Spring Brake Application
|
|
- James Tyler Chapman
- 5 years ago
- Views:
Transcription
1 Technical Tip Maxibrake I Series Spring Brakes Disassembly, Inspections and Reconditioning Instructions Maxibrake I Series spring brake products are mechanical devices and are subject to wear after extended use. Periodic inspection and service is required to assure satisfactory service. Haldex recommends inspection intervals as follows: Minor Brake Inspection 1 Year or 40,000 miles [whichever occurs first] Perform pneumatic leak test - service brake Perform pneumatic leak test - park brake Inspect pushrod boot for cuts/cracks Inspect chamber vent holes [clear contamination as necessary] Major Brake Inspection 3 Years or 120,000 miles [whichever occurs first] Install piston repair kit # RN21AL Replace service brake diaphragm (included with kit) Replace pushrod boot assembly (included with kit) Maxibrake I Series Spring Brake Operation The operating principle is sound and simple. The service chamber applies the foundation brake with the application of air pressure. The power spring, normally held-off with air pressure, applies the brake mechanically when the air pressure is removed. Normal Driving Spring Brake Application Service Brake Application WARNING - Spring brake chambers contain a spring with high force. Disassembly and maintenance should only be performed in full accordance with manufacturer s written instructions. CAUTION - Always block wheels to prevent vehicle from moving when deactivating the air brake system.
2 Technical Tip 1. Disassembly and re-assembly can be easily and safely accomplished using a shop press or the Maxitool ( ) shown in Fig.1 and a bracket ( ). Drawings are available upon request. Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig Mounting the unit on the bracket and securing with mounting nuts will facilitate disassembly with the Maxitool. Fig Mark location of service inlet port on clamp band with respect to the spring chamber so that the unit can be re-assembled to the original configuration. Fig Loosen clamp band nuts and bolts and remove clamp bands. Fig Remove the pressure housing and diaphragm. Fig Break the jam nut loose from the flange nut. Fig. 6. Fig. 7 Fig.8 Fig. 9 Fig Press in on the pushrod plate to relieve return spring force. Remove jam nut and flange nut from pushrod. Fig Pull out pushrod, return spring and spring retainer. Fig Free the pushrod bushing from the piston by inserting the Maxitool shaft or pushrod through the piston tube and tapping lightly. Remove and discard the plastic bushing. Fig Place the unit on a bench with the mounting studs facing up. Apply 100 psi to the emergency port and spray soapy water inside the piston tube. Inspect for bubbles at bottom of tube where the stainless steel tube meets the aluminum piston casting. If the joint between the piston tube and casting is leaking, replacement of the unit is recommended. Fig. 10
3 Technical Tip 11. Place unit in shop press capable of 4,000 pounds force and 8 inches of travel. Use safe shop practices to assure fixturing holds the actuator securely. Fig. 11 Fig. 11 Fig. 12 Fig. 13 Fig If a shop press isn t available, insert the Maxitool from the service side of the unit through the piston tube until the round plate and locater contacts the spring support. Fig Assemble machined locator bushing on Maxitool with the small diameter toward piston tube. Screw nut on the Maxitool shaft and tighten against the machined locator. Fig Tighten nut until the Maxitool is centered and resting firmly against the spring support then tighten the nut three full turns fully releasing the spring pressure. (Spring does not need to be fully compressed) If using a shop press, bring ram down against the spring support and apply only enough pre-load to relieve spring pressure on the cap screws. Fig Remove the eight (8) cap screws holding the spring support. Fig. 15 Fig. 15 Fig. 16 Fig. 17 Fig Raise the press or gradually back off the nut on the Maxitool until all pressure is off of the spring. Fig Remove the Maxitool, power spring and spring support. Fig Remove the piston assembly from the cylinder being careful not to damage the end of the tube. Fig. 18
4 Technical Tip Disassembly Continued 19. Remove and discard the felt wiper and O-Ring from the piston. Take care to avoid damaging the piston groove surfaces with any tool used to remove the O-ring. Fig. 19 Fig. 19 Fig Remove the O-Ring and nylon bushing from the cylinder center boss. Use a sharp pointed instrument to remove the bushing; work clockwise from the cut to pry the bushing out of the groove. Fig Wash all of the metal parts in cleaning solvent. Fig. 21 Fig. 21 Inspection & Reconditioning Cylinder Assembly Check the bore for rust, scoring, loose coating or dents. Missing paint is not a problem as long as the cylinder bore is not rusty. Scuffs or light scratches in the coating can be smoothed with a fine emery cloth or steel wool. Also check for and remove any burrs around the cap screw holes that might cut the O-Ring during re-assembly. Make sure the mounting studs are not bent and the threads are not damaged. Assure surface is smooth with no defects that will lead to accelerated wear. Piston Assembly Check for and remove all nicks, burrs and scratches from the piston skirt and grooves. The piston tube is stainless steel and should be free of scratches. Proper care of the piston tube is important to assure reliable performance. The rubber dust boot is very effective to keep the piston tube clean during use. Piston assemblies can be replaced if damaged. See Service Part List. Power Spring Replace the power spring if evidence of corrosion or peeling paint is found. See Service Part List.
