS BCK MT 2-1/2" LIQ PSI Bottom Mount 4" Brass Stem Dry 4" gauge with ¼" brass bottom mount stem, improved visibility for remote installations. SG604 SG1004 GAUGE-1/4" MPT BRASS BTM MT 4" DRY 0-60 PSI GAUGE-1/4" MPT BRASS BTM MT 4" DRY PSI Bottom Mount 4" Brass Stem Stainless Case Liquid 4" liquid filled gauge with stainless steel case, ¼" brass bottom mount stem, improved visibility for remote installations. GG60-4 GG1004 GAUGE-1/4" MPT BRASS BTM MT 4" LIQ 0-60 PSI GAUGE-1/4" MPT BRASS BTM MT 4" LIQ PSI 31

32 Regulator Accessories Pressure Gauges and Accessories Gauge Reducer Coupling LP-MF1814B COUPLER-REDUCING 1/4" FPT X 1/8" MPT BRASS Gauge Dampeners B301AB LP-1449 DAMPENER-GAUGE 1/4" FPT X 1/4" MPT STEEL ADAPTER-GAUGE 1/4" FPT X 1/4" MPT STEEL Vent Extension FLEX-Vent - The MEC Flex-Vent provides a safe and easy solution to vent LP gas regulators away from openings, sources of ignition or other potential fire hazards. Meets all requirements of the new flexible material allowance in the 2011 NFPA-58, section (3). Durable hose constructed of flexible PVC material suitable for use with LP gas vapor. UV stable for maximum resistance to outdoor exposure. 3/4" NPT swivel inlet for easy installation. Standard 90 vent assembly with screen. Mounting clamps and coated masonry screws supplied. Crimped ends for maximum durability. LP-ME LP-ME LP-ME LP-ME KIT-FLEX VENT 36" X 34" MNPT FIXED ENDS KIT-FLEX VENT 48" X 3/4" MNPT FIXED ENDS KIT-FLEX VENT 72" X 3/4" MNPT FIXED ENDS KIT-FLEX VENT 120" X 3/4" MNPT NOT CRIMPED Miscellaneous Brackets LP-P100A LP-P100L LP-MEGR-900 BRACKET-MTG R966&R600SERIES BRACKET-REGULATOR UNIVERSAL FITS-FISHER/SHERWOOD/REGO BRACKET-REGULATOR UNIVERSAL Z FOR MEGR-253,291,298,

33 Regulator Accessories Miscellaneous Vent Assemblies Vent Assemblies - Attached directly to the regulator vent connection or to a regulator vent line, vent assemblies should be pointed downward on outdoor installations to avoid moisture buildup in the regulator spring case. Units with a stabilizer assembly are intended for regulators with stability problems. The stabilizer gives a restricted breathing rate under normal conditions, opening for rapid discharge when necessary. LP-Y602-1 LP-Y LP-ME900-6 LP-Y VENT ASSY-UMBRELLA 1/4" MNPT VENT ASSY-ANGLE 1/4" FPT VENT ASSY- ANGLE 3/4" FPT VENT ASSY-ANGLE 1" FPT Covers LP-RC-1P LP-MEGR-862 Tees and Tee Blocks COVER-PLASTIC REGULATOR COVER-REGULATOR UNIVERSAL 2ND STAGE FOR MEGR-253,291,298,300 LP-ME1704B TEE-BLOCK-W/OUT CHECK FPOL X 3 LP-ME1702B TEE-BLOCK W/OUT CHECK 1-1/8 HEX NUT LP-ME1702A TEE-BLOCK W/CHECK 1-1/8 HEX NUT LP-ME1705A TEE-BLOCK W/CHECK FPOL X 1/4" MPT LP-MEP456A TEE-1/4"MANUAL CHANGEOVER LP-ME1700A TEE-BLOCK W/CHECK 1/4"INV FLAR X 1/4"MPT 33

34 Domestic Float Gauges Brass Head Threaded HA Series The HA series gauges are only for top mount applications in an above ground tank. These come standard with a 1" threaded brass head with a 2" hex wrenching flat and mount in a 1" tank coupling. Note: Torque head evenly to 75 to 150 ft. lbs. TA Series The TA series gauges are only for top mount applications in an above ground tank. These come standard with a 1 1/4" threaded brass head with a 2" hex wrenching flat and mount in a 1 ¼" tank coupling. Note: Torque head evenly to 100 to 200 ft. lbs. LP-HA130A LP-HA160A LP-HA194A LP-HA210A LP-TA130A LP-TA160A LP-TA194A LP-TA210A GAUGE-FLOAT JR LP 24" DIA 1" MPT GAUGE-FLOAT JR LP 30" DIA 1" MPT GAUGE-FLOAT JR LP 37" DIA 1" MPT GAUGE-FLOAT JR LP 41" DIA 1" MPT GAUGE-FLOAT JR LP 24" DIA 1-1/4" MPT GAUGE-FLOAT JR LP 30" DIA 1-1/4" MPT GAUGE-FLOAT JR LP 37" DIA 1-1/4" MPT GAUGE-FLOAT JR LP 41" DIA 1-1/4" MPT 34

35 Domestic Float Gauges Junior Junior Gauges These gauges are available in top, side or end, and angle mounting for above ground tanks. They are supplied standard with a Buna-N gasket and four zinc-plated steel mounting screws (1/4"-28 x 7/8"). These gauges mount in a Junior flanged coupling with a 2 1/32" diameter bolt circle. Note: Torque mounting bolts evenly to 20 to 50 in./lbs. LP-JA124I GAUGE-FLOAT JR LP 24" DIA 4-BOLT LP-JA154I GAUGE-FLOAT JR LP 30" DIA 4-BOLT LP-JA192J GAUGE-FLOAT JR LP 37" DIA 4-BOLT LP-JA206I GAUGE-FLOAT JR LP 41" DIA 4-BOLT LP-JD100F GAUGE-FLOAT JR LP 30" DIA END MOUNT Senior Senior Gauges These gauges are available in top, side or end, and angle mounting for above ground tanks. A Visible 4 dial is available. They are supplied standard with a Buna-N gasket and four zincplated steel mounting screws (5/16"-24 x 7/8"). These gauges mount in a Senior flanged coupling with a 2 1/2" diameter bolt circle. Note: Torque mounting bolts evenly to 30 to 60 in./lbs. LP-SA130A GAUGE-FLOAT SR HEAD LP 24" DIA TOP MOUNT LP-SA160A GAUGE-FLOAT SR HEAD LP 30" DIA TOP MOUNT LP-SA194A GAUGE-FLOAT SR HEAD LP 37" DIA TOP MOUNT LP-SA214A GAUGE-FLOAT SR HEAD LP 41" DIA TOP MOUNT LP-SC160A GAUGE-FLOAT SR LP 30" DIA 45 DEG ANGLE MOUNT LP-SC194D GAUGE-FLOAT SR LP 37" DIA 45DEG ANGLE MOUNT LP-SC214C GAUGE-FLOAT SR LP 41" DIA 45 DEG ANGLE MOUNT LP-SD080D GAUGE-FLOAT SR LP 24" DIA SIDE OR END MOUNT LP-SD100C GAUGE-FLOAT SR LP 30" DIA SIDE OR END MOUNT LP-SD120G GAUGE-FLOAT SR LP 37" DIA SIDE OR END MOUNT LP-SD140A GAUGE-FLOAT SR LP 41" DIA SIDE OR END MOUNT 35

36 Domestic Float Gauges Junior Motor Fuel Visible Junior Motor Fuel Visible These gauges are available in top, side or end, and angle mounting for motor fuel tanks. They are supplied standard with a Buna-N gasket and four zinc-plated steel mounting screws (1/4"-28 x 7/8"). These gauges mount in a Junior flanged coupling with a 2 1/32" diameter bolt circle. Note: Torque mounting bolts evenly to 20 to 50 in./lbs. LP-20AC LP-22AC LP-18CC LP-24CC GAUGE-FLOAT MOTOR FUEL JR 20" DIA 45 DEG UPPER MOUNT GAUGE-FLOAT MOTOR FUEL JR 22" DIA 45 DEG UPPER MOUNT GAUGE-FLOAT MOTOR FUEL JR 18" DIA CENTER SIDE MOUNT GAUGE-FLOAT MOTOR FUEL JR 24" DIA SIDE MOUNT Universal for Lift Truck Cylinders Universal for Lift Truck Cylinders These gauges are for 20 lb., 33 lb., and 43 lb. lift truck cylinders. The JU, TU and UU series are universal and will read either vertically or horizontally. The JD060A is for horizontal cylinders only. These gauges mount in a Junior flanged, a ¾" flanged or a 1 ¼" tank coupling. LP-JD060A LP-UU160B LP-TU160B LP-JU160B LP-UU212A LP-TU212A LP-JU212A GAUGE-FLOAT CYL 20, 33, 44 LB HORIZONTAL 4 BOLT MOUNT GAUGE-FLOAT CYL 33 LB 3/4" MPT UNIVERSAL GAUGE-FLOAT CYL 33 LB 1-1/4" MPT UNIVERSAL GAUGE-FLOAT CYL 33 LB UNIVERSAL 4 BOLT MOUNT GAUGE-FLOAT CYL 43 LB 3/4" MPT UNIVERSAL GAUGE-FLOAT CYL 43 LB 1-1/4" MPT UNIVERSAL GAUGE-FLOAT CYL 43 LB UNIVERSAL 4 BOLT MOUNT 36

37 Domestic Float Gauges Replacement Dials LP-5003S00039 DIAL-CHAMBER JR REMOTE READY LP-5001S00001 DIAL-CHAMBER SR REMOTE READY LP DIAL-REPLACEMENT JUNIOR WITHOUT REMOTE READY PLUGS LP DIAL-REPLACEMENT SENIOR WITHOUT REMOTE READY PLUGS LP-5343S01791 DIAL-UNIVERSAL HOR-VERT #33 FORKLIFT LP-5378S01888 DIAL-FACE HORIZONTAL FORKLIFT 5323S01789 LP-2701-CV DIAL-ASSY 5 % LP DIAL-LP 2701 W/ PIN AT 95% LP-3180S17001 DIAL-KIT UNIVERSAL SR SQUIBB LP-3181S17039 DIAL-JR VISIBLE 2"GLUE ON NEW SQUIBB LP-G12858 DIAL-SNAP ON FOR G & 34 LB LIFT TRUCK CYLINDER 37

38 Domestic Float Gauges Accessories O-Rings and Gaskets LP LP-15-4 LP-15-7 O-RING-JR GAUGE GASKET-SR GAUGE GASKET-JR GAUGE Screw Kits and Screws The Gauge Doctor complete and easy to use kit to drill out and repair broken gauge bolts in your domestic tanks. Kit Includes: One drill guide block that accommodates both junior and senior gauges. Bolts for securing the block to the gauge flange on the tank. Drill bits for drilling out the broken bolts. Taps to rethread the bolt holes. Complete 50 piece starter kit containing new gauge bolts and gaskets for both junior and senior gauges Junior bolts are 1/4" Senior bolts are 5/16"-24 LP-GAUGE DOCTOR KIT-GAUGE SCREW REPAIR LP SCREW-JR GAUGE HEAD 1/4" X 28 LP SCREW-SR GAUGE HEAD 5/16" X

39 NOTES 39

40 Valves Relief External Relief Valves - Used on ASME and DOT containers, all working parts of these valves are outside the container connection so they must be protected against mechanical damage. The external relief valves use brass as material of construction. Standard product temperature rating is -20 to 160 F. Protective caps are shipped with Fisher external relief valves. Replacement caps may be ordered separately. Diaphragm Relief Valves - Type 289H relief valve is designed for installation downstream of a larger high pressure regulator or low pressure regulators in most all relief applications. The larger diaphragm in this relief valve provides extremely sensitive operation, with a temperature rating of -20 to 150 F. Type MEVS-PVE431/250 UL listed relief valve is designed for use with storage containers as a primary pressure relieve valve on ASME above and below ground installations. All working components are external to the container connection away from possible product contaminants. Compatible with all standard propane pressure vessels with NPT couplings. Type 1805 relief valve is designed for installation between the first and second stage regulators or in the downstream line from a high pressure regulator used for final stage service where high line pressures are allowed. Available in 1" or 2" valve bodies with a temperature rating of -20 to 150 F (-29 to 66 C). Economy Hydrostatic Relief Valves are designed to protect piping and shutoff valves from over pressure situations where liquid LP gas or NH3 has the potential to be trapped. They provide pressure relief at or in excess of the stated pressure setting, protecting against line or plumbing system failures. FEATURES: 1/4" MNPT inlet to fit any domestic valve port or service port. 440 psig start-to-discharge. Non-adjustable, tamper resistant design. Protective vinyl cap included. Internal Pressure Relief Valves for ASME and DOT Containers are designed specifically for use as a primary pressure relief device on ASME containers up to 2000 gallon water capacity, furnished with rain cap for protection against contamination. Cross Reference: : Sherwood-UV443AM / Rego-8684G : Sherwood-UV433AM / Rego-7583G : Sherwood-UV453AM / Rego-8685G : Sherwood-UV443AC / Rego-8684GC : Sherwood-UV445AM / Rego-8544G Type MEV125/250 aluminum valve is UL listed and designed for use with large LP and NH3 storage containers as a primary pressure relieve valve on ASME above and below ground bulk plant installations. All working components are external to the container connection away from possible product contaminants. Compatible with 1-1/4" FNPT multiple head units. 40

41 Valves Relief LP-H VALVE-EXTERNAL RELIEF 1/4" MPT 250 PSI LP-H VALVE-EXTERNAL RELIEF 1/4" MPT 312 PSI LP-H123 VALVE-EXTERNAL RELIEF 1/4" MPT 375 PSI LP-H124 VALVE-EXTERNAL RELIEF 1/4" MPT 450 PSI LP-H VALVE-EXTERNAL RELIEF 1/2" MPT 312 PSI LP-H148 VALVE-EXTERNAL RELIEF 1/2" MPT 375 PSI LP-H144 VALVE-EXTERNAL RELIEF 1/2" MPT 450 PSI LP-H VALVE-EXTERNAL RELIEF 3/4" MPT 250 PSI LP-H VALVE-EXTERNAL RELIEF 3/4"MPT 275 PSI LP-H VALVE-EXTERNAL RELIEF 3/4" MPT 312 PSI LP-H173 VALVE-EXTERNAL RELIEF 3/4" MPT 375 PSI LP-H174 VALVE-EXTERNAL RELIEF 3/4" MPT 450 PSI LP-98H-30 VALVE-RELIEF 1" FPT PSI LP P VALVE-RELIEF 1" FPT PSI LP P VALVE-RELIEF 2" FPT 5-20 PSI LP-289H-2 VALVE-RELIEF 2" FNPT CI 1/2-2-1/4 PSI LP-289H-43 VALVE-RELIEF 1" FNPT AI PSI LP-289H-49 VALVE-RELIEF 1" FNPT AI PSI LP-MEVS-PVE431B/250 VALVE-EXT RELIEF 3/4" MPT 250 PSI BRASS W/CAP LP-MEVS-PVE431/250 VALVE-EXT RELIEF 1" MPT 250 PSI BRASS W/CAP LP-MEH225 VALVE-RELIEF 1/4" MPT 440 PSI HYDROSTATIC BRASS NITRILE LP-MEH225/400 VALVE-RELIEF 1/4" MPT 400 PSI HYDROSTATIC BRASS LP-MEH225SS VALVE-RELIEF 1/4" MPT 440 PSI HYDROSTATIC SS LP-MEVS-UVE443AM/250 VALVE-RELIEF 1" MPT 250 PSI LP-MEVS-UVE433AM/250 VALVE-3/4" MPT INTERNAL RELIEF 250# LP-MEVS-UVE453AM/250 VALVE-RELIEF 1-1/4" NPT 250 PSI STD LP-MEVS-UVE445AM/250 VALVE-RELIEF 1" MPT 250 PSI MOTOR FUEL LP-MEV75FIR VALVE-INTERNAL RELIEF 3/4" MPT X 1-1/16" 375 PSI DOT FRKLIFT LP VALVE-INTERNAL RELIEF 3/4" MPT X 1-1/16" 375 PSI DOT FRKLIFT LP-MEV VALVE-EXT RELIEF 1-1/4" MNPT 250 PSI LP-MEP174 ADAPTER-PIPE AWAY 1/2" FPT X X 1" 20 UNEF 41

42 Valves Relief Relief Accessories Replacement Relief Valve Rain Caps - are made of rubber and used to keep moisture and foreign materials from entering the valves. These units are mounted on the outside of the protective hood on the tank. Universal Relief Valve Cover Type MEH501 is made of durable, fade resistant vinyl. Type MEH502 and 503 covers are intended to protect both internal and external relief valves ranging in size from 1/2" to 1-1/4" NPT from moisture or other possible contaminants. Using the universal shower cap style relief valve covers will allow technicians to carry two sizes that will protect the majority of domestic tank relief valves. They are made with durable UV stable yellow vinyl material. LP-P174 ADAPTER-PIPE AWAY 1/2" NPT H135 & H173 LP-MEP ADAPTER-PIPE AWAY 45 DEG FORKLIFT ALUMINUM LP-MEP175C CAP-PROTECTIVE W/LANYARD FOR MEV75FIR LP-MEP175P CAP-PROTECTIVE "H" REL VALVE LP-P206 CAP-RAIN FOR H360/H369 LP-P145 CAP-PROTECTIVE 1-3/4" MPT H185/H275/1805 LP-MEPS A CAP-3/4" RELIEF VALVE LP-MEPS A CAP-1" RELIEF VALVE LP-MEPS A CAP-1-1/4" RELIEF VALVE LP-MEH CAP-YELLOW 1.5 ID X 1" W/BLK LOGO LP-MEH502 COVER-RELIEF VALVE 1/2" TO 3/4" YELLOW VINYL LP-MEH503 COVER-RELIEF VALVE 3/4" TO 1-1/4" LP-MEP200FIR TOOL-INSTALLATION 2" FULL INT RELIEF VALVE 1-1/2" HEX 42

43 Valves Relief Relief Accessories NOTES 43

44 Liquid Withdrawal Liquid Withdrawal Valves are designed to provide a safe means by which to transfer liquid from a tank during an emergency or container relocation. These valves can be equipped with an integral excess flow device for direct product transfer or without when used in conjunction with liquid withdrawal adapters. Liquid Withdrawal Adapters are designed for use between the liquid transfer shutoff valve and the liquid withdrawal tank valve. These adapters enable the tank valve to open properly and allow a tight seal when transferring liquid. Special threads on the tank valve and the adapter help eliminate tampering. A1597R valves consist of a service valve and an excess flow valve. The built-in tri-guard internal relief valve bleeds product back to the tank when hose pressure exceeds tank pressure by 50 psig. In this way, hose life is extended, chance of hose rupture is reduced and personnel are protected. The ME449 incorporates a double O-ring seal on the stem assembly for leak free operation even under extreme temperature fluctuations. The stem also has a back seat feature and a swivel seat disc to further enhance the durability of this valve. The double lead thread design of the stem allows adjustment from the closed position to full open in 6 full turns. The outlet boss on the side of the valve is tapped ¼" FNPT and plugged for your convenience. For direct installation into pressure vessel, use ME449X/19.5 with built-in 19.5 gpm excess flow shut off protection. ME673DEX-6SP is a UL Listed high capacity combination double check fill and liquid bypass return line shut off valve. These valves are equipped with an integrated excess flow feature that is internal to the tank protecting against tank separation. The preinstalled side mounted ME601-6 double check fill valve allows for safe low emissions container filling at a convenient right angle orientation. The top mount 3/4" FNPT port above integrated shut off valve seat allows for maximum liquid bypass return flow rates without adding an external shut off valve. MESPVE3250CLM intended for use in liquid withdrawal service for DOT containers up to 100 lb. capacity as fuel line shutoff valves in combination with a fill and vapor relief valve. Features one-piece forged brass body construction with integral 375 psi relief valve and heavy duty replaceable zinc hand wheel. Male CGA555 liquid outlet with shutoff and integral 1.0 gpm excess flow valve. A1598P VALVE-WITHDRAWAL 1-1/4" MPT X 1" FPT NH3 45GPM A1597R VALVE-WITHDRAWAL 1-1/4" MPT X 1" FPT W/INT RELIEF NH3 45GPM LP-ME450 VALVE-LIQUID LOADING/UNLOADING 3/4"FNPT X 1 3/4" F ACME LP-ME460 VALVE-LIQUID WITHDRAWL 3/4" MPT X 5/8" FPT 21 GPM W/EX FLO LP-ME462 VALVE-TANK LIQUID WITHDRAWAL 1-1/4" MPT BRASS W/CAP 36GPM LP-ME449 VALVE-WITHDRAWL 3/4" MPT X 3/4" FPT LP-ME449X/19.5 VALVE-LIQUID WITHDRAWAL 3/4" MPT X 3/4" FPT 195 GPM BRASS LP-ME453 ADAPTER-3/4" FPT X 3/4" MPT CHECK LOCK ME453 LP-ME458 ADAPTER-3/4" FPT X 1-5/8" UNF CHECK LOCK ME458 LP-ME GASKET-FOR ME458 LP-ME O-RING-ID.799 THICK.003 LP-ME672D VALVE-ANGLE MULTI PURPOSE NH3 1-1/4" MNPT X 1" FNPT 78 GPM LP-ME673DEX-6SP 44 VALVE-RETURN 1-1/4" CHECK FILL/BYPASS 58 GPM

45 Valves Liquid Withdrawal LP-MESPVE3250CLM11.6 VALVE-LIQUID SERVICE 100# DOT 3/4" NGT X MLCGA PSI Fill and Vapor Return Double Check Fill Valves ME601 series are designed for DOT forklift, engine fuel and ASME residential tanks, these double check filler valves automatically open with pump pressure providing maximum product flow rates. The ME601 series feature a resilient bonded main valve seal, integral break away feature leaves primary check intact in the even in the event of delivery truck roll away, field repairable upper check seat and factory applied thread sealant. The ME663 vapor equalizing valve features both an upper and lower check assembly. The upper check can be opened with vapor equalizing hose couplings equipped with projecting nozzle tips where the lower check is a normally open excess flow type. It features high flow construction, resilient bonded main valve seal, integral break away that leaves the primary check intact in the event of a line pull away and a field repairable upper check seat. Type D140 filler valves are used on ASME tanks found at bulk plants, as well as tanks used on bobtail and transport trucks. The heavy duty construction allows for safe and rapid filling. A two piece design with both an upper and lower back check. A metal to metal lower back check protects against loss of product in case of an accident and permits removal of the upper body with the tank under pressure. Leakage from the upper and lower body connection is prevented by a resilient gasket that is retained within a specially machined groove in the lower body. Internal parts are of stress relieved brass bar stock with the exception of stainless steel springs and stems. The ME602-8 is UL listed and designed for remote filling applications where a standard tank type filler valve is not practical. Perfectly suited for motor fuel applications or other hard to reach tank applications. This single check fill valve is designed to provide maximum product fill rates along with an automatic shutoff once flow ceases. LP-ME601-6 LP-ME LP-ME663 LP-D140 LP-ME602-8 VALVE-FILLER DOUBLE CHECK 3/4" MPT X 1-3/4" ML ACME VALVE-FILLER DOUBLE CHECK 1-1/4" MPT X 1-3/4" ML ACME VALVE-RETURN DOUBLE CHECK 3/4" MPT X 1-1/4" ML ACME VALVE-FILLER 2"MPT X 2-1/4"ML ACME VALVE-CHECK FILL 1-3/4" MLACME X 1/2" ML FLARE W/CAP & LANYD 45

46 Valves Combo The MES-PVE2098AT UL listed multi-service valves are designed for use on domestic ASME underground tanks that require a single opening except for a separate opening for liquid withdrawal. Constructed of ductile iron with epoxy coating, featuring durable O-ring service valve packing. ME662 and ME665 UL listed valves are intended to use in vapor withdrawal service for ASME containers or as fuel line shutoff valves in combination with an integral double check fill and vapor equalization valve. They do not incorporate an internal pressure relief valve and are intended for use in containers that have a stand-alone pressure relief valve sized to properly handle the container s capacity. They feature a one piece forged brass body, dual O-ring packing design with bonnet assembly, heavy duty replaceable zinc hand wheel. The ME662 has a ¼" FNPT plugged test port and the ME665 has a 1/8" FNPT plodded test port. MES-PVE2030 Series UL listed valves are intended for use in vapor withdrawal service for DOT containers up to 200 lb. capacity as fuel line shutoff valves in combination with a fill and vapor relief valve. Ideal for on-site filling without interruption of service by combining all functions into a single 3/4" NPT tank opening. MES-PVE2035 Series for DOT or ASME containers ranging from 420 lbs. to 100 gallon. LP-MES-PVE2098AT LP-MES-PVE2098PT LP-MES-PVE2030BC11.6 LP-ME662 LP-ME665 LP-MESPVE2030BCSC11 LP-MES-PVE2035AT11.7 LP-MESPVE2035ATSC11 LP-MESPVE2035ATSC250 VALVE-CLUSTER UG TANK 2-1/ 2" FPT 250 PSI W/30" DIPTUBE VALVE-CLUSTER UG TANK 2-1/2" FPT 250 PSI W/30" DIPTUBE VALVE-CLUSTER # DOT 3/4"NGT W/FILL 375PSI 11.6 DIP VALVE-MULTI SERVICE 1-1/2" MPT ASME VALVE-VAPOR MULTI-SERVICE 3/4" MPT X FML POL W/12" DIPTUBE VALVE-CLUSTER MULTISERVICE 3/4" NGT W/FILL 375 PSI RELIEF VALVE-MULTI 1" INLET 375 PSI VALVE-CLUSTER MULTI-SERVICE 1" NGT W/FILL 375 PSI RELIEF VALVE-CLUSTER 420# ASME 1" NGT W/FILL 250PSI RELIEF 11.7" DIP 46