5 Technical Tip Re-assembly Fig. 1 Fig. 2 Fig. 3 Fig Install nylon bushing in the outer most groove of the boss on end of cylinder. NOTE: Bushing must be installed so the side with the beveled edge on the inside diameter faces toward the inside of the cylinder. Lubricate and install small O-Ring in the inner groove. Fig 1 & Fig. 2 2.Install the oil soaked felt wiper in the groove next to the open end of the piston. Fig Lubricate and install large O-Ring in the pre-lubricated center groove of the piston assembly. Fig Grease the inside of the cylinder with a thin even coat of the lubricant provided (M ). Fig Insert piston assembly in cylinder, holding felt wiper in place as piston is inserted. Fig Push the piston assembly all the way in, taking care to not cut or damage the small O-Ring with the end of piston tube when inserted. Also take care that the large O-Ring is not damaged as it passes by the cap screw holes in the cylinder. Fig Assemble spring support and power spring using a shop press or the Maxitool. If using Maxitool, insert through piston assembly. Run the Maxitool guide bushing and nut on the shaft and tighten slowly. Take care to center the spring with the piston hub and spring support. Fig. 7 Fig. 5 Fig. 6 Fig. 7 Fig Tighten nut down (or run down in shop press) until holes in the spring support align with the holes in the cylinder. Install the eight (8) cap screws securing the spring support to the cylinder. Fig. 8
6 Technical Tip 9. Alternately tighten the screws to 125 in-lbs of torque. Fig. 9 Fig. 9 Fig. 10 Fig. 11 Fig Remove the Maxitool or remove the unit from the shop press. Install the pushrod bushing into the piston. Tap lightly and make sure the bushing is inserted properly. Fig Assemble spring retainer (cupped side against pushrod plate) and pushrod return spring on the pushrod; install the rod through bushing and piston tube. Secure loosely with the flange nut. Fig Install diaphragm with the crowned surface in the pressure housing and center over the cylinder. Align the port boss on the pressure housing according to the marks put on in disassembly step 3, and apply pressure to the housing to squeeze the diaphragm. Align clampband assembly with the pressure housing and cylinder flanges. Fig Tighten the nuts to between 120 and 180 inlbs of torque. Make sure the bolts are evenly tightened on both sides. Fig. 13 Fig. 13 Fig. 14 Fig. 17 Fig Apply shop air pressure between 95 and 105 psig to the spring chamber so that the spring is fully compressed and the piston tube is approximately flush with the cylinder boss. Fig Adjust the flange nut on the pushrod until there is a 1/16 to 1/8 clearance gap between the piston tube and the flange nut. FIg If a scale is not available, a U.S. quarter may be used to gage the distance between the flange nut and piston tube. Fig. 16
7 Technical Tip Re-assembly Continued 17. Secure in position with the jam nut. Test both chambers for air leaks. Fig.17 Fig Install all 4 vent plugs in cylinder. Note: Bottom most plug must be removed upon installation. 19. Install reinforcement tube according to Maxibrake I Spring Brake Reinforcement Tube Install Instructions (L55288W) on the Web. 20. Install boot on the pushrod. Service Kit Part Number RN21AL contains all of the service items to recondition two (2) Maxibrake units; two (2) complete sets of O-Rings, oil soaked felt wipers, pushrod bushings, piston tube bushings and a special lubricant formulated exclusively for the Maxibrake spring brake. Contents of Service Kit (RN21AL) Description Quantity Part Number O-Ring SMall 2 M O-Ring Larger 2 M Felt Wiper 2 M Nylon Bushing 2 M Pushrod Bushing 2 M Lubricant (3 oz. tube) 1 M Vent Plug 8 M Diaphram (type 30) 2 DP30 Boot Assembly 2 M
8 Technical Tip Item Description Type 20 Type 24 Type 30 Type 36 1 Pressure Housing Assembly (1) M M M M Clampband Assembly M M M M Diaphragm DP20 DP24L DP30* DP36 4 Pushrod Assembly -J = 8.00 M102560BB M102580DB M102732AC M14096DB 5 Return Spring Retainer M Return Spring M M Pushrod Bushing (2) M Spring Support M M Power Spring - #50 M Power Spring - #60 M Power Spring - #75 M Felt Wiper (2) M O-Ring - Large (2) M Piston Assembly M M M Vent Plug M Cap Screw M M Cylinder Assembly (1) M M M M O-Ring - Small (2) M Nylon Bushing M Flange Nut (5/8-18UNF) M Jam Nut (5/8-18UNF) HW5 20 Dust Boot Kit M * (1) Pressure Housing Assemblies come with a single 3/8 NPTF side inlet port. Cylinder Assemblies come with a single 3/8 NPTF inlet port oriented 90 from the mounting studs. (2)These items are included in the Service Kits, RN21AD (for repair of a single Maxibrake unit) RN21AE (for repair of two Maxibrake units) RN21AL (for repair of two transit bus units) *Included with kit RN21AL