47 Valves 80% Bleed Low Emission Fixed Liquid Level Gauges are designed to provide a way to visually determine that a tank has reached maximum allowable fill capacity. The dip tube end of a fixed liquid level gauge should be set equal to 80% of the liquid level tank capacity and installed in the vapor space of the tank. The vent valve should be opened before filling begins during which time vapor will be discharged. Once the tank reaches maximum liquid fill capacity (80% of tank capacity), liquid will begin to discharge from the vent valve telling the operator the tank has reached maximum allowable fill capacity and the filling operation should cease immediately and MEJ410 are UL listed and reduce emissions to the atmosphere, supplied with an orifice hole and are available with or without liquid level dip tube. They have a removable stem for convenient cleaning and stem seal replacement and are durable all brass construction Cross Reference Sherwood (PV10A), Marshall Excelsior (MEJ400), Rego (3165), J Cross Reference Sherwood (PV10B), Rego (3165S12.0) LP LP-MEJ LP-MEJ LP-MEJ400C LP-MEJ410C-120 REFER TO LP-MEJ400 VALVE-WITHDRAWL 1/4" MPT GAUGE-FIXED LIQUID LEVEL 1/4" MPT 12" TUBE GAUGE-LIQUID LEVEL W/DIP TUBE LOW EMISSIONS BRASS GAUGE-LIQUID LEVEL 1/4"MPT #54 ORIFICE NO DIP TUBE BRASS GAUGE-LIQUID LEVEL 1/4"MPT #54 ORIFICE 12" DIP TUBE BRASS 47

48 Valves Cylinder The ME9101 series is intended for vapor or liquid withdrawal service on DOT forklift or engine fuel containers. Each of these valves incorporates an excess flow valve at the tanks inlet end to prevent excessive product loss in the event of a downstream fuel line failure. The ME9101 series feature one piece forged brass body construction with a dual O-ring packing design. They are easy to repair and replace the universal bonnet assembly. They also have factory applied thread sealant and a replaceable, heavy duty zinc hand wheel. MESPVE3250CLG11.6 UL Listed for use in vapor withdrawal service for DOT containers up to 100 lb. capacity as a fuel line shut off valve in combination with a liquid fill and vapor relief valve. ME9101D-11.7 UL listed vapor withdrawal valve is intended for service in ASME and DOT containers or as fuel shutoff valves. Does not incorporate in integral pressure relief valve and is intended for use in containers that have a separate standalone pressure relief valve sized to properly handle the container capacity. One piece forged brass body with dual O-ring. Easily repairable with a universal bonnet assembly, high flow rate, factory applied thread sealant and heavy duty replaceable zinc hand wheel. The is a heavy duty POL service valve for DOT containers with a pressure relief valve. PV3250BC-312 is a UL listed replacement valve for small ASME engine fuel tanks with 20 square feet or less in surface area that are now obsolete. It features a flow rate of 705 CFM air and a 1 3/4" Acme thread filler connection. The UL listed is designed for vapor or liquid withdrawal service on DOT fork lift truck containers and ASME containers. It is equipped with an excess flow limiter. It does not have an integrated pressure relief valve and must only be used as an accessory valve on containers that have an independent pressure relief valve suitable for the container s capacity. The features a double O-ring stem seal, tamperproof design, sturdy brass hand wheel, static seat disc and recessed excess flow valve. LP-ME9101C1 LP-ME9101C5 LP-MESPVE3250CLG11.6 LP-ME9101H6 LP-ME9101P5H LP-ME9101D-11.7 LP LP LP-PV3250BC-312 LP VALVE-3/4" X POL NO RELIEF SERVICE / VAPOR VALVE-SERVICE 100# 3/4" MPT X FML POL 2.6 GPM EX FLO VALVE-SERVICE 3/4" MPT X FPOL 100LB CYL 11.6" DT 375PSIG VALVE-WITHDRAWL 3/4" MPT X 3/8" ML FLARE 90DEG MOTOR FUEL VALVE-WITHDRAWL 3/4" MPT X 3/8" NPT 18 DOT FORKLIFT VALVE-3/4" MPT X POL NO RELIEF W/11.7 DIPTUBE & BLEEDER VALVE-WITHDRAWL 3/4" MPT X 3/8" NPT VALVE-SERVICE 3/4" MPT X FML POL 10.6" DIP TUBE VALVE-VAOR SERVICE 3/4" MPT X FML POL 312 PSI DOT CYL VALVE-WITHDRAWL 3/4" MPT X 3/8" SAE 70DEG ASME MOTR FUEL 48

49 Valves Cylinder OPD DOT Cylinder Valves for vapor withdrawal up to 40 lb. capacity. These UL listed, Type 1 Acme valves have a vapor service outlet, relief valve, captive fixed liquid level gauge and an overfill prevention device (OPD). They feature rapid purging and filling with over one million BTU withdrawal capacities, steel safety cage surrounding critical welds provides long term operational protection, and tri-lobular one piece forged brass hand wheel. A double O-ring stem seal provides for improved leak resistance and Ever Seal sealant is pre-applied. The quality O-ring check valve seat, opens only with positive seal, and upward spray filling eliminates premature shutoffs. Gauge Ready Stopfill Valve Replacement and shows actual liquid level, not pressure. It is affordable, accurate and allows for fast fill and evacuation. The gauge is easy to read from top, end or the side. Green indicates OK time to grill, red indicates Low time to fill. Dial is sold separately. You must order one OPD valve and one dial for complete unit. LP-PV0404 LP-PV1104 LP-PV2004G LP-PV3004S LP-PV4004S LP-PV3004A LP-PV4004A LP LP LP VALVE-OPD CYL 5LB - 11LB 3.0 DIP TUBE VALVE-OPD CYL 10 LB 3.6 DIP TUBE VALVE-OPD CYL 20 LB 4.0 DIP TUBE VALVE-OPD CYL 30 LB 4.7 DIP TUBE VALVE-OPD CYL 40 LB 6.4 DIP TUBE VALVE-OPD CYL 30 LB ALUM 5.8 DIP TUBE VALVE-OPD CYL 40 LB ALUM 7.0 DIP TUBE VALVE-20# OPD- DIAL SEPERATE VALVE-30# OPD -DIAL SEPERATE DIAL-CLIP ON 49

50 Valves Valve Locks CX-1708 PADLOCK-MASTER 1-3/4" X 15/16" KEYED ALIKE KEY #2685 CX-A473 PADLOCK-MASTER 1-3/4" X 15/16" KEYED DIFFERENTLY FE550 COVER-VALVE LOCK UP TO 2" COVER-VALVE LOCK 3" LP-LC-1-CAP CAP-LOCKING FILLER VALVE LP-ME KEY-POL LOCKSEAL LP-ME530 LOCK-POL BULK 12PK W/1KEY LP-ME530PL KIT-PADLOCKING SN POL LOCK W/PLUGS & KEY PACK OF 12 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Brass Female ACME Couplings Marshall Excelsior These UL listed couplings are used as connections between the hose and transfer valve. The filler coupling is designed to provide different connections for the end of a hose inlet or an angle, globe or quick acting valve on the outlet when transferring liquid. These filler couplings come with a factory installed retaining ring that limits the travel of the handle or nut during disconnect reducing spin offs and promoting proper venting of the captured product. LP-ME100 LP-ME101 LP-ME110 LP-ME111 LP-ME112 LP-ME120WR LP-ME130WR LP-ME442 COUPLING-FILLER 1-1/4" FML ACME X 3/8" MPT BRASS COUPLING-FILLER 1-1/4" FML ACME X 1/2" MPT BRASS COUPLING-FILLER 1-3/4" FML ACME X 1/2" MPT BRASS COUPLING-FILLER 1-3/4" FML ACME X 3/4" MPT BRASS COUPLING-FILLER 1-3/4" FML ACME X 1" MPT BRASS COUPLING-FILLER 2-1/4" FML ACME X 1-1/4" MPT BRASS COUPLING-FILLER 3-1/4" FML ACME X 2" MPT BRASS NUT COUPLING-FILLER 3-1/4" FML ACME X 1-1/4" FPT BRASS 50

51 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Steel Female ACME Couplings Marshall Excelsior These UL listed couplings are used as connections between the hose and transfer valve. The filler coupling is designed to provide different connections for the end of a hose inlet or an angle, globe or quick acting valve on the outlet when transferring liquid. These filler couplings come with a factory installed retaining ring that limits the travel of the handle or nut during disconnect reducing spin offs and promoting proper venting of the captured product. LP-ME111S LP-ME112S LP-ME635-6 LP-ME635-8 LP-ME121SWR LP-ME130SWR LP-ME Squibb Taylor A1131F COUPLING-FILLER 1-3/4" FML ACME X 3/4" MPT STEEL COUPLING-FILLER 1-3/4" FML ACME X 1" MPT STEEL COUPLING-FILLER 1-3/4" FML ACME X 3/4" MPT SPEED STEEL COUPLING-FILLER 1-3/4" FML ACME X 1" MPT SPEED STEEL COUPLING-FILLER 2-1/4" FML ACME X 1-1/4" MPT STEEL COUPLING-FILLER 3-1/4" FML ACME X 2" MPT STEEL COUPLING-FILLER 4-1/4" FML ACME X 3" MNPT SS COUPLING-FILLER 1" MPT X 1-3/4 FML ACME SPEED STEEL Brass Male ACME x Female NPT Marshall Excelsior LP-ME192 LP-ME193 LP-ME210 LP-ME211 LP-ME212 LP-ME213 LP-ME214 LP-ME250 LP-ME LP-ME ADAPTER-1-1/4" ML ACME X 1/2" FPT BRASS ADAPTER-1-1/4" ML ACME X 3/4" FPT BRASS ADAPTER-1-3/4" ML ACME X 1/4" FPT BRASS ADAPTER-1-3/4" ML ACME X 3/8" FPT BRASS ADAPTER-1-3/4" ML ACME X 1/2" FPT BRASS ADAPTER-1-3/4" ML ACME X 3/4" FPT BRASS ADAPTER-1-3/4" ML ACME X 1" FPT BRASS ADAPTER-3-1/4" ML ACME X 1-1/4" FPT BRASS ADAPTER-3-1/4" ML ACME X 2" FPT BRASS ADAPTER-3-1/4" ML ACME X 3" FPT BRASS 51

52 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Steel Male ACME x Female NPT Marshall Excelsior LP-ME213S LP-ME214S LP-ME252S-16 LP-ME508S-24 ADAPTER-1-3/4" ML ACME X 3/4" FPT STEEL ADAPTER-1-3/4" ML ACME X 1" FPT STEEL ADAPTER-3-1/4" ML ACME X 2" FPT STEEL ADAPTER-3-1/4" ML ACME X 3" FPT STEEL Brass Male ACME x Male NPT Marshall Excelsior LP-ME498-4/2 LP-ME498-6/3 LP-ME215 LP-ME216 LP-ME217 LP-ME233 LP-ME502-12/8 LP-ME502-16/10 LP-ME502-16/12 LP-ME LP-ME503A-16 LP-ME262 LP-ME ADAPTER-1-1/4" ML ACME X 1/2" MNPT X 1/4" FPT BRASS ADAPTER-1-1/4" ML ACME X 3/4" MPT X 3/8" FPT BRASS ADAPTER-1-3/4" ML ACME X 3/4" MPT BRASS ADAPTER-1-3/4" ML ACME X 1" MPT BRASS ADAPTER-1-3/4" ML ACME X 1-1/4" MPT BRASS ADAPTER-2-1/4" ML ACME X 1-1/4" MPT BRASS ADAPTER-2-1/4" ML ACME X 1-1/2" MPT X 1" FPT BRASS ADAPTER-2-1/4" ML ACME X 2" MPT X 1-1/4" FPT BRASS ADAPTER-2-1/4" ML ACME X 2" MPT X 1-1/2" FPT BRASS ADAPTER-3-1/4" ML ACME X 2" MPT BRASS ADAPTER-3-1/4" ML ACME X 2" MPT W/SCREEN ADAPTER-3-1/4" ML ACME X 3" MPT BRASS ADAPTER-4-1/4" ML ACME X 3" MNPT BRASS 52

53 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Steel Male ACME x Male NPT Marshall Excelsior LP-ME520S-8 LP-ME521S-4 LP-ME215S LP-ME216S LP-ME233S LP-ME502S-16/10 LP-ME503S-16 LP-ME262S LP-ME Brass Male ACME x Male ACME Marshall Excelsior LP-ME270 LP-ME273 ADAPTER-1-1/4" ML ACME X 1" MPT STEEL ADAPTER-1-3/4" ML ACME X 1/2" MPT STEEL ADAPTER-1-3/4" ML ACME X 3/4" MPT STEEL ADAPTER-1-3/4" ML ACME X 1" MPT STEEL ADAPTER-2-1/4" ML ACME X 1-1/4" MPT STEEL ADAPTER-2-1/4" ML ACME X 2" MPT X 1-1/4" FPT STEEL ADAPTER-3-1/4" ML ACME X 2" MPT STEEL ADAPTER-3-1/4" ML ACME X 3" MPT STEEL ADAPTER-4-1/4" ML ACME X 3" MNPT STEEL ADAPTER-1-1/4" ML ACME X 1-1/4 ML ACME BRASS ADAPTER-1-3/4" ML ACME X 1-3/4" ML ACME BRASS Steel Male ACME x Male ACME Marshall Excelsior LP-ME273S LP-ME275S LP-ME277S ADAPTER-1-3/4" ML ACME X 1-3/4" ML ACME STEEL ADAPTER-2-1/4" ML ACME X 2-1/4" ML ACME STEEL ADAPTER-3-1/4" ML ACME X 3-1/4" ML ACME STEEL 53

54 ACME Adapters, Couplings, Caps, Gaskets and O-Rings 1-3/4" Fill Adapter and Gasket ME571 - Intended to be attached to the LP gas delivery truck hose outlet. Features minimal flow restriction for fast delivery and provides the ability to remove the hose end filler valve in the event that the tank fill valve fails to close. During a tank filler valve failure, the integral check valve prevents loss of product. The ME571 is specifically designed to work in conjunction with the ME800 series of minimal loss hose end valves and will allow normal swivel operation of the hose end valve fill nozzle. ME572 and ME574 adapter is intended to be attached to the LP gas delivery truck hose outlets. It has minimal flow restriction which allows for fast delivery and also gives the user the ability to remove the filler hose in the event that the fill valve fails to close. In the event of a filler valve failure the integral check valve prevents loss of product. ME574EXT - Intended for LP gas delivery truck hose outlets where the tank fill inlet is located below ground level. Incorporates the same minimal flow restriction feature as our original ME572 design with the addition of a 7" extension to the tank side of the adapter. Provides a safe alternative for filling underground tanks should the tank fill valve fail to close properly. In this event the user can simply decouple the hose end delivery valve from the adapter leaving the safety check valve installed preventing loss of product. Features: Integral break away feature in the event of roll away truck leaving check intact on tank. Overall length still allows adapter to fit inside protective tank collar. Available with or without safety release vent valve installed. Available with standard 1 3/4" F. Acme connection nut or with our extended easy grip 1 3/4" F. Acme handle. M570 - filler hose adapter is intended for the outlet of bobtail truck filling hose, the M570 enables the filling hose to be removed if the filler valve fails to close. An integral back check in the adapter prevents gas from escaping in the event of a failure of the filler valve. LP-ME571 LP-ME572 LP-ME574 LP-ME574EXT LP-M570 LP-T13098-T0012 LP-T13103-T0012 ADAPTER-HOSE END CHECK 1-3/4"FML ACME X 1-3/4"ML ACME ADAPTER-1-3/4" ML ACME X 1-3/4 FML ACME ADAPTER-FILLER HOSE SWIVEL 1-3/4"FML ACME X 1-3/4"ML ACME ADAPTER-EXT 1-3/4" FML ACME X 1-3/4" ML ACME SWVL CHK VENT ADAPTER-HOSE END CHECK 1-3/4" FML ACME X 1-3/4" ML ACME GASKET-BLACK WASHER 54

55 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Brass Couplings - Vapor Return LP-ME140 LP-ME141 LP-ME150 LP-ME151 LP-ME151C LP-ME160 COUPLER-RETURN 1-1/4" FML ACME X 3/8" MPT BRASS COUPLER-RETURN 1-1/4" FML ACME X 1/2" MPT BRASS COUPLER-RETURN 1-3/4" FML ACME X 3/4" MPT BRASS COUPLER-RETURN 1-3/4" FML ACME X 1" MPT BRASS COUPLER-RETURN 1-3/4" FML ACME WING NUT X 1" MPT COUPLER-RETURN 2-1/4" FML ACME X 1-1/4" MPT W/BRASS NUT Steel Couplings - Vapor Return LP-ME141S LP-ME150S LP-ME151S LP-ME151SC LP-ME646-8 COUPLER-RETURN 1-1/4" FML ACME X 1/2" MPT STEEL COUPLER-RETURN 1-3/4" FML ACME X 3/4" MPT STEEL COUPLER-RETURN 1-3/4" FML ACME X 1" MPT STEEL COUPLER-RETURN 1-3/4" FML ACME X 1" MPT STEEL WING NUT COUPLER-RETURN 1-3/4" FML ACME X 1" MPT STEEL Brass Adapter Caps Marshall Excelsior LP-ME611 LP-ME612 LP-ME614 LP-ME613 CAP-ADAPTER 2-1/4" FML ACME X 1-3/4" ML ACME BRASS CAP-ADAPTER 3-1/4" FML ACME X 1-3/4" ML ACME BRASS CAP-ADAPTER-2-1/4" ML ACME X 3-1/4 FML BRASS CAP-ADAPTER 4-1/4" FML ACME X 3-1/4" ML ACME BRASS 55

56 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Steel Adapter Caps Fisher LP-M623 CAP-ADAPTER 4-1/4" FML ACME X 3-1/4" ML Marshall Excelsior LP-ME612S LP-ME614S LP-ME623 CAP-ADAPTER 3-1/4" FML ACME X 1-3/4" ML ACME REDUC STEEL CAP-ADAPTER 3-1/4" FML ACME X 2-1/4" ML ACME STEEL CAP-ADAPTER 4-1/4" FML ACME X 3-1/4" ML ACME STEEL Squibb Taylor A582 ST-A2004S Plastic ACME Caps Marshall Excelsior CAP-ADAPTER 2-1/4" FML ACME X 1-3/4" ML ACME STEEL CAP-ADAPTER REDUCER NH3 2-1/4" ML X 1-3/4" FML ACME STEEL LP-ME108 LP-ME109 LP-ME106 CAP-1-1/4" FML ACME PLASTIC CAP-1-3/4" FML ACME PLASTIC CAP-3-1/4" FML ACME PLASTIC 56

57 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Brass ACME Caps Marshall Excelsior The flange allows for easy operation of pneumatic or proximity interlock switches which control the safety systems of transport vehicles. The stainless steel flange is flush mounted to the Acme cap. LP-ME229-1 LP-ME229F-1C LP-ME229F5-1C LP-ME431F LP-ME431F-1 LP-ME431F-1C LP-ME431R-1 LP-ME441F LP-ME441F-1 LP-ME441F-1C LP-ME441F8-1C LP-ME Steel ACME Caps Fisher CAP-1-3/4" FML ACME BRASS W/RING & CHAIN CAP-1-3/4" FML ACME BRASS WING NUT STYLE W/CABLE ASSY CAP-1-3/4" FML ACME BRASS W/5" SS FLG CAP-2-1/4" FML ACME BRASS CAP-2-1/4" FML ACME BRASS W/KNOB & CHAIN CAP-2-1/4" FML ACME W/CABLE ASSY CAP-2-1/4" ACME BRASS W/TAPPED HOLE CAP-3-1/4" FML ACME BRASS CAP-3-1/4" FML ACME BRASS W/KNOB & CHAIN CAP-3-1/4" FML ACME W/CABLE ASSY CAP-3-1/4" FML ACME BRASS W/CABLE & 8" FLG CAP-4-1/4" FML ACME W/RING & CABLE & KNOB PLUG BRASS Female ACME Caps - ACME caps of various sizes and materials are used on male ACME threads to keep debris out of the piping systems. Small sizes are designed for hand tightening. Standard product temperature rating is -20 to 160 F. / -29 to 71 C. LP-M CAP-4-1/4" ACME STEEL 57

58 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Steel ACME Caps Marshall Excelsior LP-ME229FS-1 LP-ME229FS-1C LP-ME229S-1 LP-ME431FS LP-ME431FS-1C LP-ME441FS LP-ME441FS-1C LP-ME441RS-1 LP-ME Plastic ACME Plugs Marshall Excelsior CAP-1-3/4" FML ACME STEEL W/CHAIN CAP-1-3/4" FML ACME STEEL W/CABLE CAP-1-3/4" ACME STEEL W/CHAIN CAP-2-1/4" FML ACME STEEL CAP-2-1/4" FML ACME STEEL W/CABLE CAP-3-1/4" FML ACME W/KNOB STEEL CAP-3-1/4" FML ACME STEEL W/CABLE CAP-3-1/4" ACME & TAPHOLE PLUG W/CHAIN STEEL CAP-4-1/4" FML ACME W/RING & CABLE & KNOB PLUB STEEL LP-ME178 LP-ME179 LP-ME171-1 LP-ME180 LP-ME180-1 LP-ME181 LP-ME181-1 PLUG-PLASTIC 1-1/4" ACME PLUG-1-3/4" ACME PLASTIC PLUG-PLASTIC 1-3/4" ML ACME W/ CHAIN PLUG-PLASTIC 2-1/4" ACME PLUG-PLASTIC 2-1/4" ACME W/CHAIN Y-PLASTIC SEAL PLUG-PLASTIC 3-1/4" ACME PLUG-PLASTIC 3-1/4" ML ACME W/CHAIN 58

59 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Aluminum ACME Plugs Marshall Excelsior LP-ME239 PLUG-1-3/4" ACME ALUMINUM Ring and Chain Assemblies LP-MEP147 LP-MEP148 LP-MEP167 LP-MEP183 CHAIN-RING CAPS/DUST SEAL 1-1/4" & 1-3/4" ACME CHAIN-RING CAPS/DUST SEAL 1-3/4" & 2-1/4" ACME CHAIN-HOOK 2-1/4" X 3-1/4" ACME CAPS CHAIN-RING CAP/DUST SEAT 3-1/4" ACME 59

60 Gaskets Acme Gaskets - Acme gaskets are made of Buna-N material and are designed for LP gas service. They are shown in actual size and fit acme thread end of valves, adapters, speed couplers, and quick couplers. NOTE: Picture is for illustration only, may not be actual size. 60

61 ACME Adapters, Couplings, Caps, Gaskets and O-Rings Gaskets SERVICEMAN S REPLACEMENT SEAL KIT WITH CARRYING CASE Features: Durable ABS plastic container with storage latch. Preformed insert with individual spaces for each gasket/o-ring size. Labeled with each gasket/o-ring size and part number for easy identification and reorder. All gaskets/o-rings manufactured from UL approved compounds for LP Gas and Anhydrous Ammonia service. Kit Includes: /4" Acme Flat Gaskets /4" Acme Flat Gaskets 9-1 1/4" Acme Forklift Flat Gaskets /4" Acme Flat Gaskets /4" Acme Flat Gaskets 12 - Male Forklift Connector O-Rings 12 - POL O-Rings LP-MEW3 LP-MEW2 LP-MEW5 LP-MEW6 LP-MEW7 LP-15-4 LP-15-7 LP-MEW4 LP-MEW1 GASKET-1-1/4" ACME GASKET-1-3/4" ACME GASKET-2-1/4" ACME GASKET-3-1/4" ACME GASKET-4-1/4" ACME GASKET-SR GAUGE GASKET-JR GAUGE GASKET-M220M FTG FORKLIFT KIT-GASKET 61

62 ACME Adapters, Couplings, Caps, Gaskets and O-Rings O-Rings LP-8122 LP-8124 LP-8126 LP-8128 LP-8130 LP LP-T LP LP-T12945-T0012 O-RING-1-1/4" ACME O-RING-1-3/4" ACME O-RING-2-1/4" ACME O-RING-3-1/4" ACME O-RING-4-1/4" ACME O-RING-JR GAUGE O-RING-FORKLIFT QUICK COUPLER O-RING-POL M390 & MR HEATER O-RING-POL 62

63 Tubing, Pipe, Hose and Accessories TracPipe Tubing and Accessories Standard TracPipe Tubing COUNTERSTRIKE TUBING - The capability of CounterStrike to withstand electrical energy has been tested by a leading U.S. lightning laboratory, Lightning Technologies Inc. The laboratory duplicated typical field damage attributed to lighting for CSST. The electrical energy level in coulombs (one ampere flowing for one second) that was known to cause damage to standard CSST was used as a baseline to determine the performance level of CounterStrike. When tested against standard CSST, CounterStrike was shown to be up to 400 times more resistant to the damaging effects of electrical energy than competitive CSST piping. CSA approved Compliant with codes in all 50 states Use with auto flare fittings No additional bonding requirements Cuts with standard tube cutter Ratings up to 125 psi LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS LP-FGP-CS AutoFlare Straight Fittings TUBING-COUNTERSTRIKE 3/8" 100' ROLL TUBING-COUNTERSTRIKE 3/8" 250' ROLL TUBING-COUNTERSTRIKE 1/2" 100' ROLL TUBING-COUNTERSTRIKE 1/2" 250' ROLL TUBING-COUNTERSTRIKE 1/2" 500' ROLL TUBING-COUNTERSTRIKE 3/4" 100' ROLL TUBING-COUNTERSTRIKE 3/4" 250' ROLL TUBING-COUNTERSTRIKE 1" 100' ROLL TUBING-COUNTERSTRIKE 1" 180' ROLL TUBING-COUNTERSTRIKE 1-1/4" 150' ROLL TUBING-COUNTERSTRIKE 1-1/2" 250' ROLL LP-FGP-FST-375N FITTING-AUTOFLARE STRAIGHT 3/8" LP-FGP-FST-500 FITTING-AUTOFLARE STRAIGHT 1/2" LP-FGP-RING-500 RING-SPLIT SPARE AUTOFLARE 1/2" PACK OF 10 LP-FGP-FST-750 FITTING-AUTOFLARE STRAIGHT 3/4" LP-FGP-RING-750 RING-SPLIT SPARE AUTOFLARE 3/4" PACK OF 10 LP-FGP-FST-1000 FITTING-AUTOFLARE 1" LP-FGP-SFST-375 FITTING-AUTOSNAP 3/8" STRAIGHT BRASS LP-FGP-SFST-500 FITTING-AUTOSNAP 1/2" STRAIGHT BRASS LP-FGP-SFST-750 FITTING-AUTOSNAP 3/4" STRAIGHT BRASS LP-FGP-SFST-1000 FITTING-AUTOSNAP 1" STRAIGHT BRASS 63