INSPECTION & MAINTENANCE BULLETIN ARI 1301/1302 1" Plug Type Angle Valves
INSPECTION & MAINTENANCE BULLETIN ARI 1301/1302 1" Plug Type Angle Valves Item # Description Item # Description 1 Body 12 Washer 2 Packing Retainer 13 Bushing 3 Packet Set 14 Bolt 4 Jam Nut 15 Yoke 5 Stud
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More informationINSPECTION & MAINTENANCE BULLETIN ARI Plug Type Angle Valves
INSPECTION & MAINTENANCE BULLETIN ARI 1316 2 Plug Type Angle Valves Item # Description Item # Description Item # Description 1 Body 12 Top Stem Nut 23 Seat Gasket 2 Valve Disc 13 Handwheel 24 Valve Seat
More informationMaintenance Information
16573370 Edition 2 February 2014 Air Grinder 99V Series Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationMaintenance & Repair Manual
SM64055 November 2012 Aerospace Group Conveyance Systems Division Applicable additional manuals: None Carter Brand Ground Fueling Equipment Maintenance & Repair Manual 4 Inch Internal/Bottom Loading Valves
More informationMaintenance Manual. 3-Inch Internal Valve. F660 Series
3-Inch Internal Valve F660 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page.
More informationModel INTERNAL/BOTTOM LOADING VALVES SM Maintenance & Repair Manual. July Applicable addition manuals: None
SM64128 July 2010 Eaton Aerospace Group Conveyance Systems Division Carter Brand Ground Fueling Equipment Applicable addition manuals: None Maintenance & Repair Manual 6 INTERNAL/BOTTOM LOADING VALVES
More informationMaintenance Manual 3-INCH INTERNAL VALVE F660 SERIES
Maintenance Manual 3-INCH INTERNAL VALVE F660 SERIES REVISION 1.1 03/15/2002 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical
More informationFOR FUTURE REFERENCE SERIES 93HPS
Hypro Series 93HPS Hydraulically Driven Wetseal Multistage Pumps Repair Manual KEEP FOR FUTURE REFERENCE Form L-1578R Rev. A SERIES 93HPS Hydraulically Driven Stainless Steel Multistage Centrifugal Pumps
More informationMETERING VALVE 2" STEM GUIDED
2" STEM GUIDED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be construed
More informationINTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco
Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their
More information2. Disconnect negative battery cable to avoid possible fuel discharge if an accidental attempt is made to start the engines.
PART #25001 LT1 Adjustable Fuel Pressure Regulator, 1994-1997 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER DESCRIPTION
More informationDura Force Disc Brake System Service Manual
TS 20809_a 3501 Shotwell Drive ISO/TS 16949:2002 Registered (PH): 937.743.8125 Franklin, OH 45005 www.waltheremc.com (FX): 937.743.8232 Table of Contents General Description 1 3 Fastener Torque Chart 4
More informationSECONDARY SERVICE EXTERIOR R-12DC VALVE (MODEL WITH 4 VERTICAL DELIVERY PORTS) DELIVERY COVER SECONDARY RELAY PISTON VALVE RETAINER INLET EXHAUST
SD-03-1068 Bendix R-12DC Relay Valve with Biased Double Check PRIMARY SECONDARY EXTERIOR R-12DC (MODEL WITH 4 VERTICAL DELIVERY PORTS) SUPPLY (2) EXTERIOR R-12DC (MODEL WITH 2 HORIZONTAL PORTS) DELIVERY
More informationSD Bendix DD-3 & SD-3 Safety Actuators PUSH PLATE & SHAFT ASSY. LOCKPORT SERVICE DIAPHRAGM SEPARATOR LOCKING PISTON O-RING LOCKING PISTON
SD-02-4600 Bendix DD-3 & SD-3 Safety Actuators AUXILIARY DIAPHRAGM SERVICE DIAPHRAGM SEPARATOR PUSH PLATE & SHAFT ASSY. LOCKING PISTON O-RING LOCKING PISTON LOCKPORT DRAIN SLOT RETURN SPRING CAP O-RING
More informationMGM Brakes Service Manual
MGM Brakes Service Manual MAGNUM Performance Plus Spring Brake Actuators (MJ-Series 3.00 / 76mm Long Stroke ) For: S-Cam Tamper-Resistant MAGNUM Performance Plus Spring Brake Actuators Figure 1 A B C Your
More information2002 F-Super Duty /Excursion Workshop Manual
Page 1 of 25 SECTION 307-01: Automatic Transaxle/Transmission 2002 F-Super Duty 250-550/Excursion Workshop Manual ASSEMBLY Procedure revision date: 05/23/2001 Transmission Special Tool(s) Remover, O-Ring
More informationSD Bendix E-12 & E-15 Dual Brake Valve DESCRIPTION
SD-03-6 Bendix E- & E-15 Dual Brake Valve TREADLE UPPER BODY ASSEMBLY PRIMARY DELIVERY ( ) 1 SECONDARY DELIVERY ( ) LOWER BODY ASSEMBLY MOUNTING PLATE PRIMARY SUPPLY ( SUP-1) PRIMARY SUPPLY ( SUP-) PRIMARY