64 Tubing, Pipe, Hose and Accessories TracPipe Tubing and Accessories AutoFlare Flange Fittings LP-FGP-BFF-375 LP-FGP-BFF-500 LP-FGP-BFF-750 LP-FGP-BFF-1000 LP-FGP-BFF-1250 LP-FGP-ELLB-375 LP-FGP-ELLB-500 LP-FGP-BF90V-500 LP-FGP-BF90V-750 AutoFlare Brass Couplings FITTING-AUTOFLARE 3/8" W/BRASS FLG FITTING-AUTOFLARE 1/2" W/BRASS FLG FITTING-AUTOFLARE 3/4" W/BRASS FLG FITTING-AUTOFLARE 1" W/BRASS FLG FITTING-AUTOFLARE 1-1/4" W/BRASS FLG FITTING-AUTOFLARE 3/8" 90 DEG W/BRASS FLG FITTING-AUTOFLARE 1/2" 90 DEG W/BRASS FLG FITTING-AUTOFLARE VALVE 1/2" 90 DEG W/BRASS FLG FITTING-AUTOFLARE VALVE 3/4" 90 DEG W/BRASS FLG LP-FGP-CPLG-375 COUPLING-TRACKPIPE 3/8" LP-FGP-CPLG-500 COUPLING-TRACKPIPE 1/2" LP-FGP-CPLG-750 COUPLING-TRACKPIPE 3/4" LP-FGP-CPLG-1000 COUPLING-TRACKPIPE 1" AutoFlare Tees LP-FGP-TF500-T500 TEE-1/2" X 1/2" X 1/2" LP-FGP-TF750-T750 TEE-3/4" X 3/4" X 3/4" LP-FGP-TF1000-T1000 TEE-1" X 1" X 1" 64

65 Tubing, Pipe, Hose and Accessories TracPipe Tubing and Accessories AutoFlare Reducing Tees AutoFlare Tee x NPT LP-FGP-RT-752 TEE-REDUCING 3/4" X 1/2" X 1/2" LP-FGP-TF750-T500 TEE-REDUCING 3/4" X 3/4" X 1/2" LP-FGP-TF1000-T500 TEE-REDUCING 1" X 1" X 1/2" LP-FGP-TF1000-T750 TEE-REDUCING 1" X 1" X 3/4" LP-FGP-TF1250-T500 TEE-REDUCING 1-1/4" X 1-1/4" X 1/2" LP-FGP-T LP-FGP-T LP-FGP-T LP-FGP-T TEE-1/2" X 1/2" X 1/2" FNPT TEE-3/4" X 3/4" X 1/2" FNPT TEE-3/4" X 3/4" X 3/4" FNPT TEE-1" X 1" X 1" FNPT AutoFlare Stub-Outs and Termination LP-FGP-ASP-500 STUB OUT-APPLIANCE 1/2" X 2" LP-FGP-FPT-500 STUB OUT-FIREPLACE 1/2" X 6" LP-FGP-MT6-500 BRACKET-TERMINATION METER 1/2" X 6" LP-FGP-MT6-750 BRACKET-TERMINATION METER 3/4" X 6" LP-FGP-MT BRACKET-TERMINATION METER 1" X 6" LP-FGP-MT BRACKET-TERMINATION METER 1/2" X 12" LP-FGP-MT BRACKET-TERMINATION METER 3/4" X 12" 65

66 Tubing, Pipe, Hose and Accessories TracPipe Tubing and Accessories Distribution Manifolds and Wall Boxes LP-FGP-MI-PC MANIFOLD-COATED (1) 3/4" INLET X (5) 1/2" OUTLETS LP-FGP-MI-ST-500 MANIFOLD-STACKABLE 1/2" X 1/2" PORTS LP-FGP-MI-ST-750 MANIFOLD-STACKABLE 3/4" X 1/2" PORTS LP-FGP-MB2 BRACKET-MANIFOLD LP-FGP-WBTM-500 BOX-WALL 1/2" METAL W/VALVE 7 X 7 X 3 LP-FGP-WBTM-750 BOX-WALL 3/4" METAL W/VALVE 7 X 7 X 3 AutoFlare Brackets Striker Plates LP-FGP-MT-BRAC BRACKET-TERMINATION LP-FGP-SP-025 PLATE-STRIKER QUARTER 3" X 2" LP-FGP-SP-050 PLATE-STRIKER HALF 3" X 7" LP-FGP-SP-075 PLATE-STRIKER THREE QUARTER 3" X 9" LP-FGP-SP-100 PLATE-STRIKER FULL 3" X 12" LP-FGP-SP-617 PLATE-STRIKER LARGE 6-1/2" X 17" 66

67 Tubing, Pipe, Hose and Accessories TracPipe Tubing and Accessories Metal Conduit and Tube Cutter LP-FGP-FPY CONDUIT-3/4" FLOPPY FITS 3/8" 50 FT COIL LP-FGP-FPY CONDUIT-1" FLOPPY FITS 1/2" 50 FT COIL LP-FGP-FPY CONDUIT-1-1/4" FLOPPY FITS 3/4" 25 FT COIL LP-FGP-FPY CONDUIT-1-1/2" FLOPPY FITS 1" 25 FT COIL LP-FGP-TC-15 CUTTER-3/8" - 1" Brass Bonding Clamps Brass Bonding Clamps have been tested and approved by CSA in accordance with UL 467/CSA C22.2 No when installed on black iron, galvanized steel pipe and the TracPipe AutoFlare hex fitting. LP-FGP-GC-1 CLAMP-BONDING 3/8", 1/2" X 1/2", 3/4", 1" IRON PIPE LP-FGP-GC-2 CLAMP-BONDING 3/4", 1", 1-1/4" X 1-1/4", 1-1/2", 2" IRON PIPE 67

68 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories CTS and IPS Polyethylene Tubing Polyethylene Mechanically Joined LP Gas Distribution Products - For many years, copper tubing and heat fused polyethylene piping represented the preferred connecting systems for LP gas installation. The 1992 edition of NFPA 58 now permits the use of mechanical joining methods for polyethylene piping systems. These revisions make NFPA 58 consistent with the natural gas codes which have permitted mechanical joining of polyethylene gas piping for many years. Our complete system complies with NFPA 58 - Perfection offers you a complete, mechanically joined polyethylene LP gas distribution system that complies with NFPA 58. In addition, our complete line meets or exceeds the applicable requirements of ASTM D-2513, U.S. DOT Part 192, CSA B137.4 and IAPMO. Polyethylene piping systems are revolutionizing the LP gas industry because of their ease of installation and superior resistance to corrosion. Polyethylene (PE) piping systems should be considered for use in stationary domestic and commercial vapor applications of 30 lbs. or less. Under DOT and NFPA 58 regulations all persons installing PE piping shall be trained under the applicable joining procedure. This training shall be documented. FEI salesmen are qualified in training whether it is mechanical or fusion application. For further information see paragraphs 2-4.2(f), 2-4.3(d), Section 2-4.4, and A-2-4.4(c)(3) of 1992 NFPA Pamphlet 58. Part Number Nominal Size Pipe SDR Nominal OD Minimum Wall Thickness Nominal ID Approximate Weight Coil Length Coil OD Coil ID Coil Width LP-CTS-SDR7 1/2" 7.625".090".445" 6.5 lbs./100' 500' 34" 26" 6.5" LP-CTS1 1" ".099".927" 13.8 lbs./100' 500' 45" 30" 10" LP-IPS12 1/2" ".090" 9.0 lbs./100' 500' 44" 30" 10.5" LP-IPS34 3/4" ".095".860" 12.4 lbs./100' 500' 44" 30" 10.5" LP-IPS1 1" ".120" 1.075" 19.4 lbs./100' 500' 44" 30" 10.5" LP-IPS /4" ".166" 1.328" 34.0 lbs./100' 500' 72" 48" 7.5" LP-IPS2 2" ".216" 1.943" 63.0 lbs./100' 500' 76" 54" 8" LP-IPS3 3" ".307" lbs./100' 20' or 40' (500' coils available) LP-IPS4 4" ".395" lbs./100' 20' or 40' LP-CTS-SDR7 LP-CTS1 LP-IPS12 LP-IPS34 LP-IPS1 LP-IPS125 LP-IPS2 LP-IPS3 LP-IPS4 TUBING-CTS POLY 1/2" 500' ROLL TUBING-CTS POLY 1" 500' ROLL TUBING-IPS POLY 1/2" 500' ROLL TUBING-IPS POLY 3/4" 500' ROLL TUBING-IPS POLY 1" 500' ROLL TUBING-IPS POLY 1-1/4" 500' ROLL TUBING-IPS POLY 2" 500' ROLL TUBING-IPS POLY 3" 40FT STICK TUBING-IPS POLY 4" 40' STICK 68

69 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Permasert Couplings - Mechanical LP LP LP LP LP LP LP COUPLING-MECHANICAL 1/2" CTS PERMASERT COUPLING-MECHANICAL 1/2" IPS PERMASERT COUPLING-MECHANICAL 3/4" IPS PERMASERT COUPLING-MECHANICAL 1" CTS PERMASERT COUPLING-MECHANICAL 1" IPS PERMASERT COUPLING-MECHANICAL 1-1/4"IPS PERMASERT COUPLING-MECHANICAL 2" IPS PERMASERT Permasert Couplings - Repair LP LP LP LP LP LP LP Permasert Couplings - Reducing LP LP LP LP LP LP LP LP LP LP COUPLING-REPAIR 1/2" CTS COUPLING-REPAIR 1/2" IPS COUPLING-REPAIR 3/4" IPS COUPLING-REPAIR 1" CTS COUPLING-REPAIR 1" IPS COUPLING-REPAIR 1-1/4" IPS COUPLING-REPAIR 2" IPS COUPLING-REDUCING PERMASERT 1/2" CTS X 1" CTS COUPLING-REDUCING PERMASERT 1/2" CTS X 1" IPS COUPLING-REDUCING PERMASERT 1/2" CTS X 3/4" IPS COUPLING-REDUCING PERMASERT 1/2" IPS X 1/2" CTS COUPLING-REDUCING PERMASERT 1/2" IPS X 3/4" IPS COUPLING-REDUCING PERMASERT 1" CTS X 3/4" IPS COUPLING-REDUCING PERMASERT 1" IPS X 3/4" IPS COUPLING-REDUCING PERMASERT 1-1/4" IPS X 3/4" IPS COUPLING-REDUCING PERMASERT 1-1/4" IPS X 1" IPS COUPLING-REDUCING PERMASERT 1-1/4" IPS X 2" IPS Permasert Couplings - Copper to PE LP LP LP LP LP COUPLING-COPPER TO PE 1/2" 1/2" CTS TO 1/4" FL COUPLING-COPPER TO PE 1/2" CTS X 3/8" FL COUPLING-COPPER TO PE 1/2" CTS X 1/2" FL COUPLING-COPPER TO PE 1/2" CTS X 5/8" FL COUPLING-COPPER TO PE 1/2" IPS X 1/2" FL 69

70 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Permasert Elbows LP LP LP LP LP ELBOW-1/2" CTS PERMASERT ELBOW-3/4" IPS PERMASERT ELBOW-1" IPS PERMASET ELBOW-1-1/4" IPS PERMASERT ELBOW-2" IPS PERMASERT Permasert Tees - Three Way LP LP LP LP LP LP LP Permasert Tees - Three-Way Reducing LP LP LP LP LP LP LP LP TEE-3 WAY 1/2" CTS PERMASERT TEE-3 WAY 1/2" IPS PERMASERT TEE-3 WAY 3/4" IPS PERMASERT TEE-3 WAY 1" CTS PERMASERT TEE-3 WAY 1" IPS PERMASERT TEE-3 WAY 1-1/4" IPS PERMASERT TEE-3 WAY 2" IPS PERMASERT TEE-3 WAY REDUCING 1/2" CTS X 1/2" CTS X 3/4" IPS PERMASERT TEE-3 WAY REDUCING 3/4" IPS X 3/4" IPS X 1/2" CTS PERMASERT TEE-3 WAY REDUCING 1" CTS X 1" CTS X 1/2" CTS PERMASERT TEE-3 WAY REDUCING 1" IPS X 1" IPS X 3/4" IPS PERMASERT TEE-3 WAY REDUCING 1-14" IPS X 1-1/4" IPS X 3/4"IPS PERMASERT TEE-3 WAY REDUCING 2" IPS X 2" IPS X 1" CTS PERMASERT TEE-3 WAY REDUCING 2" IPS X 2" IPS X 1-1/4" IPS PERMASERT TEE-3 WAY REDUCING 1" IPS X 1" IPS X 1/2" CTS PERMASERT Permasert Tees - Mechanical Tapping LP LP LP LP LP LP TEE-MECH TAPPING 1-1/4" IPS X 1/2" CTS PERMALOCK TEE-MECH TAPPING 1-1/4" IPS X 1" CTS PERMALOCK TEE-MECH TAPPING 1-1/4" IPS X 3/4" IPS PERMALOCK TEE-MECH TAPPING 2" IPS X 1/2" CTS PERMALOCK TEE-MECH TAPPING 2" IPS X 3/4" IPS PERMALOCK TEE-MECH TAPPING 2" IPS X 1" IPS PERMALOCK 70

71 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Permasert Transitions LP LP LP LP LP LP LP LP LP-IBHD TRANSITION-1/2" CTS X 3/4" MPT TRANSITION-1/2" IPS X 3/4" MPT TRANSITION-3/4" IPS X 3/4" MPT TRANSITION-1" CTS X 1" MPT TRANSITION-1" IPS X 1" MPT TRANSITION-1-1/4" IPS X 1-1/4" MPT TRANSITION-2" IPS X 2" MPT COUPLING-1/2" CTS X 3/8" FPT BRASS STIFFNER-1-1/4" X 12" POLY Permasert Stubs - Blind End LP LP LP LP LP Permasert Caps - Blind End LP LP LP LP LP LP STUB-BLIND END 1/2" CTS PERMASERT STUB-BLIND END 3/4" IPS PERMASERT STUB-BLIND END 1" IPS PERMASERT STUB-BLIND END 1-1/4" IPS PERMASERT STUB-BLIND END 2" IPS PERMASERT CAP-BLIND END STOPNGO 1/2" CTS PERMASERT CAP-BLIND END STOPNGO 3/4" IPS PERMASERT CAP-BLIND END STOPNGO 1" CTS PERMASERT CAP-BLIND END STOPNGO 1'' IPS PERMASERT CAP-BLIND END STOPNGO 1-1/4" IPS PERMASERT CAP-BLIND END STOPNGO 2" IPS PERMASERT Permasert Valves - Polyethylene Shut-Off LP LP VALVE-SHUT OFF 1/2" CTS PERMASERT VALVE-SHUT OFF 3/4" IPS PERMASERT 71

72 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Line Risers - Mechanical Ends LP LP LP LP LP LP LP LP LP LP RISER-LINE 1/2" MNPT X 1/2"CTS 18" VERTICAL 18" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"CTS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"CTS 18" VERTICAL 18" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"CTS 22" VERTICAL 18" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 3/4"IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 1" CTS 30" VERTICAL 24" HORIZONTAL RISER-LINE 1" MNPT X 1" IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 1-1/4"MNPT X 1-1/4" IPS 30" VERTICAL 24" HORIZ RISER-LINE 2" MNPT X 2" IPS 30" VERTICAL 15" HORIZONTAL Line Risers - Fusion Ends LP LP LP LP LP LP LP LP Perfection Flex Risers - Servi Sert Ends RISER-LINE 3/4" MNPT X 1/2"CTS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"CTS 22" VERTICAL 18" HORIZONTAL RISER-LINE 3/4" MNPT X 1/2"IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 3/4"IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 3/4" MNPT X 1" CTS 30" VERTICAL 24" HORIZONTAL RISER-LINE 1" MNPT X 1" IPS 30" VERTICAL 24" HORIZONTAL RISER-LINE 1-1/4"MNPT X 1-1/4" IPS 30" VERTICAL 24" HORIZ RISER-LINE 2" MNPT X 2" IPS 30" VERTICAL 15" HORIZONTAL LP LP LP LP LP LP LP-71412R LP LP LP LP LP LP RISER-FLEX 1/2" MNPT X 1/2"CTS 84" OL RISER-FLEX 1/2" MNPT X 1/2"CTS 36" OL RISER-FLEX 3/4" MNPT X 1/2"CTS 84" OL RISER-FLEX 3/4" MNPT X 1/2"CTS 60" OL RISER-FLEX 3/4" MNPT X 1/2"CTS 36" OL RISER-FLEX 3/4" MNPT X 1/2" IPS 36" OAL RISER-FLEX 3/4" MNPT X 3/4" IPS 84" OL RISER-FLEX 3/4" MNPT X 3/4"IPS 60" OL RISER-FLEX 3/4" MNPT X 3/4"IPS 36" OL RISER-FLEX 3/4" MNPT X 1/2"CTS 36" FLEX LENGTH W/15" NIPPLE ADAPTER-SERVICE HEAD 3/4" MPT X 1/2" CTS ADAPTER-SERVICE HEAD 1/2" MPT X 1/2" CTS ADAPTER-SERVICE HEAD 3/4" MPT X 3/4" IPS 72

73 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Chicago Flex Risers LP-XR-10B L-ZD LP-XR-10B ZD LP-XR-10B-8SN-36-L LP-XR-10B-8SN-72-L LP-XR-10B-8SN-96-L LP-XR-17C-10SN-36-L LP-XR-17C-10SN-72-L LP-XR-17C-10SN-96-L LP-A SW RISER-X 3/4" MPT X 1/2" CTS X 36" OAL RISER-X 3/4" MPT X 1/2" CTS X 72" OAL RISER-X 1/2" FEMALE FLARE SWIVEL X 1/2" CTS X 36" OAL RISER-X 1/2" FEMALE FLARE SWIVEL X 1/2" CTS X 72" OAL RISER-X 1/2" FEMALE FLARE SWIVEL X 1/2" CTS X 96" OAL RISER-X 5/8" FEMALE FLARE SWIVEL X 3/4" IPS X 36" OAL RISER-X 5/8" FEMALE FLARE SWIVEL X 3/4" IPS X 72" OAL RISER-X 5/8" FEMALE FLARE SWIVEL X 3/4" IPS X 96" OAL FLARE-HEAD SERVICE 1/2" FF Features and Benefits: Integral swivel service head adapter Quick and reliable mechanical joint Bottoming nut (positive stop) eliminates requirements of torque measurement One piece, bidirectional seal/ferrule assembly eliminates worries of order and orientation of multiple internal components 73

74 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Riser Components - Chicago CHICAGO FITTINGS AND COMPONENTS FOR FIELD ASSEMBLY ARE NOT FOR USE IN IOWA, MINNESOTA, NEBRASKA, NORTH DAKOTA, SOUTH DAKOTA, OR WISCONSIN. LP-FC34 LP-FC11/4 LP-MSS17-10-INV LP-MSS27-17 LP-X2537SW LP-X2707SW LP-X Tools and Accessories HOSE-3/4" FLEX FOR 1/2" CTS 100' ROLL HOSE-1-1/4" FLEX FOR 3/4" IPS 100' ROLL SEAL-MOISTURE 1/2' CTS INVERTE SEAL-MOISTURE 3/4" IPS ADAPTER-1/2" MPT X 1/2" CTS X 3/4" CONDUIT SWIVEL SVE HEAD ADAPTER-3/4" MPT X 1/2" CTS CHICAGO SAFETY ADAPTER-3/4" MPT X 3/4" IPS X 1 1/4" CONDUIT SERVICE HEAD LP TOOL-CHAMF 1/2" CTS X 1" CTS LP TOOL-CHAMF 1/2" CTS X 3/4" IPS LP TOOL-CHAMF 1/2" IPS X 3/4" IPS LP TOOL-CHAMF 3/4" IPS X 1" IPS LP TOOL-CHAMF 1-1/4" IPS LP TOOL-CHAMF 2" IPS LP CUTTER-PLASTIC PIPE 1/2" X 1-1/4" IPS LP-55225B BLADE-FOR LP CUTTER-PLASTIC PIPE 1/2" X 2" IPS LP-55227B BLADE-FOR

75 Tubing, Pipe, Hose and Accessories Polyethylene Pipe and Accessories Pipe and Cable Locating The Cable Hound receiver with DSP noise suppression uses state of the art Digital Signal Processing to filter out virtually all unwanted noise. This allows the user to detect only the 2.7 KHz signal produced by the Cable Hound transmitter. DSP technology offers a dramatic improvement in underground cable locating, especially in high electrical noise environments. Each Cable Hound DSP Kit consists of a transmitter, digital receiver, headphones, tone probe, ground rod and carrying case. The dimensions of the unit are 15.5" x 13.5" x 4" and weighs 4.5 pounds (less batteries). LP LP LP LP-TW-14 LP-TW LOCATOR-LINE DSP CABLEHOUND ROD-GROUND CABLE HOUND TAPE-MARKING 2" X 1000' ROLL UNDERGROUND DETECTION TRACER WIRE-#14 500' ROLL TRACER WIRE-# ' ROLL 75

76 Tubing, Pipe, Hose and Accessories Engine Fuel Engine Fuel Hose LP Gas Engine Fuel Hose Construction: Specially compounded heat resistant synthetic rubber seamless inner tube, single braid of stainless steel wire. The hose is impregnated with oil and mildew resistant rubber compound. UL listed for LPG service. Application: Required for LP gas engine fuel lines. Temperature Rating: -40º to 257º F. Inner tube specially compounded to resist temperatures up to 257º F without cracking. LP-SS4-UL HOSE-SS BRAID CARB 3/16" 350 PSI LP-SS6-UL HOSE-SS BRAID CARB 5/16" 350 PSI LP-SS8-UL HOSE-SS BRAID CARB 13/32" 350 PSI Engine Fuel Hose Fittings LP-6-4MP LP-6FS LP-6FS-45 LP-6FS-90 LP LP LP LP COUPLING-HOSE 5/16" ID CARB X 1/4" MPT COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE 45 DEG COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE 90 DEG COUPLING-HOSE 3/16" ID CARB X 1/4" OD FML FLARE COUPLING-HOSE 3/16" ID CARB X 1/4" OD FML FLARE 90 DEG COUPLING-HOSE 13/32" ID CARB X 1/2" OD FML FLARE COUPLING-HOSE 13/32" ID CARB X 1/2" OD 90 DEG FML FLARE 76

77 Tubing, Pipe, Hose and Accessories Bulk Hose and Accessories Bulk Hose Bulk Hose is available in full reels or cut to length. Tube: Cover: Reinforcement: Temperature Range: Branding: Brand Description: Black Nitrile Perforated Black Neoprene Multiple Textile Spirals -40º F to 180º F (Note: The hose construction is capable of this rating, however, LP gas should never be conveyed over 140º F. Parker 7132 or 7232 CGA Type I Caution - LP gas hose MH6737 UR (UL Recognized component, with backwards R ) Issue number XXXX 350 psi max WP made in USA DE1 (Date Code). Impression Brand 7122 Series liquid petroleum vapor hose is designed for light duty propane vapor line service light duty in applications to 140º F. and 125 psi Series is designed for propane fuel line service on forklift and utility vehicle applications in applications to 140º F. and 350 psi. Parker Series 7132XT X-treme LPG Delivery Hose is an extremely flexible low temperature hose that has improved abrasion resistance for longer life. Available in bulk lengths. Tube: Cover: Reinforcement: Temperature Range: Branding: Brand Description: LP-GLP025 LP LP LP-GLP038 LP-GLP050 LP-GLP075 LP-GLP100 LP-GLP125 LP-GLP150 LP-GLP200 Black Nitrile Perforated Black Neoprene Multiple Textile Spirals -65º F to 180º F (Note: The hose construction is capable of this rating, however, LP gas should never be conveyed over 140º F. Parker X-treme 7132XT Caution LP has hose MH6737 UR US (UL Recognized component, with backwards R ) Issue number XXXX 350 psi max WP made in USA B2 (Date Code). Impression Brand HOSE-1/4" LP 350 PSI TEXTILE SPIRAL HOSE-LP 3/8" LOW PRESSURE "RED HOSE-LP 5/16"SS BRAID W/ BLK RUBBER COVER HOSE-3/8" LP 350 PSI TEXTILE SPIRAL HOSE-1/2" LP 350 PSI TEXTILE SPIRAL HOSE-3/4" LP 350 PSI TEXTILE SPIRAL HOSE-1" LP 350 PSI TEXTILE SPIRAL HOSE-1-1/4" LP 350 PSI TEXTILE SPIRAL HOSE-1-1/2" LP 350 PSI TEXTILE SPIRAL HOSE-2" LP 350 PSI TEXTILE SPIRAL 77

78 Tubing, Pipe, Hose and Accessories Bulk Hose and Accessories Bulk Hose Hose Guard LP-SGW40 WRAP-PLASTIC SPIRAL 2" Bulk Hose Fittings LP-ME COUPLING-HOSE 1/2" 2-BOLT LP-ME COUPLING-HOSE 3/4" 2-BOLT STEEL LP-ME COUPLING-HOSE 1" 2-BOLT LP-ME COUPLING-1-1/4" 2-BOLT LP-ME COUPLING-HOSE 1-1/2" 2-BOLT LP-ME COUPLING-HOSE 2" 2-BOLT LP-ME S COUPLING-SWIVEL 3/4" HB X 1-3/4" FML ACME 2-BOLT LP-ME S COUPLING-SWIVEL HOSE 2" ID X 3-1/4" FML ACME 2 BOLT LP-ME B COUPLING-HOSE 2" ID X 3-1/4" FML ACME BRASS 2 BOLT LP COUPLING-HOSE 3/8" ID X 3/8" MPT BRASS LP COUPLING-HOSE 1/2" ID X 1/2" MPT LP COUPLING-HOSE 3/4" ID X 3/4" MPT COUPLING-HOSE 1" ID X 1" MPT COUPLING-HOSE 1/2" ID X 1-3/4" FML ACME COUPLING-HOSE 3/4" ID X 1-3/4" FML ACME COUPLING-HOSE 1" ID X 1-3/4" FML ACME LP COUPLING-HOSE SWIVEL 3/8" ID X 3/8" FML FLG BRASS LP-1708 COUPLING-HOSE END 1/2" ID X 1/2" FML FL LP S COUPLING-HOSE 1/4" ID X 1/4" MPT LP S COUPLING-HOSE 3/8" ID X 3/8" MPT 78

79 Tubing, Pipe, Hose and Accessories Bulk Hose and Accessories Barb Fittings LP-ME5335 LP-ME4355 LP-4113 LP-ME23C LP-ME23E LP-ME4357 LP-139M LP-ME4631 LP-ME5632 LP-ME4633 LP-562 LP-ME4653 LP-ME5133 LP-ME4231 LP-ME5232 LP-ME4233 LP-676 LP-724 LP-ME4253 LP-ME4254 LP-ME4835 LP-ME4855 FITTING-1/4" HB X 3/8" FML FLA SWIVEL BRASS FITTING-3/8" HB X 3/8" FML FLA SWIVEL BRASS FITTING-1/4" HB X 1/4" FPT BRASS FITTING-1/4" HB X 9/16" LH FML SWIVEL BRASS FITTING-3/8" HB X 9/16" LH FML SWIVEL BRASS FITTING-3/8" HB X 1/2" FML FLA SWIVEL BRASS FITTING-1/4" HB X 1/4" FML FLA SWIVEL BRASS FITTING-1/4" HB X 1/8" FPT BRASS FITTING-1/4" HB X 1/4"FPT BRASS FITTING-1/4" HB X 3/8" FPT BRASS FITTING-3/8" HB X 1/4" FPT BRASS FITTING-3/8" HB X 3/8" FPT BRASS FITTING-1/4" HB X 1/4" INV FLR BRASS FITTING-1/4" HB X 1/8" MPT BRASS FITTING-1/4" HB X 1/4" MPT BRASS FITTING-1/4" HB X 3/8" MPT BRASS FITTING-1/4" HB X 1/2" MPT BRASS FITTING-3/8" HB X 1/4" MPT BRASS FITTING-3/8" HB X 3/8" MPT BRASS FITTING-3/8" HB X 1/2" MPT BRASS FITTING-1/4" HB X 3/8" ML FL BRASS FITTING-3/8" HB X 3/8" ML FL BRASS Menders LP-B106 LP-B108 LP-B110 MENDER-1/4" BRASS HOSE MENDER-3/8" BRASS HOSE MENDER-1/2" BRASS HOSE 79

80 Tubing, Pipe, Hose and Accessories Bulk Hose and Accessories Ferrules LP-ME7325 LP-ME7326 LP-ME7327 LP-ME7328 LP-ME7329 LP-ME7331 LP-ME7332 Clamps - Junior LP-J201 LP-J240 FERRULE-BRASS.562 ID 1" LONG FERRULE-BRASS.593 ID 1" LONG FERRULE-BRASS.625 ID 1" LONG FERRULE-BRASS.656 ID 1" LONG FERRULE-BRASS.687 ID 1" LONG FERRULE-BRASS.750 ID 1" LONG FERRULE-BRASS.781 ID 1" LONG CLAMP-JR 13/16" X 3/8" SS 100/BOX CLAMP-JR 13/16" X 1/4" SS 100/BOX Cutters Crimper LP-TC400 LP-TC0142 LP-FCR100 CUTTER-TUBING/HOSE UP TO 1-1/2" ID RUBBER BLADE-TC400 TUBE CUTTER CRIMPER-BRASS FERRULE BENCH #855 1/4-3/8 ID DOUBLE BRAID 80

81 Tubing, Pipe, Hose and Accessories Hose Assemblies 1/4" Hose Assemblies LP-GLP025-5 LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP /8" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 1/4" X 5' CPLD HOSE ASSY-LP 1/4" X 10' CPLD HOSE ASSY-LP 1/4" X 15' CPLD HOSE ASSY-LP 1/4" X 20' CPLD HOSE ASSY-LP 1/4" X 25' CPLD HOSE ASSY-LP 1/4" X 50' CPLD HOSE ASSY-LP 1/4" X 75' CPLD HOSE ASSY-LP 3/8" X 10' CPLD HOSE ASSY-LP 3/8" X 15' CPLD HOSE ASSY-LP 3/8" X 20' CPLD HOSE ASSY-LP 3/8" X 25' CPLD HOSE ASSY-LP 3/8" X 50' CPLD HOSE ASSY-LP 3/8" X 75' CPLD HOSE ASSY-LP 3/8" X 100' CPLD 1/2" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 1/2" X 10' CPLD HOSE ASSY-LP 1/2" X 15' CPLD HOSE ASSY-LP 1/2" X 20' CPLD HOSE ASSY-LP 1/2" X 25' CPLD HOSE ASSY-LP 1/2" X 30' CPLD HOSE ASSY-LP 1/2" X 40' CPLD HOSE ASSY-LP 1/2" X 50' CPLD HOSE ASSY-LP 1/2" X 75' CPLD HOSE ASSY-LP 1/2" X 100' CPLD 81

82 Tubing, Pipe, Hose and Accessories Hose Assemblies 3/4" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 3/4" X 10' CPLD HOSE ASSY-LP 3/4" X 15' CPLD HOSE ASSY-LP 3/4" X 20' CPLD HOSE ASSY-LP 3/4" X 25' CPLD HOSE ASSY-LP 3/4" X 30' CPLD HOSE ASSY-LP 3/4" X 40' CPLD HOSE ASSY-LP 3/4" X 50' CPLD HOSE ASSY-LP 3/4" X 75' CPLD HOSE ASSY-LP 3/4" X 100' CPLD 1" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP /4" Hose Assemblies HOSE ASSY-LP 1" X 10' CPLD HOSE ASSY-LP 1" X 15' CPLD HOSE ASSY-LP 1" X 20' CPLD HOSE ASSY-LP 1" X 25' CPLD HOSE ASSY-LP 1" X 30' CPLD HOSE ASSY-LP 1" X 40' CPLD HOSE ASSY-LP 1" X 50' CPLD HOSE ASSY-LP 1" X 75' CPLD LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 1-1/4" X 10' CPLD HOSE ASSY-LP 1-1/4" X 15' CPLD HOSE ASSY-LP 1-1/4" X 20' CPLD HOSE ASSY-LP 1-1/4" X 25' CPLD HOSE ASSY-LP 1-1/4" X 30' CPLD HOSE ASSY-LP 1-1/4" X 40' CPLD HOSE ASSY-LP 1-1/4" X 50' CPLD HOSE ASSY-LP 1-1/4" X 60' CPLD HOSE ASSY-LP 1-1/4" X 70' CPLD HOSE ASSY-LP 1-1/4" X 80' CPLD HOSE ASSY-LP 1-1/4" X 90' CPLD 82

83 Tubing, Pipe, Hose and Accessories Hose Assemblies 1-1/2" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 1-1/2" X 10' CPLD HOSE ASSY-LP 1-1/2" X 15' CPLD HOSE ASSY-LP 1-1/2" X 20' CPLD HOSE ASSY-LP 1-1/2" X 30' CPLD 2" Hose Assemblies LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP LP-GLP HOSE ASSY-LP 2" X 10' CPLD HOSE ASSY-LP 2" X 15' CPLD HOSE ASSY-LP 2" X 18' CPLD HOSE ASSY-LP 2" X 20' CPLD HOSE ASSY-LP 2" X 25' CPLD HOSE ASSY-LP 2" X 30' CPLD HOSE ASSY-LP 2" X 50' CPLD 83

84 Tubing, Pipe, Hose and Accessories Copper Tubing LP-1/4K LP-1/4L LP-3/8K LP-3/8L LP-1/2K-100 LP-1/2L-100 LP-3/4K LP-3/4L LP-RF14 LP-RF38 LP-RF LP-RF12 LP-RF LP-RF58 LP-RF LP LP LP LP LP TUBING-COPPER 1/4K 1/4" ID 3/8" OD 100' COIL TUBING-COPPER 1/4L 1/4" ID 3/8" OD 100' COIL TUBING-COPPER 3/8K 3/8" ID 1/2" OD 100' COIL TUBING-COPPER 3/8L 3/8" ID 1/2" OD 100' COIL TUBING-COPPER 1/2K 1/2" ID 5/8" OD 100' COIL TUBING-COPPER 1/2L 1/2" ID 5/8" OD 100' COIL TUBING-COPPER 3/4K 7/8" OD 100' COIL TUBING-COPPER 3/4L 7/8" OD 100' COIL TUBING-COPPER REFRIGERATOR 1/4" 50' COIL TUBING-COPPER REFRIGERATOR 3/8" 50' COIL TUBING-COPPER REFRIGERATOR 3/8" 100' COIL TUBING-COPPER REFRIGERATOR 1/2" 50' COIL TUBING-COPPER REFRIGERATOR 1/2" 100' COIL TUBING-COPPER REFRIGERATOR 5/8" 50' COIL TUBING-COPPER REFRIGERATOR 5/8" 100' COIL TUBING-COPPER COATED 1/4L 3/8" OD 100' COIL TUBING-COPPER COATED 3/8L 1/2" OD 60' COIL TUBING-COPPER COATED 3/8L 1/2" OD 100' COIL TUBING-COPPER COATED 1/2L 5/8" OD 100' COIL TUBING-COPPER COATED 3/4L 7/8" OD 60' COIL 84

85 Tubing, Pipe, Hose and Accessories Copper Tubing Flaring Tools Rolo-Flair Manual Rotary Flaring Tool 945TH-BPD - For soft metal tubing, precision burnished 45º flares in tube sizes from 2 (1/8" O.D.) to 12 (3/4" O.D.) with an easy turn of the handle, for copper and aluminum alloy. Rothenberger Swing-Release Flare Tool - This unique tool offers unmatched flexibility in tube flaring capability. It produces single lap flares on copper, brass, aluminum and mild steel tubing. Tool in conjunction with our Form-A-Gage will form 45º double lap flares on copper, brass, aluminum and mild thin wall steel tubing. Incorporates hex clamp blocks which rotate independently for six tube sizes. Models can be furnished in different tube sizes for 45º or 37º flares on fractional or metric tubes. Note: 37º flares, single-lap only, flares 3/8" x 5/8" OD. Swing away flare cone mount Plastic handle grips H Hardened steel flaring bar forged steel yoke, for sizes 3/4", 7/8", 1" and 1-1/8" O.D. Tempered steel tube clamps US Patent number , LP-945TH-BPD TOOL-COPPER FLARING 45DEG 1/8" OD THRU 3/4" OD SIZE LP-H TOOL-FLARING 3/4"-1-1/8" OD COPPER LP-420 TOOL-COPPER FLARING SWG RELEASE LP CONE-FLARING 99107R FOR 420 LP STRAP-OPEN ROFLARE 99105R FOR 420 LP PIN-FLARING TOOL FOR 420 LP ROLLER-FLARING TOOL FOR 420 Pilot Tubing LP-1/4AL LP-1/4AL-10 TUBING-ALUMINUM PILOT 1/4" COMPLETE 50' ROLL TUBING-ALUMINUM PILOT 1/4" 10' SECTION 85

86 Tubing, Pipe, Hose and Accessories Pilot Tubing Pilot Breakaway Nut LP-R1539 LP-R1633 LP-R2972 LP NUT-BREAKAWAY 1/8" SHORT NUT-BREAKAWAY 1/8" LONG NUT-BREAKAWAY 1/4" LONG NUT-BREAKAWAY 1/4" SHORT Compression Fittings LP-CF-501 SLEEVE-COMPRESSION 3/16" LP-CF-502 SLEEVE-COMPRESSION 1/4" BRASS LP-CF-510 NUT-3/16" COMPRESSION A61B LP-CF-511 NUT-COMPRESSION 1/4" BRASS LP-CF641 NUT-1/4"COMPRESSION & SLEEVE BREAK-AWAY NUT AND SLEEVE Copper Tubing Cutter, Bender and Accessories LP-512 LP-525 LP LP LP LP LP LP-1008 CUTTER-TUBING 1/8"-1-1/8" OD CUTTER-TUBING 1/4"-1-5/8" OD WHEEL-CUTTING FLR/TOOL SPRING-REAMER INDEX 99104R SCREW-REAMER 99019R RING-CUTTER WHEEL 99010R PIN-CUTTER WHEEL 99015R BENDER-TUBING 1/4" X 5/16" X 3/8" TB

87 Tubing, Pipe, Hose and Accessories Brass Fittings Nuts LP-NS4C NUT-SHORT FORGED 1/4" LP-NS4D NUT-SHORT FORGED 5/16" LP-NS4E NUT-SHORT FORGED 3/8" LP-NS4F NUT-SHORT FORGED 1/2" LP-NS4I NUT-SHORT FORGED 5/8" LP-NS4K NUT-SHORT FORGED 3/4" LP-NS4L NUT-SHORT FORGED 7/8" Reducing Nuts LP-NRS4EC NUT-REDUCING 3/8" X 1/4" LP-NRS4FE NUT-REDUCING 1/2" X 3/8" LP-NRS4IF NUT-REDUCING 5/8" X 1/2" Female Connectors LP-46CA LP-46CC LP-46CE LP-46EA LP-46EC LP-46EE LP-46EF LP-46EK LP-46FC LP-46FE LP-46FF LP-46FK LP-46IE LP-46IF LP-46IK CONNECTOR-1/4" OD FLARE X 1/8" FPT CONNECTOR-1/4" OD FLARE X 1/4" FPT CONNECTOR-1/4" OD FLARE X 3/8" FPT CONNECTOR-3/8" OD FLARE X 1/8" FPT CONNECTOR-3/8" OD FLARE X 1/4" FPT CONNECTOR-3/8" OD FLARE X 3/8" FPT CONNECTOR-3/8" OD FLARE X 1/2" FPT CONNECTOR-3/8" OD FLARE X 3/4" FPT CONNECTOR-1/2" OD FLARE X 1/4" FPT CONNECTOR-1/2" OD FLARE X 3/8" FPT CONNECTOR-1/2" OD FLARE X 1/2" FPT CONNECTOR-1/2" OD FLARE X 3/4" FPT CONNECTOR-5/8" OD FLARE X 3/8" FPT CONNECTOR-5/8" OD FLARE X 1/2" FPT CONNECTOR-5/8" OD FLARE X 3/4" FPT 87

88 Tubing, Pipe, Hose and Accessories Brass Fittings Male Connectors LP-48CA LP-48CC LP-48CE LP-48CF LP-48EA LP-48EC LP-48EE LP-48EF LP-48EK LP-48FC LP-48FE LP-48FF LP-48FK LP-48IE LP-48IF LP-48IK LP-48KF LP-48KK LP-48LK Copper Stopper LP CONNECTOR-1/4" OD FLARE X 1/8" MPT CONNECTOR-1/4" OD FLARE X 1/4" MPT CONNECTOR-1/4" OD FLARE X 3/8" MPT CONNECTOR-1/4" OD FLARE X 1/2" MPT CONNECTOR-3/8" OD FLARE X 1/8" MPT CONNECTOR-3/8" OD FLARE X 1/4" MPT CONNECTOR-3/8" OD FLARE X 3/8" MPT CONNECTOR-3/8" OD FLARE X 1/2" MPT CONNECTOR-3/8" OD FLARE X 3/4" MPT CONNECTOR-1/2" OD FLARE X 1/4" MPT CONNECTOR-1/2" OD FLARE X 3/8" MPT CONNECTOR-1/2" OD FLARE X 1/2" MPT CONNECTOR-1/2" OD FLARE X 3/4" MPT CONNECTOR-5/8" OD FLARE X 3/8" MPT CONNECTOR-5/8" OD FLARE X 1/2" MPT CONNECTOR-5/8" OD FLARE X 3/4" MPT CONNECTOR-3/4" OD FLARE X 1/2" MPT CONNECTOR-3/4" OD FLARE X 3/4" MPT CONNECTOR-7/8" OD FLARE X 3/4" MPT COPPER-STOPPER 1/2" OD MALE FLARE FITTING ONLY 88

89 Tubing, Pipe, Hose and Accessories Brass Fittings Elbows LP-49CA LP-49CC LP-49CE LP-49EC LP-49EE LP-49EF LP-49EK LP-49FC LP-49FE LP-49FF LP-49FK LP-49IF LP-49IK LP-54EC LP-54EE LP-54EF LP-54EK LP-54FE LP-54FF LP-54FK LP-54IE LP-54IF LP-54IK LP-55C LP-55E LP-55F LP-55I ELBOW-1/4" OD FLARE X 1/8" MPT ELBOW-1/4" OD FLARE X 1/4" MPT ELBOW-1/4" OD FLARE X 3/8" MPT ELBOW-3/8" OD FLARE X 1/4" MPT ELBOW-3/8" OD FLARE X 3/8" MPT ELBOW-3/8" OD FLARE X 1/2" MPT ELBOW-3/8" OD FLARE X 3/4" MPT ELBOW-1/2" OD FLARE X 1/4" MPT ELBOW-1/2" OD FLARE X 3/8" MPT ELBOW-1/2" OD FLARE X 1/2" MPT ELBOW-1/2" OD FLARE X 3/4" MPT ELBOW-5/8" OD FLARE X 1/2" MPT ELBOW-5/8" OD FLARE X 3/4" MPT ELBOW-3/8" OD FLARE X 1/4" FPT ELBOW-3/8" OD FLARE X 3/8" FPT ELBOW-3/8" OD FLARE X 1/2" FPT ELBOW-3/8" OD FLARE X 3/4" FPT ELBOW-1/2" OD FLARE X 3/8" FPT ELBOW-1/2" OD FLARE X 1/2" FPT ELBOW-1/2" OD FLARE X 3/4" FPT ELBOW-5/8" OD FLARE X 3/8" FPT ELBOW-5/8" OD FLARE X 1/2" FPT ELBOW-5/8" OD FLARE X 3/4" FPT ELBOW-1/4" OD FLARE ELBOW-3/8" OD FLARE ELBOW-1/2" OD FLARE ELBOW-5/8" OD FLARE Unions Unions - Reducing LP-42C LP-42E LP-42F LP-42I LP-42K LP-42L LP-42EC LP-42FC LP-42FE LP-42IE LP-42IF LP-42IK UNION-FULL 1/4" FLARE UNION-FULL 3/8" FLARE UNION-FULL 1/2" FLARE UNION-FULL 5/8" FLARE UNION-FULL 3/4" FLARE UNION-FULL 7/8" FLARE UNION-REDUCING 3/8" X 1/4" FLARE UNION-REDUCING 1/2" X 1/4" FLARE UNION-REDUCING 1/2" X 3/8" FLARE UNION-REDUCING 5/8" X 3/8" FLARE UNION-REDUCING 5/8" X 1/2" FLARE UNION-REDUCING 5/8" X 3/4" FLARE 89

90 Tubing, Pipe, Hose and Accessories Brass Fittings Tees Crosses LP-44C LP-44E LP-44F LP-44I LP-44K LP-45EEC LP-45EEE LP-45EEF LP-45FFE LP-45FFF LP-45IIF LP-44EEC LP-44EEF LP-44EII LP-44FEE LP-44FFC LP-44FFE LP-44FFI LP-44IIE LP-44IIF LP-CIE CROSS-FLARE 3/8" LP-CIF CROSS-FLARE 1/2" LP-C1I CROSS-FLARE 5/8" TEE-1/4" FLARE TEE-3/8" FLARE TEE-1/2" FLARE TEE-5/8" FLARE TEE-3/4" FLARE TEE-3/8" FL X 3/8" FL X 1/4" MPT TEE-3/8" FL X 3/8" FL X 3/8" MPT TEE-3/8" FL X 3/8" FL X 1/2" MPT TEE-1/2" X 1/2" X 3/8" MPT TEE-1/2" X 1/2" X 1/2" MPT TEE-5/8" X 5/8" X 1/2" MPT TEE-3/8"FL X 3/8"FL X 1/4"FL TEE-3/8"FL X 3/8"FL X 1/2"FL TEE-3/8"FL X 5/8"FL X 5/8" MPT TEE-1/2"FL X 3/8"FL X 3/8"FL TEE-1/2"FL X 1/2"FL X 1/4"FL TEE-1/2"FL X 1/2"FL X 3/8"FL TEE-1/2"FL X 1/2"FL X 5/8" MPT TEE-5/8"FL X 5/8"FL X 3/8" MPT TEE-5/8"FL X 5/8"FL X 1/2"FL Swivel Nut Unions LP-US4C NUT-SWIVEL 1/4" LP-US4E NUT-SWIVEL 3/8" LP-US4F NUT-SWIVEL 1/2" LP-US4I NUT-SWIVEL 5/8" Caps LP-N5C CAP-FLARE 1/4" LP-N5D CAP-FLARE 5/16" LP-N5E CAP-FLARE 3/8" LP-N5F CAP-FLARE 1/2" LP-N5I CAP-FLARE 5/8" 90

91 Tubing, Pipe, Hose and Accessories Brass Fittings Plugs LP-P2C LP-P2E LP-P2F LP-P2I PLUG-1/4" MNPT PLUG-3/8" FLARE PLUG-1/2" FLARE PLUG-5/8" FLARE Adapters LP-664CA LP-664CC LP-664EC LP-664FE LP-664FF ADAPTER-1/4" FML FLARE X 1/8" MPT BRASS ADAPTER-1/4" FML FLARE X 1/4" MPT BRASS ADAPTER-3/8" FML FLARE X 1/4" MPT BRASS ADAPTER-1/2" FML FLARE X 3/8" MPT BRASS ADAPTER-1/2" FML FLARE X 1/2" MPT BRASS Dielectric Unions Brass Black Iron LP-ME LP-ME LP-ME LP-ME LP-ME LP-ME UNION-DIELECTRIC 1/2" MPT X 3/8" ML FLARE BRASS UNION-DIELECTRIC 1/2" MPT X 1/2" ML FLARE BRASS UNION-DIELECTRIC 1/2" MPT X 5/8" ML FLARE BRASS UNION-DIELECTRIC 3/4" MPT X 3/8" ML FLARE BRASS UNION-DIELECTRIC 3/4" MPT X 1/2" ML FLARE BRASS UNION-DIELECTRIC 3/4" MPT X 5/8" ML FLARE BRASS UNION-DIELECTRIC 1/2" FPT 200 PSI UNION-DIELECTRIC 3/4" FPT 200 PSI Galvanized G UNION-DIELECTRIC 1/2"FPT GALVANIZED G UNION-DIELECTRIC 3/4"FPT GALVANIZED 91

92 Tubing, Pipe, Hose and Accessories Steel Swivel Adapter Unions Rounded nose in swivel end makes up a tight metal to metal ground joint union with standard male pipe hose couplings SWIVEL-1/4" MPT X 1/4" FPT UNION F SWIVEL-1/4" FPT X 1/4" FPT UNION SWIVEL-3/8" MPT X 3/8" FPT UNION F SWIVEL-3/8" FPT X 3/8" FPT UNION SWIVEL-1/2" MPT X 1/2" FPT UNION F SWIVEL-1/2" FPT X 1/2" FPT UNION SWIVEL-3/4" MPT X 3/4" FPT UNION F SWIVEL-3/4" FPT X 3/4" FPT UNION SWIVEL-1" FPT X 1" MPT UNION F SWIVEL-1" FPT X 1" FPT UNION SWIVEL-1-1/4" FPT X 1-1/4" MPT F SWIVEL-1-1/4" FPT X 1-1/4" FPT SWIVEL-1-1/2" FPT X 1-1/2" F SWIVEL-1-1/2" FPT X 1-1/2" FPT SWIVEL-2" FPT X 2" MPT F SWIVEL-2" FPT X 2" FPT UNION Schedule 40 Black Pipe - Bulk Schedule 40 black iron pipe comes in 21 sections but can be cut to order. Pricing listed is per foot PIPE-BLACK IRON SCH 40 3/8" PIPE-BLACK IRON SCH 40 1/2" PIPE-BLACK IRON SCH 40 3/4" PIPE-BLACK IRON SCH 40 1" PIPE-BLACK IRON SCH /4" PIPE-BLACK IRON SCH /2" PIPE-BLACK IRON SCH 40 2" 92

93 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Nipples NIPPLE-1/4" X CLOSE SCH 40 BLACK IRON NIPPLE-1/4" X 1-1/2" SCH 40 BLACK IRON NIPPLE-1/4" X 2" SCH 40 BLACK IRON NIPPLE-1/4" X 2-1/2" SCH 40 BLACK IRON NIPPLE-1/4" X 3" SCH 40 BLACK IRON NIPPLE-1/4" X 3-1/2" SCH 40 BLACK IRON NIPPLE-1/4" X 4" SCH 40 BLACK IRON NIPPLE-1/4" X 5" SCH 40 BLACK IRON NIPPLE-1/4" X 6" SCH 40 BLACK IRON NIPPLE-1/4" X 8" SCH 40 BLACK IRON NIPPLE-3/8" X CLOSE SCH 40 BLACK IRON NIPPLE-3/8" X 1-1/2" SCH 40 BLACK IRON NIPPLE-3/8" X 2" SCH 40 BLACK IRON NIPPLE-3/8" X 2-1/2" SCH 40 BLACK IRON NIPPLE-3/8" X 3" SCH 40 BLACK IRON NIPPLE-3/8" X 3-1/2" SCH 40 BLACK IRON NIPPLE-3/8" X 4" SCH 40 BLACK IRON NIPPLE-3/8" X 4-1/2" SCH 40 BLACK IRON NIPPLE-3/8" X 5" SCH 40 BLACK IRON NIPPLE-3/8" X 6" SCH 40 BLACK IRON NIPPLE-3/8" X 8" SCH 40 BLACK IRON NIPPLE-1/2" X CLOSE SCH 40 BLACK IRON NIPPLE-1/2" X 1-1/2" SCH 40 BLACK IRON NIPPLE-1/2" X 2" SCH 40 BLACK IRON NIPPLE-1/2" X 2-1/2" SCH 40 BLACK IRON NIPPLE-1/2" X 3" SCH 40 BLACK IRON NIPPLE-1/2" X 3-1/2" SCH 40 BLACK IRON NIPPLE-1/2" X 4" SCH 40 BLACK IRON NIPPLE-1/2" X 4-1/2" SCH 40 BLACK IRON NIPPLE-1/2" X 5" SCH 40 BLACK IRON NIPPLE-1/2" X 5-1/2" SCH 40 BLACK IRON NIPPLE-1/2" X 6" SCH 40 BLACK IRON NIPPLE-1/2" X 7" SCH 40 BLACK IRON NIPPLE-1/2" X 8" SCH 40 BLACK IRON NIPPLE-1/2" X 9" SCH 40 BLACK IRON NIPPLE-1/2" X 10" SCH 40 BLACK IRON NIPPLE-1/2" X 12" SCH 40 BLACK IRON NIPPLE-3/4" X CLOSE SCH 40 BLACK IRON NIPPLE-3/4" X 1-1/2" SCH 40 BLACK IRON NIPPLE-3/4" X 2" SCH 40 BLACK IRON NIPPLE-3/4" X 2-1/2" SCH 40 BLACK IRON NIPPLE-3/4" X 3" SCH 40 BLACK IRON NIPPLE-3/4" X 3-1/2" SCH 40 BLACK IRON NIPPLE-3/4" X 4" SCH 40 BLACK IRON NIPPLE-3/4" X 4-1/2" SCH 40 BLACK IRON NIPPLE-3/4" X 5" SCH 40 BLACK IRON NIPPLE-3/4" X 5-1/2" SCH 40 BLACK IRON NIPPLE-3/4" X 6" SCH 40 BLACK IRON 93