More informationLOW PRESSURE BALANCED VALVE DIAPHRAGM BALANCED
DIAPHRAGM BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to
More informationOperation and Maintenance Instructions for Bettis GVO-C Series GVO-CLP-SR Pneumatic Actuators
Part Number: GVO-CLP-SR.IOM.1003, Rev. 0 Release: March 2016 Operation and Maintenance Instructions for Bettis GVO-C Series GVO-CLP-SR Pneumatic Actuators Part Number: GVO-CLP-SR.IOM.1003, Rev. 0 Table
More information2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 5.- PERIODICAL INSPECTION OF THE VALVE AND MAINTENANCE
Page 1 of 16 CONTENTS 1.- INTRODUCTION 2.- HANDLING OF VALVES BEFORE ASSEMBLY 3.- FITTING THE VALVE TO THE REST OF THE ASSEMBLY 4.- OPERATION OF A BALL VALVE 5.- PERIODICAL INSPECTION OF THE VALVE AND
More informationFig Variable Speed Valve Parts
5 DISASSEMBLY OF VARIABLE SPEED CONTROL VALVE (Seal Replacement with Control Valve in the Bobcat). Remove seat and seat plate (Fig. ).. Remove variable speed control lever linkage rod. 3. Remove temperature
More informationPOWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires
More informationCLEANING, INSPECTION AND REPAIR. Valve Spring Compressor (Part No. HD-34736B) Figure Compressing Valve Springs
b0134x3x 5694 8 7 12 10 1 6 13 11 Valve Spring Compressor (Part No. HD-34736B) 9 Figure 3-11. Compressing Valve Springs 5 14 4 3 2 15 2767a 1. Right crankcase half 2. Pin (2) 3. O-ring (2) 4. Plate 5.
More informationMaintenance Manual 6-INCH INTERNAL VALVE F620 SERIES
Maintenance Manual 6-INCH INTERNAL VALVE F620 SERIES REVISION 1.1 03/15/2002 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical
More informationHIGH PRESSURE CONTROL VALVE PISTON BALANCED
PISTON BALANCED All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been made to ensure their accuracy, they are not to be
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts
More informationDisassembly and Reassembly for CBB (Double Acting) Series Pneumatic Actuators
MECATORK S.A.S Release: May 2012 Disassembly and Reassembly for CBB (Double Acting) Series Pneumatic Actuators MECATORK S.A.S Table of Contents May 2012 Table of Contents Section 1: Introduction 1.1 General
More informationPOWER BRAKES-MORAINE
5-30 1955 PONTIAC SHOP MANUAL SERVICE CRAFTSMAN NEWS REFERENCE News News Page Year No. No. Subject POWER BRAKES-MORAINE GENERAL DESCRIPTION The Moraine Power brake unit can be identified by the cast iron
More informationBRAKES. Section III REAR AXLE DATA AND SPECIFICATIONS HAND BRAKE CHRYSLER SERVICE MANUAL BRAKES 17
BRAKES 17 There is no basic design change in the rear axle and sure grip differential except the larger diameter pinion shaft is now used on all models for 1959. The Service Procedures will remain the
More informationOperation & Maintenance Manual 4900 Series Pipeline Injection Pumps Bulletin 150
340 West Benson Avenue Grantsburg, WI 54840 1-800-366-1410 715-463-5177 www.northern-pump.com Table of Contents Introduction... 3 Rotation... 4 Hydraulic Balance... 5 Cautionary Statements... 6 Pump Installation...
More informationCYLINDER HEAD OVERHAUL
ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION -2011 Mercedes-... Page 1 of 20 CYLINDER HEAD OVERHAUL * PLEASE READ THIS FIRST * Examples used in this article are general in nature and do not necessarily
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More informationCARTER DOWNDRAFT CARBURETOR Terraplane All Models. Technical Information
CARTER DOWNDRAFT CARBURETOR 1934 Terraplane All Models Technical Information . Carter W-1 Downdraft Carburetors 1934 Terraplane Challenger, Model KS NOTE: Terraplane Models. Carburetor fitted with Anti-
More informationMGM Brakes Service Manual
MGM Brakes Service Manual MODEL LTR-T - 2.50 Pre 6/1/98 MODEL LTR-T - 2.50 Post 5/31/98 MODEL LTR-L3-3.00 For: Long Life Integral Release Bolt Double Diaphragm Spring Brakes Several design improvements
More informationTBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE. For technical questions, please contact the following:
TBV OPERATION AND MAINTENANCE MANUAL SERIES 1800: FLANGED BALL VALVE For technical questions, please contact the following: Engineering Department 1537 Grafton Road Millbury, MA 01527 Phone: (508) 887-9400
More informationDIFFERENTIAL PRESSURE RELIEF REGULATOR TYPE A4AL Port Size 3/4"- 4" (20-100mm) For Ammonia, R-22, R134a, R404a, R507 and other common refrigerants.