94 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Nipples NIPPLE-3/4" X 7" SCH 40 BLACK IRON NIPPLE-3/4" X 8" SCH 40 BLACK IRON NIPPLE-3/4" X 9" SCH 40 BLACK IRON NIPPLE-3/4" X 10" SCH 40 BLACK IRON NIPPLE-3/4" X 11" SCH 40 BLACK IRON NIPPLE-3/4" X 12" SCH 40 BLACK IRON NIPPLE-1" X CLOSE SCH 40 BLACK IRON NIPPLE-1" X 2" SCH 40 BLACK IRON NIPPLE-1" X 2-1/2" SCH 40 BLACK IRON NIPPLE-1" X 3" SCH 40 BLACK IRON NIPPLE-1" X 3-1/2" SCH 40 BLACK IRON NIPPLE-1" X 4" SCH 40 BLACK IRON NIPPLE-1" X 4-1/2" SCH 40 BLACK IRON NIPPLE-1" X 5" SCH 40 BLACK IRON NIPPLE-1" X 6" SCH 40 BLACK IRON NIPPLE-1" X 7" SCH 40 BLACK IRON NIPPLE-1" X 8" SCH 40 BLACK IRON NIPPLE-1-1/4" X CLOSE SCH 40 BLACK IRON NIPPLE-1-1/4" X 2" SCH 40 BLACK IRON NIPPLE-1-1/4" X 2-1/2" SCH 40 BLACK IRON NIPPLE-1-1/4" X 3" SCH 40 BLACK IRON NIPPLE-1-1/4" X 3-1/2" SCH 40 BLACK IRON NIPPLE-1-1/4" X 4" SCH 40 BLACK IRON NIPPLE-1-1/4" X 5" SCH 40 BLACK IRON NIPPLE-1-1/4" X 6" SCH 40 BLACK IRON NIPPLE-1-1/4" X 7" SCH 40 BLACK IRON NIPPLE-1-1/4" X 8" SCH 40 BLACK IRON NIPPLE-1-1/2" X CLOSE SCH 40 BLACK IRON NIPPLE-1-1/2" X 2" SCH 40 BLACK IRON NIPPLE-1-1/2" X 2-1/2" SCH 40 BLACK IRON NIPPLE-1-1/2" X 3" SCH 40 BLACK IRON NIPPLE-1-1/2" X 3-1/2" SCH 40 BLACK IRON NIPPLE-1-1/2" X 4" SCH 40 BLACK IRON NIPPLE-2" X CLOSE SCH 40 BLACK IRON NIPPLE-2" X 2-1/2" SCH 40 BLACK IRON NIPPLE-2" X 3" SCH 40 BLACK IRON NIPPLE-2" X 3-1/2" SCH 40 BLACK IRON NIPPLE-2" X 4" SCH 40 BLACK IRON NIPPLE-2" X 4-1/2" SCH 40 BLACK IRON NIPPLE-2" X 5" SCH 40 BLACK IRON NIPPLE-2" X 6" SCH 40 BLACK IRON NIPPLE-2" X 7" SCH 40 BLACK IRON NIPPLE-2" X 8" SCH 40 BLACK IRON NIPPLE-3" X CLOSE SCH 40 BLACK IRON NIPPLE-3" X 4" SCH 40 BLACK IRON NIPPLE-3" X 6" SCH 40 BLACK IRON NIPPLE-3" X 8" SCH 40 BLACK IRON 94

95 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Nipple Assortment Box NIPPLE TRAY-3/8" BLACK SCH 40 6 EACH CLOSE -6" NIPPLE TRAY-1/2" BLACK SCH 40 6 EACH -6" NIPPLE TRAY-3/4" BLACK SCH 40 6 EACH -6" NIPPLE TRAY-1" BLACK SCH 40 6 EACH -6" Couplings Elbows - 45 Degree COUPLING-1/8" FPT SCH 40 BLACK IRON COUPLING-1/4" FPT SCH 40 BLACK IRON COUPLING-3/8" FPT SCH 40 BLACK IRON COUPLING-1/2" FPT SCH 40 BLACK IRON COUPLING-3/4" FPT SCH 40 BLACK IRON COUPLING-1" FPT SCH 40 BLACK IRON COUPLING-1-1/4" FPT SCH 40 BLACK IRON COUPLING-1-1/2" FPT SCH 40 BLACK IRON COUPLING-2" FPT SCH 40 BLACK IRON COUPLING-3" FPT SCH 40 BLACK IRON ELBOW-45 DEG 1/8" SCH 40 BLACK IRON ELBOW-45 DEG 1/4" SCH 40 BLACK IRON ELBOW-45 DEG 3/8" SCH 40 BLACK IRON ELBOW-45 DEG 1/2" SCH 40 BLACK IRON ELBOW-45 DEG 3/4" SCH 40 BLACK IRON ELBOW-45 DEG 1" SCH 40 BLACK IRON ELBOW-45 DEG 1-1/4" SCH 40 BLACK IRON ELBOW-45 DEG 1-1/2" SCH 40 BLACK IRON ELBOW-45 DEG 2" SCH 40 BLACK IRON ELBOW-45 DEG 3" SCH 40 BLACK IRON Elbows - 90 Degree ELBOW-90 DEG 1/8" SCH 40 BLACK IRON ELBOW-90 DEG 1/4" SCH 40 BLACK IRON ELBOW-90 DEG 3/8" SCH 40 BLACK IRON ELBOW-90 DEG 1/2" SCH 40 BLACK IRON ELBOW-90 DEG 3/4" SCH 40 BLACK IRON ELBOW-90 DEG 1" SCH 40 BLACK IRON ELBOW-90 DEG 1-1/4" SCH 40 BLACK IRON ELBOW-90 DEG 1-1/2" SCH 40 BLACK IRON ELBOW-90 DEG 2" SCH 40 BLACK IRON ELBOW-90 DEG 3" SCH 40 BLACK IRON 95

96 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Elbows - 90 Degree Street ELBOW-90 DEG STR 1/8" SCH 40 BLACK IRON ELBOW-90 DEG STR 1/4" SCH 40 BLACK IRON ELBOW-90 DEG STR 3/8" SCH 40 BLACK IRON ELBOW-90 DEG STR 1/2" SCH 40 BLACK IRON ELBOW-90 DEG STR 3/4" SCH 40 BLACK IRON ELBOW-90 DEG STR 1" SCH 40 BLACK IRON ELBOW-90 DEG STR 1-1/4" SCH 40 BLACK IRON ELBOW-90 DEG STR 1-1/2" SCH 40 BLACK IRON ELBOW-90 DEG STR 2" SCH 40 BLACK IRON ELBOW-90 DEG STR 3" SCH 40 BLACK IRON Tees - Female Crosses TEE-1/8" SCH 40 BLACK IRON TEE-1/4" SCH 40 BLACK IRON TEE-3/8" SCH 40 BLACK IRON TEE-1/2" SCH 40 BLACK IRON TEE-3/4" SCH 40 BLACK IRON TEE-1" SCH 40 BLACK IRON TEE-1-1/4" SCH 40 BLACK IRON TEE-1-1/2" SCH 40 BLACK IRON TEE-2" SCH 40 BLACK IRON TEE-3" SCH 40 BLACK IRON CROSS-1/8" SCH 40 BLACK IRON CROSS-1/4" SCH 40 BLACK IRON CROSS-3/8" SCH 40 BLACK IRON CROSS-1/2" SCH 40 BLACK IRON CROSS-3/4" SCH 40 BLACK IRON CROSS-1" SCH 40 BLACK IRON CROSS-1-1/4" SCH 40 BLACK IRON CROSS-1-1/2" SCH 40 BLACK IRON CROSS-2" SCH 40 BLACK IRON 96

97 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Bushings - Hex Reducer BUSHING-HEX 1/4" X 1/8" SCH 40 BLACK IRON BUSHING-HEX 3/8" X 1/8" SCH 40 BLACK IRON BUSHING-HEX 1/2" X 3/8" SCH 40 BLACK IRON BUSHING-HEX 3/4" X 1/2" SCH 40 BLACK IRON BUSHING-HEX 1" X 3/4" SCH 40 BLACK IRON BUSHING-HEX 1-1/4" X 3/4" SCH 40 BLACK IRON BUSHING-HEX 1-1/4" X 1" SCH 40 BLACK IRON BUSHING-HEX 1-1/2" X 1-1/4" SCH 40 BLACK IRON BUSHING-HEX 2" X 1-1/2" SCH 40 BLACK IRON BUSHING-HEX 3" X 2" SCH 40 BLACK IRON Reducers - Bell RED BELL 1/4" X 1/8" SCH 40 BLACK IRON RED-BELL 3/8" X 1/4" SCH 40 BLACK IRON RED BELL 3/8" X 1/8" SCH 40 BLACK IRON RED BELL 1/2" X 3/8" SCH 40 BLACK IRON RED BELL 1/2" X 1/4" SCH 40 BLACK IRON RED-BELL 3/4" X 1/2" SCH 40 BLACK IRON RED-BELL 3/4" X 3/8" SCH 40 BLACK IRON RED-BELL 3/4" X 1/4" SCH 40 BLACK IRON RED-BELL 1" X 3/4" SCH 40 BLACK IRON RED-BELL 1" X 1/2" SCH 40 BLACK IRON RED-BELL 1-1/4" X 1" SCH 40 BLACK IRON RED-BELL 1-1/4" X 3/4" SCH 40 BLACK IRON RED-BELL 1-1/2" X 1-1/4" SCH 40 BLACK IRON RED-BELL 1-1/2" X 1" SCH 40 BLACK IRON RED-BELL 1-1/2" X 3/4" SCH 40 BLACK IRON RED-BELL 2" X 1-1/2" SCH 40 BLACK IRON RED-BELL 2" X 1-1/4" SCH 40 BLACK IRON RED-BELL 2" X 1" SCH 40 BLACK IRON RED-BELL 2" X 1/2" SCH 40 BLACK IRON RED-BELL 3" X 2" SCH 40 BLACK IRON Unions, Ground Joints with Brass Seat UNION-1/4" FPT BRASS SEAT SCH 40 BLACK IRON UNION-3/8" FPT BRASS SEAT SCH 40 BLACK IRON UNION-1/2" BRASS SEAT SCH 40 BLACK IRON UNION-3/4" BRASS SEAT SCH 40 BLACK IRON UNION-1" BRASS SEAT SCH 40 BLACK IRON UNION-1-1/4" BRASS SEAT SCH 40 BLACK IRON UNION-1-1/2" BRASS SEAT SCH 40 BLACK IRON UNION-2" BRASS SEAT SCH 40 BLACK IRON 97

98 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Caps CAP-1/8" SCH 40 BLACK IRON CAP-1/4" SCH 40 BLACK IRON CAP-3/8" SCH 40 BLACK IRON CAP-1/2" SCH 40 BLACK IRON CAP-3/4" SCH 40 BLACK IRON CAP-1" SCH 40 BLACK IRON CAP-1-1/4" SCH 40 BLACK IRON CAP-1-1/2" SCH 40 BLACK IRON CAP-2" SCH 40 BLACK IRON CAP-3" SCH 40 BLACK IRON Plugs PLUG-SQ HEAD 1/4" SCH 40 BLACK IRON PLUG-SQ HEAD 3/8" SCH 40 BLACK IRON PLUG-SQ HEAD 1/2" SCH 40 BLACK IRON PLUG-SQ HEAD 3/4" SCH 40 BLACK IRON PLUG-1" FORGED STEEL 3M-6M PLUG-1-1/4" FORGED STEEL 3M-6M PLUG-1-1/2" FORGED STEEL 3M-6M PLUG-2" FORGED STEEL 3M-6M PLUG-SQ HEAD 2-1/2" SCH 80 BLACK IRON XH PLUG-HEX HEAD 3" FORGED STEEL 98

99 Tubing, Pipe, Hose and Accessories Schedule 40 Black Iron Fittings Drip Kits LP LP LP Schedule 80 XH Black Pipe - Bulk DRIP KIT-3/8" SCH 40 BLACK IRON DRIP KIT-1/2" SCH 40 BLACK IRON DRIP KIT-3/4" SCH 40 BLACK IRON Schedule 80 black iron pipe comes in 21' sections but can be cut to order. Pricing listed is per foot PIPE-BLACK IRON SCH 80 1/2" PIPE-BLACK IRON SCH 80 3/4" PIPE-BLACK IRON SCH 80 1" PIPE-BLACK IRON SCH /4" PIPE-BLACK IRON SCH /2" PIPE-BLACK IRON SCH 80 2" PIPE-BLACK IRON SCH 80 3" PIPE-BLACK IRON SCH 80 1" SEAMLESS PIPE-BLACK IRON SCH /4" SEAMLESS PIPE-BLACK IRON SCH 80 2" SEAMLESS PIPE-BLACK IRON SCH 80 3" SEAMLESS 99

100 Forged Steel Fittings Nipples NIPPLE-1/4" X CLOSE SCH 80 BLACK IRON XH NIPPLE-1/4" X 1-1/2" SCH 80 BLACK IRON XH NIPPLE-1/4" X 2" SCH 80 BLACK IRON XH NIPPLE-1/4" X 3" SCH 80 BLACK IRON XH NIPPLE-1/4" X 4" SCH 80 BLACK IRON XH NIPPLE-1/4" X 5" SCH 80 BLACK IRON XH NIPPLE-1/4" X 6" SCH 80 BLACK IRON XH NIPPLE-3/8" X CLOSE SCH 80 BLACK IRON XH NIPPLE-3/8" X 1-1/2" SCH 80 BLACK IRON XH NIPPLE-3/8" X 2" SCH 80 BLACK IRON XH NIPPLE-3/8" X 3" SCH 80 BLACK IRON XH NIPPLE-3/8" X 4" SCH 80 BLACK IRON XH NIPPLE-3/8" X 6" SCH 80 BLACK IRON XH NIPPLE-1/2" X CLOSE SCH 80 BLACK IRON XH NIPPLE-1/2" X 1-1/2" SCH 80 BLACK IRON XH NIPPLE-1/2" X 2" SCH 80 BLACK IRON XH NIPPLE-1/2" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-1/2" X 3" SCH 80 BLACK IRON XH NIPPLE-1/2" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-1/2" X 4" SCH 80 BLACK IRON XH NIPPLE-1/2" X 4-1/2" SCH 80 BLACK IRON XH NIPPLE-1/2" X 5" SCH 80 BLACK IRON XH NIPPLE-1/2" X 6" SCH 80 BLACK IRON XH NIPPLE-1/2" X 7" SCH 80 BLACK IRON XH NIPPLE-1/2" X 8" SCH 80 BLACK IRON XH NIPPLE-3/4" X CLOSE SCH 80 BLACK IRON XH NIPPLE-3/4" X 1-1/2" SCH 80 BLACK IRON XH NIPPLE-3/4" X 2" SCH 80 BLACK IRON XH NIPPLE-3/4" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-3/4" X 3" SCH 80 BLACK IRON XH NIPPLE-3/4" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-3/4" X 4" SCH 80 BLACK IRON XH NIPPLE-3/4" X 4-1/2" SCH 80 BLACK IRON XH NIPPLE-3/4" X 5" SCH 80 BLACK IRON XH NIPPLE-3/4" X 6" SCH 80 BLACK IRON XH NIPPLE-3/4" X 7" SCH 80 BLACK IRON XH NIPPLE-3/4" X 8" SCH 80 BLACK IRON XH NIPPLE-1" X CLOSE SCH 80 BLACK IRON XH NIPPLE-1" X 2" SCH 80 BLACK IRON XH NIPPLE-1" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-1" X 3" SCH 80 BLACK IRON XH NIPPLE-1" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-1" X 4" SCH 80 BLACK IRON XH NIPPLE-1" X 4-1/2" SCH 80 BLACK IRON XH NIPPLE-1" X 5" SCH 80 BLACK IRON XH NIPPLE 1" X 5-1/2" SCH 80 BLACK IRON XH NIPPLE-1" X 6" SCH 80 BLACK IRON XH NIPPLE-1" X 7" SCH 80 BLACK IRON XH NIPPLE-1" X 8" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X CLOSE SCH 80 BLACK IRON XH

101 Tubing, Pipe, Hose and Accessories Forged Steel Fittings Nipples NIPPLE-1-1/4" X 2" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 3" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 4" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 4-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 5" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 5-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 6" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 7" SCH 80 BLACK IRON XH NIPPLE-1-1/4" X 8" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X CLOSE SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 2" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 3" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 4" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 5" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 6" SCH 80 BLACK IRON XH NIPPLE-1-1/2" X 8" SCH 80 BLACK IRON XH NIPPLE-2" X CLOSE SCH 80 BLACK IRON XH NIPPLE-2" X 2-1/2" SCH 80 BLACK IRON XH NIPPLE-2" X 3" SCH 80 BLACK IRON XH NIPPLE-2" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-2" X 4" SCH 80 BLACK IRON XH NIPPLE-2" X 5" SCH 80 BLACK IRON XH NIPPLE-2" X 6" SCH 80 BLACK IRON XH NIPPLE-2" X 7" SCH 80 BLACK IRON XH NIPPLE-2" X 8" SCH 80 BLACK IRON XH NIPPLE-3" X CLOSE SCH 80 BLACK IRON XH NIPPLE-3" X 3" SCH 80 BLACK IRON XH NIPPLE-3" X 3-1/2" SCH 80 BLACK IRON XH NIPPLE-3" X 4" SCH 80 BLACK IRON XH NIPPLE-3" X 4-1/2" SCH 80 BLACK IRON XH NIPPLE-3" X 5" SCH 80 BLACK IRON XH NIPPLE-3" X 6" SCH 80 BLACK IRON XH NIPPLE-3" X 8" SCH 80 BLACK IRON XH 101

102 Tubing, Pipe, Hose and Accessories Forged Steel Fittings Nipples - Swage NIPPLE-1" MPT X 3/4" MPT XH-REDUCING NIPPLE-1-1/4" MPT X 1/2" MPT XH-REDUCING NIPPLE-1-1/4"MPT X 3/4" MPT XH-REDUCING NIPPLE-1-1/4" MPT X 1" MPT XH-REDUCING NIPPLE-1-1/2" MPT X 1-1/4" MPT XH-REDUCING NIPPLE-2" MPT X 1" MPT XH-REDUCING NIPPLE-2" MPT X 1-1/4" MPT XH-REDUCING NIPPLE-2" MPT X 1-1/2" MPT XH-REDUCING NIPPLE-3" MPT X 2" MPT XH-REDUCING Couplings Elbows - 45 Degree COUPLING-1/8" FORGED STEEL 3000# COUPLING-1/4" FORGED STEEL 3000# COUPLING-3/8" FORGED STEEL 3000# COUPLING-3/4" FORGED STEEL 3000# COUPLING-1/2" FORGED STEEL 3000# COUPLING-1" FORGED STEEL 3000# COUPLING-1-1/4" FORGED STEEL 3000# COUPLING-1-1/2" FORGED STEEL 3000# COUPLING-2" FORGED STEEL 3000# COUPLING-3" FORGED STEEL 3000# ELBOW-45 DEG 1/2" FORGED STEEL 2000# ELBOW-45 DEG 3/4" FORGED STEEL 2000# ELBOW-45 DEG 1" FORGED STEEL 2000# ELBOW-45 DEG 1-1/4" FORGED STEEL 2000# ELBOW-45 DEG 1-1/2" FORGED STEEL 2000# ELBOW-45 DEG 2" FORGED STEEL 2000# ELBOW-45 DEG 3" FORGED STEEL 2000# Elbows - 90 Degree ELBOW-90 DEG 1/2" FORGED STEEL 2000# ELBOW-90 DEG 3/4" FORGED STEEL 2000# ELBOW-90 DEG 1" FORGED STEEL 2000# ELBOW-90 DEG 1-1/4" FORGED STEEL 2000# ELBOW-90 DEG 1-1/2" FORGED STEEL 2000# ELBOW-90 DEG 2" FORGED STEEL 2000# ELBOW-90 DEG 3" FORGED STEEL 2000# 102

103 Tubing, Pipe, Hose and Accessories Forged Steel Fittings Elbows - 90 Degree Street ELBOW-90 DEG STREET 1/4" FORGED STEEL 3000# ELBOW-90 DEG STREET 3/8" FORGED STEEL 3000# ELBOW-90 DEG STREET 1/2" FORGED STEEL 3000# ELBOW-90 DEG STREET 3/4" FORGED STEEL 3000# ELBOW-90 DEG STREET 1" FORGED STEEL 3000# ELBOW-90 DEG STREET 1-1/4" FORGED STEEL 3000# ELBOW-90 DEG STREET 1-1/2" FORGED STEEL 3000# ELBOW-90 DEG STREET 2" FORGED STEEL 3000# ELBOW-90 DEG STR 3" SCH 80 BLACK IRON XH Tees XH Crosses TEE-1/4" FORGED STEEL 2000# TEE-3/8" FORGED STEEL 2000# TEE-1/2" FORGED STEEL 2000# TEE-3/4" FORGED STEEL 2000# TEE-1" FORGED STEEL 2000# TEE-1-1/4" FORGED STEEL 2000# TEE-1-1/2" FORGED STEEL 2000# TEE-2" FORGED STEEL 2000# TEE-3" FORGED STEEL 2000# CROSS-1/2" FORGED STEEL 2000# CROSS-3/4" FORGED STEEL 2000# CROSS-1" FORGED STEEL 2000# CROSS-1-1/4" FORGED STEEL 2000# CROSS-2" FORGED STEEL 2000# 103

104 Tubing, Pipe, Hose and Accessories Forged Steel Fittings Bushings - Forged Steel Reducers - Bell BUSHING-HEX 3/8" X 1/4" FORGED STEEL BUSHING-HEX 1/2" X 1/8" FORGED STEEL BUSHING-HEX 1/2" X 1/4" FORGED STEEL BUSHING-HEX 1/2" X 3/8" FORGED STEEL BUSHING-HEX 3/4" X 1/4" FORGED STEEL BUSHING-HEX 3/4" X 3/8" FORGED STEEL BUSHING-HEX 3/4" X 1/2" FORGED STEEL BUSHING-HEX 1" X 1/4" FORGED STEEL BUSHING-HEX 1" X 1/2" FORGED STEEL BUSHING-HEX 1" X 3/4" FORGED STEEL BUSHING-HEX 1-1/4" X 1/2" FORGED STEEL BUSHING-HEX 1-1/4" X 3/4" FORGED STEEL BUSHING-HEX 1-1/4" X 1" FORGED STEEL BUSHING-HEX 1-1/2" X 3/4" FORGED STEEL BUSHING-HEX 1-1/2" X 1" FORGED STEEL BUSHING-HEX 1-1/2" X 1-1/4" FORGED STEEL BUSHING-HEX 2" X 3/4" FORGED STEEL BUSHING-HEX 2" X 1" FORGED STEEL BUSHING-HEX 2" X 1-1/4" FORGED STEEL BUSHING-HEX 2" X 1-1/2" FORGED STEEL BUSHING-HEX 3" X 1-1/4" FORGED STEEL BUSHING-HEX 3" X 2" FORGED STEEL COUPLING-RED 3/8" X 1/4" FORGED STEEL 3000# COUPLING-RED 3/8" X 1/2" FORGED STEEL 3000# COUPLING-RED 1/2" X 1/4" FORGED STEEL 3000# COUPLING-RED 3/4" X 1/2" FORGED STEEL 3000# COUPLING-RED 3/4" X 3/8" FORGED STEEL 3000# COUPLING-RED 3/4" X 1/4" FORGED STEEL 3000# COUPLING-RED 1" X 3/4" FORGED STEEL 3000# COUPLING-RED 1" X 1/2" FORGED STEEL 3000# COUPLING-RED 1" X 3/8" FORGED STEEL 3000# COUPLING-RED 1-1/4" X 1" FORGED STEEL 3000# COUPLING-RED 1-1/4" X 3/4" FORGED STEEL 3000# COUPLING-RED 1-1/2" X 1-1/4" FORGED STEEL 3000# COUPLING-RED 1-1/2" X 1" FORGED STEEL 3000# COUPLING-RED 1-1/2" X 3/4" FORGED STEEL 3000# COUPLING-RED 2" X 1-1/2" FORGED STEEL 3000# COUPLING-RED 2" X 1-1/4" FORGED STEEL 3000# COUPLING-RED 2" X 1" FORGED STEEL 3000# COUPLING-RED 2" X 3/4" FORGED STEEL 3000# COUPLING-RED 3" X 2-1/2" FORGED STEEL 3000# COUPLING-RED 3" X 2" FORGED STEEL 3000# 104

105 Tubing, Pipe, Hose and Accessories Forged Steel Fittings Unions UNION-1/2" FORGED STEEL UNION-3/4" FORGED STEEL UNION-1" FORGED STEEL UNION-1-1/4" FORGED STEEL UNION-1-1/2" FORGED STEEL UNION-2" FORGED STEEL UNION-3" FORGED STEEL Caps - Forged Steel Plugs CAP-1/8" FORGED STEEL CAP-1/4" FORGED STEEL CAP-3/8" FORGED STEEL CAP-1/2" FORGED STEEL CAP-3/4" FORGED STEEL CAP-1" FORGED STEEL CAP-1-1/4" FORGED STEEL CAP-1-1/2" FORGED STEEL CAP-2" FORGED STEEL CAP-2-1/2" FORGED STEEL CAP-3" FORGED STEEL PLUG-SQ HEAD 1/2" SCH 40 BLACK IRON PLUG-3/4" FORGED STEEL 3M-6M PLUG-1" FORGED STEEL 3M-6M PLUG-1-1/4" FORGED STEEL 3M-6M PLUG-1-1/2" FORGED STEEL 3M-6M PLUG-2" FORGED STEEL 3M-6M PLUG-HEX HEAD 3" FORGED STEEL 105

106 Tubing, Pipe, Hose and Accessories Pipe Wrap and Primer Wonder Wrap Tape is sticky, stretches just right, and won't tear or unravel. It comes in 2" and 4" rolls. There are plenty of pipe wrap tapes on the market but it's hard to beat Wonder tape. It is UPC Approved/IAPMO Listed, provides excellent insulation with a durable polyethylene backing. It is ideal for iron and steel and is corrosion resistant. It has a super tack adhesion for extra holding power. It is used a lot by underground pipe contractors and plumbers to protect iron and steel pipe from corrosion due to high acidic or "hot soils". It is also used to protect PVC pipe from corrosion due to ultraviolet rays in above ground installations. Polyken Liquid Adhesive #1027 is idea for hand brush applications to rough, reconditioned or grit blasted pipe surfaces. It provides a uniformly smooth, instant tack surface WRAP-PIPE 2" X 100' ROLL WRAP-PIPE 4" X 100' ROLL PRIMER-PIPE QUART 106