DIFFERENTIAL PRESSURE RELIEF REGULATOR TYPE A4AL Port Size 3/4"- 4" (20-100mm) For Ammonia, R-22, R134a, R404a, R507 and other common refrigerants. FEATURES Pilot operated characterized Modulating Plug
More informationNOTE: Visit our website at for video repair procedures, under the Tools section.
Repair Instructions Hypro Repair Tools: Tool Box No. 3010-0168 1/4" Allen Wrench No. 3020-0008 Support Bars (2) No. 3010-0064 Port Brush No. 3010-0066 1/16" Allen Wrench No. 3020-0009 Brush Holder No.
More informationSD Bendix R-6 Relay Valve DESCRIPTION OPERATION
SD-03-1060 Bendix R-6 Relay Valve SUPPLY PORT (RESERVOIR MOUNT TYPE) SERVICE PORT RETURN SPRING RELAY PISTON DELIVERY PORTS (4) SUPPLY PORT EXHAUST R-6 RELAY VALVE INSERT FIGURE 1 FIGURE 2 DESCRIPTION
More informationHub Installation and Bearing Adjustment. Hub Installation and Bearing Adjustment. Hub Preparation Prior to Installation
Hub Installation and Bearing Adjustment Hub Installation and Bearing Adjustment Scope: This service procedure is intended to provide general instructions for reinstallation of a hub onto an axle after
More informationMaintenance Information
16573347 Edition 2 February 2014 Air Grinder Series 88H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More informationOperation & Maintenance Manual For 4900 Series Pumps Bulletin 134
For 340 West Benson Avenue Grantsburg, WI 54840 1-800-366-1410 715-463-5177 www.northern-pump.com Table of Contents Introduction... 3 Cautionary Statements... 5 Pump Installation... 6 Removal from Installation...
More informationDESCRIPTION FUEL AND VACUUM PUMP REMOVE AND REPLACE FUEL PUMP-OVERHAUL 6B PONTIAC SHOP MANUAL. S. Install battery and connect cables.
6B-74 1955 PONTIAC SHOP MANUAL DESCRIPTION FUEL AND VACUUM PUMP All models are equipped with a combination fueland double acting vacuum pump operated by an eccentric bolted to the front end of the engine
More informationIndustrial Turbo Meters, Sizes 2" through 6"
Industrial Turbo Meters Sizes 2" through 6" TUR-UM-00530-EN-19 (October 2014) User Manual Industrial Turbo Meters, Sizes 2" through 6" User Manual CONTENTS Scope of the Manual 5 Specifications 5 Product
More informationSD Bendix E-10PR Retarder Control Brake Valve DESCRIPTION. OPERATION - Refer to Figure 2
SD-03-832 Bendix E-10PR Retarder Control Brake Valve MOUNTING PLATE SUPPLY 4 PORTS ELECTRICAL AUXILIARY DESCRIPTION TREADLE RETARDER CONTROL SECTION EXHAUST DELIVERY 4 PORTS FIGURE 1 - E-10PR RETARDER
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationINSTALLATION/OPERATION/MAINTENANCE MANUAL for the FlowMax REGULATOR
INSTALLATION/OPERATION/MAINTENANCE MANUAL for the FlowMax REGULATOR SCOPE This manual provides instructions for the Installation, Operation, and Maintenance of the FlowMax Regulator (instructions for the
More informationThese instructions are applicable to the following models: ARI 1118 ARI 1148
INSPECTION & MAINTENANCE BULLETIN ARI 1118 & 1148 Safety Relief Valve These instructions are applicable to the following models: ARI 1118 ARI 1148 Only AAR class F facilities are certified to recondition,
More informationTECHNICAL BULLETIN. TP Issued Servicing Rockwell s TB Series Trailer Axles with Unitized Hub Assemblies
TECHNICAL BULLETIN TP-96175 Issued 12-96 Servicing Rockwell s TB Series Trailer Axles with Unitized Hub Assemblies TB Series Trailer Axles Introduction Rockwell s TB series trailer axle features a permanently
More informationMaintenance Manual. 4-Inch Internal Valve. F614 Series
4-Inch Internal Valve F614 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page.
More informationABI WHEEL & BRAKE KIT
INSTALLATION INSTRUCTIONS and INSTRUCTIONS FOR CONTINUED AIRWORTHINESS for the installation of ABI-199-62 WHEEL & BRAKE KIT for CESSNA AIRCRAFT SERIES 180, 185, 206 Doc No.: ABI-199-62-4 REV B 04/21/2017
More informationThese instructions are applicable to the following models: ARI 1108 ARI HP1108
INSPECTION & MAINTENANCE BULLETIN ARI 1108 & HP1108 Safety Relief Valve These instructions are applicable to the following models: ARI 1108 ARI HP1108 Only AAR class F facilities are certified to recondition,
More informationBray/ VAAS Slurry Series Knife Gate Valve 760/762/765/766/767/768 Series Operation and Maintenance Manual
Bray/ VAAS Knife Gate Valve 760/762/765/766/767/768 Series Table of Contents Definition of Terms 1 Safety Instructions 1 Introduction 2 Unpacking 2 Storage 2 Installation 3 Commissioning 3 Cylinder-Operated
More informationEP-2 Si Three-Piston Pump
EP- Si Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.
More informationInstruction Manual For DODGE. Airport Baggage Handling Systems Speed Reducers
Instruction Manual For DODGE Airport Baggage Handling Systems Speed Reducers ABHS TXT109 - TXT115 - TXT125 ABHS TXT209 - TXT215 - TXT225 ABHS TXT309A - TXT315A - TXT325A ABHS TXT409A - TXT415A - TXT425A
More informationUAHT BRAKE CYLINDERS. operation & maintenance instruction , S.12 NOVEMBER, Supersedes issue dated November, 1986
4214-4, S.12 UAHT BRAKE CYLINDERS NOVEMBER, 1989 Supersedes issue dated November, 1986 NOTE: The following description and operation is based on this device and its components being new or this device
More informationCLUTCH Nissan 240SX DESCRIPTION PEDAL HEIGHT & FREE PLAY ADJUST CLUTCH ASSEMBLY R & I Clutch. Pathfinder, Pickup, 240SX, 300ZX
CLUTCH 1990 Nissan 240SX 1990 Clutch Pathfinder, Pickup, 240SX, 300ZX DESCRIPTION Clutch is of dry, single disc type, with a diaphragm spring type pressure plate. Clutch release bearing is prelubricated.
More informationOperating & Maintenance Manual For Steam Conditioning Valve
For Steam Conditioning Valve 1 Table of Contents 1.0 Introduction 3 2.0 Product description 3 3.0 Safety Instruction 4 4.0 Installation and Commissioning 5 5.0 Valve Disassembly 6 6.0 Maintenance 6 7.0
More informationSM64052 Maintenance & Repair Manual Commercial 2" Unisex Coupling - Valved Model 64052
Aerospace Group Conveyance Systems Division Carter Brand Ground Fueling Equipment SM64052 July 2004 Applicable additional manuals: SM64051 Commercial 2" Unisex Coupling, Non-Valved Maintenance & Repair
More informationNorthern Pump A Division of McNally Industries, LLC
Operation & Maintenance Manual for Northern 4900 Injection Operation & Maintenance Manual For Northern 4900 Injection Northern Pump A Division of McNally Industries, LLC 340 West Benson Avenue Grantsburg,
More information1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and
Installation Instructions for 603107 Valve Body Kit C-4 1970 & Later Tools Required Speed Handle or Ratchet 3/8 Drive 1/2 Socket 3/8 Drive 7/16 Socket 3/8 Drive 5/16 Socket 3/8 Drive Small Screwdriver
More informationTHD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS
THD-SERIES S11DA280 THRU S27DA1020 & S11SR280 THRU S27SR1020 DOUBLE ACTING & SPRING RETURN SCOTCH YOKE ACTUATORS INTRODUCTION A-T Controls THD scotch yoke actuators have been designed and engineered to
More informationBinks MODELS & AGITATOR DRIVE UNITS
Binks MODELS 31-393 & 31-394 AGITATOR DRIVE UNITS for Agitator Equipped Drum MODEL 31-393 Includes the following items: 1, 2, and 3. 1 MODEL 31-394 shown. 17 4 3 2 12 13 14 15 2 3 8 5 9 11 8 10 6 7 17
More informationDeZURIK DR 40B ROTARY DIAPHRAGM ACTUATOR
DR 40B ROTARY DIAPHRAGM ACTUATOR Instruction D10506 October 2016 Instructions These instructions provide information about s. They are for use by personnel who are responsible for installation, operation
More informationMaintenance Manual 4½-INCH INTERNAL VALVE F635 SERIES
Maintenance Manual 4½-INCH INTERNAL VALVE F635 SERIES REVISION 1.0 11/01/2004 LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical
More informationDRIVE SHAFT LOCATION INDEX
DRIVE SHAFT LOCATION INDEX 2005 DRIVELINE/AXLE Drive Shaft - MX-5 Miata Fig. 1: Identifying Drive Shaft Location DRIVE SHAFT PRE-INSPECTION 1. Inspect the dust boot on the drive shaft for cracks, damage,
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY
More informationBETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS
BETTIS SERVICE INSTRUCTIONS DISASSEMBLY AND REASSEMBLY FOR CB-SR-S SEISMIC SPRING RETURN SERIES PNEUMATIC ACTUATORS PART NUMBER: 102264 REVISION: "C" DATE: November 2000 Page 1 of 11 1.0 INTRODUCTION 1.1
More informationINSTALLATION INSTRUCTIONS REPAIR SEAL KIT PowerSurvivor 160E
INSTALLATION INSTRUCTIONS REPAIR SEAL KIT PowerSurvivor 160E PURPOSE OF THE KIT The Repair Seal Kit should be installed after 500 hours of operation. It should be installed regardless of whether or not
More informationDisassembly and Reassembly for CBB-SR (Spring Return) Series Pneumatic Actuators
Part Number: VA001-196-31, Rev. 0 Release: May 2012 Disassembly and Reassembly for CBB-SR (Spring Return) Series Pneumatic Actuators Table of Contents Part Number: VA001-196-31, Rev. 0 May 2012 Table of
More informationMACH 1 TSQV SEVERE SERVICE PLUG VALVES
MACH 1 TSQV SEVERE SERVICE PLUG VALVES FOREWORD The Flowserve Corporation has established this Installation, Operating and Maintenance Manual to facilitate field installation, operation and repair of Triple
More informationSTAINLESS STEEL SERIES LSSW HIGH PRESSURE HYDRAULIC CYLINDERS INSTALLATION & OPERATING INSTRUCTIONS
CATALOG: LSSW-00 STAINLESS STEEL SERIES LSSW HIGH PRESSURE HYDRAULIC CYLINDERS INSTALLATION & OPERATING INSTRUCTIONS REMEMBER.... WHEN PERFORMANCE COUNTS SPECIFY LEHIGH LEHIGH FLUID POWER, INC. 1413 ROUTE
More informationStandard Valves Series Globe Valves Series Angle Valves Series Way-Valves
Installation, Operation, Maintenance Instructions Standard Valves Series 035 000 Globe Valves Series 031 000 Angle Valves Series 033 000 3-Way-Valves 1 GENERAL INFORMATION These instructions are designed
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More informationPOWER BRAKES-BENDIX GENERAL DESCRIPTION
5-14 1955 PONTIAC SHOP MANUAL POWER BRAKES-BENDIX GENERAL DESCRIPTION The Bendix power brake unit can be identified by the die-cast hydraulic cylinder and pressed steel filler cap (Fig. 5-17). The Moraine
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationEP-2 Three-Piston Pump
EP- Three-Piston Pump Customer Product Manual Issued 0/ For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) -99 or contact your local Nordson representative.
More informationIMPORTANT!!!! Read this manual before attempting any installation, wiring or operation.
Industrial Turbo Meters Sizes 2" through 6" Installation & Operation Manual IMPORTANT!!!! Read this manual before attempting any installation, wiring or operation. BadgerMeter,Inc. IOM-003-15 Part No.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: Moonroof Wind Deflector Nissan Altima PART NUMBER: 999D UZ000 KIT CONTENTS: Item Qty. Description Service Part Number A B C D E F G H 1
More informationMaintenance Manual. Hydrant Coupler. F250 Series
Hydrant Coupler F250 Series LIST OF EFFECTIVE PAGES On a revised page, the portion of text or illustrations affected by the change is indicated by a vertical line in the outer margin of the page. When
More informationSKF Flex Coupling Installation Instructions
SKF Flex Coupling Installation Instructions The performance of the coupling depends largely upon how you install and maintain. 1. Thoroughly clean all components, paying particular attention to the removal
More informationModel 340 Tune-Up Kit Instructions
Model 340 Tune-Up Kit Instructions Jacobs P/N 019654 tune-up kit instructions Tune-up Kit Contents Illus. No. Jacobs P/N Part Name Quantity Per Kit 4 020229 Upper Seal Ring 3 5 001082 Center Seal Ring
More informationCONTROL VALVES. Installation, Maintenance & Operating Instructions. Read these instructions carefully before installation or servicing.