107 Tubing, Pipe, Hose and Accessories Pipe Wrap and Primer NOTES 107

108 Sealant Rectorseal Number 5 - Color yellow, slow dry, soft set pipe thread compound. Features: Applicable for use on threaded PVC, steel, iron, copper Pressure range gases to 2,600 psi, liquids to 12,000 and fiberglass reinforced pipe up to 1-1/4". psi. Non-seizing breaks out easily without stripping, galling Temperatures minus 50º F. to plus 400º F. or damaging threads. LP and NH3 vapor only max 125 PSI. Brushable to plus 20º F. Brush top can. Rectorseal Number 21 is compounded scientifically from 13 carefully chosen ingredients, making it a dependable sealant for lines carrying numerous types of liquids and gases, including anhydrous ammonia. It is especially applicable for threaded PVC, steel, iron, copper, and fiberglass reinforced pipe. Features: Black in color Brush top applicator Non toxic Versatile Lubricates threads Soft setting Multi-purpose LP and NH3 vapor only Max 125 PSI. Does not dry out in the can Rectorseal Tru-Blu pipe thread sealant with PTFE is a fast dry, flexible set thread sealant designed for high vibration environments such as refrigeration and industrial applications. PTFE has been added to enhance thread lubrication during assembly and break out. Recommended for use on threaded galvanized steel, iron, brass, copper, aluminum, stainless steel, polyethylene, fiberglass, reinforced PVC and CPVC pipe up to 1-1/4". Great for use as a positive lock and seal on threaded fasteners. Conforms to Federal Spec TT-S Available in 1/2 pint or pint size brush top cans. Liquid Teflon Sealant - Easy application liquid Teflon for fast thread sealing. Handy 2 ounce tube or larger cans with dauber applicator. Note: Not recommended for polypropylene fittings. PLS Premium Thread and Gasket Sealant - Smooth, non-hardening, opaque gray paste adheres readily to iron, stainless steel, aluminum, monel, plastics and synthetic rubber compounds. Sets immediately, dries to touch within 24 hours. Brush on to seal pipe joints, plugs, screwed fittings and gasketed connections in steam systems, refineries, gas service, refrigeration systems and chemical plants. Spreads evenly, adheres firmly, no dripping, no run off. Apply once to seal permanently, yet connection can be easily disassembled. Won t wash out or crack from vibration, expansion or contraction. Prevents seizing, galling, rust and corrosion, and is UL approved. Excellent resistance to dilute acids, aliphatic solvents, ammonia, dilute caustic alkali, chlorine, diesel fuel, gasoline, kerosene, jet fuel, LP gas, natural gas, petroleum solvents, heating oils, hydraulic oils, mineral oils, refrigerants and steam. Temperature range: -50º F. to 400º F. Pressure range: to 3,000 psi for gases, 8,000 psi for liquids. Flash point: 110º F. to (44º C.). (Pensky-Martin CC). Continental LED-Plate Number 250 is highly impregnated with pure lead in permanent suspension. It penetrates the minute interstices of the thread surface forming an armored coating that actually plates the thread so that galling can never occur. LP-RE25790 LP-RE25631 LP-RE SEALANT-#5 1-3/4 OZ TUBE RECTORSEAL SEALANT-#5 1/4 PT RECTORSEAL SEALANT-#5 1/2 PT RECTORSEAL

109 Tubing, Pipe, Hose and Accessories Sealant LP-RE25431 SEALANT-#5 PT RECTORSEAL LP-RE28651 SEALANT-#21-1/2 PT RECTORSEAL LP-RE28541 SEALANT-#21 PT RECTORSEAL LP-RE31780 SEALANT-TRU BLUE 1-3/4 OZ TUBE LP-RE31551 SEALANT-TRU BLUE 1/2 PT LP-RE31431 SEALANT-TRU BLU PT LT2 SEALANT-2 OZ LIQUID TEFLON 8000 PSI LIQUID -50/+400 DEG F LT4 SEALANT-4 OZ LIQUID TEFLON 8000 PSI LIQUID -50/+400 DEG F LT8 SEALANT-8 OZ LIQUID TEFLON 8000 PSI LIQUID -50/+400 DEG F LP-PB04 SEALANT-THREAD PLS2 1/4 PT PSI LIQUID -200/+550 DEG LP-PB16 SEALANT-THREAD PLS2 1 PT PSI LIQUID -200/+550 DEG FE570 SEALANT-#250 1 LB LED-PLATE PSI LIQUID DEG F LP-LA44082 TAPE-TEFLON 1/2" X 520" LP-LA44082-Y TAPE-TEFLON 1/2" X 260" YELLOW Leak Detectors Sherlock Leak Detection Bubble Up Fluid for leak testing lines, cylinders, and tanks. Popular Sherlock five second leak detector is fast and dependable, finds even the smallest leaks. Available in regular or low temp for sub-freezing temperatures. Absolutely Safe Non Flammable Product: Contains no oil, grease, fatty acids, ammonias or any other ingredient that could form either a flammable or explosive mixture. Positively safe with oxygen either high or low pressure as well as other compressed gases. Thoroughly tested and approved by both government and commercial laboratories. Apply liquid to connection or surface suspected of leaking and watch for bubble clusters. Large leaks form large bubbles and very fine leaks form white foam which builds up for several minutes. Dries clean: No greasy residue. No need to remove after testing. LP-SH-1 LP-SH-1XT LP-SH-1-55 LP-8-OZ LP-8-D LP-16-OZ LP-BTL-16-CYL-WINT DETECTOR-LEAK 1 GAL BOTTLE DETECTOR-LEAK 1 GAL BOTTLE EXTRA LOW TEMP DETECTOR-LEAK 55 GAL DRUM BOTTLE-8 OZ EMPTY W/DAUBER LEAK DETECTOR BOTTLE-8 OZ LEAK DETECTOR BOTTLE-16 OZ EMPTY W/BRUSH BOTTLE-16 OZ EMPTY W/TRIGGER SPRAYER 109

110 Tubing, Pipe, Hose and Accessories Methanol Methanol drums available in steel only. Methanol Injector Purpose: Fast and efficient method to inject methanol ensuring condensation does not freeze in the propane system. Features: Spark resistant brass connectors and valve. Durable steel construction body. Quick connecting 1 1/4" female acme vapor coupling. Gravity fed for fast, convenient filling. Holds up to 42 ounces of methanol. Weldment powder coated for maximum weather resistance. For use with all multi-valve applications or where vapor recovery systems are in place. Methanol Injection Chart Suggested Amounts: 1 pint of methanol per 100 gallons of capacity 100# ICC or DOT cylinder add 1/8 pint or two fluid ounces 100 gallon container add 1 pint 250 gallon container add 2.5 pints 500 gallon container add 5 pints LP-5PM LP-30-DRUM LP-55-DRUM W169 LP-MEP gallon container add 10 pints 2000 gallon container add 20 pints METHANOL-5 GAL PAIL METHANOL-30 GAL DRUM METHANOL-55 GAL DRUM WRENCH-BUNG METHANOL-INJECTOR 1-1/4" FML COUPLING-HOLDS 42 OZ. Propane Additive LP-PRO2000-V-5 ADDITIVE-PROPANE 5 GAL PAIL 110

111 Cylinders and Accessories Cylinders - Steel Use the M oz cylinder for cooking, heating, recreational, commercial or emergency use. Worthington LPG Cylinders/Steel Competitive pricing on all products. Highest standard of manufacturing quality. Best delivery and service in the industry. UL certification on 20# cylinders. Durabond 2000 powder coat finish. All manufacturing facilities are ISO 9002 certified. Packaged with heavy shipping sleeve for protection. LP-M LP-M1005 LP-M10109 LP LP-10487TC LP-M10502 LP-M10504 LP-M1150 LP-M1220 LP-14990TC LP-M1426 LP-M1428 LP LP-CR420 CYLINDER-PROPANE 1.02 LB DISPOSABLE CYLINDER-5 LB DOT W/OPD VALVE CYLINDER-10 LB DOT W/OPD VALVE CYLINDER-11 LB DOT W/OPD VALVE CYLINDER-20 LB DOT HORIZONTAL W/GAUGE CYLINDER-20 LB DOT VERTICAL OPD QUICK DISCONNECT CYLINDER-20 LB DOT W/OPD VALVE CYLINDER-30 LB DOT W/OPD VALVE CYLINDER-40 LB DOT W/OPD VALVE CYLINDER-VERTICAL 50 LB CYLINDER-60 LB DOT W/POL VALVE CYLINDER-100 LB DOT 10% POL VALVE CYLINDER-100 LB ASME SQUAT W/MULTI-VALVE SITE GAUGE TANK-420 LB DOT PROPANE 111

112 Cylinders and Accessories Cylinders - Forklift Worthington Forklift Cylinders Outstanding service. Highest standard of manufacturing quality used in construction. Rust free, low maintenance, no internal scale. Easily return their investment through savings in repairs, downtime and painting. Easier to handle, aluminum cylinders increase delivery efficiency and decrease lifting injuries. LP-M5560 LP-M5580 LP-M5595 LP-M9315 LP-M9161 LP-M5516 Cylinders - Buffer LP LP-9287TC LP CYLINDER-FORKLIFT 20 LB DOT W/VALVE CYLINDER-FORKLIFT 33 LB STEEL CYLINDER-FORKLIFT 43 LB STEEL CYLINDER-FORKLIFT 33.5 LB ALUMINUM DOT CYLINDER-FORKLIFT 43.5 LB ALUMINUM BRACKET-UNIVERSAL FORKLIFT CYLINDER-BUFFER STEEL 20 LB W/FILL CYLINDER-BUFFER ALUM 20 LB W/FILL CYLINDER-BUFFER ALUM 20 LB W/GAUGE & FILL 112

113 Cylinders and Accessories Exchange Cabinets 20# and Forklift Cylinder Exchange Cabinets Galvanized screen which is powder coated for superior corrosion resistance. Solid galvanized steel shelves, tops and backs, 16 gauge. Reversible door, or double doors with bolted on stainless steel door hinges. Note: Many other sizes in stock or readily available. Please give us a call for more details. LP-UCE-12 LP-UCE-18 LP-UMF-4 LP-UMF-6 LP-UMF-8 LP-UMF12 CABINET-CYL EXCHANGE 20 LB 12 PLACE CABINET-CYL EXCHANGE 20 LB 18 PLACE CABINET-CYL MOTOR FUEL 33 LB 4 PLACE CABINET-CYL MOTOR FUEL 33 LB 6 PLACE CABINET-CYL MOTOR FUEL 33 LB 8 PLACE CABINET-CYL MOTOR FUEL 33 LB 12 PLACE 113

114 Tank Carriers CD 100 Red Dragon Cylinder Dolly - The perfect companion for any Red Dragon torch kit. The CD 100 is ideally suited for LP gas cylinders up to 40 pounds capacity (10 gallons). The single handle on this dolly allows the operator to use a torch in one hand while moving the dolly with the other hand. When the torch is not in operation, it can be placed in the convenient bracket on the dolly handle. Welded tubular steel, two seven inch wheels with dual ball bearings, and a solid 5/8" axle assure years of use from this rugged dolly. Maximum load 100 pounds. CD 505 Red Dragon Cylinder Mover - Designed specifically for hauling 100 pound cylinders! The handles are set wide and angled outward, making it easy to push or pull. Tires on the CD 505 are removable for easy replacement. Heavy gauge square tube steel construction, tires are two-ply pneumatic and mounted on steel wheels with roller bearing on a one inch steel axle. Some assembly required. YANKATANK Tank Handling System Features: One man operation for tanks under 500 gallons. Move tanks quickly with less manpower. Reduce back injuries. Use for tank maintenance. X-Saddle Aluminum X-brace construction, super strong, super light. Angled top, no tank rolling or sloshing of product. White, non-marking rubber bumpers, replaceable. Fits 120 gallon 1000 gallon tanks. Placarding System 4 direction DOT placarding system, meets all DOT rules and regulations. Easy to use and installs in less than one minute. One 2-way right/left strap and 2 end straps front/rear. Great for tight spots where crane trucks will not fit. Comes complete with 10' shock strap, 2 tank dollies and quick release pins. Set of two. 6" wide x 6" high x 16" long, 8 lbs. each. Conforms to DOT special permit Heavy duty construction, powder coated aluminum back plates, white non-marking bumpers. Adjusts from 120 gallon to 1890 gallon tanks decals are coated with a scratch resistant coating and are replaceable. DOT Exemption Strap - Take advantage of the DOT ruling that allows the transport of propane tanks no larger than 500 gallons to return to the plant with up to 80% cap. NOTE: Companies must apply and receive exemption prior to use. Strap has 4 positions: 120, 250, 350, 500 gallon and larger. To comply with exemption requirements: Steel D ring provides steel on steel attachment point. Crane trucks must put tanks on saddles. Strap sleeve protects the tank legs from strap wear. Tank trailers must provide rear impact protection. LP-CD-100 LP-CD-505 LP-YANK A TANK LP-X SADDLE LP-DOT PLACARD SET LP-DOT X STRAP "B" LP-DOT X STRAP "T" LP-DP-J LP-EXEMPTION BUMPER LP-FISK-CABLE 114 DOLLY-CYLINDER DOLLY-CYLINDER DOLLEY-TANK SADDLE-FISK X SADDLE (SET) PLACARD-1075 DOT 4 DIRECTION STRAP-DOT EXEMPTION "BOOM" SET OF TWO STRAP-DOT EXEMPTION "TRAILER" SET OF TWO JACK-PROPANE TANK LIFTING 3000# CAPACITY 13"JACK TRAVEL BUMPER-EXEMPTION EZ-HD ONLY CABLES-FRT/REAR FOR CLASSIC-EZ &EZHD FISK TANK TRAILERS

115 Cylinders and Accessories Tank Carriers LP-FISK-CHARGING LP-FK DUAL WINCH LP-FISK-EZHD CHARGING KIT FOR EZHD WINCH-DUAL FISK TRAILER-LP TANK FISK EZ-HD MODEL DP-J The easy way to lift and level propane tanks up to 1,000 gallons One man can easily perform lifting, leveling, painting and resetting operations on various sizes of propane tanks. Properly set tanks allow for air flow under tank to better combat rusting and pitting. Designed for increased jacking stability, low profile lifting and minimal maintenance. Padded boot prevents tank marring or scratching during use. Built rugged and durable for years of heavy use. Completely portable and compact - weighs approximately 45 pounds with chains. Technical Information Lifting Capacity 3,000 lbs. Jack Travel 13" Net Weight 42 lbs. Shipping Weight 49 lbs. Shipping Dimensions 24" x 14" x 14" The Fisk Tank-Jak is designed to provide a portable means of lifting propane tanks for leveling, painting, resetting, etc... Sturdy construction and adjustable leveling chains allow it to be used on most 500 or 1,000 gallon tanks. The rounded foot allows the jack base to rotate slightly on the ground or support as the tank rotates upon raising. The two pads on the jack extension contact the tank surface to make the lift, while the chains keep it in position. Easily set an LP tank in tighter spots and on uneven ground. Once tank is clear from carrier, LP tank can be hoisted and set from the rear of the carrier as shown. Carrier must be hitched and securely connected to the towing vehicle. First the rear slide collar is moved to the back and locked with hitch pin. Then the rear lifting cable and hook is then used to lift the tank up in the center of the lifting chain. Operator can now easily swing tank into position and set down with remote control. Only Fisk offers this alternative lifting/setting operation for LP tanks. Specifications and Dimensions: Lifting Capacity: 6,000 lbs. Overall Length: 20' 6" Overall Height: 7' 0" Loaded Tank Ground Clearance: 25" Weight: 2,020 lbs. Axles: 7,000 lb. capacity Tires: 7.50 x 16LT, 8 Ply Brakes: Electric Hitch: Adjustable ball size with wheel jacks New EZ-HD comes with stainless steel fenders, boxes, light boxes Straps: (2) 10,000 lb. and side panels. You pick the frame color. Electrical: Fully wired DOT lighting 12V divided drum winch 12V auxiliary battery (not furnished) Fisk EZHD tank trailer comes standard with an electric winch and suspension. Now powder coated. Options: Dual winch Wireless remote Setting block Carrier Exemption bumper kit Charging kit Each unit carries up to 2 setting block 115

116 Cylinders and Accessories Filling Accessories Portable Weigh Beam Floor Scale - Constructed entirely of heavy duty welded fabricated steel bases and electrostatically coated with long life paint, the 854F Series provides portable, fast, accurate performance. This model has a platform size of 19" wide x 28" deep, and with the simplified lever system offers maintenance free, simple operation. Large 5" diameter heavy duty rubolene wheels make the scale easy to roll wherever it is needed. The die cast beam with easy to read numbers can be viewed from the front or back of the scale. Model: 854F100P Capacity: 1,000 lbs. Beam Front: 100 lbs. x 0.5 lb. Beam Back: 100 lbs. x 0.5 lb. Platform Size: 19" x 28" x 71 cm Wheels: Large 5" (13 cm) diameter heavy duty rubolene. Overall Dimensions: 45" H x 24" W x 35" D Shipping Weights: 132 lbs. / 60 kg Type N201 cylinder filling valve fills DOT cylinders by weight and stops the gas supply when specified fill weight is reached. Operated by air pressure, it is designed for beam type scales and requires no electrical or mechanical power. The assembly comes completely piped up and includes special parts that allow the slide weight on the scale to move to zero. A red button appears in the indicator on top of the N201 each time a cylinder is filled to the desired weight Breakaway Coupling with 3/4" NPT Connection - Protects against dangerous drive away on propane dispenser fueling lines. Installed between the pump and filler hose, any severe strain on the hose, such as the vehicle or lift truck pulling away, will cause the coupling to separate. Coupling is valved on both sides and will instantly close on both sides with a loss of about 3cc. of fuel. Saves damage to equipment, distortion of the dispenser plumbing and most important, makes negligible the chance of a fire due to drive away. If coupling is separated, be sure and bleed out lines connected to coupling before attempting to reconnect. LP-854F-100P SCALE-PORTABLE BEAM 1000 LB PLATFORM 19" X 28" LP-N201 VALVE-CYL FILLING 1/2" AUTOMATIC LP-ME860S-6 ADAPTER-BREAKAWAY 3/4" FNPT FLOKILL SAFETY BRACKET STYLE LP-ME861S-6 COUPLING-BREAKAWAY 3/4" FPT LANYARD STYLE LP-A94856L KIT-DISPENSER REFILLING FORKLIFT CYLINDER 116

117 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters Fill Couplings ME515 and Adaptable for all filling requirements, brass construction is durable and spark free. The couplings allow for quick change between fill connections. ME796 QCC QUICK FILL COUPLING Features: Easy to use snap on snap off action for quick fill operation. Durable glass filled nylon handle. All stainless steel internal components. Large bore stainless steel stem for increased flow. Designed for universal right or left hand operation. Provides universal fill connection for all model QCC service valves. ME779N-6 quick acting hose end valves are leading the industry in minimal product loss during disconnection without sacrificing flow. They have instant full on flow with the added protection of a quick closing, self-locking handle to prevent accidental opening of the valve during handling or storage. They are designed to be used at the end of a filling hose on dispensing systems equipped for filling containers with QCC Type 1 OPD or F.POL type valves. ME790 Hose End Adapter For Forklift Cylinder Filling 1/4" MNPT x 1-1/4" F. Acme Spin-on connector with automatic back check. For use on forklift cylinders with safety check connectors LP-ME390 LP-ME515 LP-ME516 LP-ME796 LP-ME779N-6 LP-ME790 COUPLING-ML POL X 1/4" MPT FILLER ADAPTER-FILL ADAPTER-FILL COUPLING QCC BRASS HANDWHEEL ADPATER-QCC QUICK FILLER VALVE X 1/4" MNPT VALVE-QUICK ACTING 3/4" FNPT X 1-5/16" FML ACME/FML QCC ADAPTER-1-1/4" FML ACME X 1/4" FILLER COUPLING Forklift Couplings LP-ME220F LP-ME220M LP-ME220FP COUPLING-FORKLIFT 1-1/4" FML ACME X 1/4" FPT COUPLING-FORKLIFT 1-1/4" ML ACME X 3/8" FPT CAP-BRASS 1-1/4" FEMALE PLUG FORKLIFT 117

118 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters Fisher Male POL Hard Nose x 1/4" MPT Excess Flow LP-F181 VALVE-EX FLO ML POL X 1/4" MPT 1.5 GPM BRASS Fisher Male POL Hard Nose x 9/16" LH Excess Flow LP-F110 VALVE-EX FLO ML POL X 9/16" LH 0.7 GPM BRASS Fisher Male POL Soft Nose x 1/4" MPT Excess Flow LP-F173 VALVE-EX FLO ML POL X 1/4" MPT 0.7 GPM BRASS ME Male POL Hard Nose x 1/4" Barb Full Flow LP-ME5930 ADAPTER-ML POL X 1/4" HB HN ME Male POL Hard Nose x 3/8" Barb Full Flow LP-ME N ADAPTER-ML POL X 3/8" HB HN ME Male POL Hard Nose x 1/4" MPT Full Flow LP-ME318 LP-ME319 LP-ME322 ADAPTER-ML POL X 1/4" MPT HN ADAPTER-ML POL X 1/4" MPT HN ADAPTER-ML POL X 1/4" MPT HN ME Male POL Hard Nose x 1/4" MPT Full Flow 90 LP-ME345 ADAPTER-ML POL X 1/4" MPT ANGLE HN ME Male POL Hard Nose x 1/4" MPT Excess Flow LP-ME1690 ADAPTER-ML POL X 1/4" MPT 0.9 GPM HN 118

119 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters ME Male POL Hard Nose x 9/16" LH Full Flow LP-ME1650 ADAPTER-ML POL X 9/16" LH HN ME Male POL Hard Nose x 9/16" LH Excess Flow LP-ME1689 ADAPTER-ML POL X 9/16" LH 0.9 GPM HN ME Male POL Soft Nose x 1/4" Barb Full Flow LP-ME1656 LP-ME1656AH ADAPTER-ML POL X 1/4" HB PLASTIC HANDWHEEL SN HANDWHEEL-HEX SOFT NOSE BRASS POL X 1/4" HB ME Male POL Soft Nose x 1/4" Barb Excess Flow Handwheel LP-ME1655 ADAPTER-ML POL X 1/4" HB 0.9 GPM PLASTIC HANDWHEEL SN ME Male POL Soft Nose x 1/4" MPT Full Flow LP-ME1629 ADAPTER-ML POL X 1/4" MPT SN ME Male POL Soft Nose x 1/4" MPT Excess Flow LP-ME1638 LP-ME1641 LP-ME1641EX18 ADAPTER-ML POL X 1/4" MPT SN ADAPTER-ML POL X 1/4" MPT 0.7 GPM SN ADAPTER-ML POL X 1/4" MPT 1.8 GMP SN 119

120 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters ME Male POL Soft Nose x 1/4" MPT Full Flow Handwheel LP-ME1654 LP-ME1654AH LP-ME388 ADAPTER-ML POL X 1/4" MPT PLASTIC HANDWHEEL SN ADAPTER-ML POL X 1/4" MPT BRASS HANDWHEEL SN ADAPTER-ML POL X 1/4" MPT BRASS HANDWHEEL SN ME Male POL Soft Nose x 1/4" MPT Excess Flow Handwheel LP-ME1653 ADAPTER-ML POL X 1/4" MPT 0.9 GPM PLASTIC HANDWHEEL SN LP-ME1653AH ADAPTER-ML POL X 1/4" MPT 0.9 GPM BRASS HANDWHEEL SN ME Male POL Soft Nose x 9/16" LH Excess Flow Handwheel LP-ME1645 ADAPTER-ML POL X 9/16" LH PLASTIC HANDWHEEL SN Marshall Excelsior Male POL Full Flow Adapters LP-ME353 LP-ME355 LP-ME356 LP-ME357 ADAPTER-ML POL X 3/8" ML FLR HN ADAPTER-ML POL X 1/2" ML FLR HN ADAPTER-ML POL X 5/8" ML FLR HN ADAPTER-ML POL X 1/2" FPT HN 120

121 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters Marshall Excelsior Male POL Excess Flow Adapters LP-ME353EX18 LP-ME354EX18 LP-ME355EX18 LP-ME356EX18 VALVE-EX FLO ML POL X 3/8" ML FLR 1.8 GPM HN VALVE-EX FLO ML POL X 1/2" MPT 1.8 GPM HN VALVE-EX FLO ML POL X 1/2" ML FLR 1.8 GPM HN VALVE-EX FLO ML POL X 5/8" ML FLR 1.8 GPM HN Female POL Adapters LP-ME284 LP-ME285 LP-ME286 LP-ME287 LP-ME301 LP-ME303 LP-ME305 LP-ME392 LP-ME568 ADAPTER-FML POL X 1/4" MPT ADAPTER-FML POL X 3/8" MPT ADAPTER-FML POL X 1/2" MPT ADAPTER-FML POL X 3/4" MPT ADAPTER-FML POL X 1/4" FPT ADAPTER-FML POL X 1/2" FPT ADAPTER-FML POL X FML POL ADAPTER-FML POL X 1-5/16" FML ACME ADAPTER-FML POL SWIVEL X 1-3/4" FML ACME 121

122 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters QCC 1-5/16" Adapters The Type I (QCC) connectors (ME517, ME518 and ME519 Series) are designed with a built-in excess flow feature and a positive shutoff that will not allow gas to flow until the connector is fully engaged. In case of a fi re the built-in thermal protection on the QCC connector melts allowing the nipple to disengage from the tank connection and stop the flow of propane. These QCC connectors also provide a positive back check seal at disconnect to eliminate the propane in the hose from being released into the atmosphere. To connect a Type I (QCC) connector to a cylinder, close the cylinder valve and the control valves to all connected appliances. Hand tighten the QCC onto the cylinder and slowly open the cylinder valve. If the valve is opened too quickly, the excess flow device will be activated closing the flow of propane to the appliance. If the excess flow device is activated, close appliance control valves and wait 60 seconds to allow pressure in the line to equalize. Additional equalization time may be needed depending on the length of the hose. Turn on appliances by following the manufacturer s suggested lighting procedures. Note: The Type I (QCC) thread replaces the POL connection on 40 pound or less DOT propane cylinders. Application: These adapters are intended to be attached to the LP gas delivery truck hose outlets. All have minimal flow restriction which allows for fast delivery and also gives the user the ability to remove the filler hose in the event that the fill valve fails to close. In the event of a filler valve failure the integral check valve prevents loss of product. Type 1 Filler Coupling Adaptable for all filling requirements. Brass construction is durable and spark free and allows for quick change between fill connections. QCC Quick Fill Coupling Features: Easy to use snap on/off action for quick fill operation. Durable glass filled nylon handle. All stainless steel internal components. Large bore stainless steel stem for increased flow. Designed for universal right or left hand operation. Provides universal fill connection for all model QCC service valves. LP-ME517 LP-ME569 LP-ME517EV LP-ME518 LP-ME519 LP-ME518-25H LP-ME393 LP-ME393HD LP-ME518-38H LP-ME516 LP-ME796 LP-ME393-1 LP-ME399 LP-ME398 ADAPTER-QCC X 1/4" MPT BLACK 70M BTU ADAPTER-TYPE 1 FILLER 1-3/4" F ACME X 1-5/16" ML ACME ADAPTER-QCC PURGE ADAPTER-QCC X 1/4" MPT GREEN 200M BTU ADAPTER-QCC X 1/4" MPT RED THERMAL PROTECTED ADAPTER-QCC X 1/4" HB GREEN 200M BTU ADAPTER-FILL 1-5/16" ML ACME X SN POL COUPLING-1-5/16" ML ACME X ML POL SOFTNOSE W/HANDWHEEL ADAPTER-QCC X 3/8" HB ADAPTER-FILL COUPLING QCC BRASS HANDWHEEL ADPATER-QCC QUICK FILLER VALVE X 1/4" MNPT ADAPTER-QCC ML X 1/4" FPT POL CONVERSION ADAPTER-QCC ML X 1/4" MNPT ADAPTER-QCC ML X ML POL X FML POL SOFT W/ QUICK CLOSE 122

123 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters QCC Caps PV Valve Cover keeps foreign material from entering the QCC1 valve and protects the outside acme threads of the QCC1 valve on barbecue grills. Cover is made of highly resilient rubber to assure a tight seal. LP-PV CAP-RUBBER DUST W/STRAP LP CYL POL Plugs and Caps Heavy Duty POL Plugs - New Safety-Plus Easier-To-Use Design Satisfies The Requirements of NFPA-58, Section NFPA-58 states: Valve outlets on containers of 108 lb. (49kg) water capacity or less shall be equipped with an effective seal such as a plug, cap or an approved quick-closing coupling. This seal shall be in place whenever the container is not connected for use. Features/Benefits: Easy-to-grip large disc facilitates easy turn insertion. Large disc assures faster insertion. Heavy-duty plug seat for snug, tight leak seal. Pressure tested to over 500 psi. Cannot be over-tightened. Strong, flexible anchor strap. LP-ME1699 LP-ME1691 LP-ME970P LP-ME530 LP-ME CAP-FML POL BRASS PLUG-BRASS POL ML PLUG-PLASTIC POL LOCK-POL BULK 12PK W/1KEY KEY-POL LOCKSEAL Large disc makes positive thread alignment into valve port easy. Large disc requires less physical energy to obtain tight, positive seal into valve port. Liquid CGA1550 Adapters LP-ME306 LP-ME308 LP-ME307 ADAPTER-BRASS 1/4" MPT X CGA1550 ADAPTER-FML POL X CGA1550 BRASS ADAPTER ASSY-F.CGA 555 INLET X 9/16-18 LH 123

124 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters Purge Kit LP Gas Purge Kit - Finally, a product that offers a Safer, more Reliable Method for purging your LP Gas Cylinders! NPGA #133-89(a) Purging LP gas containers up to 2,000 water gallon capacity, ASME and DOT containers, including motor fuel containers. All new containers (and in some cases used containers) may contain water, air or other contaminants, and it is essential that these be removed before filling the container and placing it into service. Water vapor present in the gas vapor may cause regulator freeze-up at the inlet. Ensures proper propane purging when used according to instructions Saves time, purge LP gas cylinders in about half the time of current methods Easy to use Environmentally safe Works with standard POL (CGA 510) LP cylinder connections Accommodates New QCC1 gas grill connection LP PURGE KIT-LP GAS Wrenches LP-20-1 LP-20-2 LP-20-3 LP-20-4 LP-20-5 LP-20-6 LP-20-8 LP-MEP122 LP-MEP125 PLUG-POL WRENCH-TORQUE HANDLE-VALVE WRENCH VICE-CHAIN ASSY WRENCH-PLUMBER POT WRENCH-FORKLIFT VALVE WRENCH-CYLINDER VALVES QCC/OPD WRENCH-QCC 2-PIECE FOR INSTALLATION OPD VALVE WRENCH-VALVE REMOVAL SOCKET EXT CROW FOOT Stamp Dies LP-GK04 STAMP-RECERTIFICATION WITH E NUMBER KIT W/LETTER E LP-STA1014 DIE-STAMP 1/4" LETTER E LP-STA1024 DIE-STAMP 1/4" LETTER O LP-STA1031 DIE-STAMP 1/4" LETTER V LP-STA1048 DIE-STAMP 1/4" NUMBER

125 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters 100# Caps and Collars Cylinder Collars - These steel propane cylinder collars are designed to protect the valve installed on a cylinder. An automotive grade powder coat finish provides maximum corrosion resistance. Warning: It is illegal to fill a tank without a protective collar. Without a protective collar serious damage can occur to the cylinder valve which can lead to catastrophic events such as the tank becoming a dangerous projectile, an explosion and/or fire causing property damage, or personal injury or death. LP-M1433 CAP-SCREW ON 100# CYL 3.5" X 6 LP-ME312-5MV COLLAR-CYL 3-1/8" PAINTED W/CUT-OUT LP-ME350MV COLLAR-SCREW ON CYL Vice and Tankfoot Cylinder Clincher - The Cylinder Clincher is a DOT cylinder holder immobilizes the DOT cylinder completely with no slipping! Even holding 100% where extra pulling power was needed to remove the stubborn valves that had been firmly seated for a long period of time in the older cylinders. A quality built, affordable, reliable, and effective tool that allows smooth one hand operation, and to change a valve effortlessly, even while the customer waits. Utilize the Cylinder Clincher to hold the cylinder for date-stamp recertification and have 0% vibration. F TankFoot Tank Stabilizer fits 20 lb., 30 lb. and 40 lb. cylinders and provides a tip proof condition for transporting cylinders. Required for MH14TC and MH26TC heater models. LP-CC100 LP-F CLINCHER-CYLINDER REMOVE VALVES IN DOT CYLINDERS STABILIZER-TANKFOOT & 40 LB CYL 125

126 Cylinders and Accessories Accessories, Connectors, Fittings and Adapters Dandi-Blocks DANDI-BLOCK - Designed for horizontal ASME tanks and meets NFP 58 standards. One block required for each end of tank. These blocks will lift the tank far enough off the ground to allow for tank painting, mowing and other maintenance needs. Durable yet light weight construction that does not retain moisture, green in color. Model Holds gallon vert tank Circular Shape 6 lbs. each Model Holds 120 to 500 gallon tank 5" tall x 10" wide x 26" long 8 lbs. each Model Holds up to 1,000 gallon tank 7" tall x 11" wide x 30" long 10 lbs. each LP LP LP Cathodic Protection BLOCK-DANDI TANK STABILIZER ROUND CR420 BLOCK-DANDI TANK STABILIZER 500 GAL OR LESS BLOCK-DANDI TANK STABILIZER GAL Underground Tank Installation - To make attachment of anode bags easier, American Welding and Tank will be attaching a copper wire to all underground tank shells. Simply strip the end of the wire and connect to the anode bag lead using a wire nut or copper ferrule. No need to weld the anode bag wire to the tank. The 8B Copper Sulfate Probe is made from durable materials to withstand years of use. The half cells can be recharged to assure accurate readings. It is used to test the performance of the anode bag. It takes a voltmeter and a copper sulfate electrode to take a reading. If the reading is greater than volts, the tank is protected at that time. LP-124MB LP-125MB LP-126MB LP-8B ANODE-32# MAG HIGH POTENTIAL ANODE-17# MAG HIGH POTENTIAL ANODE-5# ELECTRODE-COPPER SULFATE POINT 8B 126

127 Propane Tanks Above Ground LP-QS120 LP-QS250 LP-QS500 LP-QS1000 Propane Tanks Underground LP-QS120U LP-QS250U LP-QS500U LP-QS1000U TANK-120 PROPANE DOMESTIC TANK-250 PROPANE DOMESTIC TANK-500 PROPANE DOMESTIC TANK-1000 PROPANE DOMESTIC TANK-120 PROPANE UNDERGROUND TANK-250 PROPANE UNDERGROUND TANK-500 PROPANE UNDERGROUND TANK-1000 PROPANE UNDERGROUND Vapor Gas Meters Liquid Petroleum Gas Metering The Equimeter S-275 was designed especially for the propane industry. The S-275 has been tested and proven for all services, and can particularly measure LP gases from bottle sets, bulk storage and distribution systems to the house. Manufactured under the same exacting quality control requirements as Equimeter s residential gas meters, the S-275 contains the same joint design and utilizes the same corrosion resistant materials that exhibit high lubricity for low differential operation. The major difference is the connections. The S-275 comes with 3/4" FPT connections. The S denotes side connection. Formulas Gallons times = Cubic Meters. Cubic meters times.976 = Gallons. *Cubic Meter is Standard - Gallon Meters are Available. S-275 is Temperature Compensated. Cubic Feet = Gallons LP-S-275 LP-S-275G LP METER-VAPOR 3/4" T/COMP CU/FT METER-VAPOR 3/4" T/COMP GAL INDEX BRACKET-HANGER KIT METER 127

128 Safety Equipment Manometers and Accessories 1212 Slack Tube Manometer Kit - The slack tube manometer features open and close connectors and overpressure safety traps to prevent loss of fluid due to overpressure or sudden surges of pressure. Kit Includes: Slack Tube Manometer, reads pressure to 16" water column. Carrying case, plastic, 9" x 4 1/2" x 2 1/4" 3/4 oz. bottle fluorescein green color concentrate with wetting agent Two 1/8" pipe thread rubber tubing adapters 1/8" to 1/4" pipe thread bushing 3' length 1/4" ID rubber tubing Rubber tubing adapter to fit standard 7/16" diameter spud Violet Gauge Oil Low temperature gauge oil for use in monometers marked W (water). Good to -40º F., specific gravity 1, CPS 1, One Fluid Ounce Bottle Slack Tube Manometer - Handy roll-up type manometer with laboratory accuracy. Furnished with magnetic clips and open and close connectors. 12"-0-12" WC range. Economy Water Manometers - Item with two magnetic clips and an upper clamp for the tubing. LP-1212 KIT-GAS PRESSURE/CASE & ACCES LP-A339 ADAPTER-1/8" NPT TO 3/16" RUBBR 1/8" ID TUBING BRASS LP-A201-3 TUBING-RUBBER 1/4" ID X 3' LONG LP-7100 ADAPTER-RUBBER TUBING FITS 7/16" DIA SPUD LP-008 FLUID-VIOLET GAUGE GOOD TO -40 LP SLACK-TUBE MANOMETER KIT LP MANOMETER-U TUBE LP-ME1331 ADAPTER-GAS CHECK 1/2" OD FLR LP-ME1328 ADAPTER-GAS CHECK 3/8" OD FLR LP-ME1332 ADAPTER-GAS CHECK 5/8" OD FLR LP-2020 KIT-GAS PRESSURE MAGNEHELIC GAUGE 0-20" WC LP-A-432 CASE-MAGNIHELA GAUGE LP-94MON-15 MONOMETER-0-14" WC MONO HYDRO GAUGE LP-85PL02 ADAPTER-MANOMETER PRESS LOCK 128

129 Safety Equipment Manometers and Accessories NOTES 129

130 Test Kits and Presto-Tap PRESTO-TAP LEAK DETECTION SYSTEM - Designed to be carried by drivers and service personnel to perform NFPA leak testing and determining true out of gas situations. The 300 psig gauge reports tank pressure at appropriate ambient temperature and when compared to surrounding temperature readings (within a few degrees, considering atmospheric conditions), will indicate if liquid is present in the tank and if enough pressure is present to support the system. LDS2000RVL - UL listed 1/8" male NPT regulator valve (for regulator tank pressure tap location). Legal throughout the system at available locations - tank pressure regulator taps, 10# and 11" WC regulator locations, inline valve pressure tap location, or at available appliance locations. RV/QA (regulator valve quick adapter) provides access for instruments, either attached directly or by hose barb. QTG16B dual gauge kits are used for leak check testing at intermediate pressure using the 30 psi gauge and testing first stage regulator. The 35" water column gauge is used for testing low pressure second stage regulator set point and lock up pressure. SQTG4B - Four gauge test kit includes a 30 psi gauge, a 300 psi gauge, a 5 psi gauge, a 35" water column gauge and a high pressure block plus six pressure tape valves. The hose quick disconnect allows for attachment of any one of the gauges. A leak check pressure tap valve can be anywhere in the system with the proper gauge attached for leak check testing. TG30B single point gauge assembly with 30 psig gauge, used for leak check tests at intermediate pressure at the outlet of first stage regulators or at the inlet to second stage regulators. KVB multi-point kit contains a gauge assembly with a 30 psi gauge and a built-in regulator that limits the pressure to the gauge to 12 psi so the gauge can be used for leak check testing at intermediate pressure taps or at the tank pressure using the high pressure test block. Kit includes twelve 1/8" NPT pressure tap valves. LOW PRESSURE TEST KIT MEP60P Features: Adjustable gauge can be reset to zero. Capacity: 0 35" WC. Screwdriver included for easy adjustments. Rubber hose with bell. High quality plastic case with metal hinge pin. LP-METL051 SERVICEMAN'S FRIEND - For use with flow meter and other applications. One end of fitting has 1/8" pipe thread, 1/4" pipe thread and special 5/16" x 32 thread. Opposite end has regular hose fitting, also 1/8" straight pipe thread. Hose can be used on either end. Pressure Gauge Adapter and Test Block - The MEJ595 adapter is installed in the outlet of a first stage regulator to indicate the outlet pressure, use with J500 series gauges. Type MEJ600 test block connects to the container valve to check for leaks in the downstream system. Male POL by female POL, test block with psig gauge. LP-VA1 VALVE-PRESSURE 1/8" NPT TYPE A LP-ME10BTK-1-01 ADAPTER-SCREW ON 1/8"FPT X 5/16-32 FEMALE LP-VA1-1 VALVE-PRESSURE 1/8" NPT TYPE A WITH LP-MEJ608B-03 TAG LP-85PC-04 ADAPTER-PRESSURE CHECK 1/4" LP-LDS2000RVL VALVE-PRESSURE 1/8" NPT TYPE B LP ADAPTER-QUICK PRESTO TAP LP-HSA ADAPTER-SCHRAEDER TYPE"A" CONNECTION SWIVEL "A"VALVES 130

131 Safety Equipment Test Kits and Presto-Tap LP-ME60-2 GAUGE-TEST 0-35" WC 1/4" MPT LP-QTG16B KIT-DUAL GAUGE LP-SQTG4B KIT-GAUGE PRESSURE TEST W/QUICK DISCONNECT LP-TG30B GAUGE-TEST 30# LP-KVB KIT-TEST 0-30 PSI W/REGULATOR LP-ME60P-2 GAUGE-ASSY TEST W/CASE & HOSE 0-35" WC ADJ LP-ME60P-5 GAUGE-TEST 0-35" WC ADJ W/HOSE LP-METL051 SERVICEMAN FRIEND-1/8" NPT, 1/4" NPT, X BRB LP-MEJ595 ADAPTER-PRESSURE GAUGE 1/2" MPT X 1/2" FPT X 1/4" FPT LP-MEJ600 BLOCK-TEST MPOL X FPOL W/0-300 PSI GAUGE 131

132 Safety Equipment Gas Detection Equipment Carbon Monoxide, Propane and Methane Gas Detector Model Number HS in-1 detector. Built-in self-diagnostics assures the unit is operating Senses dangerous levels of carbon Monoxide, Propane properly. and Methane Gas. Easily plugs into any standard v AC electrical Two independent 85dB alarm sounds, one for CO, the outlet and samples the air every 2-1/2 minutes. other for methane/liquid propane. Lock tab feature makes the detector tamper proof. Every detector has computerized calibration to help UL 2034 and UL 1484 Certified. eliminate false alarms. 5 year warranty. The Pocket Air Check is a portable, battery operated, solid state instrument intended for use in applications requiring detection of combustible gas leaks. Handheld and highly sensitive, the Pocket Air Check makes finding gas leaks as easy as using a flashlight and at a fraction of what other portable detectors cost. The Pocket Air Check is a toolbox requirement for the HVAC technician, plumber, homeowner or anyone working with combustible gas installations, especially natural gas or propane. Features: Detects Natural Gas, Methane, Propane, Hydrogen and Butane. Locates leaks in pipes, valves, fittings and tanks. Operates up to 8 hours on two AA alkaline batteries. Highly sensitive solid state sensor. Eye catching emergency yellow housing. Only 6" long - fits easily into pocket or tool belt. Sensitivity: 5000 ppm Methane / 2000 ppm Propane. Gas detection products for propane gas service Instruments that provide personal protection from potentially hazardous conditions and help you find the source of combustible gases and CO fast! Sensit TKX combustible gas leak detectors the perfect choice when locating hard to find natural gas or propane gas leaks. Low maintenance and low initial cost make this product the ideal choice for the budget conscious. High sensitivity allows immediate leak detection. Long sensor life. Tick rate control to pinpoint leaks fast. Adjustable tick rate system. Detects many gases and chemicals. Audible and visual indicators. Long battery life. Sensit HXG-2d combustible gas detector is the first affordable gas leak detector with a true digital display. The HXG-2d is intrinsically safe, durable and reliable. The new patent pending electronic tick control is ideal for locating natural, propane and butane gas leaks. Direct PPM readout (0-990 ppm). Backlit display. Direct LEL percent (0-100% LEL). Adjustable alarms. Push button operation. Long life, low cost sensor. Field calibration. Cannot be used to detect carbon monoxide (CO) leakage. LP-HS80504 LP-500A LP LP LP LP LP LP ALARM-CO & LP DETECTOR-POCKET GAS PORTABLE DETECTOR-GAS LEAK COMBUSTIBLE TKX BASIC UNIT DETECTOR-GAS COMBUSTIBLE HXG-2D BASIC UNIT DETECTOR-GAS COMBUSTIBLE LEAK HXG-3 BASIC UNIT DETECTOR-GAS GOLD G2 BASIC UNIT DETECTOR-GAS COMBUSTIBLE TRAK-IT IIIA BASIC UNIT DETECTOR-GAS SENSIT CO CARBON MONOXIDE ANALYZER

133 Safety Equipment Gloves Winter Tuf-Duk - Vinyl impregnated to provide an excellent grip and long wear. Sheds snow, sleet and rain (not liquid proof) available in medium size. Winter Monkey Grip - Liquid proof vinyl coating resists oil, acids, chemicals and caustics. Curved fingers, wing thumb, and general softness make this glove very comfortable and easy to wear. Foam insulation locks out cold, keeps hands warm. Deep fleece lining helps retains warmth, feels good on the hand. Winter Wet Monkey Grip - Raised surface means more gripping power, and safe handling of wet material. Tough vinyl coating protects non-woven lining to keep wetness on the outside, and warmth and dryness inside. Non-woven inner lining retains warmth, cushions for comfort, and is more flexible. LP M LP LP LP Carburetion Equipment Carburetors GLOVE-WINTER TUF-DK MED N/A WHEN GONE GLOVE-MONKEY GRIP KNIT WRIST FOAM INSULATED WINTER GLOVE-MONKEY GRIP SAFETY CUFF FOAM INSULATED GLOVE-MONKEY GRIP SAFETY CUFF WINTER WET Model 425 for Natural and LP Gas - The backbone carburetor for straight LP conversion, primarily designed for V-8 and large V-6 engines. Mixer for Dual Fuel or Straight LP comes with AC2-2 cam and silicone diaphragm. LP-CA425M-2 LP-AD LP-AV LP-CA300AM-50-2 LP-RK-300-MA-50 CARBURETOR-MIXER SIL DIAPH DIAPHRAGM-IDLE 425M SILICONE VALVE-425 SERIES CARBURETOR-MIXER ONLY NO AIR FILTER W/AC2-2 KIT-MAJOR REPAIR 133

134 Carburetion Equipment Converters - Beam, Cobra and Impco Model E Model E - The backbone of LP gas carburetion. The Model E rates at 350 HP maximum, standard 1/4" inlet, and 1" outlet. May order with orange or blue spring. The Very Best Ever Made. LP-EB-2 LP-RKE-2 CONVERTER-MODEL E KIT-REPAIR MODEL E Model L LP-LB-2 LP-RKL-2 CONVERTER-MODEL L N-H-SA 350 HP 1/4" INLET 1" OUTLET KIT-REPAIR MODEL L Model J Cobra Beam 60 LP-JB-2 CONVERTER-MODEL J 150HP 1/4" INLET 1/2" OUTLET LP-RKJ-2 KIT-REPAIR-MODEL J LP-COBRA CONVERTER-COBRA W/PRIMER LP-RK-COBRA KIT-REPAIR COBRA LP-60-A CONVERTER-BEAM 60HP LP-T60-RBK KIT-REBUILD T60 LP-T60-RK KIT-REPAIR BEAM T-60 Converter Mounting Brackets LP-GB-88 BRACKET-CONVERTER MOUNTING Manual Primer LP-AB1-28 MANUAL-PRIMER 134

135 Carburetion Equipment Vacuum Safety Switch LP-1501-L SWITCH ASSY-SAFETY MICROVAC Vacuum Filter Lockoff LP-VFF30-2 LP-RKVFF30-2 LP-F1-10 LOCK-OFF VACUUM W/FILTER REQUIRES 7/32" ID VAC HOSE KIT-REPAIR FOR VFF30-2 PAD-FILTER ONLY Electric Filter Lockoff FL V Lockoff Beam LP Gas - Mr. Dependable easy to maintain and rebuild. Will give you years of trouble-free service. Note: FL is a replacement filter kit. Engine Fuel Lockoff - The model ET98 with filter is an electrically operated safety shutoff valve suitable for high pressure up to 315 psi (21.72 bar) of LPG liquid, LPG vapor or natural gas vapor. It is a normally closed straight through lockoff, opened with 12V DC featuring an integrated filter. The filter model has two female NPT fittings and a mounting kit. LP-FL V LP-FL-4748 LP-ET LP-L-416 LOCK-OFF FILTER 12V W/FILTER KIT-FILTER FOR FL V VALVE-SOLENOID LOCK-OFF W/FILTER LOCK-OFF LP SOLENOID 1/4" 12V Gas Lockoff LP-GT-622 SOLENOID-6/12V DC GAS 1/8" W/GROUND COIL 135

136 Carburetion Equipment Senders and Receivers Sender and Receiver for Motor Fuel Service - Taylor s sender gives both direct and remote indication of LP gas liquid on all makes of cars and trucks when used with either a receiver or the original equipment fuel gauge on the vehicle. The sender also works on all recreational vehicles (RVs). LP-SQ-70 LP LP LP LP UNIT-SENDING OHM UNIT-SENDING 0-90 OHM SENDER OHM FORD 18' CABLE GAUGE-DUAL SITE SENSOR-RECEIVER MOTOR FUEL W/20' CABLE Fittings and Accessories Liquid Level Gauges MEJ606 is specifically designed for detecting tank liquid levels in remote filling applications where a standard fixed maximum liquid level gauge is not practical. Perfectly suited for motor fuel applications or other hard to reach tank applications. 1/4" MNPT x 1/4" M Flare. Single piece brass body. LP-MEJ606 GAUGE-LIQ LEVEL 90DEG 1/4" MPT X 1/4" ML FLR Removable thumb screw for serviceability. #54 orifice through hole

137 Carburetion Equipment Fittings and Accessories Fill Valve and Adpater ME229-EL 90 Angle allows connection of a motor fuel service line from 1-3/4 female Acme vapor outlet. Engine Fuel Remote Fill Valve - Specifically designed for remote filling applications where a standard tank type filler valve is not practical. Perfectly suited for motor fuel applications or other hard to reach remote tank applications. This single check fill valve is designed to provide maximum product fill rates along with an automatic shutoff once product flow ceases. Engine Fuel Remote Fill Valve Features Single check design allows maximum product flow rate Integral break away feature leaves check valve intact in the event of a vehicle roll away during filling Resilient bonded main valve seal Rear bulkhead mounting with quarter panel jam nut and lock washer Single piece main valve body for maximum strength and durability LP-ME229-EL LP-ME602-8 Remote Fill Assembly LP-RFB-2 ADAPTER-1-3/4" FML ACME BRASS 1/2" ML FLARE 90DEG VALVE-CHECK FILL 1-3/4" MLACME X 1/2" ML FLARE W/CAP & LANYD REMOTE-FILL ASSY 137

138 Carburetion Equipment Fittings and Accessories Bulkhead Fittings Engine Fuel Bulkheads - These bulkheads provide a stationary point for motor fuel lines to pass through sections of sheet metal. Economy Hydrostatic Relief Valve Features: Compact design to fit any application. 1/4" MNPT inlet to fit any domestic valve port or service port. Specially designed internal components to increase flow at discharge. 440 psig start-to-discharge. Non-adjustable, tamper resistant design. Protective vinyl cap included. Economically priced. ME Enables the installation of a 1/4" MNPT hydrostatic relief valve in a safe, protected area. This two-piece carburetion hose fitting fits all stainless steel braided LP gas hose with a 5/16" ID. The tank valve side has a 3/8" female flare swivel and zinc plated for maximum corrosion resistance. LP-MET443 LP-MET444 LP-MESTF33 LP-MEH225 LP-ME8346 Switches FITTING-BULKHEAD 3/8" M FLARE X 1/4" FNPT-2 PORT FITTING-BULKHEAD T 1/4" FPT X 3/4"-16 ML X 1-1/4" FNPT-2 PRT FITTING-BULKHEAD STRAIGHT 3/8" ML FLARE X 3/8" ML FLARE VALVE-RELIEF 1/4" MPT 440 PSI HYDROSTATIC BRASS NITRILE FITTING-HYDROSTATIC RELIEF LP-5592 LP-5586 Hose Fittings Straight SWITCH-3 WAY 6 POLE GAS & LP SWITCH-3-WAY ELEC GAS & LP LP-52SB FITTING-WATER HOSE BRASS LP-53SB NIPPLE-STRAIGHT 5/8" X 3/8" LP-54SB NIPPLE-STRAIGHT 5/8" X 1/2" LP-88SZ NIPPLE-STRAIGHT HOSE ZINC 138