KOSO HAMMEL DAHL CONTROL VALVES KOSO HAMMEL DAHL 253 Pleasant Street West Bridgewater, MA 02379 tel: 774.517.5300 fax: 774.517.5230 www.hammeldahl.com Installation, Maintenance & Operating Instructions
More informationHorton DriveMaster Fan Clutch 20.06
Horton DriveMaster Fan Clutch 0.06 Fan Clutch Major Rebuild 4 4 5 06/05/00 f0057. Spring Housing/Piston ssembly. Cage Nut. Friction Lining 4. Torx-Head Screws Fig. 4, Friction Lining Removal and Installation
More information#8 VENT VALVE with BRANCH PIPE TEE, Part No
#8 VENT VALVE with BRANCH PIPE TEE, Part No. 579076 JANUARY, 001 Supersedes Issue dated November, 1988 NOTE: The following description and operation is based on this device and its components being new
More informationSD Bendix SR-5 Trailer Spring Brake Valve DESCRIPTION PORTS. 1-1/2" or 3/4" NPT Spring Brake Reservoir Mounting (SPR BK RES)
SD-03-4516 Bendix SR-5 Trailer Spring Brake Valve PRESSURE PROTECTION SR-5 IDENTIFICATION HOLE 1/4 NPT (2) COVER* FIGURE 1 DESCRIPTION 1/4 NPT TRAILER 1/4 NPT SR-5 TRAILER *SHOWN WITH OPTIONAL ANTI-COMPOUNDING
More informationTurbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd
TCI 221500 Turbo 400 Trans Brake Valve Body Shift Pattern: Park Reverse Neutral 1st 2nd 3rd This Valve Body will neutralize at shut-down by putting shifter In 2nd gear position This Kit Contains: (1) Turbo
More informationFuel Gas/ Starting Air Valve Series
Sales Manual Section 364 PRODUCT SPECIFICATION 85380-SERIES Fuel Gas/ Starting Air Valve 85380 - Series GENERAL DESCRIPTION The 85380-Series valve is designed for use either as a fuel gas valve or a starting
More informationCAUTION. 2. Remove the wheel cover or nut covers, as required. Remove the wheel and tire assembly.
Стр. 1 из 16 REAR DRUM BRAKES CAUTION Brake shoes may contain asbestos, which has been determined to be a cancer causing agent. Never clean the brake surfaces with compressed air! Avoid inhaling any dust
More informationTRIM AND TILT TABLE OF CONTENTS TRIM AND TILT
TRIM AND TILT TABLE OF CONTENTS SERVICE CHART................................................................... 326 SYSTEM DESCRIPTION............................................................. 328
More informationASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
More informationD/G-35 Maintenance. Shutdown Procedure During Freezing Temperatures. Daily. Periodically
D/G-35 Maintenance NOTE: The numbers in parentheses are the Reference Numbers on the exploded view illustrations found later in this manual. Daily Check the oil level and the condition of the oil. The
More information3.2 DRIVE TORQUE HUB. Roll, Leak and Brake Testing SECTION 3 - CHASSIS & TURNTABLE. 3-2 JLG Lift
3.2 DRIVE TORQUE HUB Roll, Leak and Brake Testing 10 LUG PATTERN Torque-Hub units should always be roll and leak tested before disassembly and after assembly to make sure that the unit's gears, bearings
More informationPRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY
PRESSURE REGULATOR BACK PRESSURE TO ATMOSPHERE WITH OUTSIDE SUPPLY All Rights Reserved. All contents of this publication including illustrations are believed to be reliable. And while efforts have been
More informationINSTRUCTION MANUAL IM-422 For HTC/COUPLING ASSEMBLY HC-8088
No Revision 2/22/18 INSTRUCTION MANUAL IM-422 HTC/COUPLING ASSEMBLY The Riverhawk Company reserves the right to make changes updating this document without dissemination or notice. The latest revision
More informationSECTION 4 - FUEL/LUBRICATION/COOLING
For Arctic Cat Discount Parts Call 606-678-9623 or 606-561-4983 SECTION 4 - FUEL/LUBRICATION/COOLING 4 TABLE OF CONTENTS Carburetor Specifications... 4-2 Carburetor Schematic... 4-2 Carburetor... 4-3 Cleaning
More informationBLACKMER PISTON AIR/RELIEF VALVE (w/o spring) CONVERSION KIT SAFETY DATA. For Pump Models: TXH3C, TXH3B, TXH3A, TXD2.5A, TXD1225A
BLACKMER PISTON AIR/RELIEF VALVE (w/o spring) CONVERSION KIT INSTALLATION OPERATION & MAINTENANCE INSTRUCTIONS WITH PARTS LIST For Pump Models: TXH3C, TXH3B, TXH3A, TXD2.5A, TXD1225A 964608 Page 1 of 8
More informationFlow Line Controls. Installation & Operations Manual SERIES 20/21 Pneumatic Actuators
Flow Line Controls Installation & Operations Manual SERIES 20/21 Pneumatic Actuators Flow Line Controls, Inc. P.O. Box 677 Schriever, LA 70395 Phone: 985-414-6003 Toll Free 1-800-815-9226 Fax 985-414-6072
More informationGH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS
GH-BETTIS OPERATING & MAINTENANCE INSTRUCTIONS DISASSEMBLY & ASSEMBLY FOR THE T80X-M4-S DOUBLE ACTING SERIES HYDRAULIC ACTUATORS -S INDICATES CYLINDERS ARE IN TANDEM PART NUMBER: 100121 REVISION "A" ECN
More information