139 Carburetion Equipment Hose Fittings Elbows LP-ME53EB LP-54EB LP-84EZ LP-86EZ LP-88EZ ELBOW-3/8" MPT X 5/8" HB BRASS 90DEG ELBOW-5/8" X 1/2" HOSE ELBOW-1" X 1/2" HOSE ELBOW-1" HB X 3/4" PIPE ZINC ELBOW-1" X 1" HOSE Clamps CLAMP-HOSE 1/2" SS CLAMP-HOSE 3/4" SS CLAMP-HOSE 1" SS CLAMP-HOSE 1-1/2" SS Reusable Couplings LP LP LP-6-4MP LP-6FS LP-6FS-45 LP-6FS-90 LP LP LP-1708 COUPLING-HOSE 3/16" ID CARB X 1/4" OD FML FLARE COUPLING-HOSE 3/16" ID CARB X 1/4" OD FML FLARE 90 DEG COUPLING-HOSE 5/16" ID CARB X 1/4" MPT COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE 45 DEG COUPLING-HOSE 5/16" ID CARB X 3/8" OD FML FLARE 90 DEG COUPLING-HOSE 13/32" ID CARB X 1/2" OD FML FLARE COUPLING-HOSE 13/32" ID CARB X 1/2" OD 90 DEG FML FLARE COUPLING-HOSE END 1/2" ID X 1/2" FML FL Miscellaneous LP-ME4231 FITTING-1/4" HB X 1/8" MPT BRASS 139

140 Carburetion Equipment Vapor and Engine Fuel Hose LP Gas Engine Fuel Hose LP Gas Engine Fuel Hose Construction: Specially compounded heat resistant synthetic rubber seamless inner tube, single braid of stainless steel wire. The hose is impregnated with oil and mildew resistant rubber compound. UL listed for LPG service. Application: Required for LP gas engine fuel lines. Temperature Rating: -40º to 257º F. Inner tube specially compounded to resist temperatures up to 257º F without cracking. LP-SS4-UL LP-SS6-UL LP-SS8-UL HOSE-SS BRAID CARB 3/16" 350 PSI HOSE-SS BRAID CARB 5/16" 350 PSI HOSE-SS BRAID CARB 13/32" 350 PSI Low Pressure Vapor Hose LP-VH-12 LP-VH-58 LP-VH-34 LP-VH-78 LP-VH-100 LP-VH-114 LP-VH112 Decals, Signs and Paint Decals and Signs 1075 Decal LP-G1075 LP-P1075 LP-V1075 HOSE-VAPOR CARB 1/2" LOW PRESSURE HOSE-VAPOR CARB 5/8" LOW PRESSURE HOSE-VAPOR CARB 3/4" LOW PRESSURE HOSE-VAPOR CARB 7/8" LOW PRESSURE HOSE-VAPOR CARB 1" LOW PRESSURE HOSE-VAPOR CARB 1-1/4" LOW PRESSURE HOSE-VAPOR CARB 1-1/2" LOW PRESSURE DECAL-MAGNETIC DIAMOND 1075 LP GAS BLACK/WHITE ON RED PLACARD-POLY DOT DIAMOND 1075 LP GAS DECAL-VINYL DOT DIAMOND 1075 BLACK/WHITE ON RED 2 PSI Decal LP-V62 DECAL-VINYL PROPANE GAS 2 PSI BLACK ON YELLOW 3/8" X 3" 140

141 Decals, Signs and Paint Decals and Signs Auto Decal LP-S500K DECAL-REFLECTIVE PROPANE DIAMOND WHITE ON BLK 4.5" X 3" LP-V109 DECAL-VINYL OPERATING UNDER 49CFR WHITE ON BLK 5.75" X 2.2 Cylinder Decal LP-A53 DECAL-VINYL LP CYL WARNING BLACK ON WHITE 5" X 1.5" LP-AA16 DECAL-VINYL DOT CYL RED/ BLACK ON WHITE 4" X 1.25" LP-CS33 DECAL-VINYL DOT CYL LABL WARN RED/BLK ON WHITE 5" X 1.5" LP-HZ116 DECAL-VINYL OSHA REQUIRED NFPA 4 COLRS ON WHITE 5"X2.25" LP-P101 DECAL-VINYL CYL CAPAPCITY CHART BLUE ON WHITE 12" X12.25 LP-P102 DECAL-VINYL NOTICE FOR YOUR RED/BLUE ON WHITE 12" X 12.25" LP-SP53R DECAL-VINYL REVISED NFPA CYL LABEL BLACK ON YELLOW 9" X 4" LP-V14 DECAL-VINYL CYL EXCG CHECKLIST RED/BLACK ON WHITE 12" X 16" LP-V121 DECAL-VINYL FILLING PROCEDURE PORT CYL RED ON WHITE 11" X 12 LP-V122 DECAL-VINYL ASME FILLING PROCED RED ON WHITE 11" X 12" LP-V123 DECAL-VINYL SAFETY IS YOU RED ON WHITE 11" X 12" LP-V128 DECAL-VINYL CAUTION NO OPD RED ON WHITE 3.75" X 4" LP-V206 DECAL-VINYL NPGA FILL PROCEDS RED ON WHITE 8" X 3.5" LP-V44R DECAL-VINYL 3 IN 1 PROPANE HAZ 4 COLORS ON WHITE 6.75" X 4.75 LP-V55R DECAL-VINYL 2 IN 1 CYL COLLAR RED/BLK ON WHTE 7.375" X LP-V56R DECAL-VINYL PROPANE HAZARD 4 COLORS ON WHITE 10" X 3.375" LP-V95 DECAL-VINYL VALVE IDENTIFY BLACK ON YELLOW 8.5" X 5.5" 141

142 Decals, Signs and Paint Decals and Signs DOT Inspection Decal LP-V31 DECAL-VINYL PERIODIC INSP KIT BLACK ON WHITE 18" X 6" LP-V66 DECAL-VINYL NQT RED ON WHITE 6.5" X 2.75" LP-V106 DECAL-VINYL NQT-HV TEST BLACK ON WHITE 10.25" X 6" LP-V107 DECAL-VINYL QT-WF TEST BLACK ON WHITE 10.25" X 6" Emergency Decal LP-V27 DECAL-VINYL FOR EMER CALL BLACK ON WHITE 1.15" X 3" LP-V45 DECAL-VINYL ID LABEL SET BULK TRUCKS RED ON WHITE 6" X 1" LP-V81 DECAL-VINYL EMER SHUTOFF PULL RED ON WHITE 10" X 12" LP-V82 DECAL-VINYL EMER SHUTOFF PUSH RED ON WHITE 10" X 12" LP-V127 DECAL-VINYL EMER SHUTOFF RED ON WHITE 30" X 12" LP-V129 DECAL-VINYL EMER SHUTOFF VALVE PUSH RED ON WHITE 5" X 6 LP-V134 DECAL-VINYL EMER SHUTOFF RED ON WHITE 6" X 2.5" LP-V148 DECAL-VINYL PULL SHUTOFF RED ON WHITE 12" X 12" LP-V149 DECAL-VINYL CONTAINER EMER PUSH TO CLSE RED/WHTE 12"X12" 142

143 Decals, Signs and Paint Decals and Signs Flammable Decal LP-V17A DECAL-VINYL FLAMMABLE GAS 6" LTRS RED ON WHITE 30" X 8" LP-V17B DECAL-VINYL FLAMMABLE GAS 4" LTRS RED ON WHITE 24" X 6" LP-V24A DECAL-VINYL FLAMMABLE 6" LTRS RED ON WHITE 28" X 7" LP-V24B DECAL-VINYL FLAMMABLE 4" LTRS RED ON WHITE 22" X 5" LP-V24BB DECAL-VINYL FLAMMABLE 3" LTRS RED ON WHITE 22" X 4" LP-V24C DECAL-VINYL FLAMMABLE 2" LTRS RED ON WHITE 14" X 3" LP-V48 DECAL-VINYL FLAMMABLE 8" LTRS RED ON WHITE 38" X 9" LP-V52 DECAL-VINYL DOT DIAMOND FLAMMABLE GAS WHITE ON RED #2 LP-V53 DECAL-VINYL DOT DIAMOND FLAMMABLE WHITE ON RED #3 Liquid and Vapor Decal LP-V90 DECAL-VINYL LIQUID LABEL RED ON WHITE 4" X 1" LP-V90-5 DECAL-VINYL LIQUID LABEL RED ON WHITE 4" X 1" 5/SHEET LP-V91 DECAL-VINYL VAPOR LABEL RED ON WHITE 4" X 1" LP-V91-5 DECAL-VINYL VAPOR LABEL RED ON WHITE 4" X 1" 5/SHEET 143

144 Decals, Signs and Paint Decals and Signs Liquefied Petroleum Gas Decal LP-V302BB DECAL-VINYL LIQUIFIED PETROGAS 3" LTRS RED ON WHITE 26" X 4" LP-V302C DECAL-VINYL LIQUIFIED PETROGAS 2" LTRS RED ON WHITE 24" X 3" No Smoking Decal LP-V23A DECAL-VINYL NO SMOKING 6" LTRS RED ON WHITE 27.5" X 6.75" LP-V23B DECAL-VINYL NO SMOKING 4" LTRS RED ON WHITE 27.25" X 6.75" LP-V23BB DECAL-VINYL NO SMOKING 3" LTRS RED ON WHITE 22" X 4" LP-V23C DECAL-VINYL NO SMOKING 2" LTRS RED ON WHITE 14" X 3" LP-V26A DECAL-VINYL NO SMOKING SHUTOFF MOTR 6" LTRS WHITE/RED 18"X12" LP-V26B DECAL-VINYL NO SMKNG OR OPN FLME 50' 4"LTRS RED/WTE 18X12" LP-V39B DECAL-VINYL NO SMKNG OR OPN FLME 25' 4"LTRS RED/WTE 18X12" LP-V49 DECAL-VINYL NO SMOKING 8" LTRS RED ON WHITE 42" X 10" 144

145 Decals, Signs and Paint Decals and Signs Propane Decal LP-V28A DECAL-VINYL PROPANE 6" LTRS RED ON WHITE 27.25" X 6.75" LP-V28B DECAL-VINYL PROPANE 4" LTRS RED ON WHITE 18" X 5" LP-V28BB DECAL-VINYL PROPANE 3" LTRS RED ON WHITE 14" X 4" LP-V28C DECAL-VINYL PROPANE 2" LTRS RED ON WHITE 12" X 3" LP-V47 DECAL-VINYL PROPANE 8" LTRS RED ON WHITE 38" X 9" LP-V58 DECAL-VINYL LPG MIN 90%/2% ORANGE/BLACK 3" X 2.5" N/A LP-V704-1 DECAL-VINYL STORAGE TANK DIAMOND 7.5" X 7.5" LP-V704-3 DECAL-VINYL STORAGE TANK DIAMOND 15" X 15" LP-V96 DECAL-VINYL PROPANE VERTICAL RED ON WHITE 8' VERT X 9" LTRS Railroad Crossing Decal LP-S22A LP-S22B DECAL-REFLECTIVE THIS VHLE STO RR XINGS 6"LTRS WTE/RED 36"X8" DECAL-REFLECTIVE WE STOP ATALL RR XINGS 4"LTRS RED/WTE 36"X4" Recertification Decal LP-C163 DECAL-VINYL REINSPECTION BLACK ON WHITE 3" X 1.875" 145

146 Decals, Signs and Paint Decals and Signs Signs LP-CG-126FO PLACARD-FOLDING 1075 & 1005 & BLANK LP-H PLACARD-HIGH PRESSURE GAS LINE POLY LP-M23BB SIGN-METAL NO SMOKING 3" LTRS RED ON WHITE 22" X 4" W/HOLES LP-M23C SIGN-METAL NO SMOKING 2" LTRS LP-M26B SIGN-METAL NO SMOKING 50' 4" LTRS RED ON WHITE 18" X 12" LP-M28C SIGN-METAL PROPANE 2" LETTERS LP-M39B SIGN-METAL NO SMOKING OR OPN FLME 4" LTRS RED/WHITE 18"X12" LP-M97A SIGN-METAL PROPANE FILLING 6" LTRS WHITE ON BLUE 1FACE 2'X4' LP-M97AX SIGN-METAL CYL EXCHANGE SINGLE FACED 4' X 2' LP-M97AXD SIGN-METAL PROPANE EXCHANGE WHITE ON BLUE 2FACE 2' X 4' LP-MPH69 PLACARD-HOLDER ALUM/WHITE LP-S35483 SIGN-METAL OPD REGULATIONS 18" X 24" LP-P1075 PLACARD-POLY DOT DIAMOND 1075 LP GAS LP-P111 SIGN-POLY CUST ALERT 20" X 16" RED/BLUE LP-P114 SIGN-POLY OPD RETROFIT CHART BLUE ON WHITE 18" X 24" LP-P81 SIGN-POLY EMER SHUTOFF PULL RED ON WHITE 10" X 12" LP-P82 SIGN-POLY EMER SHUTOFF PUSH RED ON WHITE 10" X 12" 146

147 Decals, Signs and Paint Klinger Paint and OverRust Paint - Gallon Cans Klinger Paint - Klinger s offer a full line of tank primers and coatings, aerosol cans, plus a line of accessories to meet your painting needs. Klinger s has been in the paint industry for over 100 years and offers premium quality products at fair prices. High performance tank coatings have a 5 year performance level with gloss retention. Bright white and light gray paint contain a mildew resistant additive. All tank coatings are available in a variety of colors in 12 oz. aerosol cans, 1 gallon cans or 5 gallon pails. Asphaltum, urethane tar and penetrol are also available. Tank Size Gallons Approximate Square Feet White Silicone White Enamel Light Gray Primer 30,000 2,000 7 Gallons 7 Gallons 7 Gallons 18,000 1,250 5 Gallons 5 Gallons 5 Gallons 12,000 1,160 4 Gallons 4 Gallons 4 Gallons 1, Gallon 1 Gallon 1 Gallon Tanks/Gallon 2 Tanks/Gallon 2 Tanks/Gallon Tanks/Gallon 5 Tanks/Gallon 5 Tanks/Gallon Square Foot Coverage Per Gallon of Paint* (1.0 Mil Dry) Recommended Dry Film Practical Spreading Rate 2.0 Mils Min. 325 sq. ft. 2.0 Mils Min. 330 sq. ft. 2.0 Mils Min. 340 sq. ft. Typical VOC *Square foot coverage varies because of difference in the solids content of each product required to obtain necessary dry film thickness. Surface protection is directly related to care in preparation before painting and the dry film thickness of coatings. A minimum of 4.5 mils (on smooth steel) on exterior of tanks is required. Excessive sweating of tanks and unusual damp environment requires greater film thickness to retard water and oxygen in the form of vapor from reaching the metal surface beneath. K130 K11017MR K11514 K11709 K18200 K18201 K18300 K18704 K18726 PAINT-KLINGER #130 TANK ALUMINUM GAL PAINT-KLINGER BRIGHT WHITE TANK ENAMEL MLDW RES GAL PAINT-KLINGER LIGHT GRAY TANK ENAMEL GAL PAINT-KLINGER LIGHT TAN TANK ENAMEL GAL PAINT-KLINGER RED TANK ENAMEL GAL PAINT-KLINGER YELLOW TANK ENAMEL GAL PAINT-KLINGER JOHN DEERE GREEN TANK ENAMEL GAL PAINT-KLINGER BLACK TANK ENAMEL GAL PAINT-KLINGER DARK BLUE TANK ENAMEL GAL 147

148 Decals, Signs and Paint Klinger Paint and OverRust Primer, Thinner, OverRust Easy to Use Safe (Water-Based) Destroys Existing Rust Coats and Protects Lasts for Years Proven Effective A One Step process applied directly on the Rust! No more sandblasting, grinding or sanding, simply brush, roll and spray directly over any rusted metal. OVER RUST is a unique two-step chemical process that stops rust dead in its tracks! It is the only effective way to totally eliminate destructive rust. Most conventional products and methods cannot compare with the overall performance of OVER RUST. There are no primer, paints, or rust treatments that can stop rust action once it has started as effectively, as easily and as inexpensively as OVER RUST! OVER RUST is applied directly onto the rust. Steel surfaces need only be clean of loose rust scales and simply power washed clean of oil and debris. Paint should be sanded back to ensure that OVER RUST comes in contact with the rust. That s it! When first applied, OVER RUST is tan in color, but, when it comes in contact with ferrous metal, an amazing chemical reaction takes place. This reaction phase causes OVER RUST to turn purple. Then, as it cures, it bonds to the metal and forms a tough, black polymer type coating that has actually permeated the rust and etched itself directly into the metal. This finished product is paint ready and guaranteed to offer you years of trouble free protection. K14022 PRIMER-KLINGER LIGHT GRAY EPOXY FAST DRY GAL K PRIMER-KLINGER LIGHT GRAY EPOXY FAST DRY 5 GAL K19900 THINNER-XYLOL GAL K THINNER-XYLOL 5 GAL 3501 OVER-RUST GAL RUST INHIBITIVE 148

149 Decals, Signs and Paint Klinger Paint and OverRust Paint - 5 Gallon Buckets Klinger Paint - Klinger s offer a full line of tank primers and coatings, aerosol cans, plus a line of accessories to meet your painting needs. Klinger s has been in the paint industry for over 100 years and offers premium quality products at fair prices. High performance tank coatings have a 5 year performance level with gloss retention. Bright white and light gray paint contain a mildew resistant additive. All tank coatings are available in a variety of colors in 12 oz. aerosol cans, 1 gallon cans or 5 gallon pails. Asphaltum, urethane tar and penetrol are also available. Tank Size Gallons Approximate Square White Silicone White Enamel Light Gray Primer Feet 30,000 2,000 7 Gallons 7 Gallons 7 Gallons 18,000 1,250 5 Gallons 5 Gallons 5 Gallons 12,000 1,160 4 Gallons 4 Gallons 4 Gallons 1, Gallon 1 Gallon 1 Gallon Tanks/Gallon 2 Tanks/Gallon 2 Tanks/Gallon Tanks/Gallon 5 Tanks/Gallon 5 Tanks/Gallon Square Foot Coverage Per Gallon of Paint* (1.0 Mil Dry) Recommended Dry Film Practical Spreading Rate 2.0 Mils Min. 325 sq. ft. 2.0 Mils Min. 330 sq. ft. 2.0 Mils Min. 340 sq. ft. Typical VOC *Square foot coverage varies because of difference in the solids content of each product required to obtain necessary dry film thickness. Surface protection is directly related to care in preparation before painting and the dry film thickness of coatings. A minimum of 4.5 mils (on smooth steel) on exterior of tanks is required. Excessive sweating of tanks and unusual damp environment requires greater film thickness to retard water and oxygen in the form of vapor from reaching the metal surface beneath. K11017MR-5 PAINT-KLINGER BRIGHT WHITE TANK ENAMEL MLDW RES 5 GAL K PAINT-KLINGER LIGHT TAN TANK ENAMEL 5 GAL 149

150 Decals, Signs and Paint Klinger Paint and OverRust Paint - Spray Cans K11002SP PAINT-KLINGER #2 TAN SPRAY CAN MIN OF 12 K11017MRSC PAINT-KLINGER WHITE SPRAY CAN MIN 12 K18200-PGGSC PAINT-KLINGER RED SPRAY CAN PENDLETON GRAIN GROWERS K18200SC PAINT-KLINGER RED SPRAY CAN MIN 12 K18704SC PAINT-KLINGER BLACK SPRAY CAN MIN 12 K18729SC PAINT-KLINGER FERGUSON GRAY IND ENAMEL SPRAY CAN MIN 12 Underground Coatings K1888 K18900 ASPHALTUM-BLACK ECONY UNDRGND COATING TAR-MS URETHANE KLINGER PREM UNDRGND COATING GAL 150

151 Vaporizers and Parts Vaporizers Direct Fired Algas 40/40H These direct fired vaporizers convert liquid LP gas to vapor (gas) for the distribution system or a mixer. These small to large capacity units are used on a wide variety of applications such as crop drying, space heating, incineration, and commercial baking. Applications where fuel service cannot be interrupted, the vaporizers (in conjunction with a mixer) operate in a standby system to provide uninterrupted fuel flow and continued peak capacity. Uniform Gas Supply The direct fired vaporizers supply a steady gas supply over a broad temperature range. The units offer quick reaction to changes in flow and have easily accessible operational controls. Installation Ease As little as 1.5 square feet is needed to install these self-contained vaporizers, enabling the units to be placed where space is limited. There are only two connections to be made, a liquid inlet line and vapor outlet line with no complicated leveling. Sturdy Construction All weather construction of baked enamel finish on both the inside and outside of the cabinet gives maximum durability and resistance to the elements and eliminates the need for a shelter. Versatile Modular construction allows additional vaporizers to be added to the system as the gas demand grows. Costly change-outs are not required. Increased Safety Both models have overload and double anti-flood protection. LP-40/40H Algas 80/40H LP-80/40H Algas 120/60H LP-120/60H VAPORIZER-DIRECT FIRED 40 GPH ALGAS/SDI VAPORIZER-DIRECT FIRED 80 GPH ALGAS/SDI VAPORIZER-DIRECT FIRED 120 GPH 151

152 Vaporizers and Parts Vaporizers Direct Fired Ransome RH Series RH Series Direct-Fired LP Gas Vaporizers Standard Features: Mechanical liquid inlet valve provides positive control of LP gas liquid level on all RH 50, 80 and RH 120 sizes. Larger sizes use reliable float switch and electric inlet valve to prevent liquid carryover. Millivolt-powered gas control system maintains consistent vapor temperature under changing load conditions. Gas control valve is located inside the protective dry cabinet with the regulator mounted on the exterior providing for total ventilation. Precision operating temperature switch, factory-set and sealed against tampering, incorporates precious metal contacts for extended service life. Two-stage pressure regulation provides accurate gas burner pressures and performance regardless of changes in inlet pressure. ASME code vaporizing tubes with integral heat exchange vanes and insulated ducts provide efficient vaporization with minimum burner input. Modular design provides maximum capacity in a compact, rectangular unit. Double louvered combustion air baffles assure freedom from outages even during adverse weather conditions. (For extreme conditions, optional electric pilot re-ignitors are available). All sizes are capable of infinite turndown and will maintain a ready supply of vapor from zero load to full capacity. At no load, only enough heat will be generated to maintain vapor temperature and to prevent condensation. LP-RH50E LP-RH200E LP-RH400E LP-RH800E LP-RH1000 VAPORIZER-RANSOME E OPTION 50 GPH VAPORIZER-RANSOME E OPTION 200GPH VAPORIZER-RANSOME E OPTION 400GPH VAPORIZER-RANSOME E OPTION 120V 800GPH VAPORIZER-RANSOME 1000 GPH 152

153 Vaporizers and Parts Vaporizers Direct Fired Ransome RH Series 153

154 Vaporizers and Parts Vaporizers Electric Algas Zimmer LP-Z40P-UL/CE-V1J VAPORIZER-ZIMMER LP KIT-MOUNTING HORIZONTAL TANK UP TO 48" DIA LP KIT-PIPING ZIMMER TO USE WITH Algas Torrexx Standard Features: Proprietary Liqui-SAFE Valve positively prevents liquid carry over and provides visual indication when tripped. Greater reliability through simplified and more robust controls, no start/stop switches. Heavy duty 135 amp contactor increases life span of contactor and reduces maintenance. Replaceable temperature controller with an adjustable set point. Thermocouple temperature sensor increases life and reduces maintenance. Modular control board with easily replaceable components. Withstands momentary power interruptions without service disruption. Hazardous area classification: Class I, Division 1 and Zone 1. Dry electric design requires no water or glycol. 98% thermal efficiency. Operates on any LPG mixture from 100% propane to 100% butane. Perfect for any climate, rated to -40º F. Ready for operation in less than one minute. Automatic restart standard on all units. Optional economy operation pressure activated valve allows vaporizer use only when needed. The valve can be field installed on any unit up to 160 GPH and no additional electricity is required. LP-TX25 LP-TX50 LP-TX100 LP-TX160 LP-TX240 LP-TX320 VAPORIZER-TORREXX ELEC 12.5 GPH BASE UNIT VAPORIZER-TORREXX ELEC 25 GPH BASE UNIT VAPORIZER-TORREXX ELEC 50 GPH BASE UNIT VAPORIZER-TORREXX ELEC 80 GPH BASE UNIT VAPORIZER-TORREXX ELEC 120 GPH BASE UNIT VAPORIZER-TORREXX ELEC 160 GPH BASE UNIT 154

155 Vaporizers and Parts Vaporizers Electric Algas Torrexx 155

156 Vaporizers and Parts Tank Heater Algas Second Sun The SECOND SUN is a flameless, gas powered, catalytic tank heater that is designed to safely augment natural vaporization from the tank at times when the environment is not able to supply the energy needed through the wetted surface of the LPG tank. The units operate based on tank pressure. The operating control is a pressure switch that monitors the pressure in the tank and activates the main heater on and off according to the pressure in the tank. The operating pressure switch is factory set at 55 psi and can be manually adjusted in the field if needed. When pressure in the storage tank falls below the operating switch set point, the heater will cycle on providing heat (energy) into the liquid stored in the tank. When the pressure requirement is satisfied, the tank heater reverts to standby mode. SECOND SUNconsists of a staged heater, a small portion called the pilot heater and a larger portion called the main heater. The pilot heater is used to start the catalyzing process with a limited energy source. An integral 12V DC heater is used to initially start SECOND SUN. After start-up, the tank heater is self-contained and requires no electricity for operation. SECOND SUN is equipped with safety controls for high pressure and high temperature and utilizes propane vapor from the storage tank for operation of the heater and safety controls. Since SECOND SUN does not have a pilot flame nor is it a source of ignition, the unit meets requirements for installation in hazardous locations. SECOND SUN provides low temperature radiant heat that will not overheat or harm the tank s surface. The unit is versatile and designed to be installed on various tank sizes depending on the model. It is simple to install and easy to remove for annual tank and heater inspection. SECOND SUNcan be used with propane, butane or LPG mixtures. LP-SS-30 HEATER-SECOND SUN 30K BTU 156

157 Vaporizers and Parts Oil Separator The FAB-5 oil separator removes heavy ends from gas vapor streams and is especially effective after vaporizers. This single stage model provides primary extraction of heavy end particles and solid material in a gas vapor stream by centrifugal action in the chamber. The FAB-5 features all welded construction and is designed to be installed in a controlled pressure pipeline, 100 psig or less. It is self-cleaning and prime coat painted. Available in vertical configuration only. LP-FAB-5 SEPARATOR-OIL STYLE A 157